16-Lane 4-Port Gen2 PCI Express(R) Switch 89HPES16T4AG2 Data Sheet (R) Device Overview Flexible Architecture with Numerous Configuration Options - Automatic per port link width negotiation to x8, x4, x2 or x1 - Automatic lane reversal on all ports - Automatic polarity inversion - Ability to load device configuration from serial EEPROM Legacy Support - PCI compatible INTx emulation - Bus locking Highly Integrated Solution - Incorporates on-chip internal memory for packet buffering and queueing - Integrates sixteen 5 Gbps embedded SerDes with 8b/10b encoder/decoder (no separate transceivers needed) * Receive equalization (RxEQ) Reliability, Availability, and Serviceability (RAS) Features - Internal end-to-end parity protection on all TLPs ensures data integrity even in systems that do not implement end-to-end CRC (ECRC) - Supports ECRC and Advanced Error Reporting - All internal data and control RAMs are SECDED ECC protected - Supports PCI Express Native Hot-Plug, Hot-Swap capable I/O - Compatible with Hot-Plug I/O expanders used on PC motherboards - Supports Hot-Swap The 89HPES16T4AG2 is a member of IDT's PRECISETM family of PCI Express(R) switching solutions. The PES16T4AG2 is a 16-lane, 4port Gen2 peripheral chip that performs PCI Express Base switching with a feature set optimized for high performance applications such as servers, storage, and communications/networking. It provides connectivity and switching functions between a PCI Express upstream port and up to three downstream ports and supports switching between downstream ports. Features High Performance PCI Express Switch - Sixteen 5 Gbps Gen2 PCI Express lanes - Four switch ports * One x8 or x4 upstream port * Up to three x4 downstream ports - Low latency cut-through switch architecture - Support for Max Payload Size up to 2048 bytes - One virtual channel - Eight traffic classes - PCI Express Base Specification Revision 2.0 compliant Block Diagram 4-Port Switch Core / 16 PCI Express Lanes Frame Buffer Port Arbitration Route Table Scheduler Transaction Layer Transaction Layer Transaction Layer Transaction Layer Data Link Layer Data Link Layer Data Link Layer Data Link Layer Multiplexer / Demultiplexer Multiplexer / Demultiplexer Multiplexer / Demultiplexer Multiplexer / Demultiplexer Phy Logical Layer Phy Logical Layer Phy Logical Layer Phy Logical Layer SerDes SerDes SerDes SerDes (Port 0) (Port 1) (Port 2) (Port 3) Figure 1 Internal Block Diagram IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc. 1 of 32 2013 Integrated Device Technology, Inc. May 23, 2013 DSC 6928 IDT 89HPES16T4AG2 Data Sheet Power Management - Utilizes advanced low-power design techniques to achieve low typical power consumption - Support PCI Express Power Management Interface specification (PCI-PM 2.0) - Unused SerDes are disabled. - Supports Advanced Configuration and Power Interface Specification, Revision 2.0 (ACPI) supporting active link state Testability and Debug Features - Built in Pseudo-Random Bit Stream (PRBS) generator - Numerous SerDes test modes - Ability to read and write any internal register via the SMBus - Ability to bypass link training and force any link into any mode - Provides statistics and performance counters Seven General Purpose Input/Output Pins - Each pin may be individually configured as an input or output - Each pin may be individually configured as an interrupt input - Some pins have selectable alternate functions Packaged in a 19mm x 19mm, 324-ball Flip Chip BGA with 1mm ball spacing Product Description Utilizing standard PCI Express interconnect, the PES16T4AG2 provides the most efficient fan-out solution for applications requiring high throughput, low latency, and simple board layout with a minimum number of board layers. It provides 16 GBps (128 Gbps) of aggregated, full-duplex switching capacity through 16 integrated serial lanes, using proven and robust IDT technology. Each lane provides 5 Gbps of bandwidth in both directions and is fully compliant with PCI Express Base Specification, Revision 2.0. The PES16T4AG2 is based on a flexible and efficient layered architecture. The PCI Express layer consists of SerDes, Physical, Data Link and Transaction layers in compliance with PCI Express Base specification Revision 2.0. The PES16T4AG2 can operate either as a store and forward or cut-through switch and is designed to switch memory and I/O transactions. It supports eight Traffic Classes (TCs) and one Virtual Channel (VC) with sophisticated resource management to enable efficient switching and I/O connectivity for servers, storage, and embedded processors with limited connectivity. Processor Processor Memory Memory Memory Memory North Bridge x8/x4 PES16T4AG2 x4 x4 PCI Express Slot I/O 10GbE x4 I/O 10GbE I/O SATA I/O SATA Figure 2 I/O Expansion Application SMBus Interface The PES16T4AG2 contains two SMBus interfaces. The slave interface provides full access to the configuration registers in the PES16T4AG2, allowing every configuration register in the device to be read or written by an external agent. The master interface allows the default configuration register values of the PES16T4AG2 to be overridden following a reset with values programmed in an external serial EEPROM. The master interface is also used by an external Hot-Plug I/O expander. Two pins make up each of the two SMBus interfaces. These pins consist of an SMBus clock pin and an SMBus data pin. The Master SMBus address is hardwired to 0x50, and the slave SMBus address is hardwired to 0x77. As shown in Figure 3, the master and slave SMBuses may be used in a unified or split configuration. In the unified configuration, shown in Figure 3(a), the master and slave SMBuses are tied together and the PES16T4AG2 acts both as a SMBus master as well as a SMBus slave on this bus. This requires that the SMBus master or processor that has access to PES16T4AG2 registers supports SMBus arbitration. In some systems, this SMBus master interface may be implemented using general purpose I/O pins on a processor or micro controller, and may not support SMBus arbitration. To support these systems, the PES16T4AG2 may be configured to operate in a split configuration as shown in Figure 3(b). In the split configuration, the master and slave SMBuses operate as two independent buses and thus multi-master arbitration is never required. The PES16T4AG2 supports reading and writing of the serial EEPROM on the master SMBus via the slave SMBus, allowing in system programming of the serial EEPROM. 2 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet PES16T4AG2 Processor SMBus Master Serial EEPROM ... Other SMBus Devices PES16T4AG2 SSMBCLK SSMBDAT SSMBCLK SSMBDAT MSMBCLK MSMBDAT MSMBCLK MSMBDAT Processor SMBus Master ... Other SMBus Devices Serial EEPROM (b) Split Configuration and Management Buses (a) Unified Configuration and Management Bus Figure 3 SMBus Interface Configuration Examples Hot-Plug Interface The PES16T4AG2 supports PCI Express Hot-Plug on each downstream port. To reduce the number of pins required on the device, the PES16T4AG2 utilizes an external I/O expander, such as that used on PC motherboards, connected to the SMBus master interface. Following reset and configuration, whenever the state of a Hot-Plug output needs to be modified, the PES16T4AG2 generates an SMBus transaction to the I/O expander with the new value of all of the outputs. Whenever a Hot-Plug input changes, the I/O expander generates an interrupt which is received on the IOEXPINTN input pin (alternate function of GPIO) of the PES16T4AG2. In response to an I/O expander interrupt, the PES16T4AG2 generates an SMBus transaction to read the state of all of the Hot-Plug inputs from the I/O expander. General Purpose Input/Output The PES16T4AG2 provides 7 General Purpose Input/Output (GPIO) pins that may be used by the system designer as bit I/O ports. Each GPIO pin may be configured independently as an input or output through software control. Some GPIO pins are shared with other on-chip functions. These alternate functions may be enabled via software, SMBus slave interface, or serial configuration EEPROM. 3 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Pin Description The following tables list the functions of the pins provided on the PES16T4AG2. Some of the functions listed may be multiplexed onto the same pin. The active polarity of a signal is defined using a suffix. Signals ending with an "N" are defined as being active, or asserted, when at a logic zero (low) level. All other signals (including clocks, buses, and select lines) will be interpreted as being active, or asserted, when at a logic one (high) level. Signal Type Name/Description PE0RP[3:0] PE0RN[3:0] I PCI Express Port 0 Serial Data Receive. Differential PCI Express receive pairs for port 0. Port 0 is the upstream port. PE0TP[3:0] PE0TN[3:0] O PCI Express Port 0 Serial Data Transmit. Differential PCI Express transmit pairs for port 0. Port 0 is the upstream port. PE1RP[3:0] PE1RN[3:0] I PCI Express Port 1 Serial Data Receive. Differential PCI Express receive pairs for port 1. PE1TP[3:0] PE1TN[3:0] O PCI Express Port 1 Serial Data Transmit. Differential PCI Express transmit pairs for port 1. PE2RP[3:0] PE2RN[3:0] I PCI Express Port 2 Serial Data Receive. Differential PCI Express receive pairs for port 2. PE2TP[3:0] PE2TN[3:0] O PCI Express Port 2 Serial Data Transmit. Differential PCI Express transmit pairs for port 2. PE3RP[3:0] PE3RN[3:0] I PCI Express Port 3 Serial Data Receive. Differential PCI Express receive pairs for port 3. PE3TP[3:0] PE3TN[3:0] O PCI Express Port 3 Serial Data Transmit. Differential PCI Express transmit pairs for port 3. PEREFCLKP PEREFCLKN I PCI Express Reference Clock. Differential reference clock pair input. This clock is used as the reference clock by on-chip PLLs to generate the clocks required for the system logic and on-chip SerDes. The frequency of the differential reference clock is set at 100 MHz. Table 1 PCI Express Interface Pins Signal Type Name/Description MSMBCLK I/O Master SMBus Clock. This bidirectional signal is used to synchronize transfers on the master SMBus which operates at 400 KHz. MSMBDAT I/O Master SMBus Data. This bidirectional signal is used for data on the master SMBus which operates at 400 KHz. SSMBCLK I/O Slave SMBus Clock. This bidirectional signal is used to synchronize transfers on the slave SMBus. SSMBDAT I/O Slave SMBus Data. This bidirectional signal is used for data on the slave SMBus. Table 2 SMBus Interface Pins 4 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Type Name/Description GPIO[0] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. Alternate function pin name: P2RSTN Alternate function pin type: Output Alternate function: Reset output for downstream port 2. GPIO[1] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. GPIO[2] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. Alternate function pin name: IOEXPINTN0 Alternate function pin type: Input Alternate function: I/O expander interrupt 0 input. GPIO[7] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. Alternate function pin name: GPEN Alternate function pin type: Output Alternate function: General Purpose Event (GPE) output GPIO[8] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. Alternate function pin name: P1RSTN Alternate function pin type: Output Alternate function: Reset output for downstream port 1 GPIO[9] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. Alternate function pin name: P3RSTN Alternate function pin type: Output Alternate function: Reset output for downstream port 3 GPIO[10] I/O General Purpose I/O. This pin can be configured as a general purpose I/O pin. Table 3 General Purpose I/O Pins 5 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Type Name/Description CCLKDS I Common Clock Downstream. The assertion of this pin indicates that all downstream ports are using the same clock source as that provided to downstream devices.This bit is used as the initial value of the Slot Clock Configuration bit in all of the Link Status Registers for downstream ports. The value may be overridden by modifying the SCLK bit in each downstream port's PCIELSTS register. CCLKUS I Common Clock Upstream. The assertion of this pin indicates that the upstream port is using the same clock source as the upstream device. This bit is used as the initial value of the Slot Clock Configuration bit in the Link Status Register for the upstream port. The value may be overridden by modifying the SCLK bit in the P0_PCIELSTS register. P01MERGEN I Port 0 and 1 Merge. P01MERGEN is an active low signal. It is pulled high internally via a 92K ohm resistor. When this pin is low, port 0 is merged with port 1 to form a single x8 port. The Serdes lanes associated with port 1 become lanes 4 through 7 of port 0. When this pin is high, port 0 and port 1 are not merged, and each operates as a single x4 port. P23MERGEN I Port 2 and 3 Merge. P23MERGEN is an active low signal. It is pulled high internally via a 92K ohm resistor. When this pin is low, port 2 is merged with port 3 to form a single x8 port. The Serdes lanes associated with port 3 become lanes 4 through 7 of port 2. When this pin is high, port 2 and port 3 are not merged, and each operates as a single x4 port. PERSTN I Fundamental Reset. Assertion of this signal resets all logic inside PES16T4AG2 and initiates a PCI Express fundamental reset. SWMODE[2:0] I Switch Mode. These configuration pins determine the PES16T4AG2 switch operating mode. 0x0 - Normal switch mode 0x1 - Normal switch mode with Serial EEPROM initialization 0x2 - through 0x7 Reserved These pins should be static and not change following the negation of PERSTN. Table 4 System Pins Signal Type Name/Description JTAG_TCK I JTAG Clock. This is an input test clock used to clock the shifting of data into or out of the boundary scan logic or JTAG Controller. JTAG_TCK is independent of the system clock with a nominal 50% duty cycle. JTAG_TDI I JTAG Data Input. This is the serial data input to the boundary scan logic or JTAG Controller. Table 5 Test Pins (Part 1 of 2) 6 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Type Name/Description JTAG_TDO O JTAG Data Output. This is the serial data shifted out from the boundary scan logic or JTAG Controller. When no data is being shifted out, this signal is tri-stated. JTAG_TMS I JTAG Mode. The value on this signal controls the test mode select of the boundary scan logic or JTAG Controller. JTAG_TRST_N I JTAG Reset. This active low signal asynchronously resets the boundary scan logic and JTAG TAP Controller. An external pull-up on the board is recommended to meet the JTAG specification in cases where the tester can access this signal. However, for systems running in functional mode, one of the following should occur: 1) actively drive this signal low with control logic 2) statically drive this signal low with an external pull-down on the board Table 5 Test Pins (Part 2 of 2) Signal Type Name/Description REFRES0 I/O Port 0 External Reference Resistor. Provides a reference for the Port 0 SerDes bias currents and PLL calibration circuitry. A 3 kOhm +/- 1% resistor should be connected from this pin to ground. REFRES1 I/O Port 1 External Reference Resistor. Provides a reference for the Port 1 SerDes bias currents and PLL calibration circuitry. A 3 kOhm +/- 1% resistor should be connected from this pin to ground. REFRES2 I/O Port 2 External Reference Resistor. Provides a reference for the Port 2 SerDes bias currents and PLL calibration circuitry. A 3 kOhm +/- 1% resistor should be connected from this pin to ground. REFRES3 I/O Port 3 External Reference Resistor. Provides a reference for the Port 3 SerDes bias currents and PLL calibration circuitry. A 3 kOhm +/- 1% resistor should be connected from this pin to ground. VDDCORE I Core VDD. Power supply for core logic. VDDI/O I I/O VDD. LVTTL I/O buffer power supply. VDDPEA I PCI Express Analog Power. Serdes analog power supply (1.0V). VDDPEHA I PCI Express Analog High Power. Serdes analog power supply (2.5V). VDDPETA I PCI Express Transmitter Analog Voltage. Serdes transmitter analog power supply (1.0V). VSS I Ground. Table 6 Power, Ground, and SerDes Resistor Pins 7 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Pin Characteristics Note: Some input pads of the PES16T4AG2 do not contain internal pull-ups or pull-downs. Unused inputs should be tied off to appropriate levels. This is especially critical for unused control signal inputs which, if left floating, could adversely affect operation. Also, any input pin left floating can cause a slight increase in power consumption. Function I/O Type Internal Resistor1 Type Buffer PE0RN[3:0] I Serial Link PE0RP[3:0] I PCIe differential2 PE0TN[3:0] O PE0TP[3:0] O PE1RN[3:0] I PE1RP[3:0] I PE1TN[3:0] O PE1TP[3:0] O PE2RN[3:0] I PE2RP[3:0] I PE2TN[3:0] O PE2TP[3:0] O PE3RN[3:0] I PE3RP[3:0] I PE3TN[3:0] O PE3TP[3:0] O PEREFCLKN I HCSL PEREFCLKP I Diff. Clock Input MSMBCLK I/O STI3 pull-up on board MSMBDAT I/O STI pull-up on board SSMBCLK I/O STI pull-up on board SSMBDAT I/O STI pull-up on board General Purpose I/O GPIO[10:7, 2:0] I/O LVTTL STI, High Drive pull-up System Pins CCLKDS I LVTTL Input pull-up CCLKUS I Input pull-up P01MERGEN I PCI Express Interface SMBus EJTAG / JTAG Pin Name Notes Refer to Table 8 pull-up P23MERGEN I PERSTN I STI pull-up SWMODE[2:0] I Input pull-down JTAG_TCK I STI pull-up STI pull-up LVTTL JTAG_TDI I JTAG_TDO O JTAG_TMS I STI pull-up JTAG_TRST_N I STI pull-up Table 7 Pin Characteristics (Part 1 of 2) 8 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Type Buffer I/O Type REFRES0 I/O Analog Input REFRES1 I/O REFRES2 I/O REFRES3 I/O Function SerDes Reference Resistors Pin Name Internal Resistor1 Notes Table 7 Pin Characteristics (Part 2 of 2) 1. Internal resistor values under typical operating conditions are 92K for pull-up and 90K for pull-down. 2. All receiver pins set the DC common mode voltage to ground. All transmitters must be AC coupled to the media. 3. Schmitt Trigger Input (STI). 9 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Logic Diagram -- PES16T4AG2 Reference Clocks PEREFCLKP PEREFCLKN PE0TP[0] PE0TN[0] PE0RP[0] PE0RN[0] PE0RP[3] PE0RN[3] PE0TP[3] PE0TN[3] PCI Express Switch SerDes Input Port 1 PE1RP[0] PE1RN[0] PE1TP[0] PE1TN[0] PE1RP[3] PE1RN[3] PE1TP[3] PE1TN[3] PCI Express Switch SerDes Input Port 2 PE2RP[0] PE2RN[0] PE2TP[0] PE2TN[0] PE2RP[3] PE2RN[3] PE2TP[3] PE2TN[3] PCI Express Switch SerDes Input Port 3 PE3RP[0] PE3RN[0] PE3TP[0] PE3TN[0] ... ... PCI Express Switch SerDes Input Port 0 ... ... ... ... ... ... PE3RP[3] PE3RN[3] PE3TP[3] PE3TN[3] PES16T4AG2 7 Master SMBus Interface Slave SMBus Interface System Pins MSMBCLK MSMBDAT JTAG_TCK JTAG_TDI JTAG_TDO JTAG_TMS JTAG_TRST_N SSMBCLK SSMBDAT CCLKDS CCLKUS P01MERGEN P23MERGEN PERSTN SWMODE[2:0] GPIO[10:7,2:0] REFRES0 REFRES1 REFRES2 REFRES3 3 PCI Express Switch SerDes Output Port 0 PCI Express Switch SerDes Output Port 1 PCI Express Switch SerDes Output Port 2 PCI Express Switch SerDes Output Port 3 General Purpose I/O JTAG Pins SerDes Reference Resistors VDDCORE VDDI/O VDDPEA VDDPEHA VSS Power/Ground VDDPETA Figure 4 PES16T4AG2 Logic Diagram 10 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet System Clock Parameters Values based on systems running at recommended supply voltages and operating temperatures, as shown in Tables 12 and 14. Parameter Description Condition Min Typical Max Unit 100 1001 MHz RefclkFREQ Input reference clock frequency range TC-RISE Rising edge rate Differential 0.6 4 V/ns TC-FALL Falling edge rate Differential 0.6 4 V/ns VIH Differential input high voltage Differential +150 VIL Differential input low voltage Differential VCROSS Absolute single-ended crossing point voltage Single-ended VCROSS-DELTA Variation of VCROSS over all rising clock edges Single-ended VRB Ring back voltage margin Differential -100 TSTABLE Time before VRB is allowed Differential 500 TPERIOD-AVG Average clock period accuracy -300 2800 ppm TPERIOD-ABS Absolute period, including spread-spectrum and jitter 9.847 10.203 ns TCC-JITTER Cycle to cycle jitter 150 ps VMAX Absolute maximum input voltage +1.15 V VMIN Absolute minimum input voltage -0.3 Duty Cycle Duty cycle 40 Rise/Fall Matching Single ended rising Refclk edge rate versus falling Refclk edge rate ZC-DC Clock source output DC impedance mV +250 -150 mV +550 mV +140 mV +100 mV ps V 60 20 % % 40 60 Table 8 Input Clock Requirements 1. The input clock frequency is set at 100 MHz. AC Timing Characteristics Parameter Gen 1 Description Gen 2 Min1 Typ1 Max1 Min1 Typ1 Max1 399.88 400 400.12 199.94 200 200.06 Units PCIe Transmit UI Unit Interval TTX-EYE Minimum Tx Eye Width TTX-EYE-MEDIAN-toMAX-JITTER Maximum time between the jitter median and maximum deviation from the median TTX-RISE, TTX-FALL TX Rise/Fall Time: 20% - 80% TTX- IDLE-MIN Minimum time in idle 0.75 0.75 0.125 ps UI UI 0.125 0.15 UI 20 20 UI Table 9 PCIe AC Timing Characteristics (Part 1 of 2) 11 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Parameter Gen 1 Description Min1 1 Typ Gen 2 1 Max 1 Min Typ1 Max1 Units TTX-IDLE-SET-TO-IDLE Maximum time to transition to a valid Idle after sending an Idle ordered set 8 8 ns TTX-IDLE-TO-DIFF- 8 8 ns 1.3 1.3 ns Maximum time to transition from valid idle to diff data DATA TTX-SKEW Transmitter data skew between any 2 lanes TMIN-PULSED Minimum Instantaneous Lone Pulse Width NA TTX-HF-DJ-DD Transmitter Deterministic Jitter > 1.5MHz Bandwidth NA 0.15 UI TRF-MISMATCH Rise/Fall Time Differential Mismatch NA 0.1 UI 200.06 ps 0.9 UI PCIe Receive UI Unit Interval 399.88 400 400.12 TRX-EYE (with jitter) Minimum Receiver Eye Width (jitter tolerance) TRX-EYE-MEDIUM TO Max time between jitter median & max deviation 0.3 TRX-SKEW Lane to lane input skew 20 TRX-HF-RMS 1.5 -- 100 MHz RMS jitter (common clock) TRX-HF-DJ-DD 0.4 199.94 0.4 UI UI MAX JITTER 8 ns NA 3.4 ps Maximum tolerable DJ by the receiver (common clock) NA 88 ps TRX-LF-RMS 10 KHz to 1.5 MHz RMS jitter (common clock) NA 4.2 ps TRX-MIN-PULSE Minimum receiver instantaneous eye width NA 0.6 UI Table 9 PCIe AC Timing Characteristics (Part 2 of 2) 1. Minimum, Typical, and Maximum values meet the requirements under PCI Specification 2.0 Signal Symbol Reference Min Max Unit Edge Timing Diagram Reference GPIO GPIO[10:7,2:0]1 Tpw2 None 50 -- ns Table 10 GPIO AC Timing Characteristics 1. GPIO signals must meet the setup and hold times if they are synchronous or the minimum pulse width if they are asynchronous. 2. The values for this symbol were determined by calculation, not by testing. 12 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Symbol Reference Edge Min Max Unit Timing Diagram Reference Tper_16a none 50.0 -- ns See Figure 5. 10.0 25.0 ns 2.4 -- ns 1.0 -- ns -- 20 ns -- 20 ns 25.0 -- ns JTAG JTAG_TCK Thigh_16a, Tlow_16a JTAG_TMS1, JTAG_TDI Tsu_16b JTAG_TCK rising Thld_16b JTAG_TDO Tdo_16c Tdz_16c JTAG_TRST_N JTAG_TCK falling 2 Tpw_16d2 none Table 11 JTAG AC Timing Characteristics 1. The JTAG specification, IEEE 1149.1, recommends that JTAG_TMS should be held at 1 while the signal applied at JTAG_TRST_N changes from 0 to 1. Otherwise, a race may occur if JTAG_TRST_N is deasserted (going from low to high) on a rising edge of JTAG_TCK when JTAG_TMS is low, because the TAP controller might go to either the Run-Test/Idle state or stay in the Test-Logic-Reset state. 2. The values for this symbol were determined by calculation, not by testing. Tlow_16a Tper_16a Thigh_16a JTAG_TCK Thld_16b Tsu_16b JTAG_TDI Thld_16b Tsu_16b JTAG_TMS Tdo_16c Tdz_16c JTAG_TDO Tpw_16d JTAG_TRST_N Figure 5 JTAG AC Timing Waveform 13 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Recommended Operating Supply Voltages Symbol Parameter Minimum Typical Maximum Unit 0.9 1.0 1.1 V VDDCORE Internal logic supply VDDI/O I/O supply except for SerDes LVPECL/CML 3.135 3.3 3.465 V VDDPEA1 PCI Express Analog Power 0.95 1.0 1.1 V 2 PCI Express Analog High Power 2.25 2.5 2.75 V 1 VDDPETA PCI Express Transmitter Analog Voltage 0.95 1.0 1.1 V VSS Common ground 0 0 0 V VDDPEHA Table 12 PES16T4AG2 Operating Voltages VDDPEA and VDDPETA should have no more than 25mVpeak-peak AC power supply noise superimposed on the 1.0V nominal DC value. 1. 2. V PEHA should have no more than 50mV DD peak-peak AC power supply noise superimposed on the 2.5V nominal DC value. Absolute Maximum Voltage Rating Core Supply PCIe Analog Supply PCIe Analog High Supply PCIe Transmitter Supply I/O Supply 1.5V 1.5V 4.6V 1.5V 4.6V Table 13 PES16T4AG2 Absolute Maximum Voltage Rating Warning: For proper and reliable operation in adherence with this data sheet, the device should not exceed the recommended operating voltages in Table 12. The absolute maximum operating voltages in Table 13 are offered to provide guidelines for voltage excursions outside the recommended voltage ranges. Device functionality is not guaranteed at these conditions and sustained operation at these values or any exposure to voltages outside the maximum range may adversely affect device functionality and reliability. Power-Up/Power-Down Sequence During power supply ramp-up, VDDCORE must remain at least 1.0V below VDDI/O at all times. There are no other power-up sequence requirements for the various operating supply voltages. The power-down sequence can occur in any order. Recommended Operating Temperature Grade Temperature Commercial 0C to +70C Ambient Industrial -40C to +85C Ambient Table 14 PES16T4AG2 Operating Temperatures 14 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Power Consumption Typical power is measured under the following conditions: 25C Ambient, 35% total link usage on all ports, typical voltages defined in Table 12 (and also listed below). Maximum power is measured under the following conditions: 70C Ambient, 85% total link usage on all ports, maximum voltages defined in Table 12 (and also listed below). Core Supply PCIe Analog Supply PCIe Analog High Supply PCIe Termination Supply Typ 1.0V Max 1.1V Typ 1.0V Max 1.1V Typ 2.5V Max 2.75V Typ 1.0V Max 1.1V Typ 3.3V Max 3.465V mA 413 905 901 963 110 123 360 429 2 2 Watts 0.41 1.0 0.90 1.06 0.28 0.34 0.36 0.47 0.007 0.007 mA 413 905 901 963 110 123 180 215 2 2 Watts 0.41 1.0 0.90 1.06 0.28 0.34 0.18 0.24 0.01 0.01 Number of active Lanes per Port 8/4/4 4/4/4/4 I/O Supply Total Typ Power Max Power 1.96 2.87 1.78 2.64 Table 15 PES16T4AG2 Power Consumption Thermal Considerations This section describes thermal considerations for the PES16T4AG2 (19mm2 FCBGA324 package). The data in Table 16 below contains information that is relevant to the thermal performance of the PES16T4AG2 switch. Symbol TJ(max) TA(max) JA(effective) Parameter Value Units Conditions 125 oC Maximum 70 oC Maximum 16.8 oC/W Zero air flow 10.1 oC/W 1 m/S air flow 9.2 oC/W 2 m/S air flow Junction Temperature Ambient Temperature Effective Thermal Resistance, Junction-to-Ambient JB Thermal Resistance, Junction-to-Board 4.1 oC/W JC Thermal Resistance, Junction-to-Case 0.3 o P Power Dissipation of the Device 2.87 Watts C/W Maximum Table 16 Thermal Specifications for PES16T4AG2, 19x19 mm FCBGA324 Package Note: It is important for the reliability of this device in any user environment that the junction temperature not exceed the TJ(max) value specified in Table 16. Consequently, the effective junction to ambient thermal resistance (JA) for the worst case scenario must be maintained below the value determined by the formula: JA = (TJ(max) - TA(max))/P Given that the values of TJ(max), TA(max), and P are known, the value of desired JA becomes a known entity to the system designer. How to achieve the desired JA is left up to the board or system designer, but in general, it can be achieved by adding the effects of JC (value provided in Table 16), thermal resistance of the chosen adhesive (CS), that of the heat sink (SA), amount of airflow, and properties of the circuit board (number of layers and size of the board). As a general guideline, this device will not need a heat sink if the board has 8 or more layers AND the board size is larger than 4"x12" AND airflow in excess of 0.5 m/s is available. It is strongly recommended that users perform their own thermal analysis for their own board and system design scenarios. 15 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet DC Electrical Characteristics Values based on systems running at recommended supply voltages, as shown in Table 12. Note: See Table 7, Pin Characteristics, for a complete I/O listing. I/O Type Serial Link Parameter Description Gen1 Min1 Typ1 Gen2 Max1 Min1 Typ1 Unit Conditions Max1 PCIe Transmit VTX-DIFFp-p Differential peak-to-peak output voltage 800 1200 800 1200 mV VTX-DIFFp-p-LOW Low-Drive Differential Peak to Peak Output Voltage 400 1200 400 1200 mV VTX-DE-RATIO- De-emphasized differential output voltage -3 -4 -3.0 -3.5 -4.0 dB -5.5 -6.0 -6.5 dB 3.6 V 3.5dB 6.0dB De-emphasized differential output voltage VTX-DC-CM DC Common mode voltage VTX-CM-ACP RMS AC peak common mode output voltage VTX-DE-RATIO- NA 0 3.6 0 20 mV VTX-CM-DC-active- Abs delta of DC common mode voltage between L0 and idle idle-delta 100 100 mV Abs delta of DC common mode voltage between D+ and D- 25 25 mV delta VTX-Idle-DiffP Electrical idle diff peak output 20 20 mV RLTX-DIFF Transmitter Differential Return loss 10 10 dB 0.05 - 1.25GHz 8 dB 1.25 - 2.5GHz RLTX-CM Transmitter Common Mode Return loss 6 6 dB ZTX-DIFF-DC DC Differential TX impedance 80 120 VTX-CM-ACpp Peak-Peak AC Common 100 mV VTX-DC-CM Transmit Driver DC Common Mode Voltage 3.6 V 600 mV VTX-CM-DC-line- 100 NA 0 3.6 VTX-RCV-DETECT The amount of voltage change allowed during Receiver Detection ITX-SHORT Transmitter Short Circuit Current Limit 120 0 600 0 90 90 mA Table 17 DC Electrical Characteristics (Part 1 of 2) 16 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet I/O Type Serial Link (cont.) Parameter Description Gen1 Min1 Typ1 Gen2 Max1 Min1 1200 120 Typ1 Unit Conditions Max1 PCIe Receive VRX-DIFFp-p Differential input voltage (peak-topeak) 175 RLRX-DIFF Receiver Differential Return Loss 10 1200 mV 10 dB 8 RLRX-CM Receiver Common Mode Return Loss 6 ZRX-DIFF-DC Differential input impedance (DC) 80 100 ZRX--DC DC common mode impedance 40 50 ZRX-COMM-DC Powered down input common mode impedance (DC) 200k 350k 1.25 - 2.5GHz 6 dB 120 Refer to return loss spec 60 40 60 50k ZRX-HIGH-IMP-DC- DC input CM input impedance for V>0 during reset or power down POS 50k 50k ZRX-HIGH-IMP-DC- DC input CM input impedance for V<0 during reset or power down NEG 1.0k 1.0k 175 mV 150 mV VRX-IDLE-DET- Electrical idle detect threshold 65 175 65 0.05 - 1.25GHz DIFFp-p VRX-CM-ACp Receiver AC common-mode peak voltage 150 VRX-CM-ACp PCIe REFCLK CIN Input Capacitance 1.5 -- 1.5 -- IOL -- 2.5 IOH -- IOL pF -- -- 2.5 -- mA VOL = 0.4v -5.5 -- -- -5.5 -- mA VOH = 1.5V -- 12.0 -- -- 12.0 -- mA VOL = 0.4v IOH -- -20.0 -- -- -20.0 -- mA VOH = 1.5V Other I/Os LOW Drive Output High Drive Output Schmitt Trigger Input (STI) VIL -0.3 -- 0.8 -0.3 -- 0.8 V -- VIH 2.0 -- VDDI/O + 0.5 2.0 -- VDDI/O + 0.5 V -- Input VIL -0.3 -- 0.8 -0.3 -- 0.8 V -- VIH 2.0 -- VDDI/O + 0.5 2.0 -- VDDI/O + 0.5 V -- CIN -- -- 8.5 -- -- 8.5 pF -- Inputs -- -- + 10 -- -- + 10 A VDDI/O (max) I/OLEAK W/O Pull-ups/downs -- -- + 10 -- -- + 10 A VDDI/O (max) I/OLEAK WITH Pull-ups/downs -- -- + 80 -- -- + 80 A VDDI/O (max) Capacitance Leakage Table 17 DC Electrical Characteristics (Part 2 of 2) 1. Minimum, Typical, and Maximum values meet the requirements under PCI Specification 2.0. 17 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Package Pinout -- 324-BGA Signal Pinout for PES16T4AG2 The following table lists the pin numbers and signal names for the PES16T4AG2 device. Pin Function Alt Pin Function Alt Pin Function Alt Pin Function A1 VSS B17 NC D15 VDDCORE F13 VSS A2 VDDI/O B18 NC D16 VSS F14 NC A3 P01MERGEN C1 PE3TP02 D17 VSS F15 NC A4 P23MERGEN C2 PE3TN02 D18 VSS F16 VSS A5 VSS C3 VSS E1 PE3TP01 F17 NC A6 VDDI/O C4 PE3RP02 E2 PE3TN01 F18 NC A7 VSS C5 PE3RN02 E3 VSS G1 VSS A8 JTAG_TDI C6 VSS E4 PE3RP01 G2 VSS A9 MSMBDAT C7 JTAG_TCK E5 PE3RN01 G3 VSS A10 VDDI/O C8 JTAG_TRST_N E6 VDDCORE G4 VDDCORE A11 VSS C9 SSMBDAT E7 VDDCORE G5 VDDCORE A12 GPIO_00 C10 CCLKDS E8 VDDCORE G6 VDDPEA A13 VDDI/O C11 SWMODE_2 E9 VSS G7 VDDPEA A14 VDDI/O C12 GPIO_02 1 E10 VDDCORE G8 VDDCORE A15 VSS C13 GPIO_09 1 E11 VDDCORE G9 VDDCORE A16 VSS C14 NC E12 VDDCORE G10 VDDCORE A17 VDDI/O C15 NC E13 VDDCORE G11 VSS A18 VDDI/O C16 VSS E14 NC G12 VDDPEA B1 PE3TP03 C17 NC E15 NC G13 VDDPEA B2 PE3TN03 C18 NC E16 VSS G14 VDDCORE B3 VSS D1 VSS E17 NC G15 VDDCORE B4 PE3RP03 D2 VSS E18 NC G16 VSS B5 PE3RN03 D3 VSS F1 PE3TP00 G17 VSS B6 VDDI/O D4 VDDCORE F2 PE3TN00 G18 VSS B7 VDDI/O D5 VDDCORE F3 VSS H1 PE2TP03 B8 JTAG_TMS D6 VSS F4 PE3RP00 H2 PE2TN03 B9 SSMBCLK D7 JTAG_TDO F5 PE3RN00 H3 VSS B10 VDDI/O D8 MSMBCLK F6 VSS H4 PE2RP03 B11 SWMODE_1 D9 CCLKUS F7 VSS H5 PE2RN03 B12 GPIO_01 D10 SWMODE_0 F8 VDDCORE H6 VDDPEA B13 GPIO_10 D11 PERSTN F9 VSS H7 VDDPEA B14 NC D12 GPIO_07 1 F10 VDDCORE H8 VDDCORE B15 NC D13 GPIO_08 1 F11 VSS H9 VDDCORE B16 VSS D14 VDDCORE F12 VSS H10 VDDCORE 1 Alt Table 18 PES16T4AG2 324-pin Signal Pin-Out (Part 1 of 3) 18 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Pin Function Alt Pin Function Alt Pin Function Alt Pin Function H11 VSS K13 VDDPETA M15 NC P17 VDDCORE H12 VDDPEA K14 VDDCORE M16 VSS P18 VSS H13 VDDPEA K15 NC M17 NC R1 VSS H14 NC K16 VSS M18 NC R2 VDDCORE H15 NC K17 NC N1 VSS R3 VDDCORE H16 VSS K18 NC N2 VSS R4 PE1RP03 H17 NC L1 PE2TP01 N3 VSS R5 PE1RP02 H18 NC L2 PE2TN01 N4 VDDCORE R6 NC J1 PE2TP02 L3 VSS N5 VDDCORE R7 PE1RP01 J2 PE2TN02 L4 PE2RP01 N6 VSS R8 PE1RP00 J3 VSS L5 PE2RN01 N7 VSS R9 VDDCORE J4 PE2RP02 L6 VDDPETA N8 VDDPEA R10 PE0RP03 J5 PE2RN02 L7 VDDPETA N9 VDDPEHA R11 PE0RP02 J6 VDDPEHA L8 VDDPEA N10 VDDPETA R12 VDDCORE J7 VDDPEHA L9 VDDPEHA N11 VDDPEA R13 PE0RP01 J8 VDDCORE L10 VDDPETA N12 VDDPEHA R14 PE0RP00 J9 VSS L11 VDDPEA N13 VSS R15 VDDCORE J10 VDDCORE L12 VDDPEHA N14 VSS R16 VDDCORE J11 VSS L13 VDDPETA N15 VDDCORE R17 VDDCORE J12 VDDPEHA L14 NC N16 VSS R18 VSS J13 VDDPEHA L15 NC N17 VSS T1 VSS J14 NC L16 VSS N18 VSS T2 VSS J15 NC L17 NC P1 VSS T3 VSS J16 VSS L18 NC P2 VDDCORE T4 VSS J17 NC M1 PE2TP00 P3 VDDCORE T5 VSS J18 NC M2 PE2TN00 P4 PE1RN03 T6 VSS K1 REFRES2 M3 VSS P5 PE1RN02 T7 VSS K2 REFRES3 M4 PE2RP00 P6 VDDCORE T8 VSS K3 VSS M5 PE2RN00 P7 PE1RN01 T9 VSS K4 VDDCORE M6 VDDPETA P8 PE1RN00 T10 VSS K5 VDDCORE M7 VDDPETA P9 VDDCORE T11 VSS K6 VDDPETA M8 VDDPEA P10 PE0RN03 T12 VSS K7 VDDPETA M9 VDDPEHA P11 PE0RN02 T13 VSS K8 VDDCORE M10 VDDPETA P12 VDDCORE T14 VSS K9 VSS M11 VDDPEA P13 PE0RN01 T15 VSS K10 VDDCORE M12 VDDPEHA P14 PE0RN00 T16 VSS K11 VSS M13 VSS P15 VDDCORE T17 VSS K12 VDDPETA M14 NC P16 VDDCORE T18 VSS Alt Table 18 PES16T4AG2 324-pin Signal Pin-Out (Part 2 of 3) 19 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Pin Function Alt Pin Function Alt Pin Function Alt Pin Function U1 VSS U10 PE0TN03 V1 VSS V10 PE0TP03 U2 PEREFCLKN U11 PE0TN02 V2 PEREFCLKP V11 PE0TP02 U3 VSS U12 VSS V3 VSS V12 VSS U4 PE1TN03 U13 PE0TN01 V4 PE1TP03 V13 PE0TP01 U5 PE1TN02 U14 PE0TN00 V5 PE1TP02 V14 PE0TP00 U6 REFRES1 U15 VSS V6 REFRES0 V15 VSS U7 PE1TN01 U16 VSS V7 PE1TP01 V16 VSS U8 PE1TN00 U17 VSS V8 PE1TP00 V17 VSS U9 VSS U18 VSS V9 VSS V18 VSS Alt Table 18 PES16T4AG2 324-pin Signal Pin-Out (Part 3 of 3) Alternate Signal Functions Pin GPIO Alternate A12 GPIO_00 P2RSTN C12 GPIO_02 IOEXPINTN0 D12 GPIO_07 GPEN D13 GPIO_08 P1RSTN C13 GPIO_09 P3RSTN Table 19 PES16T4AG2 Alternate Signal Functions No Connection Pins NC Pins NC Pins NC Pins NC Pins B14 E15 H17 L14 B15 E17 H18 L15 B17 E18 J14 L17 B18 F14 J15 L18 C14 F15 J17 M14 C15 F17 J18 M15 C17 F18 K15 M17 C18 H14 K17 M18 E14 H15 K18 R6 Table 20 PES16T4AG2 No Connection Pins 20 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Power Pins VDDCore VDDCore VDDCore VDDI/O VDDPEA VDDPEHA VDDPETA D4 G9 N15 A2 G6 J6 K6 D5 G10 P2 A6 G7 J7 K7 D14 G14 P3 A10 G12 J12 K12 D15 G15 P6 A13 G13 J13 K13 E6 H8 P9 A14 H6 L9 L6 E7 H9 P12 A17 H7 L12 L7 E8 H10 P15 A18 H12 M9 L10 E10 J8 P16 B6 H13 M12 L13 E11 J10 P17 B7 L8 N9 M6 E12 K4 R2 B10 L11 N12 M7 E13 K5 R3 M8 M10 F8 K8 R9 M11 N10 F10 K10 R12 N8 G4 K14 R15 N11 G5 N4 R16 G8 N5 R17 Table 21 PES16T4AG2 Power Pins 21 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Ground Pins Vss Vss Vss Vss Vss Vss A1 D18 G17 M16 T3 U3 A5 E3 G18 N1 T4 U9 A7 E9 H3 N2 T5 U12 A11 E16 H11 N3 T6 U15 A15 F3 H16 N6 T7 U16 A16 F6 J3 N7 T8 U17 B3 F7 J9 N13 T9 U18 B16 F9 J11 N14 T10 V1 C3 F11 J16 N16 T11 V3 C6 F12 K3 N17 T12 V9 C16 F13 K9 N18 T13 V12 D1 F16 K11 P1 T14 V15 D2 G1 K16 P18 T15 V16 D3 G2 L3 R1 T16 V17 D6 G3 L16 R18 T17 V18 D16 G11 M3 T1 T18 D17 G16 M13 T2 U1 Table 22 PES16T4AG2 Ground Pins 22 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signals Listed Alphabetically Signal Name I/O Type Location Signal Category CCLKDS I C10 System CCLKUS I D9 GPIO_00 I/O A12 GPIO_01 I/O B12 GPIO_02 I/O C12 GPIO_07 I/O D12 GPIO_08 I/O D13 GPIO_09 I/O C13 GPIO_10 I/O B13 JTAG_TCK I C7 JTAG_TDI I A8 JTAG_TDO O D7 JTAG_TMS I B8 JTAG_TRST_N I C8 MSMBCLK I/O D8 MSMBDAT I/O A9 NO CONNECTION General Purpose Input/Output JTAG SMBus See Table 20 P01MERGEN I A3 P23MERGEN I A4 PE0RN00 I P14 PE0RN01 I P13 PE0RN02 I P11 PE0RN03 I P10 PE0RP00 I R14 PE0RP01 I R13 PE0RP02 I R11 PE0RP03 I R10 PE0TN00 O U14 PE0TN01 O U13 PE0TN02 O U11 PE0TN03 O U10 PE0TP00 O V14 PE0TP01 O V13 PE0TP02 O V11 System PCI Express Table 23 89PES16T4AG2 Alphabetical Signal List (Part 1 of 3) 23 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Name I/O Type Location Signal Category PE0TP03 O V10 PCI Express (Cont.) PE1RN00 I P8 PE1RN01 I P7 PE1RN02 I P5 PE1RN03 I P4 PE1RP00 I R8 PE1RP01 I R7 PE1RP02 I R5 PE1RP03 I R4 PE1TN00 O U8 PE1TN01 O U7 PE1TN02 O U5 PE1TN03 O U4 PE1TP00 O V8 PE1TP01 O V7 PE1TP02 O V5 PE1TP03 O V4 PE2RN00 I M5 PE2RN01 I L5 PE2RN02 I J5 PE2RN03 I H5 PE2RP00 I M4 PE2RP01 I L4 PE2RP02 I J4 PE2RP03 I H4 PE2TN00 O M2 PE2TN01 O L2 PE2TN02 O J2 PE2TN03 O H2 PE2TP00 O M1 PE2TP01 O L1 PE2TP02 O J1 PE2TP03 O H1 PE3RN00 I F5 PE3RN01 I E5 PE3RN02 I C5 Table 23 89PES16T4AG2 Alphabetical Signal List (Part 2 of 3) 24 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Name I/O Type Location Signal Category PE3RN03 I B5 PCI Express (Cont.) PE3RP00 I F4 PE3RP01 I E4 PE3RP02 I C4 PE3RP03 I B4 PE3TN00 O F2 PE3TN01 O E2 PE3TN02 O C2 PE3TN03 O B2 PE3TP00 O F1 PE3TP01 O E1 PE3TP02 O C1 PE3TP03 O B1 PEREFCLKN I U2 PEREFCLKP I V2 PERSTN I D11 System REFRES0 I/O V6 SerDes Reference Resistors REFRES1 I/O U6 REFRES2 I/O K1 REFRES3 I/O K2 SSMBCLK I/O B9 SSMBDAT I/O C9 SWMODE_0 I D10 SWMODE_1 I B11 SWMODE_2 I C11 SMBus System VDDCORE, VDDI/O, VDDPEA, VDDPEHA, VDDPETA See Table 21 for a listing of power pins. VSS See Table 22 for a listing of ground pins. Table 23 89PES16T4AG2 Alphabetical Signal List (Part 3 of 3) 25 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet PES16T4AG2 Package Trace Length Signal Name Conductor Length (microns) PE0RN00 6476.76 PE0RP00 6852.44 PE0RN01 5193.18 PE0RP01 5556.44 PE0RN02 4122.07 PE0RP02 4488.70 PE0RN03 4026.18 PE0RP03 4426.98 PE0TN00 9779.14 PE0TP00 9830.77 PE0TN01 8725.88 PE0TP01 8836.41 PE0TN02 7608.89 PE0TP02 7657.42 PE0TN03 7295.70 PE0TP03 7361.98 PE1RN00 3844.19 PE1RP00 4219.88 PE1RN01 4261.05 PE1RP01 4636.74 PE1RN02 5263.73 PE1RP02 5639.42 PE1RN03 6331.07 PE1RP03 6726.84 PE1TN00 7518.88 PE1TP00 7605.87 PE1TN01 7393.75 PE1TP01 7528.38 PE1TN02 8469.86 PE1TP02 8583.77 PE1TN03 8516.01 PE1TP03 8650.63 PE2RN00 2227.99 Table 24 Signal Trace Length (Part 1 of 2) 26 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Signal Name Conductor Length (microns) PE2RP00 2600.58 PE2RN01 1881.27 PE2RP01 2256.96 PE2RN02 2105.60 PE2RP02 2470.94 PE2RN03 2835.27 PE2RP03 3207.86 PE2TN00 5462.64 PE2TP00 5576.55 PE2TN01 5163.54 PE2TP01 5273.30 PE2TN02 5389.58 PE2TP02 5512.25 PE2TN03 5310.88 PE2TP03 5451.71 PE3RN00 9181.06 PE3RP00 9541.52 PE3RN01 8602.32 PE3RP01 8994.21 PE3RN02 8220.08 PE3RP02 8604.05 PE3RN03 8906.71 PE3RP03 9193.82 PE3TN00 10606.88 PE3TP00 10747.72 PE3TN01 10972.20 PE3TP01 11117.18 PE3TN02 11862.08 PE3TP02 11978.06 PE3TN03 11822.86 PE3TP03 11870.23 PE0REFCLKN 12558.62 PE0REFCLKP 12641.05 Table 24 Signal Trace Length (Part 2 of 2) 27 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet PES16T4AG2 Pinout -- Top View 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A A B B C C D D E E F F G G H H J J K X X L X X X M X X X M X N X N X K X L P P R R T T U U V V 1 2 3 4 VDDCore (Power) VDDI/O (Power) 5 x 6 7 8 9 10 VDDPETA (Power) VDDPEA (Power) 11 12 13 Vss (Ground) 14 15 16 17 18 Signals No Connect VDDPEHA (Power) 28 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet PES16T4AG2 Package Drawing -- 324-Pin AL324/AR324 29 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet PES16T4AG2 Package Drawing -- Page Two 30 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Revision History January 15, 2009: Publication of final data sheet. February 11, 2009: Revised AC Timing Characteristics table and DC Electrical Characteristics table to correct typos. March 6, 2009: Added industrial temperature. April 7, 2009: In Valid Combinations, changed ZB to ZC silicon for commercial temperature. April 17, 2009: In Table 15, Power Dissipation value was changed to 2.87. February 2, 2010: Added new section Absolute Maximum Voltage Rating with table. September 13, 2010: In Table 7, changed Buffer type for PCI Express from CML to PCIe differential and changed reference clocks to HCSL. January 20, 2011: Added new Table 24, Signal Trace Length. March 30, 2011: In Table 12, added VddPETA to footnote #1. February 13, 2013: In Table 7, changed P01MERGEN and P23MERGEN pins from pull-down to pull-up. April 30, 2013: In Table 4, changed description for PxxMERGEN pins to pull-up via 92K ohm resistor. May 23, 2013: In the Features section, added reference to SECDED ECC under Reliability, Availability, Serviceability bullet. 31 of 32 May 23, 2013 IDT 89HPES16T4AG2 Data Sheet Ordering Information NN A AAA Product Family Operating Voltage Device Family NNANA Product Detail AN AA AA Generation Device Revision Series Legend A = Alpha Character N = Numeric Character A Package Temp Range Blank I Commercial Temperature (0C to +70C Ambient) Industrial Temperature (-40 C to +85 C Ambient) AL 324-ball FCBGA ALG 324-ball FCBGA, Green ZC ZC revision G2 PCIe Gen 2 16T4A 16-lane, 4-port PES PCI Express Switch H 1.0V +/- 0.1V Core Voltage 89 Serial Switching Product Valid Combinations 89HPES16T4AG2ZCAL 324-ball FCBGA package, Commercial Temperature 89HPES16T4AG2ZCALG 324-ball Green FCBGA package, Commercial Temperature 89HPES16T4AG2ZCALI 324-ball FCBGA package, Industrial Temperature 89HPES16T4AG2ZCALGI 324-ball Green FCBGA package, Industrial Temperature (R) CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 32 of 32 for Tech Support: email: ssdhelp@idt.com phone: 408-284-8208 May 23, 2013