TTSI004321BL-2-DB - Agere Systems, Inc.

Data Sheet, Revision 3

September 21, 2005

TSI-4

4k x 4k Time-Slot Interchanger

1 Introduction

The last issue of this data sheet was August 31, 2005. A change history is included in Section 11 Change History on page

61. Red change bars have been installed on all text, figures, and tables th at were added or changed. All chang es to the text

are highlighted in red. Changes within figures, and the figure title itself, are highlighted in red, if feasible. Formatting or

grammatical changes have not been highlighted. Deleted sections, paragraphs, figures, or tables will be specifically

mentioned.

This document consists of two major sections:

The TSI-4 device hardware description. This section contains ball information, operating conditions, dc electrical charac-

teristics, timing diagrams, ac characteristics, and packaging information.

The TSI-4 device register description. This section contains register information.

1.1 Related Documents

The documenta tion package for this device consists of the following documents:

The TSI-4 4k x 4k Time-Slot Interchanger Product Brief, the TSI Family Selection Guide, the TSI-4 4k x 4k Time-Slot

Interchanger Data Sheet (this document), and the TSI-4 Time-Slot Interchanger System Design Gu ide.

These documents are available on the public website shown below.

If the reader displays thi s document using Acrobat Reader ®, clicking on any blue text will bring the reader to that reference

point.

To access related docum ents, including the do cuments mentio ned above, please go to the following public website, or con-

tact your Agere representative (see the last page of this document).

http://www.agere.com/telecom/time_slot_interchangers.html

1.2 Block Diagram and High-Level Interface Definition

Figure 1-1. Block Diagram and High-Level Interface Definition

TEST ACCESS

PORT

READ ADDRESS

COUNTER

CONNECTION

STORE

WRITE ADDRESS

COUNTER

DATA

STORE

MICROPROCESSOR

INTERFACE

TRANSMIT

CHI

TEST PA T TERN

GENERATOR

TEST PATTERN

MONITOR

CLOCK

GENERATOR

RECEIVE

CHI

32 32

4k x 4k Switch Fabric

TSI-4 Data Sheet, Revision 3
4k x 4k Time-Slot Interchanger September 21, 2005
Table of Contents
Contents Page
Agere Systems Inc.
Introduction ............... .... ... ................... .................... ................... ................... ......................................................................1
1 Related Documents ............... ... ... ... .... ................... ... ... .................... ... ................... .... ..................................................1
2 Block Diagram and High-Level Interface Definition .....................................................................................................1
Ball Information ...... ... .... ................................... ................... .................... ................... .........................................................7
1 Top View Ball Diagram ................................................................................................................................................7
2 Package Ball Assignments ..........................................................................................................................................8
3 Package Ball Matrix ...................................................................................................................................................10
3.1 Top View ......... ... ... ... .... ................ ... ... .... ... ... ... ... .... ..........................................................................................10
3.2 Bottom View  ............. .... ... ... ... .... ................................ ... ... .... ... ... ... ................ .... ... ... ..........................................11
4 Ball Types ....... ... .... ... ... ... ... ................. ... ... ... .... ... ... ................................ .... ... ... ... ... ....................................................12
5 Ball Definitions ....... ... ... ... ... .... ... .................................................................................................................................12
Operating Conditions and Reliability  ............... ... .... ... ... ... ... .... ... ... ... .... ... ... ... .................... ... ... ..........................................15
1 Absolute Maximum Ratings .......................................................................................................................................15
2 Recommended Operating Conditions  .......................................................................................................................15
3 Handling Precautions  .................. ... .... ... ... ... .... ................... ... .................... ... .............................................................15
4 Thermal Parameters (Definitions and Values) ...........................................................................................................16
5 Power Consumption  ....................... .... ... ... ................... .................... ................... .......................................................17
dc Electrical Characteristics  .............................................................................................................................................18
Timing Diagrams and ac Characteristics ..........................................................................................................................19
Register Description ........... ... ... .... ... ... ... .... .......................................................................................................................31
1 Device Addressing Notes  ................... ... ....................................................................................................................31
2 Acronyms Used  ..................... ... ... ... .... ... ... ... .... ................ ... ... ... .... ... ... ... .... ................................................................31
3 Address Map  .................. ... .... ... ................... .................... ................................... .......................................................31
4 Register Summary ....................................... .................... ................... ................... ....................................................32
5 Global Control Registers  ............. ... .... ... ... ................... .................... ..........................................................................34
6 Connection Store Generator Registers  ................. ................... .... ... ... ... .... ... ... ... ... .................... ................................39
7 Test Pattern Generator and Monitor Registers ..........................................................................................................44
8 Concentration Highway Configuration Registers .......................................................................................................48
Switch Fabric Control  ............ ... .... ... ................................... .................... ................... .......................................................54
Connection Store ................ ... ... .................... ................... .................................... .............................................................58
Outline Diagrams ..............................................................................................................................................................60
Ordering Information .......................................................................................................................................................61
Change History ...............................................................................................................................................................61
1 Navigating Through an Adobe Acrobat Document ..................................................................................................61

Data Sheet, Revision 3 TSI-4
September 21, 2005 4k x 4k Time-Slot Interchanger
Table of Contents (continued)
Contents Page
Agere Systems Inc .  3
Table 2-1. Package Ball Assignments in Signal Name Order.................................................................................................8
Table 2-2. Package Ball Assignments (Top View) ................................................................................................................10
Table 2-3. Package Ball Assignments (Bottom View)...........................................................................................................11
Table 2-4. Ball Types.... .... ... ................... ... .................... ... ................... .... ... ................... ... ....................................................12
Table 2-5. Timing Port ..........................................................................................................................................................12
Table 2-6. Transmit and Receive Concentration Highways..................................................................................................12
Table 2-7. Control Port...... ... ... ... .................... ... ................... ... .................... ... ... ....................................................................13
Table 2-8. Initialization and Test Access...............................................................................................................................13
Table 2-9. Power Balls..........................................................................................................................................................14
Table 3-1. Absolute Maximum Ratings.................................................................................................................................15
Table 3-2. Operating Conditions...........................................................................................................................................15
Table 3-3. ESD Tolerance.....................................................................................................................................................15
Table 3-4. Thermal Parameter Values.............. ... ... .... ... ... ... ... .... ... ... ... .... ... ... ... .... ................... ... ... .......................................16
Table 3-5. Power Consumption ............................................................................................................................................17
Table 4-1. CMOS Inputs............ ... .... ... ... ... .... ... ................... ... .................... ... ... .................... ................................................18
Table 4-2. CMOS Outputs ......... ... .................... ... ................... .... ... ................... .... ................... .............................................18
Table 4-3. CMOS Bidirectionals (DATA[15:0])..... .................................................................................................................18
Table 5-1. CHICLK Timing Specifications............... .... ... ... ... ... .... ... ... ... .... ... ... ... .... ... ... ... ... ....................................................19
Table 5-2. MPUCLK Timing Specifications...........................................................................................................................19
Table 5-3. CMOS Output ac Timing Specification *..............................................................................................................20
Table 5-4. CHI Interface Timing........... ... ... .... ... ... ... .... ................... ... ... .................... ... ... ... ....................................................21
Table 5-5. CHI 3-State Output Control.............. ... ................... .... ... ... ... .... ... ... ... .... ................... ... ..........................................27
Table 5-6. Microprocessor Port Timing—Read Cycle...........................................................................................................28
Table 5-7. Microprocessor Port Timing—Write Cycle...........................................................................................................29
Table 6-1. Address Map........................................................................................................................................................31
Table 6-2. Global Registers..................................................................................................................................................32
Table 6-3. Connection St ore Generator Registers................................................................................................................32
Table 6-4. Test Pattern Generator and Monitor Registers ....................................................................................................33
Table 6-5. Concentration Highway Configuration Registers.................................................................................................33
Table 6-6. Switch Fabric Control...........................................................................................................................................33
Table 6-7. Connection Store.................................................................................................................................................34
Table 6-8. Reserved Registers..... .... ... ... ... .... ... ... ... .... ................... ... .................... ... ... ..........................................................34
Table 6-9. Version_Control (Read Only)...............................................................................................................................34
Table 6-10. Chip_Identity (Read Only) .................................................................................................................................34
Table 6-11. Summary_Interrupt_Status (Read Only)............................................................................................................35
Table 6-12. Summary_Interrupt_Mask (Read/Write)............................................................................................................35
Table 6-13. CPU_Access_Error (CORWN)..........................................................................................................................36
Table 6-14. CPU_Access_Error_Mask (Read/Write)............................................................................................................36
Table 6-15. Global_Control (Read/Write) .............................................................................................................................37
Table 6-16. PLL_Control (Read/Write) .................................................................................................................................38
Table 6-17. Power_Control (Read/Write)..............................................................................................................................38
Table 6-18. Invalid_Address_Trap (Read Only)....................................................................................................................38
Table 6-19. Scratch_Register (Read/Write)..........................................................................................................................38
Table 6-20. Reserved_0 (Read/Write)..................................................................................................................................39
Table 6-21. CSG_Control (Read/Write)................................................................................................................................39
Table 6-22. CSG_Status (Read Only)...................................................................................................................................40
Table 6-23. CSG_Starting_Address (Read/Write) ................................................................................................................40
Table 6-24. CSG_Ending_Address (Read/Write) .................................................................................................................40
Table 6-25. CSG_Write_Enable_Low (Read/Write)..............................................................................................................40
Table 6-26. CSG_Write_Enable_High (Read/Write).............................................................................................................40
Table 6-27. CSG_Seed_Low (Read/Write)...........................................................................................................................41
Table 6-28. CSG_Seed_High (Read/Write)..........................................................................................................................41

TSI-4 Data Sheet, Revision 3
4k x 4k Time-Slot Interchanger September 21, 2005
Table of Contents (continued)
Tables Page
44  Agere Systems Inc.
Table 6-29. CSG_OR_Mask_Low (Read/Write)...................................................................................................................41
Table 6-30. CSG_OR_Mask_High (Read/Write)..................................................................................................................41
Table 6-31. CSG_AND_Mask_Low (Read/Write).................................................................................................................42
Table 6-32. CSG_AND_Mask_High (Read/Write)................................................................................................................42
Table 6-33. CS_Stream_Control (Read/Write) .....................................................................................................................42
Table 6-34. CSG_Configuration (Read/Write)......................................................................................................................43
Table 6-35. TPG_Configuration (Read/Write).......................................................................................................................44
Table 6-36. TPG_User_Pattern (Read/Write).......................................................................................................................44
Table 6-37. TPM_Configuration (Read/Write) ......................................................................................................................45
Table 6-38. TPM_User_Pattern (Read/Write).......................................................................................................................45
Table 6-39. TPM_Error_Count (Sat/Roll*)............................................................................................................................46
Table 6-40. TPG_Inject_Error_Count (Write Only)...............................................................................................................46
Table 6-41. TPG_Data_Invert_Mask (Read/Write)...............................................................................................................46
Table 6-42. TPM_Status (Read Only)...................................................................................................................................47
Table 6-43. TPM_Status_Mask (Read/Write) .......................................................................................................................47
Table 6-44. Receive_CHI_Configuration (Read/Write).........................................................................................................48
Table 6-45. Receive_CHI_St atus (CORWN) Receive_CHI_Status (CORWN).....................................................................48
Table 6-46. Receive_CHI_Status_Mask (Read/Write)..........................................................................................................49
Table 6-47. Receive_CHI_Global_Configuration (Read/Write) ............................................................................................49
Table 6-48. Transmit_CHI_Configuration (Read/Write)........................................................................................................50
Table 6-49. Transmit_CHI_Status (CORWN) .......................................................................................................................51
Table 6-50. Transmit_CHI_S tatus_Mask (Read/Write).........................................................................................................51
Table 6-51. Transmit_CHI_Global_Configuration (Read/Write)............................................................................................52
Table 6-52. Receive_CHI_Time_Slot_Offset (Read/Write)...................................................................................................53
Table 6-53. Transmit_CHI_Time_Slot_Offset (Read/Write)..................................................................................................53
Table 7-1. SF_Status (CORWN)...........................................................................................................................................54
Table 7-2. SF_Status_Mask (Read/Write)............................................................................................................................54
Table 7-3. Data_Store_Time_Slot_Capture_Select (Read/Write).........................................................................................55
Table 7-4. Data_Store_Captured_Data (Read Only)............................................................................................................55
Table 7-5. Connection_Store_Parity_Error_Address_Trap (CORWN).................................................................................56
Table 7-6. Receive_Link_Offset (Read Only)............................. ... ... ... .... ... ... ... .... ... ... ... ... .... ... ... ... .... ...................................56
Table 7-7. Transmit_Link_Offset (Read/Write) . ... ... ..............................................................................................................56
Table 7-8. Wide_Mode_Control (Read/Write).......................................................................................................................57
Table 8-1. Low_Control_Word (Read/Write).........................................................................................................................58
Table 8-2. High_Control_Word (Read/Write)........................................................................................................................59
Table 10-1. Ordering Information..........................................................................................................................................61

Data Sheet, Revision 3 TSI-4
September 21, 2005 4k x 4k Time-Slot Interchanger
Table of Contents (continued)
Figures Page
Agere Systems Inc .  5
Figure 1-1. Block Diagram and High-Level Interface Definition..............................................................................................1
Figure 2-1. Package Diagram (Top View) ..............................................................................................................................7
Figure 5-1. CHICLK Timing Specifications....... ... ... .... ... ... ... ... .... ... ... ... .... ... ... ... .... ................... ... ... .......................................19
Figure 5-2. MPUCLK Timing Specifications.........................................................................................................................19
Figure 5-3. ac Timing Specification............... .......................................................................................................................20
Figure 5-4. CHI Interface Timing.. .... ... ... ... ...........................................................................................................................21
Figure 5-5. Typical Receive CHI Timing with 16.384 Mbits/s Data and 16.384 MHz CHICLK.............................................22
Figure 5-6. Transmit CHI Timing with 16.384 Mbits/s Data and 16.384 MHz CHICLK ........................................................22
Figure 5-7. Typical Receive CHI Timing with 8.192 Mbits/s Data and 16.384 MHz CHICLK...............................................23
Figure 5-8. Transmit CHI Timing with 8.192 Mbits/s Data and 16.384 MHz CHICLK ..........................................................23
Figure 5-9. Typical Receive CHI Timing with 4.096 Mbits/s Data and 16.384 MHz CHICLK...............................................24
Figure 5-10. Transmit CHI Timing with 4.096 Mbits/s Data and 16.384 MHz CHICLK ........................................................24
Figure 5-11. Typical Receive CHI Timing with 2.048 Mbits/s Data and 16.384 MHz CHICLK.............................................25
Figure 5-12. Transmit CHI Timing with 2.048 Mbits/s Data and 16.384 MHz CHICLK ........................................................25
Figure 5-13. Typical Receive CHI Timing with 8.192 Mbits/s Data and 8.192 MHz CHICLK...............................................26
Figure 5-14. Transmit CHI Timing with 8.192 Mbits/s Data and 8.192 MHz CHICLK ..........................................................26
Figure 5-15. CHI 3-State Output Control..............................................................................................................................27
Figure 5-16. Microprocessor Port Timing—Read Cycle.......................................................................................................28
Figure 5-17. Microprocessor Port Timing—Write Cycle.......................................................................................................29
Figure 6-1. Transmit CHI Configuration (R/W).... .................................................................................................................50

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

66 Agere Systems Inc.

Hardware Description

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 7

2 Ball Information

2.1 Top View Ball Diagram

The device is housed in a 24 0-ball plastic ball gr id array. F igur e 2-1 sh ows th e ball arr angeme nt viewed from the top of the

package. The balls are spaced on a 1.0 mm pitch.

Figure 2-1. Package Diagram (Top View)

710

913

12 16

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

88 Agere Systems Inc.

2.2 Package Ball Assignments

Table 2-1. Package Ball Assignments in Signal Name Order

Symbol Ball Symbol Ball Symbol Ball Symbol Ball Symbol Ball

ADDR00 A17 DATA13 P18 RXD11 V7 TXD08 F1 VDD15 D13

ADDR01 A16 DATA14 P17 RXD12 T8 TXD09 G3 VDD15 D14

ADDR02 A15 DATA15 P16 RXD13 U8 TXD10 G2 VDD15 G4

ADDR03 A14 DT H17 RXD14 V8 TXD11 G1 VDD15 H4

ADDR04 A13 FSYNC T11 RXD15 U9 TXD12 H2 VDD15 L4

ADDR05 A12 HIZ R17 RXD16 V9 TXD13 H1 VDD15 M4

ADDR06 A11 INT H16 RXD17 V10 TXD14 J2 VDD15 R7

ADDR07 A10 MPUCLK K15 RXD18 U10 TXD15 J1 VDD15 R8

ADDR08 A9 PAR0 R18 RXD19 V11 TXD16 K1 VDD15 R11

ADDR09 A8 PAR1 P15 RXD20 U11 TXD17 K2 VDD15 R12

ADDR10 A7 R/W J17 RXD21 V12 TXD18 L1 VDD33 C9

ADDR11 A6 RESET H15 RXD22 U12 TXD19 L2 VDD33 C10

ADDR12 A5 RSV1 F17 RXD23 V13 TXD20 M1 VDD33 C17

ADDR13 A4 RSV2 F18 RXD24 U13 TXD21 M2 VDD33 D9

ADDR14 A3 RSV3 E15 RXD25 V14 TXD22 N1 VDD33 D10

ADDR15 A2 RSV4 E16 RXD26 U14 TXD23 N2 VDD33 E3

AS J16 RSV5 E17 RXD27 V15 TXD24 N3 VDD33 F3

CHICLK R16 RSV6 D17 RXD28 U15 TXD25 P1 VDD33 F15

CKSPD0 E18 RSV7 B18 RXD29 T15 TXD26 P2 VDD33 H3

CKSPD1 D16 RSV8 C18 RXD30 V16 TXD27 R1 VDD33 J3

CS J18 RSV9 D18 RXD31 U16 TXD28 R2 VDD33 K16

DATA00 K18 RSV10 T18 TCK G17 TXD29 T1 VDD33 P3

DATA01 K17 RSV11 V17 TDI G16 TXD30 T2 VDD33 R3

DATA02 L18 RXD00 V2 TDO G18 TXD31 U1 VDD33 T5

DATA03 L17 RXD01 U3 TMS G15 VDD15 C5 VDD33 T6

DATA04 L16 RXD02 V3 TRSTN H18 VDD15 C6 VDD33 T9

DATA05 M18 RXD03 U4 TXD00 B1 VDD15 C7 VDD33 T10

DATA06 M17 RXD04 V4 TXD01 C2 VDD15 C12 VDD33 T14

DATA07 M16 RXD05 U5 TXD02 C1 VDD15 C13 VDD33 T17

DATA08 M15 RXD06 V5 TXD03 D2 VDD15 C14 VDDPLL R14

DATA09 N18 RXD07 U6 TXD04 D1 VDD15 D5 NC K3

DATA10 N17 RXD08 V6 TXD05 E2 VDD15 D6 NC T4

DATA11 N16 RXD09 T7 TXD06 E1 VDD15 D7 VSS A1

DATA12 N15 RXD10 U7 TXD07 F2 VDD15 D12 VSS A18

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 9

Symbol Ball Symbol Ball Symbol Ball Symbol Ball Symbol Ball

VSS B2 VSS C8 VSS J9 VSS R4 VSS B3

VSS C11 VSS J10 VSS R5 VSS B4 VSS C15

VSS J11 VSS R6 VSS B5 VSS C16 VSS J15

VSS R9 VSS B6 VSS D3 VSS K4 VSS R10

VSS B7 VSS D4 VSS K8 VSS R15 VSS B8

VSS D8 VSS K9 VSS T3 VSS B9 VSS D11

VSS K10 VSS T12 VSS B10 VSS D15 VSS K11

VSS T13 VSS B11 VSS E4 VSS L3 VSS T16

VSS B12 VSS F4 VSS L8 VSS U2 VSS B13

VSS F16 VSS L9 VSS U17 VSS B14 VSS H8

VSS L10 VSS U18 VSS B15 VSS H9 VSS L11

VSS V1 VSS B16 VSS H10 VSS L15 VSS V18

VSS B17 VSS H11 VSS M3 VSSPLL R13 VSS C3

VSS J4 VSS N4 VSS C4 VSS J8 VSS P4

Table 2-1. Package Ball Assignments in Signal Name Order (continued)

TSI-4

4k x 4k Time-Slot Interchanger Data Sheet, Revision 3

September 21, 2005

10 Agere Systems Inc.

2.3 Package Ball Matrix

2.3.1 Top View

Table 2-2. Package Ball Assignments (Top View)

12 3 4 5 6 7 8 9 1011121314 15 16 17 18

AVSS ADDR15 ADDR14 ADDR13 ADDR12 ADDR11 ADDR10 ADDR09 ADDR08 ADDR07 ADDR06 ADDR05 ADDR04 ADDR03 ADDR02 ADDR01 ADDR00 VSS

BTXD00 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS RSV7

CTXD02 TXD01 VSS VSS VDD15 VDD15 VDD15 VSS VDD33 VDD33 VSS VDD15 VDD15 VDD15 VSS VSS VDD33 RSV8

DTXD04 TXD03 VSS VSS VDD15 VDD15 VDD15 VSS VDD33 VDD33 VSS VDD15 VDD15 VDD15 VSS CKSPD1 RSV6 RSV9

ETXD06 TXD05 VDD33 VSS ——————————

RSV3 RSV4 RSV5 CKSPD0

FTXD08 TXD07 VDD33 VSS ——————————

VDD33 VSS RSV1 RSV2

GTXD11 TXD10 TXD09 VDD15 ——————————

TMS TDI TCK TDO

HTXD13 TXD12 VDD33 VDD15 ———

VSS VSS VSS VSS ———

RESET INT DT TRSTN

JTXD15 TXD14 VDD33 VSS ———

VSS VSS VSS VSS ———VSS AS R/W CS

KTXD16 TXD17 NC VSS — — — VSS VSS VSS VSS — — — MPUCLK VDD33 DATA01 DATA00

LTXD18 TXD19 VSS VDD15 — — — VSS VSS VSS VSS — — — VSS DATA04 DATA03 DATA02

MTXD20TXD21VSSVDD15——————————DATA08DATA07DATA06DATA05

NTXD22TXD23TXD24VSS——————————DATA12DATA11DATA10DATA09

PTXD25TXD26VDD33VSS——————————PAR1DATA15DATA14DATA13

RTXD27 TXD28 VDD33 VSS VSS VSS VDD15 VDD15 VSS VSS VDD15 VDD15 VSSPLL VDDPLL VSS CHICLK HIZ PAR0

TTXD29 TXD30 VSS NC VDD33 VDD33 RXD09 RXD12 VDD33 VDD33 FSYNC VSS VSS VDD33 RXD29 VSS VDD33 RSV10

UTXD31 VSS RXD01 RXD03 RXD05 RXD07 RXD10 RXD13 RXD15 RXD18 RXD20 RXD22 RXD24 RXD26 RXD28 RXD31 VSS VSS

VVSS RXD00 RXD02 RXD04 RXD06 RXD08 RXD11 RXD14 RXD16 RXD17 RXD19 RXD21 RXD23 RXD25 RXD27 RXD30 RSV11 VSS

Data Sheet, Revision 3

September 20, 2005 TSI-4

4k x 4k Time-Slot Interchanger

Agere Systems Inc. 11

2.3.2 Bottom View

Table 2-3. Package Ball Assignments (Bottom View)

12 3 4 5 6 7 8 9 1011121314 15 16 17 18

VVSS RXD00 RXD02 RXD04 RXD06 RXD08 RXD11 RXD14 RXD16 RXD17 RXD19 RXD21 RXD23 RXD25 RXD27 RXD30 RSV11 VSS

UTXD31 VSS RXD01 RXD03 RXD05 RXD07 RXD10 RXD13 RXD15 RXD18 RXD20 RXD22 RXD24 RXD26 RXD28 RXD31 VSS VSS

TTXD29 TXD30 VSS NC VDD33 VDD33 RXD09 RXD12 VDD33 VDD33 FSYNC VSS VSS VDD33 RXD29 VSS VDD33 RSV10

RTXD27 TXD28 VDD33 VSS VSS VSS VDD15 VDD15 VSS VSS VDD15 VDD15 VSSPLL VDDPLL VSS CHICLK HIZ PAR0

PTXD25TXD26VDD33VSS——————————PAR1DATA15DATA14DATA13

NTXD22TXD23TXD24VSS——————————DATA12DATA11DATA10DATA09

MTXD20TXD21VSSVDD15——————————DATA08DATA07DATA06DATA05

LTXD18 TXD19 VSS VDD15 — — — VSS VSS VSS VSS — — — VSS DATA04 DATA03 DATA02

KTXD16 TXD17 NC VSS — — — VSS VSS VSS VSS — — — MPUCLK VDD33 DATA01 DATA00

JTXD15 TXD14 VDD33 VSS — — — VSS VSS VSS VSS — — — VSS AS R/W CS

HTXD13 TXD12 VDD33 VDD15 ———

VSS VSS VSS VSS ———

RESET INT DT TRSTN

GTXD11 TXD10 TXD09 VDD15 ——————————

TMS TDI TCK TDO

FTXD08 TXD07 VDD33 VSS ——————————

VDD33 VSS RSV1 RSV2

ETXD06 TXD05 VDD33 VSS ——————————

RSV3 RSV4 RSV5 CKSPD0

DTXD04 TXD03 VSS VSS VDD15 VDD15 VDD15 VSS VDD33 VDD33 VSS VDD15 VDD15 VDD15 VSS CKSPD1 RSV6 RSV9

CTXD02 TXD01 VSS VSS VDD15 VDD15 VDD15 VSS VDD33 VDD33 VSS VDD15 VDD15 VDD15 VSS VSS VDD33 RSV8

BTXD00 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS RSV7

AVSS ADDR15 ADDR14 ADDR13 ADDR12 ADDR11 ADDR10 ADDR09 ADDR08 ADDR07 ADDR06 ADDR05 ADDR04 ADDR03 ADDR02 ADDR01 ADDR00 VSS

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

1212 Agere Systems Inc.

2.4 Ball Types

This table describes each type of input, output, and I/O ball used in the device.

2.5 Ball Definitions

This section describes the function of each of the device balls. The balls are listed by ball name. The static parameters (drive

currents, switching thresholds, etc.) for each ball type (input, output, etc.) are described in Table 4-1 on page 18 through

Table 4-3.

Table 2-4. Ball Types

Type Label Description

I CMOS input, TTL switching thresholds.

I pd CMOS input, TTL switching thresholds with internal pull-dow n re sist or.

I pu CMOS input, TTL switching thresholds with internal pull-up re sist or.

O CMOS output.

O od Open-drain output.

I/O Bidirectional ball. CMOS input with TTL switching thresholds and CMOS output.

P Power and ground.

Table 2-5. Timing Port

Ball Name Type Name/Description

FSYNC I Frame Synchr on iz at io n . This signal indicates the beginning of a 125 µs frame event (8 kHz). The

FSYNC ball can be programmed as active-low or active-high, but its polarity is the same for all

concentration highway interfaces (CHI). FSYNC can be sa mpled on either the positive or ne gative

edge of CHICLK. T i me-slot numbers an d bit of fset s for e ach CHI are assigne d relative to the de tection

of FSYNC.

CHICLK I Clock. This is the master synchronous clock for the transmit and rece ive concentration highwa ys. The

frequency can be 8.192 MHz or 16.384 MHz. It must be at least as fast as the highest CHI data rate.

CKSPD0 I Clock Speed. Static control input that should be tied according to the frequen cy of CHICLK. If CHICLK

is connected to an 8.192 MHz source, CKSPD0 should be tied to VSS. If CHICLK is connected to a

16.384 MHz source, CKSPD0 should be tied to VDD33.

CKSPD1 I pd Clock Speed. Reserved, leave disconnected. 20 kΩ pull-dow n resistor.

Table 2-6. Transmit and Receive Concentration Highways

Ball Name Type Name/Description

RXD[31:0] I pd Receive Data [31:0]. Receive concentration highways. These are serial, synchronous data streams,

which may be individually programmed to operate at 2.048 Mbits/s, 4.096 Mbits/s, 8.192 Mbits/s, or

16.384 Mbit s/s. They carry 32, 64, 128, or 256 time slots (respectively) each occupying eight

contiguous bits. 20 kΩ pull-down resistor.

TXD[31:0] O Transmit Data [31:0]. These are output concentration highway data streams with data rate options

identical to the RXD inputs.

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 13

Table 2-7. Control Port

Ball Name Type Name/Description

MPUCLK I Processor Clock. This clock is used to sample address, data, and control signals from the

microprocessor. This clock must be within the range of 0 MHz—66 MHz. Required for operation.

CS IChip Select . Active-low chip select. This input is held low for the duration of any read or write access

to the device. Req u ire d fo r op er at ion .

AS IAddress Strobe. Active-low address strobe that is one MPUCLK cycle wide at the start of a

microprocessor access cycle to the device. This is used to initiate a microprocessor access. Required

for operation.

R/W IRead/Write. Cycle selection. R/W is set high during a read cycle, or set low for a write cycle.

Required for operation.

ADDR[15:0] I pu Address [15:0]. ADDR[15] is the most significant bit and ADDR[0] is the least significant bit for

addressing all the internal registers during microprocessor access cycles. All addresses are 16-bit

word addresses; therefore, in a typical application ADDR[0] of the device would be connected to

address bit 1 of a byte addressable system address bus. Require d for operation. 200 kΩ pull-up

resistor.

Note: The device is little-endian; the least significant byte is stored in the lowest address and the

most significant byte is stored in the highest address. Care must be exercised when

connecting to microprocessors that use big-endian byte ordering.

DATA[15:0] I/O Dat a [15:0]. Data bus for all transfers between the microprocessor and th e internal registers. The

balls are inputs during write cycles and outputs during read cycles. DATA[15] is the most significant

bit, and DATA[0] is the least significant bit. Required for operation.

PAR[1:0] I/O Control Port Parity [1:0]. Byte-wide parity bits for data. PAR[1] is the parity for DATA[15:8], and

PAR[0] is the parity for DATA[7:0]. The parity sense (even or odd) is application programmable via a

DT ODat a T ran sfer Acknowledge. Active-l ow for one MPUCLK cycle. Indicates that data has been written

during write cycles or that dat a is valid during rea d cycles. High impedance when CS is a 1 and driven

when CS is 0. Required for operation.

INT O od Interrupt. This output is asserted low to indicate that an interrupt condition has occurred. This signal

remains active-low until the interrupt status register has been cleared or masked.

Table 2-8. Initialization and Test Access

Ball Name Type Name/Description

RESET I pu Reset. Global reset, active-low. Initializes all internal registers to their default state. The reset occurs

asynchronously, but RESET should be held low for at least two CHICLK periods. 20 kΩ pull-up resistor.

TCK I pu Test Clock. This signal provides timing for the boundary-scan and test access port (TAP) controller.

Should be static, except during boundary-scan testing. 20 kΩ pull-up resistor.

TDI I pu Test Data In. Data input for the boundary-scan. Sampled on the rising edge of TCK. 20 kΩ pull-up

resistor.

TMS I pu Test Mode Select ( Active-Low). Co ntrols boundary-scan test o perations. TMS is sampled on the rising

edge of TCK. 20 kΩ pull-up resistor.

TRSTN I pd Test Reset (Active-Low). This signal is an asynchronous reset for the TAP controller. 20 kΩ pull-down

resistor.

TDO O Test Data Out. Updated on the falling edge of TCK. The TDO output is high impedance except when

scanning out test data.

HIZ I pu Output Enable. All output and bidrectional buffers will be high-impedance when this input is low unless

boundary scan is enabled (TRSTN = 1). 20 kΩ pull-up resistor.

RSV[11:1] — Reserved [11:1]. These balls are used by Ager e Systems during the manufa cturing process; the y must

be left unconnected.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

1414 Agere Systems Inc.

Table 2-9. Power Balls

Symbol Type Name/Description

VDD33 PI/O Power. Power supply balls for the I/O pads (3.3 V ± 5%).

VDD15 PCore Power. Power supply balls for the core (1.5 V ± 5%).

VSS PGround. Common gr ound balls for 3.3 V and 1.5 V supplies.

VDDPLL PPLL Power. 1.5 V power supply for the internal phase-locked loop. Must include local 0.01 µF capacitor to

VSSPLL.

VSSPLL PPLL Ground. Isolated ground for the internal phase-locked loop.

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 15

3 Operating Conditions and Reliability

3.1 Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso lu te

stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those

given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended periods ca n

adversely affect device reliability.

3.2 Recommended Operating Conditions

Table 3-2 lists the volt ages, along with the tolerances, that are required for proper operation of the device.

3.3 Handling Precautions

Although electrostatic dischar ge (ESD) pr otection circuitry has been d esigned into this device, prop er pr ecau tions must be

taken to avoid exposure to ESD and electrical overstress (EOS) during all handling, assembly, and test operations. Agere

employs both a human-body model (HBM) and a charged-device model (CDM) qualification requirement in order to deter-

mine ESD-susceptibility limits and protection design evaluation. ESD voltage thresholds are dependent on the circuit param-

eters used in each of the models, as defined by JEDEC’s JESD22-A114 (HBM) and JESD22-C101 (CDM) standards.

Table 3-1. Absolute Maximum Ratings

Parameter Min Max Unit

Supply Voltage (VDD33)–0.54.2V

Supply Voltage (VDD15)–0.51.8V

Input Voltage:

TXD[31:0]

All Other Inputs –0.5

–0.3 5.5

VDD33 + 0.3 V

Storage Tempe ra tu re –40 125 °C

Junction Temperature — 125 °C

Table 3-2. Operating Conditions

Parameter Min Typ Max Unit

Supply Voltage (VDD33) 3.14 3.3 3.47 V

Supply Voltage (VDD15) 1.4 1.5 1.6 V

Ambient Temperature –40 — 85 °C

Table 3-3. ESD Tolerance

Device Voltage Type

TSI-4 2,000 V HBM (human-body model)

500 V CDM (charged-device model)

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

1616 Agere Systems Inc.

3.4 Thermal Parameters (Definitions and Values)

System and circuit board level performance depends not only on device electrical characteristics, but also on device thermal

characteristics. The thermal characteristics frequently determine the li mits of circuit boar d or system performan ce, and they

can be a major cost adder or cost avoidance factor. When the die temper ature is kept belo w 125 °C, temperatur e-activated

failure mechanisms are minimized . The ther mal par am eters that Agere p rovid es for its p ackage s help th e chip and system

designer choose the best package for their applications, including allowing the system designer to thermally design and in-

tegrate their syste m s.

It should be noted that all the pa rameters listed below are affected, to varying degree s, by package design (including paddle

size) and choice of materials, the amount of copper in the test board or system board, and system airflow.

ΘJA - Junction to Air Thermal Resistance

ΘJA is a number used to express the thermal performance of a part under JEDEC standard natural convection co nditions.

ΘJA is calculated using the following formula:

ΘJA = (TJ – Tamb) / P; where P = power

ΘJMA - Junction to Moving Air Thermal Resistance

ΘJMA is effectively identical to ΘJA but represents per formance of a p art mounted on a JEDEC four layer boa rd inside a wind

tunnel with forced air convection. ΘJMA is reported at airflows of 200 LFPM and 500 LFPM (linear feet per minute), which

roughly correspond to 1 m/s and 2.5 m/s (respectively). ΘJMA is calculated using the following formula:

ΘJMA = (TJ – Tamb) / P

ΘJC - Junction to Case Thermal Resistance

ΘJC is the thermal resi stan ce from junction to th e top of the case. Th is number is dete rmined by forcing ne arly 100% of the

heat generated in the die out the top of the package by lowering the top case temperature. This is done by placing the top

of the package in contact with a copper slug kept at room temperature using a liquid refrigeration unit. ΘJC is calculated using

the following formula:

ΘJC = (TJ – TC) / P

ΘJB - Junction to Board Thermal Resistance

ΘJB is the thermal resistance fr om junction to board. This number is determined by forcing the hea t generated in the die out

of the package through the leads or balls by lowering the board temperature and insulating the package top. This is done

using a special fixture, which keeps the board in contact with a water chilled copper slug around the perimeter of the package

while insulating the package top. ΘJB is calculated using the following formula:

ΘJB = (TJ – TB) / P

ΨJT - Junction Temperature to Case Temperature

ΨJT correlates the junction temperature to the case temperature. It is generally used by the customer to infer the junction

temperature while the pa rt is operating in their system. It is no t considered a true therma l resistance. ΨJT is calculated using

the following formula:

ΨJT = (TJ – TC) / P

Table 3-4. Thermal Parameter Values

Parameter Temperature °C/Watt

ΘJA 25.1

ΘJMA (1 m/s) 21.4

ΘJMA (2.5 m/s) 18.8

ΘJC 5.8

ΘJB 13.0

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 17

3.5 Power Consumption

Table 3-5. Power Consumption

Supply Voltage Typ*

* MPUCLK = 66 MHz, CHICLK = 16.384 MHz, TA = 25 °C, all CHIs active, all outputs loaded with 50 pF.

Max

VDD33 100 mW at 3.3 V 150 mW at 3.47 V

VDD15 275 mW at 1.5 V 325 mW at 1.6 V

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

1818 Agere Systems Inc.

4 dc Electrical Characteristics

This section describes all the static parameters associated with all the ball types used in the device.

* Excludes current due to pull-up or pull-down resistors.

Table 4-1. CMOS Inputs

Parameter Symbol Conditions Min Typ Max Unit

Input Leakage Current IIL VSS < VIN < VDD33 —— 1* µA

High-input Voltage VIH —2.0—VDD33 + 0.3 V

Low-input Voltage VIL —–0.3—0.8V

Input Capacitance CI——2.5—pF

Table 4-2. CMOS Outputs

Parameter Symbol Conditions Min Typ Max Unit

Output Voltage Low VOL IOL = –10 mA — — 0.4 V

Output Voltage High VOH IOL = 10 mA 2.4 — — V

Output Current Low IOL ———10mA

Output Current High IOH ———10mA

Output Ca pacitance CO——3—pF

HIZ Output Leakage Current IOZ ———10µA

Table 4-3. CMOS Bidirectionals (DATA[15:0])

Parameter Symbol Conditions Min Typ Max Unit

Leakage Current ILVSS < VIN < VDD33 ——11µA

High-input Voltage VIH —2.0—VDD33 + 0.3 V

Low-input Voltage VIL — –0.3 — 0.8 V

Biput Capacitance CIB — — 5.0 — pF

Output Voltage Low VOL IOL = –10 mA — — 0.4 V

Output Voltage High VOH IOL = 10 mA 2.4 — — V

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 19

5 Timing Diagrams and ac Characteristics

Figure 5-1 and Figu re 5-2 describe the timing specifications for the input clocks

Figure 5-1. CHICLK Timing Specifications

* VIH to VIH or VIL to VIL.

Figure 5-2. MPUCLK Timing Specifications

* VIH to VIH or VIL to VIL.

Table 5-1. CHICLK Timing Specifications

Parameter Description Min Typ Max Unit

t1CHICLK Rise Time — 2 7 ns

t2CHICLK Width (8.192 MHz)* 48.84 — 73.24 ns

t2CHICLK Width (16.384 MHz)* 24.42 — 36.62 ns

t3CHICLK Fall Time — 2 7 ns

t4CHICLK Period (8.192 MHz) — 122.07 — ns

t4CHICLK Period (16.384 MHz) — 61.03 — ns

Table 5-2. MPUCLK Timing Specifications

Parameter Description Min Typ Max Unit

t5MPUCLK Rise Time — 2 7 ns

t6MPUCLK Width* 6.06 — — ns

t7MPUCLK Fall Time — 2 7 ns

t8MPUCLK Period 15.2 — — ns

t1VDD33

VIL

VIH VIH

VIL

50%

t5VDD33

VIL

VIH VIH

VIL

50%

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

2020 Agere Systems Inc.

Figure 5-3 shows the ac timing specifications for the CMOS outputs on the device.

Figure 5-3. ac Timing Specification

* Test load = 50 pF (total).

Table 5-3. CMOS Output ac Timing Specification *

Parameter Description Min Typ Max Unit

t9Rise Time (20%—80%) — 1.5 7 ns

t10 Fall Time (80%—20%) — 1.5 7 ns

20%

80 %

20 %

80 %

t9 t10

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 21

Note: This figure assumes the device is programmed to sample FSYNC on the rising edge of CHICLK.

Figure 5-4. CHI Interface Timing

* Applies if Driver_Enable_Control = 01. For Driver_Enable_Control = 11 refer to Figure 5-15, CHI 3-State Output Control on page 27.

All timing specifications apply under the following conditions:

If FS is active-low.

If the falling edge of CHICLK is specified as the active edge.

At all RXD and TXD rates (16.384 Mbits/s, 8.192 Mbits/s, 4.096 Mbits/s, or 2.048 Mbits/s) with a CHICLK frequency of

16.384 MHz or 8.192 MHz.

Table 5-4. CHI Interface Timing

Parameter Description Min Max Unit

t13 FSYNC Setup Time to Active CHICLK Edge 10 — ns

t14 FSYNC Hold Time from Active CHICLK Edge 5 — ns

t15 RXD Setup to Active CHICLK Edge 10 — ns

t16 RXD Hold Time from Active CHICLK Edge 5 — ns

t17 TXD High Z to Data Valid — 15 ns

t18 TXD Propagation Delay from Active CHICLK Edge 2 12 ns

t19 Transmit Data High Impedance* — 15 ns

TXD

CHICLK

RXD

FSYNC

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

2222 Agere Systems Inc.

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-5. Typical Receive CHI Timing with 16.384 Mbits/s Data and 16.384 MHz CHICLK

Notes:

1/4 bit offset not valid with 16 Mbits/s data.

For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the

CHICLK.

Figure 5-6. Transmit CHI Timing with 16.384 Mbits/s Data and 16.384 MHz CHICLK

FSYNC

CHICLK

w/ 0 offse

da ta s a m p le d

w/ ¼ bit offse

data sampled

w/ ½ bit offse

d a ta sa m pled

w/ ¾ bit offse

d a ta s a m p le d

w/ bit offset = 1 da ta s a m p le d

w/ 2¾ bit offset da ta sa mple d

w/ bit offset = 7 da ta s a m p le d

da ta s a m p le d

data sampled

d a ta s a m p le d

w / TS offset = 1,

bit offset = 0 TS254 B

TS254 B

TS255 B

TS0 B 1

TS0 B 0TS255 B1 TS255 B

TS255 B

TS0 B 4 TS0 B 5

TS254 B

TS255 B

TS255 B1 TS255 B

TS25 5 B

TS255 B

TS0 B 0 TS0 B 1 TS0 B 2 TS 0 B 3

TS255 B

TS25 5 B

TS0 B 0 TS0 B 1 TS0 B 2 TS0 B 3 TS0 B 4 TS0 B 5

TS25 5 B

TS255 B

TS0 B 0 TS0 B 1 TS0 B 2 TS0 B 3 TS0 B 4 TS0 B 5

TS25 5 B

TS255 B

TS0 B0 TS0 B 1 TS0 B 2 TS0 B 3

TS255 B

TS25 5 B

TS255 B

TS0 B 0

w/ TS offset = 13,

bit offset = 3

TS242 B

TS24 2 B

TS242 B

TS243 B

TS24 3 B

TS24 2 B

TS242 B

TS243 B

TS243 B1

TS255 B

TS0 B0

TS243 B

TS24 3 B

TS0 B 5 TS0 B 6TS0 B3 TS0 B4

TS0 B1 TS0 B 2 TS0 B 3

TS0 B7 TS1 B0TS0 B 1 TS0 B 2

w / TS offset = 255,

bit offset = 7

TS25 5 B

TS0 B 4TS0 B 0

TS255 B

TS0 B0 TS0 B 1 TS0 B2 TS0 B 3 TS0 B 4 TS0 B5

FSYNC

CHICLK

w/ 0 offset

w/ ½ bit offset

w/ bit offset = 1

w/ TS offset = 255,

bit offs et = 7½ TS255 B6 TS255 B7 TS0 B0

w/ TS offset = 1,

bit offset = 0

TS0 B2 TS0 B3 TS0 B4

TS254 B5 TS254 B6 TS254 B7 TS255 B0

TS255 B4 TS255 B5

TS0 B3 TS0 B4

TS255 B1 TS255 B2 TS255 B3

TS0 B0 TS0 B1

TS255 B4 TS255 B5

TS255 B5 TS255 B6 TS255 B7 TS0 B0

TS0 B3 TS0 B4 TS0 B5

TS0 B5

TS0 B1 TS0 B2

TS255 B6 TS255 B7

TS255 B5 TS255 B6 TS255 B7 T S0 B0 TS0 B1 TS0 B2 TS0 B3 TS0 B4

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 23

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-7. Typical Receive CHI Timing with 8.192 Mbits/s Data and 16.38 4 MHz CHICLK

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-8. Transmit CHI Timing with 8.192 Mbits /s Data and 16.384 MHz CHICLK

FSYNC

CHICLK

w/ 0 offset data sampled

w/ ¼ bit offset data sampled

w/ ½ bit offset data sampled

w/ ¾ bit offset data sampled

w/ bit offset = 1 data sampled

w/ 2¾ bit offset data sampled

w/ bit offset = 7 data sampled

data sampled

data sampled TS0 B2 TS0 B3 TS0 B4

w/ TS offset = 127,

bit offset = 7¾ TS 127 B7 T S0 B0 TS0 B1

TS127 B2 TS127 B3 TS127 B4

w/ TS offset = 13,

bit offset = 3¼ TS114 B4 TS114 B5 TS114 B6 TS114 B7 TS115 B0 TS115 B1

w/ TS offset = 1,

bit offset = 0 TS126 B7 TS127 B0 TS127 B1

TS127 B4 TS127 B5

TS 127 B4 TS127 B5

TS127 B0 TS127 B1 TS127 B2 TS127 B3

TS127 B6 TS127 B7

TS0 B2 TS0 B3

TS0 B0 TS0 B1

TS127 B6 TS127 B7 TS0 B0 TS0 B1

TS 127 B6 TS127 B7 TS0 B0 TS0 B1

TS0 B3 TS0 B4

TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3

TS127 B7 TS0 B0 TS0 B1 TS0 B2

TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3 TS0 B4

FSYNC

CHICLK

w/ 0 offset

w/ ¼ bit offset

w/ ½ bit offset

w/ bit offset = 1

TS 127 B6 TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3

TS0 B2 TS0 B3

TS127 B6 TS127 B7 TS0 B0 TS0 B1 TS0 B2

TS127 B6 TS127 B7 TS0 B0 TS0 B1

TS 127 B5 TS127 B6 TS127 B7 TS0 B0

w/ TS offset = 1,

bit offset = 0

TS127 B7 TS0 B0 TS0 B1

w/ TS offset = 127,

bit offset = 7¾

TS 126 B6 TS126 B7 TS127 B0 TS127 B1

TS0 B2 TS0 B3

TS0 B1 TS0 B2

TS127 B2 TS127 B3

TS0 B3

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

2424 Agere Systems Inc.

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-9. Typical Receive CHI Timing with 4.096 Mbits/s Data and 16.38 4 MHz CHICLK

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-10. Transmit CHI Timing with 4.096 Mbits/s Data and 16.384 MHz CHICLK

FSYNC

CHICLK

w/ 0 offset data sampled

w/ ¼ bit offset data sampled

w/ ½ bit offset data sampled

w/ ¾ bit offset data sampled

w/ bit offset = 1 data sa mpled

w/ 2¾ bit offset data sample d

w/ bit offset = 7 data sa mpled

data sampled

TS50 B7

w/ TS offset = 63,

bit offset = 7¾ TS0 B0 TS0 B1 TS0 B2

w/ TS offset = 13,

bit offset = 3¼ TS50 B4 TS50 B5 TS50 B6

w/ TS offset = 1,

bit offset = 0 TS63 B0 TS63 B1 TS63 B2

TS63 B5 TS63 B6 TS63 B7

TS63 B1 TS63 B2 TS63 B3

TS63 B7 TS0 B0 TS0 B1

TS63 B7 TS0 B0 TS0 B1 TS0 B2

TS0 B0 TS0 B1 TS0 B2

TS63 B7 TS0 B0 TS0 B1 TS0 B2

FSYNC

CHICLK

w/ 0 offset

w/ ¼ bit offset

w/ ½ bit offset

w/ bit offset = 1

w/ TS offset = 63,

bit offset = 7¾

TS62 B7 TS63 B0 TS63 B1

w/ TS offset = 1,

bit offset = 0

TS63 B6 TS63 B7 TS0 B0

TS63 B7 TS0 B0 TS0 B1 TS0 B2

TS63 B6 TS63 B7 TS0 B0 TS0 B1

TS63 B7 TS0 B0 TS0 B1

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 25

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-11. Typical Receive CHI Timing with 2.048 Mbits/s Data and 16.384 MHz CHICLK

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-12. Transmit CHI Timing with 2.048 Mbits/s Data and 16.384 MHz CHICLK

FSYNC

CHICLK

w/ 0 offset data sampled

w/ ¼ bit offset data sampled

w/ ½ bit offset data sampled

w/ ¾ bit offset data sampled

w/ bit offset = 1 data sampled

w/ 2¾ bit offset data sampled

w/ bit offset = 7 data sampled

data sampled

w/ TS offset = 31,

bit offset = 7¾ TS0 B0 TS0 B1 TS0

w/ TS offset = 1,

bit offset = 0 TS31 B 0 TS31 B1

w/ TS offset = 13,

bit offset = 3¼ TS18 B5 TS18 B6

TS31 B 5 TS31 B6 TS31

TS31 B 1 TS31 B2

TS31 B 7 TS0 B0 TS0

TS31 B 7 TS0 B0

TS0 B0 TS0 B1

TS31 B7 TS0 B0 TS0 B1

FSYNC

CHICLK

w/ 0 offset

w/ ¼ bit offset

w/ ½ bit offset

w/ bit offset = 1

TS30 B7 TS31 B0 TS31 B01

w/ TS offset = 1,

bit offset = 0

TS31 B7 TS0 B0 TS0 B1

w/ TS offset = 31,

bit offset = 7¾

TS31 B7 TS0 B0

TS31 B6 TS31 B7 TS 0 B0

TS31 B7 TS0 B0 TS0 B1

TS31 B7 TS0 B 0

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

2626 Agere Systems Inc.

Note: For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the CHICLK.

Figure 5-13. Typical Receive CHI Timing with 8.192 Mbits/s Data and 8.192 MHz CHICLK

Notes:

1/4 bit offset not valid with 8 MHz data and 8 MHz clock.

For this timing diagram, it is assumed that FSYNC has been programmed to be active-high, and to be sampled by the rising edge of the

CHICLK.

Figure 5-14. Transmit CHI Timing with 8.192 Mbits/s Data and 8.192 MHz CHICLK

FSYNC

CHICLK

w/ 0 offset data sampled

w/ ¼ bit offset data sampled

w/ ½ bit offset data sampled

w/ ¾ bit offset data sampled

w/ bit offset = 1 data sampled

w/ 2¾ bit offset data sampled

w/ bit offset = 7 data sampled

data sampled

data sampled TS0 B5 TS0 B6 TS0 B7 TS1 B0TS0 B1 TS0 B2 TS0 B3 TS0 B4

w/ TS offset = 127,

bit offset = 7¾ TS127 B6 TS127 B7 TS0 B0

TS115 B2 TS115 B3 TS115 B4 TS115 B5TS114 B6 TS114 B7 TS115 B0 TS115 B1

w/ TS offset = 13,

bit offset = 3¼ TS114 B3 TS114 B4 TS114 B5

TS127 B5 TS127 B6 TS127 B7 TS0 B0

TS0 B 0 TS0 B1

w/ TS offset = 1,

bit offset = 0 TS126 B6 TS126 B7 TS127 B0 TS127 B1 TS127 B2 TS127 B3 TS127 B4

TS0 B3

TS126 B7 TS127 B0 TS127 B1 TS127 B2 TS127 B3 TS127 B4 TS127 B5 TS127 B6 TS127 B7

TS127 B7 TS0 B0 TS0 B1 TS0 B2TS127 B3 TS127 B4 TS127 B5 TS127 B6

TS0 B5

TS127 B5 TS127 B6 TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3 TS0 B4

TS0 B1 TS0 B2 TS0 B3 TS0 B4TS127 B5 TS127 B6 TS127 B7 TS0 B0

TS0 B2 TS0 B3 TS0 B4 TS0 B5TS127 B6 TS127 B7 TS0 B0 TS0 B1

TS127 B6 TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3 TS0 B4 TS0 B5

FSYNC

CHICLK

w/ 0 offset

w/ ½ bit offset

w/ bit offset = 1

TS127 B5

w/ TS offset = 127,

bit offset = 7½ TS127 B6 TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3 TS0 B4 TS0 B5

TS0 B4

w/ TS offset = 1,

bit offset = 0 TS126 B5 TS126 B6 T S126 B7 TS127 B0 TS127 B1 TS127 B2 TS127 B3 T S127 B4

TS0 B0 TS0 B1 TS0 B2 TS0 B3TS127 B4 TS127 B5 TS127 B6 TS127 B7

TS0 B1 TS0 B2 TS0 B3 TS0 B4TS127 B5 TS127 B6 TS127 B7 TS0 B0

TS127 B5 TS127 B6 TS127 B7 TS0 B0 TS0 B1 TS0 B2 TS0 B3 TS0 B4 TS0 B5

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 27

Figure 5-15. CHI 3-State Output Control

Table 5-5. CHI 3-State Output Control

Control in the table below refers to bits [6:4] in Table 6-51 Transmit_CHI_Global_Configuration (Read/Write) on page 52.

This only applies if bits 13 and 12 of the corresponding register in Table 6-48 Transmit_CHI_Configuration (Read/Write) on

page 50 are set to 11.

Parameter Control Reference Point*

* Like edge is the reference edge (rising or falling) as defined by bit 0 in Table 6-51 Transmit_CHI_Global_Configur ation (Read/Write) on page 52.

Min Max*Unit

t20 000 After Previous Like Edge in 16 MHz 50 59 ns

001 After Previous Like Edge in 16 MHz 44 53 ns

010 After Previous Like Edge in 16 MHz 38 47 ns

011 After Previous Like Edge in 16 MHz 32 41 ns

t21 000 After Previous Opposite Edge in 8 MHz 50 59 ns

001 After Previous Opposite Edge in 8 MHz 44 53 ns

010 After Previous Opposite Edge in 8 MHz 38 47 ns

011 After Previous Opposite Edge in 8 MHz 32 41 ns

t22 100 After Previous Like Edge (8 MHz mode only) 111 120 ns

101 After Previous Like Edge (8 MHz mode only) 105 114 ns

110 After Pre vio us Like Edge (8 MHz mode only) 99 108 ns

111 After Previous Like Edge (8 MHz mode only) 93 102 ns

CHICLK

16.384 MHz

TXD

16.384 Mbits/s

CHICLK

8.192 MHz

TXD

8.192 Mbits/s

CHICLK

8.192 MHz

TXD

8.192 Mbits/s

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

2828 Agere Systems Inc.

Figure 5-16. Microprocessor Port Timing—Read Cycle

Table 5-6. Microprocessor Port Timing—Read Cycle

Parameter Description Min Max Unit

t23 Address Setup 5 — ns

t24 Address Hold 1 — ns

t25 Chip Select Setup 5 — ns

t26 Chip Select Hold 1 — ns

t27 Address Strobe Setup 5 — ns

t28 Address Strobe Hold 1 — ns

t29 R/W Setup 5 — ns

t30 R/W Hold 1 — ns

t31 Data Output Enable — 15 ns

t32 Data Clock to Valid 1 7 ns

t33 Data High Impedance — 8 ns

t34 DT High Impedance to Valid 1 15 ns

t35 DT Clock to Out 1 7 ns

t36 DT Valid to High Impedance 1 8 ns

MPUCLK

DATA[15:0]

PAR[1:0]

ADDR[15:0]

R/W

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 29

Figure 5-17. Microprocessor Port Timing—Write Cycle

Note: Posted writes follow the same timin g shown in Figure 5-17 on page 29 and Table 5-7 on page 29. A posted write may

return a DT prior to the de vice completing the write cycle. This allows the microprocessor to continue operation while

the device completes the write.

Table 5-7. Microprocessor Port Timing—Write Cycle

Parameter Description Min Max Unit

t37 Address Setup 5 — ns

t38 Address Hold 1 — ns

t39 Chip Select Setup 5 — ns

t40 Chip Select Hold 1 — ns

t41 Address Strobe Setup 5 — ns

t42 Address Strobe Hold 1 — ns

t43 R/W Setup 5 — ns

t44 R/W Hold 1 — ns

t45 Data Setup 5 — ns

t46 Data Hold 1 — ns

t47 DT High Impedance to Valid 1 15 ns

t48 DT Clock to Out 1 7 ns

t49 DT Valid to High Impedance 1 8 ns

MPUCLK

DATA[15:0]

PAR[1:0]

ADDR[15:0]

R/W

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

3030 Agere Systems Inc.

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 31

6 Register Description

This section describes the purpose and operation of each register bit, its dependencies, and its initial state.

6.1 Device Addressing Notes

All device addresses shown are physical byte offset addresses in the microprocessor space, not the actual addresses in the

device itself. The device uses 217 bytes of address spectrum.

The following assumptions are made:

The device is connected to th e microp rocessor as a 16-bit word accessed device (not byte addre ssable), with ADDR[00]

connected to ad dr e ss bi t 1 of the mic ro pr o ces so r.

The microprocessor’s address bit 0 (high/low byte) is not used by the device.

Note: All addresses are expressed in hexadecimal. Unless otherwise indicated by a 0x, register bit states (in default sta tes)

are expressed in binary.

6.2 Acronyms Used

CS—Connection stor e.

CSG—Connection store generator.

PLL—Phas e -locked loo p .

SF—Switch fabric.

TPG—Test pattern generator.

TPM—Test pattern monitor.

VCO—Voltage-controlled oscillator.

6.3 Address Map

Note: The address space is expressed in decimal. Because ADDR[00] on the device is connected to ADDR[01] on the mi-

croprocessor, the device only occupies even addresses in the microprocessor address space.

Table 6-1. Address Map

Global Control 512 0x00000—0x003FE

Connection Store Generator 256 0x00400—0x005FE

Test Pattern Generator and Mon ito r 256 0x00600—0x007FE

Reserved 256 0x00800—0x009FE

CHI Control 896 0x00A00—0x010FE

Switch Fabric Control 1,920 0x01100—0x01FFE

Reserved 4,096 0x02000—0x03FFE

Reserved 24,576 0x04000—0x0FFFE

Connection Store 16,364 0x10000—0x17FFE

Reserved 16,324 0x18000—0x1FFFE

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

3232 Agere Systems Inc.

6.4 Register Summary

Table 6-2. Global Registers

Address Register Access Mode

0x00000 Version_Control Read Only

0x00002 Chip_Identity Read Only

0x00004 Summary_Interrupt_Status Read Only

0x00006 Summary_Interrupt_Mask Read/Write

0x00008 CPU_Access_Error CORWN*

* Clear-on-read/clear-on-write.

0x0000A CPU_Access_Error_Mask Read/Write

0x0000C Global_Control Read/Write

0x0000E PLL_Control Read/Write

0x00010 Power_Control Read/Write

0x00012 Invalid_Address_Trap Read Only

0x00014 Scratch_Register Read/Write

Table 6-3. Connection Store Generator Re gisters

Address Register Access Mode

0x00400 CSG_Control Read/Write

0x00402 CSG_Status Read Only

0x00404 CSG_Starting_Address Read/Write

0x00406 CSG_Ending_Address Read/Write

0x00408 CSG_Write_Enable_Low Read/Write

0x0040A CSG_Write_Enable_High Read/Write

0x00410 CSG_Seed_Low Read/Write

0x00412 CSG_Seed_High Read/Write

0x00418 CSG_OR_Mask_Low Read/Write

0x0041A CSG_OR_Mask_High Read/Write

0x0041C CSG_AND_Mask_Low Read/Write

0x0041E CSG_AND_Mask_High Read/Write

0x00428 CS_Stream_Control Read/Write

0x0042A CSG_Configuration Read/Write

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 33

Table 6-4. Test Pattern Generator and Monitor Registers

Address Register Access Mode

0x00600 TPG_Configuration Read/Write

0x00602 TPG_User_Pattern Read/Write

0x00604 TPM_Configuration Read/Write

0x00606 TPM_User_Pattern Read/Write

0x00608 TPM_Error_Count Sat/Roll*

* Saturate/rollover.

0x0060A TPG_Inject_Error_Count Write Only

0x0060C TPG_Data_Invert_Mask Read/Write

0x0060E TPM_Status Read Only

0x00610 TPM_Status_Mask Read/Write

Table 6-5. Concentration Highway Configuration Registers

Address Register Access Mode

0x00A00—0x00A3E Receive_CHI_Configuration Read/Write

0x00A80 Receive_CHI_Status CORWN*

* Clear-on-read/clear-on-write.

0x00A82 Receive_CHI_Status_Mask Read/Write

0x00A84 Receive_CHI_Global_Configuration Read/Write

0x00C00—0x00C3E Transmit_CHI_Configuration Read/Write

0x00C80 Transmit_CHI_Status CORWN*

0x00C82 Transmit_CHI_Status_Mask Read/Write

0x00C84 Transmit_CHI_Global_Configuration Read/Write

0x01000—0x0103E Receive_CHI_Time_Slot_Offset Read/Write

0x01080—0x010BE Transmit_CHI_Time_Slot_Offset Read/Write

Table 6-6. Switch Fabric Control

Address Register Access Mode

0x01124 SF_Status CORWN*

* Clear-on-read/clear-on-write.

0x01126 SF_Status_Mask Read/Write

0x01142 Data_Store_Time_Slot_Capture_Select Read/Write

0x01144 Data_Store_Captured_Data Read Only

0x01146 Connection_Store_Parity_Error_Address_Trap CORWN*

0x01148 Receive_Link_Offset Read Only

0x0114C Transmit_Link_Offset Read/Write

0x0114E Wide_Mode_Control Read/Write

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

3434 Agere Systems Inc.

Table 6-8. Reserved Registers

The following register will not cause an Invalid_Address_Error (see Table 6-13 on page 36) and are reserved.

6.5 Global Control Registers

The default field indicates the state of each register bit following a hardware or software reset cycle.

These registers are located at the top level of the design and are used to determine operations that affect more than one

block within the device. These could be registers required for control of the microprocesso r port block or register functions

that are not naturally associated with other blocks. Global resets and output enables are included in this section.

Table 6-7. Connection Store

Address Register Access Mode

0x10000—0x17FFC Low_Control_Word Read/Write

0x10002—0x17FFE High_Control_Word Read/Write

Address Register Access Mode

0x00016 Reserved_0 Read/Write

Table 6-9. Version_Control (Read Only)

Address Bit Name/Description Default

0x00000 15 Reserved. 0

14:12 Version_Number. TSI version number. TSI version register will change each time the

device is changed. 001

11:0 Agere_Systems_Identification_Number. This is the ID code assigned to Agere Systems

Inc. by the JTAG standards body. 0x190

Table 6-10. Chip_Identity (Read Only)

Address Bit Name/Description Default

0x00002 15:0 Chip_Identity. This register contains the unique identification code for the device. 0x26D1

Data Sheet, Revision 3 TSI-4
September 21, 2005 4k x 4k Time-Slot Interchanger
Agere Systems Inc .  35
Table 6-11. Summary_Interrupt_Status (Read Only)
Address Bit Name/Description Default
0x00004 15:6 Unused. —
5Transmit_CHI_Interrupt. Active-high flag indicating an unmasked error or status is present 
in the Transmit_ CHI_Status register (see Table 6-49 on page 51).
0 = No transmit CHI error(s) detected.
1 = Transmit CHI Error(s) detected.
—
4Receive_CHI_Interrupt. Active-high flag indicating that an unmasked error or status is 
present in the Receive_CHI_Status register (see Table 6-45 on page 48).
0 = No receive CHI error(s) detected.
1 = Receive CHI error(s) detected.
—
3Unused. —
2TPM_Interrupt. Active-high flag indicating an unmasked error or status is present in the 
TPM_Status register (see Table 6-42 on page 47 ).
0 = No test pattern monitor error(s) detected.
1 = Test pattern error(s) detected.
—
1SF_Interrupt. Active-high flag  indicating an unmasked erro r is present in th e SF_Status reg-
ister (see Table 7-1 on page 54).
0 = No switch fabric error( s) de te ct ed .
1 = Switch fabric error(s) detected.
—
0CPU_Access_Interrupt. Active-high flag ind icating an unmasked error has been detected 
by the CPU_Access_Error register (see Table 6-13 on  page 36).
0 = No microprocessor access error(s) detected.
1 = Microprocessor acce ss error(s) detected.
—
Table 6-12. Summary_Interrupt_Mask (Read/Write)
Address Bit Name/Description Default
0x00006 15:6 Unused. —
5Transmit_CHI_Interrupt_Mask.
0 = The Transmit_CHI_Interrupt bit (see Table 6-11) will cause an interrupt if active.
1 = The Transmit_CHI_Interrupt bit is blocked from causing an interrupt.
1
4Receive_CHI_Interrupt_Mask.
0 = The Receive_CHI_Interrupt bit (see Table 6-11) will cause an interrupt if active.
1 = The Receive_CHI_Interrupt bit is blocked from causing an interrupt.
1
3Unused. —
2TPM_Interrupt_Mask.
0 = The TPM_Interrupt bit (see Table 6-11) will cause an interrupt if active.
1 = The TPM_Interrupt bit is blocked from causing an interrupt.
1
1SF_Interrupt_Mask.
0 = The SF_Interrupt bit will (see Table 6-11) cause an interrupt if active.
1 = The SF_Interrupt bit is blocked from causing an interrupt.
1
0CPU_Access_Interrupt_Mask.
0 = The CPU_Access_Interrupt bit (see Table 6-11) will cause an interrupt if active.
1 = The CPU_Access_Interrupt bit is blocked from causing an interrupt.
1

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

3636 Agere Systems Inc.

Table 6-13. CPU_Access_Error (CORWN)

Address Bit Name/Description Default

0x00008 15:4 Unused. —

3PLL_Lock_Error. This bit indicates if the device's master PLL is locked to the incoming CHI

reference clock (CHICLK).

0 = Locked.

1 = Not locked.

—

2Access_Time_Out_Error.

0 = No time-out.

1 = Indicates that a time-o ut ha s oc cur re d inter n al to the TF RA8 4 J1 3 de vice on a

microprocessor access.

—

1Invalid_Address_Error.

0 = No invalid address.

1 = Indicates th at a microproce ssor access to an invalid add ress has occurred. The address

causing this error can be fo und in the Invalid_Addr ess_Trap register (see Table 6-18 on

page 38).

—

0Data_Parity_Error.

0 = No data parity error.

1 = Indicates that a micro p ro ce sso r da ta bus parity error has occ ur re d .

—

Table 6-14. CPU_Access_Error_Mask (Read/Wr ite)

Address Bit Name/Description Default

0x0000A 15:4 Unused. —

3PLL_Lock_Error_Mask.

0 = The PLL_Lock_Error bit (see Table 6-13) will cause an interrupt if active.

1 = The PLL_Lock_Error bit is blocked from causing an interrupt.

2Access_Time-out_Error_Mask.

0 = The Access_Time_Out_Error bit (see Table 6-13) will cause an interrupt if active.

1 = The Access_Time_Out_Error bit is blocked from causing an interrupt.

1Invalid_Address_Error_Mask.

0 = The Invalid_Address_Error bit will (see Table 6-13) caus e an interrupt if active.

1 = The Invalid_Address_Error bit is blocked from causing an interrupt.

0Data_Parity_Error_Mask.

0 = The Data_Parity_Error bit will (see Table 6-13) cause an interrupt if active.

1 = The Data_Parity_Error bit is blocked from causing an interrupt.

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 37

Table 6-15. Global_Control (Read/Write)

Address Bit Name/Description Default

0x0000C 15 Software_Reset. This bit forces and holds the device in reset.

0 = Normal.

1 = Reset.

14:9 Unused. —

8Reserved. —

7:5 Unused. —

4DT_Wait_State_Control. During write posting, a data transfer acknowledge (DT) can be

generated on the first or second cycle following address strobe. If a DT immediately following

address strobe is too fast for t he micr op ro ce ss or, then a single wait-state can be inse rte d.

0 = Zero wait-states inserted.

1 = One wait-state inserted.

3Write_Posting_Enable. This bit enables write posting, which will provide an early DT to the

microprocessor.

0 = Write postin g disabled.

1 = Write posting enabled.

2Saturate_Rollover_Select. This control bit changes the behavior of event counter registers. In

saturation mode , a register wi ll stick at the maximum value once it is reached. In r oll-over mode,

an event register will continue counting as its value cycles back to zero.

0 = Roll over.

1 = Saturation.

When in saturate mode, the counters will operate in a clear-on-read mode. When in the roll-over

mode, the counters will not be directly writable.

1Data_Parity_Mode. This bit controls the parity setting and checking on the microprocessor data

bus.

0 = Even parity on microprocessor byte data/parity bus.

1 = Odd parity on microprocessor byte data/parity bus.

0Register_Clearing_Mode. This bit controls the way clearing is performed on status bits in clear-

on-read/clear-on-write registers.

0 = The status bit is cleared by writi ng a 1 to it.

1 = The status bit is cleared when a microprocessor read is performed.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

3838 Agere Systems Inc.

Table 6-16. PLL_Control (Read/Write)

This register provides control over the PLL filter parameters. This re gister is unaffected by software reset.

Table 6-17. Power_Control (Read/W r ite)

To minimize power consumption when parts of the device are not used in any given application, individual sections of the

device may be powered off.

Note: All contents and information in a section that is powered off may be lost.

Address Bit Name/Description Default

0x0000E 15:11 Unused. —

10 Reserved. —

9:7 Loop_Filter_Resistor. These bits provide loop filter resistor control over the PLL. The loop

filter damping resistor is ap proximately (Loop_Filter_Resistor + 1) x (20 kΩ). This field is only

enabled if Enable_PLL_Control is set to a 1. If Enable_PLL_Control is set to 0, default val-

ues are used within the PLL.

000

6:4 VCO_Gain_Control. These bits provide control over the VCO gain in the PLL. The gain is

approximately (VCO_Gain_Control x 100 MHz/V). This field is only enabled if

Enable_PLL_Control is set to 1. If Enable_PLL_Control is set to 0, default values are used

within the PLL.

000

3:1 Charge_Pump_Current. These bits provide control over th e charge pump in the PLL.

Charge_Pump_Current is approximately (Charge_Pump_Current + 1) x (2 µA). This field is

always enabled. The typical value is 0x4.

100

0Enable_PLL_Control. This bit is the master control for user programmability of the PLL loop

parameters . If s et to 1 , th e VCO_Gain_Con trol and Loop_Filter _Resistor bi t fiel ds in this reg -

ister are allowed to serv e as loop filter param e te rs for the PLL. If set to 0, these fields are ig-

nored and the PLL uses default values.

0 = Disable user loop parameters.

1 = Enable user loop parameters.

Address Bit Name/Description Default

0x00010 15:1 Unused. —

0Data_Store_Enable. This bit enables the data store. For low-power mode, the data store can

be disabled. However, if the CHI interface is used, this bit should be set to 1. If none of the

CHIs are used, this bit can be set to 0 to save power.

0 = Data store disabled.

1 = Data store enabled.

Table 6-18. Invalid_Address_Trap (Read Only)

Address Bit Name/Description Default

0x00012 15:0 Invalid_Address. This register traps the value of an invalid address during a microproces-

sor access. —

Table 6-19. Scratch_Register (Read/Write)

Address Bit Name/Description Default

0x00014 15:0 Scratch_Pad. This register is for test and diagnostics purposes. It is not connected to an y

internal functions. Therefore, it can be used during early testing to est ablish that th e connec-

tions between the device and the microprocessor are intact, without affecting the configura-

tion of the device.

0x0000

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 39

Table 6-20. Reserved_0 (Read/Writ e)

This register is reserved for use by Agere Systems.

6.6 Connection Store Generator Registers

The connection store is not initialized on powerup nor reset. Although it can be manually initialized by writing all locations

via the microprocessor interface, the CSG is provided to independently fill the connection store with known data. The user

can program the CSG to fill with a variety of patterns or with user-defined fixed data. Since the connection store is greater

than 16 bits wide, the CSG, in general, has pairs of registers associated with controlling the data to be loaded.

Table 6-21. CSG_Control (Read/Write)

This register provides general control over the CSG.

Address Bit Name/Description Default

0x00016 15:3 Unused. —

2Reserved. —

1:0 Unused. —

Address Bit Name/Description Default

0x00400 15:4 Unused. —

3Enable_Stream_Switching. Controls the enable for filling the Stream_Select field of the con-

nection store.

0 = S tream switching is disabled. The S tream_Select field of the connection store RAM is filled

with pseudorandom data.

1 = Enables stream switching. The Stream_Select fields of the connection store is filled with

the contents of CS_Source_Stream_Select (see Table 6-33 on page 42) for all time slots

associated with the stream specified in CS_Destination_Stream_Select (see Table 6-33).

Note: In this mode, all other connection store RAM locations are filled with N-to-N mapping.

2LFSR_Seed_Control. Selects user-definable seed value or predefined seed value for the

pseudorandom pattern generator.

0 = Default seed is loaded into the linear feedback shift register (LFSR) (0x3FFFFFFF).

1 = The 31-bit LFSR is loaded with the contents of the CSG_Seed registers.

1CSG_Mode_Select. Defines the type of pattern that will be filled into the connection store.

0 = Channel N to channel N mapping.

1 = Pseudorandom generated bit pattern (8-bit LFSR).

0CSG_Enable. Enables the pattern generator. After setting the other CSG registers, setting this

bit to a 1 triggers the CSG to start programming of the connection store RAM.

0 = Pattern generator off.

1 = Pattern generator on.

Note: During the CSG operation, the function of the switch fabric is halted and the o utputs of

the CHIs and HSLs are nondeterministic. To reuse the CSG for subsequent

programming of the connection store, this bit must be set back to 0 then to a 1.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

4040 Agere Systems Inc.

Table 6-22. CSG_Status (Read Only)

This register provides general status of the connection store generator.

Table 6-23. CSG_Starting_Address (Read/Write)

This register defines the starting addres s of the connection store RAM for the CSG.

Table 6-24. CSG_Ending_Address (Read/Write)

This register defines the ending address of the connection store RAM for the CSG.

Table 6-25. CSG_Write_En able_Low (Read/Write)

This register provides write enable control on a per-bit basis for the low word of the connection store when using the CSG

to fill the connection store RAM.

Table 6-26. CSG_Write_Enable_High (Read/Write)

This register provides write enab le cont rol on a p er-bit basis fo r the high word of the connection stor e when usin g the CSG

to fill the connection store RAM.

Address Bit Name/Description Default

0x00402 15:1 Unused. —

0CSG_Operation_Complete. Pattern generation for connectio n and data store is complete.

The bit is normally asserted, but it is deasserted when the CSG update is in progress. This

status bit is cleared when the CSG_Enable bit (see Table 6-21) is cleared.

0 = Pattern generator is busy.

1 = Pattern generation is finished.

—

Address Bit Name/Description Default

0x00404 15:13 Unused. —

12:0 CSG_Start_Address. Connection stor e up dates wil l start at this address. To apply the star t

address to a single CS memory, disable the bit write enable register bits for the other CS

memory.

0x0000

Address Bit Name/Description Default

0x00406 15:13 Unused. —

12:0 CSG_End_Address. Connection store updates will end at this address. To apply the end

address to a single CS memory, disable the bit write enable register bits for the other CS

memory.

0x1FFF

Address Bit Name/Description Default

0x00408 15:0 CSG_Bit_Write_Enable_Low. Controls writing of bits [15:0] in the connection store memory.

0 = Ignore the corresponding bi t (this bit in memory maintains its present value).

1 = Write the corresponding bit.

0xFFFF

Address Bit Name/Description Default

0x0040A 15:0 CSG_Bit_Write_Enable_High. Controls writing of bits [31:16] in the connection stor e memory.

0 = Ignore the corresponding bi t (this bit in memory maintains its present value).

1 = Write the corresponding bit.

0xFFFF

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 41

Table 6-27. CSG_Se ed_Low (Read/Write)

Seed value for the pseudorandom pattern generator for the low word of the connection store RAM.

Table 6-28. CSG_Seed_High (Read/Write)

Seed value for the pseudorandom pattern generator for the high word of the connection store RAM.

Table 6-29. CSG_OR_Mask_Low (Read/Write)

This register allows bits in the connection store to be forced to 1. CS[15:0] = (pseudorandom data [15:0] OR

CSG_OR_Mas k_L o w) AND CSG _AN D_ Ma sk _L ow , bit en ab le d by CSG _W rite _ Ena b le_ Lo w.

Table 6-30. CSG_OR_Mask_High (Read/Write)

This register allows bits in the connection store to be forced to 1. CS[31:16] = (pseudorandom data [31:16] OR

CSG_OR_Mask_High) AND CSG_AND_Mask_High, bit enabled by CSG_Write_Enable_High.

Note: CS[22:18] are always 0.

Address Bit Name/Description Default

0x00410 15:0 CSG_Seed_Low. If the LFSR_Seed_Control bit (see Table 6-21 on page 39) is asserted, at

the beginning of a CSG operation, bits [15:0] of the LFSR supplying the connection store

RAM with data are loaded with this programmable seed.

0xFFFF

Address Bit Name/Description Default

0x00412 15 Unused. —

14:0 CSG_Seed_High. If the LFSR_Seed_Control bit (see Table 6-21) is asserted, at the begin-

ning of a CSG operation, bits [30:16] of the LFSR supplying the connection store RAM with

data ar e loaded with this programmable seed.

0x7FFF

Address Bit Name/Description Default

0x00418 15:0 CSG_OR_Mask_Low. This register allows b it fields in th e connection store to be for ced to a

one during a CSG fill operation. A bit-wise OR of this register and bits [15:0] of the pseudo-

random generated data are performed to obt ain the dat a for connection store. The result a nt

is then ANDed with CSG_AND_Mask_Low.

0x0000

Address Bit Name/Description Default

0x0041A 15:7 CSG_OR_Mask_High_B. This r egister allows bit fields in the con nection store to be forced

to a 1 during a CSG fill operation. A bit-wise OR of this register and bits [31:23] of the pseu-

dorandom generated data are performed to obtain the data for connection store. The result-

ant is then ANDed with CSG_AND_Mask_High.

0x000

6:2 Unused. —

1:0 CSG_OR_Mask_High_A. Th is register allows bit fiel ds in the connection store to be forced

to a 1 during a CSG fill operation. A bit-wise OR of this register and bits [17:16] of the pseu-

dorandom generated data are performed to obtain the data for connection store. The result-

ant is then ANDed with CSG_AND_Mask_High.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

4242 Agere Systems Inc.

Table 6-31. CSG_AND_Mask_Low (Read/W rite)

This register allows bits in the connection store to be forced to 0. This register takes precedence over CSG_OR_Mask_Low.

CS[15:0] = (pseudorandom data [15:0] OR CSG_OR_Mask_Low) AND CSG_AND_Mask_Low, bit enabled by

CSG_Write_Enable_Low.

Table 6-32. CSG_AND_Mask_High (Read/Write)

This register allows bits in the connection store to be forced to 0. This register takes precedence over CSG_OR_Mask_High.

CS[31:16] = (pseudorandom data [31:16] OR CSG_OR_Mask_High) AND CSG_AND_Mask_High, bit enabled by

CSG_Write_Enable_High.

Note: CS[22:18] are always 0.

Table 6-33. CS_Stream_Control ( Read/Write)

If enabled, this register allows the CSG to program the connection sto re to map a n i ncoming stre am to a n ou tg oing stre am.

Address Bit Name/Description Default

0x0041C 15:0 CSG_AND_Mask_Low. This register allows bit fields in the connection store to be forced to

a 0 during a CSG fill operation. A bit-wise AND of this register and bits [15:0] of the result

from the OR of CSG_OR_Mask_Low with the pseudo random generate d data are performed

to obtain the data for connection store.

0xFFFF

Address Bit Name/Description Default

0x0041E 15:7 CSG_AND_Mask_High_B. This register allows bit fields in the connection store to be

forced to a 0 during a CSG fill operation. A bit-wise AND of this register and bits [31:23] of

the result from the OR of CSG_OR_Mask_High with the p se udorand om gene rated da t a are

performed to obtain the data for connection store.

0x1FF

6:2 Unused. —

1:0 CSG_AND_Mask_High_A. This register allows bit fields in the connection store to be

forced to a 0 during a CSG fill operation. A bit-wise AND of this register and bits [17:16] of

the result from the OR of CSG_OR_Mask_Hi gh with p seudor andom gene rated dat a are per-

formed to obtain the data for connection store.

Address Bit Name/Description Default

0x00428 15:13 Unused. —

12:8 CS_Destination_Stream_Select. Specifies destination channel in stream switching

function. All time slots for this specified stream will be sourced from the stream specified in

CS_Source_Stream_Select. The Enable_Stream_Switching control bit (see Table 6-21)

must be set to enable this function.

0x00

7:5 Unused. —

4:0 CS_Source_Stream_Select. Specifies the source stream in the stream switching function.

All time slots for this stream will be sent to the stream specified by

CS_Destination_Stream_Select. The Enable_Stream_Switching control bit (see Table 6-21)

must be set to enable this function.

0x00

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 43

Table 6-34. CSG_Configuration (Read/Write)

This register is used to populate the specified connection store RAM fields when the CSG is in the N-to-N mapping mode.

This register is not used w hen in th e LF SR pa tt er n mo d e (se e CSG _M o de_ S ele ct on Table 6-21 on page 39 bit 1).

Address Bit Name/Description Default

0x0042A 15:11 Reserved. 00000

10 TPM_Enable_Field_Fill. The Test_Pattern_Monitor_Enable field (see Table 8-2 on

page 59) in the connection store RAM is filled with this value. 0

9:8 Mode_Field_Fill. The T ime_Slot_Mode bit s (see Table 8-2) in the connection store are filled

with this pattern.

00 = Low latency.

01 = Frame integrity.

10 = Alternate data.

11 = TGP data.

7High_Impedance_Control_Field_Fill. Fills the Time_Slot_High_Impedance control bit

(see Table 8-2) in the connection store. 0

6:0 Unused. —

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

4444 Agere Systems Inc.

6.7 Test Pattern Generator and Monitor Registers

Table 6-35. TPG_Configuration (Read/Write)

The TPG can be configured to generate any one of the IT U-T test patterns specified in O.150, O.151, or O.152, as well as

idle code or user-specified data .

Address Bit Name/Description Default

0x00600 15:7 Unused. —

6TPG_Pattern_Invert. Data output patterns are inverted when this bit is selected.

0 = Do not invert TPG data.

1 = Invert TPG data.

5Enable_Error_Exercise. This works in conjunction with both the TPG_Inject_Error_Count

(see Table 6-4 0 on page 46) and the Data_Invert_Mask (see Table 6-41). The latter is an 8-

bit register that allows for bit-wise XORing of the data output. The former gets loaded with

the number of N-bit errors that will be generated with N being the number bits set in the

Data_Invert_Mask. If the Data_Invert_Mask is set to 0x00, then no errors will be injected

despite the fact the TPG_Inject_Error_Count register will continue to decrement.

0 = Disable error exercising.

1 = Enable error exercise option.

4Pattern_Generator_Enable. Enable the pattern generator:

0 = Pattern generator off.

1 = Pattern generator on.

Note: Setting this bit to 0 will not reset the TPM_Error_Count (see Table 6-39 on page 46)

nor the Pattern_Error_Detected (see Table 6-42 on page 47). Setting this bit to a 1

will reset the aforementioned.

3:0 TPG_Pattern_Select. These bits select the test pattern to be generated and inse rted into

the selected time slots. Changing the pattern will reset the TPM_Error_Count register (see

Table 6-39 on page 46) and Pattern_Error_Detected (see Table 6-42 on page 47).

0000 = Idle pattern (0011).

0001 = Mark (all ones AIS).

0010 = Alternating 0s and 1s—0x55.

0011 = 29 – 1.

0100 = 211 – 1.

0101 = 211 – 1 with zero suppression when previous 7 bits are zero.

0110 = 211 – 1 with zero suppression when next 7 bits are zero.

0111 = 215 – 1.

1000 = 220 – 1.

1001 = QRSS (220 – 1 with zero suppression when the next 14 bits are zero).

1010 = QRSS (220 – 1 with zero suppression when the next 14 bits are zero).

1011 = 223 – 1.

1100 = 229 – 1.

1101 = 231 – 1.

1110 = Indexed (data increments each time slot).

1111 = User pattern (repeating 2 bytes of data as specified in TPG_User_ P attern).

0x0

Table 6-36. TPG_User_Pattern (Read/Write)

Address Bit Name/Description Default

0x00602 15:0 TPG_User_Pattern. Pa tte rn-ge ne rato r prog ra mmab le u ser wor d. If pattern 0xF is specified

by the TPG_Pattern_Select field, this data will be sent out as TPG data. Bit [15] gets trans-

mitted first in time.

0x0000

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 45

Table 6-37. TPM_Configuration (Read/Write)

The TPG can be configured to monitor any one of the ITU-T test patterns specified in O.150, O.151, or O.152, as well as

idle code or user-specified data .

Address Bit Name/Description Default

0x00604 15:7 Unused. —

6TPM_Pattern_Invert. Incoming data patterns are inverte d prior to checking when this bit is

selected.

0 = Do not invert TPM data.

1 = Invert TPM data.

5Reset_TPM_Error_Counter. Res ets the error co un te r (T PM _Er ro r_ Co u nt see Table 6-39

on page 46).

0 = Allow TPM_Error_Count to advance.

1 = Reset TPM_Error_Count (to zero).

4Pattern_Monitor_Enable. Enable the pattern monitor:

0 = Pattern monitor off.

1 = Pattern monitor on.

3:0 TPM_Pattern_Select. These bits select the test pattern to be monitored from the selected

time slots.

0000 = Idle pattern (0011).

0001 = Mark (all ones AIS).

0010 = Alternating 0s and 1s—0x55.

0011 = 29 – 1.

0100 = 211 – 1.

0101 = 211 – 1 with zero suppression when previous 7 bits are zero.

0110 = 211 – 1 with zero suppression when next 7 bits are zero.

0111 = 215 – 1.

1000 = 220 – 1.

1001 = QRSS (220 – 1 with zero suppression when the next 14 bits are zero).

1010 = QRSS (220 – 1 with zero suppression when the next 14 bits are zero).

1011 = 223 – 1.

1100 = 229 – 1.

1101 = 231 – 1.

1110 = Indexed (data increments each time slot).

1111 = User pattern (repeating 2 bytes of data as specified in TPG_User_ P attern).

0x0

Table 6-38. TPM_User_Pattern (Read/Write)

Address Bit Name/Description Default

0x00606 15:0 TPM_User_Pattern. User-definable data for pattern monitoring. If pattern 0xF is specified

by the TPM_Pattern_Select field, thi s data will be used to check against incoming data. Bit

[15] gets checked first in time.

0x0000

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

4646 Agere Systems Inc.

* See Table 6-15 on page 37 bit 2.

This register provides a mask fo r specifying which bits of TPG data are to be inverted when forcing errors.

Table 6-39. TPM_Error_Count (Sat/Roll*)

Address Bit Name/Description Default

0x00608 15:0 TPM_Error_Count. This status register accumulates the number of pattern bit errors

detected in the monitored time slot(s).

If Saturate_Rollover_Select (see Table 6-15 on page 37) is set to a 1, this register will sat-

urate at 0xFFFF and not be allowed to roll over.

If Saturate_Rollover_Select is set to a 0, the counter will roll over (count to 0x0 on the next

error after 0XFFFF), the Pattern_Error_Detected status bit (see Table 6-42 on page 47)

will not be reset.

The TPM_Error_Count register can be reset in one of the following four ways:

1. The pattern is changed.

2. The bit RESET_TPM_Error_Counter (in the TPM_Configuration register, see Table 6-37

on page 45) is asserted.

3. This register is written. The TPM_Error_Count register will be set to 0x0000 independent

of the value written.

4. This register is read when Register_Clearing_Mode = 1 (see Table 6-15 on page 37).

Note: Since TPM_Error _Count is the source of Pattern_Error_Detected status bit (see

Table 6-4 2 on page 47 ), then the clearing of this register will also clear the error bit.

0x0000

Table 6-40. TPG_Inject_Error_Cou nt (Write Only)

Address Bit Name/Description Default

0x0060A 15:0 TPG_Inject_Error_Count. This register specifies the number of errors to be injected. The

actual number of bit errors that will be injected will equal to the TPG_Inject_Error_Count x

N, where N is the number of bits set to 1 in the TPG_Data_Invert_Mask. The readback of

this register will always reflect the remaining error count and not the original number written

to this register.

0x0000

Table 6-41. TPG_Data_Invert_Mask (Read/Write)

Address Bit Name/Description Default

0x0060C 15:8 Unused. —

7:0 Data_Invert_Mask. The contents of this register are XORed with the TPG output word pro-

viding bit-wise error control.

Note: If Data_Invert_Mask = 0x00, then no errors will be injected.

0x00

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 47

Table 6-43. TPM_Status_Mask (Read/Write)

Mask bits for the TPM_Status register.

Table 6-42. TPM_Status (Read Only)

Address Bit Name/Description Default

0x0060E 15:2 Unused. —

1Test_Pattern_Lock. This status bit indicates if the monitor has achieved a pattern lock on

all selected time slots.

0 = Monitor is locked on the pattern.

1 = Monitor is searching for the pattern.

—

0Pattern_Error_Detected. This status bit indi cates if the TPM_Error_ Count register (see

Table 6-39 on page 46) is nonzero.

0 = No errors detected.

1 = Nonzero (one or more errors detected).

Note: This bit is cleared by clearing TPM_Error_Count. Refer to function description of

TPM_Error_Count.

—

Address Bit Name/Description Default

0x00610 15:2 Unused. —

1Test_Pattern_Lock_Mask. This bit masks the Test_Pattern_Lock bit (see Table 6-42) from

causing an interr up t.

0 = Nonmasked. If the monitor is not locked, an interrupt will be generated.

1 = Masked. An error will not cause an interrupt.

0Pattern_Error_Mask. This bit masks the Pattern_Error_Detected bit (see Table 6-42) from

causing an interr up t.

0 = Nonmasked. An error will cause an interrupt.

1 = Masked. An error will not cause an interrupt.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

4848 Agere Systems Inc.

6.8 Concentration Highway Configuration Registers

Table 6-44. Receive_CHI_Configuration (Read/Write)

Each of the incoming CHIs can be independently designed and programmed with a unique offset from the master frame

synchronization. This bank of registers works in conjunction with the corresponding Receive_CHI_Time_Slot_Offset regis-

ters (see Table 6-52 on page 53) to provide this control. These registers provide the bit and fractional bit offset control.

Address Bit Name/Description Default

0x00A00—0x00A3E 15 Receive_CHI_Loopback_Enable.

0 = Input data for this receive CHI comes from the corresponding RXD pin.

1 = Input dat a for this receive CHI comes from th e corresponding tr ansmit CHI (see

CHI_Feedback_Source_Selection in Table 6-48 on page 50 bit 15).

14:10 Unused. —

9:8 Receive_CHI_Bit_Rate. These bits indicate the data rate of this receive CHI.

00 = 2 Mbits/s.

01 = 4 Mbits/s.

10 = 8 Mbits/s.

11 = 16 Mbits/s. (Only valid with 16 MHz CHICLK clock.)

7Unused. —

6:4 Receive_CHI_Bit_Offset. These bit s represent the bit offset relative to the frame

synchronization sample point for this receive CHI (in binary, 0—7 bits). 000

3:2 Unused. —

1Receive_CHI_Half_Bit_Offset.

0 = No additional offset.

1 = Indicates an additional 1/2 bit of offset for this receive CHI.

0Receive_CHI_Quarter_Bit_Offset.

0 = No additional offset.

1 = Indicates an additional 1/4 bit of offset for this receive CHI.

Table 6-45. Receive_CHI_Status (CORWN) Receive_CHI_Status (CORWN)

Address Bit Name/Description Default

0x00A80 15:3 Unused. —

2Receive_Clock_Error.

0 = No clock error detected.

1 = Indicates a slow (or missing) CHICLK.

—

1Receive_Lock_Error.

0 = No clock error detected.

1 = Indicates a synchronization error has occurred between the CHICLK and th e internal

PLL clock. If Enable_Receive_CHI_Automatic_Resynchronization (see Table 6-47 on

page 49) is not a 1, then a manual resynchronization should be performed

(Force_Receive_CHI_Resynchronization, see Table 6-47).

—

0Receive_Frame_Sync_Error.

0 = No frame synchronization error detected.

1 = Indicates a frame synchronization error has occurred. This means the CHI frame

synchronization was either missing or misplaced. For missing frame synchronizations,

this status is the only action taken. For misplaced frame synch ronizations, the device

automatically sy nc hr on ize s to the new fra m e syn ch ro niz at i on posi tio n.

—

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 49

Table 6-46. Receive_CHI_Status_Mask (Read/Write)

Mask bits for the Receive_CHI_Status register (see Table 6-45).

Table 6-47. Receive_CHI_Global_Configuration (Read/Write)

Global configuration control for all the receive CHIs.

Address Bit Name/Description Default

0x00A82 15:3 Unused. —

2Receive_Clock_Error_Mask.

0 = The Receive_Clock_Error bit (see Table 6-45) will cause an interrupt if active (unless

masked at a higher level).

1 = The Receive_Clock_Err or bit is blocked from causing an interrupt.

1Receive_Lock_Error_Mask.

0 = The Receive_Lock_Error bit (see Table 6-45) will cause an interrupt if active (unless

masked at a higher level).

1 = The Receive_Lock_Error bit is blocked from causing an interrupt.

0Receive_Frame_Sync_Error_Mask.

0 = The Receive_Frame_Sync_Error bit (see Table 6-45) will cause an interrupt if active

(unless masked at a higher level).

1 = The Receive_Frame_Sync_Error bit is blocked from causing an interrupt.

Address Bit Name/Description Default

0x00A84 15:4 Unused. —

3Force_Receive_CHI_Resynchronization.

0 = Normal operation.

1 = This forces the receive CHI/PLL interface to resynchronize.

2Enable_Receive_CHI_Automatic_Resynchronization.

0 = The device will inhibit automatic resynchronization of the receive CHI/PLL interface if it

detects it is out-of-synchronization (not recommended).

1 = The device will automatically resynchronize the receive CHI/PLL interface if it detects it

is out-of-synchronization.

1Receive_Frame_Sync_Polarity. This bit indi cates the polarity of th e frame synchronization

signal.

0 = Indicates the frame synchronization is active-low. The reference point for all receive CHI

timing is the first active edge of CHICLK (see Receive_Clock_Edge) after the frame

synchronization transitions to the active level as defined here.

1 = Indicates the fram e syn ch ro niz at ion is active -h ig h.

0Receive_Clock_Edge. This bit indicates which ed ge of the CHICLK to use to sample the

frame synchronization signal.

0 = Indicates sampling on the falling edge. This also defines the reference point for all

receive CHI timing and offsets.

1 = Indicates sampling on the rising edge of the clock.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

5050 Agere Systems Inc.

Table 6-48. Transmit_CHI_Configur ation (Read/Write)

Each of the incoming CHIs can be independently designed and programmed with a unique offset from the master frame

synchronization. This bank of registers works in conjunction with the corresponding Transm it_CHI_T ime_Slo t_Offse t regis-

ters (see Table 6-53 on page 53) to provide this control. These registers provide the bit and fractional bit offset control.

Figure 6-1. Transmit CHI Configuration (R/W)

Address Bit Name/Description Default

0x00C00—0x00C3E 15 CHI_Feedback_Source_Selection. Selects which data is sent to corresponding

receive CHI.

0 = Means pre-output data is sent.

1 = Means the input from the bidirectional TXD pin is sent. This bit has no effect

unless the corresponding receive CHI's Receive_CHI_ Loopback_Ena ble bit is

one (see Table 6-44 on page 48).

14 Unused. —

13:12 Driver_Enable_Control. These two bits determine how the output TXD pin is

actually driven.

00 = Always disabled.

01 = Based on time-slot programming (timing from CHICLK).

10 = Reserved.

11 = Similar to 01 except all time slots are disabled near end of time slot (see

Transmit_High_Impedance_Delay in Table 6-51 on page 52 bits [6:4]).

11:10 Unused. —

9:8 Transmit_CHI_Bit_Rate. These bits indicate the data rate of this transmit CHI.

00 = 2 Mbits/s.

01 = 4 Mbits/s.

10 = 8 Mbits/s.

11 = 16 Mbits/s (only valid with 16 MHz CHICLK).

7Unused. —

6:4 Transmit_CHI_Bit_Offset. These bits represent the bit o f fset relative to the frame

synchronization sample point for this transmit CHI (in binary, 0—7 bits). 000

3:2 Unused. —

1Transmit_CHI_Half_Bit_Offset.

0 = No additional delay.

1 = Indicates an additional 1/2 bit of offset for this transmit CHI.

0Transmit_CHI_Quarter_Bit_Offset.

0 = No additional delay.

1 = Indicates an additional 1/4 bit of offset for this transmit CHI. This bit must be 0

when the CHI rate is 16 Mbit s/s or when the CHI rate is 8 Mbits/s mode and the

CHICLK is 8.192 MHz.

SWITCH FABRIC

TXD

RXD

RECEIVE_CHI_LOOPBACK_ENABLE

CHI_FEEDBACK_SOURCE_SELECTION

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 51

Table 6-49. Transmit_CHI_Status (CORWN)

Table 6-50. Transmit_CHI_Status_Mask (Read/Write)

Mask register for the Transmit_CHI_Status register.

Address Bit Name/Description Default

0x00C80 15:2 Unused. —

1Transmit_Lock_Error.

0 = No error detected.

1 = Indicates a synchronization error has occurred between the CHICLK and th e internal

PLL clock. If Enable_Transmit_CHI_Autom a tic_Resynchronization is not a 1 (see

Table 6-51 on page 52), then a manual resynchronization should be performed

(Force_Transmit_CHI_Resynchronization, see Table 6-51).

—

0Transmit_Frame_Sync_Error.

0 = No error detected.

1 = Indicates a frame synchronization er ror has occurred in the transmit CHI section of the

device. This m eans the CHI fram e synchronization was either m issing or misplaced . For

missing frame synchronizations, this st atus is the only action taken. For misplaced frame

synchronizations, the device automatically synchronizes to the new frame synchroniza-

tion position.

—

Address Bit Name/Description Default

0x00C82 15:2 Unused. —

1Transmit_Lock_Error_Mask.

0 = The Transmit_Lock_Error bit (see Table 6-49) will cause an interrupt if active (unless

masked at a higher level).

1 = The Transmit_Lock_Error bit is blocked from causing an interrupt.

0Transmit_Frame_Sync_Error_Mask.

0 = The Transmit_Frame_Sync_Error bit (see Table 6-49) will cause an interrupt if active

(unless masked at a higher level).

1 = The Transmit_Fram e _Sy nc _Er ro r bit is blo cke d fr om caus ing an inte rr up t.

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

5252 Agere Systems Inc.

Table 6-51. Transmit_CHI_Global_Configuration (Read/Write)

Address Bit Name/Description Defaul

0x00C84 15:8 Unused. —

7Global_Transmit_CHI_Output_Enable. This bit is a global control over the 3-state enables of

the transmit CHIs.

0 = All CHIs transmit pins are forced into the high-impedance state.

1 = 3-state control of individual CHIs is placed un der control of the CHI

Transmit_ CHI_Configuration register (see Table 6-48 on page 50).

6:4 Transmit_High_Impedance_Delay. These bits are used in conjunction with Driver_Enable_Control

(see Table 6-48 bits [13:12]) bits. When the Driver_Enable_Control bits = 11, then the

Transmit_High_Impedance_Delay bits determine how early the device will 3-state the output driver at

the end of a time slot. These numbers are approximate because of the sampling error between the

CHICLK and the internal clock. The numbers are actually how much time after the previous clock

edge the output 3-states. For bit settings [6:4]:

000 = Approximately 55 ns after the previous same edge with a 16.384 MHz CHICLK.

= Approximately 55 ns after the previous opposite edge with an 8.192 MHz CHICLK.

001 = Approximately 49 ns after the previous same edge with a 16.384 MHz CHICLK.

= Approximately 49 ns after the previous opposite edge with an 8.192 MHz CHICLK.

010 = Approximately 43 ns after the previous same edge with a 16.384 MHz CHICLK.

= Approximately 43 ns after the previous opposite edge with an 8.192 MHz CHICLK.

011 = Approximately 37 ns after the previous same edge with a 16.384 MHz CHICLK.

= Approximately 37 ns after the previous opposite edge with an 8.192 MHz CHICLK.

100 = Approximately 116 ns after the previous same edge (8.192 MHz CHICLK only).

101 = Approximately 110 ns after the previous same edge (8.192 MHz CHICLK only).

110 = Approximately 104 ns after the previous same edge (8.192 MHz CHICLK only).

111 = Approximately 98 ns after the previous same edge (8.192 MHz CHICLK only).

See Figure 5-15 on page 27 and Table 5-5 on page 27.

000

3Force_Transmit_CHI_Resynchronization.

0 = Normal operation.

1 = This forces the transmit CHI/PLL interface to resynchronize.

2Enable_Transmit_CHI_Automatic_Resynchronization.

0 = The device will inhibit automatic resynchronization of the transmit CHI/PLL interface if it

detects it is out-of-synchr onization (not recommended).

1 = The device will automatically resynchronize the CHI/PLL interface if it detects it is out-of-syn-

chronization.

1Transmit_Frame_Sync_Polarity. This bit indicates the polarity of the frame synchronization sig-

nal.

0 = Indicates the frame synchronization is active-low. Generally, this should be progr ammed with

the same value as Receive_Frame_Sync_Polarity (see Table 6-47 on page 49). The refer-

ence point for all receive CHI timing is the first active edge of CHICLK (see

T ransmit_Clock_Edge below) after the frame synchronization transitions to the active level as

defined here.

1 = Indicates the frame synchronization is active-high.

0Transmit_Clock_Edge. This bit indicates which edge of the CHICLK to use to sample the frame

synchronization signal.

0 = Indicates sampling on the falling edge. Generally, this should be programmed with the same

value as Receive_Clock_Edge (see Table 6-47 on page 49). This also defines the reference

point for all transmit CHI timin g and offsets.

1 = Indicates sampling on the rising edge of the clock.

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 53

Table 6-52. Receive_CHI_Time_Slot_Offset (Read/Write)

Each of the incoming CHIs can be independently designed and programmed with a unique offset from the master frame

synchronization. This bank of registers works in conjunction with the corre sponding Receive_CHI_Configuration registers

(see Table 6-44 on page 48) to provide this control. These registers provide the time-slot offset. The

Receive_CHI_Configuration registers provide the bit and fractional bit offset control.

Table 6-53. Transmit_CHI_Time_Slot_Offset (Read/Write)

Each of the outgoing CHIs can b e independently designed and pr ogrammed with a unique offset from the maste r frame syn-

chronization. This bank of registers works in conjunction with th e corresponding Transmit_CHI_Configuration reg isters (see

Table 6-48 on page 50) to provide this control. These registers provide the time-slot offset. The Transmit_CHI_Configuration

registers provide the bit and fractional bit offset control.

Address Bit Name/Description Default

0x01000—0x0103E 15:8 Unused. —

7:0 Receive_CHI_Offset. Time-slot offset for the receive CHIs. This value should be

programmed as follows (RTO = the number of receive time slots to be offset): —

CHI Rate Offset RC_TS_OFF Value

16 Mbits/s RTO (0—255) RTO

8 Mbits/s RTO (0—127) ((RTO x 2) + 2) modulo 256

4 Mbits/s RTO (0— 63) ((RTO x 4) + 6) modulo 256

2 Mbits/s RTO (0— 31) ((RTO x 8) + 14) modulo 256

Address Bit Name/Description Default

0x01080—0x010BE 15:8 Unused. —

7:0 Transmit_CHI_Offset. Time-slot offset for the transmit CHIs. This value should

be programmed as follows (TTO = the number of transmit time slots to be of fset) : —

CHI Rate Offset TC_TS_OFF Value

16 Mbits/s TTO ( 0—255) TTO

8 Mbits/s TTO (0—127) TTO x 2

4 Mbits/s TTO (0—63) TTO x 4

2 Mbits/s TTO (0—31) TTO x 8

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

5454 Agere Systems Inc.

7 Switch Fabric Control

Table 7-1. SF_S tatus (CORWN)

Table 7-2. SF_Status_Mask (Read/Write)

Provides a mask for all bits in the SF_Status register (see Table 7-1). These bits are output masks of the register. That is,

setting the mask will not stop the error bit from being set, but will block an interrupt from being propagated if the correspond-

ing error is set.

Address Bit Name/Description Default

0x01124 15:3 Unused. —

2Receive_Link_Synchronization_Error.

0 = No error detected.

1 = Missing or misplaced synchronization on interface between the receive CHI and the

switch fabric (clear-on-read/clear-on-write).

—

1Transmit_Sync_Error.

0 = No error detected.

1 = Missing or misplaced synchronization on interface between the transmit CHI and the

switch fabric (clear-on-read/clear-on-write).

—

0Connection_Store_Parity_Error.

0 = No error detected.

1 = Connection store parity error detected (read only, clear by clearing

Connection_S tore _Parity_Error_Address_T rap, see Table 7-5 on pag e 56). The location

with the pa rity error can be found in Connection_Store_Parity_Error_Address_Trap.

—

Address Bit Name/Description Default

0x01126 15:3 Unused. —

2Receive_Link_Synchronization_Error_Mask.

0 = Unmasked, Receive_Link_Synchronization_Error will (see Table 7-1) cause interrupt

(unless masked at higher level).

1 = Masked, Receive_Link_Synchronization_Error will not cause an interrupt.

1Transmit_Sync_Error_Mask.

0 = Unmasked, Transmit_Syn c_Error (s ee Table 7-1 ) will cause inte rrupt (u nless masked at

higher level).

1 = Masked, Transmit_Sync_Error will not cause an interrupt.

0Connection_Store_Parity_Error_Mask.

0 = Unmasked, Connection_Store_Parity_Error (see Table 7-1) will cause interrupt (unless

masked at higher level).

1 = Masked, Connection_Store_Parity_Error will not cause an interrupt.

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 55

Table 7-3. Data_Store_Time_Slot_Capture_Select (Read/Wr ite)

For diagnostic and other purposes, a single incoming time slot can be sampled and mad e availab le to be rea d from the mi-

croprocessor interface. This register specifies which time slot will be sampled.

Table 7-4. Data_S tore_Captured_Data (Read Only)

This register contains data sampled in two consecutive frames from the time slot specified in

Data_Store_Time_Slot_Capture, see Table 7-3. This register is continually updated every frame (alternating high/low byte

each frame).

Address Bit Name/Description Default

0x01142 15:13 Unused. —

12:0 Data_Store_Time_Slot_Capture. Specifies which time slot should be captured (sampled)

(0—8,191). This value is a fu nction of the stream (CHI) number, the data rate of the CHI, the

time-slot offset of the CHI (RTO), and the desired time slot (TS) of the CHI. The following

algorithms ca n be use d to determ in e th e va lue for th is field :

For a 16 Mbits/s CHI:

—(32 x [(TS + RTO) mod 256]) + CHI, where TS and RTO range from 0—255 .

For an 8 Mbits/s CHI:

—(32 x [([2 x (TS + RTO)] + 2) mod 256]) + CHI, where TS and RTO range from 0—127.

For a 4 Mbits/s CHI:

—(32 x [([4 x (TS + RTO)] + 6) mod 256]) + CHI, where TS and RTO range from 0—63.

For a 2 Mbits/s CHI:

—(32 x [([8 x (TS + RTO)] + 14) mod 256]) + CHI, where TS and RTO range from 0—31.

0x0000

Address Bit Name/Description Default

0x01144 15:8 Captured_Data_1. Data captured from the time slot specified by

Data_Store_Time_Slot_Capture (see Table 7-3). This field is updated every other frame

alternating with Captured_Dat a_0. Dependin g on when this is read by the microproce ssor , it

may be either from the frame before or after that sampled in Captured_Data_0.

—

7:0 Captured_Data_0. Data captured from the time slot specified by

Data_Store_Time_Slot_Capture (see Table 7-3). This field is updated every other frame

alternating with Captured_Dat a_1. Dependin g on when this is read by the microproce ssor , it

may be either from the frame before or after that sampled in Captured_Data_1.

—

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

5656 Agere Systems Inc.

Table 7-5. Connection_Store_Parity_Error_Address_Trap (CORWN)

As the connection store is continually read, its parity is checked. If an error is detected, the location with the error is saved

in this register and the Conn ection_Store_Par ity_Error (see Table 7-1 on page 54) error bit is set. If in clear-on-read (COR)

mode, when this register is read, the Connection_Store_Parity_Error bit is cleared. If in clear-on-write (COW) mode, any

write to this register clears Connection_Store_Parity_Error.

Table 7-6. Receive_Link_Offset (Read Only)

This register displays the offset of the receive link with respect to the switch fabric. See also Transmit_Link_Offset and

Force_Transmit_Link_Offset in Table 7-7.

Table 7-7. Transmit_Link_Offset (Read/Write)

This register displays/controls the offset of the transmit links with respect to the switch fabric. Normally, the

Transmit_Link_Offset is determined by the CHI frame synchronization's relative position to the switch fabric synchronization.

In this case, bit [15] of this register should be set to 0.

Address Bit Name/Description Default

0x01146 15 Unused. —

14:0 Connection_Store_Parity_Error_Address. This bit field contains the address within the

connection store with a parity error. The address of the first error (after a clear) is sampled

and saved.

—

Address Bit Name/Description Default

0x01148 15:12 Unused. —

11:0 Link_Offset. This field contains the time-slot offset of the receive link. —

Address Bit Name/Description Default

0x0114C 15 Force_Transmit_Link_Offset.

0 = Allows the switch fabric to self-determine its offsets.

1 = Forces the device to use the Transmit_Offset value to align the switch fabric to a deter-

ministic position relative to the CHI frame synchronization. If this is set to 1, this register

value should be set and the system allowed to stabilize (more than 250 µs) prior to read-

ing the value in Receive_ L i nk _O ffset (see Table 7-6).

—

14:12 Unused. —

11:0 Transmit_Offset. If Force_Transmit_Link_Offset is set to 1, this value will force the switch

fabric to align itself this many time slots off from the CHI frame synchronization. Please con-

tact your FAE if you plan on using th is fea ture .

—

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 57

Table 7-8. Wide_Mode_Control (Read/Write)

For applications that require switching of time slots of greater than 8 bits, parallel devices must be used. These bits can be

used to facilitate such operation. Please contact your FAE if setting these bits to other than the default value of 0.

Address Bit Name/Description Default

0x0114E 15:3 Unused. —

2:0 Wide_Mode_Operation.

000 = Disable multifabric synchronization (i.e., normal mode) (de fa ult).

001 = Software algorithm mode, maximum allowable receive delay of approximately 7 µs.

010 = Software algorithm mode, maximum allowable receive delay of approximately 15 µs.

011 = Software algorithm mode, maximum allowable receive delay of approximately 31 µs.

100 = Disable multifabric synchronization (i.e., normal mode) .

101 = Minimal latency mode, maximu m allowable receive delay of approximately 7 µs.

110 = Minimal latency mode, maximum allowable receive delay of approximately 15 µs.

111 = Minimal latency mode, maximum allowable receive delay of approximately 31 µs.

Note: For the last three modes, the minimum, average, and maximum delay in low-latency

(LL) mode will be up to 7 µs, 15 µs, and 31 µs larger than regular LL mode. For the

software modes, the minimum delay in LL mode will be up to 7 µs, 15 µs, and 31 µs

larger, and the maximum delay will be up to 132 µs, 140 µs, and 156 µs larger than

regular mode.

000

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

5858 Agere Systems Inc.

8 Connection Store

The connection store RAM contains the per-time-slot control information for outgoing time slots. Each location in the RAM

corresponds to one outgoing time slot and contains all the time-slot specific control information for that time slot. The specific

address offset into the RAM is calculated as follows:

ADDR[15] = 0.

ADDR[14:7] destination (outgoing) time-slot number of stream identified by address bits [6:2].

ADDR[6:2] destination (outgoing) stream (CHI) number.

ADDR[01] 0 = Low_Control, 1 = High_Control.

ADDR[00] = 0 (no byte addressability).

Address bits [14:7] are dependent on the destination (outgoing) CHI rate and should be calculated as follows, where TS is

the outgoing CHI time-slot number:

Table 8-1. Low_Control_Word (Read/Write)

The low-control word in the connection store h as two functio ns. Normally, it is used to pr ogram the addr ess of the incoming

time slot to which the outg oing time slot is connected. The outgoing time slot is implied by the connection store add ress as

described above. This normal switch operation will apply if the time-slot mode bits in the high-control word are set to low

latency or frame integrity switching modes. If alternate data mode is selected, the low control word contains the alternate

data (see Table 8-2, bit [9:8]).

* Bits [15:0] have dual meaning based on the value in the Time_Slot_Mode field of the High_Control_Word (see Table 8-2).

If the Time_Slot_Mode field is set to 10 (alternate data), then bits [15:0] have the following meaning:

Bits [7:0] are set to Alternate_Data_Pattern_1.

Bits [15:8] are set to Alternate_Data_Pattern_2.

If the Time_Slot_Mode field is set to anything other than 10, then bits [15:0] have the following meaning:

Bits [4:0] are set to Stream_Pointer.

Bits [12:5] are set to Time_Slot_Pointer.

Bits [15:13] are reserved.

Rate A[14:7]

16 MHz TS (0—255)

8 MHz TS x 2 (TS = 0—127)

4 MHz TS x 4 (TS = 0—63)

2 MHz TS x 8 (TS = 0—31)

Address Bit*Name/Description Default

0x10000—

0x17FFC 15:8 Alternate_Data_Pattern_2. If alternate data is selected by the mode bits in the corre-

sponding high control location, the data in this byte will alternate with the

Alternate_Data_Pattern_1 pattern and be sent out on the transmit time slot.

—

12:5 Time_Slot_Pointer. This field selects the desired time slot from the source stream (CHI).

This value is dependent on the speed (dat a rate) of the receive CHI specified by

Stream_Pointer and should be programmed as follows, where TS is the desired time-slot

number:

—

Receive CHI Rate Time_Slot_Pointer [7:0]

16 Mbits/s TS (0—255)

8 Mbits/s TS x 2 (TS = 0—127)

4 Mbits/s TS x 4 (TS = 0—63)

2 Mbits/s TS x 8 (TS = 0—31)

7:0 Alternate_Data_Pattern_1. If alternate data is selected by the mode bits in the corre-

sponding high control location, the data in this byte will alternate with the

Alternate_Data_Pattern_2 pattern and be sent out on the transmit time slot.

—

4:0 Stream_Pointer. This field selects one of 32 incoming streams. —

Data Sheet, Revision 3 TSI-4

September 21, 2005 4k x 4k Time-Slot Interchanger

Agere Systems Inc . 59

Table 8-2. High_Control_Word (Read/Write)

Address Bit Name/Description Default

0x10002—0x17FFE 15:11 Reserved. 0x0

10 Test_Pattern_Monitor_Enable.

0 = The TPM is disable for this time slot.

1 = This bit causes dat a for this time slot to be se nt to the test p atter n mon itor for

checking.

—

9:8 Time_Slot_Mode. This field defines in which of th e following modes the time slot

will operate:

00 = Low latency.

01 = Frame integrity.

10 = Alternate dat a.

11 = TPG data.

—

7Reserved.

Note: This bit must be set to zero.

—

6:5 Unused. —

4General_Purpose_Bit. This is a general-purpose read/write bit. It causes no

action within the device. —

3:0 Unused. —

TSI-4 Data Sheet, Revision 3

4k x 4k Time-Slot Interchanger September 21, 2005

6060 Agere Systems Inc.

9 Outline Diagrams

Note: Dimensions are in millimeters.

0.20

BOTTOM VIEW

1.75 TYP.

1.20 x 45° APPROX

A1 INDICATOR

(PLATED)

0.80 ± 0.050

0.56 ± 0.0 6

30°

0.50 ± 0.10

0.35 Z

1618

1.00

17.70

SEATING PLANE

0.50 R MAX

SQUARE

19.00

SQUARE

APPROX

ALL SIDES

0.10 Z

ALL EDGES

1.86 ± 0.21

TYP 3 PLACES

4.00 x 45° APPROX

TYP 4 CORNERS

USE OF EJECTOR

PINS IS OPTIONAL

TYP

0.63 DIA

A1 INDICATOR

(UNDER SOLDER MASK)

TOP VIEW

CENTER ARRAY

FOR THERMAL

ENHANCEMENT

0.50

+0.70

–0.05

+0.07

–0.13

Copyright © 2005 Agere Systems Inc .
All Rights Reserved
September 21, 2005
DS05-117STSI-3 (Replaces DS05-117STSI-2)
Data Sheet, Revision 3 TSI-4
September 21, 2005 4k x 4k Time-Slot Interchanger
Agere Systems Inc. reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. 
Agere, Agere Systems, and the Agere logo are registered trademarks of Agere Systems Inc. 
For additional information, contact your A gere Systems Account Manager or the following:
INTERNET: Home: http://www.agere.com  Sales: http://www.agere.com/sales
E-MAIL: docmaster@agere.com
N. AMERICA: Agere Systems Inc., Lehigh Valley Central Campus, Room 10A-301C, 1110  Ame rican P arkway NE, Allentown, PA 18 109-9 138
1-800-372-2447, FAX 610-712-4106 (In CANADA: 1-800-553-2448, FAX 610-712-4106)
ASIA: CHINA: (86) 21-54614688 (Shanghai), (86) 755-25881122 (Shenzhen), (86) 10-65391096 (Beijing)
JAPAN: (81) 3-5421-1600 (Tokyo), KOREA :  (82) 2-767-1850 (Seoul), SINGAPORE: (65) 6741-9855, TAIWAN: (886) 2-2725-5858 (Taipei)
EUROPE: Tel. (44) 1344 296 400
10 Ordering Information
11 Change History
On pages 1, 15, and 61 changed the device name. On page 61 changed the part numbers.
On page 20 deleted 2 sentences at the beginning  of the page. (All timing par ameter s are refer enced to V IHmin a nd VILmax. 
The reference signal polarity may be inverted for some timing parameters.) 
On page 20 updated Figure 5-3, ac Timing Specification.
On page 20 updated Table 5-3. CMOS Output ac Timing Specification * .
On page 21 under Tabl e 5-4 eliminated the following sentence: All timing specifications are with respect to VIHmin and VIL-
max as shown in Figure 5-3. Also, clarifie d the footnote.
On page 27 deleted footnote † under Table 5-5 and clarified the remaining footnote.
On page 28 deleted the footnote under Table 5-6.
On page 29 deleted the footnote under Table 5-7.
11.1 Navigating Through an Adobe Acrobat Document
If the reader displays this document in Acrobat Read er, clicking on any blue entry in the text will bring the reader to that ref-
erence point. 
Adobe Acrobat and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
Table 10-1. Ordering Information
Device Part Number Ball Count Package Comcode
TSI-4 TTSI004321BL-2-DB 240 PBGAM1 700081542
L-TTSI004321BL-2-DB 700081543*
* Pb-free/RoHS.