DS485
www.ti.com
SNLS122C JULY 1998REVISED APRIL 2013
DS485 Low Power RS-485/RS-422 Multipoint Transceiver
Check for Samples: DS485
1FEATURES DESCRIPTION
The DS485 is a low-power transceiver for RS-485
Meets TIA/EIA RS-485 Multipoint Standard and RS-422 communication. The device contains one
ensured Full Load Output Voltage (V OD3)driver and one receiver. The drivers slew rate allows
Low Quiescent Current: 200 μA typ for operation up to 2.5 Mbps (see Applications
Information section).
7V to +12V Common-Mode Input Voltage
Range The transceiver draws 200 μA of supply current when
unloaded or fully loaded with the driver disabled and
TRI-STATE Outputs on Driver and Receiver operates from a single +5V supply.
AC Performance: The driver is short-circuit current limited and is
Driver Transition Time: 25 ns typ protected against excessive power dissipation by
Driver Propagation Delay: 40 ns typ thermal shutdown circuitry that places the driver
Driver Skew: 1 ns typ outputs into TRI-STATE (High Impedance state)
under fault conditions. The driver ensures a minimum
Receiver Propagation Delay: 200 ns typ of 1.5V differential output voltage with maximum
Receiver Skew: 20 ns typ loading across the common mode range (VOD3).
Half-Duplex Flow Through Pinout The receiver has a failsafe feature that ensures a
Operates From a Single 5V Supply logic-high output if the input is open circuit.
Allows Up To 32 Transceivers on the Bus The DS485 is available in 8-pin SOIC and PDIP
Current-Limiting and Thermal Shutdown For packages and is characterized for Industrial and
Driver Overload Protection Commercial temperature range operation.
Industrial Temperature Range Operation
Pin and Functional Compatible With MAX485
and LTC485
TRUTH TABLE
Connection and Logic Diagram DRIVER SECTION
RE* DE DI A B
X H H H L
X H L L H
X L X Z Z
RECEIVER SECTION
RE* DE A-B RO
L L +0.2V H
L L ≤−0.2V L
H X X Z
L L OPEN*(1) H
(1) Non Terminated, Open Input only
Figure 1. 8-Pin SOIC or PDIP X = indeterminate
See D or P Package Z = TRI-STATE
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Copyright © 1998–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
DS485
SNLS122C JULY 1998REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS(1)(2)
Supply Voltage (VCC) +12V
Enable Input Voltage (RE*, DE) 0.5V to (VCC + 0.5V)
Driver Input Voltage (DI) 0.5V to (VCC + 0.5V)
Driver Output Voltage (A, B) 14V to +14V
Receiver Input Voltage (A, B) 14V to +14V
Receiver Output Voltage (RO) 0.5V to (VCC + 0.5V)
Maximum Package Power Dissipation @ +25°C SOIC Package 1.19W
PDIP Package 0.74W
Derate SOIC Package 9.5 mW/°C above +25°C
Derate PDIP Package 6.0 mW/°C above +25°C
Maximum Package Power Dissipation @ +70°C SOIC Package 0.76W
PDIP Package 0.47W
Storage Temperature Range 65°C to +150°C
Lead Temperature Range Soldering, 4 sec +260°C
ESD (HBM) 2 kV
(1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(2) Absolute Maximum Ratings are those values beyond which the safety of the device cannot be ensured. They are not meant to imply that
the devices should be operated at these limits. The table of ELECTRICAL CHARACTERISTICS specifies conditions of device operation.
RECOMMENDED OPERATING CONDITIONS Min Typ Max Units
Supply Voltage (VCC) +4.75 +5.0 +5.25 V
Operating Free Air Temperature (TA) DS485 0 +25 +70 °C
DS485T 40 +25 +85 °C
Bus Common Mode Voltage 7 +12 V
2Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS485
DS485
www.ti.com
SNLS122C JULY 1998REVISED APRIL 2013
ELECTRICAL CHARACTERISTICS
Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified(1)(2)
Symbol Parameter Conditions Pin Min Typ Max Units
VOD1 Differential Driver Output Voltage (No Load) A, B 5 V
VOD2 Differential Driver Output Voltage RL= 50Ω, (RS422), See Figure 2 2 2.8 V
with Load RL= 27Ω, (RS485), See Figure 2 1.5 2.3 5 V
ΔVOD Change in Magnitude of Output RL= 27Ωor 50Ω(3) 0.2 |V|
Differential Voltage
VOD3 Differential Driver Output Voltage— R1 = 54Ω, R2 = 375Ω1.5 2.0 5 V
Full Load with Max VCM VTEST =7V to +12V, See Figure 6
VOC Driver Common-Mode Output Voltage RL= 27Ωor 50Ω, See Figure 2 3 V
ΔVOC Change in Magnitude of Common-Mode RL= 27Ωor 50Ω, See Figure 2(3) 0.2 |V|
Output Voltage
VIH Input High Voltage DI, 2.0 V
DE,
VIL Input Low Voltage 0.8 V
RE*
IIN1 Input Current VIN = 0V or VCC ±2 μA
IIN2 Input Current(4) VIN = +12V A, B 1.0 mA
DE = 0V, VCC = 0V or 5.25V VIN =7V 0.8 mA
VTH Receiver Differential Threshold Voltage 7V VCM +12V 0.2 0.2 V
ΔVTH Receiver Input Hysteresis VCM = 0V 70 mV
VOH Receiver Output High Voltage IO=4 mA, VID = 0.2V RO 3.5 V
VOL Receiver Output Low Voltage IO= 4 mA, VID =0.2V 0.4 V
IOZR TRI-STATE Output Current at Receiver 0.4V VO2.4V ±1 μA
RIN Receiver Input Resistance 7V VIN +12V A, B 12 kΩ
ICC No-Load Supply Current(5) DE = VCC, RE* = 0V or VCC VCC 200 900 μA
DE = 0V, RE* = 0V or VCC 200 500 μA
IOSD1 Driver Short Circuit Current, VO= HIGH 7V VO+12V A, B 35 250 mA
IOSD2 Driver Short Circuit Current, VO= LOW 7V VO+12V 35 250 mA
IOSR Receiver Short Circuit Current 0V VOVCC RO 7 85 mA
(1) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground
except VOD1/2/3 and VID.
(2) All typicals are given for: VCC = +5.0V, TA= +25°C.
(3) Δ|VOD| and Δ|VOC| are changes in magnitude of V OD and VOC respectively, that occur when the input changes state.
(4) IIN2 includes the receiver input current and driver TRI-STATE leakage current.
(5) Supply current specification is valid for loaded transmitters when DE = 0V or enabled (DE = H) with no load.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS485
DS485
SNLS122C JULY 1998REVISED APRIL 2013
www.ti.com
SWITCHING CHARACTERISTICS
Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified(1)(2)(3)
Symbol Parameter Conditions Min Typ Max Units
tPLHD Driver Differential Propagation Delay—Low to High RL= 54Ω, CL= 100 pF 10 40 65 ns
tPHLD Driver Differential Propagation Delay—High to Low 10 39 65 ns
tSKEW Differential Skew |tPHLD tPLHD| 1 10 ns
trDriver Rise Time 3 25 40 ns
tfDriver Fall Time 3 25 40 ns
tZH Driver Enable to Output High CL= 100 pF 170 ns
tZL Driver Enable to Output Low CL= 100 pF 170 ns
tLZ Driver Disable from Output Low CL= 15 pF 170 ns
tHZ Driver Disable from Output High CL= 15 pF 170 ns
tPLHD Receiver Differential Propagation Delay—Low to High CL= 15 pF (RO) 70 190 320 ns
tPHLD Receiver Differential Propagation Delay—High to Low 70 210 320 ns
tSKEW Differential Skew |tPHLD tPLHD| 20 50 ns
tZH Receiver Enable to Output High CL= 15 pF 110 ns
tZL Receiver Enable to Output Low 110 ns
tLZ Receiver Disable from Output Low 110 ns
tHZ Receiver Disable from Output High 110 ns
fmax Maximum Data Rate See (4) 2.5 Mbps
(1) All typicals are given for: VCC = +5.0V, TA= +25°C.
(2) f = 1 MHz, trand tf6 ns, ZO= 50Ω.
(3) CLincludes jig and probe capacitance.
(4) fmax is the ensured data rate for 50 ft of twisted pair cable. f max may be conservatively determined from the ratio of driver transition time
(tr) to the data rate unit interval (1/fmax). Using a 10% ratio yields fmax = (0.1)/40 ns = 2.5 Mb/s. Higher data rates may be supported by
allowing larger ratios.
4Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS485
DS485
www.ti.com
SNLS122C JULY 1998REVISED APRIL 2013
PARAMETER MEASUREMENT INFORMATION
Figure 2. VOD Figure 3.
Figure 4. Figure 5.
Figure 6. VOD3
Figure 7.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: DS485
DS485
SNLS122C JULY 1998REVISED APRIL 2013
www.ti.com
Figure 8. Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
6Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS485
DS485
www.ti.com
SNLS122C JULY 1998REVISED APRIL 2013
Figure 14.
PIN DESCRIPTIONS
Pin # I/O Name Function
1 O RO Receiver Output: If A > B by 200 mV, RO will be high; If A < B by 200 mV, RO will be low. RO will be high also if
the inputs (A and B) are open (non-terminated).
2 I RE* Receiver Output Enable: RO is enabled when RE* is low; RO is in TRI-STATE when RE* is high.
3 I DE Driver Output Enable: The driver outputs (A and B) are enabled when DE is high; they are in TRI-STATE when DE
is low. Pins A and B also function as the receiver input pins (see below).
4 I DI Driver Input: A low on DI forces A low and B high while a high on DI forces A high and B low when the driver is
enabled.
5 NA GND Ground
6 I/O A Non-inverting Driver Output and Receiver Input pin. Driver output levels conform to RS-485 signaling levels.
7 I/O B Inverting Driver Output and Receiver Input pin. Driver output levels conform to RS-485 signaling levels.
8 NA VCC Power Supply: 4.75V VCC 5.25V
Related TI Low Power RS-485 Transceivers
Part Number Temperature Range Number of XCVRs on Bus Comments
DS36C278 0°C to +70°C 128 Ultra Low Power Transceiver
DS36C278T 40°C to +85°C 64 Ultra Low Power Transceiver
DS36C279 0°C to +70°C 128 Auto-Sleep Mode
DS36C279T 40°C to +85°C 64 Auto-Sleep Mode
DS36C280 0°C to +70°C 128 Adjustable Slew Rate Control
DS36C280T 40°C to +85°C 64 Adjustable Slew Rate Control
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: DS485
DS485
SNLS122C JULY 1998REVISED APRIL 2013
www.ti.com
APPLICATIONS INFORMATION
The DS485 is a low power transceiver designed for use in RS-485 multipoint applications. The DS485 can
transmit data up to 2.5 Mbps based on a ratio of driver transition time to the unit interval (bit time) of 10%. This
maximum data rate may be further limited by the interconnecting media. The DS485 provides a standard unit
load to the RS-485 bus across the common mode range of 7V to +12V. This allows up to 32 transceivers
(standard unit load) to be connected to the bus. More transceivers may be connected to the bus if they support a
reduced unit load (see Related TI Low Power RS-485 Transceivers). The DS485 also ensures the driver's output
differential voltage into a worst case load that models standard termination loads and 32 unit loads referenced to
the maximum common mode voltage extremes. With a minimum of 1.5V swing into this load, a 1.3V differential
noise margin is supported along with the standard common mode rejection range of the receivers.
Due to the multipoint nature of the bus, contention between drivers may occur. This will not cause damage to the
drivers since they feature short-circuit protection and also thermal shutdown protection. Thermal shutdown
senses die temperature and puts the driver outputs into TRI-STATE if a fault condition occurs that causes
excessive power dissipation which can elevate the junction temperature to +150°C.
A typical multipoint application is shown in the following figure. Note that termination is typically required but is
only located at the two ends of the cable (not on every node). Commonly pull up and pull down resistors may be
required at one end of the bus to provide a failsafe bias. These resistors provide a bias to the line when all
drivers are in TRI-STATE. See Application Note AN-847(SNLA031) for a complete discussion of failsafe biasing
of differention buses.
Figure 15. Multipoint RS-485 Application
8Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS485
DS485
www.ti.com
SNLS122C JULY 1998REVISED APRIL 2013
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C Page
Changed layout of National Data Sheet to TI format ............................................................................................................ 8
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: DS485
PACKAGE OPTION ADDENDUM
www.ti.com 25-Aug-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
DS485M LIFEBUY SOIC D 8 95 TBD Call TI Call TI 0 to 70 DS485
M
DS485M/NOPB LIFEBUY SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS485
M
DS485MX/NOPB LIFEBUY SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS485
M
DS485N/NOPB LIFEBUY PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 70 DS485
N
DS485TM LIFEBUY SOIC D 8 95 TBD Call TI Call TI -40 to 85 DS485
TM
DS485TM/NOPB LIFEBUY SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 DS485
TM
DS485TMX/NOPB LIFEBUY SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 DS485
TM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
PACKAGE OPTION ADDENDUM
www.ti.com 25-Aug-2017
Addendum-Page 2
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
DS485M DS485M/NOPB DS485MX DS485MX/NOPB DS485N/NOPB DS485TM DS485TM/NOPB DS485TMX
DS485TMX/NOPB