100 MHz to 2.7 GHz, 45 dB RF Detector/Controller AD8314 Data Sheet FEATURES For convenience, the signal is internally ac-coupled, using a 5 pF capacitor to a load of 3 k in shunt with 2 pF. This highpass coupling, with a corner at approximately 16 MHz, determines the lowest operating frequency. Therefore, the source can be dc grounded. Complete RF detector/controller function Typical range:-58 dBV to -13 dBV -45 dBm to 0 dBm, re 50 Frequency response from 100 MHz to 2.7 GHz Temperature-stable linear-in-dB response Accurate to 2.7 GHz Rapid response: 70 ns to a 10 dB step Low power: 12 mW at 2.7 V Power down to 20 A The AD8314 provides two voltage outputs. The first, V_UP, increases from close to ground to about 1.2 V as the input signal level increases from 1.25 mV to 224 mV. This output is intended for use in measurement mode. Consult the Applications section for information on this mode. A capacitor can be connected between the V_UP and FLTR pins when it is desirable to increase the time interval over which averaging of the input waveform occurs. APPLICATIONS Cellular handsets (TDMA, CDMA , GSM) RSSI and TSSI for wireless terminal devices Transmitter power measurement and control The second output, V_DN, is an inversion of V_UP but with twice the slope and offset by a fixed amount. This output starts at about 2.25 V (provided the supply voltage is 3.3 V) for the minimum input and falls to a value close to ground at the maximum input. This output is intended for analog control loop applications. A setpoint voltage is applied to VSET, and V_DN is then used to control a VGA or power amplifier. Here again, an external filter capacitor can be added to extend the averaging time. Consult the Applications section for information on this mode. GENERAL DESCRIPTION The AD8314 is a complete low cost subsystem for the measurement and control of RF signals in the frequency range of 100 MHz to 2.7 GHz, with a typical dynamic range of 45 dB, intended for use in a wide variety of cellular handsets and other wireless devices. It provides a wider dynamic range and better accuracy than possible using discrete diode detectors. In particular, its temperature stability is excellent over the full operating range of -40C to +85C. The AD8314 is available in 8-lead MSOP and 8-lead LFCSP packages and consumes 4.5 mA from a 2.7 V to 5.5 V supply. When powered down, the typical sleep current is 20 A. Its high sensitivity allows control at low power levels, thus reducing the amount of power that needs to be coupled to the detector. It is essentially a voltage-responding device, with a typical signal range of 1.25 mV to 224 mV rms or -58 dBV to -13 dBV. This is equivalent to -45 dBm to 0 dBm, re 50 . FUNCTIONAL BLOCK DIAGRAM FLTR VSET V-I - + DET DET DET DET I-V V_UP X2 V_DN DET - RFIN 10dB 10dB 10dB AD8314 + BAND GAP REFERENCE VPOS ENBL 01086-001 OFFSET COMPENSATION 10dB COMM (PADDLE) Figure 1. Rev. C Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2002-2018 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD8314 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Transfer Function in Terms of Slope and Intercept ............... 12 Applications ....................................................................................... 1 dBV vs. dBm ............................................................................... 13 General Description ......................................................................... 1 Filter Capacitor ........................................................................... 13 Functional Block Diagram .............................................................. 1 Operating in Controller Mode ................................................. 13 Revision History ............................................................................... 2 Power-On and Enable Glitch .................................................... 14 Specifications..................................................................................... 3 Input Coupling Options ............................................................ 14 Absolute Maximum Ratings ............................................................ 4 Increasing the Logarithmic Slope in Measurement Mode ... 15 ESD Caution .................................................................................. 4 Effect of Waveform Type on Intercept .................................... 15 Pin Configurations and Function Descriptions ........................... 5 Mobile Handset Power Control Examples .............................. 16 Typical Performance Characteristics ............................................. 6 Operation at 2.7 GHz ................................................................. 18 Theory of Operation ...................................................................... 10 Using the LFCSP Package.......................................................... 18 Inverted Output .......................................................................... 11 Evaluation Board ........................................................................ 18 Applications ..................................................................................... 12 Outline Dimensions ....................................................................... 20 Basic Connections ...................................................................... 12 Ordering Guide .......................................................................... 20 REVISION HISTORY 1/2018--Rev. B to Rev. C Changes to Figure 3 .......................................................................... 5 Added EPAD to Table 3 ................................................................... 5 Updated Outline Dimensions ....................................................... 20 Changes to Ordering Guide .......................................................... 21 5/2006--Rev. A to Rev. B Updated Format .................................................................. Universal Changes to General Description .................................................... 1 Changes to Table 1 ............................................................................ 3 Changes to Table 2 ............................................................................ 4 Inserted Figure 3; Renumbered Sequentially ................................ 5 Changes to Figure 4, Figure 5, Figure 6, Figure 7, and Figure 8 ...................................................................................... 6 Changes to Figure 9, Figure 10, and Figure 12 ............................. 7 Changes to Figure 37 ...................................................................... 14 Changes to Table 5 .......................................................................... 15 Changes to Figure 39 ...................................................................... 16 Changes to Table 7 .......................................................................... 19 Updated Outline Dimensions ....................................................... 20 Changes to Ordering Guide .......................................................... 20 3/2002--Rev. 0 to Rev. A Edit to Product Description .............................................................1 Edit to Specifications.........................................................................2 Edit to Ordering Guide ....................................................................3 Edit to TPC 1......................................................................................4 New Section (Operation at 2.7 GHz) Added .............................. 14 Addition of New Figures 14 and 15 ............................................. 14 Changes to Evaluation Board Section.......................................... 14 Addition of Chip Scale Package.................................................... 16 10/1999--Revision 0: Initial Version Rev. C | Page 2 of 20 Data Sheet AD8314 SPECIFICATIONS VS = 3 V, TA = 25C, unless otherwise noted. Table 1. Parameter OVERALL FUNCTION Frequency Range 1 Input Voltage Range Equivalent Power Range Logarithmic Slope Logarithmic Intercept Equivalent dBm Level INPUT INTERFACE DC Resistance to COMM Inband Input Resistance Input Capacitance MAIN OUTPUT Voltage Range Minimum Output Voltage Maximum Output Voltage 3 General Limit Available Output Current Response Time Residual RF (at 2f ) INVERTED OUTPUT Gain Referred to V_UP Minimum Output Voltage Maximum Output Voltage Available Output Current Output-Referred Noise Response Time Full-Scale Settling Time SETPOINT INPUT Voltage Range Input Resistance Logarithmic Scale Factor ENABLE INTERFACE Logic Level to Enable Power Input Current when HI Logic Level to Disable Power POWER INTERFACE Supply Voltage Quiescent Current Overtemperature Total Supply Current when Disabled Overtemperature Conditions Min To meet all specifications Internally ac-coupled 52.3 external termination Main output, V_UP, 100 MHz 2 Main output, V_UP, 100 MHz 52.3 external termination Pin RFIN 0.1 1.25 -45 18.85 -68 -55 f = 0.1 GHz f = 0.1 GHz Pin V_UP V_UP connected to VSET No signal at RFIN, RL 10 k RL 10 k 2.7 V VS 5.5 V Sourcing/sinking 10% to 90%, 10 dB step f = 0.1 GHz (worst condition) Pin V_DN VDN = 2.25 V - 2 x VUP VS 3.3 V VS 3.3 V 4 Sourcing/sinking RF input = 2 GHz, -33 dBV, fNOISE = 10 kHz 10% to 90%, 10 dB input step -40 dBm to 0 dBm input step to 95% Pin VSET Corresponding to central 40 dB f = 0.900 GHz f = 1.900 GHz Pin ENBL HI condition, -40C TA +85C 2.7 V at ENBL, -40C TA +85C LO condition, -40C TA +85C Pin VPOS -40C TA +85C -40C TA +85C For a discussion on operation at higher frequencies, see Applications section. Mean and standard deviation specifications are available in Table 4. 3 Increased output possible when using an attenuator between V_UP and VSET to raise the slope. 4 Refer to Figure 22 for details. 1 2 Rev. C | Page 3 of 20 Typ Max Unit 21.3 -62 -49 2.5 224 0 23.35 -56 -43 GHz mV rms dBm mV/dB dBV dBm 100 3 2 0.01 0.01 1.9 VS - 1.1 1/0.5 0.01 2.1 4/100 0.15 7 0.02 2 VS - 1 2/1 70 100 -2 0.05 2.2 6/200 1.05 70 150 1.2 0.05 V V V V mA ns V 0.1 2.5 V V mA/A V/Hz ns ns 1.2 V k mV/dB mV/dB VPOS 300 +0.8 V A V 5.5 5.7 6.6 95 V mA mA A A 10 20.7 19.7 1.6 20 -0.5 2.7 3.0 2.7 k k pF 3.0 4.5 4.4 20 40 AD8314 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage VPOS V_UP, V_DN, VSET, ENBL Input Voltage Equivalent Power Internal Power Dissipation JA (MSOP) JA (LFCSP, Paddle Soldered) JA (LFCSP, Paddle Not Soldered) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering 60 sec) 8-Lead MSOP 8-Lead LFCSP Value 5.5 V 0 V, VPOS 1.6 V rms 17 dBm 200 mW 200C/W 80C/W 200C/W 125C -40C to +85C -65C to +150C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION 300C 240C Rev. C | Page 4 of 20 Data Sheet AD8314 RFIN 1 ENBL 2 AD8314 VSET 3 TOP VIEW (Not to Scale) FLTR 4 8 VPOS 7 V_DN 6 V_UP 5 COMM 01086-002 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 2. RM-8 Pin Configuration 8 VPOS AD8314 7 V_DN VSET 3 TOP VIEW (Not to Scale) 6 V_UP FLTR 4 5 COMM NOTES 1. EXPOSED PAD. THE EXPOSED PAD MUST BE CONNECTED TO GROUND. 01086-003 RFIN 1 ENBL 2 Figure 3. CP-8-23 Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2 3 4 Mnemonic RFIN ENBL VSET FLTR 5 6 7 8 COMM V_UP V_DN VPOS EPAD Description RF Input. Connect Pin to VS for Normal Operation. Connect pin to ground for disable mode. Setpoint Input for Operation in Controller Mode. To operate in detector mode connect VSET to V_UP. Connection for an External Capacitor to Slow the Response of the Output. Capacitor is connected between FLTR and V_UP. Device Common (Ground) Logarithmic Output. Output voltage increases with increasing input amplitude. Inversion of V_UP, Governed by: V_DN = 2.25 V - 2 x VUP. Positive Supply Voltage (VS), 2.7 V to 5.5 V. Exposed Pad. Connect EPAD via a low impedance path to ground. CP-8-23 only. Rev. C | Page 5 of 20 AD8314 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 1.2 4 0.1GHz 3 1.0 2.5GHz 2 1.9GHz 0.9GHz VUP (V) 1.9GHz 0.6 2.5GHz 0.1GHz 1 ERROR (dB) 0.8 0 -1 0.9GHz 0.4 -2 0.2 -65 -45 -55 (-52dBm) -25 -35 INPUT AMPLITUDE (dBV) -15 -5 (-2dBm) -4 -70 01086-004 0 -75 -60 -50 (-47dBm) Figure 4. VUP vs. Input Amplitude -40 -30 -20 INPUT AMPLITUDE (dBV) -10 0 (+3dBm) 01086-007 -3 Figure 7. Log Conformance vs. Input Amplitude 1.2 1.0 3 1.2 3 2 1.0 2 1 0.8 +25C +25C 0.4 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C 0.2 0 -70 (-47dBm) -50 -40 -30 -20 INPUT AMPLITUDE (dBV) -10 0.4 -2 0.2 0 (+3dBm) 0 -40C -1 -3 -60 +25C 0.6 0 -70 ERROR (dB) 0 1 -1 -2 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C -3 -60 -50 (-47dBm) -40 -30 -20 INPUT AMPLITUDE (dBV) 01086-008 -40C 0.6 VUP (V) +85C 01086-005 VUP (V) -40C ERROR (dB) +85C 0.8 0 -10 (+3dBm) Figure 5. VUP and Log Conformance vs. Input Amplitude at 0.1 GHz; -40C, +25C, and +85C Figure 8. VUP and Log Conformance vs. Input Amplitude at 1.9 GHz; -40C, +25C, and +85C 1.2 3 1.2 3 2 1.0 2 1 0.8 1.0 +25C 0.4 0.2 0 -70 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C (-47dBm) -50 -40 -30 -20 INPUT AMPLITUDE (dBV) -10 -40C 0.4 -2 0.2 0 (+3dBm) 0 Figure 6. VUP and Log Conformance vs. Input Amplitude at 0.9 GHz; -40C, +25C, and +85C 0 -70 ERROR (dB) +25C 0.6 -1 -3 -60 1 -1 -2 SLOPE AND INTERCEPT NORMALIZED AT +25C AND APPLIED TO -40C AND +85C -3 -60 (-47dBm) -50 -40 -30 -20 INPUT AMPLITUDE (dBV) -10 0 (+3dBm) Figure 9. VUP and Log Conformance vs. Input Amplitude at 2.5 GHz; -40C, +25C, and +85C Rev. C | Page 6 of 20 01086-009 0 -40C VUP (V) 0.6 +85C +85C ERROR (dB) VUP (V) +85C 01086-006 0.8 Data Sheet AD8314 23 -55 -40C -40C -60 VUP INTERCEPT (dBV) VUP SLOPE (mV/dB) 22 21 +25C 20 +85C +25C -65 +85C -70 0.5 0 1.0 1.5 2.0 2.5 FREQUENCY (GHz) -75 01086-010 18 0.5 0 1.0 1.5 2.0 2.5 FREQUENCY (GHz) Figure 10. Slope vs. Frequency; -40C, +25C, and +85C 01086-013 19 Figure 13. VUP Intercept vs. Frequency; -40C, +25C, and +85C 22 -61 0.1GHz -62 VUP INTERCEPT (dBV) VUP SLOPE (mV/dB) 0.1GHz 21 0.9GHz 20 1.9GHz 2.5GHz -63 0.9GHz -64 -65 -66 2.5GHz 3.5 4.0 4.5 5.0 5.5 VS (V) 3.5 4.0 4.5 5.0 5.5 VS (V) Figure 11. VUP Slope vs. Supply Voltage 3500 3.0 01086-014 3.0 1.9GHz -67 2.5 01086-011 19 2.5 Figure 14. VUP Intercept vs. Supply Voltage 0 6 -200 5 2000 -400 -600 -800 1500 X R -1000 1000 R -1200 500 0 0 0.5 1.0 1.5 FREQUENCY (GHz) 2.0 -1400 2.5 4 DECREASING VENBL 3 INCREASING VENBL 2 1 0 01086-012 RESISTANCE () 2500 R || - jX 3030 || - j748 760 || - j106 301 || - j80 90 || - j141 Figure 12. Input Impedance -1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 VENBL (V) Figure 15. Supply Current vs. ENBL Voltage, VS = 3 V Rev. C | Page 7 of 20 2.6 01086-015 FREQUENCY (GHz) 0.1 0.9 1.9 2.5 REACTANCE () 3000 SUPPLY CURRENT (mA) X AD8314 Data Sheet AVERAGE: 128 SAMPLES AVERAGE: 128 SAMPLES VDN 1V/VERTICAL DIVISION VDN 500mV/VERTICAL DIVISION VDN GND GND VUP 500mV/ VERTICAL DIVISION 1s PER HORIZONTAL DIVISION PULSED RF 0.1GHz, -13dBV 5V PER VERTICAL DIVISION VENBL GND Figure 19. VUP and VDN Response Time, -40 dBm to 0 dBm Figure 16. ENBL Response Time HP8648B SIGNAL GENERATOR -33dBV EXT TRIG 10MHz REF OUTPUT RF OUT HP8116A PULSE GENERATOR TRIG OUT HP8648B SIGNAL GENERATOR PULSE MODULATION MODE PULSE OUT 52.3 VPOS 8 2 ENBL V_DN 7 TEK P6204 FET PROBE TEK P6204 FET PROBE V_UP 6 3 VSET OUT TEK TDS784C SCOPE TRIG OUT 3.0V 0.1F 1 RFIN VPOS 8 2 ENBL V_DN 7 52.3 3.0V AD8314 01086-017 NC = NO CONNECT PICOSECOND PULSE LABS PULSE GENERATOR TEK P6204 FET PROBE -3dB COMM 5 NC 4 FLTR PULSE MODE IN RF SPLITTER TRIG AD8314 EXT TRIG 10MHz REF OUTPUT RF OUT -3dB 3.0V 0.1F 1 RFIN 100ns PER HORIZONTAL DIVISION 200mV PER VERTICAL DIVISION 01086-016 VENBL 3 VSET V_UP 6 NC 4 FLTR COMM 5 TRIG TEK P6204 FET PROBE TEK P6204 FET PROBE TEK TDS784C SCOPE 01086-020 VUP GND GND RF INPUT 01086-019 VUP 500mV/VERTICAL DIVISION NC = NO CONNECT Figure 20. Text Setup for Pulse Response 1k 10k 100k 1M FREQUENCY (Hz) 10 NOISE SPECTRAL DENSITY (V/Hz) RF INPUT -70dBm -50dBm -60dBm -40dBm 1 -20dBm -30dBm 0.1 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 21. VDN Noise Spectral Density Figure 18. AC Response from VSET to V_DN Rev. C | Page 8 of 20 10M 01086-021 100 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 10M 01086-018 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 -5 10 PHASE (Degrees) AMPLITUDE (dB) Figure 17. Test Setup for ENBL Response Time Data Sheet AD8314 2.3 2.3 0mA 2mA SHADING INDICATES 3 SIGMA 4mA 2.1 VDN (V) 2.0 6mA 2.0 1.9 1.9 1.8 1.8 2.8 2.9 3.0 3.1 3.2 3.3 3.4 1.7 2.7 01086-022 1.7 2.7 3.5 VS (V) 2.8 2.9 VUP 500mV/VERTICAL DIVISION VPOS AND ENABLE 2V PER VERTICAL DIVISION EXT TRIG RF OUT 2 ENBL VPOS 8 V_DN 7 AD8314 3 VSET V_UP 6 NC 4 FLTR COMM 5 TEK P6204 FET PROBE EXT TRIG AD811 1 RFIN TRIG 52.3 TEK TDS784C SCOPE NC = NO CONNECT 2 ENBL VPOS 8 732 V_DN 7 TEK P6204 FET PROBE AD8314 0.2 TRIG OUT HP8112A PULSE GENERATOR PULSE OUT 49.9 732 TEK P6204 FET PROBE 10MHz REF OUTPUT RF OUT 3 VSET NC 4 FLTR 01086-024 1 RFIN 52.3 HP8648B SIGNAL GENERATOR PULSE OUT AD811 01086-026 Figure 26. Power-On Response, VDN, Controller Mode with VSET Held Low TRIG OUT HP8116A PULSE GENERATOR 100ns PER HORIZONTAL DIVISION 2V PER VERTICAL DIVISION GND 01086-023 1s PER HORIZONTAL DIVISION Figure 23. Power-On and Power-Off Response, Measurement Mode 10MHz REF OUTPUT 3.5 VDN VDN GND GND 3.4 200mV PER VERTICAL DIVISION VDN GND VPOS AND ENABLE 3.3 AVERAGE: 128 SAMPLES VUP 500mV/VERTICAL DIVISION VUP GND 3.2 Figure 25. Maximum VDN Voltage vs. VS with 3 mA Load AVERAGE: 128 SAMPLES VUP -33dBV 3.1 VS (V) Figure 22. Maximum VDN Voltage vs. VS by Load Current HP8648B SIGNAL GENERATOR 3.0 V_UP 6 NC 49.9 TRIG TEK TDS784C SCOPE COMM 5 NC = NO CONNECT Figure 27. Test Setup for Power-On Response at V_DN Output, Controller Mode with VSET Pin Held Low Figure 24. Test Setup for Power-On and Power-Off Response Rev. C | Page 9 of 20 01086-027 2.1 VDN (V) 2.2 01086-025 2.2 AD8314 Data Sheet THEORY OF OPERATION However, in using this part, it must be understood that log amps do not fundamentally respond to power. It is for this reason the dBV is used (decibels above 1 V rms) rather than the commonly used metric of dBm. While the dBV scaling is fixed, independent of termination impedance, the corresponding power level is not. For example, 224 mV rms is always -13 dBV (with one further condition of an assumed sinusoidal waveform; see the Applications section for more information on the effect of waveform on logarithmic intercept), and it corresponds to a power of 0 dBm when the net impedance at the input is 50 . When this impedance is altered to 200 , the same voltage clearly represents a power level that is four times smaller (P = V2/R), that is, -6 dBm. Note that dBV can be converted to dBm for the special case of a 50 system by simply adding 13 dB (0 dBV is equivalent to +13 dBm). The AD8314 is a logarithmic amplifier (log amp) similar in design to the AD8313; further details about the structure and function can be found in the AD8313 data sheet and other log amps produced by ADI. Figure 28 shows the main features of the AD8314 in block schematic form. The AD8314 combines two key functions needed for the measurement of signal level over a moderately wide dynamic range. First, it provides the amplification needed to respond to small signals, in a chain of four amplifier/limiter cells, each having a small signal gain of 10 dB and a bandwidth of approximately 3.5 GHz. At the output of each of these amplifier stages is a full-wave rectifier, essentially a square-law detector cell, that converts the RF signal voltages to a fluctuating current having an average value that increases with signal level. A further passive detector stage is added prior to the first stage. Therefore, there are five detectors, each separated by 10 dB, spanning some 50 dB of dynamic range. The overall accuracy at the extremes of this total range, viewed as the deviation from an ideal logarithmic response, that is, the law-conformance error, can be judged by reference to Figure 7, which shows that errors across the central 40 dB are moderate. Figure 5, Figure 6, Figure 8 through Figure 11, Figure 13, and Figure 14 show how the conformance to an ideal logarithmic function varies with supply voltage, temperature, and frequency. Therefore, the external termination added prior to the AD8314 determines the effective power scaling. This often takes the form of a simple resistor (52.3 provides a net 50 input), but more elaborate matching networks can be used. This impedance determines the logarithmic intercept, the input power for which the output would cross the baseline (V_UP = zero) if the function were continuous for all values of input. Because this is never the case for a practical log amp, the intercept refers to the value obtained by the minimum-error straight-line fit to the actual graph of V_UP vs. PIN (more generally, VIN). Again, keep in mind that the quoted values assume a sinusoidal (CW) signal. Where there is complex modulation, as in CDMA, the calibration of the power response needs to be adjusted accordingly. Where a true power (waveformindependent) response is needed, the use of an rms-responding detector, such as the AD8361, should be considered. The output of these detector cells is in the form of a differential current, making their summation a simple matter. It can easily be shown that such summation closely approximates a logarithmic function. This result is then converted to a voltage, at Pin V_UP, through a high-gain stage. In measurement modes, this output is connected back to a voltage-to-current (V-I) stage, in such a manner that V_UP is a logarithmic measure of the RF input voltage, with a slope and intercept controlled by the design. For a fixed termination resistance at the input of the AD8314, a given voltage corresponds to a certain power level. FLTR VSET V-I - + DET DET DET DET I-V V_UP X2 V_DN DET - RFIN 10dB OFFSET COMPENSATION 10dB 10dB AD8314 + BAND GAP REFERENCE VPOS ENBL 01086-028 10dB COMM (PADDLE) Figure 28. Block Schematic Rev. C | Page 10 of 20 Data Sheet AD8314 Table 4. Typical Specifications at Selected Frequencies at 25C (Mean and ) 1 dB Dynamic Range 1 (dBV) Frequency (GHz) 0.1 0.9 1.9 2.5 Intercept (dBV) High Point Low Point 21.3 0.4 -62.2 0.4 -11.8 0.3 -59 0.5 20.7 19.7 19.2 0.4 0.4 0.4 -63.6 -66.3 -62.1 0.4 0.4 0.7 -13.8 -19 -16.4 0.3 0.7 1.7 -61.4 -64 -61 0.4 0.6 1.3 Refer to Figure 32. V_UP CURRENTS FROM DETECTORS V_DN + VSET V-I AD8314 VDN = 2.25V - 2.0 x V_UP FLTR BAND GAP REFERENCE 1.125V Figure 29. Output Interfaces 2.5 OUTPUT FOR PA CONTROL 2.0 INVERTED OUTPUT V_DN 1.5 VOLTS The second provision is the inclusion of an inverting amplifier to the output, for use in controller applications. Most power amplifiers require a gain-control bias that must decrease from a large positive value toward ground level as the power output is required to decrease. This control voltage, which appears at Pin V_DN, is not only of the opposite polarity to V_UP, but also needs to have an offset added to determine its most positive value when the power level (assumed to be monitored through a directional coupler at the output of the PA) is minimal. +2 I-V 01086-029 However, the logarithmic slope, the amount by which the output V_UP changes for each decibel of input change (voltage or power) is, in principle, independent of waveform or termination impedance. In practice, it usually falls off somewhat at higher frequencies, due to the declining gain of the amplifier stages and other effects in the detector cells. For the AD8314, the slope at low frequencies is nominally 21.3 mV/dB, falling almost linearly with frequency to about 19.2 mV/dB at 2.5 GHz. These values are sensibly independent of temperature (see Figure 10) and almost totally unaffected by the supply voltage from 2.7 V to 5.5 V (see Figure 11). The starting value of V_DN is nominally 2.25 V, and it falls on a slope of twice that of V_UP; in other words,-43 mV/dB. Figure 29 shows how this is achieved: the reference voltage that determines the maximum output is derived from the on-chip voltage reference and is substantially independent of the supply voltage or temperature. However, the full output cannot be attained for supply voltages under 3.3 V; Figure 22 shows this dependency. The relationship between V_UP and V_DN is shown in Figure 30. Rev. C | Page 11 of 20 1.0 0.5 0 -60 OUTPUT FOR MEASUREMENT -50 -40 V_UP -30 -20 -10 INPUT AMPLITUDE (dBV) Figure 30. Showing V_UP and V_DN Relationship 0 01086-030 1 Slope (mV/dB) AD8314 Data Sheet APPLICATIONS BASIC CONNECTIONS Figure 31 shows connections for the basic measurement mode. A supply voltage of 2.7 V to 5.5 V is required. The supply to the VPOS pin should be decoupled with a low inductance 0.1 F surface-mount ceramic capacitor. A series resistor of about 10 can be added; this resistor slightly reduces the supply voltage to the AD8314 (maximum current into the VPOS pin is approximately 9 mA when V_DN is delivering 5 mA). Its use should be avoided in applications where the power supply voltage is very low (that is, 2.7 V). A series inductor provides similar power supply filtering with minimal drop in supply voltage. 52.3 3 1.2 VS = 3V RT = 52.3 2 1.0 OPTIONAL (SEE TEXT) 2 ENBL V_DN 7 VS VDN V_UP 6 4 FLTR COMM 5 1 0.6 0 0.4 -1 VUP 0.2 01086-031 3 VSET 0.8 INTERCEPT 0 -70 Figure 31. Basic Connections for Operation in Measurement Mode The ENBL pin is here connected to VPOS. The AD8314 can be disabled by pulling this pin to ground when the chip current is reduced to about 20 A from its normal value of 4.5 mA. The logic threshold is around +VS/2 and the enable function occurs in about 1.5 s. Note, however, further settling time is generally needed at low input levels. The AD8314 has an internal input coupling capacitor. This eliminates the need for external ac coupling. A broadband input match is achieved in this example by connecting a 52.3 resistor between RFIN and ground. This resistance combines with the internal input impedance of approximately 3 k to give an overall broadband input resistance of 50 . Several other coupling methods are possible, which are described in the Input Coupling Options section. The measurement mode is selected by connecting VSET to V_UP, which establishes a feedback path and sets the logarithmic slope to its nominal value. The peak voltage range of the measurement extends from -58 dBV to -13 dBV at 0.9 GHz, and only slightly less at higher frequencies up to 2.5 GHz. Therefore, using the 50 termination, the equivalent power range is -45 dBm to 0 dBm. At a slope of 21.5 mV/dB, this would amount to an output span of 967 mV. Figure 32 shows the transfer function for V_UP at a supply voltage of 3 V and input frequency of 0.9 GHz. -2 3dB DYNAMIC RANGE -3 -60 (-47dBm) -50 -40 -30 -20 INPUT AMPLITUDE (dBV) -10 0 (+3dBm) 01086-032 VPOS 8 ERROR (dB) 1dB DYNAMIC RANGE AD8314 CF OPTIONAL (SEE TEXT) While V_DN can deliver up to 6 mA, the load resistance on V_UP should not be lower than 10 k in order that the fullscale output of 1 V can be generated with the limited available current of 200 A maximum. Figure 32 shows the logarithmic conformance under the same conditions. VUP (V) VS VDN = 2.25 V - 2 VUP 0.1F 1 RFIN INPUT V_DN, which is generally not used when the AD8314 is used in measurement mode, is essentially an inverted version of V_UP. The voltage on V_UP and V_DN are related by Figure 32. VUP and Log Conformance Error vs. Input Level vs. Input Level at 900 MHz TRANSFER FUNCTION IN TERMS OF SLOPE AND INTERCEPT The transfer function of the AD8314 is characterized in terms of its slope and intercept. The logarithmic slope is defined as the change in the RSSI output voltage for a 1 dB change at the input. For the AD8314, slope is nominally 21.5 mV/dB. Therefore, a 10 dB change at the input results in a change at the output of approximately 215 mV. Log conformance plot, Figure 32, shows the range over which the device maintains its constant slope. The dynamic range can be defined as the range over which the error remains within a certain band, usually 1 dB or 3 dB. In Figure 32 for example, the 1 dB dynamic range is approximately 50 dB (from -13 dBV to -63 dBV). Rev. C | Page 12 of 20 Data Sheet AD8314 where: VUP is the demodulated and filtered RSSI output. VSLOPE is the logarithmic slope, expressed in V/dB. PIN is the input signal, expressed in decibels relative to some reference level (either dBm or dBV in this case). PO is the logarithmic intercept, expressed in decibels relative to the same reference level. For example, at an input level of -40 dBV (-27 dBm), the output voltage is VOUT = 0.020 V/dB x [-40 dBV - (-63 dBV)] = 0.46 V dBV VS. dBm The most widely used convention in RF systems is to specify power in dBm, that is, decibels above 1 mW in 50 . Specification of log amp input levels in terms of power is strictly a concession to popular convention; they do not respond to power (tacitly power absorbed at the input), but to the input voltage. The use of dBV, defined as decibels with respect to a 1 V rms sine wave, is more precise, although this is still not unambiguous because waveform is also involved in the response of a log amp, which, for a complex input (such as a CDMA signal), does not follow the rms value exactly. Since most users specify RF signals in terms of power (more specifically, in dBm/50 ), both dBV and dBm are used in specifying the performance of the AD8314 showing equivalent dBm levels for the special case of a 50 environment. Values in dBV are converted to dBm re 50 by adding 13. 52.3 INPUT VS 0.1F 1 RFIN VPOS 8 VS 2 ENBL V_DN 7 VDN AD8314 VSET 3 VSET V_UP 6 4 FLTR COMM 5 CF Figure 33. Basic Connections for Operation in Controller Mode POWER AMPLIFIER RF INPUT DIRECTIONAL COUPLER FILTER CAPACITOR The video bandwidth of both V_UP and V_DN is approximately 3.5 MHz. In CW applications where the input frequency is much higher than this, no further filtering of the demodulated signal is required. Where there is a low frequency modulation of the carrier amplitude, however, the low-pass corner must be reduced by the addition of an external filter capacitor, CF (see Figure 31). The video bandwidth is related to CF by 1 Video Bandwidth = 2 x 13 k x (3.5 pF + C F ) Figure 33 shows the basic connections for operation in the controller mode, and Figure 34 shows a block diagram of a typical controller mode application. The feedback from V_UP to VSET is broken and the desired setpoint voltage is applied to VSET from the controlling source (often this is a DAC). VDN rails high (2.2 V on a 3.3 V supply, and 1.9 V on a 2.7 V supply) when the applied power is less than the value corresponding to the setpoint voltage. When the input power slightly exceeds this value, VDN would, in the absence of the loop via the power amplifier gain pin, decrease rapidly toward ground. In the closed loop, however, the reduction in VDN causes the power amplifier to reduce its output. This restores a balance between the actual power level sensed at the input of the AD8314 and the demanded value determined by the setpoint. This assumes that the gain control sense of the variable gain element is positive, that is, an increasing voltage from V_DN tends to increase gain. The output swing and current sourcing capability of V_DN are shown in Figure 22 and Figure 25. 01086-033 VUP = VSLOPE x (PIN - PO) OPERATING IN CONTROLLER MODE GAIN CONTROL VOLTAGE CF V_UP FLTR V_DN VSET DAC AD8314 RFIN 52.3 01086-034 The intercept is the point at which the extrapolated linear response would intersect the horizontal axis (see Figure 32). Using the slope and intercept, the output voltage can be calculated for any input level within the specified input range by Figure 34. Typical Controller Mode Application The relationship between the input level and the setpoint voltage follows from the nominal transfer function of the device (VUP vs. input amplitude, see Figure 4). For example, a voltage of 1 V on VSET demands a power level of 0 dBm at RFIN. The corresponding power level at the output of the power amplifier is greater than this amount due to the attenuation through the directional coupler. Rev. C | Page 13 of 20 AD8314 Data Sheet As previously mentioned, the AD8314 can be put into a low power mode by pulling the ENBL pin to ground. This reduces the quiescent current from 4.5 mA to 20 A. Alternatively, the supply can be turned off to eliminate the quiescent current. Figure 16 and Figure 26 show the behavior of the V_DN output under these two conditions (in Figure 26, ENBL is tied to VPOS). The glitch that results in both cases can be reduced by loading the V_DN output. INPUT COUPLING OPTIONS The impedance matching characteristics of a reactive matching network provide voltage gain ahead of the AD8314; this increases the device sensitivity (see Table 5). The voltage gain is calculated by Voltage GaindB 20 log10 R2 R1 where R2 is the input impedance of the AD8314, and R1 is the source impedance to which the AD8314 is being matched. Note that this gain is only achieved for a perfect match. Component tolerances and the use of standard values tend to reduce gain. The internal 5 pF coupling capacitor of the AD8314, along with the low frequency input impedance of 3 k, gives a high-pass input corner frequency of approximately 16 MHz. This sets the minimum operating frequency. Figure 35 through Figure 37 show three options for input coupling. A broadband resistive match can be implemented by connecting a shunt resistor to ground at RFIN (see Figure 35). This 52.3 resistor (other values can also be used to select different overall input impedances) combines with the input impedance of the AD8314 (3 k||2 pF) to give a broadband input impedance of 50 . While the input resistance and capacitance (CIN and RIN) varies by approximately 20% from device to device, the dominance of the external shunt resistor means that the variation in the overall input impedance is close to the tolerance of the external resistor. At frequencies above 2 GHz, the input impedance drops below 250 (see Figure 12), so it is appropriate to use a larger value shunt resistor. This value is calculated by plotting the input impedance (resistance and capacitance) on a Smith Chart and choosing the best value shunt resistor to bring the input impedance closest to the center of the chart. At 2.5 GHz, a shunt resistor of 165 is recommended. Rev. C | Page 14 of 20 50 SOURCE 50 AD8314 RFIN RSHUNT 52.3 CC CIN RIN 01086-035 POWER-ON AND ENABLE GLITCH In Figure 36, the matching components are drawn as general reactances. Depending on the frequency, the input impedance at that frequency, and the availability of standard value components, either a capacitor or an inductor is used. As in the previous case, the input impedance at a particular frequency is plotted on a Smith Chart and matching components are chosen (shunt or Series L, shunt or Series C) to move the impedance to the center of the chart. Table 5 gives standard component values for some popular frequencies. Matching components for other frequencies can be calculated using the input resistance and reactance data over frequency, which is given in Figure 12. Note that the reactance is plotted as though it appears in parallel with the input impedance (which it does because the reactance is primarily due to input capacitance). VBIAS Figure 35. Broadband Resistive 50 SOURCE 50 AD8314 RFIN X1 CC X2 CIN VBIAS Figure 36. Narrowband Reactive 50 STRIPLINE RATTN AD8314 RFIN CC CIN VBIAS Figure 37. Series Attenuation RIN RIN 01086-036 The transient response of this control loop is determined by the filter capacitor, CF. When this is large, the loop is unconditionally stable (by virtue of the dominant pole generated by this capacitor), but the response is sluggish. The minimum value ensuring stability should be used, requiring full attention to the particulars of the power amplifier control function. Because this is invariably nonlinear, the choice must be made for the worstcase condition, which usually corresponds to the smallest output from the PA, where the gain function is steepest. In practice, an improvement in loop dynamics can often be achieved by adding a response zero, formed by a resistor in series with CF. A reactive match can also be implemented as shown in Figure 36. This is not recommended at low frequencies as device tolerances dramatically varies the quality of the match because of the large input resistance. For low frequencies, Figure 35 or Figure 37 is recommended. 01086-037 When connected in a PA control loop, as shown in Figure 34, the voltage VUP is not explicitly used but is implicated in again setting up the required averaging time, by choice of CF. However, now the effective loop response time is a much more complicated function of the PA's gain-control characteristics, which are very nonlinear. A complete solution requires specific knowledge of the power amplifier. Data Sheet AD8314 Figure 37 shows a third method for coupling the input signal into the AD8314, applicable in applications where the input signal is larger than the input range of the log amp. A series resistor, connected to the RF source, combines with the input impedance of the AD8314 to resistively divide the input signal being applied to the input. This has the advantage of very little power being tapped off in RF power transmission applications. Table 5. X1 and X2 Recommended Components in Figure 36 Frequency (GHz) 0.1 X1 Short X2 52.3 Voltage Gain (dB) 0.9 1.9 2.5 33 nH 10 nH 1.5 pF 39 nH 15 nH 3.9 nH 11.8 7.8 2.55 INCREASING THE LOGARITHMIC SLOPE IN MEASUREMENT MODE The nominal logarithmic slope of 21.5 mV/dB (see Figure 10 for the variation of slope with frequency) can be increased to an arbitrarily high value by attenuating the signal between V_UP and VSET, as shown in Figure 38. The ratio R1/R2 is set by New Slope -1 R1/ R2 = Original Slope In the example shown, two 5 k resistors combine to change the slope at 1900 MHz from 20 mV/dB to 40 mV/dB. The slope can be increased to higher levels. This, however, reduces the usable dynamic range of the device. VSET AD8314 R1 5k 40mV/dB @ 1900MHz R2 5k Figure 38. Increasing the Output Slope 01086-038 V_UP EFFECT OF WAVEFORM TYPE ON INTERCEPT Although specified for input levels in dBm (dB relative to 1 mW), the AD8314 fundamentally responds to voltage and not to power. A direct consequence of this characteristic is that input signals of equal rms power but differing crest factors produces different results at the log amp's output. The effect of differing signal waveforms is to shift the effective value of the intercept upwards or downwards. Graphically, this looks like a vertical shift in the log amp's transfer function. The logarithmic slope, however, is not affected. For example, consider the case of the AD8314 being alternately fed by an unmodulated sine wave and by a single CDMA channel of the same rms power. The AD8314's output voltage differs by the equivalent of 3.55 dB (70 mV) over the complete dynamic range of the device (the output for a CDMA input being lower). Table 6 shows the correction factors that should be applied to measure the rms signal strength of various signal types. A sine wave input is used as a reference. To measure the rms power of a square wave, for example, the mV equivalent of the dB value given in the table (20 mV/dB times 3.01 dB) should be subtracted from the output voltage of the AD8314. Table 6. Shift in AD8314 Output for Signals with Differing Crest Factors Signal Type Correction Factor (Add to Measured Input Level) Sine Wave Square Wave GSM Channel (All Time Slots On) CDMA Channel (Forward Link, 9 Channels On) CDMA Channel (Reverse Link) PDC Channel (All Time Slots On) 0 dB -3.01 dB +0.55 dB +3.55 dB +0.5 dB +0.58 dB Rev. C | Page 15 of 20 AD8314 Data Sheet MOBILE HANDSET POWER CONTROL EXAMPLES Figure 39 shows a complete power amplifier control circuit for a dual mode handset. This circuit is applicable to any dual mode handset using TDMA or CDMA technologies. The PF08107B (Hitachi) is driven by a nominal power level of 3 dBm. Some of the output power from the PA is coupled off using an LDC15D190A0007A (Murata) directional coupler. This has a coupling factor of approximately 19 dB for its lower frequency band (897.5 MHz 17.5 MHz) and 14 dB for its upper band (1747.5 MHz 37.5 MHz) and an insertion loss of 0.38 dB and 0.45 dB, respectively. Because the PF08107B transmits a maximum power level of 35 dBm, additional attenuation of 15 dB is required before the coupled signal is applied to the AD8314. 3.5V The setpoint voltage, in the 0 V to 1.1 V range, is applied to the VSET pin of the AD8314. This is typically supplied by a DAC. This voltage is compared to the input level of the AD8314. Any imbalance between VSET and the RF input level is corrected by V_DN, which drives the VAPC (gain control) of the power amplifier. V_DN reaches a maximum value of approximately 1.9 V on a 2.7 V supply (this is higher for higher supply voltages) while delivering approximately 3 mA to the VAPC input. A filter capacitor (CF) must be used to stabilize the loop. The choice of CF depends to a large degree on the gain control dynamics of the power amplifier, something that is frequently characterized poorly, so some trial and error can be necessary. In this example, a 220 pF capacitor gives the loop sufficient speed to follow the GSM and DCS1800 time slot ramping profiles, while still having a stable, critically damped response. 4.7F 1000pF BAND SELECT 0V/2V POUT BAND 1 35dBm MAX TO LDC15D190A0007A ANTENNA 7 1 8 4 5 3 2 ATTN 15dB 49.9 6 PIN BAND 1 3dBm VCTL PF08107B (HITACHI) POUT BAND 2 32dBm MAX PIN BAND 2 3dBm VAPC 52.3 0.1F 0dBm MAX VS 1 RFIN VPOS 8 2 ENBL V_DN 7 VS 2.7V VSET 0V TO 1.1V 3 VSET V_UP 6 4 FLTR COMM 5 CF 220pF 01086-039 AD8314 Figure 39. A Dual Mode Power Amplifier Control Circuit Rev. C | Page 16 of 20 Data Sheet AD8314 Figure 40 shows the relationship between the setpoint voltage, VSET and output power at 0.9 GHz. The overall gain control function is linear in dB for a dynamic range of over 40 dB. 3.5V Figure 41 shows a similar circuit for a single band handset power amplifier. The BGY241 (Phillips) is driven by a nominal power level of 0 dBm. A 20 dB directional coupler, DC09-73 (Alpha), is used to couple the signal in this case. Figure 42 shows the relationship between the control voltage and the output power at 0.9 GHz. 2.2F In both of these examples, noise on the V_DN pin can be reduced by placing a simple RC low-pass filter between VDN and the gain control pin of the power amplifier. However, the value of the resistor should be kept low to minimize the voltage drop across it due to the dc current flowing into the gain control input. 47F 680pF TO ANTENNA 35dBm MAX DC09-73 4 6 15dBm ATTN 15dB BGY241 RF INPUT 5 3 1 PIN 0dBm 2 52.3 0.1F 0dBm MAX 40 VS 30 1 RFIN VPOS 8 2 ENBL V_DN 7 VS 2.7V AD8314 VSET 0V TO 1.1V 3 VSET V_UP 6 4 FLTR COMM 5 10 0 01086-041 POUT (dBm) 20 CF 220pF -10 Figure 41. A Single Mode Power Amplifier Control Circuit 40 -20 0.4 0.6 VSET (V) 0.8 1.0 1.2 Figure 40. POUT vs. VSET at 0.9 GHz for Dual Mode Handset Power Amplifier Application 20 10 0 -10 -20 -30 -40 -50 0 0.2 0.4 0.6 0.8 1.0 VSET (V) Figure 42. POUT vs. VSET at 0.9 GHz for Single Mode Handset Rev. C | Page 17 of 20 01086-042 0.2 POUT (dBm) 0 01086-040 30 -30 AD8314 Data Sheet OPERATION AT 2.7 GHz USING THE LFCSP PACKAGE While the AD8314 is specified to operate at frequencies up to 2.5 GHz, it works at higher frequencies, although it does exhibit slightly higher output voltage temperature drift. Figure 43 shows the transfer function of a typical device at 2.7 GHz, at ambient as well as hot and cold temperatures. On the underside of the LFCSP package, there is an exposed, compressed paddle. This paddle is internally connected to the chip's ground. While the paddle can be connected to the printed circuit board's ground plane, there is no thermal or electrical requirement to do this. Figure 44 shows the transfer function of the AD8314 when driven by both an unmodulated sine wave and a 64 QAM signal. As previously discussed, the higher peak-to-average ratio of the 64 QAM signal causes an increase in the intercept. EVALUATION BOARD Figure 45 shows the schematic of the AD8314 MSOP evaluation board. The layout and silkscreen of the component side are shown in Figure 46 and Figure 47. An evaluation board is also available for the LFCSP package. (For exact part numbers, see the Ordering Guide.) Apart from the slightly smaller device footprint, the LFCSP evaluation board is identical to the MSOP board. The board is powered by a single supply in the 2.7 V to 5.5 V range. The power supply is decoupled by a single 0.1 F capacitor. Additional decoupling, in the form of a series resistor or inductor in R9, can also be added. Table 7 details the various configuration options of the evaluation board. In this case, the intercept increases by approximately 1.5 dB, causing the overall transfer function to drop by the same amount. For precision operation, the AD8314 should be calibrated for each signal type that is driving it. 1.2 1.2 3 3 +25C 0.8 1 0 0.6 +80C 0 -1 64 QAM +80C 0.2 -2 0.2 0.6 0.4 -1 0.4 1 CW ERROR (dB) -40C VUP (V) -40C 2 CW ERROR (dB) +25C 0.8 -2 -60 -50 -40 -30 -20 -10 -3 10 0 0 -70 INPUT POWER (dBm) R1 0 -30 -20 -10 C1 0.1F 1 RFIN INPUT 2 ENBL SW1 R9 0 VPOS 8 VPOS V_DN 7 V_DN R4 (OPEN) AD8314 3 VSET V_UP 6 4 FLTR COMM 5 C2 (OPEN) R5 0 V_UP R6 (OPEN) R7 0 Figure 45. Evaluation Board Schematic Rev. C | Page 18 of 20 VPOS R3 0 C4 (OPEN) R8 OPEN -40 0 INPUT POWER (dBm) R2 52.3 LK1 -50 Figure 44. Shift in Transfer Function due to 64 QAM Figure 43. Operating at 2.7 GHz VSET -60 C3 (OPEN) 01086-045 0 -70 -3 10 01086-044 64 QAM 01086-043 VUP (V) 1.0 2 1.0 AD8314 01086-047 01086-046 Data Sheet Figure 46. Layout of Component Side (MSOP) Figure 47. Silkscreen of Component Side (MSOP) Table 7. Evaluation Board Configuration Options Component TP1, TP2 SW1 R1, R2 R3, R4, C2, R5, R6, C3 C1, R9 C4 R7, R8 LK1 Function Supply and Ground Vector Pins. Device Enable: When in Position A, the ENBL pin is connected to +VS and the AD8314 is in operating mode. In Position B, the ENBL pin is grounded, putting the device in power-down mode. Input Interface. The 52.3 resistor in Position R2 combines with the AD8314's internal input impedance to give a broadband input impedance of around 50 . A reactive match can be implemented by replacing R2 with an inductor and R1 (0 ) with a capacitor. Note that the AD8314's RF input is internally ac-coupled. Output Interface. R4, C2, R6, and C3 can be used to check the response of V_UP and V_DN to capacitive and resistive loading. R3/R4 and R5/R6 can be used to reduce the slope of V_UP and V_DN. Power Supply Decoupling. The nominal supply decoupling consists of a 0.1 F capacitor (C1). A series inductor or small resistor can be placed in R9 for additional decoupling. Filter Capacitor. The response time of V_UP and V_DN can be modified by placing a capacitor between FILTR and V_UP. Slope Adjust. By installing resistors in R7 and R8, the nominal slope of 20 mV/dB can be increased. See Increasing the Logarithmic Slope in Measurement Mode for more details. Measurement/Controller Mode. LK1 shorts V_UP to VSET, placing the AD8314 in measurement mode. Removing LK1 places the AD8314 in controller mode. Rev. C | Page 19 of 20 Default Condition Not Applicable SW1 = A R2 = 52.3 (Size 0603) R1 = 0 (Size 0402) R4 = C2 = R6 = C3 = Open (Size 0603) R3= R5 = 0 (Size 0603) C1 = 0.1 F (Size 0603) R9 = 0 (Size 0603) C4 = Open (Size 0603) R7 = 0 (Size 0603) R8 = Open (Size 0603) LK1 = Installed AD8314 Data Sheet OUTLINE DIMENSIONS 3.20 3.00 2.80 8 3.20 3.00 2.80 5.15 4.90 4.65 5 1 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15 MAX 1.10 MAX 0.80 0.55 0.40 0.23 0.09 6 0 0.40 0.25 10-07-2009-B 0.15 0.05 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 48. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters DETAIL A (JEDEC 95) 3.25 3.00 2.75 4 1 BOTTOM VIEW 0.50 BSC 0.05 MAX 0.02 NOM 0.30 0.23 0.18 PIN 1 INDIC ATOR AREA OPTIONS (SEE DETAIL A) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET 0.203 REF 02-13-2017-A PKG-004467 EXPOSED PAD 0.60 0.45 0.30 TOP VIEW 0.80 0.75 0.70 SEATING PLANE 0.20 MIN 8 5 2.25 2.00 1.75 PIN 1 INDEX AREA 1.89 1.74 1.59 0.55 0.40 0.30 Figure 49. 8-Lead Lead Frame Chip Scale Package [LFCSP] 2 mm x 3 mm Body and 0.75 mm Package Height (CP-8-23) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD8314ARM AD8314ARM-REEL7 AD8314ARMZ AD8314ARMZ-REEL AD8314ARMZ-REEL7 AD8314-EVAL AD8314ACPZ-RL7 AD8314ACP-EVAL AD8314ACP-EVALZ 1 2 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 8-Lead MSOP, Tube 8-Lead MSOP, 7" Tape and Reel 8-Lead MSOP, Tube 8-Lead MSOP, 13" Tape and Reel 8-Lead MSOP, 7" Tape and Reel MSOP Evaluation Board 8-Lead LFCSP, 7" Tape and Reel LFCSP Evaluation Board LFCSP Evaluation Board Z = RoHS Compliant Part. # denotes RoHS compliant product; may be top or bottom marked. (c)2002-2018 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D01086-0-1/18(C) Rev. C | Page 20 of 20 Package Option RM-8 RM-8 RM-8 RM-8 RM-8 Marking Code 2 J5A J5A J5A# J5A# J5A# Ordering Quantity 50 1,000 50 3,000 1,000 CP-8-23 0F 3,000