LM6588 LM6588 TFT-LCD Quad, 16V RRIO High Output Current Operational Amplifier Literature Number: SNOSA77C LM6588 TFT-LCD Quad, 16V RRIO High Output Current Operational Amplifier General Description Features The LM6588 is a low power, high voltage, rail-to-rail inputoutput amplifier ideally suited for LCD panel VCOM driver and gamma buffer applications. The LM6588 contains four unity gain stable amplifiers in one package. It provides a common mode input ability of 0.5V beyond the supply rails, as well as an output voltage range that extends to within 50mV of either supply rail. With these capabilities, the LM6588 provides maximum dynamic range at any supply voltage. Operating on supplies ranging from 5V to 16V, while consuming only 750A per amplifier, the LM6588 has a bandwidth of 24MHz (-3dB). The LM6588 also features fast slewing and settling times, along with a high continuous output capability of 75mA. This output stage is capable of delivering approximately 200mA peak currents in order to charge or discharge capacitive loads. These features are ideal for use in TFT-LCDs. The LM6588 is available in the industry standard 14-pin SO package and in the space-saving 14-pin TSSOP package. The amplifiers are specified for operation over the full -40C to +85C temperature range. (VS = 5V, TA = 25C typical values unless specified) n Input common mode voltage 0.5V beyond rails n Output voltage swing (RL = 2k) 50mV from rails 200mA n Output short circuit current n Continuous output current 75mA n Supply current (per amp, no load) 750A n Supply voltage range 5V to 16V n Unity gain stable n -3dB bandwidth (AV = +1) 24MHz n Slew rate 11V/Sec n Settling time 270ns n SO-14 and TSSOP-14 package n Manufactured in National Semiconductor's state-of-the-art bonded wafer, trench isolated complementary bipolar VIP10TM technology for high performance at low power levels Applications n LCD panel VCOM driver n LCD panel gamma buffer n LCD panel repair amp Test Circuit Diagram 20073401 (c) 2005 National Semiconductor Corporation DS200734 www.national.com LM6588 TFT-LCD Quad, 16V RRIO High Output Current Operational Amplifier July 2005 LM6588 Absolute Maximum Ratings (Note 1) Input Common Mode Voltage If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Junction Temperature (Note 4) Temperature Range 250V + - Supply Voltage (V - V ) 18V Differential Input Voltage 5.5V Output Short Circuit to Ground (Note 3) Storage Temperature Range 4V VS 16V Supply Voltage 2.5KV Machine Model 150C Operating Ratings (Note 1) ESD Tolerance (Note 2) Human Body Model V- to V+ -40C to +85C Thermal Resistance (JA) Continuous SOIC-14 145C/W TSSOP-14 155C/W -65C to 150C 16V DC Electrical Characteristics (Note 13) Unless otherwise specified, all limits guaranteed for at TJ = 25C, VCM = 12VS and RL = 2k. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TC VOS Input Offset Voltage Average Drift IB Input Bias Current IOS Input Offset Current RIN Input Resistance CMRR Common Mode Rejection Ratio Conditions Min (Note 6) Typ (Note 5) Max (Note 6) 0.7 4 6 5 1 7 16 150 300 20 Differential Mode 0.5 VCM = 0 to +16V 75 70 103 VCM = 0 to 14.5V 78 72 103 80 75 103 PSRR Power Supply Rejection Ratio VCM = 1V CMVR Input Common-Mode Voltage Range CMRR > 50dB AV Large Signal Voltage Gain (Note 7) RL = 2k, VO = 0.5 to +15.5V VO Output Swing High RL = 2k Output Swing Low RL = 2k Output Short Circuit Current (Note 11) Sourcing 170 230 Sinking 170 230 Continuous Output Current (Note 12) Sourcing 40 Sinking 40 ISC ICONT IS 16.2 0 16 80 75 108 15.8 15.6 15.9 A nA M dB dB -0.2 V dB V 0.100 Supply Current (per Amp) mV V/C -0.3/+0.3 Common Mode Units 800 0.200 mA mA 1200 1500 A 16V AC Electrical Characteristics (Note 13) Unless otherwise specified, all limits guaranteed for at TJ = 25C, VCM = 12VS and RL = 2k. Boldface limits apply at the temperature extremes. Symbol SR Parameter Slew Rate (Note 9) www.national.com Conditions AV = +1, VIN = 10VPP 2 Min (Note 6) Typ (Note 5) 8 15 Max (Note 6) Units V/s (Note 13) (Continued) Unless otherwise specified, all limits guaranteed for at TJ = 25C, VCM = 12VS and RL = 2k. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 6) Unity Gain Bandwidth Product -3dB Frequency AV = +1 10 m Phase Margin ts Settling Time (0.1%) AV = -1, AO = 5V, RL = 500 Typ (Note 5) Max (Note 6) Units 15.4 MHz 24 MHz 61 deg 780 ns tp Propagation Delay AV = -2, VIN = 5V, RL = 500 20 ns HD2 2nd Harmonic Distortion FIN = 1MHz (Note 10) VOUT = 2VPP -53 dBc HD3 3rd Harmonic Distortion FIN = 1MHz (Note 10) VOUT = 2VPP -40 dBc en Input-Referred Voltage Noise f = 10kHz 23 nV/ 5V DC Electrical Characteristics (Note 13) Unless otherwise specified, all limits guaranteed for at TJ = 25C, VCM = 12VS and RL = 2k. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 6) Typ (Note 5) Max (Note 6) 4 6 VOS Input Offset Voltage 0.7 TC VOS Input Offset Voltage Average Drift 10 IB Input Bias Current IOS Input Offset Current RIN Input Resistance CMRR Common Mode Rejection Ratio A 20 150 300 nA 20 Differential Mode 0.5 VCM Stepped from 0 to 5V 70 66 105 VCM Stepped from 0 to 3.5V 75 70 105 80 75 92 Power Supply Rejection Ratio VS = VCC = 3.5V to 5.5V CMVR Input Common-Mode Voltage Range CMRR > 50dB AV Large Signal Voltage Gain (Note 7) RL = 2k, VO = 0 to 5V VO Output Swing High RL = 2k Output Swing Low RL = 2k Output Short Circuit Current (Note 11) Sourcing 160 200 Sinking 160 200 Continuous Output Current (Note 12) Sourcing 75 Sinking 75 ICONT IS 0.0 5.0 80 75 106 4.85 4.7 4.95 750 3 M dB dB -0.2 V dB V 0.05 Supply Current (per Amp) V/C 1 7 PSRR ISC mV -0.3/+0.3 Common Mode 5.2 Units 0.15 mA mA 1000 1250 A www.national.com LM6588 16V AC Electrical Characteristics LM6588 5V AC Electrical Characteristics (Note 13) Unless otherwise specified, all limits guaranteed for at TJ = 25C, VCM = 12VS and RL = 2k. Boldface limits apply at the temperature extremes. Symbol SR Parameter Slew Rate (Note 9) Conditions Min (Note 6) Typ (Note 5) AV = +1, VIN = 3.5VPP Unity Gain Bandwidth Product -3dB Frequency AV = +1 10 Max (Note 6) Units 11 V/s 15.3 MHz 24 MHz 56 deg m Phase Margin ts Settling Time (0.1%) AV = -1, VO = 1V, RL = 500 270 ns tp Propagation Delay AV = -2, VIN = 1V, RL = 500 21 ns HD2 2nd Harmonic Distortion FIN = 1MHz (Note 10) VOUT = 2VPP -53 dBc HD3 3rd Harmonic Distortion FIN = 1MHz (Note 10) VOUT = 2VPP -40 dBc en Input-Referred Voltage Noise f = 10kHz 23 nV/ Note 1: Note 1: Absolute maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: For testing purposes, ESD was applied using human body model, 1.5k in series with 100pF. Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C Note 4: The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ JA . All numbers apply for packages soldered directly onto a PC board. Note 5: Typical values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: Large signal voltage gain is the total output swing divided by the input signal required to produce that swing. Note 8: The open loop output current is guaranteed, by the measurement of the open loop output voltage swing. Note 9: Slew rate is the average of the raising and falling slew rates. Note 10: Harmonics are measured with AV = +2 and RL = 100 and VIN = 1VPP to give VOUT = 2VPP. Note 11: Continuous operation at these output currents will exceed the power dissipation ability of the device Note 12: Power dissipation limits may be exceeded if all four amplifiers source or sink 40mA. Voltage across the output transistors and their output currents must be taken into account to determine the power dissipation of the device Note 13: Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where TJ > TA. See applications section for information on temperature de-rating of this device. Connection Diagram 14-Pin SOIC/TSSOP 20073402 Top View Ordering Information Package 14-Pin SOIC 14-Pin TSSOP www.national.com Part Number LM6588MA LM6588MAX LM6588MT LM6588MTX Package Marking Transport Media 95 Units/Rail LM6588MA 2.5k Units Tape and Reel 95 Units/Rail LM6588MT 2.5k Units Tape and Reel 4 NSC Drawing M14A MTC14 Unless otherwise specified, all limits guaranteed for TJ = 25C, Gain Phase vs. Temperature (VS = 5V) Gain Phase vs. Temperature (VS = 16V) 20073403 20073404 Gain Phase vs. Capacitive Loading (VS = 5V) Gain Phase vs. Capacitive Loading (VS = 16V) 20073406 20073405 PSRR (VS = 5V) PSRR (VS = 16V) 20073407 20073408 5 www.national.com LM6588 Typical Performance Characteristics VCM = 1/2VS and RL = 2k. LM6588 Typical Performance Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = 1/2VS and RL = 2k. (Continued) CMRR (VS = 5V) CMRR (VS = 16V) 20073409 20073410 Settling Time vs. Input Step Amplitude (Output Slew and Settle Time) Settling Time vs. Capacitive Loading (Output Slew and Settle Time) 20073412 20073411 Crosstalk Rejection vs. Frequency (Output to Output) Input Voltage Noise vs. Frequency 20073413 www.national.com 20073414 6 Stability vs. Capacitive Load Unity Gain (VS = 16V) Large Signal Step Response 20073416 20073415 Small Signal Step Response Small Signal Step Response 20073417 20073418 ISUPPLY vs. Common Mode Voltage (VS = 5V) Closed Loop Output Impedance vs. Frequency (AV = +1) 20073420 20073419 7 www.national.com LM6588 Typical Performance Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = 1/2VS and RL = 2k. (Continued) LM6588 Typical Performance Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = 1/2VS and RL = 2k. (Continued) VOS vs. Common Mode Voltage (VS = 16V) VOS vs. VOUT (Typical Unit), (VS = 10V) 20073421 20073422 + - VOUT from V vs. ISOURCE VOUT from V vs. ISINK 20073423 20073424 ISUPPLY vs. Supply Voltage 20073425 www.national.com 8 Output Power CIRCUIT DESCRIPTION GENERAL & SPEC Because of the increased output drive capability, internal heat dissipation must be held to a level that does not increase the junction temperature above its maximum rated value of 150 C. The LM6588 is a bipolar process operational amplifier. It has an exceptional output current capability of 200mA. The part has both rail to rail inputs and outputs. It has a -3dB bandwidth of 24MHz. The part has input voltage noise of 23nV/ , and 2nd and 3rd harmonic distortion of -53dB and -40dB respectively. Power Requirements The LM6588 operates from a voltage supply, of V+ and ground, or from a V- and V+ split supply. Single-ended voltage range is +5V to +16V and split supply range is 2.5V to 8.0V. INPUT SECTION The LM6588 has rail to rail inputs and thus has an input range over which the device may be biased of V- minus 0.5V, and V+ plus 0.5V. The ultimate limit on input voltage excursion is the ESD protection diodes on the input pins. The most important consideration in Rail-to-Rail input op amps is to understand the input structure. Most Rail-to-Rail input amps use two differential input pairs to achieve this function. This is how the LM6588 works. A conventional PNP differential transistor pair provides the input gain from 0.5V below the negative rail to about one volt below the positive rail. At this point internal circuitry activates a differential NPN transistor pair that allows the part to function from 1 volt below the positive rail to 0.5V above the positive rail. The effect on the inputs pins is as if there were two different op amps connected to the inputs. This has several unique implications. * The input offset voltage will change, sometimes from positive to negative as the inputs transition between the two stages at about a volt below the positive rail. this effect is seen in the VOS vs. VCM chart in the Typical Performance Characteristics section of this datasheet. * The input bias currents can be either positive or negative. Do not expect a consistent flow in or out of the pins. * The part will have different specifications depending on whether the NPN or PNP stage is operating. * There is a little more input capacitance then a single stage input although the ESD diodes often swamp out the added base capacitance. * Since the input offset voltages can change from positive to negative the output may not be monotonic when the inputs are transitioning between the two stages and the part is in a high gain configuration. It should be remembered that swinging the inputs across the input stage transition may cause output distortion and accuracy anomalies. It is also worth noting that anytime any amps inputs are swung near the rails THD and other specs are sure to suffer. APPLICATION HINTS POWER SUPPLIES Sequencing Best practice design technique for operational amplifiers includes careful attention to power sequencing. Although the LM6588 is a bipolar op amp, recommended op amp turn on power sequencing of ground (or V-), followed by V+, followed by input signal should be observed. Turn off power sequence should be the reverse of the turn-on sequence. Depending on how the amp is biased the outputs may swing to the rails on power-on or power-off. Due to the high output currents and rail to rail output stage in the LM6588 the output may oscillate very slightly if the power is slowly raised between 2V and 4V The part is unconditionally stable at 5V. Quick turn-off and turn-on times will eliminate oscillation problems. PSRR and Noise Care should be taken to minimize the noise in the power supply rails. The figure of merit for an op amp's ability to keep power supply noise out of the signal is called Power Supply Rejection Ratio (PSRR). Observe from the PSRR charts in the Typical Performance Characteristics section that the PSRR falls of dramatically as the frequency of the noise on the power supply line goes up. This is one of the reasons switching power supplies can cause problems. It should also be noticed from the charts that the negative supply pin is far more susceptible to power noise. The design engineer should determine the switching frequencies and ripple voltages of the power supplies in the system. If required, a series resistor or in the case of a high current op amp like the LM6588, a series inductor can be used to filter out the noise. Transients In addition to the ripple and noise on the power supplies there are also transient voltage changes. This can be caused by another device on the same power supply suddenly drawing current or suddenly stopping a current draw. The design engineer should insure that there are no damaging transients induced on the power supply lines when the op amp suddenly changes current delivery. OUTPUT SECTION Current Rating The LM6588 has an output current rating, sinking or sourcing, of 200mA. The LM6588 is ideally suited to loads that require a high value of peak current but only a reduced value of average current. This condition is typical of driving the gate of a MOSFET. While the output drive rating is 200mA peak, and the output structure supports rail-to-rail operation, the attainable output current is reduced when the gain and drive conditions are such that the output voltage approaches either rail. LAYOUT Ground Planes Do not assume the ground (or more properly, the common or return) of the power supply is an ocean of zero impedance. The thinner the trace, the higher the resistance. Thin traces cause tiny inductances in the power lines. These can react against the large currents the LM6588 is capable of delivering to cause oscillations, instability, overshoot and distortion. A ground plane is the most effective way of insuring the 9 www.national.com LM6588 Application Notes LM6588 Application Notes driven to the rail and the part can no longer maintain the feedback loop, the internal circuitry will deliver large base currents into the huge output transistors, trying to get the outputs to get past the saturation voltage. The base currents will approach 16 milliamperes and this will appear as an increase in power supply current. Operating at this power dissipation level for extended periods will damage the part, especially in the higher thermal resistance TSSOP package. Because of this phenomenon, unused parts should not have the inputs strapped to either rail, but should have the inputs biased at the midpoint or at least a diode drop (0.6V) within the rails. (Continued) ground is a uniform low impedance. If a four layer board cannot be used, consider pouring a plane on one side of a two layer board. If this cannot be done be sure to use as wide a trace as practicable and use extra decoupling capacitors to minimize the AC variations on the ground rail. Decoupling A high-speed, high-current amp like the LM6588 must have generous decoupling capacitors. They should be as close to the power pins as possible. Putting them on the back side opposite the power pins may give the tightest layout. If ground and power planes are available, the placement of the decoupling caps are not as critical. Self Heating As discussed above the LM6588 is capable of significant power by virtue of its 200mA current handling capability. A TSSOP package cannot sustain these power levels for more then a brief period. Breadboards The high currents and high frequencies the LM6588 operates at, as well as thermal considerations, require that prototyping of the design be done on a circuit board as opposed to a "Proto-Board" style breadboard. TFT Display Application INTRODUCTION In today's high-resolution TFT displays, op amps are used for the following three functions: 1. VCOM Driver 2. Gamma Buffer 3. Panel Repair Buffer All of these functions utilize op amps as non-inverting, unitygain buffers. The VCOM Driver and Gamma Buffer are buffers that supply a well regulated DC voltage. A Panel Repair Buffer, on the other hand, provides a high frequency signal that contains part of the display's visual image. STABILITY General: High speed parts with large output current capability require special care to insure lack of oscillations. Keep the "+" pin isolated from the output to insure stability. As noted above care should be take to insure the large output currents do not appear in the ground or ground plane and then get coupled into the "+" pin. As always, good tight layout is essential as is adequate use of decoupling capacitors on the power supplies. In an effort to reduce production costs, display manufacturers use a minimum variety of different parts in their TFT displays. As a result, the same type of op amp will be used for the VCOM Driver, Gamma Buffer, and Panel Repair Buffer. To perform all these functions, such an op amp must have the following characteristics: 1. Large output current drive 2. Rail to rail input common mode range 3. Rail to rail output swing 4. Medium speed gain bandwidth and slew rate The LM6588 meets these requirements. It has a rail-to-rail input and output, typical gain bandwidth and slew rate of 15MHz and 15V/s, and it can supply up to 200mA of output current. The following sections will describe the operation of VCOM Drivers, Gamma Buffers, and Panel Repair Buffers, showing how the LM6588 is well suited for each of these functions. Unity Gain The unity gain or voltage-follower configuration is the most subject to oscillation. If a part is stable at unity gain it is almost certain to work in other configurations. In certain applications where the part is setting a reference voltage or is being used as a buffer greater stability can be achieved by configuring the part as a gain of -1 or -2 or +2. Phase Margin The phase margin of an op amps gain-phase plot is an indication of the stability of the amp. It is desirable to have at least 45C of phase margin to insure stability in all cases. The LM6588 has 60C of phase margin even with it's large output currents and Rail-to-Rail output stage, which are generally more prone to stability issues. Capacitive Load The LM6588 can withstand 30pF of capacitive load in a unity gain configuration before stability issues arise. At very large capacitances, the load capacitor will attenuate the gain like any other heavy load and the part becomes stable again. The LM6588 will be stable at 330nF and higher load capacitance. Refer to the chart in the Typical Performance Characteristics section. BRIEF OVERVIEW OF TFT DISPLAY To better understand these op amp applications, let's first review a few basic concepts of how a TFT display operates. Figure 1 is a simplified illustration of an LCD pixel. The top and bottom plates of each pixel consist of Indium-Tin oxide (ITO), which is a transparent, electrically conductive material. ITO lies on the inner surfaces of two glass substrates that are the front and back glass panels of a TFT display. Sandwiched between the two ITO plates is an insulating material (liquid crystal) that alters the polarization of light to a lesser a greater amount, depending on how much voltage (VPIXEL) is applied across the two plates. Polarizers are placed on the outer surfaces of the two glass substrates, which in combination with the liquid crystal create a variable OUTPUT Swing vs. Current The LM6588 will get to about 25mV or 30mV of either rail when there is no load. The LM6588 can sink or source hundreds of milliamperes while remaining less then 0.5V away from the rail. It should be noted that if the outputs are www.national.com 10 the Column Drivers supply this voltage via the column lines. Column Drivers `write' this voltage to the pixels one row at a time, and this is accomplished by having the Row Drivers select an individual row of pixels when their voltage levels are transmitted by the Column Drivers. The Row Drivers sequentially apply a large positive pulse (typically 25V to 35V) to each row line. This turns-on NMOS transistors connected to an individual row, allowing voltages from the column lines to be transmitted to the pixels. (Continued) light filter that modulates light transmitted from the back to the front of a display. A pixel's bottom plate lies on the backside of a display where a light source is applied, and the top plate lies on the front, facing the viewer. On a Twisted Neumatic (TN) display, which is typical of most TFT displays, a pixel transmits the greatest amount of light when VPIXEL is less 0.5V, and it becomes less transparent as this voltage increases with either a positive or negative polarity. In short, an LCD pixel can be thought of as a capacitor, through which, a controlled amount of light is transmitted by varying VPIXEL. VCOM DRIVER The VCOM driver supplies a common voltage (VCOM) to all the pixels in a TFT panel. VCOM is a constant DC voltage that lies in the middle of the column drivers' output voltage range. As a result, when the column drivers write to a row of pixels, they apply voltages that are either positive or negative with respect to VCOM. In fact, the polarity of a pixel is reversed each time its row is selected. This allows the column drivers to apply an alternating voltage to the pixels rather than a DC signal, which can `burn' a pattern into an LCD display. When column drivers write to the pixels, current pulses are injected onto the VCOM line. These pulses result from charging stray capacitance between VCOM and the column lines (see Figure 2), which ranges typically from 16pF to 33pF per column. Pixel capacitance contributes very little to these pulses because only one pixel at a time is connected to a column, and the capacitance of a single pixel is on the order of only 0.5pF. Each column line has a significant amount of series resistance (typically 2k to 40k), so the stray capacitance is distributed along the entire length of a column. This can be modeled by the multi-segment RC network shown in Figure 3. The total capacitance between VCOM and the column lines can range from 25nF to 100nF, and charging this capacitance can result in positive or negative current pulses of 100mA, or more. In addition, a similar distributed capacitance of approximately the same value exists between VCOM and the row lines. Therefore, the VCOM driver's load is the sum of these distributed RC networks with a total capacitance of 50nF to 200nF, and this load can modeled like the circuit in Figure 3. 20073426 FIGURE 1. Individual LCD Pixel 20073428 FIGURE 3. Model of Impedance between VCOM and Column Lines 20073427 FIGURE 2. TFT Display A VCOM driver is essentially a voltage regulator that can source and sink current into a large capacitive load. To simplify the analysis of this driver, the distributed RC network of Figure 3 has been reduced to a single RC load in Figure 4. This load places a large capacitance on the VCOM driver output, resulting in an additional pole in the op amp's feedback loop. However, the op amp remains stable because CLOAD and RESR create a zero that cancels the effect of this pole. The range of CLOAD is 50nF to 200nF and RESR is 20 to 100, so this zero will have a frequency in the range of Figure 2 is a simplified block diagram of a TFT display, showing how individual pixels are connected to the row, column, and VCOM lines. Each pixel is represented by capacitor with an NMOS transistor connected to its top plate. Pixels in a TFT panel are arranged in rows and columns. Row lines are connected to the NMOS gates, and column lines to the NMOS sources. The back plate of every pixel is connected to a common voltage called VCOM. Pixel brightness is controlled by voltage applied to the top plates, and 11 www.national.com LM6588 TFT Display Application LM6588 TFT Display Application Figure 5 is a common test circuit used for measuring VCOM driver response time. The RC network of RL1 to RL3 and C1 to C4 models the distributed RC load of a VCOM line. This RC network is a gross simplification of what the actual impedance is on a TFT panel. However, it does provide a useful test for measuring the op amp's transient response when driving a large capacitive load. A low impedance MOSFET driver applies a 5V square wave to VSW, generating large current pulses in the RC network. Scope photos from this circuit are shown in Figure 6 and Figure 7. Figure 6 shows the test circuit generates positive and negative voltage spikes with an amplitude of 3.2V at the VCOM node, and both transients settle-out in approximately 2s. As mentioned before, the speed at which these transients settle-out is a function of the op amp's peak output current. The IOUT trace in Figure 7 shows that the LM6588 can sink and source peak currents of -200mA and 200mA. This ability to supply large values of output current makes the LM6588 extremely well suited for VCOM Driver applications. (Continued) 8KHz to 160KHz, which is much lower than the gain bandwidth of most op amps. As a result, the VCOM load adds very little phase lag when op amp loop gain is unity, and this allows the VCOM Driver to remain stable. This was verified by measuring the small-signal bandwidth of the LM6588 with the RC load of Figure 4. When driving an RC load of 50nF and 20, the LM6588 has a unity gain frequency of 6.12MHz with 41.5C of phase margin. If the load capacitor is increased to 200nF and the resistance remains 20, the unity gain frequency is virtually unchanged: 6.05MHz with 42.9C of phase margin. 20073429 FIGURE 4. VCOM Driver with Simplified Load A VCOM Driver's large-signal response time is determined by the op amp's maximum output current, not by its slew rate. This is easily shown by calculating how much output current is required to slew a 50nF load capacitance at the LM6588 slew rate of 14V/s: IOUT = 14V/s x 50nF = 700mA 20073431 700mA exceeds the maximum current specification for the LM6588 and almost all other op amps, confirming that a VCOM driver's speed is limited by its peak output current. In order to minimize VCOM transients, the op amp used as a VCOM Driver must supply large values of output current. FIGURE 6. VSW and VCOM Waveforms from VCOM 20073432 FIGURE 7. VSW and IOUT Waveforms from VCOM Test Circuit 20073430 FIGURE 5. VCOM Driver Test Circuit www.national.com 12 LM6588 TFT Display Application (Continued) GAMMA BUFFER Illumination in a TFT display, also referred to as grayscale, is set by a series of discrete voltage levels that are applied to each LCD pixel. These voltage levels are generated by resistive DAC networks that reside inside each of the column driver ICs. For example, a column driver with 64 Grayscale levels has a two 6 bit resistive DACs. Typically, the two DACs will have their 64 resistors grouped into four segments, as shown in Figure 8. Each of these segments is connected to external voltage lines, VGMA1 to VGMA10, which are the Gamma Levels. VGMA1 to VGMA5 set grayscale voltage levels that are positive with respect to VCOM (high polarity gamma levels). VGMA6 to VGMA10 set grayscale voltages negative with respect to VCOM (low polarity gamma levels). 20073434 FIGURE 9. Basic Gamma Buffer Configuration Another important specification for Gamma Buffers is small signal bandwidth and slew rate. When column drivers select which voltage levels are written to a row of pixels, their internal DACs inject current spikes into the Gamma Lines. This generates voltage transients at the Gamma Buffer outputs, and they should settle-out in less than 1s to insure a steady output voltage from the column drivers. Typically, these transients have a maximum amplitude of 2V, so a gamma buffer must have sufficient bandwidth and slew rate to recover from a 2V transient in 1s or less. 20073433 FIGURE 8. Simplified Schematic of Column Driver IC Figure 9 shows how column drivers in a TFT display are connected to the gamma levels. VGMA1, VGMA5, VGMA6, and VGMA10 are driven by the Gamma Buffers. These buffers serve as low impedance voltage sources that generate the display's gamma levels. The Gamma Buffers' outputs are set by a simple resistive ladder, as shown in Figure 9. Note that VGMA2 to VGMA4 and VGMA7 to VGMA9 are usually connected to the column drivers even though they are not driven by external buffers. Doing so, forces the gamma levels in all the column drivers to be identical, minimizing grayscale mismatch between column drivers. Referring again to Figure 9, the resistive load of a column driver DAC (i.e. resistance between GMA1 to GMA5) is typically 10k to 15k. On a typical display such as XGA, there can be up to 10 column drivers, so the total resistive load on a Gamma Buffer output can be as low as 1k. The voltage between VGMA1 and VGMA5 can range from 3V to 6V, depending on the type of TFT panel. Therefore, maximum load current supplied by a Gamma Buffer is approximately 6V/1k = 6mA, which is a relatively light load for most op amps. In many displays, VGMA1 can be less than 500mV below VDD, and VGMA10 can be less than 500mV above ground. Under these conditions, an op amp used for the Gamma Buffer must have rail-to-rail inputs and outputs, like the LM6588. 20073435 FIGURE 10. Large Signal Transient Response of an Operational Amplifier Figure 10 illustrates how an op amp responds to a largesignal transient. When such a transient occurs at t = 0, the output does not start changing until TPD, which is the op amp's propagation delay time (typically 20ns for the LM6588). The output then changes at the op amp's slew rate from t = TPD to TSR. From t = TSR to TSET, the output settles to its final value (VF) at a speed determined by the op amp's small-signal frequency response. Although propagation de13 www.national.com LM6588 TFT Display Application rails. Therefore, op amps used as panel repair buffers should have rail-to-rail input and stages. Otherwise, they may clip the column driver signal. The signal from a panel repair buffer is stored by a pixel when the pixel's row is selected. In high-resolution displays, each row is selected for as little as 11s. To insure that a pixel has adequate time to settle-out during this brief period, a panel repair buffer should settle to within 1% of its final value approximately 1s after a row is selected. This is hardest to achieve when transmitting a column line's maximum voltage swing, which is the difference between the upper and lower gamma levels (i.e. voltage between VGMA1 and VGMA10). For a LM6588, the most demanding application occurs in displays that operate from a 16V supply. In these displays, voltage difference between the top and bottom gamma levels can be as large as 15V, so the LM6588 needs to transmit a 15V pulse and settle to within 60mV of its final value in approximately 1s (60mV is approximately 1% of the dynamic range of the high or low polarity gamma levels). LM6588 settling times for 15V and -15V pulses were measured in a test circuit similar to the one in Figure 11. V+ and V- were set to 15.5V and -0.5V, respectively, when measuring settling time for a 0V to 15V pulse. Likewise, V+ and V- were set to 0.5V and -15.5V when measuring settling time for a 0V to -15V pulse. In both cases, the LM6588 output was connected to a series RC load of 51 and 200pF. When tested this way, the LM6588 settled to within 60mV of 15V or -15V in approximately 1.1s. These observed values are very close to the desired 1s specification, demonstrating that the LM6588 has the bandwidth and slew rate required for repair buffers in high-resolution TFT displays. (Continued) lay and slew limited response time (t = 0 to TSR) can be calculated from data sheet specifications, the small signal settling time (TSR to TSET) cannot. This is because an op amp's gain vs. frequency has multiple poles, and as a result, small-signal settling time can not be calculated as a simple function of the op amp's gain bandwidth. Therefore, the only accurate method for determining op amp settling time is to measure it directly. 20073436 FIGURE 11. Gamma Buffer Settling Time Test Circuit The test circuit in Figure 11 was used to measure LM6588 settling time for a 2V pulse and 1k load, which represents the maximum transient amplitude and output load for a gamma buffer. With this test system, the LM6588 settled to within 30mV of 2V pulse in approximately 170ns. Settling time for a 0 to -2V pulse was slightly less, 150ns. These values are much smaller than the desired response time of 1s, so the LM6588 has sufficient bandwidth and slew rate for regulating gamma line transients. PANEL REPAIR BUFFER It is not uncommon for a TFT panel to be manufactured with an open in one or two of its column or row lines. In order to repair these opens, TFT panels have uncommitted repair lines that run along their periphery. When an open line is identified during a panel's final assembly, a repair line reroutes its signal past the open. Figure 12 illustrates how a column is repaired. The column driver's output is sent to the other end of an open column via a repair line, and the repair line is driven by a panel repair buffer. When a column or row line is repaired, the capacitance on that line increases substantially. For instance, a column typically has 50pF to 100pF of line capacitance, but a repaired column can have up to 200pF. Column drivers are not designed to drive this extra capacitance, so a panel repair buffer provides additional output current to the repaired column line. Note that there is typically a 20 to 100 resistor in series with the buffer output. This resistor isolates the output from the 200pF of capacitance on a repaired column line, ensuring that the buffer remains stable. A pole is created by this resistor and capacitance, but its frequency will be in the range of 8MHz to 40MHz, so it will have only a minor effect on the buffer's transient response time. Panel repair buffers transmit a column driver signal, and as mentioned in the gamma buffer section, this signal is set by the gamma levels. It was also mentioned that many displays have upper and lower gamma levels that are within 500mV of the supply www.national.com 20073437 FIGURE 12. Panel Repair Buffer SUMMARY This application note provided a basic explanation of how op amps are used in TFT displays, and it also presented the specifications required for these op amps. There are three major op amp applications in a display: VCOM Driver, Gamma Buffer, and Panel Repair Buffer, and the LM6588 can be used for all of them. As a VCOM Driver, the LM6588 can supply large values of output current to regulate VCOM load transients. It has rail-to-rail input common-mode range and output swing required for gamma buffers and panel repair buffers. It also has the necessary gain bandwidth and slew-rate for regulating gamma levels and driving column repair lines. All these features make the LM6588 very well suited for use in TFT displays. 14 LM6588 Physical Dimensions inches (millimeters) unless otherwise noted 14-Pin SOIC NS Package Number M14A 14-Pin TSSOP NS Package Number MTC14 15 www.national.com LM6588 TFT-LCD Quad, 16V RRIO High Output Current Operational Amplifier Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated