Manual Switches Lamps, Soldering Recommendations, Receptacles AML91 LAMP ORDER GUIDE Lamp Type Industry Lamp No. Catalog Listing Incandescent T-1-3/4 wedge base 86 6.3 AML91LA86 73 14.0 AML91LA73 85 28.0 AML91LA85 Voltage LAMP DATA The following data was compiled from manufacturer's specifications, for reference only. SOLDERING RECOMMENDATIONS All terminals are solder plated. Proper soldering and cleaning procedures must be followed to maintain the reliability of AML products during installation. An instruction sheet which outlines these procedures is included with AML shipments. You may also obtain a copy from your MICRO SWITCH Sales Office. Request PK 8518. As a general guide, the following information may be used: INCANDESCENT LAMPS Industry Lamp No. AML91 Series Volts Amps Watts MSCP Life A/C Volts 86 6.3 5.5 5.0 .200 .185 .177 1.25 1.12 .89 .49 .246 .185 20,000 hours 106,200 hours 290,000 hours 73 14.0 12.0 .080 .077 1.12 1.00 .30 .23 15,000 hours 36,450 hours 85 28.0 24.0 .04 .037 1.12 .89 .30 .177 7,000 hours 41,860 hours Use a 280C (538F) solder iron tip, up to 6 seconds duration, with a 60-40 rosin core solder. This allows the terminal to heat quickly on the exterior of the housing only, and greatly reduces the chance of flux migrating inside the housing. Neon Lamps 25,000 hours (half life) INTEGRAL LEDs LEDs Furnished Permanently Installed in These Products Peak Inverse Voltage w/o Diode w/Diode Protection Protection Vf If VPD AML12, 15, 16, 22, 25, 26, 42 2.4 V 20 mA .7 V 5V 34 V AML45 2.4 V 20 mA .7 V 4V 33 V 100,000 hours (half life). LED APPLICATION INFORMATION For those devices without internal current limiting resistors, suitable external control of the LED current must be provided. It is recommended that a minimum of 5 VDC open circuit voltage with an appropriate series resistance be used to drive LED devices. This minimizes the effect of temperature (current variation) on forward voltage of the LED. Resistor values can be determined by supply voltage or current for LED: AML92 SERIES LEDs RS J For use with these AML switches and indicators equipped with lamp sockets: Pushbutton switches: AML11 (Square Only)*, AML21 (rectangular and square), and AML31. Paddle switches: AML31/23/33 Rocker switches: AML14/24/34 Indicators: AML41 * Rectangular solid state with one or two lamp circuits cannot be used with LED catalog listings ending in ``L''. E - Vf If AML92 ORDER GUIDE Quad Chip Six Chip Red LED Color AML92ERY AML92ERL Green AML92EGY AML92EGL Yellow AML92EYY AML92EYL White -- AML92EWL** ** For use with white or yellow buttons. OPERATING CHARACTERISTICS WHERE: RS J Series Resistance E J Supply Voltage Vf J Forward Voltage of LED If J Circuit Current If a diode is added in series for reverse polarity protection then: RS J Type VF Fwd. Voltage (typ.) Yellow Green Red White IF Fwd. Current VR Rev. Voltage Quad Chip 8.6 8.6 7.8 -- 15 mA 16 V Six Chip 4V 4V 4V 4V 50 mA 5.6 V E - Vf - VPD If WHERE: VPD Forward Voltage of Protection Diode TEMPERATURE RANGE (Quad Chip or Six Chip) Operating: -20 to 60C (-4 to 140F) Storage: -30 to 100C (-22 to 212F) 58 Honeywell 1 Sensing and Control 1 1-800-537-6945 USA 1 F1-815-235-6847 International 1 1-800-737-3360 Canada