TS3006 Demo Board A 1.55V to 5.25V, 1.9A, 9kHz to 300kHz Silicon Timer FEATURES DESCRIPTION The TS3006 is a single-supply, second-generation oscillator/timer that is fully specified to operate at a supply voltage range of 1.55V to 5.25V while consuming less than 2.4A(max) supply current. Requiring only a resistor to set the base output frequency (or output period) at 25kHz (or 40s) with a 50% duty cycle, the TS3006 timer/oscillator is compact, easy-to-use, and versatile. Optimized for ultra-long life, low-frequency, battery-powered/portable applications, TS3006 joins the TS3001, TS3002, TS3004, and TS3005 in the CMOS timer family of the "NanoWatt AnalogTM" series of high-performance analog integrated circuits. 5V Supply Voltage FOUT Output Period: 40s(25kHz) o RSET = 4.32M Fully Assembled and Tested 2in x 2in 2-layer circuit board COMPONENT LIST DESIGNATION QTY C2 1 R1 U1 VDD,F_OUT 1 1 2 DESCRIPTION 4.7F 10% capacitor (0805) 4.32M 1% (0805) TS3006 Test points The TS3006 requires only an RSET = 4.32M resistor to set the FOUT output period to 40s(25kHz). The complete circuit is designed at a supply voltage of 5V. The TS3006 is fully specified over the -40C to +85C temperature range and is available in a low-profile, 8-pin 3x3mm TDFN package with an exposed back-side paddle. Product data sheet and additional documentation can be found at www.silabs.com. ORDERING INFORMATION Order Number Figure 1. TS3006 Demo Board Circuit Figure 2. TS3006 Demo Board (Top View) TS3006DB Description TS3006 Demo Board Figure 3. TS3006 Demo Board (Bottom View) Page 1 (c) 2014 Silicon Laboratories, Inc. All rights reserved. TS3006 Demo Board DESCRIPTION The TS3006 requires only an RSET = 4.32M resistor to set the FOUT/PWMOUT output period to 40s(25kHz). The complete circuit is designed at a supply voltage of 5V and it is shown in Figure 1. The TS3006 is a user-programmable oscillator where the period of the square wave at its FOUT terminal is generated by an external resistor connected to the RSET pin. The output period is given by: FOUT (Hz) 1.08E11 RSET Equation 1. FOUT Frequency Calculation With RSET = 4.32M, the FOUT period is approximately 40s (25kHz) with a 50% duty cycle. As design aids, Tables 1 lists TS3006's typical FOUT frequency for various standard values for RSET. RSET (M) 2) Connect the DC power supply positive terminal to the test point labeled VDD. Connect the negative labeled GND. 3) To monitor the FOUT output signal, connect the signal terminal of an oscilloscope probe to the test point labeled FOUT and the ground terminal to the test point labeled GND. 4) Select a channel on the oscilloscope and set the vertical voltage scale and the vertical position to 2V/DIV and 0V, respectively. Set the horizontal time scale to 5s/DIV. The coupling should be DC coupling. Turn on the power supply. The supply current will vary depending on the load on the output. Given the default set-up on the board, the FOUT output period is approximately 40s. With an output load of 15pF on FOUT due to the oscilloscope probe, the supply current should be less than 4A. FOUT (kHz) 0.360 300 1 108 2.49 43.37 4.32 25 6.81 15.86 9.76 11.07 12 9 Table 1: FOUT vs RSET QUICK START PROCEDURE Required Equipment TS3006 Demo Board DC Power Supply Oscilloscope equivalent One 10X, 15pF//10M oscilloscope probe Model Agilent DSO1014A or To evaluate the TS3006 silicon timer, the following steps are to be performed: 1) Before connecting the DC power supply to the demo board, turn on the power supply, set the DC voltage to 5V, and then turn it off. TS3006-EVB Rev. 1.0 Page 2 TS3006 Demo Board Period vs RSET 120 PERIOD - s 100 80 60 40 20 0 0 2 4 6 8 10 12 RSET - M Figure 4. FOUT Period vs RSET Figure 5. Top Layer View #1 Figure 6. Top Layer View #2 Figure 7. Bottom Layer (GND) #1 Figure 8. Bottom Layer (GND) #2 Silicon Laboratories, Inc. 400 West Cesar Chavez, Austin, TX 78701 +1 (512) 416-8500 www.silabs.com Page 3 TS3006-EVB Rev. 1.0 Smart. Connected. Energy-Friendly Products Quality Support and Community www.silabs.com/products www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS(R), EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world's most energy friendly microcontrollers", Ember(R), EZLink(R), EZMac(R), EZRadio(R), EZRadioPRO(R), DSPLL(R), ISOmodem (R), Precision32(R), ProSLIC(R), SiPHY(R), USBXpress(R) and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com