19 February 2013 Page 1 FEATURES SP75 Series 75W Open Frame Power Supply 5VDC to 58VDC in 1Volt Increments Remote Sense 1U Height 90-264 VAC Input UL/cUL , CB & DEMKO (EN60950) Approved RoHS Compliant 2x4 Footprint SPECIFICATION Model SP75-10500 Output Requirements Voltage (1) SP75-11200 SP75-11500 Input Requirements SP75-14800 SP75-15800 5V 12V 15V 24V 48V 58V Current Range 0 ~ 8A 0 ~ 6.25A 0 ~ 5A 0 ~ 3.12A 0 ~ 1.56A 0 ~ 1.29A Rated Power Ripple & Noise (Max) (2) Voltage Adjustment Range Voltage Tolerance 40W 75W 75W 75W 75W 75W 1% Pk to Pk 5% 5% Line Regulation 1% Load Regulation 5% Setup, Rise Time All output shall reach their steady state values within 3 Sec. of turn on Hold Time 20mS min. Voltage 90V ~ 264VAC Frequency Efficiency (Typ. @ 115V AC) 47Hz / 63Hz 68% 75% AC Current (max.) 84% 85% 85% 2.0A @ 115VAC Inrush Current (max.) Will not exceed 30A / 115VAC, Cold Start, 25C Short Circuit Protection Protection Requirement SP75-12400 Protection type : Hiccup mode, recovers automatically after fault condition is removed >150% rated output power Over- Current Protection Protection type : Hiccup mode, recovers automatically after fault condition is removed 115% ~ 135% rated output voltage Over voltage protection Environmental Conditions Protection type : Hiccup mode, Recycle AC to restart Operational -40C ~ 50C Temperature Range Storage Operational - 40C ~ +80C 20 ~ 90% RH non-condensing Working Humidity Storage Temperature Coefficient Vibration www.autec.com 5 ~ 95% R.H 0.01%/C typical on all outputs 3G, 10-25Hz, 15min. Per cycle for each axis (X, Y, Z) Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 85% 19 February 2013 Page 2 Model SP75-10500 SP75-11200 SP75-11500 Others Safety & EMC Safety Standards SP75-12400 SP75-13800 SP75-14800 UL/cUL (60950 2nd Ed) , DEMKO and CB Withstand Voltage EMI Conduction & Radiation EMS Immunity I/P - O/P: 3KVAC (4242 DC), 10mA for 1 minute EN55022 , FCC Class B EN61204, EN61000-3-2, EN61000-3-3 MTBF 150,000 hrs @ 25C based on MIL-STD-217F Dimension (L*W*H) 101.64*50.83*30.5 (mm) - 4.0*2.0*1.2 (inch) Weight 0.18kg - 0.40Lb PIN ASSIGNMENT SHIPPING SPECIFICATIONS AC DC Input Output PIN 1 Line +V PIN 2 NC +V PIN 3 Neutral + S (Remote Sense) Connector Series SP75 UNITSP PER CARTON 72.0 INDIVIDUL BOX DIEMENSION CARTON WEIGHT 13.27 Kgs 29.26 Lbs WIDTH LENGTH HEIGHT PIN 4 - S (Remote Sense) Series Inch 16.00 16.00 10.00 PIN 5 -V SP75 MM 406.4 406.4 254.0 PIN 6 -V Connector Molex 1063-4037 www.autec.com Molex 09-65-2065 Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 19 February 2013 Page 3 C8 C6 SPECIFICATION C 14 NOTES: 1. This family is from 5V to 48V in 1VDC increment, please consult Autec Sales with the right model # for your application. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance: includes set up tolerance, line regulation and load regulation. 4. Line regulation is measured from low line to high line at rated load. 5. Load regulation is measured from 0% to 100% rated load. 6. Specification subject to change without notice. www.autec.com Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777