AS-i Stromversorgung MLFB-Nr.: 6EP1632-1AL01 (ab Erzeugnisstand: 4) Technische Daten Input +20% Eingangsnennspannung UE Toleranzbereich DC 24 V -15% DC 20,4 V bis 28,8 V statisch DC 18,5 V bis 30,2 V dynamisch Nichtperiodische Ubergangsspannung Netzausfalluberbruckung - UA 25 V - UA 14 V DC 35 V fur 500 ms, Erholzeit 50 s Verpolschutz Einschaltstromsto Paralleldiode und Sicherung 2 It 10 ms bei UE = 20,4 V, IAN 20 ms bei UE = 20,4 V, IAN Aufbauhinweise: Bei der Montage des Gerates ist auf ausreichende Freiraume zu achten, damit die Konvektion gewahrleistet ist. Bei der Installation sind VDE 0100 sowie die einschlagigen DIN/VDE-Vorschriften bzw. landerspezifischen Bestimmungen einzuhalten. Der Versorgungsstromkreis mu durch eine geeignete Trenneinrichtung abgesichert sein. Steckverbinder nicht unter Last ziehen oder stecken! Imax 40 A, t < 3 ms 2 < 4,7 A s Output Ausgangsspannung UAN Toleranz Restwelligkeit DC 30 V DC 29,5 V bis 31,6 V 300 mVSS 0-10 kHz (ASI+/ASI-) Storspannung 50 mVSS 2,4 A 2,8 A 10-500 kHz (ASI+/ASI-) G-Sicherung Gewicht mitgeliefertes Zubehor P30 Schirm M30 Bauschaltplan Koppelmodul Ausgang AS-i Stromversorgung Schutzart nach EN 60529 Sekundarspannung Prufspannung prim./sek. prim./PE sek./PE Funkentstorung nach EN 55011 Storfestigkeit nach IEC801-2/3/4/5 Eingang Flanschdose mit Stift LED grun, aktiv bei UA 28,5 V Feuchteklasse F nach DIN 40040: 15-95 % (indoor), keine Betauung IP65 SELV nach EN 60950/VDE 0805 1500 V AC 500 V AC 500 V AC Klasse B level 3 IP65-Rundsteckverbinder Fa. Interconnectron SEGA 06EMSBN00001 Mehraderleitung 3xAWG14 (2,08 mm) L=500 mm vorbereitet zum Anschlu an Koppelmodul "AS-i PGK" T 6,3 A; 5x20 mm No. 19195 Fa. Wickmann ca. 1,0 kg 1 x Lusterklemme 2 x Flachkabeldichtung fur AS-i Zweidrahtleitung 1 x Reduzierdichtung O 2-7 mm f. Pg 11 Lusterklemme Luftfeuchtigkeit Strombegrenzungseinsatz > 2,85 A 0A Koppelmodul Kurzschluschutz/Uberlast Minimallast Anzeige AS-i Zweidrahtleitung interne Temperaturuberwachung -25 C bis +55 C -10 C bis +45 C bei unbehinderter Konvektion Ansprechschwelle bei Gehausetemperatur T > 80 C Bei Kurzschlu/Uberlast und Ansprechen der internen Temp.-Uberwachung erfolgt ein Absenken der Ausgangsspannung auf Werte unterhalb der Toleranzgrenze. + zulassige Umgebungstemperatur IA = 2,4 A IA = 2,8 A IA =2,8 A bei umg = 45 C IA =2,6 A bei umg = 50 C IA =2,4 A bei umg = 55 C - Nennstrom IN Maximalstrom IA (siehe Derating u. zulassige Umgebungstemperatur) Derating Bestelldaten Bestell-Nr.: 6EP1632-1AL01 Geratemasse Benennung: AS-i Stromversorgung Anschlu an das AS-i Netz Mit Hilfe des Koppelmoduls "AS-i PGK" lat sich der Ubergang von der dreiadrigen Anschluleitung der Stromversorgung zur AS-i Zweidrahtleitung realisieren. Uber die Lusterklemme erfolgt die Verbindung vom Schirm zur Anlagenmasse. Die Anlagenmasse sollte mit mindestens 1,5 mm angeschlossen werden, fur Pg-Verschraubung ist dann die zusatzlich mitgelieferte Dichtung zu verwenden. Die Dichtheit der Pg-Verschraubung bei den AS-i Zweidrahtleitungen wird durch die Verwendung der beiden Profildichtungen erreicht. Um statische Aufladungen zu vermeiden, ist unbedingt der Schirm mit Anlagenmasse zu verbinden. Weitere Informationen zur Anschlumoglichkeit entnehmen Sie bitte: Siemens Kombinationstechnik Katalog KT 10 Siemens AG AUT 7 Werk fur Kombinationstechnik Chemnitz 814333-5 Bs 4 01/97 WKC/BK AS-i Power Supply MLFB-No.: 6EP1632-1AL01 (from Product Version: 4) Instructions for Installation: When installing the device, sufficient clearance should be provided to ensure convection. Technical Data +20% Rated input voltage Uin Tolerance range DC 24 V -15% DC 20.4 V to 28.8 V static DC 18.5 V to 30.2 V dynamic Non-periodic junction voltage Mains failure bridging - Uout 25 V - Uout 14 V DC 35 V for 500 ms, recovery time 50 s Reverse-connect protection Switch-on peak parallel diode and fuse The supply circuit must be protected by an appropriate separating device. 10 ms at Uin = 20.4 V, Iro 20 ms at Uin = 20.4 V, Iro Do not plug or unplug the device under load! Imax 40 A, t < 3 ms 2 < 4.7 A s DC 30 V DC 29.5 V up to 31.6 V 300 mVSS 0-10 kHz (ASi+/ASi-) Interference voltage 50 mVSS 2.4 A 2.8 A 10-500 kHz (ASi+/ASi-) G fuse Weight Accessories supplied AS-i power Ordering Data Order No.: 6EP1632-1AL01 AS-i + shield AS-i - .. . ground of dev ice Designation: AS-i Power Supply Connection diagram of coupling module Output AS-i power supply Degree of protection acc. to EN 60529 Secondary voltage Test voltage prim./sec. prim./PE sec./PE Noise suppression acc. to EN 55011 Noise immunity acc. to IEC801-2/3/4/5 Input Flange pin-type socket LED green, active at Uout 28.5 V class of humidity F acc. to DIN 40040: 15 ... 95 % (indoor), no moisture condensation IP65 SELV acc. to EN 60950/VDE 0805 1500 V AC 500 V AC 500 V AC class B level 3 IP65-circular connector Interconnectron Co. SEGA 06EMSBN00001 multi-strand line 3xAWG14 (2.08 mm) l=500 mm prepared for connection to ASi PGK coupling module T 6.3 A; 5x20 mm no. 19195 Wickmann Co. approx. 1.0 kg 1 x lamp-wire connector 2 x flat cable seal for AS-i two-wire line 1 x reducing seal O 2 ...7 mm for heavygauge conduit thread 11 coupling module Air humidity current limiting device > 2.85 A 0A wire connector Short circuit protection/overload Minimum load Indication AS-i two-wire line Internal temperature control between -25 C and +55 C between -10 C and +45 C with free convection Response threshold at a case temperature of T > 80 C In the case of short circuit/overload and response of the internal temperature control the output voltage is reduced to values below the tolerance limit. + Permissible ambient temperature Iout = 2.4 A Iout = 2.8 A Iout =2.8 A at amb = 45 C Iout =2.6 A at amb = 50 C Iout =2.4 A at amb = 55 C - Rated current IR Maximum current Iout (see Derating and Permissible Ambient Temperature) Derating Height: 57 mm 1) Mounting screws: Fillister-head screw with hexagonal socket-head M4x16 8.8 DIN 912 AS-i + AS-i - Rated output voltage UOR Tolerance Residual ripple screen . Output screen 2 It Installation must be performed acc. to VDE 0100 and the relevant DIN/VDE regulations as well as national standards, resp. AS-i + AS-i - Input Connection to the AS-i supply system The ASi PGK Coupling Module can be used to realise transition from the three-wire connection line of the power supply to the AS-i two-wire line. The connection from the shield to the equipment ground is provided by the lamp-wire connector. The equipment ground should be connected to 1.5 mm at least; for the heavy-gauge screw connection, the additionally supplied seal should be used. The tightness of the heavy-gauge screw connection with the AS-i two-wire lines is provided by two formed gaskets. To avoid static charging, it is absolutely necessary to connect the shield with the equipment ground. For further information on connecting and wiring facilities see: Siemens Kombinationstechnik Catalogue KT 10 Siemens AG AUT 7 Werk fur Kombinationstechnik Chemnitz 814333-5 Bs 4 01/97 WKC/BK