TSOP48..ON1 Vishay Semiconductors IR Receiver Modules for Remote Control Systems Description The TSOP48..ON1 - series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. TSOP48..ON1 is the standard IR remote control receiver series, supporting all major transmission codes. 3 16115 Features Special Features * Photo detector and preamplifier in one package * Internal filter for PCM frequency e3 * Improved shielding against electrical field disturbance * TTL and CMOS compatibility * Output active low * Low power consumption * Lead (Pb)-free component * Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC * Improved immunity against ambient light * Suitable burst length 10 cycles/burst Parts Table Part Carrier Frequency TSOP4830ON1 30 kHz TSOP4833ON1 33 kHz TSOP4836ON1 36 kHz TSOP4837ON1 36.7 kHz TSOP4838ON1 38 kHz TSOP4840ON1 40 kHz TSOP4856ON1 56 kHz Block Diagram Application Circuit 16842 3 30 k VS 1 Input AGC Band Pass Demodulator OUT 2 PIN Control Circuit GND Transmitter TSOPxxxx with TSALxxxx Circuit 16833 R1 = 100 VS OUT GND + VS C1 = 4.7 F C VO GND R1 and C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously a a voltage below VO = 3.3 V by the external circuit. Document Number 82088 Rev. 1.6, 01-Mar-05 www.vishay.com 1 TSOP48..ON1 Vishay Semiconductors Absolute Maximum Ratings Absolute Maximum Ratings Tamb = 25 C, unless otherwise specified Symbol Value Supply Voltage Parameter (Pin 2) Test condition VS - 0.3 to + 6.0 V Supply Current (Pin 2) IS 5 mA Output Voltage (Pin 1) VO - 0.3 to + 6.0 V Output Current (Pin 1) IO 5 mA Junction Temperature Unit Tj 100 C Storage Temperature Range Tstg - 25 to + 85 C Operating Temperature Range Tamb - 25 to + 85 C Power Consumption (Tamb 85 C) Ptot 50 mW Soldering Temperature t 10 s Tsd 260 C Electrical and Optical Characteristics Tamb = 25 C, unless otherwise specified Symbol Min Typ. Max Unit Supply Current (Pin 3) Parameter VS = 5 V, Ev = 0 Test condition ISD 0.8 1.2 1.5 mA VS = 5 V, Ev = 40 klx, sunlight ISH 1.5 mA Transmission Distance Ev = 0, test signal see fig.1, IR diode TSAL6200, IF = 250 mA d 35 m Supply Voltage VS Output Voltage Low (Pin 3) = 0.7 mW/m2, IOSL = 0.5 mA, Ee test signal see fig. 1 VOSL Minimum Irradiance (56 kHz) Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.1 Ee min Minimum Irradiance (30 - 40 kHz) Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.1 Ee min Maximum Irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max Directivity Angle of half transmission distance www.vishay.com 2 1/2 4.5 5.5 V 250 mV 0.3 0.5 mW/m2 0.2 0.4 mW/m2 30 W/m2 45 deg Document Number 82088 Rev. 1.6, 01-Mar-05 TSOP48..ON1 Vishay Semiconductors Typical Characteristics (Tamb = 25 C unless otherwise specified) Optical Test Signal Ee 1.0 (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, T = 10 ms) Ton ,Toff - Output Pulse Width (ms) t tpi * * tpi T 10/fo is recommended for optimal function 16110 Output Signal VO 1) 2) VOH 7/f0 < td < 15/f0 tpi - 5/f 0 < tpo < tpi + 6/f 0 VOL tpo2 ) td1 ) 0.9 0.8 0.6 0.5 0.3 0.2 0.0 0.1 16909 1.0 10.0 100.0 1000.0 10000.0 Ee - Irradiance (mW/m) Figure 4. Output Pulse Diagram 1.2 Output Pulse 0.8 Input Burst Duration 0.7 0.6 0.5 0.4 0.3 0.2 = 950 nm, optical test signal, fig. 1 0.1 0.0 0.1 1.0 10.0 0.8 0.6 0.4 f = f0 5 % f (3 dB) = f0/10 0.2 0.0 0.7 100.0 1000.0 10000.0 16925 Ee - Irradiance (mW/m) 16908 1.0 E e min /E e - Rel. Responsivity 0.9 Figure 2. Pulse Length and Sensitivity in Dark Ambient 0.9 1.1 f/f0 - Relative Frequency 1.3 Figure 5. Frequency Dependence of Responsivity Optical Test Signal 4.0 600 s t 600 s T = 60 ms 94 8134 Output Signal, (see fig. 4) VOH VOL Ton Toff t Ee min - Threshold Irradiance (mW/m2 ) t po - Output Pulse Width (ms) = 950 nm, optical test signal, fig. 3 0.1 t 1.0 VO Toff 0.4 Figure 1. Output Function Ee Ton 0.7 3.5 3.0 2.5 2.0 1.5 Document Number 82088 Rev. 1.6, 01-Mar-05 Ambient, = 950 nm 1.0 0.5 0.0 0.01 16911 Figure 3. Output Function Correlation with ambient light sources: 10 W/m2 1.4 klx (Std.illum.A, T= 2855 K) 10 W/m2 8.2 klx (Daylight, T = 5900 K) 0.10 1.00 10.00 100.00 E - Ambient DC Irradiance (W/m 2) Figure 6. Sensitivity in Bright Ambient www.vishay.com 3 TSOP48..ON1 Vishay Semiconductors f = 10 kHz 1.0 f = 1 kHz 0.5 f = 100 Hz 16912 0.0 0.1 1.0 10.0 100.0 1000.0 VsRMS - AC Voltage on DC Supply Voltage (mV) E e min - Threshold Irradiance (mW/m) Figure 7. Sensitivity vs. Supply Voltage Disturbances Ee min - Threshold Irradiance (mW/m) f = fo 1.5 0.6 0.5 Sensitivity in dark ambient 0.4 0.3 0.2 0.1 0.0 - 30 - 15 0 15 30 45 60 75 16918 Tamb - Ambient Temperature (C) 90 Figure 10. Sensitivity vs. Ambient Temperature 1.2 2.0 f(E) = f0 1.6 1.2 0.8 0.4 0.0 0.0 0.4 0.8 1.2 1.6 2.0 S ( ) rel - Relative Spectral Sensitivity Ee min- Threshold Irradiance (mW/m) 2.0 1.0 0.8 0.6 0.4 0.2 0.0 750 E - Field Strength of Disturbance (kV/m) 94 8147 Figure 8. Sensitivity vs. Electric Field Disturbances 850 950 1050 1150 - Wavelength (nm) 16919 Figure 11. Relative Spectral Sensitivity vs. Wavelength 0 0.8 10 20 30 Max. Envelope Duty Cycle 0.7 0.6 40 0.5 1.0 0.4 0.9 50 0.8 60 0.3 0.2 f = 38 kHz, Ee = 2 mW/m2 70 0.7 0.1 80 0.0 0 16913 20 40 60 80 100 120 Burst Length (number of cycles/burst) Figure 9. Max. Envelope Duty Cycle vs. Burstlength www.vishay.com 4 0.6 96 12223p2 0.4 0.2 0 0.2 0.4 0.6 drel - Relative Transmission Distance Figure 12. Directivity Document Number 82088 Rev. 1.6, 01-Mar-05 TSOP48..ON1 Vishay Semiconductors Document Number 82088 Rev. 1.6, 01-Mar-05 IR Signal from fluorescent lamp with low modulation 0 5 16920 10 Time (ms) 15 20 Figure 13. IR Signal from Fluorescent Lamp with low Modulation IR Signal from fluorescent lamp with high modulation IR Signal The circuit of the TSOP48..ON1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpass filter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fulfill the following conditions: * Carrier frequency should be close to center frequency of the bandpass (e.g. 38 kHz). * Burst length should be 10 cycles/burst or longer. * After each burst which is between 10 cycles and 70 cycles a gap time of at least 14 cycles is necessary. * For each burst which is longer than 1.8 ms a corresponding gap time is necessary at some time in the data stream. This gap time should be at least 4 times longer than the burst. * Up to 800 short bursts per second can be received continuously. Some examples for suitable data format are: NEC Code (repetitive pulse), NEC Code (repetitive data), Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, R-2000 Code, Sony Code. When a disturbance signal is applied to the TSOP48..ON1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occur. Some examples for such disturbance signals which are suppressed by the TSOP48..ON1 are: * DC light (e.g. from tungsten bulb or sunlight) * Continuous signal at 38 kHz or at any other frequency * Signals from fluorescent lamps with electronic ballast with high or low modulation ( see Figure 13 or Figure 14 ). IR Signal Suitable Data Format 0 16921 5 10 Time (ms) 15 20 Figure 14. IR Signal from Fluorescent Lamp with high Modulation www.vishay.com 5 TSOP48..ON1 Vishay Semiconductors Package Dimensions in mm 16127 www.vishay.com 6 Document Number 82088 Rev. 1.6, 01-Mar-05 TSOP48..ON1 Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Document Number 82088 Rev. 1.6, 01-Mar-05 www.vishay.com 7