3MTM MetPakTM 2-FB Header 2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series Solder Tail * End-to-end stackable * Select load capability * Monoblockable * Shoulder Pin Press Fit * End-to-end stackable * Early mate late break for hot swapping (press-fit EMLB adjusted by application tooling) * Select load capability * Monoblockable * Push-on shoulder pin * Optional feed-through tail for rear plug-up midplane applications * Accepts Universal Tooling * RoHS Compliant. See the Regulatory Information Appendix (RIA) in the "RoHS compliance" section of www.3M.com/Interconnects for compliance information (RIA E1 & C1 apply) Date Modified: September 9, 2009 TS-1120-C Sheet 1 of 4 Physical Insulation: Material: High Temp LCP Flammability: UL 94V-0 Color: Beige Color: Material: Phosphor Bronze Plating: Underplating: 50 " [1.27 m] Nickel Wiping Area: See Ordering Information Solder Tails: See Ordering Information Electrical Current Rating: Signal: 1.5 A - All contacts simultaneously Insulation Resistance: 103 M Withstanding Voltage: 1,000 VAC Environmental Temperature Rating: -55C to +125C Process Temperature Rating: 260C (Profile per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM MetPakTM 2-FB Header 2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series POSITION X 2.00 .079 "A" 6.00 .236 POSITION 2 POSITION 1 15.80 .622 11.50 .453 1.40 .055 2.00 .079 17.00 .669 FOR SPECIAL MONOBLOCKS AND PIN ARRANGEMENTS CONTACT 3M SALES REPRESENTATIVE mm [inch] 3.50 .138 Tolerance Unless Noted 12.00 .472 mm 4 ROW PRODUCT 0 0.0 0.00 3 0.3 0.13 [ ] Dimensions for Reference Only 17.80 .701 13.52 .532 MATING LENGTH "B" TAIL LENGTH 14.00 .551 E D C B A "C" ROW 5 ROW PRODUCT SOLDER TAIL PRODUCT PRESS-FIT PRODUCT PRESS-FIT PRODUCT REAR PLUG-UP Note: 1. Refer to IEC 61076-4-104 Futurebus+(R) global standard. 2. "Press Fit" describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated through-hole (PTH) in a printed circuit board, typically a "back plane." Ordering Information MP2 - HXXX - XXXX - S - XXXXX Plating Options: (See Table 4) H = Header Pin Count (See Table 1) Shouldered Pins Rows 4 = 4 Rows 5 = 5 Rows Loading Pattern (See Table 2) 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ Tail Length (See Table 3) Termination Style P = Press-Fit S = Solder Tail TS-1120-C Sheet 2 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM MetPakTM 2-FB Header 2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin Table 1 - Connector & Row Lengths Table 4 - Plating Options Pin Count Dim. "A" mm [inch] Dim "C" mm [inch] Rows 024 11.95 [0.471] 10.00 [0.394] 4 048 23.95 [0.943] 22.00 [0.866] 4 072 35.95 [1.415] 34.00 [1.339] 4 096 47.95 [1.889] 46.00 [1.811] 4 120 59.95 [2.36] 58.00 [2.283] 4 144 71.95 [2.833] 70.00 [2.756] 4 168 83.95 [3.305] 82.00 [3.228] 4 192 95.95 [3.778] 94.00 [3.701] 4 030 11.95 [0.471] 10.00 [0.394] 5 060 23.95 [0.943] 22.00 [0.866] 5 090 35.95 [1.415] 34.00 [1.339] 5 120 47.95 [1.888] 46.00 [1.811] 5 150 59.95 [2.361] 58.00 [2.283] 5 180 71.95 [2.833] 70.00 [2.756] 5 210 83.95 [3.305] 82.00 [3.228] 5 240 95.95 [3.778] 94.00 [3.701] 5 Plating Suffix Press-Fit Tails* Solder Tails TG (RIA E2 & C2 apply) (RIA E3 & C2 apply) 0.25 m [10 "] Min. Au Contact Area 2.54 m [100 "] Min. SnPb Tail Area 1.27 m [50 "] Min. Ni all over TG30 (RIA E2 & C2 apply) (RIA E3 & C2 apply) 0.76 m [30 "] Min. Au Contact Area 2.54 m [100 "] Min. SnPb Tail Area 1.27 m [50 "] Min. Ni all over TR30 (RIA E2 & C2 apply) (RIA E3 & C2 apply) 0.08 m [3 "] Min. Au Contact Area 0.67 m [27 "] Min. PdNi Contact Area 2.54 m [100 "] Min. SnPb Tail Area 1.27 m [50 "] Min. Ni all over TR40B (RIA E2 & C2 apply) (RIA E3 & C2 apply) 0.13 m [5 "] Min. Hard Au Contact Area, Lubricated 1.02 m [40 "] Min. PdNi Contact Area 0.10 m [4 "] Min. Pd Contact Area 2.54 m [100 "] Min. SnPb Tail Area 1.27 m [50 "] Min. Ni all over FJ (RIA E1 & C1 apply) (RIA E1 & C1 apply) 0.25 m [10 "] Min. Au Contact Area 5.08 m [200 "] Min. Matt Whisker Mitigating Sn Tail Area 1.27 m [50 "] Min. Ni all over KR (RIA E1 & C1 apply) (RIA E1 & C1 apply) 0.76 m [30 "] Min. Au Contact Area 5.08 m [200 "] Min. Matt Whisker Mitigating Sn Tail Area 1.27 m [50 "] Min. Ni all over RF (RIA E1 & C1 apply) (RIA E1 & C1 apply) 1.27 m [50 "] Min. Au Contact Area, Lubricated 5.08 m [200 "] Min. Matt Whisker Mitigating Sn Tail Area 1.27 m [50 "] Min. Ni all over LR (RIA E1 & C1 apply) (RIA E1 & C1 apply) 0.08 m [3 "] Min. Au Contact Area 0.67 m [27 "] Min. PdNi Contact Area 5.08 m [200 "] Min. Matt Whisker Mitigating Sn Tail Area 1.27 m [50 "] Min. Ni all over Table 3 - Tail Length Options Termination Option No. Solder Tail Press-Fit* Tail 1 2 3 1 5 (Contact 3M) 7 (Contact 3M) *Compliant-Pin Tail MP2 Series Dim. "B" 4.60 [0.181] 3.53 [0.139] 2.72 [0.107] 13.60 [0.535] 17.00 [0.669] Plating Composition PD (RIA E1 & C1 apply) (RIA E1 & C1 apply) 0.13 m [5 "] Min. Hard Au Contact Area, Lubricated 1.02 m [40 "] Min. PdNi Contact Area 0.10 m [4 "] Min. Pd Contact Area 5.08 m [200 "] Min. Matt Whisker Mitigating Sn Tail Area KV (RIA E1 & C1 apply) (RIA E1 & C1 apply) 0.76 m [30 "] Min. Au Dual Contact Areas 0.10 m [4 "] Min. Au Needle Eye 1.27 m [50 "] Min. Ni all over Table 2 - Mate Length vs. Loading Pattern Loading Pattern Code Description Mate length Row A Mate length Row B Mate length Row C Mate length Row D Mate length Row E (5-Row Prod. Only) 1 All Positions Filled 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 2 All Positions Filled 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 3 All Positions Filled 6.50 [0.256] 5.75 [0.226] 5.75 [0.226] 6.50 [0.256] 6.50 [0.256] 4 All Positions Filled 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 5 All Positions Filled 5.75 [0.226] 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 6 All Positions Filled 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 7 All Positions Filled 6.50 [0.256] 5.75 [0.226] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 8 All Positions Filled 6.50 [0.256] 5.00 [0.197] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 9 All Positions Filled 5.00 [0.197] 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] A All Positions Filled 5.00 [0.197] 5.75 [0.226] 6.50 [0.256] 5.75 [0.226] 5.00 [0.197] B All Positions Filled 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] C All Positions Filled 5.00 [0.197] 5.00 [0.197] 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] D All Positions Filled 5.75 [0.226] 5.75 [0.226] 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] E All Positions Filled 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] G All Positions Filled 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.00 [0.197] 5.00 [0.197] H All Positions Filled 5.00 [0.197] 5.75 [0.226] 5.75 [0.226] 7.25 [0.285] 7.25 [0.285] J All Positions Filled 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] K All Positions Filled 5.00 [0.197] 6.50 [0.256] 7.25 [0.285] 6.50 [0.256] 5.00 [0.197] 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ TS-1120-C Sheet 3 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM MetPakTM 2-FB Header 2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin 12.00 .472 MP2 Series 16.00 MIN .630 1 6 .0 0 M IN .6 3 0 2.00 .079 2.00 .079 A1 12.00 .472 "C" "D" PLATED THRU HO LE O 0.10 12.00 .472 2.00 .079 1.50 +.10 -.00 O CENTER HOLES OPTIONAL FOR 3M PRODUCT 6.00 .236 UNPLATED .059 +.004 -.000 "D " P L A T E D T H R U H O L E O 0 .1 0 O 0.10 RECOMMENDED 4 ROW SOLDER TAIL PCB HOLE MOUNTING PATTERN RECOMMENDED 4 ROW PRESS-FIT Table 5 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY HOLE Finished Dia. mm [in] Cu Thickness mm [in] SnPb Thickness microns ["] Drilled Hole Dia. mm [in] "D" 0.65-0.80 [.0256-.0315] 0.025 [.001] min. 15 [600] max. 0.81-0.86 [.0319-.0339] Table 6 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY Hole Finished Dia. mm [in] Cu Thickness mm [in] Immersion Matte Sn Thickness microns ["] Electrolitic Au Thickness microns ["] OSP ENTEK Thickness microns ["] Drilled Hole Dia. mm [in] "D" 0.700-0.800 [.0276-.0315] 0.025-0.045 [0.001-0.002] 0.5 - 2.5 [20 - 100] 0.1 - 0.5 [4 - 20] 0.2 - 0.5 [8 - 20] 0.830-0.860 [.0330-.0340] or 0.85mm [ #66] TWIST DRILL 18.00 MIN .709 14.00 .551 6.00 .236 2.00 .079 "D " P L A T E D T H R U H O L E O 0 .1 0 2.00 .079 A1 12.00 .472 "C" 12.00 .472 "D" PLATED THRU HOLE O 0.10 2.00 .079 O 1.50 .059 +.10 -.00 +.004 -.000 UNPLATED CENTER HOLES OPTIONAL FOR 3M PRODUCT O 0.10 RECOMMENDED 5 ROW SOLDER TAIL PCB HOLE MOUNTING PATTERN 1 8 .0 0 M IN .7 0 9 RECOMMENDED 5 ROW PRESS-FIT PCB HOLE MOUNTING PATTERN TS-1120-C Sheet 4 of 4 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. (c) 3M 2008. All rights reserved. RIA-2217B-E 3M is a trademark of 3M Company.