AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Cable Assemblies, Series III AMPLIMITE .050 Series Connectors, Series III To meet Standard Applications the following 106 ohm, black jacketed cable assemblies are available. For AMPLIMITE .050 Series cable assemblies that meet other impedance requirements or other lengths consult TE. SCSI-2 SCSI-1 to SCSI-2 RS-232 (Alternate) to RS-232 RS-232 (Alternate) IPI-2 and HIPPI 2 Feet Part Numbers 2 Meters 3 Meters SCSI-2 50 pos. .050 Series Plug to 50 pos. .050 Series Plug 750254-1 5750254-2 750254-3 SCSI-2* 68 pos. .050 Series Plug to 68 pos. .050 Series Plug -- 5750732-2 5750732-4 RS-232 (Alternate) 26 pos. .050 Series Plug to 26 pos. .050 Series Plug -- 750255-2 750255-3 Application Assembly 5 Meters Part Numbers 15 Meters 25 Meters IPI-2 and HIPPI 100 pos. .050 Series Plug to 100 pos. .050 Series Plug 749755-2 -- -- Application Assembly *This version has spring latches. Consult TE for availability of jackscrew version. Note: .050 centerline ribbon cable assemblies are available in single or double ended versions. These assemblies are made using AMPLIMITE .050 Series panel mount connectors, AMPLIMITE .050 Series all-plastic connectors and AMP-LATCH Novo receptacles. Consult TE. SCSI--Small Computer Systems Interface HIPPI--High Performance Parallel Interface IPI--Intelligent Peripheral Interface Note: All part numbers are RoHS compliant. 6 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Right-Angle Receptacle Headers, Series III .463 [11.76] AMPLIMITE .050 Series Connectors, Series III .118.003 [3.000.08] K Materials: G E Housing -- Thermoplastic, 94V-0 rated, black. SMT compatible Shell -- Steel, plated bright nickel over copper Bracket -- Zinc, plated nickel over copper Contacts -- Phosphor bronze, duplex plated [.000030] 0.00076 min. gold on mating end; tin on solder end; all underplated nickel Position 1 F .050 Typ. [1.27] .100 [2.54] Typ. .406 [10.31] 2-56 UNC 2B Holes Last Position Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Technical Documents: Product Specifications -- 108-1228 Application Specifications -- 114-40029 Shown With Boardlocks No. of Pos. 40 50 50 68 100 E 1.580 40.13 1.830 46.48 1.830 46.48 2.280 57.91 3.080 78.23 Dimensions F G .950 24.13 1.200 30.48 1.200 30.48 1.650 41.91 2.450 62.23 1.815 46.10 2.065 52.45 2.065 52.45 2.515 63.88 3.315 84.20 K 1.415 35.94 1.665 42.29 1.665 42.29 2.115 53.72 2.915 74.04 w/ Rails and Latchblocks With .100 [2.54] Solder Tails Without With Boardlocks Boardlocks Shown With Boardlocks Part Numbers w/o Rails, w/ Latchblocks With .100 [2.54] Solder Tails Without With Boardlocks Boardlocks Shown With Boardlocks w/o Rails, w/o Latchblocks With .100 [2.54] With .120 [3.05] Solder Tails Solder Tails Without With With Boardlocks Boardlocks Boardlocks -- 1761028-2 -- 5787082-3 -- 5787170-4* -- 5787190-5 1761028-3 5787394-5 5787082-5 -- 5787170-5* 5787362-5* -- 5787266-5* -- 5787395-5* -- -- -- 5787190-7 1761028-4 5787394-7 5787082-7 5787169-7* 5787170-7* 5787362-7* -- 1761028-5 -- 5787082-9 5787169-9* 5787170-9* 5787362-9* *Has 4-40 threaded mating holes (2 places), for use with female screwlock Part No. 750644-1. Note: All part numbers are RoHS compliant. 7 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Vertical Receptacle Headers With Through-Hole Tails, Series III L P AMPLIMITE .050 Series Connectors, Series III Position 1 Position 2 Position 3 .406 [10.31] Materials: Housing--Thermoplastic, 94V-0 rated, black. SMT compatible Shell--Steel, plated bright nickel over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end; tin on solder end; all underplated nickel .350 [8.89] .100 [2.54] 2-56 Threaded Hole 2 Plc. Last Position R M Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 .125.015 [3.180.38] .351 [8.92] .150 [3.81] Note: Extra pin contact protection is provided by rails, which facilitate a straight-out, unmating motion. A side-to-side rocking motion should not be used to disengage the connector system. Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Part Number 749069-5 No. of Pos. 20 26 28 40 50 68 80 100 L 1.080 27.43 1.230 31.34 1.280 32.51 1.580 40.13 1.830 46.48 2.280 57.91 2.580 65.53 3.080 78.23 Part Number 749721-5 Dimensions M P .915 .450 23.24 11.43 1.065 .600 27.05 15.24 1.115 .650 28.32 16.51 1.415 .950 35.94 24.13 1.665 1.200 42.29 30.48 2.115 1.650 53.72 41.91 2.415 1.950 61.34 49.53 2.915 2.450 74.04 62.23 R 1.315 33.40 1.465 37.21 1.515 38.48 1.815 46.10 2.065 52.45 2.515 63.88 2.815 71.50 3.315 84.20 Part Number 749070-7 w/ Rails & Latchblocks Part Numbers w/ Latchblocks Plain 5749069-1 -- -- 5749069-2 -- -- -- 5749721-3 -- 5749069-4 -- -- 5749069-5 5749721-5 5749070-5 5749069-7 5749721-7 5749070-7 5749069-8 -- -- 5749069-9 -- 5749070-9 Note: All part numbers are RoHS compliant. 8 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Vertical Receptacle Headers With Through-Hole Tails, Series III (Continued) .120 [3.05] Solder Tail Length A D .763 [19.38] Typ. Position 1 Typ. 2-56UNC-2B 4 Holes AMPLIMITE .050 Series Connectors, Series III .050 [1.27] Typ. .008 B [0.20] C Last Position Typ. .120.007 [3.050.18] Typ. E Rails and Latch Blocks Materials: Housing--Thermoplastic, 94V-0 rated, black. SMT compatible Shell--Steel, plated bright nickel over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end; tin on solder end; all underplated nickel A D .050 [1.27] Typ. .763 [19.38] Typ. Position 1 Typ. 4-40UNC-2B 4 Holes .008 B [0.20] C Related Product Data: Required Hardware--page 26 Last Position Typ. .120.007 [3.050.18] Typ. E Technical Documents: Flat Top Configuration Product Specifications--108-1228-1 Application Specifications-- 114-40029 Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Note: Extra pin contact protection is provided by rails, which facilitate a straight-out unmating motion. A side-to-side rocking motion should not be used to disengage the connector system. No. of Pos. A 2.085 52.96 2.535 64.39 2.535 64.39 50/50 68/68 68/68 B .874 22.20 1.124 28.55 1.124 28.55 Dimensions C .500 12.70 .750 19.05 .750 19.05 D 1.830 46.48 2.280 57.91 2.280 57.91 E 1.200 30.48 1.650 41.91 1.650 41.91 Part No. 5787656-1 5787678-1 *5787679-1* *Flat-top configuration. Note: All part numbers are RoHS compliant. 9 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Vertical Receptacle Headers, Series III, with ACTION PIN Contacts (.050 x .100 [1.27 x 2.54] Centerlines) Product Facts AMPLIMITE .050 Series Connectors, Series III Recognized under the Component Program of the Underwriters Laboratories, Inc., File No. E28476 R Certified by Canadian Standards Association, File No. 1088108 (LR 7189A-207) R Produced under a Quality Management System certified to ISO 9001 A copy of the certificate is available upon request ISO900e1d i rtif Ce Shielded AMPLIMITE .050 Series headers with ACTION PIN contacts offer a high-density D type interface, and a solderless board-mount interconnection. These vertical mount headers are available in 20, 26, 50, 68 and 100 contact sizes. Choice of configurations includes; headers with rails and latch blocks, with latch blocks only, and without rails and latch blocks. ACTION PIN contact tails are available in two lengths; .173 [4.39] for pc boards with a nominal thickness of .062 [1.56] to .093 [2.36], and .280 [7.11] for pc boards with a nominal thickness of .125 [3.18] to .200 [5.08]. AMPLIMITE .050 Series headers with ACTION PIN contacts are compatible with SCSI-2, SCSI-3, EIA RS-232, IPI-2 and HIPPI standards. Principle of the AMPLIMITE .050 Series Compliant ACTION PIN Contact When an AMPLIMITE .050 Series compliant ACTION PIN contact is inserted into a platedthrough-hole, two spring members are compressed, exerting force against the hole for a gas-tight connection. The diameter of the hole is smaller than the diagonal size of the pin. AMPLIMITE .050 Series compliant ACTION PIN contact, the residual force of the elastic deformation maintains stored energy to produce a gas-tight contact zone between the pin and the plated-through-hole. This ensures long term electrical and mechanical reliability of the interconnection. Technical Documents: Product Specification-- 108-1228-2 Application Specification-- 114-40029 Instruction Sheets-- 408 6923--AMP Manual Arbor Frame Assembly 408 9027--AMP Adapter Kit for Greenerd Frame Assemblies 3A and 3B 408 9757--Seating Instructions and Tooling 408 6927--Recommendations for pc board support The beam characteristics of the pin are designed so that a plastic, as well as an elastic, deformation takes place during insertion. The two spring members compress to different degrees to accommodate hole tolerances. The compliant pin also reduces strain on the board. With a rigid pin, the elastic strain energy is stored entirely in the board, leading to damage of the platedthrough holes. With the 10 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Vertical Receptacle Headers, with ACTION PIN Tails, Series III P Position 2 Position 1 AMPLIMITE .050 Series Connectors, Series III 2-56 Thread 2 Plc. .406 [10.31] Last Position L Materials: Housings--Thermoplastic, 94V-0 rated, black, SMT compatible Shell--Carbon steel, plated bright tin over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end; tin on solder end; all underplated nickel .350 [8.89] Typ. R .275 [2.98] Typ. M Typ. Mating Face .351 [8.92] Typ. .015 S 0.38 [ ] .150 [3.81] Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Technical Documents: Product Specifications-- 108-1228-2 Application Specifications-- 114-40029 Note: Extra pin contact protection is provided by rails, which facilitate a straight-out unmating motion. A side-to-side rocking motion should not be used to disengage the connector system. Part Number 786554-1 No. of Pos. 20 26 50 68 100 120 Part Number 786554-7 L 1.080 27.43 1.230 31.34 M .915 23.24 1.065 27.05 Dimensions P .450 11.43 .600 15.24 R 1.315 33.40 1.465 37.21 1.830 46.48 1.665 42.29 1.200 30.48 2.065 52.45 2.280 57.91 2.115 53.72 1.650 41.91 2.515 63.88 3.080 78.23 3.580 90.93 2.915 74.04 3.415 86.74 2.450 62.23 2.950 74.93 3.315 84.20 3.815 96.90 S .173 4.39 .173 4.39 .173 4.39 .280 7.11 .173 4.39 .280 7.11 .173 4.39 .173 4.39 Part Number 786155-7 w/ Rails & Latchblocks Part Numbers w/ Latchblocks Plain 5786554-1 -- -- 5786554-2 -- -- 5786554-5 5786155-5 5786555-5 5786556-5 -- -- 5786554-7 5786155-7 5786555-7 786155-7 5786557-7 5786554-9 -- 5786555-9 1-5786554-0 -- -- -- Note: All part numbers are RoHS compliant. 11 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Cable Plug Connectors, Series III Shielded Plugs B AMPLIMITE .050 Series Connectors, Series III .050 [1.27] Typ. .100 [2.54] Typ. .224 [5.69] Shielded Plug .003 D [0.08] .003 Mating Face A [0.08] Typ. Shell .588.010 [14.940.25] Typ. .327 [ +.003 -.002 +0.08 8.31 -0.05 ] Housing Wire Lacing Termination Covers Termination Area Typ. Materials: Housing and Covers-- Thermoplastic, 94V-0 rated, black or gray Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, tin on termination end, all underplated .nickel Shell--Steel, plated tin-nickel alloy over nickel over min. copper Recommended wire size-- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter. Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Instruction Sheet--408-9427 Shielded Plug with Unassembled Wire Lacing Termination Covers Connector With Unassembled Wire Lacing Termination Covers No. of Pos. 26 50 68 100 A Dimensions B D .293 7.44 .293 7.44 .293 7.44 .373 9.47 .600 15.24 1.200 30.48 1.650 41.91 2.450 62.23 .979 24.87 1.579 40.11 2.029 51.54 2.829 71.86 Part Numbers .032-.036 .029-.031 [0.81-0.91] [0.74-0.79] Outer Wire Dia. Black Outer Wire Dia. Gray 5750913-2 1-5750913-2 5750913-5 1-5750913-5 5750913-7 1-5750913-7 -- 1-5750913-9 Notes: 1. Plug connector requires backshell kit for complete assembly. Refer to pages 16-19 for backshell kit part numbers. 2. For termination, cover closing and wire lacing tooling, see page 14. Note: All part numbers are RoHS compliant. 12 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Cable Plug Connectors, Series III (Continued) Shielded Plugs (Continued) .100 [2.54] Plug Shell .224 [5.69] Shielded Plug with Unassembled Standard Termination Covers AMPLIMITE .050 Series Connectors, Series III B .050 [1.27] Terminating Cover .588 [14.94] E Plug Housing D .327 [8.31] Terminating Cover Shielded Plug with Assembled Standard Termination Covers Materials: Shielded Plug with Assembled or Unassembled Standard Termination Covers Housing and Covers-- Thermoplastic, 94V-0 rated, black Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, tin on termination end, all underplated nickel Shell--Steel, plated tin-nickel alloy over nickel over copper Recommended wire size3 -- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter. Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Instruction Sheet--408-9427 Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Connectors With Standard Termination Covers No. of Pos. 20 26 28 40 50 68 80 100 120 B .450 11.43 .600 15.24 .650 16.50 .950 24.13 1.200 30.48 1.650 41.91 1.950 49.53 2.450 62.23 2.950 74.93 Dimensions D .829 21.06 .979 24.87 1.029 26.14 1.329 33.76 1.579 40.11 2.029 51.54 2.329 59.16 2.829 71.86 3.329 84.56 E .293 7.44 .293 7.44 .293 7.44 .293 7.44 .293 7.44 .293 7.44 .373 9.47 .373 9.47 .373 9.47 Part Numbers w/Rails & Latchblocks w/Latchblocks 5749111-1 5749621-1 1-5749111-0 5749621-2 -- 5749621-3 5749111-3 5749621-4 5749111-4 5749621-5 5749111-6 5749621-7 5749111-7 5749621-8 5749111-8 5749621-9 5749111-9 1-5749621-0 Notes: 1. Plug connector requires backshell kit for complete assembly and must use round jacketed cable (discrete or laminated). Refer to pages 16-19 for backshell kit part numbers. 2. For termination tooling, see pages 28 & 29. 3. The CHAMPOMATOR 2.5 Automatic Termination Machine will accept diameters as low as .023 [0.58]. Note: All part numbers are RoHS compliant. 13 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Cable Plug Connectors, Series III (Continued) AMPLIMITE .050 Series Connectors, Series III AMPLIMITE .050 Series Connector Application Tooling for Use with Wire Lacing Termination Covers Manual Arbor Frame Assembly--Part No. 58024-1 Equipped with Cover Lacing Assembly--Part No. 91293-1 (Includes Seating Bars for 50 and 100 Positions). See Table 3 for Seating Bar Part Numbers. Extra Lacing Stations available for use with Lacing Assembly--Part No. 91293-1 Order Lower Tooling Assembly--Part No. 543481-1 Arbor Frame, Part No. 58024-1 Equipped with Cover Lacing Assembly, Part No. 91293-1 Miniature Applicator Frame Assembly Part No. 91295-1 Lower Tooling Assembly Equipped with Cover Closing Kit Part No. 543508-1 Part No. 543481-1 Table Number 3 Note: AMP Manual Miniature Applicator Frame Assembly, Cover Closing Kit, and Staple Insertion Kit each must be ordered separately by part number. Seatings Bars No. of Pos. Seating Bar Part No. 26 543494-2 40 543494-3 50 543494-1 68 543502-2 100 543502-1 Note: All Tooling must be ordered separately by part number. Note: All part numbers are RoHS compliant. 14 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Cable Receptacle Connectors, Series III Shielded Receptacles .050 [1.27] Terminating Cover AMPLIMITE .050 Series Connectors, Series III .592 [15.04] Ref. B E Shielded Receptacle with Assembled Termination Covers Receptacle Housing Receptacle Shell Materials: Housing and Covers-- Thermoplastic, 94V-0 rated, black Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, tin on termination end, all underplated nickel Shell--Steel, plated bright tin over copper Recommended wire size-- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter. Terminating Cover D Mating Face Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 No. of Pos. 40 50 68 100 B .950 24.13 1.200 30.48 1.650 41.91 2.450 62.23 Dimensions D 1.329 33.76 1.579 40.11 2.029 51.54 2.829 71.86 E .293 7.44 .293 7.44 .293 7.44 .373 9.47 Part Numbers Connectors With Standard Termination Covers Assembled Covers Unassembled Covers -- -- 5749210-5 5749699-5 5749210-7 5749699-7 -- 5749699-8 Notes: 1. Receptacle connector requires backshell kit for complete assembly. Refer to pages 16-19 for backshell kit part numbers. 2. For termination, cover closing and wire lacing tooling, see page 14. 3. For Termination Tooling other than Wire Lacing see pages 28 & 29. Note: All part numbers are RoHS compliant. 15 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Shielded Backshell Kits, With Jackscrews, Series III Cable Supplied By Customer Strain Relief Staple (1 Supplied) AMPLIMITE .050 Series Connectors, Series III Jackscrew 2-56 Thd. (2 Supplied) Machine Screw A Straight Exit Male Jackscrews Style A Connector (Must Be Purchased Separately) B Upper Shield (1 Supplied) C Lower Shield (1 Supplied) Style A Straight Exit Male Jackscrews Strain Relief (1 Supplied) Cable Supplied By Customer Jackscrew 2-56 Thd. (2 Supplied) Straight Exit Male Jackscrews Style B A Machine Screws (4 Supplied) Connector (Must be Purchased Separately) B .404 [10.26] Upper Shield (1 Supplied) Straight Exit Female Jackscrews Style A C Lower Shield (1 Supplied) Style B Straight Exit Male Jackscrews Cable Supplied By Customer Materials: Jackscrews--Stainless steel or steel, black electroless nickel plated Jackscrew Caps--Polyolefin or PVC, black 2-56 Screws--Stainless steel Backshell--Zinc, plated nickel over copper Strain Relief Staple--Steel, plated tin over nickel Strain Relief Staple (1 Supplied) Jackscrew 2-56 Thd. (2 Supplied) Machine Screw A B Upper Shield (1 Supplied) Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Instruction Sheet--408-9427 Connector (Must Be Purchased Separately) C Lower Shield (1 Supplied) Style A Straight Exit Female Jackscrews 16 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Shielded Backshell Kits, With Jackscrews, Series III (Continued) No. of Pos. Style Dimensions B A C Pkg. 40 B 1.822 46.25 1.830 46.48 .456 11.58 Bulk Bulk 50 68 100 A B A 1.270 32.26 2.085 52.96 .480 12.19 1.887 47.93 1.822 46.28 2.082 52.88 1.695 43.05 2.645 67.18 2.525 64.14 3.325 84.46 3.325 84.46 .660 16.76 .564 14.33 .615 15.62 .595 15.11 Individual Bulk Bulk Individual Individual Individual .450 11.43 .400 10.16 .350 8.89 .400 10.16 .400 10.16 .550 13.97 .550 13.97 .500 12.70 .500 12.70 Male with #2-56 Threads Female with #2-56 Threads 5787543-1 1-5787543-7 5787543-2 1-5787543-8 5787543-3 1-5787543-9 5749080-1 -- 5749080-2 -- 5750752-3 -- 5786152-3 -- 5749854-1 -- 5749081-1 -- AMPLIMITE .050 Series Connectors, Series III Bulk Max. O.D. Notes: 1. Each backshell kit includes upper and lower backshells, two male or female jackscrews, one strain relief staple and two or four #2-56 screws. All are packaged unassembled. Notes: 2. For Staple Insertion Tooling see page 29. Note: All part numbers are RoHS compliant. 17 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Shielded Backshell Kits, With Spring Latches, Series III AMPLIMITE .050 Series Connectors, Series III Strain Relief Staple (1 Supplied) Cable Supplied by Customer Rear Plug Machine Screw A Spring Latch (2 Supplied) Style A Straight Exit with Latches Upper Backshell, (1 Supplied) Connector (Must be Purchased Separately) B C Lower Backshell (1 Supplied) Style A Straight Exit with Latches Style A Angled Exit with Latches Cable Supplied by Customer Strain Relief Staple (1 Supplied) Machine Screw A Spring Latch (2 Supplied) Upper Backshell (1 Supplied) Style B Straight Exit with Latches B Connector (Must be Purchased Separately) C Lower Backshell (1 Supplied) Materials: Backshell--Zinc, plated nickel over copper Spring Latch--Stainless steel 2-56 Screws--Stainless steel Strain Relief Staple--Steel, plated tin over nickel Style A Angled Exit with Latches Cable Supplied by Customer Strain Relief Staple (1 Supplied) Spring Latch (2 Supplied) A Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Instruction Sheet--408-9427 Note: Extra pin contact protection is provided by rails on the receptacle, which facilitate a straight-out unmating motion. A side-to-side rocking motion should not be used to disengage the connector system. Machine Screw B Connector (Must be Purchased Separately) Upper Backshell (1 Supplied) C Lower Backshell (1 Supplied) Style B Straight Exit with Latches 18 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Shielded Backshell Kits, With Spring Latches, Series III (Continued) Straight Exit with Latches Angled Exit with Latches Individual .270 6.86 5749190-1 5749199-1 .400 10.16 Individual .270 6.86 -- 5749609-1 .400 10.16 Individual .270 6.86 749608-2 -- .320 8.13 -- 5749201-1 .320 8.13 5749192-1 -- Individual .400 10.16 -- 5749202-2 Bulk .400 10.16 5749202-3 -- .355 9.02 5749193-1 -- .400 10.16 5749193-2 -- Bulk .480 12.19 5749889-3 -- Individual .480 12.18 5749889-4 -- .400 10.16 -- 5749204-1 .440 11.18 5749195-2 5749204-2 .420 10.67 -- 5749205-1 .500 12.70 749196-2 -- 5749197-1 5749206-1 5749198-1 5749207-1 C A 1.290 32.77 1.215 30.86 .400 10.16 A 1.290 32.77 1.365 34.67 B 1.290 32.77 1.335 33.91 20 26 A A 1.715 43.56 1.290 32.77 1.965 49.91 1.395 35.43 .400 10.16 .480 12.19 50 Individual B 68 Individual A 1.965 49.91 1.800 45.72 1.405 35.69 2.415 61.34 .492 12.50 .520 13.21 Individual A 1.600 40.64 2.715 68.96 .565 14.35 100 A 1.725 43.82 3.215 81.66 .615 15.62 Individual .500 12.70 120 A 1.725 43.82 3.715 94.36 .665 16.89 Individual .550 13.97 80 Individual AMPLIMITE .050 Series Connectors, Series III Max. O.D. Dimensions B Style 40 Pkg. A No. of Pos. Note: All part numbers are RoHS compliant. 19 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Shielded Enclosure Kits, With Male Jackscrews, Series III AMPLIMITE .050 Series Connectors, Series III 68-Position Material and Finish: Backshells--Zinc Boot--PVC, black Jackscrews--Stainless steel and PVC, black Staple--Carbon steel, plated tin over nickel Screws--Stainless steel, #2-56 threads Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 .550 [13.97] Max. Dia. Cable Supplied by Customer 1.887 [47.93] 2.645 [67.18] Connector (Must be Purchased Separately) .660 [16.76] .520 [13.21] No. of Pos. Part Number Male 2-56 Jackscrews Part Number Male 4-40 Jackscrews 68 5750752-1 5750752-2 Notes: 1. Each enclosure kit contains two backshells, one boot, two jackscrews, one staple and two screws. All are packaged unassembled. 2. For staple insertion tooling see page 29. 3. Meets SCSI-3 standards. Note: All part numbers are RoHS compliant. 20 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Panel Mount Receptacle Assemblies Without Rails, With Latch Blocks, Series III AMPLIMITE .050 Series Connectors, Series III C Recessed Cavity Identification .050 [1.27] Typ. .406 [10.31] Materials: 2-56 UNC* 2 Plc. Housing and Termination Covers-- Thermoplastic, 94V-0 rated, black Shell--Steel, plated bright nickel over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, bright tin in termination area, all nickel underplated Recommended wire size-- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter or .050 [1.27] centerline, 28 AWG [0.08-0.09mm2] stranded, PVC, flat ribbon cable. E F .004 [0.10] .201.002 [5.110.05] Mating Face .596 [15.14] Ref. Typ. .170.002 [4.320.05] D Contact Typ. Housing .007 [0.18] Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Dimensions D E Part Numbers Connectors With Unassembled Wire Lacing Termination Covers Connectors With Assembled .032-.036 .029-.031 Standard Termination Covers [0.81-0.91] [0.74-0.79] Outer Wire Dia. Outer Wire Dia. No. of Pos. C 50 1.830 46.48 1.629 41.38 2.065 52.45 1.665 42.29 1-749656-1 5-786862-5 6-786862-5 50 1.830 46.48 1.629 41.38 2.065 52.45 1.665 42.29 5-750640-1* 5-786865-5* -- 68 2.280 57.91 2.079 52.81 2.515 63.88 2.115 53.72 1-749656-2 -- -- 120 3.580 90.93 3.379 85.83 3.815 96.90 3.415 86.74 6-749656-0 -- -- F *Part Numbers 5-750640-1 and 5-786865-5 have 4-40 threaded holes. All others have 2-56 threaded holes. Note: For termination, cover closing and wire lacing tooling, see page 14. Note: For termination tooling other than wire lacing see pages 28 & 29. Note: All part numbers are RoHS compliant. 21 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Panel Mount Flat Top Receptacle Assemblies Without Rails and Latch Blocks, Series III C AMPLIMITE .050 Series Connectors, Series III .050 [1.27] Typ. Cavity Identification Terminating Cover .406 [10.31] Receptacle Housing 4-40 UNC 2 Plcs. Materials: Housing and Termination Covers-- Thermoplastic, 94V-0 rated, black Shell--Steel, plated bright nickel over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end; tin on solder end; all nickel underplated Recommended wire size-- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter or .050 [1.27] centerline, 28 AWG [0.08-0.09mm2] stranded, PVC, flat ribbon cable E .197 [5.00] Mating Face .592 Ref. [15.04] .170 .002 [4.32 0.05] Typ. D .007 [ 0.18] Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 C Dimensions D E Part Numbers Connectors With Assembled Standard Termination Covers 50 1.830 46.48 1.629 41.38 2.065 52.45 5-749877-5 68 2.280 57.91 2.079 52.81 2.515 63.88 5-749877-7 100 3.080 78.23 2.879 73.13 3.315 84.20 5-749877-9 Pos. No. of Note: For termination, cover closing and wire lacing tooling, see page 14. Note: For termination tooling other than wire lacing see pages 28 & 29. Note: All part numbers are RoHS compliant. 22 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Panel Mount Plug Assemblies With Rails, Latch Blocks, Series III Plug C AMPLIMITE .050 Series Connectors, Series III .050 Typ. [1.27] Recessed Cavity Identification .406 [10.31] 2-56 UNC 2 Plc. Materials: Housing and Termination Covers-- Thermoplastic, 94V-0 rated, black Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, bright tin in termination area, all nickel underplated Recommended wire size-- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter or .050 [1.27] centerline, 28 AWG [0.08-0.09mm2] stranded, PVC, flat ribbon cable. E F .217 .002 [5.51 0.05] .004 [ 0.10] .024 .001 Typ. [0.61 0.03] Mating Face .598 Ref. [15.19] .154 .002 [3.91 0.05] D .007 [ 0.18] Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Note: Extra pin contact protection is provided by rails, which facilitate a straight-out, unmating motion. A side-to-side rocking motion should not be used to disengage the connector system. No. of Positions 50 68 100 C 1.830 46.48 2.280 57.91 3.080 78.23 Dimensions D E 1.629 2.065 41.38 52.45 2.079 2.515 52.81 63.88 2.879 3.315 73.13 84.20 F 1.665 42.29 2.115 53.72 2.915 74.04 Part Numbers 5-749878-5 5-749878-7 5-749878-9 Note: All part numbers are RoHS compliant. 23 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Panel Mount Plug Assemblies With Rails, Latch Blocks, Series III (Continued) C AMPLIMITE .050 Series Connectors, Series III .050 [1.27] Typ. Cavity Identification .406 [10.31] 2-56 UNC* 2 Plc. Materials: Housing and Termination Covers-- Thermoplastic, 94V-0 rated, black Shell--Steel, plated bright nickel over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, bright tin in termination area, all nickel underplated Recommended wire size-- 28 AWG [0.08-0.09mm2] or 30 AWG [0.05mm2], solid or 7 strand, with a .029-.036 [0.74-0.89] insulation diameter or .050 [1.27] centerline, 28 AWG [0.08-0.09mm2] stranded, PVC, flat ribbon cable. E .004 F [0.05] .201.002 [5.110.05] Typ. Mating Face .596 [15.14] Typ. .170.002 [4.320.05] Typ. Contact Typ. Housing .007 D [0.18] Technical Documents: Product Specifications--108-1228 Application Specifications-- 114-40029 Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. Note: Extra pin contact protection is provided by rails, which facilitate a straight-out, unmating motion. A side-to-side rocking motion should not be used to disengage the connector system. No. of Pos. C D E F Part Numbers Connectors With Assembled Standard Termination Covers 20 1.080 27.43 .879 22.33 1.315 33.40 .915 23.24 5-749611-2* 26 1.230 31.24 1.029 26.14 1.465 37.21 1.065 27.05 5-749611-1* 50 1.830 46.48 1.629 41.38 2.065 52.45 1.665 42.29 5-749611-5* 50 1.830 46.48 1.629 41.38 2.065 52.45 1.665 42.29 5-750450-1* 100 3.080 78.23 2.879 73.13 3.315 84.20 2.915 74.04 5-749611-9* Dimensions *Part Number 750450-1 has 4-40 threaded holes. All others have 2-56 threaded holes. Note: For termination, cover closing and wire lacing tooling, see page 14. Note: For termination tooling other than wire lacing see pages 28 & 29. Note: All part numbers are RoHS compliant. 24 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Plug Assemblies Unshielded for .025 [0.64] Centerline Ribbon Cable, Series III .050 Typ. [1.27] Plug Assembly AMPLIMITE .050 Series Connectors, Series III E .003 [0.08] Materials: Housing and Termination Covers-- Thermoplastic, 94V-0 rated, black Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, bright tin on termination end, all over nickel underplating Recommended wire size-- .025 [0.64] centerline, 30 AWG [0.05mm2] solid or 7 strand, PVC, flat ribbon cable. Note: Cable must be approved by TE Engineering. .778.015 [19.760.38] Unshielded Plug Housing .423 [10.74] Termination Cover .025 [0.64] F .003 [0.08] No. of Pos. Technical Documents for 5786090-7 only: 50 Product Specifications--108-1359 Application Specifications-- 114-40049 68 Dimensions E F 1.578 1.578 40.07 40.07 5390377-51 2.029 51.54 5786090-7 Part No. 2.023 51.30 Note: Termination Tooling: Manual Arbor Press Part No. 91085-2 or Pneumatic Press Part No. 91112-3, Universal Base Tool Part No. 768338-4, and Connector Specific Kit Part No. 679235-2. Refer to page 29. 1 Accepts 32 AWG Flat Ribbon Cable. Selection of compatible ribbon cable is the responsibility of the user. Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts. A Backshell Kit for 5786090-7 .025 [0.64] CLC Unshielded Plug .015 B [0.38] .682.020 [17.320.51] Typ. .400.015 [10.160.38] .833 [21.16] Typ. Materials: Backshell--Thermoplastic, 94V-0 rated, black Spring Latches--Stainless steel No. of Pos. Kit Part No. 68 787032-7 .596.019 [15.140.48] .466 2 Plc. [11.84] 4 Plc. Strain Relief for 5786090-7 .025 [0.64] CC L Unshielded Plug 1.715.003 [43.560.08] 68-Position Part No. 787043-7 Materials: Thermoplastic, 94V-0 rated, black Note: Pull tab Part No. 88450-8 can be used with this strain relief. Must be ordered separately. Dimensions A B 2.415 [61.34] 2.125 [53.48] .356.002 [9.040.05] 2.109.009 [53.570.23] Note: All part numbers are RoHS compliant. 25 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Hardware and Dust Covers, Series III Screwlock Kits .187 [4.75] Materials: AMPLIMITE .050 Series Connectors, Series III Stainless steel (female) Steel, zinc plated black (male) Screwlock (2 Supplied) #2-56 Thd. Related Product Data: Used with the following connectors: Right-Angle Receptacle Header-- page 7 Vertical Receptacle Header-- pages 8-11 Panel Mount Plug and Receptacle Headers--pages 21 & 22 .062 Panel [1.57] .177 [4.50] Male Part No. 749086-1 (Includes two screwlocks) Connector .532 [13.51] .050 [1.27] Technical Documents: #4-40 Thd. Product Specifications--108-1228 Application Specifications-- 114-40029 .187 [4.75] #2-56 Thd. Screwlock .062 Panel [1.57] Female (Includes two screwlocks) Dim. A .562 14.27 .380 9.65 .562 14.27 1 Dim. B .157 3.99 .157 3.99 .165 4.19 Individual Kits Part No. Bulk Part No. 749087-1 -- 749087-21 749087-3 749087-4* 749087-8 B Connector A .050 [1.27] #4-40 Thd. Recommended for right-angle board mount connectors. .187 Dia. [4.75] 2-56 UNC B Min. Deep .027.003 [0.690.08] Typ. Female (Includes two screwlocks) Thread Size A B Kits Part No. Bulk Part No. 4-40 .110 2.79 750644-1* -- 2-56 .090 2.29 786585-2 786585-3 .100.003 [2.540.08] .355 [9.02] Recommended for pc board mount of panel mount connectors with latches or latches and rails. Permits cable connectors to be spring latchtype or jackscrew-type Note: All part numbers are RoHS compliant. A 26 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Performance Specifications and Technical Documents Performance Specifications for Right-Angle, Vertical and .050 Centerline Cable Products Mating Cycles (Durability): 500 max. Current Rating (30C T-Rise): 1A max., 50% energized AMPLIMITE .050 Series Connectors, Series III Termination Resistance (Mated): 25 milliohms max. Insulation Resistance: 1000 megohms min. Dielectric Withstanding Voltage: 500 VAC Header Processing Temperature: +220C max. for 3 minutes Temperature Range: -55C to 105C Performance Specifications for .025 [1.27] Centerline Ribbon Cable Product. Same as above except: Current Rating (30C T-Rise): 1A max. center four contacts energized (two from top row, two from bottom row) Termination Resistance (Mated): 50 milliohms max. Product Specifications: 108-1228 AMPLIMITE .050 Series Printed Circuit Board Mounted and Cable Applied 108-1359 AMPLIMITE .050 Series .025 [0.64] Centerline Connectors 108-1228 AMPLIMITE .050 Series Stacked Connectors 108-1228-2 AMPLIMITE .050 Series ACTION PIN Connectors 108-1228-3 AMPLIMITE .050 Series SBus Connectors Application Specifications: 114-40029 AMPLIMITE .050 Series Printed Circuit Board Mounted and Cable Applied Connectors 114-40049 AMPLIMITE .050 Series .025 [0.64] Centerline Connectors Instruction Sheets: 408-6923 AMP Manual Arbor Frame Assembly 408-6927 TE Design Recommendations for Printed Circuit Board Support Fixture 408-9200 AMP Single Wire Insertion Tool 408-9822 Wire Termination Tooling Kit for CHAMPOMATOR 2.5 Machine 408-9820 AMP Cover Closing and Staple Inserter Kits 408-9663 AMP Mass Insertion Tool 408-9750 AMP Cover Lacing Fixture 408-9757 AMP Tooling Assembly for ACTION PIN Receptacles 408-9817 AMP Manual Miniature Applicator Frame Assembly 408-9427 Round-to-Flat Cable Termination 408-9875 AMP Universal Base Tool for .025 [0.64] CL Connectors 408-9892 AMP Tool Kit for .025 [0.64] CL Connectors Customer Manuals: 409-5839 CHAMPOMATOR 2.5 Machine 409-5791 Control Unit for CHAMPOMATOR 2.5 Machine 27 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Application Tooling, Series III Discrete Wire Application Tooling AMPLIMITE .050 Series Connectors, Series III To meet medium to high volume production of dis-crete wire terminations, TE offers the following tooling: The CHAMPOMATOR Model 2.5 Bench Terminating Machine-- Part No. 354786-1, used in conjunction with Control Module--Part No. 852423-, and Tie Bar--Part No. 762637- (Table No. 1). Control Module Part No. 852423-1 120 VAC 852423-2 100 VAC 852423-3 230 VAC CHAMPOMATOR 2.5 Machine Tool Kit Part No. 354786-1 Note: The CHAMPOMATOR 2.5 Machine includes plug and receptacle nests, as well as wire setup gauge. Table Number 1 Connector Size Tie Bar Part No. 20 Pos. 1-762637-1 26 Pos. 1-762637-1 28 Pos. 1-762637-2 40 Pos. 1-762637-3 50 Pos. 1-762637-4 60 Pos. 1-762637-5 68 Pos. 1-762637-6 80 Pos. 1-762637-7 100 Pos. 1-762637-9 120 Pos. 1-762637-0 Discrete Wire Application Tooling For low to medium volume production use the AMP Arbor Frame Assembly-- Part No. 58024-1 equipped with Applicator--Part No. 91291-1 for .032-.035 [0.81-0.89] Conductor Insulation O.D. and Applicator--Part No. 91291-2 for .029-.032 [0.74-0.81] Conductor Insulation O.D. Note: AMP Arbor Frame Assembly and Applicator Kit must be ordered separately. Note: All part numbers are RoHS compliant. Arbor Frame Part No. 58024-1 Equipped with Applicator Part No. 91291- 28 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Application Tooling, Series III (Continued) Cover Closing/ Termination Tooling AMPLIMITE .050 Series Connectors, Series III Manual Miniature Applicator Frame Assembly-- Part No. 91295-1 This Frame requires Cover Closing Kit--Part No. 543508-1 Cable Staple Tooling To provide cable strain relief use Manual Miniature Applicator Frame Assembly-- Part No. 91295-1. This Frame requires Staple Insertion Kit--Part No. 543515-1 to install staples into lower backshells of connector kits and assemblies. AMPLIMITE .050 Series Connector Application Tooling for Use with Wire Lacing Terminating Covers Staple Insertion Kit Part No. 543515-1 (For use with Miniature Applicator Frame Assembly Part No. 91295-1) Miniature Applicator Frame Assembly Part No. 91295-1 Equipped with Cover Closing Kit Part No. 543508-1 Manual Arbor Frame Assembly--Part No. 58024-1 Equipped with Cover Lacing Assembly--Part No. 91293-1 (Includes Seating Bars for 50 and 100 Positions). See Table 3 for Seating Bar Part Numbers. Extra Lacing Stations available for use with Lacing Assembly--Part No. 91293-1 Order Lower Tooling Assembly--Part No. 543481-1 Seatings Bars Table Number 3 Seating Bar Part No. 26 543494-2 50 543494-1 68 543502-2 100 543502-1 Notes: All Tooling must be ordered separately by part number. Two seating bars required per tool assembly. Arbor Frame, Part No. 58024-1 Equipped with Cover Lacing Assembly, Part No. 91293-1 Note: AMP Manual Miniature Applicator Frame Assembly, Cover Closing Kit, and Staple Insertion Kit each must be ordered separately by part number. Lower Tooling Assembly Part No. 543481-1 No. of Pos. Termination Tooling for .025 [0.64] Centerline Ribbon Cable Used with Manual Arbor Tool Part No. 91085-2, or Pneumatic Arbor Tool Part No. 91112-3 and Universal Base Tool Part No. 768338-4. No. of Pos. 50 68 Plug/Receptacle Upper Tooling Kit 679235-2 Note: All part numbers are RoHS compliant. 29 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Slimline Connectors Product Facts AMPLIMITE .050 Series Connectors, Series III Compact design, profile for the right-angle header 1.230 x .588 [31.24 x 14.94], vertical header 1.230 x .433 [31.24 x 11.00], right-angle stacked headers 1.230 x .803 [31.24 x 20.40] Housings and covers made of UL 94V-0 rated thermoplastic Headers are compatible with surface mount reflow solder processes Header footprint for rightangle and stacked configurations is .100 x .050 [2.54 x 1.27] staggered centerlines Right-angle and stacked headers feature integral boardlocks for positive board retention and grounding Stacked headers reduce overall total header volume by 48% and PC board area by 38% Stacked headers offer optional contact shield for additional EMI/RFI protection Plugs preloaded with insulation displacement contacts (IDC) provide fast, reliable and economical terminations Aesthetically designed backshell kits feature easy-to-use finger grip jackscrews to secure mated connectors Listed and complies with UL 1863, Communication Circuit Accessories, File No. E81956 R Certified by Canadian Standards Association File No. 1088108 (LR 7189A-207) R Produced under a Quality Management System certified to ISO 9001 A copy of the ISO900e1d certificate is available tifi upon request r Ce Shielded AMPLIMITE .050 Series, Slimline Connectors answer today's industry requirement for higher density in a smaller overall package. The present line consists of 26 position, shielded right-angle, 26 position right-angle stacked PCB receptacle header, and mating 26 position plug connectors. All header, plug and backshell housings are made of UL 94V-0 rated thermoplastic. PCB headers are compatible with surface mount reflow solder processes. Right-angle and stacked PCB headers feature con-tact footprints on .100 x .050 [2.54 x 1.27] staggered centerlines. The compact design of the right-angle header package measures only 1.230 W x .588 D x .300 H [31.24 W x 14.94 D x 7.62 H] for maximum board real estate conservation. Right-angle PCB headers feature integral boardlocks for positive board retention and grounding. Right-angle stacked headers provide 52 contacts in a package only .635 [16.13] high, allowing parallel (board-over-board) board spacing of .800 [20.32]. Centerlines between the top connector and the bottom connector measure .335 [8.51] when compared to .400 [10.16] on the standard .050 Series stacked headers. This results in an over-all reduction of total header volume, in comparison to the standard AMPLIMITE .050 Series header, of 48%, and a comparative reduction in PC board area of 38%. Stacked header board retention and stabilization is provided by two boardlocks and four grounding posts. In addition, an optional rear contact shield is available for additional EMI/RFI protection. The mating plug connector consists of a thermoplastic housing, preloaded with insulation displacement contacts (IDC) for fast, reliable terminations that offer greater applied cost savings. TE offers a choice of termination equipment to meet your production requirements. The backshell hardware kit includes a two-piece, aesthetically designed, thermoplastic cover over an inner and outer shield and two, high strength #2-56 male jackscrews with insulated heads (easy finger grip caps) to secure mated connectors. The AMPLIMITE .050 Series, Slimline family of connectors offers keyed coupling. This feature eliminates the problem of mismatch mating of plug and receptacle, particularly in stacked applications. 30 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Slimline Connectors (Continued) Right-Angle Header, Receptacle .118 [3.00] AMPLIMITE .050 Series Connectors, Series III Date Code Marked In Area Indicated .975 [24.77] .588 [14.94] Position 1 Part No. 750823-1 .300 [7.26] Material and Finish .100 [2.54] 1.230 [31.24] Housing--UL 94V-0 rated thermoplastic, black Bracket--Zinc, plated tin or tin over copper Metal-Shell--Carbon steel, plated tin over copper Boardlocks--Copper alloy, tin plated Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, tin plated on solder end, all over nickel Position 26 .263 [6.680] .050 [1.27] Typ. .338 [8.59] .188 [4.76] .050 [1.27] Typ. .600 [15.24] Notes: 1. Rear panel mounting only. 2. Female screwlocks to be used with connectors mounted to panels having a thickness of .047 [1.19]. 3. See Application Specification 114-40036 for the most up-to-date detailed panel cutout and recommended PC Board hole pattern. 4. Female screwlocks are not included with receptacles and must be ordered separately. See page 33 for screwlock kit information. Note: All part numbers are RoHS compliant. 31 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Slimline Connectors (Continued) Shielded Right-Angle Stacked Header, Receptacle Shield Date Code Marked In Area Indicated AMPLIMITE .050 Series Connectors, Series III .168 [4.27] .215 [5.46] 2 Plc. .870.015 [22.100.38] .803 [20.40] Position 1 With Shielding Position 1 Position 26 .635 [16.13] 1.230 [31.24] Position 26 Without Shielding Material and Finish: .363 [9.22] .050 [1.27] Typ. Housing--UL 94V-0 rated thermoplastic, black Bracket--Zinc, plated tin over copper Metal-Shell--Carbon steel, plated tin over copper Boardlocks--Copper alloy, tin plated Contact Shield--Phosphor bronze, plated tin Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. on mating end, tin plated on solder end, all over nickel .188 [4.76] .538 [13.67] .050 Typ. [1.27] .600 [15.24] Shielded Header with Rear Contact Shield No. of Positions 26/26 Part Numbers Std. Rcpt. without Rcpt. with Rear Contact Shield Rear Contact Shield3 Keyed1 Unkeyed2 Keyed1 Unkeyed2 -- 5786200-1 5750821-1 5750820-1 Lower header unkeyed with 4-40 threaded holes, upper header keyed in keying position 1. See page 33 for keying code. Both headers unkeyed with 4-40 threaded holes. 3Receptacle includes a metal contact shield for added RFI protection to the rear of the receptacle assembly. 1 2 Note: See Application Specification 114-40036 for the most up-to-date detailed panel cutout and recommended PC Board hole pattern. Note: All part numbers are RoHS compliant. 32 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Slimline Connectors (Continued) Cable Connector, Plug AMPLIMITE .050 Series Connectors, Series III Part No. 750833-1 Material and Finish: .275 [6.99] Housing and Termination Covers-- UL 94V-0 rated thermoplastic, black Shell--Steel, plated bright tin over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end, bright tin on termination end, all underplated nickel Bracket--Zinc, plated nickel over copper Recommended Wire Size--28 AWG [0.08 mm2] with max. O.D. .032 [0.813]. PVC or polyolefin insulation. .576 [14.63] .975 [24.77] 1.170 [29.72] Note: Cable Connectors must be used with Backshell Kits. See page 34. Keying Code, Receptacle Keying Code, Plug Position 1 (Up) Accessories #2-56 Thread .170 [4.32] Female Screwlock Kit .142 [3.61] Material--Stainless Steel .170 [4.32] Note: Female screwlocks to be used with connectors mounted to panels having a thickness of .047 [1.19] .390 [9.91] #4-40 Thread Part No. 750831-1 Packaging Individually Packed Kit (2 Screwlocks per kit) *Minimum order is 510 kits. Note: All part numbers are RoHS compliant. 33 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Slimline Connectors (Continued) AMPLIMITE .050 Series Connectors, Series III Backshell Kits 1.745 [44.32] Material and Finish: Backshells--Copper-nickel alloy Jackscrews--Steel, plated tin over copper, handles covered with ABS, gray Keyed and Unkeyed Inserts--Zinc, plated tin over copper Outside Covers--ABS, gray 1.250 [31.75] .330 [8.38] Connector shown for illustration purposes only, must be purchased separately. .805 [20.45] Cable Supplied By Customer Must Be TE Approved Inner Shell 1.531 [38.89] Outer Shell 1.252 [31.80] .275 [6.98] Plug Assembly Must Be Purchased Separately Backshell Kits Unkeyed Kit Part No. 750850-1 750850-2 Cable Dia. Packaging* .250-.280 6.35-7.11 Individually Packed Kit Bulk Packed Kit 750850-3 .280-.310 7.11-7.87 Individually Packed Kit *Bulk packaging--100 kits per box. Note: All part numbers are RoHS compliant. 34 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Slimline Connectors, Application Tooling Discrete Wire Application Tooling The CHAMPOMATOR Model 2.5 Bench Terminating Machine-- Part No. 354786-1, used in conjunction with Control , Module--Part No. 852423- and Tie Bar--Part No. 1-762637-3. Note: CHAMPOMATOR 2.5 Machine and Control Module must be ordered separately by part number. Control Module Part No. 852423-1 120 VAC 852423-2 100 VAC 852423-3 230 VAC AMPLIMITE .050 Series Connectors, Series III To meet medium to high volume production of discrete wire terminations, TE offers the following tooling: CHAMPOMATOR 2.5 Machine Part No. 354786-1 26 Position Tie Bar 1-762637-3 Wire Setup Gauge Wire Insulation Dia. mm in. 0.66-0.71 .026-.028 .029-.031 0.74-0.79 .032-.035 0.81-0.89 Part No. 763382-3 763382-4 763382-5 Discrete Wire Application Tooling For low to medium volume production use the TE Arbor Tool--Part No. 58024-1 equipped with Applicator-- Part No. 91291-1 and Special Locator--Part No. 543506-1. Cable-to-Shell Staple Tooling (For discrete wire jacketed cable only) Arbor Tool Part No. 58024-1 Equipped with Applicator Part No. 91291-1 To meet medium to high volume production use TE Pneumatic Crimper-- Part No. 312522-3 equipped with Die Holder Assembly-- Part No. 58449-1 and Die-- Part No. 90437-1 to crimp outer backshells onto inner backshells of connector kits and assemblies. For low volume use Manual Arbor Tool--Part No. 91085-2, equipped with Backshell Crimper Assembly Tool-- Part No. 856684-1. For tooling information call Tooling Assistance Center 1-800-722-1111. Staple Insertion Kit Part No. 543515-1 (For use with Miniature Applicator Frame Assembly Part No. 91295-1) Backshell Tooling and Cover Tooling Miniature Applicator Frame Assembly Part No. 91295-1 Equipped with Cover Closing Kit Part No. 543508-1 Pneumatic Bench Tool No. 312522-3 (Requires Die Set Holder No. 58449-1) To assemble backshell into plastic housing use Manual Miniature Applicator Frame Assembly--Part No. 91295-1 equipped with Part No. 543521-1. To assemble upper cover on lower cover use Part No. 91295-1 equipped with Part No. 543522-1. Note: All part numbers are RoHS compliant. 35 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors Shielded AMPLIMITE .050 Series Contact Arrangements, Performance Specifications, Technical Documents--Slimline Connectors A AMPLIMITE .050 Series Connectors, Series III Contact Arrangements Position 1 C B Note: Mating face of receptacle is shown, plug is mirror image. No. of Pos. 26 A 13 Position No. B C 14 26 Performance Specifications Mating Cycles (Durability): 500 max. Current Rating (30C T-Rise): 1A max., 50% loading Termination Resistance (Mated): 25 milliohms max. Insulation Resistance: 1000 megohms min. Dielectric Withstanding Voltage: 500 VAC Header Processing Temperature: +220C max. for 3 minutes Temperature Range: -55C to +105C Technical Documents Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineer. 108-1366 Shielded AMPLIMITE .050 Series, Slimline Connectors Application Specifications describe requirements for using the product in its intended application and/or termination information. They are intended for the Packaging and Design Engineer and the Setup person. 114-40036 Shielded AMPLIMITE .050 Series, Slimline Connectors Instruction Sheets provide instructions for assembling or applying product. They are intended for Manufacturing Assembler or Operator. 408-9663 Mass Insertion Tooling-Part No. 91291- 408-6923 AMP Manual Arbor Frame-Part No. 58024-1 408-9701 Wire Termination Tooling Kit for CHAMPOMATOR 2.5 Machine-Part No. 1-762661-4 408-7777 AMP Manual Arbor Frame w/Slide-Part No. 91085-2 408-9746 Crimper Assembly-Part No. 856684-1 408-9200 Single Wire Insertion Tool-Part No. 58430-1 408-9721 Die Holder Assembly for Pneumatic Crimper- Part No. 58449- 408-9788 Die Assembly-Part No. 90437-1 408-9898 Backshell and Cover Tooling Assemblies- Part No. 543521-1 and 543522-1 Customer Manuals provide information on TE termination equipment. They are intended for Manufacturing Assemblers or Operators. 409-5786 CHAMPOMATOR 2.5 Machine 409-5791 CHAMPOMATOR 2.5 Control Module- Part No. 852423- 409-5822 Pneumatic Crimper-Part No. 312522-3 409-5843 Pneumatic Power Unit Note: All part numbers are RoHS compliant. 36 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 AMPLIMITE Subminiature D Connectors AMPLIMITE .050 Series Panel Mount Receptacle Assemblies for .025 [0.64] Centerline Ribbon Cable, Series III E .006 [0.15] .050 [1.27] Typ. AMPLIMITE .050 Series Connectors, Series III .406 [10.31] see table Materials: Housing and Termination Covers-- Thermoplastic, 94V-0 rated, black Shell--Steel, plated bright tin over copper Bracket--Zinc, plated nickel over copper Contacts--Phosphor bronze, duplex plated .000030 [0.00076] min. gold on mating end; tin on solder end; all nickel underplated Recommended wire size-- .025 [0.64] centerline, 30 AWG [0.05mm2] and 32 AWG [0.03mm2] solid or 7 strand, PVC, flat ribbon cable. Selection of compatible ribbon cable is the responsibility of the user. latch blocks .170.002 [4.320.05] Termination Cover Receptacle Housing .025 [0.64] F See customer drawings for Product Performance criteria. 50 Recognized under the Component Program of Underwriters Laboratories, Inc., File No. E28476 R Certified by Canadian Standards Association, File No. LR 7189 .004 [0.10] .423 [10.74] Technical Documents: G .201.002 [5.110.05] No. of Pos. .786.015 [19.960.38] Panel Mount Bracket H R 68 E 1.831 46.50 1.831 46.50 1.831 46.50 1.831 46.50 1.831 46.50 1.831 46.50 2.281 57.93 2.281 57.93 2.281 57.93 2.281 57.93 2.281 57.93 .003 [0.08] Dimensions F G 1.602 N/A 40.70 1.602 N/A 40.70 1.602 40.70 1.602 40.70 1.602 40.70 1.602 40.70 2.018 51.50 2.018 51.50 2.018 51.50 2.018 51.50 2.018 51.50 1.664 42.27 1.664 42.27 1.664 42.27 1.664 42.27 N/A N/A 2.114 53.70 2.114 53.70 2.114 53.70 H 2.066 52.47 2.066 52.47 2.066 52.47 2.066 52.47 2.066 52.47 2.066 52.47 2.516 63.90 2.516 63.90 2.516 63.90 2.516 63.90 2.516 63.90 Gold Plating Mating Hardware Part No. 15 w/ 4-40 threaded holes 1-5390378-5 30 w/ 4-40 threaded holes 5390378-5 30 w/ latch blocks and 4-40 threaded holes w/ latch blocks and 4-40 threaded holes w/ latch blocks and 4-40 threaded holes w/ latch blocks and 2-56 threaded holes 15 w/ 4-40 threaded holes 1-5390378-7 30 w/ 4-40 threaded holes 5390378-7 flash 15 30 flash 15 30 w/ latch blocks and 4-40 threaded holes w/ latch blocks and 4-40 threaded holes w/ latch blocks and 4-40 threaded holes 2-5390399-5 1-5390399-5 5390399-5 5390379-5 2-5390399-7 1-5390399-7 5390399-7 Note: Termination Tooling: Manual Arbor Press Part No. 91085-2 or Pneumatic Press Part No. 91112-3, Universal Base Tool Part No. 768338-4, and Connector Specific Kit Part No. 1490479-1. Note: All part numbers are RoHS compliant. 37 Catalog 82068 Revised 4-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in inches and millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015