BZX84B5V1L
Zener Diode Data sheet
                                                               Outline
PD250 mW    
 
 
 
 
 
 
 
 
    
Feature Inner Circuit
High reliability
Small mold type
Application Packaging Specification
Voltage regulation Packing Embossed Tape
Reel Size(mm) 180
Taping Width(mm) 8
Structure Basic Ordering Unit(pcs) 3000
Silicon Epitaxial Planar Taping Code T116
Marking D3L
Absolute Maximum Rating (Ta = 25)
Parameter Symbol Condition Limits Unit
Power dissipation PDon Glass-epoxy substrate 250 mW
2.0 mW/°C
Junction temperature Tj- 150
Storage temperature Tstg - -65 150 
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved. 1/5
        
 2017/07/24_Rev.001
Not Recommended for
New Designs
BZX84B Series                        Data sheet
Characteristic (Ta = 2C)                             
P/N
Symbol
Zener Voltage:VZ(V) Reverse Current:
IRA)
Dynamic
Impedance:ZZ)
Temperature
Coefficient:γz
(mV/)
MIN. MAX. Iz
(mA) MAX. VR(V) MAX. Iz
(mA) MIN. MAX. Iz
(mA)
BZX84B5V1L 5.00 5.20 5 2 2.0 60 5 -1.5 2.6 5
BZX84B5V6L 5.49 5.71 5 1 2.0 40 5 -1.0 3.1 5
BZX84B6V2L 6.08 6.32 5 3 4.0 10 5 0.9 3.8 5
BZX84B6V8L 6.66 6.94 5 2 4.0 15 5 1.5 4.5 5
BZX84B7V5L 7.35 7.65 5 1 5.0 15 5 2.2 5.0 5
BZX84B8V2L 8.04 8.36 5 0.7 5.0 15 5 3.2 6.1 5
BZX84B9V1L 8.92 9.28 5 0.5 6.0 15 5 3.9 6.9 5
BZX84B10VL 9.80 10.20 5 0.2 7.0 20 5 5.0 8.0 5
BZX84B11VL 10.80 11.20 5 0.1 8.0 20 5 5.8 8.8 5
BZX84B12VL 11.80 12.20 5 0.1 8.0 25 5 6.8 9.8 5
BZX84B13VL 12.70 13.30 5 0.1 8.0 30 5 7.9 11.0 5
BZX84B15VL 14.70 15.30 5 0.1 10.0 30 5 9.4 12.6 5
BZX84B16VL 15.70 16.30 5 0.1 11.0 40 5 11.0 14.3 5
BZX84B18VL 17.60 18.40 5 0.1 13.0 45 5 12.6 15.8 5
BZX84B20VL 19.60 20.40 5 0.1 14.0 55 5 14.3 17.3 5
BZX84B22VL 21.60 22.40 5 0.1 15.0 55 5 15.8 19.3 5
BZX84B24VL 23.50 24.50 5 0.1 17.0 70 5 17.3 22.6 5
BZX84B27VL 26.50 27.50 2 0.1 19.0 80 2 19.3 25.8 2
BZX84B30VL 29.40 30.60 2 0.1 21.0 80 2 22.6 28.5 2
BZX84B33VL 32.30 33.70 2 0.1 23.0 80 2 25.8 31.1 2
BZX84B36VL 35.30 36.70 2 0.1 25.0 90 2 28.5 34.0 2
V
Z test time is 40ms
Marking      
P/N Marking P/N Marking
BZX84B5V1L D3L BZX84B15VL D3X
BZX84B5V6L D3M BZX84B16VL D3Y
BZX84B6V2L D3N BZX84B18VL D3Z
BZX84B6V8L D3P BZX84B20VL D5A
BZX84B7V5L D3Q BZX84B22VL D5B
BZX84B8V2L D3R BZX84B24VL D5C
BZX84B9V1L D3S BZX84B27VL D5D
BZX84B10VL D3T BZX84B30VL D5E
BZX84B11VL D3U BZX84B33VL D5F
BZX84B12VL D3V BZX84B36VL D5G
BZX84B13VL D3W    
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved. 2/5
        
2017/07/24_Rev.001
Not Recommended for
New Designs
BZX84B5V1L                        Data sheet
Characteristic Curves
                                             
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved. 3/5 2017/07/24_Rev.001
Not Recommended for
New Designs
BZX84B5V1L                        Data sheet
Characteristic Curves
                                             
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved. 4/5
        
2017/07/24_Rev.001
Not Recommended for
New Designs
BZX84B5V1L                        Data sheet
Dimension (SSD3 SOT-23 )
Taping (Unit:mm)
                                             
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved. 5/5  
2017/07/24_Rev.001
Not Recommended for
New Designs
Notice-PGA-E Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (Specific Applications), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHMs Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
EU
CHINA
CLASS
CLASSb
CLASS
CLASS
CLASS
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6.In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8.Confirm that operation temperature is within the specified range described in the product specification.
9.ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Not Recommended for
New Designs
Notice-PGA-E Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHMs internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Not Recommended for
New Designs
DatasheetDatasheet
Notice – WE Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHMs Products, please confirm the latest information with a ROHM sales
representative.
3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Not Recommended for
New Designs