2 MHz, Synchronous Boost DC-to-DC Converter ADP1607 Data Sheet FEATURES GENERAL DESCRIPTION Up to 96% efficiency 0.8 V to VOUT input voltage range Low 0.9 V input start-up voltage 1.8 V to 3.3 V output voltage range 23 A quiescent current Fixed PWM and light load PFM mode options Synchronous rectification True shutdown output Isolation Internal soft start, compensation, and current limit 2 mm x 2 mm, 6-lead LFCSP Compact solution size The ADP1607 is a high efficiency, synchronous, fixed frequency, step-up dc-to-dc switching converter with an adjustable output voltage between 1.8 V and 3.3 V for use in portable applications. The 2 MHz operating frequency enables the use of small footprint, low profile external components. Additionally, the synchronous rectification, internal compensation, internal fixed current limit, and current mode architecture allow for excellent transient response and a minimal external part count. Other key features include fixed PWM and light load PFM mode options, true output isolation, thermal shutdown (TSD), and logic controlled enable. Available in a lead-free, thin, 6-lead LFCSP package, the ADP1607 is ideal for providing efficient power conversion in portable devices. APPLICATIONS 1-cell and 2-cell alkaline and NiMH/NiCd powered devices Portable audio players, instruments, and medical devices Solar cell applications Miniature hard disk power supplies Power LED status indicators TYPICAL APPLICATION CIRCUIT L 2.2H INPUT VOLTAGE 0.8V TO VOUT ADP1607 1 ADJUSTABLE OUTPUT VOLTAGE 1.8V TO 3.3V SW 5 VIN CIN 10F VOUT 6 R1 2 EN GND 4 FB 3 R2 COUT 10F 10276-001 ON OFF Figure 1. Rev. C Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2012-2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADP1607 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Overview ..................................................................................... 10 Applications ....................................................................................... 1 Enable/Shutdown ....................................................................... 10 General Description ......................................................................... 1 Modes of Operation ................................................................... 10 Typical Application Circuit ............................................................. 1 Internal Control Features .......................................................... 11 Revision History ............................................................................... 2 Applications Information .............................................................. 12 Specifications..................................................................................... 3 Setting the Output Voltage ........................................................ 12 Absolute Maximum Ratings ............................................................ 4 Inductor Selection ...................................................................... 12 Thermal Operating Ranges ......................................................... 4 Choosing the Input Capacitor .................................................. 13 Thermal Resistance ...................................................................... 4 Choosing the Output Capacitor ............................................... 13 ESD Caution .................................................................................. 4 Layout Guidelines ........................................................................... 14 Pin Configuration and Function Descriptions ............................. 5 Outline Dimensions ....................................................................... 15 Typical Performance Characteristics ............................................. 6 Ordering Guide .......................................................................... 15 Theory of Operation ...................................................................... 10 REVISION HISTORY 12/13--Rev. B to Rev. C Changes to Figure 21 ........................................................................ 9 7/13--Rev. A to Rev. B Changes to Captions for Figure 22 and Figure 23 ........................ 9 Changed Synchronous Rectification Section .............................. 11 12/12--Rev. 0 to Rev. A Changes to Features Section............................................................ 1 Changed TJ to TA in Specifications Section................................... 3 Changed Figure 6, Figure 7, and Figure 8 Captions..................... 6 Changes to Table 5 .......................................................................... 12 Changes to Choosing the Output Capacitor Section ................. 13 10/12--Revision 0: Initial Version Rev. C | Page 2 of 16 Data Sheet ADP1607 SPECIFICATIONS VIN = VEN = 1.2 V, VOUT = 3.3 V at TA = -40C to +85C for minimum/maximum specifications, and TA = 25C for typical specifications, unless otherwise noted. 1 Table 1. Parameter SUPPLY Minimum Start-Up Voltage 2 Operating Input Voltage Range 3 Shutdown Current Quiescent Current Soft Start Time SWITCH Current Limit NMOS On Resistance PMOS On Resistance SW Leakage Current OSCILLATOR Switching Frequency Maximum Duty Cycle OUTPUT VOUT Range FB Pin Voltage FB Pin Current EN/MODE LOGIC Input Voltage Threshold Low Input Voltage Threshold High EN/MODE Leakage Current THERMAL SHUTDOWN 5 Thermal Shutdown Threshold Thermal Shutdown Hysteresis Symbol VIN IQSD ICL RDSON_N RDSON_P Test Conditions/Comments Min RMIN = 22 0.9 0.8 Max Unit 0.06 VOUT 0.67 V V A 23 23 29 40 A A 6 6 1.3 11 14.6 A A ms 0.8 1 116 155 0.18 1.3 165 225 2 A m m A 1.8 85 2 90 2.2 MHz % 3.3 1.2842 0.25 V V A 0.25 V V A VEN = GND, VOUT = GND, TA = -40C to +45C 4 Nonswitching, measured on VOUT, auto operating mode part only TA = -40C to +45C TA = -40C to +85C Measured on VIN TA = -40C to +45C TA = -40C to +85C ISW = 500 mA ISW = 500 mA VSW = 1.2 V, VOUT = 0 V, TA = -40C to +45C4 fSW DMAX VOUT VFB IFB Typ PWM mode VFB = 1.26 V VIL VIH 1.8 1.2338 1.259 0.1 0.8 VEN = GND or VIN, VOUT = 0 V 0.001 150 15 0.25 C C All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC). Specifications are subject to change without notice. Guaranteed by design, but not production tested. VIN can never exceed VOUT once the ADP1607 is enabled. 3 Minimum value is characterized by design. Maximum value is characterized on the bench. 4 This parameter is the semiconductor leakage current. The semiconductor leakage current doubles with every 10C increase in temperature. The maximum limit follows the same trend over temperature. 5 Thermal shutdown protection is only active in PWM mode. 1 2 Rev. C | Page 3 of 16 ADP1607 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VIN, VOUT to GND FB to GND EN, SW to GND (when VIN VOUT) EN, SW to GND (when VIN < VOUT) EPAD to GND Operating Ambient Temperature Range Operating Junction Temperature Range Storage Temperature Range Soldering Conditions Rating -0.3 V to +3.6 V -0.3 V to +1.4 V -0.3 V to VIN + 0.3 V -0.3 V to VOUT + 0.3 V -0.3 V to + 0.3 V -40C to +85C -40C to +90C -65C to +150C JEDEC J-STD-020 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Absolute maximum ratings apply individually only, not in combination. The junction temperature TJ of the device is dependent on the ambient temperature (TA), the power dissipation of the device (PD), and the junction-to-ambient thermal resistance of the package (JA). Maximum junction temperature (TJ) is calculated from the ambient temperature (TA) and power dissipation (PD) using the following formula: TJ = TA + (PD x JA) THERMAL RESISTANCE Junction-to-ambient thermal resistance (JA) of the package is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. The junction-to-ambient thermal resistance is highly dependent on the application and board layout. In applications where high maximum power dissipation exists, attention to thermal board design is required. The value of JA may vary, depending on PCB material, layout, and environmental conditions. JA and JC (junction to case) are determined according to JESD51-9 on a 4-layer PCB with natural convection cooling and the exposed pad soldered to the board with thermal vias. Table 3. THERMAL OPERATING RANGES The ADP1607 can be damaged when the junction temperature limits are exceeded. The maximum operating junction temperature (TJ(MAX)) takes precedence over the maximum operating ambient temperature (TA(MAX)). Monitoring ambient temperature does not guarantee that the junction temperature (TJ) is within the specified temperature limits. Package Type 6-Lead LFCSP ESD CAUTION In applications with high power dissipation and poor PCB thermal resistance, the maximum ambient temperature may need to be derated. In applications with moderate power dissipation and low PCB thermal resistance, the maximum ambient temperature can exceed the maximum limit as long as the junction temperature is within specification limits. Rev. C | Page 4 of 16 JA 66.06 JC 4.3 Unit C/W Data Sheet ADP1607 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS VIN 1 6 VOUT ADP1607 FB 3 TOP VIEW (Not to Scale) 7 EPAD 5 SW 4 GND NOTES 1. CONNECT THE EXPOSED PAD TO GND. 10276-002 EN 2 Figure 2. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 Mnemonic VIN EN FB GND SW VOUT EPAD Description Analog and Power Supply Pin. Shutdown Control Pin. Drive EN high to turn on the synchronous boost, drive EN low to turn it off. Output Voltage Feedback Pin. Analog and Power Ground Pin. Drain Connection for NMOS and PMOS Power Switches. Output Voltage and Source Connection of PMOS Power Switch. Exposed Pad. Connect to GND. Rev. C | Page 5 of 16 ADP1607 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VIN = 1.2 V, VOUT = 3.3 V, L = 2.2 H (DCRMAX = 66 m, VLF302512MT-2R2M), CIN = 10 F, COUT = 10 F (10 V, 20%, LMK107BJ106MALT), VEN = VIN, and TA = 25C, unless otherwise noted. 1.84 VOUT = 1.8V VIN = 0.8V VIN = 1.2V VIN = 1.5V VOUT = 1.8V 90 1.83 OUTPUT VOLTAGE (V) 80 60 50 40 30 20 10 100 1000 LOAD CURRENT (mA) 1.78 0.1 2.56 VOUT = 2.5V 100 OUTPUT VOLTAGE (V) 2.54 70 60 50 40 30 0 0.1 1 10 100 1000 LOAD CURRENT (mA) 2.52 2.51 2.50 2.48 2.47 0.1 10276-004 10 2.53 2.49 VIN = 0.8V VIN = 1.2V VIN = 1.5V VIN = 2.2V 20 1 10 100 Figure 7. Auto Mode Output Voltage Load Regulation, VOUT = 2.5 V 3.40 VOUT = 3.3V VOUT = 3.3V VIN = 0.8V VIN = 1.2V VIN = 1.5V VIN = 2.2V VIN = 3.0V 90 3.38 OUTPUT VOLTAGE (V) 80 60 50 40 30 VIN = 0.8V VIN = 1.2V VIN = 1.5V VIN = 2.2V VIN = 3.0V 0 0.1 1 10 100 1000 LOAD CURRENT (mA) 3.36 3.34 3.32 3.30 3.28 10276-005 EFFICIENCY (%) 70 10 1000 LOAD CURRENT (mA) Figure 4. Auto Mode Efficiency vs. Load Current, VOUT = 2.5 V 20 1000 VIN = 0.8V VIN = 1.2V VIN = 1.5V VIN = 2.2V VOUT = 2.5V 2.55 80 EFFICIENCY (%) 10 Figure 6. Auto Mode Output Voltage Load Regulation, VOUT = 1.8 V 90 100 1 LOAD CURRENT (mA) Figure 3. Auto Mode Efficiency vs. Load Current, VOUT = 1.8 V 100 1.80 10276-006 1 10276-003 0 0.1 1.81 1.79 VIN = 0.8V VIN = 1.2V VIN = 1.5V 10 1.82 10276-007 EFFICIENCY (%) 70 Figure 5. Auto Mode Efficiency vs. Load Current, VOUT = 3.3 V 3.26 0.1 1 10 100 1000 LOAD CURRENT (mA) Figure 8. Auto Mode Output Voltage Load Regulation, VOUT = 3.3 V Rev. C | Page 6 of 16 10276-008 100 ADP1607 270 30 ISW = 500mA 240 PMOS RDSON (m) 27 24 21 TA = -40C TA = +25C TA = +45C TA = +85C 15 1.8 3.3 2.8 2.3 INPUT VOLTAGE (V) 210 TA = +90C 180 TA = +25C 150 TA = -40C 120 1.8 3.3 2.8 OUTPUT VOLTAGE (V) Figure 12. PMOS Drain-to-Source On Resistance Figure 9. Nonswitching PFM Mode Quiescent Current vs. Input Voltage 1200 5 TA = -40C TA = +25C TA = +45C TA = +90C VOUT = 3.3V VOUT = 2.5V 1100 VOUT = 1.8 V CURRENT LIMIT (mA) 4 3 2 1000 900 800 1 1.4 1.9 2.4 700 0.8 10276-010 0 0.9 2.9 INPUT VOLTAGE (V) 1.8 1.3 2.3 3.3 2.8 INPUT VOLTAGE (V) 10276-013 SHUTDOWN CURRENT (A) 2.3 10276-012 18 10276-009 NONSWITCHING VOUT QUIESCENT CURRENT (A) Data Sheet Figure 13. Switch Current Limit vs. Input Voltage Figure 10. Shutdown Current vs. Input Voltage 140 170 ISW = 500mA 120 LOAD CURRENT (mA) TA = +90C 140 125 TA = +25C 100 PWM OPERATION 80 60 40 110 20 PFM OPERATION 95 1.8 2.3 2.8 OUTPUT VOLTAGE (V) 3.3 0 0.8 1.0 1.2 1.4 1.6 VOUT = 2.5V 1.8 2.0 INPUT VOLTAGE (V) Figure 14. Auto Mode Transition Thresholds Figure 11. NMOS Drain-to-Source On Resistance Rev. C | Page 7 of 16 2.2 10276-014 TA = -40C 10276-011 NMOS RDSON (m) 155 ADP1607 Data Sheet 88.4 VIN = 1.2V VOUT = 3.3V ILOAD = 1mA TO 50mA MAXIMUM DUTY CYCLE (%) 88.0 1 TA = +90C TA = -40C 87.6 OUTPUT VOLTAGE (100mV/DIV) AC-COUPLED 87.2 TA = +25C LOAD CURRENT (50mA/DIV) 86.8 2.3 2.8 3.3 OUTPUT VOLTAGE (V) TIME (200s/DIV) 10276-015 86.4 1.8 Figure 15. Maximum Duty Cycle vs. Output Voltage 10276-018 4 Figure 18. PFM Mode Load Transient Response (Auto Mode Part) 2.04 VIN = 1.2V VOUT = 3.3V ILOAD = 50mA TO 100mA FREQUENCY (MHz) 2.02 1 VOUT = 3.3V OUTPUT VOLTAGE (100mV/DIV) AC-COUPLED 2.00 VOUT = 2.5V 1.98 VOUT = 1.8V 1.96 -10 20 50 TIME (200s/DIV) 10276-016 1.94 -40 80 TEMPERATURE (C) Figure 19. PWM Mode Load Transient Response (Fixed PWM Mode Part) Figure 16. Frequency vs. Temperature 1000 VIN = 1.2V VOUT = 3.3V RLOAD = 3.3k VOUT = 2.5V VOUT = 3.3V VOUT = 1.8 V 700 OUTPUT VOLTAGE (1V/DIV) SW PIN VOLTAGE (2V/DIV) 1 600 500 2 INDUCTOR CURRENT (200mA/DIV) 400 300 EN PIN VOLTAGE (1V/DIV) 100 0 0.8 3 1.3 1.8 2.3 2.8 INPUT VOLTAGE (V) 3.3 TIME (200s/DIV) Figure 20. Startup, RLOAD =3.3 k Figure 17. Maximum Output Current vs. Input Voltage Rev. C | Page 8 of 16 10276-020 4 200 10276-017 MAXIMUM OUTPUT CURRENT (mA) 900 800 10276-019 LOAD CURRENT (50mA/DIV) 4 Data Sheet ADP1607 VIN = 1.2V VOUT = 3.3V RLOAD = 33 OUTPUT VOLTAGE (20mV/DIV) AC COUPLED OUTPUT VOLTAGE (1V/DIV) 1 SW PIN VOLTAGE (2V/DIV) SW PIN VOLTAGE (2V/DIV) 1 2 2 INDUCTOR CURRENT (500mA/DIV) 10276-021 EN PIN VOLTAGE (1V/DIV) VIN = 1.2V VOUT = 3.3V ILOAD = 100mA 3 TIME (200s/DIV) 4 TIME (400ns/DIV) Figure 21. Startup, RLOAD = 33 Figure 23. Typical PWM Mode Operation, ILOAD = 100 mA OUTPUT VOLTAGE (100mV/DIV) AC COUPLED 1 SW PIN VOLTAGE (2V/DIV) 2 INDUCTOR CURRENT (200mA/DIV) VIN = 1.2V VOUT = 3.3V ILOAD = 10mA 10276-022 4 TIME (10s/DIV) INDUCTOR CURRENT (100mA/DIV) Figure 22. Typical PFM Mode Operation, ILOAD = 10 mA Rev. C | Page 9 of 16 10276-023 4 ADP1607 Data Sheet THEORY OF OPERATION L1 VIN SW 5 VIN 1 CIN BULK CONTROL VOUT VDD VIN VSEL VSEL + VOUT R1 ERROR AMPLIFIER VOUT 6 CURRENT SENSING COUT P FB OSCILLATOR 3 R2 A + PWM COMPARATOR PMOS BULK CONTROL P DRIVER VREF RCOMP CCOMP QP S CURRENT-LIMIT COMPARATOR N DRIVER SW N QN R SOFT START RP RESET ZERO CROSS TSD COMPARATOR TSENSE TREF SHUTDOWN PFM COMPARATOR VREF 2 4 GND 10276-033 EN AGND PFM CONTROL ON OFF Figure 24. Block Diagram OVERVIEW MODES OF OPERATION The ADP1607 is a high efficiency, synchronous, fixed frequency, step-up dc-to-dc switching converter with an adjustable output voltage between 1.8 V and 3.3 V for use in portable applications. The ADP1607 is available in a fixed PWM mode only option for noise sensitive applications or in an auto PFM-to-PWM transitioning mode option to optimize power at light loads. The 2 MHz operating frequency enables the use of small footprint, low profile external components. Additionally, the synchronous rectification, internal compensation, internal fixed current limit, and current-mode architecture allow for excellent transient response and a minimal external part count. Other key features include fixed PWM and light load PFM mode options, true output isolation, thermal shutdown (TSD), and logic controlled enable. ENABLE/SHUTDOWN The EN input turns the ADP1607 on or off. Connect EN to GND or logic low to shut down the part and reduce the current consumption to 0.06 A (typical). Connect EN to VIN or logic high to enable the part. Do not exceed VIN. Do not leave this pin floating. Pulse-Width Modulation (PWM) Mode The PWM version of the ADP1607 utilizes a current-mode PWM control scheme to force the part to maintain a fixed 2 MHz fixed frequency while regulating the output voltage over all load conditions. The auto mode version of the ADP1607 operates in PWM for higher load currents. In PWM, the output voltage is monitored at the FB pin through the external resistive voltage divider. The voltage at FB is compared to the internal 1.259 V reference by the internal error amplifier. This currentmode PWM regulation system allows fast transient response and tight output voltage regulation. PWM mode operation results in lower efficiencies than PFM mode at light loads. Auto Mode Auto mode is a power-saving feature that forces the auto version of the ADP1607 to switch between PFM and PWM in response to output load changes. The auto version of the ADP1607 Rev. C | Page 10 of 16 Data Sheet ADP1607 operates in PFM mode for light load currents and switches to PWM mode for medium and heavy load currents. INTERNAL CONTROL FEATURES Pulse Frequency Modulation (PFM) While in shutdown, the ADP1607 manages the voltage of the bulk of the PMOS to force it off and internally isolate the path from the input to output. This allows the output to drop to ground, reducing the current consumption of the application in shutdown. Input to Output Isolation When the auto mode version of the ADP1607 is operating under light load conditions, the effective switching frequency and supply current are decreased and varied using PFM to regulate the output voltage. This results in improved efficiencies and lower quiescent currents. In PFM mode, the converter only switches when necessary to keep the output voltage between the PFM comparator high output voltage threshold and the lower sleep mode exit voltage threshold. Switching stops when the upper PFM limit is reached and resumes when the lower sleep mode exit threshold is reached. When VOUT exceeds the upper PFM threshold, switching stops and the part enters sleep mode. In sleep mode, the ADP1607 is mostly shut down, significantly reducing the quiescent current. The output voltage is then discharged by the load until the output voltage reaches the lower sleep mode exit threshold. After crossing the lower sleep mode exit threshold, switching resumes and the process repeats. Mode Transition The auto mode version of the ADP1607 switches automatically between PFM and PWM modes to maintain optimal efficiency. Switching to PFM allows the converter to save power by supplying the lighter load current with fewer switching cycles. The mode transition point depends on the operating conditions. See Figure 14 for typical transition levels for VOUT = 2.5 V. Hysteresis exists in the transition point to prevent instability and decreased efficiencies that may result if the converter oscillates between PFM and PWM for a fixed input voltage and load current. The output voltage in PWM can be above or below the PFM voltage of that part. Soft Start The ADP1607 soft start sequence is designed for optimal control of the part. When EN goes high, or when the part recovers from a TSD, the start-up sequence begins. The output voltage increases through a sequence of stages to ensure that the internal circuitry is powered up in the correct order as the output voltage rises to its final value. Current Limit The ADP1607 is designed with a fixed 1 A typical current limit that does not vary with duty cycle. Synchronous Rectification In addition to the N-channel MOSFET switch, the ADP1607 has a P-channel MOSFET switch to build the synchronous rectifier. The synchronous rectifier improves efficiency, especially for heavy load currents, and reduces cost and board space by eliminating the need for an external Schottky diode. Compensation The PWM control loop of the ADP1607 is internally compensated to deliver maximum performance with no additional external components. The ADP1607 is designed to work with 2.2 H chip inductors and 10 F ceramic capacitors. Other values may reduce performance and/or stability. Thermal Shutdown (TSD) Protection The ADP1607 includes thermal shutdown (TSD) protection when the part is in PWM mode only. If the die temperature exceeds 150C (typical), the TSD protection activates and turns off the power devices. They remain off until the die temperature falls below 135C (typical), at which point the converter restarts. Rev. C | Page 11 of 16 ADP1607 Data Sheet APPLICATIONS INFORMATION SETTING THE OUTPUT VOLTAGE The ADP1607 can be configured for output voltages between 1.8 V and 3.3 V. The output voltage is set by a resistor voltage divider, R1, from the output voltage (VOUT) to the 1.259 V feedback input at FB and R2 from FB to GND (see Figure 24). Resistances between 100 k and 1 M are recommended. For larger R1 and R2 values, the voltage drop due to the FB pin current (IFB) on R1 becomes proportionally significant and needs to be factored in. To account for the effect of IFB for all values of R1 and R2, use the following equation to determine R1 and R2 for the desired VOUT: VOUT R1 = 1 + VFB + I FB ( R1) R2 To ensure stable and efficient performance with the ADP1607, care should be taken to select a compatible inductor with a sufficient current rating, saturation current, and low dc resistance (DCR.) The maximum rated rms current of the inductor must be greater than the maximum input current to the regulator. Likewise, the saturation current of the chosen inductor must be able to support the peak inductor current (the maximum input current plus half the inductor ripple current) of the application. The inductor ripple current (IL) in steady state continuous mode can be calculated as I L = (1) where: VFB = 1.259 V, typical VIN x D L x f SW (2) where: D is the duty cycle of the application. L is the inductor value. fSW is the switching frequency of the ADP1607. The switch duty cycle (D) is determined by the input (VIN) and output (VOUT) voltages with the following equation: IFB = 0.1 A, typical INDUCTOR SELECTION The ADP1607 is designed with a 2 MHz operating frequency enabling the use of small chip inductors ideal for use in applications with limited solution size constraints. The ADP1607 is designed for optimal performance with 2.2 H inductors, which have favorable saturation currents and lower series resistances for their given physical size. D= VOUT - VIN (3) VOUT Inductors with a low DCR minimize power loss and improve efficiency. DCR values below 100 m are recommended. Table 5. Suggested Inductors Manufacturer TDK Murata Wurth Taiyo Yuden Toko Coilcraft Part Number MLP2016S2R2M MLP2520S2R2S VLF252012MT-2R2M VLF302510MT-2R2M VLF302515MT-2R2M LQM2HPN2R2MG0 LQH32PN2R2NNC 74479787222 7440430022 BRC2012T2R2MD MDT2520-CR2R2M DEM2810C (1224AS-H-2R2M) DEM2815C (1226AS-H-2R2M) XFL3012-222 XFL4020-222 Inductance (H) 2.2 20% 2.2 20% 2.2 20% 2.2 20% 2.2 20% 2.2 20% 2.2 30% 2.2 20% 2.2 30% 2.2 20% 2.2 20% 2.2 20% 2.2 20% 2.2 20% 2.2 10% DCR (m) Typ 110 110 57 70 42 80 64 80 23 110 90 85 43 81 21 Current Rating (A) 1.20 1.20 1.67 1.23 2.71 1.30 1.85 1.50 2.50 1.00 1.35 1.10 1.40 1.9 8.0 Rev. C | Page 12 of 16 Saturation Current (A) 1.20 1.04 1.37 1.57 0.70 2.35 1.10 1.40 2.20 1.6 3.1 Size (L x W x H) (mm) 2.00 x 1.60 x 1.00 2.50 x 2.00 x 1.00 2.50 x 2.00 x 1.00 3.00 x 2.50 x 1.00 3.00 x 2.50 x 1.40 2.50 x 2.00 x 0.90 3.20 x 2.50 x 1.55 2.50 x 2.00 x 1.00 4.80 x 48.0 x 2.80 2.00 x 1.25 x 1.40 2.50 x 2.00 x 1.00 3.20 x 3.00 x 1.00 3.20 x 3.00 x 1.50 3.00 x 3.00 x 1.20 4.00 x 4.00 x 2.10 Package 0806 1008 1008 1008 1210 1008 0805 1008 1212 1515 Data Sheet ADP1607 CHOOSING THE INPUT CAPACITOR CHOOSING THE OUTPUT CAPACITOR The ADP1607 also requires a 10 F output capacitor (COUT) to maintain the output voltage and supply current to the load. The output capacitor supplies the current to the load when the Nchannel switch is turned on. Similar to CIN, a 4 V or greater, low ESR, X5R or X7R ceramic capacitor is recommended for COUT. When choosing the output capacitor, it is also important to account for the loss of capacitance due to output voltage dc bias. This may result in using a capacitor with a higher rated voltage to achieve the desired capacitance value. See Figure 25 for an example of how the capacitance of a 10 F ceramic capacitor changes with the dc bias voltage. 10 8 6 4 2 0 0 1 2 3 4 5 DC BIAS VOLTAGE (V) 6 10276-034 Different types of capacitors can be considered, but for batterypowered applications, the best choice is the multilayer ceramic capacitor, due to its small size, low equivalent series resistance (ESR), and low equivalent series inductance (ESL). X5R or X7R dielectrics are recommended. Y5V capacitors should not be used due to their variation in capacitance over temperature. Alternatively, use a high value, medium ESR capacitor in parallel with a 0.1 F low ESR capacitor. 12 CAPACITANCE (F) The ADP1607 requires a 10 F or greater input bypass capacitor (CIN) between VIN and GND to supply transient currents while maintaining a constant input voltage. The value of the input capacitor can be increased without any limit for smaller input voltage ripple and better input voltage filtering. The capacitor must have a 4 V or higher voltage rating to support the maximum input operating voltage. It is recommended that CIN be placed as close to the ADP1607 as possible. Figure 25. Typical Ceramic Capacitor Performance The value and characteristics of the output capacitor greatly affect the output voltage ripple, transient performance, and stability of the regulator. The output voltage ripple (VOUT) in continuous operation is calculated as follows: VOUT = I xt QC = OUT ON COUT COUT (4) where: QC is the charge removed from the capacitor. tON is the on time of the N-channel switch. COUT is the effective output capacitance. IOUT is the output load current. t ON = D f SW (5) and, D= VOUT - VIN VOUT (6) As shown in the duty cycle and output ripple voltage equations, the output voltage ripple increases with the load current. Rev. C | Page 13 of 16 ADP1607 Data Sheet LAYOUT GUIDELINES CIN 0402 For high efficiency, good regulation, and stability, a welldesigned printed circuit board layout is required. COUT 0402 Use the following guidelines when designing printed circuit boards (also see Figure 24 for a block diagram and Figure 2 for a pin configuration). VOUT 6 VIN 1 ADP1607 EN 2 TOP VIEW * 5 SW 4 GND FB 3 R1 0402 6.5mm 7 EPAD * R2 0402 * L 2.2H 0805 10276-035 3.0mm * Figure 26. ADP1607 Recommended Layout Showing the Smallest Footprint * * Rev. C | Page 14 of 16 Keep the low ESR input capacitor, CIN, close to VIN and GND. This minimizes noise injected into the part from board parasitic inductance. Keep the high current path from CIN through the L1 inductor to SW as short as possible. Place the feedback resistors, R1 and R2, as close to FB as possible to prevent noise pickup. Connect the ground of the feedback network directly to an AGND plane that makes a Kelvin connection to the GND pin. Avoid routing high impedance traces from feedback resistors near any node connected to SW or near the inductor to prevent radiated noise injection. Keep the low ESR output capacitor, COUT, close to VOUT and GND. This minimizes noise injected into the part from board parasitic inductance. Connect Pin 7 (EPAD) and GND to a large copper plane for proper heat dissipation. Data Sheet ADP1607 OUTLINE DIMENSIONS 1.70 1.60 1.50 2.10 2.00 SQ 1.90 0.65 BSC 6 PIN 1 INDEX AREA 0.15 REF 1.10 1.00 0.90 EXPOSED PAD 0.425 0.350 0.275 3 TOP VIEW 0.60 0.55 0.50 SEATING PLANE 0.05 MAX 0.02 NOM 0.35 0.30 0.25 0.20 MIN 1 BOTTOM VIEW PIN 1 INDICATOR (R 0.15) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 0.20 REF 02-06-2013-D 4 Figure 27. 6-Lead Lead Frame Chip Scale Package [LFCSP_UD] 2.00 mm x 2.00 mm Body, Ultra Thin, Dual Lead (CP-6-3) Dimensions shown in millimeters ORDERING GUIDE Model1 ADP1607ACPZN-R7 ADP1607ACPZN001-R7 ADP1607-EVALZ ADP1607-001-EVALZ 1 Output Voltage Adjustable Adjustable Operating Modes Auto PWM Auto PWM Temperature Range -40C to +85C -40C to +85C Package Description 6-Lead LFCSP_UD 6-Lead LFCSP_UD Evaluation Board, Automatic PFM/PWM Switching Modes Evaluation Board, PWM Mode Only Z = RoHS Compliant Part. Rev. C | Page 15 of 16 Package Option CP-6-3 CP-6-3 Branding LJ5 LJ1 ADP1607 Data Sheet NOTES (c)2012-2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10276-0-12/13(C) Rev. C | Page 16 of 16 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADP1607ACPZN001-R7 ADP1607ACPZN-R7 ADP1607-001-EVALZ ADP1607-EVALZ