SMC600PS12-CI - XP POWER - Datasheet.Live

ACDC

Specification

500600 Watts

•High Peak Load Rating

•Single Outputs from 3.3 V to 54 V

•Active PFC

•Remote On/Off

•Optional Current Share

•SEMI F47 Compliant

•3 Year Warranty

SMC/SMD Series

Input

Input Voltage • 90-264 VAC (120-370 VDC)

Input Frequency • 47-63 Hz

Input Current • 9 A at 90 VAC, 3.5 A at 230 VAC

Inrush Current • 40 A at 230 VAC

Power Factor • EN61000-3-2 class A

EN61000-3-2 class C for load ≥40%

Earth Leakage Current • <2.4 mA max at 264 VAC

Input Protection • Fitted with a T10 A/250 V fuse

Output

Output Voltage • See tables

Output Voltage Trim • ±5% minimum

Initial Set Accuracy • ±1%

Minimum Load • 1% load required to meet specified

ripple & noise and regulation

Start Up Delay • 1.5 s at 230 VAC, 2.5 s at 110 VAC

Start Up Rise Time • 40 ms typical

Hold Up Time • 18 ms min at 120 VAC

Line Regulation • ±0.5%, low line to high line

Load Regulation • ±1%, 1-100% of load, see note 4

Over/Undershoot • 5% max

Transient Response • 5% max deviation, 500 µs recovery to

within 1% for a 50% load change

Ripple & Noise • See table

Overvoltage Protection • 110-130% recycle input to reset

Overtemperature • >85 ˚C ambient with auto recovery

Protection (measured internally)

Overload Protection • 110% to 135% with auto recovery

Short Circuit Protection • Trip and restart (Hiccup mode)

Remote Sense • Compensates for up to 0.5 V line drop

(not available with current share)

Remote On/Off • On = TTL Logic HIGH, or open circuit

Off = TTL Logic LOW or short circuit

Current Share • Optional single wire current share, will

allow up to 4 units share within 10%,

includes ORing diode

xppower.com

General

Efficiency • 80% min at 230 VAC, 70% min for Vo ≤5V

Isolation • 3000 VAC Input to Output,

1500 VAC Input to Ground,

250 VDC Output to Ground

Switching Frequency • 100 kHz PFC, 25 kHz PWM typical

Power Density • 6.93 W/In3

Signals • Green LED for Power On, Power Good

TTL HIGH within 100-500 ms and LOW

≥1 ms before loss of regulation

Current Monitor • 0.5 V to 3 V output voltage denoting

0-100% output current

MTBF • 100 kHrs min to MIL-HDBK-217F

at 25 °C, GB

Environmental

Operating Temperature • 0 °C to +70 °C, derate from 100% load at

+50 °C to 50% load at +70 °C

Cooling • 30 CFM for SMD U-channel versions

(SMC Versions have integral fan)

Operating Humidity • 5-90%, non-condensing

Storage Temperature • -20 °C to +85 °C

Operating Altitude • 3000 m

Shock • 15 g (non-operation), 11 ms (half sine

wave), 3 times for each axis

Vibration • 10-55 Hz (non-operation) 2 g, sweep time

3 mins, 60 mins/axis

EMC & Safety

Emissions • FCC Part 15 &

CISPR 22 Class B conducted

Harmonic Currents • EN61000-3-2 class A

EN61000-3-2 class C for load ≥40%

Voltage Flicker • EN61000-3-3

ESD Immunity • EN61000-4-2, level 3 Perf Criteria A

Radiated Immunity • EN61000-4-3, 3 V/m Perf Criteria A

EFT/Burst • EN61000-4-4, level 2 Perf Criteria A

Surge • EN61000-4-5, installation class 3

Perf Criteria A

Conducted Immunity • EN61000-4-6, 3V Perf Criteria A

Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms,

100% 5000 ms Perf Criteria A, B, B

Safety Approvals • UL60950, CSA C22.2 No. 950,

EN60950, CE Mark LVD, SEMI F47

Compliant (high line only) at 100%

rated power output

ACDC

SMC/SMD Series

Models and Ratings

Output

Power

Output Voltage(3) Output Current Ripple

& Noise(2)

Model

Number

Preset Maximum Peak(1)

264 W 3.3 V 80.00 A 120.00 A 75 mV SMC500PS03-C(6)

400 W 5.0 V 80.00 A 120.00 A 75 mV SMC500PS05-C(6)

500 W

12.0 V 41.67 A 75.00 A 120 mV SMC500PS12-C

15.0 V 31.00 A 56.00 A 150 mV SMC500PS15-C(6)

18.0 V 27.78 A 50.00 A 180 mV SMC500PS18-C(6)

24.0 V 20.83 A 37.50 A 240 mV SMC500PS24-C

27.0 V 18.50 A 33.33 A 270 mV SMC500PS27-C(6)

36.0 V 13.89 A 25.00 A 360 mV SMC500PS36-C(6)

48.0 V 10.42 A 18.75 A 480 mV SMC500PS48-C

54.0 V 9.25 A 16.67 A 540 mV SMC500PS54-C(6)

297 W 3.3 V 90.00 A 135.00 A 100 mV SMC600PS03-C(6)

450 W 5.0 V 90.00 A 135.00 A 100 mV SMC600PS05-C(6)

600 W

12.0 V 50.00 A 75.00 A 120 mV SMC600PS12-C

15.0 V 40.00 A 56.00 A 150 mV SMC600PS15-C(6)

18.0 V 33.00 A 50.00 A 180 mV SMC600PS18-C(6)

24.0 V 25.00 A 37.50 A 240 mV SMC600PS24-C

27.0 V 22.22 A 33.33 A 270 mV SMC600PS27-C(6)

36.0 V 16.67 A 25.00 A 360 mV SMC600PS36-C(6)

48.0 V 12.50 A 18.75 A 480 mV SMC600PS48-C

54.0 V 11.10 A 16.67 A 540 mV SMC600PS54-C(6)

1. This peak can be taken for 500 µs only, average power should not exceed the maximum power.

2. Ripple & Noise is measured using 0.1 µF ceramic and 22 µF electrolytic capacitor, 20 MHz bandwidth.

3. Alternative output voltages available, consult sales.

4. Load regulation increases to 2% for 0-100% load change.

5. For output currents >50 A, please utilise remote sense to meet regulation ratings.

6. Available for OEM quantities, contact Sales.

Notes

Derating Curve

1. SMD units require 30 CFM forced air cooling.

Notes

010 20 30 40 50 60 70 80

Ambient Temperature (˚C)

Load (%)

100

Options

• For U-channel version replace ‘SMC’ in the part number with ‘SMD’ and remove ‘-C’ e.g. SMD600PS12 (See Derating Curve Note 1.)

• Constant current limit (95-100%) add suffix ‘-B’ (not available on 3.3 V or 5.0 V models), OEM quantities contact Sales.

• Current share and internal ORing diode add suffix ‘-I’ to model number, remote sense not available on ‘-I’ models, OEM quantities con-

tact Sales.

• Optional IEC320 inlet replace suffix ‘-C’ with ‘-D’. Not available for SMD models.

ACDC

VO-VO+

2.00

(50.8) 2.50

(63.5)

1.59

(40.4)

4.25

(108.0)

Terminal Blocks

M3.5 Screw 8 Pins 9.5 mm center

5.00 (127.0)

6.00 (152.4)

2.09

(53.0)

1.59

(40.3)

9.17 (233.0)

0.88 (22.25)

2.50

(63.6)

1.75

(44.45)

1.25 (31.9)

0.59

(15.0)

1.62

(41.25)

0.32 (8.25)

2.50 (63.5)

Terminal Block

M3 Screw

3 Pins 8.25 mm center

2.50 (63.5)

IEC320 or equivalent

‘-D’ Option

ABB A

9.17 (233.0)

2.00

(50.8)

2.50

(63.5)

2.50 (63.5)

FAN

Pin 1

Pin 7

A Mounting Hole 8 Places

0.07 (1.9)

0.02 (0.6)

0.22 (5.6)

0.25 (6.4)

UNC6-32

(Zn-plated)

B Mounting Hole 8 Places

0.07 (1.9)

0.02 (0.6)

0.22 (5.6)

0.25 (6.4)

(Zn (yellow) -plated)

CN3

Voltage

Trim

SMC/SMD Series

Mechanical Details

VO-VO+

2.00

(50.8) 2.50

(63.5)

1.00

(25.4)

4.33

(110.0)

Terminal Blocks

M3.5 Screw 8 Pins

9.5 mm center

Terminal Blocks

M3.5 Screw 8 Pins 9.5 mm center

5.00 (127.0)

6.00 (152.4)

1.50

(38.1)

1.00

(25.4)

8.00 (203.20)

0.92 (23.25)

2.50

(63.5)

1.75 (44.45)

1.29 (32.78)

N L

FAN

Pin 1

Pin 7

2.50 (63.5)

0.37

(9.5)

2.50 (63.5)

0.37

(9.5)

ABB A

2.00

(50.8)

2.50

(63.5)

Recommended

Air Flow

CN3

Voltage

Trim

All dimensions are in inches (mm)

Weight: 3.30 lbs (1.5 kg) approx.

Tolerance: ±0.012 (±0.3 mm)

SMD UChannel

1. Logic connector CN3 mates with JST XHP-7 or equivalent and JST SXH-002T-P0.6 crimp terminals.

2. Fan connector mates with JST XHP-2 or equivalent and JST SXH-002T-P0.6 crimp terminals. Output is 12 VDC/160 mA

3. Current share not available with constant current models.

4. Maximum mounting screw penetration: 0.2 (5.00) on bottom side and 0.25 (6.30) on both sides.

5. Maximum screw terminal torque: Input: 7 lbin (0.8 Nm), Output: 15.7 lbin (1.8 Nm)

Notes

CN3 (Signals)

Pin Function

1 Current monitor

2 Current share(3)

3 Return

4 Power good

5 Remote On/Off

6 -Remote sense

7 +Remote sense

SMC with integral fan

CN3 (Signals)

Pin Function

1 Current monitor

2 Current share(3)

3 Return

4 Power good

5 Remote On/Off

6 -Remote sense

7 +Remote sense

All dimensions are in inches (mm)

Weight: 3.09 lbs (1.4 kg) approx.

Tolerance: ±0.012 (±0.3 mm)

25-June-10

ACDC

Application Notes SMC/SMD Series

Remote Sense

Remote On/Off

Power Good

Parallel Connection with Current Share Option

Supply

CN3 Pin 7

CN3 Pin 6

Output

Sense

LOAD

Twisted Pair

CN3 Pin 5, control connector

ON/OFF

PSU

CN3 Pin 3, control connector

Return

CN3 Pin 4, control connector

DC OK

+5 V

1 K

CN3 Pin 3, control connector

Return POWER NOT GOOD

POWER GOOD

Supply 1 Output

Com

Return

CN3 Pin 2 Current Share

Supply 2

LOAD

Output

Return

CN3 Pin 2 Current Share

Note:

1. CL is 47 µF electrolytic capacitor.

2. CD is 0.1 µF ceramic capacitor.

Note:

1. Applying <0.3 V or short between

pins 5 and 3 turns the output OFF.

2. Applying >4.5 V or open circuit between

pins 5 and 3 turns output ON.