DAC0800,DAC0802 DAC0800/DAC0802 8-Bit Digital-to-Analog Converters Literature Number: SNAS538B DAC0800/DAC0802 8-Bit Digital-to-Analog Converters General Description Features The DAC0800 series are monolithic 8-bit high-speed current-output digital-to-analog converters (DAC) featuring typical settling times of 100 ns. When used as a multiplying DAC, monotonic performance over a 40 to 1 reference current range is possible. The DAC0800 series also features high compliance complementary current outputs to allow differential output voltages of 20 Vp-p with simple resistor loads. The reference-to-full-scale current matching of better than 1 LSB eliminates the need for full-scale trims in most applications, while the nonlinearities of better than 0.1% over temperature minimizes system error accumulations. n n n n n n n n n n n The noise immune inputs will accept a variety of logic levels. The performance and characteristics of the device are essentially unchanged over the 4.5V to 18V power supply range and power consumption at only 33 mW with 5V supplies is independent of logic input levels. Fast settling output current: 100 ns Full scale error: 1 LSB Nonlinearity over temperature: 0.1% Full scale current drift: 10 ppm/C High output compliance: -10V to +18V Complementary current outputs Interface directly with TTL, CMOS, PMOS and others 2 quadrant wide range multiplying capability Wide power supply range: 4.5V to 18V Low power consumption: 33 mW at 5V Low cost The DAC0800, DAC0802, DAC0800C and DAC0802C are a direct replacement for the DAC-08, DAC-08A, DAC-08C, and DAC-08H, respectively. For single supply operation, refer to AN-1525. Typical Application 00568601 FIGURE 1. 20 VP-P Output Digital-to-Analog Converter (Note 4) Ordering Information NonLinearity Temperature Range (TA) Order Numbers J Package (J16A) * 0.1% FS 0C to +70C DAC0802LCJ 0.19% FS -55C to +125C DAC0800LJ 0.19% FS 0C to +70C DAC0800LCJ DAC-08HQ N Package (N16E) * SO Package (M16A) DAC0802LCN DAC-08HP DAC0802LCM DAC-08Q DAC-08EQ DAC0800LCN DAC-08EP DAC0800LCM * Devices may be ordered by using either order number. (c) 2006 National Semiconductor Corporation DS005686 www.national.com DAC0800/DAC0802 8-Bit Digital-to-Analog Converters September 2006 DAC0800/DAC0802 Absolute Maximum Ratings (Note 1) Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V+ - V-) Reference Input Differential Voltage Reference Input Common-Mode +125 C DAC0800LC 0 +70 C DAC0802LC 0 +70 C (V-) + 10 (V-) + 30 V -15 -5 V - 5 mA V- to V- plus 36V Logic Inputs -55 V- V- to V+ Reference Input Current Units V+ V- to V+ Range (V14, V15) Max DAC0800L 500 mW (V14 to V15) Min Temperature (TA) 18V or 36V Power Dissipation (Note 2) (Note 1) IREF (V = -5V) 1 2 mA IREF (V- = -15V) 1 4 mA Analog Current Outputs (VS- = -15V) 4.25 mA ESD Susceptibility (Note 3) TBD V Storage Temperature -65C to +150C Lead Temp. (Soldering, 10 seconds) Dual-In-Line Package (plastic) 260C Dual-In-Line Package (ceramic) 300C Surface Mount Package Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C Electrical Characteristics The following specifications apply for VS = 15V, IREF = 2 mA and TMIN TA TMAX unless otherwise specified. Output characteristics refer to both IOUT and IOUT. Symbol Parameter Typ Max Min Typ Max Resolution 8 8 8 8 8 8 Monotonicity 8 8 8 8 8 Settling Time tPLH, tPHL Units Min 0.1 Nonlinearity ts DAC0800L/ DAC0800LC DAC0802LC Conditions Propagation Delay To 12 LSB, All Bits Switched "ON" or "OFF", TA=25C 100 DAC0800LC 100 150 ns 35 60 ns TA=25C 35 VOC Output Voltage Compliance Full Scale Current Change < 12 LSB, ROUT > 20 M, Typical IFS4 Full Scale Current VREF = 10.000V, R14 = R15 = 5.000 k, TA=25C IFS4-IFS2 IFSR Output Current Range www.national.com ns ns All Bits Switched Zero Scale Current 135 135 Full Scale Tempco Full Scale Symmetry Bits %FS 100 TCIFS IFSS 8 0.19 DAC0800L Each Bit IZS Bits 35 60 35 60 ns 10 50 10 50 ppm/C 18 V 1.99 2.04 mA -10 1.984 V- = -5V V- = -8V to -18V 0 0 2 60 18 -10 1.992 2.00 1.94 0.5 4.0 1 8.0 A 0.1 1.0 0.2 2.0 A 2.0 2.0 2.1 4.2 2.0 2.0 2.1 4.2 mA 0 0 (Continued) The following specifications apply for VS = 15V, IREF = 2 mA and TMIN TA TMAX unless otherwise specified. Output characteristics refer to both IOUT and IOUT. Symbol Parameter Min Logic Input Levels VIL Logic "0" VIH Logic "1" DAC0800L/ DAC0800LC DAC0802LC Conditions Typ Max Min Typ VLC = 0V 0.8 2.0 Logic Input Current Units Max 0.8 2.0 V V VLC = 0V IIL Logic "0" -10V VIN +0.8V -2.0 -10 -2.0 -10 A IIH Logic "1" 2V VIN +18V 0.002 10 0.002 10 A 18 V VIS Logic Input Swing V- = -15V -10 VTHR Logic Threshold Range VS = 15V -10 I15 Reference Bias Current dl/dt Reference Input Slew Rate (Figure 11) PSSIFS+ Positive Power Supply Sensitivity 4.5V V+ 18V 0.0001 0.01 0.0001 0.01 %/% PSSIFS- Negative Power Supply Sensitivity -4.5V V- 18V, IREF = 1mA 0.0001 0.01 0.0001 0.01 %/% Power Supply Current VS = 5V, IREF = 1 mA 2.3 3.8 2.3 3.8 mA -4.3 -5.8 -4.3 -5.8 mA Power Supply Current VS = +5V, -15V, IREF = 2 mA 2.4 3.8 2.4 3.8 mA -6.4 -7.8 -6.4 -7.8 mA 2.5 3.8 2.5 3.8 mA I+ I- I+ I- I+ I- PD Power Supply Current Power Consumption -1.0 4.0 18 -10 13.5 -10 -3.0 8.0 VS = 15V, IREF = 2 mA -1.0 4.0 13.5 V -3.0 A 8.0 mA/s -6.5 -7.8 -6.5 -7.8 mA 5V, IREF = 1 mA 33 48 33 48 mW +5V, -15V, IREF = 2 mA 108 136 108 136 mW 15V, IREF = 2 mA 135 174 135 174 mW Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. Note 2: The maximum junction temperature of the DAC0800 and DAC0802 is 125C. For operating at elevated temperatures, devices in the Dual-In-Line J package must be derated based on a thermal resistance of 100C/W, junction-to-ambient, 175C/W for the molded Dual-In-Line N package and 100C/W for the Small Outline M package. Note 3: Human body model, 100 pF discharged through a 1.5 k resistor. Note 4: Pin numbers represent the Dual-In-Line package. The Small Outline package pin numbers differ from from that of the Dual-In-Line package. Connection Diagrams Dual-In-Line Package Small Outline Package 00568614 Top View 00568613 Top View See Ordering Information 3 www.national.com DAC0800/DAC0802 Electrical Characteristics DAC0800/DAC0802 Block Diagram (Note 4) 00568602 Typical Performance Characteristics Full Scale Current vs. Reference Current LSB Propagation Delay vs. IFS 00568623 00568622 Reference Input Frequency Response Reference Amp Common-Mode Range 00568624 00568625 Curve 1: CC=15 pF, VIN=2 Vp-p centered at 1V. Curve 2: CC=15 pF, VIN=50 mVp-p centered at 200 mV. Note. Positive common-mode range is always (V+) - 1.5V. Curve 3: CC=0 pF, VIN=100 mVp-p centered at 0V and applied through 50 connected to pin 14.2V applied to R14. www.national.com 4 DAC0800/DAC0802 Typical Performance Characteristics (Continued) Logic Input Current vs. Input Voltage VTH -- VLC vs. Temperature 00568627 00568626 Output Current vs. Output Voltage (Output Voltage Compliance) Output Voltage Compliance vs. Temperature 00568629 00568628 Bit Transfer Characteristics Power Supply Current vs. +V 00568631 00568630 Note. B1-B8 have identical transfer characteristics. Bits are fully switched with less than 12 LSB error, at less than 100 mV from actual threshold. These switching points are guaranteed to lie between 0.8 and 2V over the operating temperature range (VLC = 0V). 5 www.national.com DAC0800/DAC0802 Typical Performance Characteristics (Continued) Power Supply Current vs. -V Power Supply Current vs. Temperature 00568632 00568633 Equivalent Circuit 00568615 FIGURE 2. Equivalent Circuit www.national.com 6 DAC0800/DAC0802 Typical Applications 00568605 IO + IO = IFS for all logic states For fixed reference, TTL operation, typical values are: VREF = 10.000V RREF = 5.000k R15 RREF CC = 0.01 F VLC = 0V (Ground) FIGURE 3. Basic Positive Reference Operation (Note 4) 00568616 00568621 FIGURE 4. Recommended Full Scale Adjustment Circuit (Note 4) Note. RREF sets IFS; R15 is for bias current cancellation FIGURE 5. Basic Negative Reference Operation (Note 4) 7 www.national.com DAC0800/DAC0802 Typical Applications (Continued) 00568617 B1 B2 B3 B4 B5 B6 B7 B8 Full Scale 1 1 1 1 1 1 1 1 IO mA IOmA EO EO 1.992 0.000 -9.960 0.000 Full Scale-LSB 1 1 1 1 1 1 1 0 1.984 0.008 -9.920 -0.040 Half Scale+LSB 1 0 0 0 0 0 0 1 1.008 0.984 -5.040 -4.920 Half Scale 1 0 0 0 0 0 0 0 1.000 0.992 -5.000 -4.960 Half Scale-LSB 0 1 1 1 1 1 1 1 0.992 1.000 -4.960 -5.000 Zero Scale+LSB 0 0 0 0 0 0 0 1 0.008 1.984 -0.040 -9.920 Zero Scale 0 0 0 0 0 0 0 0 0.000 1.992 0.000 -9.960 FIGURE 6. Basic Unipolar Negative Operation (Note 4) 00568606 B1 B2 B3 B4 B5 B6 B7 B8 EO 1 1 1 1 1 1 1 1 -9.920 +10.000 Pos. Full Scale-LSB 1 1 1 1 1 1 1 0 -9.840 +9.920 Zero Scale+LSB 1 0 0 0 0 0 0 1 -0.080 +0.160 Zero Scale 1 0 0 0 0 0 0 0 0.000 +0.080 Zero Scale-LSB 0 1 1 1 1 1 1 1 +0.080 0.000 Neg. Full Scale+LSB 0 0 0 0 0 0 0 1 +9.920 -9.840 Neg. Full Scale 0 0 0 0 0 0 0 0 +10.000 -9.920 FIGURE 7. Basic Bipolar Output Operation (Note 4) www.national.com EO Pos. Full Scale 8 DAC0800/DAC0802 Typical Applications (Continued) 00568618 If RL = RL within 0.05%, output is symmetrical about ground B1 B2 B3 B4 B5 B6 B7 B8 EO Pos. Full Scale 1 1 1 1 1 1 1 1 +9.960 Pos. Full Scale-LSB 1 1 1 1 1 1 1 0 +9.880 (+)Zero Scale 1 0 0 0 0 0 0 0 +0.040 (-)Zero Scale 0 1 1 1 1 1 1 1 -0.040 Neg. Full Scale+LSB 0 0 0 0 0 0 0 1 -9.880 Neg. Full Scale 0 0 0 0 0 0 0 0 -9.960 FIGURE 8. Symmetrical Offset Binary Operation (Note 4) 00568619 For complementary output (operation as negative logic DAC), connect inverting input of op amp to IO (pin 2), connect IO (pin 4) to ground. FIGURE 9. Positive Low Impedance Output Operation (Note 4) 00568620 For complementary output (operation as a negative logic DAC) connect non-inverting input of op am to IO (pin 2); connect IO (pin 4) to ground. FIGURE 10. Low Impedance Negative Output Operation (Note 4) 9 www.national.com DAC0800/DAC0802 Typical Applications (Continued) 00568610 Typical values: RIN=5k,+VIN=10V FIGURE 11. Pulsed Reference Operation (Note 4) 00568609 VTH = VLC + 1.4V 15V CMOS, HTL, HNIL VTH = 7.6V Note. Do not exceed negative logic input range of DAC. FIGURE 12. Interfacing with Various Logic Families www.national.com 10 DAC0800/DAC0802 Typical Applications (Continued) 00568612 (b) +VREF must be above peak positive swing of VIN 00568611 (a) IREF peak negative swing of IIN FIGURE 13. Accommodating Bipolar References (Note 4) 00568607 FIGURE 14. Settling Time Measurement (Note 4) 11 www.national.com DAC0800/DAC0802 Typical Applications (Continued) 00568608 Note. For 1 s conversion time with 8-bit resolution and 7-bit accuracy, an LM361 comparator replaces the LM319 and the reference current is doubled by reducing R1, R2 and R3 to 2.5 k and R4 to 2 M. FIGURE 15. A Complete 2 s Conversion Time, 8-Bit A/D Converter (Note 4) www.national.com 12 DAC0800/DAC0802 Physical Dimensions inches (millimeters) unless otherwise noted Molded Small Outline Package (SO) Order Numbers DAC0800LCM, or DAC0802LCM NS Package Number M16A Molded Small Outline Package (SO) Order Numbers DAC0800LCM, or DAC0802LCM NS Package Number M16A 13 www.national.com DAC0800/DAC0802 8-Bit Digital-to-Analog Converters Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Dual-In-Line Package Order Numbers DAC0800, DAC0802 NS Package Number N16E National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. Lead free products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated