D Low Power Consumption D Wide Common-Mode and Differential Voltage Ranges D Low Input Bias and Offset Currents D Output Short-Circuit Protection D Low Total Harmonic Distortion . . . 0.003% Typ SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 D Low Noise D D D D D Vn = 18 nV/Hz Typ at f = 1 kHz High Input Impedance . . . JFET Input Stage Internal Frequency Compensation Latch-Up-Free Operation High Slew Rate . . . 13 V/s Typ Common-Mode Input Voltage Range Includes VCC+ description/ordering information The JFET-input operational amplifiers in the TL07x series are similar to the TL08x series, with low input bias and offset currents and fast slew rate. The low harmonic distortion and low noise make the TL07x series ideally suited for high-fidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance) coupled with bipolar output stages integrated on a single monolithic chip. The C-suffix devices are characterized for operation from 0C to 70C. The I-suffix devices are characterized for operation from -40C to 85C. The M-suffix devices are characterized for operation over the full military temperature range of -55C to 125C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2005, Texas Instruments Incorporated !" # $%&" !# '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ '*%$"# $')!" " 12313 !)) '!!&"&# !& "&#"&* %)&## ",&.#& "&*+ !)) ",& '*%$"# '*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 description/ordering information (continued) ORDERING INFORMATION TA VIOmax AT 25C TOP-SIDE MARKING Tube of 50 TL071CP TL071CP Tube of 50 TL072CP TL072CP Tube of 25 TL074CN TL074CN Tube of 75 TL071CD Reel of 2500 TL071CDR Tube of 75 TL072CD Reel of 2500 TL072CDR Tube of 50 TL074CD Reel of 2500 TL074CDR Reel of 2000 TL074CNSR TL074 Reel of 2000 TL071CPSR TL071 Reel of 2000 TL072CPSR T072 Reel of 2000 TL072CPWR T072 Tube of 90 TL074CPW Reel of 2000 TL074CPWR Tube of 50 TL071ACP TL071ACP Tube of 50 TL072ACP TL072ACP Tube of 25 TL074ACN TL074ACN Tube of 75 TL071ACD Reel of 2500 TL071ACDR Tube of 75 TL072ACD Reel of 2500 TL072ACDR Tube of 50 TL074ACD Reel of 2500 TL074ACDR SOP (PS) Reel of 2000 TL072ACPSR T072A SOP (NS) Reel of 2000 TL074ACNSR TL074A Tube of 50 TL071BCP TL071BCP Tube of 50 TL072BCP TL072BCP Tube of 25 TL074BCN TL074BCN Tube of 75 TL071BCD Reel of 2500 TL071BCDR Tube of 75 TL072BCD Reel of 2500 TL072BCDR Tube of 50 TL074BCD Reel of 2500 TL074BCDR PDIP (P) PDIP (N) SOIC (D) 10 mV SOP (NS) SOP (PS) TSSOP (PW) PDIP (P) PDIP (N) 0C to 70C 6 mV ORDERABLE PART NUMBER PACKAGE SOIC (D) PDIP (P) PDIP (N) 3 mV SOIC (D) TL071C TL072C TL074C T074 071AC 072AC TL074AC 071BC 072BC TL074BC SOP (NS) Reel of 2000 TL074BCNSR TL074B Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 description/ordering information (continued) ORDERING INFORMATION TA VIOmax AT 25C TL071IP TL071IP Tube of 50 TL072IP TL072IP Tube of 25 TL074IN TL074IN Tube of 75 TL071ID Reel of 2500 TL071IDR Tube of 75 TL072ID Reel of 2500 TL072IDR Tube of 50 TL074ID Reel of 2500 TL074IDR CDIP (JG) Tube of 50 TL072MJGB TL072MJGB CFP (U) Tube of 150 TL072MUB TL072MUB LCCC (FK) Tube of 55 TL072MFKB TL072MFKB CDIP (J) Tube of 25 TL074MJB TL074MJB CFP (W) Tube of 25 TL074MWB TL074MWB LCCC (FK) Tube of 55 TL074MFKB PDIP (N) 6 mV SOIC (D) 6 mV -55C to 125C 9 mV TOP-SIDE MARKING Tube of 50 PDIP (P) -40C -40 C to 85 85C C ORDERABLE PART NUMBER PACKAGE TL071I TL072I TL074I TL074MFKB Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TL071, TL071A, TL071B D, P, OR PS PACKAGE (TOP VIEW) OFFSET N1 IN- IN+ VCC- 1 8 2 7 3 6 4 5 TL072, TL072A, TL072B D, JG, P, PS, OR PW PACKAGE (TOP VIEW) NC VCC+ OUT OFFSET N2 1OUT 1IN- 1IN+ VCC- 1 8 2 7 3 6 4 5 TL074A, TL074B D, J, N, NS, OR PW PACKAGE TL074 . . . D, J, N, NS, PW, OR W PACKAGE (TOP VIEW) VCC+ 2OUT 2IN- 2IN+ 1OUT 1IN- 1IN+ VCC+ 2IN+ 2IN- 2OUT TL072 U PACKAGE (TOP VIEW) NC 1OUT 1IN- 1IN+ VCC- 5 17 6 16 7 15 8 14 9 10 11 12 13 8 4 7 5 6 3 12 4 11 5 10 6 9 7 8 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1IN- 1OUT NC 4OUT 4IN- NC 2OUT NC 2IN- NC 1IN+ NC VCC+ NC 2IN+ 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC - No internal connection symbols TL071 TL072 (each amplifier) TL074 (each amplifier) OFFSET N1 IN+ + IN+ + IN- - OUT IN- - OUT OFFSET N2 4 POST OFFICE BOX 655303 4OUT 4IN- 4IN+ VCC- 3IN+ 3IN- 3OUT TL074 FK PACKAGE (TOP VIEW) NC 1OUT NC V CC+ NC NC VCC+ NC OUT NC 13 2IN- 2OUT NC 3OUT 3IN- 3 2 1 20 19 18 9 3 NC V CC- NC 2IN+ NC 4 NC 1IN- NC 1IN+ NC NC V CC- NC OFFSET N2 NC NC IN- NC IN+ NC 10 2 14 2 NC VCC+ 2OUT 2IN- 2IN+ TL072 FK PACKAGE (TOP VIEW) NC OFFSET N1 NC NC NC TL071 FK PACKAGE (TOP VIEW) 1 1 * DALLAS, TEXAS 75265 4IN+ NC VCC- NC 3IN+ SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 schematic (each amplifier) VCC+ IN+ 64 IN- 128 OUT 64 C1 18 pF III AAA AAA 1080 1080 AAAAA AAAAA VCC- OFFSET N1 OFFSET N2 TL071 Only All component values shown are nominal. COMPONENT COUNT COMPONENT TYPE TL071 Resistors 11 Transistors 14 JFET 2 Diodes 1 Capacitors 1 epi-FET 1 Includes bias and trim circuitry POST OFFICE BOX 655303 TL072 TL074 22 28 4 2 2 2 44 56 6 4 4 4 * DALLAS, TEXAS 75265 5 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage (see Note 1): VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V VCC- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -18 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V Input voltage, VI (see Notes 1 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited Package thermal impedance, JA (see Notes 5 and 6): D package (8 pin) . . . . . . . . . . . . . . . . . . . . . . 97C/W D package (14 pin) . . . . . . . . . . . . . . . . . . . . . 86C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85C/W PS package . . . . . . . . . . . . . . . . . . . . . . . . . . . 95C/W PW package (8 pin) . . . . . . . . . . . . . . . . . . . 149C/W PW package (14 pin) . . . . . . . . . . . . . . . . . . 113C/W U package . . . . . . . . . . . . . . . . . . . . . . . . . . . 185C/W Package thermal impedance, JC (see Notes 7 and 8): FK package . . . . . . . . . . . . . . . . . . . . . . . . . 5.61C/W J package . . . . . . . . . . . . . . . . . . . . . . . . . 15.05C/W JG package . . . . . . . . . . . . . . . . . . . . . . . . . 14.5C/W W package . . . . . . . . . . . . . . . . . . . . . . . . 14.65C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: J, JG, or W package . . . . . . . . . . . . 300C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC-. 2. Differential voltages are at IN+, with respect to IN-. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 5. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. 6. The package thermal impedance is calculated in accordance with JESD 51-7. 7. Maximum power dissipation is a function of TJ(max), JC, and TC. The maximum allowable power dissipation at any allowable case temperature is PD = (TJ(max) - TC)/JC. Operating at the absolute maximum TJ of 150C can affect reliability. 8. The package thermal impedance is calculated in accordance with MIL-STD-883. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Input resistance ri AVD = 100 Crosstalk attenuation VO1/ VO2 No load 25C 25C 70 70 15 120 1.4 100 100 2.5 80 120 1.4 100 100 1012 1012 200 3 75 25 50 13.5 -12 to 15 65 5 18 3 TYP 3 200 10 25 12 12 10 13.5 12 11 12 -12 to 15 11 7 MIN TL071AC TL072AC TL074AC 2.5 7 200 2 100 7.5 6 MAX 80 75 25 50 10 12 12 11 MIN 120 1.4 100 100 1012 3 200 13.5 -12 to 15 65 5 18 2 TYP TL071BC TL072BC TL074BC 2.5 7 200 2 100 5 3 MAX 80 75 25 50 10 12 12 11 MIN 120 1.4 100 100 1012 3 200 13.5 -12 to 15 65 5 18 3 TYP TL071I TL072I TL074I 2.5 20 200 2 100 8 6 MAX dB mA dB dB MHz V/mV V V nA pA nA pA V/C mV UNIT All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified. Full range is TA = 0C to 70C for TL07_C,TL07_AC, TL07_BC and is TA = -40C to 85C for TL07_I. Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as shown in Figure 4. Pulse techniques must be used that maintain the junction temperature as close to the ambient temperature as possible. VO = 0, 25C VCC = 9 V to 15 V, RS = 50 VO = 0, Supply current (each amplifier) 25C Full range 25C Full range VIC = VICRmin, RS = 50 VO = 0, VO = 10 V, ICC kSVR Common-mode rejection ratio Supply-voltage rejection ratio (VCC /VIO) 25C Unity-gain bandwidth B1 CMRR 25C Large-signal differential voltage amplification AVD RL 2 k RL 10 k VOM 25C Maximum peak output voltage swing 25C 25 C Full range 10 200 25C 100 13 10 MAX Full range 65 5 25C 3 TYP 18 MIN Full range Full range Common-mode input voltage range RL 2 k RS = 50 RS = 50 25C TA VICR RL = 10 k VO = 0 VO = 0 Input offset current IIO Input bias current VO = 0, Temperature coefficient of input offset voltage V IO IIB VO = 0, Input offset voltage TEST CONDITIONS VIO PARAMETER TL071C TL072C TL074C electrical characteristics, VCC = 15 V (unless otherwise noted) 444 4 4 4 4 4 4 4 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 7 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 electrical characteristics, VCC = 15 V (unless otherwise noted) PARAMETER TEST CONDITIONS TL071M TL072M TA MIN 25C TYP MAX 3 6 VIO Input offset voltage VO = 0, RS = 50 Full range V IO Temperature coefficient of input offset voltage VO = 0, RS = 50 Full range 18 25C 5 IIO Input offset current VO = 0 IIB Input bias current VICR Common-mode input voltage range VOM Maximum peak output voltage swing TL074M MIN TYP 3 9 Full range 100 5 25C 65 200 65 25C 11 -12 to 15 11 -12 to 15 RL 10 k 25C 12 13.5 12 13.5 Full range RL 2 k 25C 12 12 10 10 35 200 35 mV V/C 18 50 RL = 10 k 9 15 20 VO = 0 UNIT MAX 100 pA 20 nA 200 pA 50 nA V V 200 AVD Large-signal differential voltage amplification VO = 10 V, B1 Unity-gain bandwidth TA = 25C 3 3 ri Input resistance TA = 25C 1012 1012 CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 VO = 0, 25C 80 86 80 86 dB kSVR Supply-voltage rejection ratio (VCC/VIO) VCC = 9 V to 15 V, RS = 50 VO = 0, 25C 80 86 80 86 dB ICC Supply current (each amplifier) VO = 0, 25C RL 2 k No load 15 V/mV 15 1.4 2.5 1.4 MHz 2.5 mA VO1/VO2 Crosstalk attenuation AVD = 100 25C 120 120 dB Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as shown in Figure 4. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified. Full range is TA = -55C to 125C. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 operating characteristics, VCC = 15 V, TA = 25C TL07xM PARAMETER TEST CONDITIONS SR Slew rate at unity gain VI = 10 V, CL = 100 pF, RL = 2 k, See Figure 1 tr Rise-time overshoot factor VI = 20 mV, CL = 100 pF, RL = 2 k, See Figure 1 Vn Equivalent input noise voltage RS = 20 In Equivalent input noise current RS = 20 , f = 1 kHz THD Total harmonic distortion VIrms = 6 V, RL 2 k, f = 1 kHz AVD = 1, RS 1 k, MIN TYP 5 13 ALL OTHERS MAX MAX UNIT MIN TYP 8 13 V/s s 0.1 0.1 20% 20% 18 18 nV/Hz 4 4 V 0.01 0.01 0.003 % 0.003% f = 1 kHz f = 10 Hz to 10 kHz pA/Hz PARAMETER MEASUREMENT INFORMATION 10 k - VI + CL = 100 pF 1 k VO RL = 2 k + RL IN- CL = 100 pF Figure 2. Gain-of-10 Inverting Amplifier Figure 1. Unity-Gain Amplifier - TL071 OUT IN+ N2 + VI - VO N1 100 k 1.5 k VCC- Figure 3. Input Offset-Voltage Null Circuit POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS Table of Graphs FIGURE IIB Input bias current vs Free-air temperature 4 VOM Maximum output voltage vs Frequency vs Free-air temperature vs Load resistance vs Supply voltage 5, 6, 7 8 9 10 AVD Large-signal differential voltage amplification vs Free-air temperature vs Frequency 11 12 Phase shift vs Frequency 12 Normalized unity-gain bandwidth vs Free-air temperature 13 Normalized phase shift vs Free-air temperature 13 CMRR Common-mode rejection ratio vs Free-air temperature 14 ICC Supply current vs Supply voltage vs Free-air temperature 15 16 PD Total power dissipation vs Free-air temperature 17 Normalized slew rate vs Free-air temperature 18 Vn Equivalent input noise voltage vs Frequency 19 THD Total harmonic distortion vs Frequency 20 Large-signal pulse response vs Time 21 Output voltage vs Elapsed time 22 VO 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE 100 15 VOM VOM - Maximum Peak Output Voltage - V IIIB- IB Input Bias Current - nA VCC = 15 V 10 1 -50 -25 0 25 50 75 100 VCC = 15 V VCC = 10 V 7.5 IIII VCC = 5 V 5 2.5 125 0 100 1k TA - Free-Air Temperature - C Figure 4 VCC = 15 V 10 15 RL = 2 k TA = 25C See Figure 2 VCC = 10 V 7.5 AA AA AA 5 VCC = 5 V 2.5 0 100 1k 10 k 100 k f - Frequency - Hz 1M 10 M MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY 1M 10 M VOM VOM - Maximum Peak Output Voltage - V VOM VOM - Maximum Peak Output Voltage - V IIIII IIIII 12.5 10 k 100 k f - Frequency - Hz Figure 5 MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY 15 RL = 10 k TA = 25C See Figure 2 IIIII 10 AAA AAA 0.1 0.01 -75 12.5 IIIII IIIII 12.5 10 IIII IIII VCC = 15 V RL = 2 k See Figure 2 TA = 25C IIIII IIIII TA = -55C 7.5 5 AAA AAA AAA TA = 125C 2.5 0 10 k Figure 6 40 k 100 k 400 k 1 M f - Frequency - Hz 4M 10 M Figure 7 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS MAXIMUM PEAK OUTPUT VOLTAGE vs LOAD RESISTANCE MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 15 RL = 10 k IIII IIII 12.5 VOM VOM - Maximum Peak Output Voltage - V VOM - Maximum Peak Output Voltage - V VOM 15 RL = 2 k 10 7.5 5 AA AA 2.5 VCC = 15 V See Figure 2 0 -75 -50 -25 0 25 50 75 100 125 VCC = 15 V TA = 25C See Figure 2 12.5 AA AA 10 7.5 5 2.5 0 0.1 0.2 TA - Free-Air Temperature - C 0.4 4 7 10 Figure 9 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE MAXIMUM PEAK OUTPUT VOLTAGE vs SUPPLY VOLTAGE 15 1000 RL = 10 k TA = 25C 12.5 400 AVD A VD - Large-Signal Differential Voltage Amplification - V/mV VOM VOM - Maximum Peak Output Voltage - V 2 RL - Load Resistance - k Figure 8 10 7.5 AA AA AA 0.7 1 5 2.5 200 100 40 20 10 4 2 0 0 2 4 6 8 10 12 14 16 1 -75 VCC = 15 V VO = 10 V RL = 2 k -50 -25 0 25 50 75 100 TA - Free-Air Temperature - C |VCC| - Supply Voltage - V Figure 11 Figure 10 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 125 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY VCC = 5 V to 15 V RL = 2 k TA = 25C 105 104 0 Differential Voltage Amplification 103 45 102 Phase Shift AVD A VD - Large-Signal Differential Voltage Amplification 106 90 Phase Shift 101 135 1 10 1 100 1k 10 k 100 k f - Frequency - Hz 1M 180 10 M Figure 12 NORMALIZED UNITY-GAIN BANDWIDTH AND PHASE SHIFT vs FREE-AIR TEMPERATURE 1.03 Unity-Gain Bandwidth 1.2 1.01 1.1 1 Phase Shift 1 0.99 0.9 0.8 0.7 -75 1.02 VCC = 15 V RL = 2 k f = B1 for Phase Shift -50 -25 0 25 50 75 100 TA - Free-Air Temperature - C Normalized Phase Shift Normalized Unity-Gain Bandwidth 1.3 0.98 0.97 125 Figure 13 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS SUPPLY CURRENT PER AMPLIFIER vs SUPPLY VOLTAGE COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 2 VCC = 15 V RL = 10 k ICC - Supply Current Per Amplifier - mA I CC CMRR - Common-Mode Rejection Ratio - dB 89 88 87 86 85 83 -75 1.6 1.4 1.2 1 0.8 AA AA 84 -50 -25 0 25 50 75 100 TA = 25C No Signal No Load 1.8 0.6 0.4 0.2 0 125 0 2 TA - Free-Air Temperature - C 4 SUPPLY CURRENT PER AMPLIFIER vs FREE-AIR TEMPERATURE 10 12 14 VCC = 15 V No Signal No Load 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 250 VCC = 15 V No Signal No Load 225 200 175 TL074 150 125 IIII IIII 100 TL072 75 TL071 50 25 -50 -25 0 25 50 75 100 125 0 -75 -50 TA - Free-Air Temperature - C -25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 16 Figure 17 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 14 16 TOTAL POWER DISSIPATION vs FREE-AIR TEMPERATURE PD PD - Total Power Dissipation - mW ICC - Supply Current Per Amplifier - mA I CC 2 0 -75 8 Figure 15 Figure 14 AAA AAA AAA 6 |VCC| - Supply Voltage - V POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 125 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS NORMALIZED SLEW RATE vs FREE-AIR TEMPERATURE AAA AAA AAA AAA Vn V nV/ Hz n - Equivalent Input Noise Voltage - nV/Hz Normalized Slew Rate - V/ s 1.15 VCC = 15 V RL = 2 k CL = 100 pF 1.10 1.05 1 0.95 0.90 0.85 -75 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 50 VCC = 15 V AVD = 10 RS = 20 TA = 25C 40 30 20 10 0 -50 -25 0 25 50 75 100 10 125 40 100 TA - Free-Air Temperature - C Figure 18 6 VCC = 15 V AVD = 1 VI(RMS) = 6 V TA = 25C 0.1 0.04 0.01 0.004 0.001 100 400 1k 4 k 10 k f - Frequency - Hz VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE VI and VO - Input and Output Voltages - V THD - Total Harmonic Distortion - % 0.4 40 k 100 k Figure 19 TOTAL HARMONIC DISTORTION vs FREQUENCY 1 400 1 k 4 k 10 k f - Frequency - Hz 40 k 100 k VCC = 15 V RL = 2 k CL = 100 pF TA = 25C 4 Output 2 0 AA AA AA AA III III -2 Input -4 -6 0 0.5 1 1.5 t - Time - s 2 2.5 3 3.5 Figure 21 Figure 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs ELAPSED TIME 28 24 VO V O - Output Voltage - mV Overshoot 20 90% 16 12 AAA AAA 8 4 VCC = 15 V RL = 2 k TA = 25C 10% 0 tr -4 0 0.1 0.2 0.3 0.4 0.5 t - Elapsed Time - s 0.6 Figure 22 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 0.7 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 APPLICATION INFORMATION Table of Application Diagrams PART NUMBER FIGURE 0.5-Hz square-wave oscillator TL071 23 High-Q notch filter TL071 24 Audio-distribution amplifier TL074 25 100-kHz quadrature oscillator TL072 26 AC amplifier TL071 27 APPLICATION DIAGRAM RF = 100 k VCC+ - Output - TL071 CF = 3.3 F Input R1 R2 C3 + -15 V R1 + R2 + 2R3 + 1.5 MW R3 C1 C2 9.1 k 1 2p R F C F Figure 23. 0.5-Hz Square-Wave Oscillator C1 + C2 + C3 + 110 pF 2 1 fO + + 1 kHz 2p R1 C1 Figure 24. High-Q Notch Filter VCC+ - 1 M TL074 VCC+ + VCC- - 1 F TL074 VCC+ + 100 k Output B VCC- VCC+ VCC+ 100 k TL074 Output C + 100 F TL074 VCC- 100 k + 100 k - Input Output A - f+ Output VCC- 1 k 3.3 k TL071 + 15 V 3.3 k VCC- Figure 25. Audio-Distribution Amplifier POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 SLOS080J - SEPTEMBER 1978 - REVISED MARCH 2005 APPLICATION INFORMATION 1N4148 6 sin t 18 k (see Note A) -15 V 18 pF 18 pF 1 k VCC+ VCC+ - 88.4 k TL072 - + VCC- 18 pF 6 cos t TL072 + 88.4 k 1 k VCC- 15 V 1N4148 18 k (see Note A) 88.4 k NOTE A: These resistor values may be adjusted for a symmetrical output. Figure 26. 100-kHz Quadrature Oscillator VCC+ 0.1 F 10 k 10 k 1 M - IN- TL071 50 + IN+ 0.1 F 10 k N2 N1 100 k Figure 27. AC Amplifier 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 OUT PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 PACKAGING INFORMATION Orderable Device Status (1) 8102304HA OBSOLETE 81023052A ACTIVE 8102305HA ACTIVE 8102305PA ACTIVE 81023062A ACTIVE LCCC 8102306CA ACTIVE 8102306DA ACTIVE JM38510/11905BPA ACTIVE JM38510/11906BCA OBSOLETE TL071ACD ACTIVE TL071ACDE4 ACTIVE TL071ACDG4 Pins Package Eco Plan (2) Qty Package Drawing LCCC FK 20 1 TBD CFP U 10 1 TBD A42 N / A for Pkg Type CDIP JG 8 1 TBD A42 N / A for Pkg Type FK 20 1 TBD CDIP J 14 1 TBD A42 N / A for Pkg Type CFP W 14 1 TBD A42 N / A for Pkg Type CDIP JG 8 1 TBD A42 N / A for Pkg Type CDIP J 14 TBD Call TI SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071ACDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071ACDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071ACDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071ACP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071ACPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071BCD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071BCDE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071BCDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071BCDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071BCDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071BCDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071BCP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071BCPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071CD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CDE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CDR ACTIVE SOIC D 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM 10 TBD Addendum-Page 1 Lead/Ball Finish MSL Peak Temp (3) Package Type Call TI Call TI POST-PLATE N / A for Pkg Type POST-PLATE N / A for Pkg Type Call TI PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL071CDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071CPSR ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CPSRE4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CPSRG4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071CPWLE OBSOLETE TSSOP PW 8 TL071ID ACTIVE SOIC D 8 TL071IDE4 ACTIVE SOIC D TL071IDG4 ACTIVE SOIC TL071IDR ACTIVE TL071IDRE4 Lead/Ball Finish MSL Peak Temp (3) no Sb/Br) TBD Call TI Call TI 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL071IJG OBSOLETE CDIP JG 8 TBD Call TI TL071IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL071MFKB OBSOLETE LCCC FK 20 TBD Call TI Call TI Call TI TL071MJG OBSOLETE CDIP JG 8 TBD Call TI Call TI TL071MJGB OBSOLETE CDIP JG 8 TBD Call TI Call TI TL072ACD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072ACDE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072ACDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072ACDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072ACDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072ACDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072ACJG OBSOLETE CDIP JG 8 TL072ACP ACTIVE PDIP P 8 50 Addendum-Page 2 TBD Call TI Pb-Free CU NIPDAU Call TI N / A for Pkg Type PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL072ACPE4 ACTIVE PDIP P 8 TL072ACPSR ACTIVE SO PS 8 TL072ACPSRE4 ACTIVE SO PS TL072ACPSRG4 ACTIVE SO TL072BCD ACTIVE TL072BCDE4 Lead/Ball Finish MSL Peak Temp (3) (RoHS) 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072BCDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072BCDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072BCDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072BCDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072BCP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL072BCPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL072CD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CDE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL072CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL072CPSLE OBSOLETE SO PS 8 TL072CPSR ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CPSRE4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CPSRG4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CPWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL072CPWRE4 ACTIVE TSSOP PW 8 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM TBD Addendum-Page 3 Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL072CPWRG4 ACTIVE TSSOP PW 8 TL072ID ACTIVE SOIC D 8 75 TL072IDE4 ACTIVE SOIC D 8 TL072IDG4 ACTIVE SOIC D 8 TL072IDR ACTIVE SOIC D TL072IDRE4 ACTIVE SOIC TL072IDRG4 ACTIVE TL072IP Lead/Ball Finish MSL Peak Temp (3) no Sb/Br) 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL072IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL072MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type TL072MJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type TL072MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type TL072MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type TL074ACD ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACDE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACDRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACJ OBSOLETE CDIP J 14 TBD Call TI TL074ACN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074ACNE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074ACNSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACNSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ACNSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074BCD ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074BCDE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 4 Call TI PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL074BCDG4 ACTIVE SOIC D 14 TL074BCDR ACTIVE SOIC D TL074BCDRE4 ACTIVE SOIC TL074BCDRG4 ACTIVE TL074BCN 50 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074BCNE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074CD ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CDE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CDRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074CNE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074CNSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CNSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CNSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CPWE4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CPWLE OBSOLETE TSSOP PW 14 TBD Call TI TL074CPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CPWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074CPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074ID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL074IDE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 5 Call TI PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL074IDG4 ACTIVE SOIC D 14 TL074IDR ACTIVE SOIC D TL074IDRE4 ACTIVE SOIC TL074IDRG4 ACTIVE TL074IJ 50 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OBSOLETE CDIP J 14 TL074IN ACTIVE PDIP N 14 TL074INE4 ACTIVE PDIP N TBD Call TI Call TI 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL074MFK ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type TL074MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type TL074MJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type TL074MJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type TL074MWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 6 PACKAGE MATERIALS INFORMATION www.ti.com 7-Aug-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TL071ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071BCDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL071CPSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 TL071IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL072ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL072ACPSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 TL072BCDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL072CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL072CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL072CPSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 TL072CPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 TL072IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL072IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL074ACDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TL074ACNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 TL074BCDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 7-Aug-2009 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TL074CDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TL074CNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 TL074CPWR TSSOP PW 14 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1 TL074IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL071ACDR SOIC D 8 2500 340.5 338.1 20.6 TL071BCDR SOIC D 8 2500 340.5 338.1 20.6 TL071CDR SOIC D 8 2500 346.0 346.0 29.0 TL071CDR SOIC D 8 2500 340.5 338.1 20.6 TL071CPSR SO PS 8 2000 346.0 346.0 33.0 TL071IDR SOIC D 8 2500 340.5 338.1 20.6 TL072ACDR SOIC D 8 2500 340.5 338.1 20.6 TL072ACPSR SO PS 8 2000 346.0 346.0 33.0 TL072BCDR SOIC D 8 2500 340.5 338.1 20.6 TL072CDR SOIC D 8 2500 346.0 346.0 29.0 TL072CDR SOIC D 8 2500 340.5 338.1 20.6 TL072CPSR SO PS 8 2000 346.0 346.0 33.0 TL072CPWR TSSOP PW 8 2000 346.0 346.0 29.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 7-Aug-2009 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL072IDR SOIC D 8 2500 340.5 338.1 20.6 TL072IDR SOIC D 8 2500 346.0 346.0 29.0 TL074ACDR SOIC D 14 2500 333.2 345.9 28.6 TL074ACNSR SO NS 14 2000 346.0 346.0 33.0 TL074BCDR SOIC D 14 2500 333.2 345.9 28.6 TL074CDR SOIC D 14 2500 333.2 345.9 28.6 TL074CNSR SO NS 14 2000 346.0 346.0 33.0 TL074CPWR TSSOP PW 14 2000 346.0 346.0 29.0 TL074IDR SOIC D 14 2500 333.2 345.9 28.6 Pack Materials-Page 3 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MLCC006B - OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPDI001A - JANUARY 1995 - REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MCER001A - JANUARY 1995 - REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0-15 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated