10011-10 - Vishay Presicion Group

DSCC 10011

www.vishay.com Vishay

Revision: 15-Mar-12 1Document Number: 40141

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Wet Tantalum Capacitors, Tantalum-Case with Glass-to-Tantalum

Hermetic Seal for - 55 °C to + 125 °C Operation

FEATURES

• High energy, very high capacitance design

• All tantalum, hermetically sealed case

• Utilizes Vishay proven SuperTan® technology

• Terminations: Radial leaded

• Approved to DSCC drawing 10011

PERFORMANCE CHARACTERISTICS

Operating Temperature:

- 55 °C to + 85 °C (to + 125 °C with voltage derating)

Capacitance Tolerance:

At 120 Hz, + 25 °C ± 20 % standard

DC Leakage Current (DCL Max.):

At + 25 °C: Leakage current shall not exceed the values

listed in the Standard Ratings tables.

Life Test:

Capacitors are capable of withstanding a 1000 h life test at

a temperature of + 85 °C at the applicable rated DC working

voltage.

ORDERING INFORMATION

10011 -01

DSCC DRAWING NUMBER DASH NUMBER

DEFENSE SUPPLY CENTER, COLUMBUS

COLUMBUS, OHIO

DRAWING NUMBER

10011

DIMENSIONS in inches [millimeters]

CASE CODE

DHEIGHT L2

(MIN.)

(MIN.) T

WEIGHT

(g)

(TYPICAL)

TYPE DSCC 10011

A1.400 ± 0.005

[35.56 ± 0.127]

0.350 ± 0.015

[8.89 ± 0.381]

0.500

[12.70]

0.500

[12.70]

0.40 ± 0.015

[10.2 ± 0.38] 48.0

B1.400 ± 0.005

[35.56 ± 0.127]

0.488 ± 0.015

[15.60 ± 0.381]

0.500

[12.70]

0.500

[12.70]

0.40 ± 0.015

[10.2 ± 0.38] 73.0

C1.400 ± 0.005

[35.56 ± 0.127]

0.615 ± 0.015

[15.6 ± 0.4]

0.500

[12.70]

0.500

[12.70]

0.40 ± 0.015

[10.2 ± 0.38] 95.0

Positive lead

0.0253 ± 0.002 [0.64 ± 0.05] Dia.

(No. 22 AWG) Tinned Nickel leads

solderable and weldable

Negative lead

(attached to case)

0.156 MAX..

DSCC 10011

www.vishay.com Vishay

Revision: 15-Mar-12 2Document Number: 40141

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PERFORMANCE CHARACTERISTICS OF HIGH ENERGY CAPACITORS

STANDARD RATINGS

CAPACITANCE

(μF) CASE CODE

MAX. ESR

AT + 25 °C

MAX. 1 kHz

()

MAX. DCL

AT + 25 °C

(μA)

PART NUMBER

25 VDC AT + 85 ºC; 15 VDC AT + 125 °C

24 000 A 0.060 150 10011-05

18 000 A 0.060 150 10011-06

48 000 B 0.045 200 10011-03

36 000 B 0.045 200 10011-04

72 000 C 0.035 350 10011-01

54 000 C 0.035 300 10011-02

50 VDC AT + 85 ºC; 30 VDC AT + 125 °C

8000 A 0.060 170 10011-09

16 000 B 0.045 270 10011-08

24 000 C 0.035 400 10011-07

63 VDC AT + 85 ºC; 40 VDC AT + 125 ºC

4000 A 0.060 170 10011-12

8000 B 0.045 270 10011-11

12 000 C 0.035 400 10011-10

80 VDC AT + 85 ºC; 50 VDC AT + 125 ºC

3000 A 0.075 300 10011-16

6000 B 0.060 400 10011-15

9000 C 0.040 500 10011-13

100 VDC AT + 85 ºC; 65 VDC AT + 125 ºC

1900 A (1) 0.075 300 10011-

3800 B (1) 0.06 400 10011-

5700 C (1) 0.05 500 10011-

125 VDC AT + 85 ºC; 85 VDC AT + 125 ºC

1100 A (1) 0.100 300 10011-

2200 B (1) 0.085 400 10011-

3300 C (1) 0.075 500 10011-

Note

(1) Preliminary rating and electrical values. Contact marketing for availability.

ELECTRICAL PERFORMANCE CHARACTERISTICS

ITEM PERFORMANCE CHARACTERISTICS

Operating temperature range - 55 °C to + 85 °C (to + 125 °C with voltage derating)

Capacitor tolerance ± 20 % at 120 Hz

ESR Limits per Standard Ratings table

DC leakage current (DCL max.) At 25 °C the leakage current shall not exceed values listed in the Standard Rating table.

Reverse voltage No continuous reverse voltage permitted

Surge voltage The test shall be at 1000 cycles at 110 % of rated voltage at 85 °C. A cycle consists of a 30 s

charge and a 330 s discharge through 100  resistor.

Life test at + 85 °C 1000 h at + 85 °C

DSCC 10011

www.vishay.com Vishay

Revision: 15-Mar-12 3Document Number: 40141

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DSCC 10011 MOUNTING OPTIONS

The DSCC 10011 capacitor can be mounted with many commercially available methods. Vishay offers the optional mounting

hardware outlined below.

THROUGH-HOLE

If mounted through-hole, the glass-to-metal seal must be protected from potential mounting and application stress. The HE3

can be mounted termination down through the HE3 SPC001 spacer into the PCB. The proper size bracket HE3BKT00* can then

be utilized to hold the DSCC 10011 rigidly to the PCB.

TERMINATIONS UP

If mounted with terminations facing up for attachment to wiring, the spacer is not needed. The DSCC 10011 can be reverse with

terminations facing upward through the center of the HE3BKT00* bracket, which is then mounted through the PCB.

ENVIRONMENTAL CHARACTERISTICS

ITEM TEST AND CONDITIONS COMMENTS

Hermeticity MIL-STD-202, method 112 C/IIIa The capacitor shall be hermetically sealed such that the case does not

leak electrolyte or vent any gas when exposed to a vacuum.

Moisture resistance MIL-STD-202, method 106 6 V polarity

Altitude MIL-STD-202, method 105 C,

test condition D 100 000 feet test

MECHANICAL PERFORMANCE CHARACTERISTICS

ITEM TEST AND CONDITIONS COMMENTS

Thermal shock MIL-STD-202, method 107 G Test condition A

Shock MIL-STD-202, method 213 B

test condition G 11 ms, 50 g

Vibration - high frequency MIL-STD-202, method 204 D

test condition D 12 sweeps/axis, 20 g peak

Vibration - random MIL-STD-202, method 214 A

test condition I, Letter D 1.5 h/axis, 12 g

Resistance to solder heat MIL-STD-202, method 210 F

The capacitor must withstand solder dipping of the terminals at 260 °C

for 10 s. The capacitor must not be visibly damaged and the electrical

characteristics must not be affected.

Solderability MIL-STD-202, method 208

Terminal strength MIL-STD-202, method 211 A

The capacitor terminals must withstand a 5 pound pull test for 5 s to 10 s.

The capacitor must not be visibly damaged and the electrical

characteristics must not be affected.

Resistance to solvents MIL-STD-202, method 215 J The capacitor shall be permanently and legibly marked on the

circumference of the case. The markings shall be resistant to solvents.

Weight (mass) See dimensions table

DSCC 10011

www.vishay.com Vishay

Revision: 15-Mar-12 4Document Number: 40141

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

• Spot weld, 2 places

• Mounting bolt:

1. Material - Stainless steel

2. Thread - 6-32 NC-2A

Note

(1) The part numbers shown are for ordering the mounting bracket and/or spacer. The DSCC 10011 capacitor must be ordered separately using

the correct part number as outlined in Ordering Information and in the Standard Ratings table.

Note

(1) The part numbers shown are for ordering the mounting bracket and/or spacer. The HE3 capacitor must be ordered separately using the

correct part number as outlined in Ordering Information and in the Standard Ratings table.

PART NUMBER (1) STUD A ± 0.010

HE3BKT001 HE3A 0.391

HE3BKT002 HE3B 0.518

HE3BKT003 HE3C 0.605

HE3BKT004 HE3A W/spacer 0.572

HE3BKT005 HE3B W/spacer 0.699

HE3BKT006 HE3C W/spacer 0.831

PART NUMBER (1)

HE3SPC001

HE3 Nickel hold down cup

MS-HE-04-003

HE Hold down stud

MS-C-17-315-1

0.789 1.579

1.150 Dia.

1.326 ± 0.002 Dia.

1.400 Dia.

0.195

0.015

Note

Mat. L: Aluminum

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 12-Mar-12 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical

requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements

about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular

product with the properties described in the product specification is suitable for use in a particular application. Parameters

provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All

operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree

to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and

damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay

or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to

obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by

any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the

definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council

of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that

all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.