ASAHI KASEI [AK5386] AK5386 Single-ended 24-Bit 192kHz ADC GENERAL DESCRIPTION The AK5386 is a stereo A/D Converter with wide sampling rate of 8kHz 216kHz and is suitable for consumer to professional audio system. The AK5386 achieves high accuracy and low cost by using Enhanced dual bit techniques. The AK5386 requires no external components because the analog inputs are single-ended. The audio interface has two formats (MSB justified, I2S) and can correspond to various systems like DVD Recorder, AV Receiver, PC Sound card and Music Instrument recording. FEATURES Single-ended Input Digital HPF for DC-Offset cancel S/(N+D): 96dB DR: 110dB S/N: 110dB Linear Phase Digital Anti-Alias Filtering Passband: 0 21.768kHz (@ fs=48kHz) Passband Ripple: 0.005dB Stopband Attenuation: 80dB Master Clock: 512fs/768fs (Normal Speed) 256fs/384fs (Double Speed) 128fs/192fs (Quad Speed) Sampling Frequency: Normal Speed: 8kHz 54kHz (512fs) 8kHz 48kHz (768fs) Double Speed: 54kHz 108kHz (256fs) 48kHz 96kHz (384fs) Quad Speed: 108kHz 216kHz (128fs) 96kHz 192kHz (192fs) Master / Slave Mode 2 Audio Interface: 24bit MSB justified / I S selectable Input level: CMOS Power Supply: Analog: 4.5 5.5V Digital: 2.7 3.6V (Normal Speed) 3.0 3.6V (Double Speed, Quad Speed) Ta = -40 85C Small 16pin TSSOP Package AK5357/58/59/81 Pin-compatible MS0579-E-00 2006/12 -1- ASAHI KASEI [AK5386] VA AGND MCLK VD DGND Clock Divider AINL AINR VCOM Modulator Decimation Filter Modulator Decimation Filter SCLK Serial I/O Interface Voltage Reference CKS2 CKS1 LRCK CKS0 PDN SDTO DIF Block Diagram Compatibility with AK5357, AK5358, AK5359, AK5381 and AK5386 fs S/(N+D) DR MCLK @ 48kHz VIH @ TTL Level Mode VA(Analog Supply) AK5357 4kHz to 96kHz 88dB 102dB AK5358 8kHz to 96kHz 92dB 102dB AK5381 4kHz to 96kHz 96dB 106dB AK5359 8kHz to 216kHz 94dB 102dB 256/512/384/768fs 256/512/384/768fs 256/512/384/768fs 256/512/384/768fs AK5386 8kHz to 216kHz 96dB 110dB 512/768fs 2.2V 2.2V 2.4V Not Available Not Available 2.7 to 5.5V 4.5 to 5.5V 4.5 to 5.5V VD (Digital Supply) 2.7 to 5.5V 2.7 to 5.5V Available ET: -20+85C VT: -40+85C Not Available ET: -20+85C 4.5 to 5.5V 2.7 to 5.5V 3.0 to 5.5V@ fs=96kHz Available ET: -20+85C VT: -40+85C XT: -40+85C 4.5 to 5.5V 2.7 to 3.6V 3.0 to 3.6V @ fs=96k, 192kHz Available VT: -40+85C HPF Disable Operating Temperature MS0579-E-00 2.7 to 5.5V Available ET: -20+85C VT: -40+85C 2006/12 -2- ASAHI KASEI [AK5386] Ordering Guide 16pin TSSOP (0.65mm pitch) -40 +85C Evaluation Board for AK5386 AK5386VT AKD5386 Pin Layout AINR 1 16 CKS0 AINL 2 15 CKS2 CKS1 3 14 DIF VCOM 4 13 PDN AGND 5 12 SCLK VA 6 11 MCLK VD 7 10 LRCK DGND 8 9 SDTO Top View PIN / FUNCTION No. Pin Name 1 2 3 AINR AINL CKS1 I/O Function I I I Rch Analog Input Pin Lch Analog Input Pin Mode Select 1 Pin Common Voltage Output Pin, VA/2 4 VCOM O Bias voltage of ADC input. 5 AGND Analog Ground Pin 6 VA Analog Power Supply Pin, 5V 7 VD Digital Power Supply Pin, 3.3V 8 DGND Digital Ground Pin Audio Serial Data Output Pin 9 SDTO O "L" Output at Power-down mode. Output Channel Clock Pin 10 LRCK I/O "L" Output in Master Mode at Power-down mode. 11 MCLK I Master Clock Input Pin Audio Serial Data Clock Pin 12 SCLK I/O "L" Output in Master Mode at Power-down mode. Power Down & Reset Mode Pin 13 PDN I "H": Power up, "L": Power down & Reset The AK5386 must be reset once upon power-up. Audio Interface Format Pin 14 DIF I "H": 24bit I2S Compatible, "L": 24bit MSB justified 15 CKS2 I Mode Select 2 Pin 16 CKS0 I Mode Select 0 Pin Note: Do not allow all digital input pins except for analog input pins (AINL and AINR pins) to float. MS0579-E-00 2006/12 -3- ASAHI KASEI [AK5386] Handling of Unused Pin The unused input pins should be processed appropriately as below. Classification Analog Pin Name AINL AINR Setting This pin should be open. This pin should be open. ABSOLUTE MAXIMUM RATINGS (AGND, DGND=0V; Note 1) Parameter Symbol min Power Supplies: Analog VA -0.3 (Note 2) Digital VD -0.3 Input Current, Any Pin Except Supplies IIN Analog Input Voltage (AINL, AINR, CKS1 pins) VINA -0.3 Digital Input Voltage (Note 3) VIND -0.3 Ambient Temperature (powered applied) Ta -40 Storage Temperature Tstg -65 Note 1. All voltages with respect to ground. Note 2. AGND and DGND must be connected to the same analog ground plane. Note 3. DIF, PDN, SCLK, MCLK, LRCK, CKS0 and CKS2 pins max 6.0 6.0 10 VA+0.3 VD+0.3 85 150 Units V V mA V V C C WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (AGND, DGND=0V; Note 1) Parameter Symbol Power Supplies Analog VA (Note 4) Digital: Normal Speed VD Double/Quad Speed VD Note 4. The power up sequence between VA and VD is not critical. min 4.5 2.7 3.0 typ 5.0 3.3 3.3 max 5.5 3.6 3.6 Units V V V WARNING: AKM assumes no responsibility for the usage beyond the conditions in this datasheet. MS0579-E-00 2006/12 -4- ASAHI KASEI [AK5386] ANALOG CHARACTERISTICS (Ta=25C; VA=5.0V, VD=3.3V; AGND=DGND=0V; fs=48kHz, 96kHz, 192kHz; SCLK=64fs; Signal Frequency=1kHz; 24bit Data; Measurement frequency=20Hz 20kHz at fs=48kHz, 40Hz 40kHz at fs=96kHz, 40Hz 40kHz at fs=192kHz; unless otherwise specified) Parameter min typ max Units ADC Analog Input Characteristics: Resolution 24 Bits Input Voltage (Note 5) 2.7 3.0 3.3 Vpp S/(N+D) fs=48kHz 86 96 dB -1dBFS BW=20kHz 47 dB -60dBFS fs=96kHz 86 92 dB -1dBFS BW=40kHz 42 dB -60dBFS fs=192kHz 90 dB -1dBFS BW=40kHz 42 dB -60dBFS DR (-60dBFS with A-weighted) 102 110 dB S/N (A-weighted) 102 110 dB Input Resistance 4 6 k Interchannel Isolation 95 115 dB Interchannel Gain Mismatch 0.1 0.5 dB Gain Drift 100 ppm/C Power Supply Rejection (Note 6) 50 dB Power Supplies Power Supply Current Normal Operation (PDN pin = "H") VA 20 30 VD (fs=48kHz) 7 11 VD (fs=96kHz) 10 15 VD (fs=192kHz) 10 15 Power down mode (PDN pin = "L") (Note 7) VA+VD 10 100 Note 5. This value is the full scale (0dB) of the input voltage. Input voltage is proportional to VA voltage. Vin = 0.6 x VA (Vpp). Note 6. PSR is applied to VA and VD with 1kHz, 50mVpp. Note 7. All digital input pins are held VD or DGND. MS0579-E-00 mA mA mA mA A 2006/12 -5- ASAHI KASEI [AK5386] FILTER CHARACTERISTICS (fs=48kHz) (Ta=-40 85C; VA=4.5 5.5V; VD=2.7 3.6V) Parameter Symbol min typ ADC Digital Filter (Decimation LPF): Passband (Note 8) 0.02dB PB 0 221. -0.1dB 22.3 -0.2dB 23.5 -3.0dB Stopband SB 26.5 Passband Ripple PR Stopband Attenuation SA 80 Group Delay Distortion 0 GD Group Delay (Note 9) GD 29.4 ADC Digital Filter (HPF): Frequency Response (Note 8) -3dB FR 1.0 6.5 -0.1dB FILTER CHARACTERISTICS (fs=96kHz) (Ta=-40 85C; VA=4.5 5.5V; VD=3.0 3.6V) Parameter Symbol min typ ADC Digital Filter (Decimation LPF): Passband (Note 8) 0.02dB PB 0 44.3 -0.1dB 44.6 -0.2dB 47.0 -3.0dB Stopband SB 53.0 Passband Ripple PR Stopband Attenuation SA 80 Group Delay Distortion 0 GD Group Delay (Note 9) GD 29.4 ADC Digital Filter (HPF): Frequency Response (Note 8) -3dB FR 2.0 13.0 -0.1dB MS0579-E-00 max Units 21.768 0.005 - kHz kHz kHz kHz kHz dB dB s 1/fs - Hz Hz max Units 43.536 0.005 - kHz kHz kHz kHz kHz dB dB s 1/fs - Hz Hz 2006/12 -6- ASAHI KASEI [AK5386] FILTER CHARACTERISTICS (fs=192kHz) (Ta=-40 85C; VA=4.5 5.5V; VD=3.0 3.6V) Parameter Symbol min typ max Units ADC Digital Filter (Decimation LPF): Passband (Note 8) 0.1dB PB 0 43.8 kHz 52.9 kHz -0.2dB 90.1 kHz -3.0dB Stopband SB 112 kHz Passband Ripple PR dB 0.005 Stopband Attenuation SA 72 dB Group Delay Distortion 0 GD s Group Delay (Note 9) GD 16.5 1/fs ADC Digital Filter (HPF): Frequency Response (Note 8) -3dB FR 4.0 Hz 26.0 Hz -0.1dB Note 8. The passband and stopband frequencies scale with fs. For example, PB (0.02dB) at fs=48kHz is 0.4535 x fs. The reference frequency of these response is 1kHz. Note 9. The calculated delay time induced by digital filtering. This time is from the input of an analog signal to the setting of 24bit data both channels to the ADC output register for ADC. DC CHARACTERISTICS (Ta=-40 85C; VA=4.5 5.5V; VD=2.7 3.6V at Normal Speed, VD=3.0 3.6V at Double/Quad Speed) Parameter Symbol min typ max High-Level Input Voltage VIH 70%VD Low-Level Input Voltage VIL 30%VD High-Level Output Voltage (Iout=-1mA) VOH VD-0.5 Low-Level Output Voltage (Iout=1mA) VOL 0.5 Input Leakage Current Iin 10 MS0579-E-00 Units V V V V A 2006/12 -7- ASAHI KASEI [AK5386] SWITCHING CHARACTERISTICS (Normal Speed) (Ta=-40 85C; VA=4. 5 5.5V; VD=2.7 3.6V; CL=20pF) Parameter Symbol min typ Master Clock Timing Frequency: 512fs fCLK 4.096 768fs fCLK 6.144 Pulse Width Low tCLKL 0.4/fCLK Pulse Width High tCLKH 0.4/fCLK LRCK Frequency: 512fs 768fs Duty Cycle max Units 27.648 36.864 - MHz MHz ns ns fs fs 8 8 45 - 50 54 48 55 - kHz kHz % % Slave mode Master mode Audio Interface Timing Slave mode SCLK Period SCLK Pulse Width Low Pulse Width High LRCK Edge to SCLK "" (Note 10) SCLK "" to LRCK Edge (Note 10) LRCK to SDTO (MSB) (Except I2S mode) SCLK "" to SDTO Master mode SCLK Frequency SCLK Duty SCLK "" to LRCK SCLK "" to SDTO tSCK tSCKL tSCKH tLRSH tSHLR tLRS tSSD 1/128fs 60 60 20 20 - - 40 40 ns ns ns ns ns ns ns fSCK dSCK tMSLR tSSD -20 -20 64fs 50 - 40 40 Hz % ns ns Reset Timing PDN Pulse Width (Note 11) PDN "" to SDTO valid at Slave Mode (Note 12) PDN "" to SDTO valid at Master Mode (Note 12) tPD tPDV tPDV 150 - 4132 4129 - ns 1/fs 1/fs MS0579-E-00 2006/12 -8- ASAHI KASEI [AK5386] SWITCHING CHARACTERISTICS (Double / Quad Speed) (Ta=-40 85C; VA=4. 5 5.5V; VD=3.0 3.6V; CL=20pF) Parameter Symbol min typ Master Clock Timing Frequency: 128fs, 256fs fCLK 13.824 192fs, 384fs fCLK 18.432 Pulse Width Low tCLKL 0.4/fCLK Pulse Width High tCLKH 0.4/fCLK - max Units 27.648 36.864 - MHz MHz ns ns LRCK Frequency: Duty Cycle Double Speed:256fs fs 54 - 108 kHz 384fs - 96 kHz fs 48 Quad Speed: 128fs fs 108 - 216 kHz 192fs fs 96 45 - 50 192 55 - kHz % % tSCK tSCK tSCKL tSCKH tLRSH tSHLR tLRS tSSD 1/128fs 1/64fs 33 33 20 20 - - 20 20 ns ns ns ns ns ns ns ns fSCK dSCK tMSLR tSSD -20 -20 64fs 50 - 20 20 Hz % ns ns 4132 4129 - ns 1/fs 1/fs Slave mode Master mode Audio Interface Timing Slave mode SCLK Period: Double Speed Quad Speed SCLK Pulse Width Low Pulse Width High LRCK Edge to SCLK "" (Note 10) SCLK "" to LRCK Edge (Note 10) LRCK to SDTO (MSB) (Except I2S mode) SCLK "" to SDTO Master mode SCLK Frequency SCLK Duty SCLK "" to LRCK SCLK "" to SDTO Reset Timing tPD PDN Pulse Width (Note 11) 150 tPDV PDN "" to SDTO valid at Slave Mode (Note 12) tPDV PDN "" to SDTO valid at Master Mode (Note 12) Note 10. SCLK rising edge must not occur at the same time as LRCK edge. Note 11. The AK5386 can be reset by bringing the PDN pin = "L" Note 12. This cycle is the number of LRCK rising edges from the PDN pin = "H". MS0579-E-00 2006/12 -9- ASAHI KASEI [AK5386] Timing Diagram 1/fCLK VIH MCLK VIL tCLKH tCLKL 1/fs VIH LRCK VIL tSCK VIH SCLK VIL tSCKH tSCKL Clock Timing VIH LRCK VIL tSHLR tLRSH VIH SCLK VIL tSSD tLRS SDTO 50%VD Audio Interface Timing (Slave mode) MS0579-E-00 2006/12 - 10 - ASAHI KASEI [AK5386] LRCK 50%VD tMSLR dSCK SCLK 50%VD tSSD SDTO 50%VD Audio Interface Timing (Master mode) VIH PDN VIL tPD tPDV SDTO 50%VD Power Down & Reset Timing MS0579-E-00 2006/12 - 11 - ASAHI KASEI [AK5386] OPERATION OVERVIEW System Clock MCLK, SCLK and LRCK (fs) clocks are required in slave mode. The LRCK clock input must be synchronized with MCLK, however the phase is not critical. Table 1 shows the relationship of typical sampling frequency and the system clock frequency. MCLK frequency, SCLK frequency, HPF (ON or OFF) and master/slave are selected by CKS2-0 pins as shown in Table 3. When MCLK is 192fs, 384fs or 768fs, the sampling frequency does not support variable pitch. All external clocks (MCLK, SCLK and LRCK) must be present unless PDN pin = "L". If these clocks are not provided, the AK5386 may draw excess current due to its use of internal dynamically refreshed logic. If the external clocks are not present, place the AK5386 in power-down mode (PDN pin = "L"). In master mode, the master clock (MCLK) must be provided unless PDN pin = "L". fs 32kHz 44.1kHz 48kHz 96kHz 192kHz 128fs N/A N/A N/A N/A 24.576MHz MCLK 192fs 256fs 384fs N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 24.576MHz 36.864MHz 36.864MHz N/A N/A Table 1. System Clock Example Mode Sampling Frequency 8kHz fs 54kHz Normal Speed 8kHz fs 48kHz 54kHz < fs 108kHz Double Speed 48kHz < fs 96kHz 108kHz < fs 216kHz Quad Speed 96kHz < fs 192kHz Table 2. Sampling Frequency Range CKS2 pin CKS1 pin CKS0 pin L L L L L H L L H H H H H H L L H H L H L H L H HPF Master/Slave 512fs 16.384MHz 22.5792MHz 24.576MHz N/A N/A 768fs 24.576MHz 33.8688MHz 36.864MHz N/A N/A MCLK 512fs 768fs 256fs 384fs 128fs 192fs MCLK 128/192fs (Quad Speed) ON Slave 256/384fs (Double Speed) 512/768fs (Normal Speed) 128/192fs (Quad Speed) OFF Slave 256/384fs (Double Speed) 512/768fs (Normal Speed) ON Master 256fs (Double Speed) ON Master 512fs (Normal Speed) ON Master 128fs (Quad Speed) ON Master 192fs (Quad Speed) ON Master 384fs (Double Speed) ON Master 768fs (Normal Speed) Table 3. Mode Select SCLK 48fs or 32fs (Note 13) 48fs or 32fs (Note 13) 64fs 64fs 64fs 64fs 64fs 64fs Note 13. SDTO outputs 16bit data at SCLK=32fs. MS0579-E-00 2006/12 - 12 - ASAHI KASEI [AK5386] Audio Interface Format Two kinds of data formats can be chosen with the DIF pin (Table 4). In both modes, the serial data is in MSB first, 2's complement format. The SDTO is clocked out on the falling edge of SCLK. The audio interface supports both master and slave modes. In master mode, SCLK and LRCK are output with the SCLK frequency fixed to 64fs and the LRCK frequency fixed to 1fs. Mode 0 1 DIF pin L H SDTO LRCK SCLK 24bit, MSB justified H/L 48fs or 32fs 24bit, I2S Compatible L/H 48fs or 32fs Table 4. Audio Interface Format Figure Figure 1 Figure 2 LRCK 0 1 2 31 0 1 2 20 21 22 23 24 20 21 22 23 24 31 0 1 SCLK(64fs) SDTO(o) 23 22 4 3 2 1 0 23 22 4 3 2 1 0 23 23:MSB, 0:LSB Lch Data Rch Data Figure 1. Mode 0 Timing LRCK 0 1 2 3 21 22 23 24 25 0 1 2 21 22 23 24 25 0 1 SCLK(64fs) SDTO(o) 23 22 4 3 2 1 0 23 22 4 3 2 1 0 23:MSB, 0:LSB Lch Data Rch Data Figure 2. Mode 1 Timing Digital High Pass Filter The ADC has a digital high pass filter for DC offset cancellation. The cut-off frequency of the HPF is 1.0Hz (@fs=48kHz) and scales with sampling rate (fs). HPF is controlled by CKS2-0 pins (Table 3). If HPF setting (ON/OFF) is changed at operating, click noise occurs by changing DC offset. It is recommended that HPF setting is changed at PDN pin = "L". MS0579-E-00 2006/12 - 13 - ASAHI KASEI [AK5386] Power down The AK5386 is placed in the power-down mode by bringing PDN pin "L" and the digital filter is also reset at the same time. This reset should always be done after power-up. In the power-down mode, the VCOM are AGND level. An analog initialization cycle starts after exiting the power-down mode. Therefore, the output data SDTO becomes available after 4129 cycles of LRCK clock in master mode or 4132 cycles of LRCK clock in slave mode. During initialization, the ADC digital data outputs of both channels are forced to a 2's complement "0". The ADC outputs settle in the data corresponding to the input signals after the end of initialization (Settling approximately takes the group delay time). (1) PDN Internal State Normal Operation Power-down Initialize Normal Operation GD (2) GD A/D In (Analog) A/D Out (Digital) Clock In MCLK,LRCK,SCLK (3) "0"data Idle Noise "0"data Idle Noise (4) Notes: (1) 4132/fs in slave mode and 4129/fs in master mode. (2) Digital output corresponding to analog input has the group delay (GD). (3) A/D outputs "0" data at the power-down state. (4) When the external clocks (MCLK, SCLK and LRCK) are stopped, the AK5386 should be in the power-down state. Figure 3. Power-down/up sequence example System Reset The AK5386 should be reset once by bringing PDN pin "L" after power-up. In slave mode, the internal timing starts clocking by the rising edge (falling edge at mode 1) of LRCK after exiting from reset and power down state by MCLK. The AK5386 is power down state until LRCK is input. In master mode, the internal timing starts when MCLK is input. MS0579-E-00 2006/12 - 14 - ASAHI KASEI [AK5386] SYSTEM DESIGN Figure 4 shows the system connection diagram. An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. Rch In 1 AINR CKS0 16 Lch In 2 AINL CKS2 15 2.2u 3 CKS1 DIF 14 4 VCOM PDN 13 5 AGND Analog 5V + 10u Digital 3.3V + 10u 0.1u 0.1u AK5386 Mode Control Reset SCLK 12 6 VA MCLK 11 7 VD LRCK 10 8 DGND SDTO 9 Audio Controller Analog Ground System Ground Notes: - AGND and DGND of the AK5386 should be distributed separately from the ground of external digital devices (MPU, DSP etc.). - All digital input pins should not be left floating. - The CKS1 pin should be connected to VA or AGND. Figure 4. Typical Connection Diagram Digital Ground Analog Ground System Controller 1 AINR CKS0 16 2 AINL CKS2 15 3 CKS1 DIF 14 4 VCOM PDN 13 5 AGND SCLK 12 6 VA MCLK 11 7 VD LRCK 10 8 DGND SDTO 9 AK5386 Figure 5. Ground Layout Note: AGND and DGND must be connected to the same analog ground plane. MS0579-E-00 2006/12 - 15 - ASAHI KASEI [AK5386] 1. Grounding and Power Supply Decoupling The AK5386 requires careful attention to power supply and grounding arrangements. To minimize coupling from digital noise, decoupling capacitors should be connected to VA and VD respectively. VA is supplied from the analog supply in the system, and VD is supplied from the digital supply in the system. The power up sequence is not critical between VA and VD. AGND and DGND of the AK5386 must be connected to one analog ground plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling capacitors should be as near to the AK5386 as possible, with the small value ceramic capacitor being the nearest. 2. Voltage Reference The voltage input to VA sets the analog input range. VCOM are 50%VA and normally connected to AGND with a 0.1F ceramic capacitor. A capacitor 2.2F attached to VCOM pin eliminates the effects of high frequency noise. No load current may be drawn from these pins. All signals, especially clocks, should be kept away from the VA and VCOM pins in order to avoid unwanted coupling into the AK5386. 3. Analog Inputs The ADC inputs are single-ended and internally biased to the common voltage (50%VA) with 6k (typ, @fs=48kHz, 96kHz, 192kHz) resistance. The input signal range scales with the supply voltage and nominally 0.6xVA Vpp (typ). The ADC output data format is 2's complement. The internal HPF removes the DC offset. The AK5386 samples the analog inputs at 128fs (@ fs=48kHz), 64fs (@ fs=96kHz) or 32fs(@ fs=192kHz). The digital filter rejects noise above the stop band except for multiples of 64fs or 32fs. The AK5386 includes an anti-aliasing filter (RC filter) to attenuate a noise around 128fs, 64fs or 32fs. MS0579-E-00 2006/12 - 16 - ASAHI KASEI [AK5386] PACKAGE 16pin TSSOP (Unit: mm) 5.0 16 1.10max 9 4.4 6.40.2 A 1 0.220.1 8 0.170.05 0.65 0.10.1 0.50.2 Detail A Seating Plane 0.10 010 Material & Lead finish Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy Cu Solder (Pb free) plate MS0579-E-00 2006/12 - 17 - ASAHI KASEI [AK5386] MARKING AKM 5386VT XXYYY 1) Pin #1 indication 2) Date Code: XXYYY (5 digits) XX: Lot# YYY: Date Code 3) Marketing Code: 5386VT Revision History Date (YY/MM/DD) 06/12/13 Revision 00 Reason First Edition Page Contents IMPORTANT NOTICE * These products and their specifications are subject to change without notice. Bef ore considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or dev ices or systems containing them, may require an export license or other off icial approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representativ e Director of AKM. As used here: a. A hazard related dev ice or system is one designed or intended for life support or maintenance of saf ety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to f unction or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. b. A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the saf ety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the abov e content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless f rom any and all claims arising from the use of said product in the absence of such notification. MS0579-E-00 2006/12 - 18 -