MQAC-415 - BANNER ENGINEERING

Self-Contained, AC-Operated Sensors

For complete technical information about this product, including dimensions, accessories, and specifications, see www.bannerengineering.com and search 121523

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing

so could lead to serious injury or death. This device does NOT include the

self-checking redundant circuitry necessary to allow its use in personnel safety

applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

Models

Sensing Mode Model1Output Range LED

OPPOSED

T303E -

60 m (200 ft) Infrared, 950 nmT30AW3R LO

T30RW3R DO

POLAR RETRO

T30AW3LP LO

6 m (20 ft) Visible Red, 680 nm

T30RW3LP DO

FIXED-FIELD

T30AW3FF200 LO

200 mm (8 in) cutoff

Infrared, 880 nm

T30RW3FF200 DO

T30AW3FF400 LO

400 mm (16 in) cutoff

T30RW3FF400 DO

T30AW3FF600 LO

600 mm (24 in) cutoff

T30RW3FF600 DO

Hookups

Cabled Emitters

bu 20-250V ac

QD Emitters (4-pin Micro-Style)

20-250V ac

No connection

rd/wh

rd/bk

All Other Cabled Models

20-250V ac

Load

All Other QD Models (4-pin Micro-Style)

20-250V ac

No Connection

Load

rd/wh

rd/bk

1Standard 2 m (6.5 ft) cable models are listed. For 9 m (30 ft) cable: add suffix “W/30” (for example, T303E W/30). For 4-pin Micro-style integral QD: add suffix “Q1” (for example,

T303EQ1). A model with a QD connector requires a mating cable.

T30 Sensors - AC-Voltage Series

P/N 116162 Rev. A 2/8/2013

0 116162 7

Specifications

Supply Voltage and Current

20 to 250V ac (50/60 Hz)

Average current: 20 mA

Peak current:

200 mA at 20V ac

500 mA at 120V ac

750 mA at 250V ac

Supply Protection Circuitry

Protected against transient voltages

Output Configuration

SPST solid-state ac switch; three-wire hookup; light operate or dark op-

erate, depending on model

Light Operate: Output conducts when sensor sees its own (or the emit-

ter’s) modulated light

Dark Operate: Output conducts when the sensor sees dark

Output Rating

300 mA maximum (continuous)

Fixed-Field models: derate 5 mA/°C above +50° C (+122° F)

Inrush capability: 1 amp for 20 ms, non-repetitive

OFF-state leakage current: < 100 mA

ON-state saturation voltage: 3V at 300 mA ac; 2V @ 15 mA ac

Output Protection Circuitry

Protected against false pulse on power-up

Output Response

Time Opposed mode: 16 ms ON, 8 ms OFF

Other models: 16 ms ON and OFF

NOTE: 100 ms delay on power-up; outputs do

not conduct during this time.

Repeatability

Opposed mode: 2 ms

Other models: 4 ms

Repeatability and response are independent of signal strength

Indicators

Two LEDs (Green and Yellow)

Green ON steady: power to sensor is ON

Yellow ON steady: sensor sees light

Yellow flashing: excess gain marginal (1 to 1.5x) in light condition

Construction

PBT polyester housing; polycarbonate (opposed-mode) or acrylic lens

Environmental Rating

Leakproof design rated NEMA 6P, DIN 40050 (IP69K)

Connections

2 m (6.5 ft) attached cable, or 4-pin Micro-style quick-disconnect fitting

Operating Conditions

Temperature: −40° to +70° C (−40° to +158° F)

Humidity: 90% at +50° C maximum relative humidity (non-condensing)

Vibration and Mechanical Shock

All models meet Mil. Std. 202F requirements. Method 201A (Vibration;

frequency 10 to 60 Hz, max., double amplitude 0.06 in acceleration

10G). Method 213B conditions H&I (Shock: 75G with unit operating;

100G for non-operation)

Certifications

Banner Engineering Corp Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.

will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty

period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE,

COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE

LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSE-

QUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARIS-

ING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product

previously manufactured by Banner Engineering Corp.

T30 Sensors - AC-Voltage Series