Page 1
Autec Power Systems
667 E Cochran St, Simi Valley, CA93065
Tel: (805)522-0888
Fax: (805)522-8777
www.autec.com
19 February 2013
Model
SP75-10500
SP75-11500
SP75-12400
SP75-14800
SP75-15800
Output Requirements
Voltage (1)
5V
15V
24V
48V
58V
Current Range
0 ~ 8A
0 ~ 5A
0 ~ 3.12A
0 ~ 1.56A
0 ~ 1.29A
Rated Power
40W
75W
75W
75W
75W
Ripple & Noise
(Max) (2)
1% Pk to Pk
Voltage
Adjustment
Range
± 5%
Voltage
Tolerance
±5%
Line Regulation
±1%
Load Regulation
±5%
Setup, Rise Time
All output shall reach their steady state values within 3 Sec. of turn on
Hold Time
20mS min.
Input Requirements
Voltage
90V ~ 264VAC
Frequency
47Hz / 63Hz
Efficiency
(Typ. @ 115V
AC)
68%
84%
85%
AC Current (max.)
2.0A @ 115VAC
Inrush Current (max.)
Will not exceed 30A / 115VAC, Cold Start, 25°C
Protection
Requirement
Short Circuit Protection
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Over- Current Protection
>150% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Over voltage protection
115% ~ 135% rated output voltage
Protection type : Hiccup mode, Recycle AC to restart
Environmental Conditions
Temperature Range
-40°C ~ 50°C
- 40°C ~ +80°C
Working Humidity
20 ~ 90% RH non-condensing
5 ~ 95% R.H
Temperature Coefficient
±0.01%/°C typical on all outputs
Vibration
3G, 10-25Hz, 15min. Per cycle for each axis (X, Y, Z)
SP75 Series 75W Open Frame Power Supply
FEATURES
5VDC to 58VDC in 1Volt Increments
Remote Sense
1U Height
90-264 VAC Input
UL/cUL , CB & DEMKO (EN60950) Approved
RoHS Compliant
2x4 Footprint
SPECIFICATION
Page 2
Autec Power Systems
667 E Cochran St, Simi Valley, CA93065
Tel: (805)522-0888
Fax: (805)522-8777
www.autec.com
19 February 2013
Safety & EMC
Safety
Standards
UL/cUL (60950 2nd Ed) , DEMKO and CB
Withstand
Voltage
I/P - O/P: 3KVAC (4242 DC), 10mA for 1 minute
EMI
Conduction
& Radiation
EN55022 , FCC Class B
EMS
Immunity
EN61204, EN61000-3-2, EN61000-3-3
Others
MTBF
150,000 hrs @ 25°C based on MIL-STD-217F
Dimension
(L*W*H)
101.64*50.83*30.5 (mm) - 4.0*2.0*1.2 (inch)
Weight
0.18kg - 0.40Lb
Model
SP75-11200
SP75-11500
SP75-14800
PIN ASSIGNMENT
Connector
AC
DC
Input
Output
PIN 1
Line
+V
PIN 2
NC
+V
PIN 3
Neutral
+ S (Remote Sense)
PIN 4
- S (Remote Sense)
PIN 5
-V
PIN 6
-V
Connector
Molex 1063-4037
Molex 09-65-2065
SHIPPING SPECIFICATIONS
Series
UNITSP PER CARTON
CARTON WEIGHT
SP75
72.0
13.27 Kgs
29.26 Lbs
INDIVIDUL BOX
DIEMENSION
WIDTH
LENGTH
HEIGHT
Series
Inch
16.00
16.00
10.00
SP75
MM
406.4
406.4
254.0
Page 3
Autec Power Systems
667 E Cochran St, Simi Valley, CA93065
Tel: (805)522-0888
Fax: (805)522-8777
www.autec.com
19 February 2013
C6
C 8
C 14
NOTES:
1. This family is from 5V to 48V in 1VDC increment, please consult Autec Sales with the right model # for your
application.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf &
47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. Specification subject to change without notice.
SPECIFICATION