Product Specification RoHS-6 Compliant Industrial Temperature 10Gb/s 10km XFP Optical Transceiver FTLX1413M3BTL PRODUCT FEATURES Supports 8.5Gb/s to 11.3Gb/s bit rates Power dissipation <1.5W Extended temperature range: -40C to 85C RoHS-6 Compliant (lead-free) Hot-pluggable XFP footprint Single Power supply: 3.3V APPLICATIONS SONET/SDH OC-192 SR-1 ITU G.693, VSR2000-2R1 Maximum link length of 10km 10GBASE-LR /LW 10G Ethernet Uncooled 1310nm DFB laser No Reference Clock required 1200-SM-LL-L 10G Fibre Channel and 800-SM-LC-L 8G Fibre Channel Built-in digital diagnostic functions ITU G.709 OTN/FEC OTU1e, OTU2, OTU2e 10G CPRI Finisar's FTLX1413M3BTL Industrial Temperature Small Form Factor 10Gb/s (XFP) transceivers are compliant with the current XFP Multi-Source Agreement (MSA) Specification1. They are a true multi-protocol transceiver complying with SONET OC192 SR-1, SDH STM I-64.1, 10-Gigabit Ethernet 10GBASE-LR /LW per IEEE 802.3ae, 10G Fibre Channel 1200-SM-LL-L, 8G Fibre Channel 800-SM-LC-L, 10G CPRI, and ITU-T. G709 OTN/FEC protocols OTU1e, OTU2, and OTU2e. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the XFP MSA. The optical transceiver is compliant per the RoHS Directive 2011/65/EU3. See Finisar Application Note AN-2038 for more details4. PRODUCT SELECTION FTLX1413M3BTL Finisar Corporation - April 2016 Rev B1 Page 1 FTLX1413M3BTL Product Specification I. Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 29 30 CML-O CML-O CML-I CML-I GND GND TDTD+ GND Name/Description Module Ground Optional -5.2 Power Supply - Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply- Not required Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply - Not required Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply - Not required Module Ground Reference Clock non-inverted input, AC coupled on the host board - Not required Reference Clock inverted input, AC coupled on the host board - Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 3 3 1 1 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k - 10kohms on host board to a voltage between 3.15V and 3.6V. 3. A Reference Clock input is not required by the FTLX1413M3BTL. If present, it will be ignored. Finisar Corporation - April 2016 Rev B1 Page 2 FTLX1413M3BTL Product Specification Diagram of Host Board Connector Block Pin Numbers and Name II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Finisar Corporation - April 2016 Symbol Vcc3 TS TOP Min -0.5 -40 -40 Rev B1 Typ Max 3.6 85 85 Unit V C C Ref. Page 3 FTLX1413M3BTL Product Specification III. Electrical Characteristics (TOP = -40 to 85 C, VCC3 = 3.13 to 3.45 Volts) Parameter Supply Voltage Supply Current Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc3 Icc3 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 3.13 Typ Max 3.45 600 1.5 100 120 2.0 GND 340 Vcc - 0.5 GND 820 Vcc GND+ 0.8 10 650 850 38 38 VccHOST GND+0.5 See Note 8 below Unit V mA W mV V V us mV ps ps V V Ref. 1 2 3 4 5 6 6 7 7 8 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. SONET/SDH jitter generation requirements are guaranteed with a minimum differential data input swing of 500mV peak-to-peak. 4. Or open circuit. 5. Into 100 ohms differential termination. 6. 20 - 80 % 7. Loss Of Signal is open collector to be pulled up with a 4.7k - 10kohm resistor to 3.15 - 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 8. Per Section 2.7.1. in the XFP MSA Specification1. Finisar Corporation - April 2016 Rev B1 Page 4 FTLX1413M3BTL Product Specification IV. Optical Characteristics (TOP = -40 to 85C, VCC3 = 3.13 to 3.45 Volts) Parameter Transmitter Output Opt. Pwr:9/125 SMF Optical Wavelength Optical Extinction Ratio Sidemode Supression ratio Tx Jitter (SONET/SDH) 20kHz-80MHz Tx Jitter (SONET/SDH) 4MHz - 80MHz Relative Intensity Noise Receiver Receiver Sensitivity @ 9.95Gb/s Receiver Sensitivity @ 10.5Gb/s Receiver Sensitivity @ 11.3Gb/s Stressed Receiver Sensitivity (OMA) @ 10.5Gb/s Maximum Input Power Optical Center Wavelength Receiver Reflectance LOS De-Assert LOS Assert LOS Hysteresis Symbol Min POUT ER SSRmin -6 1290 6 30 Typ Max -1 1330 Unit dBm nm dB dB Txj1 0.3 UI Txj2 0.1 UI RIN -130 RSENS1 RSENS2 RSENS3 RSENS4 -14.4 -14.4 -13.4 -10.3 dB/Hz dBm dBm dBm dBm PMAX C Rrx LOSD LOSA +0.5 1260 -32 0.5 1600 -14 -18 Ref. 1 1 2 2 3 dBm nm dB dBm dBm dB Notes: 1. Having ER = 6 dB guarantees that the -6 dBm minimum output power meets IEEE 802.3ae requirement of OMA=-5.2dBm. 2. Measured with worst ER; BER<10-12; 231 - 1 PRBS. Complies with -12.6 dBm OMA at ER = 6 dB. 3. Per IEEE 802.3ae. Equivalent to -13.3 dBm average power at Infinite ER, -11.08 dBm at ER = 6 dB. 8.5Gb/s Fibre-Channel: To operate the FTLX1413M3BTL at 8.5Gb/s Fibre-Channel, the EEPROM-Table 0, Byte 117, Bit 0 must be set as follows; . EEPROM Byte 117, Bit 0, value "1" for 8GFC: EEPROM Byte 117, Bit 0 value "0" for 10Gb/s rates: o (It is also possible to bypass the CDRs with, Byte 111, Bit 0.) By default, a power cycling the transceiver will return the transceiver to normal 10Gb/s operation with the CDRs active. Finisar Corporation - April 2016 Rev B1 Page 5 FTLX1413M3BTL Product Specification V. General Specifications Parameter Bit Rate Bit Error Ratio Max. Supported Link Length Symbol BR BER LMAX Min 8.5 Typ Max 11.3 10-12 10 Units Gb/s km Ref. 1 2 1 Notes: 1. SONET OC-192 SR-1, SDH STM I-64.1, 10GBASE-LR/LW, 1200-SM-LL-L, 800-SM-LC-L, SONET OC-192 with FEC, 10GBASE-LR/LW with FEC, 1200-SM-LL-L with FEC. 2. Tested with a 231 - 1 PRBS VI. Environmental Specifications Finisar FTLX1413M3BTL transceivers have an inductrial operating case temperature range of -40C to +85C. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -40 -40 Typ Max 85 85 Units C C Ref. Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TUV R72101686 Electrical Safety Electrical Safety TUV EN 60825-1: 2007, EN60825-2:2004+A1 IEC 60825-1: 2007 (2nd Edition) IEC 60825-2: 2010 (3rd Edition) EN 60950:2006+A11 CLASS 3862.07 CLASS 3862.87 2283290 UL/CSA Certificate Number 9210176-77 R72101686 Copies of the referenced certificates are available at Finisar Corporation upon request. Finisar Corporation - April 2016 Rev B1 Page 6 FTLX1413M3BTL Product Specification VIII. Digital Diagnostic Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information including memory map definitions, please see Finisar Application Note AN-2035 "Digital Diagnostic Monitoring Interface for XFP Optical Transceivers", or the XFP MSA Specification1. Finisar Corporation - April 2016 Rev B1 Page 7 FTLX1413M3BTL Product Specification IX. Mechanical Specifications Finisar's XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA). XFP Transceiver (dimensions are in mm) Finisar Corporation - April 2016 Rev B1 Page 8 FTLX1413M3BTL Product Specification X. PCB Layout and Bezel Recommendations XFP Host Board Mechanical Layout (dimensions are in mm) Finisar Corporation - April 2016 Rev B1 Page 9 FTLX1413M3BTL Product Specification XFP Detail Host Board Mechanical Layout (dimensions are in mm) XFP Recommended Bezel Design (dimensions are in mm) Finisar Corporation - April 2016 Rev B1 Page 10 FTLX1413M3BTL Product Specification XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 - August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: "Digital Diagnostic Monitoring Interface for XFP Optical Transceivers" - Finisar Corporation, December 2003 3. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment" 4. "Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers" XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation - April 2016 Rev B1 Page 11