LTC3729 550kHz, PolyPhase, High Efficiency, Synchronous Step-Down Switching Regulator DESCRIPTION FEATURES n n n n n n n n n n n n n n n n Wide VIN Range: 4V to 36V Operation Reduces Required Input Capacitance and Power Supply Induced Noise 1% Output Voltage Accuracy Phase-Lockable Fixed Frequency: 250kHz to 550kHz True Remote Sensing Differential Amplifier PolyPhase(R) Extends from Two to Twelve Phases Reduces the Size and Value of Inductors Current Mode Control Ensures Current Sharing 1.1MHz Effective Switching Frequency (2-Phase) OPTI-LOOP(R) Compensation Reduces COUT Power Good Output Voltage Indicator Very Low Dropout Operation: 99% Duty Cycle Adjustable Soft-Start Current Ramping Internal Current Foldback Plus Shutdown Timer Overvoltage Soft-Latch Eliminates Nuisance Trips Available in 5mm x 5mm QFN and 28-Lead SSOP Packages APPLICATIONS n n n Desktop Computers/Servers Large Memory Arrays DC Power Distribution Systems L, LT, LTC, LTM, PolyPhase, OPTI-LOOP, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. The LTC (R)3729 is a multiple phase, synchronous stepdown current mode switching regulator controller that drives Nchannel external power MOSFET stages in a phaselockable fixed frequency architecture. The PolyPhase controller drives its two output stages out of phase at frequencies up to 550kHz to minimize the RMS ripple currents in both input and output capacitors. The output clock signal allows expansion for up to 12 evenly phased controllers for systems requiring 15A to 200A of output current. The multiple phase technique effectively multiplies the fundamental frequency by the number of channels used, improving transient response while operating each channel at an optimum frequency for efficiency. Thermal design is also simplified. An internal differential amplifier provides true remote sens ing of the regulated supply's positive and negative output terminals as required for high current applications. A RUN/SS pin provides both soft-start and optional timed, short-circuit shutdown. Current foldback limits MOSFET dissipation during short-circuit conditions when the overcurrent latchoff is disabled. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3729 includes a power good output pin that indicates when the output is within 7.5% of the designed set point. TYPICAL APPLICATION 0.1F LTC3729 VIN TG1 PGOOD ITH VDIFFOUT 16k - VOS VOS+ M3 S BOOST2 SW2 EAIN L1 D1 0.8H VIN 5V TO 28V SENSE1+ 16k S M2 x2 S BG1 PGND TG2 SGND 0.002 0.47F SENSE1- 1000pF S S SW1 RUN/SS 10F 35V CERAMIC x4 M1 BOOST1 0.1F 3.3k 10 S S BG2 INTVCC + SENSE2 0.002 0.47F S + S M4 x2 D2 10F + SENSE2- COUT: T510E108K004AS D1, D2: UP5840 L1, L2: CEPH149-IROMC VOUT 1.6V/40A L2 0.8H M1, M3: IRF7811W M2, M4: IRF7822 Figure 1. High Current Dual Phase Step-Down Converter COUT 1000F x2 4V 3729 TA01 3729fb 1 LTC3729 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage (VIN).......................... 36V to -0.3V Topside Driver Voltages (BOOST1,2).......... 42V to -0.3V Switch Voltage (SW1, 2)............................... 36V to -5 V SENSE1+, SENSE2+, SENSE1-, SENSE2- Voltages ..........................(1.1)INTVCC to -0.3V EAIN, VOS+, VOS-, EXTVCC, INTVCC, RUN/SS, PGOOD Voltages ........................... 7V to -0.3V Boosted Driver Voltage (BOOST-SW)............ 7V to -0.3V PLLFLTR, PLLIN, CLKOUT, PHASMD, VDIFFOUT Voltages ...............INTVCC to -0.3V for VIN 7V VDIFFOUT Voltages..............VIN - 2V to -0.3V for VIN < 7V ITH Voltage ................................................ 2.7V to -0.3V Peak Output Current <1s(TGL1,2, BG1,2)..................5A INTVCC RMS Output Current.................................. 50mA Operating Ambient Temperature Range (Note 6).......................................... -40C to 85C Junction Temperature (Note 2).............................. 125C Storage Temperature Range.................... -65C to 150C Lead Temperature (Soldering, 10 sec) (G Package Only)............................................... 300C PIN CONFIGURATION TOP VIEW PLLFLTR 5 24 VIN 32 31 30 29 28 27 26 25 24 BOOST1 23 VIN 22 BG1 PLLIN 3 6 PHASMD 7 22 EXTVCC ITH 8 21 INTVCC SGND 9 20 PGND 23 BG1 PHASMD 4 21 EXTVCC ITH 5 20 INTVCC SGND 6 19 PGND VDIFFOUT 7 NC SW2 TG2 15 PGOOD PGOOD 16 TG2 SENSE2+ SENSE2+ SENSE2- 13 9 10 11 12 13 14 15 16 SENSE2 17 SW2 - VOS+ 12 17 BOOST2 VOS+ 18 BOOST2 18 BG2 VOS- 8 NC 19 BG2 VOS- 11 14 EAIN 1 PLLFLTR 2 PLLIN VDIFFOUT 10 SW1 25 BOOST1 TG1 4 CLKOUT 26 SW1 EAIN RUN/SS 27 TG1 3 NC 2 SENSE1- SENSE1+ SENSE1+ NC RUN/SS 28 CLKOUT SENSE1- TOP VIEW 1 UH PACKAGE 32-LEAD 5mm x 5mm PLASTIC QFN JA = 34C/W EXPOSED PAD IS GND, MUST BE SOLDERED TO PCB G PACKAGE 28-LEAD PLASTIC SSOP TJMAX = 125C, JA = 95C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3729EG#PBF LTC3729EG#TRPBF LTC3729 28-Lead Plastic SSOP -40C to 85C LTC3729EUH#PBF LTC3729EUH#TRPBF 3729 32-Lead (5mm x 5mm)Plastic QFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3729fb 2 LTC3729 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 15V, VRUN/SS = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS l 0.792 0.800 0.808 V l 62 65 75 75 88 85 mV mV -5 -50 nA 0.1 -0.1 0.5 -0.5 % % 0.002 0.02 %/V 0.84 0.86 0.88 V 3 3.5 4 V Main Control Loop VEAIN Regulated Feedback Voltage (Note 3); ITH Voltage = 1.2V - = 5V VSENSEMAX Maximum Current Sense Threshold VSENSE VSENSE1, 2 = 5V IINEAIN Feedback Current (Note 3) VLOADREG Output Voltage Load Regulation (Note 3) Measured in Servo Loop; ITH Voltage = 0.7V Measured in Servo Loop; ITH Voltage = 2V VREFLNREG Reference Voltage Line Regulation VIN = 3.6V to 30V (Note 3) VOVL Output Overvoltage Threshold Measured at VEAIN UVLO Undervoltage Lockout VIN Ramping Down l l l gm Transconductance Amplifier gm ITH = 1.2V; Sink/Source 5A; (Note 3) 3 mmho gmOL Transconductance Amplifier Gain ITH = 1.2V; (gmxZL; No Ext Load); (Note 3) 1.5 V/mV IQ Input DC Supply Current Normal Mode Shutdown (Note 4) EXTVCC Tied to VOUT ; VOUT = 5V VRUN/SS = 0V 580 20 40 A A IRUN/SS Soft-Start Charge Current VRUN/SS = 1.9V -0.5 -1.2 VRUN/SS RUN/SS Pin ON Threshold VRUN/SS Rising 1.0 1.5 1.9 V VRUN/SSLO RUN/SS Pin Latchoff Arming VRUN/SS Rising from 3V 3.8 4.5 V 0.5 A ISCL RUN/SS Discharge Current Soft Short Condition VEAIN = 0.5V; VRUN/SS = 4.5V ISDLDO Shutdown Latch Disable Current VEAIN = 0.5V 2 4 A 1.6 5 A ISENSE Total Sense Pins Source Current Each Channel; VSENSE1-, 2- = VSENSE1+, 2+ = 0V -85 -60 A DFMAX Maximum Duty Factor In Dropout 98 99.5 % TG1, 2 tr TG1, 2 tf Top Gate Transition Time: Rise Time Fall Time CLOAD = 3300pF CLOAD = 3300pF 30 40 90 90 ns ns BG1, 2 tr BG1, 2 tf Bottom Gate Transition Time: Rise Time Fall Time CLOAD = 3300pF CLOAD = 3300pF 30 20 90 90 ns ns TG/BG t1D Top Gate Off to Bottom Gate On Delay CLOAD = 3300pF Each Driver Synchronous Switch-On Delay Time BG/TG t2D Bottom Gate Off to Top Gate On Delay CLOAD = 3300pF Each Driver Top Switch-On Delay Time 90 ns tON(MIN) Minimum On-Time 100 ns 90 Tested with a Square Wave (Note 5) ns Internal VCC Regulator VINTVCC Internal VCC Voltage 6V < VIN < 30V; VEXTVCC = 4V VLDO INT INTVCC Load Regulation ICC = 0 to 20mA; VEXTVCC = 4V VLDO EXT EXTVCC Voltage Drop ICC = 20mA; VEXTVCC = 5V VEXTVCC EXTVCC Switchover Voltage ICC = 20mA, EXTVCC Ramping Positive VLDOHYS EXTVCC Switchover Hysteresis ICC = 20mA, EXTVCC Ramping Negative 4.8 l 4.5 5.0 5.2 V 0.2 1.0 % 80 160 mV 4.7 V 0.2 V Oscillator and Phase-Locked Loop fNOM Nominal Frequency VPLLFLTR = 1.2V 360 400 440 kHz fLOW Lowest Frequency VPLLFLTR = 0V 230 260 290 kHz fHIGH Highest Frequency VPLLFLTR 2.4V 480 550 590 kHz RPLLIN PLLIN Input Resistance 50 k 3729fb 3 LTC3729 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 15V, VRUN/SS = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX IPLLFLTR Phase Detector Output Current Sinking Capability Sourcing Capability fPLLIN < fOSC fPLLIN > fOSC -15 15 A A RRELPHS Controller 2-Controller 1 Phase VPHASMD = 0V, Open VPHASMD = 5V 180 240 Deg Deg CLKOUT Phase (Relative to Controller 1) VPHASMD = 0V VPHASMD = Open VPHASMD = 5V 60 90 120 Deg Deg Deg CLKHIGH Clock High Output Voltage CLKLOW Clock Low Output Voltage 4 UNITS V 0.2 V 0.3 V 1 A PGOOD Output VPGL PGOOD Voltage Low IPGOOD = 2mA 0.1 IPGOOD PGOOD Leakage Current VPGOOD = 5V VPG PGOOD Trip Level, Either Controller VEAIN with Respect to Set Output Voltage VEAIN Ramping Negative VEAIN Ramping Positive -6 6 -7.5 7.5 -9.5 9.5 % % 0.995 1 1.005 V/V 46 55 dB 80 k Differential Amplifier ADA Gain CMRRDA Common Mode Rejection Ratio 0V < VCM < 5V RIN Input Resistance Measured at VOS+ Input Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formulas: LTC3729EG: TJ = TA + (PD * 95C/W) LTC3729EUH: TJ = TA + (PD * 34C/W) Note 3: The LTC3729 is tested in a feedback loop that servos VITH to a specified voltage and measures the resultant VEAIN. Note 4: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications Information. Note 5: The minimum on-time condition corresponds to the on inductor peak-to-peak ripple current 40% of IMAX (see Minimum On-Time Considerations in the Applications Information section). Note 6: The LTC3729E is guaranteed to meet performance specifications from 0C to 70C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. 3729fb 4 LTC3729 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Output Current (Figure 12) Efficiency vs Output Current (Figure 12) 100 VIN = 12V VIN = 20V 40 VOUT = 3.3V VEXTVCC = 5V IOUT = 20A f = 250kHz 20 0.1 1 10 OUTPUT CURRENT (A) VEXTVCC = 0V EFFICIENCY (%) VIN = 8V 60 80 70 50 VOUT = 3.3V f = 250kHz 10 OUTPUT CURRENT (A) 1 1000 200 SHUTDOWN 5 20 15 10 25 INPUT VOLTAGE (V) 30 5.05 200 150 100 50 0 35 0 10 30 20 CURRENT (mA) 40 4.85 4.80 EXTVCC SWITCHOVER THRESHOLD 4.75 50 25 75 0 TEMPERATURE (C) 100 125 3729 G06 Maximum Current Sense Threshold vs Percent of Nominal Output Voltage (Foldback) 75 ILOAD = 1mA 80 70 60 4.8 4.7 50 VSENSE (mV) 4.9 VSENSE (mV) INTVCC VOLTAGE (V) 4.90 4.70 -50 -25 50 5.0 25 4.6 50 40 30 20 4.5 4.4 4.95 Maximum Current Sense Threshold vs Duty Factor Internal 5V LDO Line Reg INTVCC VOLTAGE 5.00 3729 G05 3729 G04 5.1 20 INTVCC and EXTVCC Switch Voltage vs Temperature INTVCC AND EXTVCC SWITCH VOLTAGE (V) EXTVCC VOLTAGE DROP (mV) SUPPLY CURRENT (A) 400 15 3729 G03 250 ON 10 VIN (V) EXTVCC Voltage Drop 600 5 3729 G02 Supply Current vs Input Voltage and Mode 0 80 70 100 3729 G01 0 90 60 100 800 VOUT = 3.3V VEXTVCC = 5V IOUT = 20A f = 250kHz VEXTVCC = 5V 90 VIN = 5V EFFICIENCY (%) EFFICIENCY (%) 100 100 80 0 Efficiency vs Input Voltage (Figure 12) 10 0 5 20 15 25 10 INPUT VOLTAGE (V) 30 35 3729 G07 0 0 20 40 60 DUTY FACTOR (%) 80 100 3729 G08 0 50 100 0 25 75 PERCENT ON NOMINAL OUTPUT VOLTAGE (%) 3729 G09 3729fb 5 LTC3729 TYPICAL PERFORMANCE CHARACTERISTICS Maximum Current Sense Threshold vs Sense Common Mode Voltage 80 VSENSE(CM) = 1.6V Current Sense Threshold vs ITH Voltage 80 70 76 VSENSE (mV) 60 VSENSE (mV) 90 40 60 VSENSE (mV) 80 Maximum Current Sense Threshold vs VRUN/SS (Soft-Start) 72 68 50 40 30 20 10 20 0 64 -10 -20 0 0 1 2 3 4 5 60 6 1 3 4 2 COMMON MODE VOLTAGE (V) 0 VRUN/SS (V) Load Regulation FCB = 0V VIN = 15V FIGURE 1 -0.3 -0.4 VITH vs VRUN/SS 1 3 2 LOAD CURRENT (A) 4 1 1.5 VITH (V) 2 5 SENSE Pins Total Source Current VOSENSE = 0.7V 50 ISENSE (A) 1.5 1.0 0 2.5 100 0 -50 0.5 0 0.5 3729 G12 2.0 -0.1 VITH (V) NORMALIZED VOUT (%) 2.5 -0.2 0 3729 G11 3729 G10 0.0 -30 5 0 1 2 3 4 5 6 VRUN/SS (V) -100 2 0 4 6 VSENSE COMMON MODE VOLTAGE (V) 3729 G14 3729 G13 Maximum Current Sense Threshold vs Temperature 3729 G15 RUN/SS Current vs Temperature 80 1.8 1.6 RUN/SS CURRENT (A) VSENSE (mV) 78 76 74 72 1.4 1.2 1.0 0.8 0.6 0.4 0.2 70 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 3729 G17 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 3729 G19 3729fb 6 LTC3729 TYPICAL PERFORMANCE CHARACTERISTICS Soft-Start Up (Figure 12) Load Step (Figure 12) VITH 1V/DIV IOUT 0/30A VITH 1V/DIV VOUT 2V/DIV VOUT 200mV/DIV VRUNSS 2V/DIV 100ms/DIV Current Sense Pin Input Current vs Temperature EXTVCC Switch Resistance vs Temperature 31 29 27 -25 50 25 0 75 TEMPERATURE (C) 100 125 600 8 6 4 2 0 -50 -25 50 25 0 75 TEMPERATURE (C) 100 3729 G23 500 VPLLFLTR = 1.2V 400 300 VPLLFLTR = 0V 200 125 0 -50 -25 50 25 75 0 TEMPERATURE (C) 3729 G24 Undervoltage Lockout vs Temperature 100 125 3729 G25 Shutdown Latch Thresholds vs Temperature 4.5 3.50 3.45 3.40 3.35 3.30 3.25 3.20 -50 -25 VPLLFLTR = 2.4V 100 SHUTDOWN LATCH THRESHOLDS (V) 25 -50 700 FREQUENCY (kHz) EXTVCC SWITCH RESISTANCE () 33 3729 G21 Oscillator Frequency vs Temperature 10 VOUT = 5V UNDERVOLTAGE LOCKOUT (V) CURRENT SENSE INPUT CURRENT (A) 35 10s/DIV 3729 G20 50 25 75 0 TEMPERATURE (C) 100 125 3729 G26 LATCH ARMING 4.0 3.5 3.0 LATCHOFF THRESHOLD 2.5 2.0 1.5 1.0 0.5 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 3729 G27 3729fb 7 LTC3729 PIN FUNCTIONS G Package/UH Package RUN/SS (Pin 1/Pin 28): Combination of Soft-Start, Run Control Input and Short-Circuit Detection Timer. A capaci tor to ground at this pin sets the ramp time to full current output. Forcing this pin below 0.8V causes the IC to shut down all internal circuitry. All functions are disabled in shutdown. SENSE1+, SENSE2+ (Pins 2,14/Pins 30, 12): The (+) Input to the Differential Current Comparators. The ITH pin voltage and built-in offsets between SENSE- and SENSE+ pins in conjunction with RSENSE set the current trip threshold. SENSE1-, SENSE2- (Pins 3, 13/Pins 31, 11): The (-) Input to the Differential Current Comparators. EAIN (Pin 4/Pin 1): Input to the Error Amplifier that com pares the feedback voltage to the internal 0.8V reference voltage. This pin is normally connected to a resistive divider from the output of the differential amplifier (DIFFOUT). PLLFLTR (Pin 5/Pin 2): The Phase-Locked Loop's Low Pass Filter is tied to this pin. Alternatively, this pin can be driven with an AC or DC voltage source to vary the frequency of the internal oscillator. PLLIN (Pin 6/Pin 3): External Synchronization Input to Phase Detector. This pin is internally terminated to SGND with 50k. The phase-locked loop will force the rising top gate signal of controller 1 to be synchronized with the rising edge of the PLLIN signal. PHASMD (Pin 7/Pin 4): Control Input to Phase Selector which determines the phase relationships between control ler 1, controller 2 and the CLKOUT signal. ITH (Pin 8/Pin 5): Error Amplifier Output and Switching Regulator Compensation Point. Both current comparator's thresholds increase with this control voltage. The normal voltage range of this pin is from 0V to 2.4V. SGND (Pin 9/Pin 6): Signal Ground, common to both con trollers, must be routed separately from the input switched current ground path to the common (-) terminal(s) of the COUT capacitor(s). VDIFFOUT (Pin 10/Pin 7): Output of a Differential Amplifier that provides true remote output voltage sensing. This pin normally drives an external resistive divider that sets the output voltage. VOS-, VOS+ (Pins 11, 12/Pins 8, 9): Inputs to an Operational Amplifier. Internal precision resistors capable of being electronically switched in or out can configure it as a dif ferential amplifier or an uncommitted Op Amp. PGOOD (Pin 15/Pin 13): Open-Drain Logic Output. PGOOD is pulled to ground when the voltage on the EAIN pin is not within 7.5% of its set point. TG2, TG1 (Pins 16, 27/Pins 14, 26): High Current Gate Drives for Top N-Channel MOSFETS. These are the outputs of floating drivers with a voltage swing equal to INTVCC superimposed on the switch node voltage SW. SW2, SW1 (Pins 17, 26/Pins 15, 25): Switch Node Connections to Inductors. Voltage swing at these pins is from a Schottky diode (external) voltage drop below ground to VIN. BOOST2, BOOST1 (Pins 18, 25/Pins 17, 24): Bootstrapped Supplies to the Topside Floating Drivers. Capacitors are connected between the Boost and Switch pins and Schottky diodes are tied between the Boost and INTVCC pins. Voltage swing at the Boost pins is from INTVCC to (VIN + INTVCC). BG2, BG1 (Pins 19, 23/Pins 18, 22): High Current Gate Drives for Bottom Synchronous N-Channel MOSFETS. Voltage swing at these pins is from ground to INTVCC. PGND (Pin 20/Pin 19): Driver Power Ground. Connect to sources of bottom N-channel MOSFETS and the (-) terminals of CIN. INTVCC (Pin 21/Pin 20): Output of the Internal 5V Linear Low Dropout Regulator and the EXTVCC Switch. The driver and control circuits are powered from this voltage source. Decouple to power ground with a 1F ceramic capacitor placed directly adjacent to the IC and minimum of 4.7F additional tantalum or other low ESR capacitor. 3729fb 8 LTC3729 PIN FUNCTIONS G Package/UH Package EXTVCC (Pin 22/Pin 21): External Power Input to an Internal Switch . This switch closes and supplies INTVCC, bypassing the internal low dropout regulator whenever EXTVCC is higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not exceed 7V on this pin and ensure VEXTVCC VINTVCC. VIN (Pin 24/Pin 23): Main Supply Pin. Should be closely decoupled to the IC's signal ground pin. CLKOUT (Pin 28/Pin 27): Output Clock Signal available to daisychain other controller ICs for additional MOSFET driver stages/phases. FUNCTIONAL DIAGRAM PLLIN INTVCC PHASE DET FIN 50k DUPLICATE FOR SECOND CONTROLLER CHANNEL PLLLPF RLP CLKOUT CLP OSCILLATOR DROP OUT DET CLK2 PHASMD 2A PHASE LOGIC S Q R Q BOT FCB SW FORCE BOT SWITCH LOGIC INTVCC BG BOT SHDN A1 INTVCC I1 + 40k + - 0.86V SLOPE COMP EAIN - + 0.80V - + 30k SENSE + 0.86V 4(VFB) + VIN - 30k 45k EAIN 0.74V - EA + VREF - 5V LDO REG 0.80V R2 0.86V ITH CC 1.2A 6V INTERNAL SUPPLY R1 + - INTVCC + COUT VOUT 2.4V OV + RSENSE SENSE- 45k VIN 4.7V L + PGOOD SGND CIN 40k - 40k 5V + PGND 40k VOS+ EXTVCC CB TG TOP DIFFOUT VOS- DB BOOST CLK1 VIN SHDN RST 4(VFB) RUN SOFT START RC RUN/SS CSS 3729 FBD 3729fb 9 LTC3729 OPERATION (Refer to Functional Diagram) Main Control Loop Low Current Operation The LTC3729 uses a constant frequency, current mode step-down architecture. During normal operation, the top MOSFET is turned on each cycle when the oscillator sets the RS latch, and turned off when the main current comparator, I1, resets the RS latch. The peak inductor current at which I1 resets the RS latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier EA. The differential amplifier, A1, produces a signal equal to the differential voltage sensed across the output capacitor but re-references it to the internal signal ground (SGND) reference. The EAIN pin receives a portion of this voltage feedback signal at the DIFFOUT pin which is compared to the internal reference voltage by the EA. When the load current increases, it causes a slight decrease in the EAIN pin voltage relative to the 0.8V reference, which in turn causes the ITH voltage to increase until the average inductor current matches the new load current. After the top MOSFET has turned off, the bottom MOSFET is turned on for the rest of the period. The LTC3729 operates in a continuous, PWM control mode. The resulting operation at low output currents optimizes transient response at the expense of substantial negative inductor current during the latter part of the period. The level of ripple current is determined by the inductor value, input voltage, output voltage, and frequency of operation. The top MOSFET drivers are biased from floating bootstrap capacitor CB, which normally is recharged during each off cycle through an external Schottky diode. When VIN decreases to a voltage close to VOUT , however, the loop may enter dropout and attempt to turn on the top MOSFET continuously. A dropout detector detects this condition and forces the top MOSFET to turn off for about 400ns every 10th cycle to recharge the bootstrap capacitor. The main control loop is shut down by pulling Pin 1 (RUN/SS) low. Releasing RUN/SS allows an internal 1.2A current source to charge soft-start capacitor CSS. When CSS reaches 1.5V, the main control loop is enabled with the ITH voltage clamped at approximately 30% of its maximum value. As CSS continues to charge, ITH is gradually released allowing normal operation to resume. When the RUN/SS pin is low, all LTC3729 functions are shut down. If VOUT has not reached 70% of its nominal value when CSS has charged to 4.1V, an overcurrent latchoff can be invoked as described in the Applications Information section. Frequency Synchronization The phase-locked loop allows the internal oscillator to be synchronized to an external source via the PLLIN pin. The output of the phase detector at the PLLFLTR pin is also the DC frequency control input of the oscillator that operates over a 250kHz to 550kHz range corresponding to a DC voltage input from 0V to 2.4V. When locked, the PLL aligns the turn on of the top MOSFET to the rising edge of the synchronizing signal. When PLLIN is left open, the PLLFLTR pin goes low, forcing the oscillator to minimum frequency. The internal master oscillator runs at a frequency twelve times that of each controller's frequency. The PHASMD pin determines the relative phases between the internal controllers as well as the CLKOUT signal as shown in Table 1. The phases tabulated are relative to zero phase being defined as the rising edge of the top gate (TG1) driver output of controller 1. Table 1. VPHASMD GND OPEN INTVCC Controller 2 180 180 240 CLKOUT 60 90 120 The CLKOUT signal can be used to synchronize additional power stages in a multiphase power supply solution feeding a single, high current output or separate outputs. Input capacitance ESR requirements and efficiency losses are substantially reduced because the peak current drawn from the input capacitor is effectively divided by the number of phases used and power loss is proportional to the RMS current squared. A two stage, single output voltage implementation can reduce input path power loss by 75% and radically reduce the required RMS current rating of the input capacitor(s). 3729fb 10 LTC3729 OPERATION (Refer to Functional Diagram) INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most of the IC circuitry is derived from INTVCC. When the EXTVCC pin is left open, an internal 5V low dropout regulator supplies INTVCC power. If the EXTVCC pin is taken above 4.7V, the 5V regulator is turned off and an internal switch is turned on connecting EXTVCC to INTVCC. This allows the INTVCC power to be derived from a high efficiency external source such as the output of the regulator itself or a secondary winding, as described in the Applications Information section. An external Schottky diode can be used to minimize the voltage drop from EXTVCC to INTVCC in applications requiring greater than the specified INTVCC current. Voltages up to 7V can be applied to EXTVCC for additional gate drive capability. Differential Amplifier This amplifier provides true differential output voltage sensing. Sensing both VOUT+ and VOUT- benefits regulation in high current applications and/or applications having electrical interconnection losses. Power Good (PGOOD) The PGOOD pin is connected to the drain of an internal MOSFET. The MOSFET turns on when the output is not within 7.5% of its nominal output level as determined by the feedback divider. When the output is within 7.5% of its nominal value, the MOSFET is turned off within 10s and the PGOOD pin should be pulled up by an external resistor to a source of up to 7V. Short-Circuit Detection The RUN/SS capacitor is used initially to limit the inrush current from the input power source. Once the controllers have been given time, as determined by the capacitor on the RUN/SS pin, to charge up the output capacitors and provide full load current, the RUN/SS capacitor is then used as a short-circuit timeout circuit. If the output volt age falls to less than 70% of its nominal output voltage the RUN/SS capacitor begins discharging assuming that the output is in a severe overcurrent and/or short-circuit condition. If the condition lasts for a long enough period as determined by the size of the RUN/SS capacitor, the controller will be shut down until the RUN/SS pin voltage is recycled. This built-in latchoff can be overidden by providing a >5A pull-up current at a compliance of 5V to the RUN/SS pin. This current shortens the soft-start period but also prevents net discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit condition. Foldback current limiting is activated when the output voltage falls below 70% of its nominal level whether or not the short-circuit latchoff circuit is enabled. APPLICATIONS INFORMATION The basic LTC3729 application circuit is shown in Figure 1 on the first page. External component selection is driven by the load requirement, and begins with the selection of RSENSE1, 2. Once RSENSE1, 2 are known, L1 and L2 can be chosen. Next, the power MOSFETs and D1 and D2 are selected. The operating frequency and the inductor are chosen based mainly on the amount of ripple current. Finally, CIN is selected for its ability to handle the input ripple current (that PolyPhase operation minimizes) and COUT is chosen with low enough ESR to meet the output ripple voltage and load step specifications (also minimized with PolyPhase). The circuit shown in Figure 1 can be configured for operation up to an input voltage of 28V (limited by the external MOSFETs). RSENSE Selection For Output Current RSENSE1, 2 are chosen based on the required output cur rent. The LTC3729 current comparator has a maximum threshold of 75mV/RSENSE and an input common mode range of SGND to 1.1( INTVCC). The current comparator threshold sets the peak inductor current, yielding a maxi mum average output current IMAX equal to the peak value less half the peak-to-peak ripple current, IL. Allowing a margin for variations in the LTC3729 and external component values yields: RSENSE = (50mV/IMAX)N where N = number of stages. 3729fb 11 LTC3729 APPLICATIONS INFORMATION When using the controller in very low dropout conditions, the maximum output current level will be reduced due to internal slope compensation required to meet stability criterion for buck regulators operating at greater than 50% duty factor. A curve is provided to estimate this reduction in peak output current level depending upon the operating duty factor. Operating Frequency The LTC3729 uses a constant frequency, phase-lockable architecture with the frequency determined by an internal capacitor. This capacitor is charged by a fixed current plus an additional current which is proportional to the voltage applied to the PLLFLTR pin. Refer to Phase-Locked Loop and Frequency Synchronization in the Applications Infor mation section for additional information. A graph for the voltage applied to the PLLFLTR pin vs frequency is given in Figure 2. As the operating frequency is increased the gate charge losses will be higher, reducing efficiency (see Efficiency Considerations). The maximum switching frequency is approximately 550kHz. PLLFLTR PIN VOLTAGE (V) 2.5 2.0 1.5 1.0 0.5 0 200 250 300 350 400 450 500 OPERATING FREQUENCY (kHz) 550 3729 F02 Figure 2. Operating Frequency vs VPLLFLTR Inductor Value Calculation and Output Ripple Current The operating frequency and inductor selection are inter related in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET gate charge and transition losses. In addi tion to this basic tradeoff, the effect of inductor value on ripple current and low current operation must also be considered. The PolyPhase approach reduces both input and output ripple currents while optimizing individual output stages to run at a lower fundamental frequency, enhancing efficiency. The inductor value has a direct effect on ripple current. The inductor ripple current IL per individual section, N, decreases with higher inductance or frequency and increases with higher VIN or VOUT : IL = VOUT VOUT 1- fL VIN where f is the individual output stage operating frequency. In a PolyPhase converter, the net ripple current seen by the output capacitor is much smaller than the individual inductor ripple currents due to the ripple cancellation. The details on how to calculate the net output ripple current can be found in Application Note 77. Figure 3 shows the net ripple current seen by the output capacitors for the different phase configurations. The output ripple current is plotted for a fixed output voltage as the duty factor is varied between 10% and 90% on the x-axis. The output ripple current is normalized against the inductor ripple current at zero duty factor. The graph can be used in place of tedious calculations. As shown in Figure 3, the zero output ripple current is obtained when: VOUT k = VIN N where k = 1, 2, ..., N - 1 So the number of phases used can be selected to minimize the output ripple current and therefore the output ripple voltage at the given input and output voltages. In appli cations having a highly varying input voltage, additional phases will produce the best results. 3729fb 12 LTC3729 APPLICATIONS INFORMATION 1.0 0.8 0.7 0.6 VO/fL IO(P-P) ripple current and consequent output voltage ripple. Do not allow the core to saturate! 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 0.9 0.5 0.4 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 3729 F03 Figure 3. Normalized Peak Output Current vs Duty Factor [IRMS 0.3 (IO(P-P))] Accepting larger values of IL allows the use of low in ductances, but can result in higher output voltage ripple. A reasonable starting point for setting ripple current is IL = 0.4(IOUT)/N, where N is the number of channels and IOUT is the total load current. Remember, the maximum IL occurs at the maximum input voltage. The individual inductor ripple currents are constant determined by the inductor, input and output voltages. Inductor Core Selection Once the values for L1 and L2 are known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite, molypermalloy, or Kool M(R) cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore cop per losses will increase. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can con centrate on copper loss and preventing saturation. Ferrite core material saturates "hard," which means that induc tance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor Molypermalloy (from Magnetics, Inc.) is a very good, low loss core material for toroids, but it is more expensive than ferrite. A reasonable compromise from the same manufacturer is Kool M. Toroids are very space effi cient, especially when you can use several layers of wire. Because they lack a bobbin, mounting is more difficult. However, designs for surface mount are available which do not increase the height significantly. Power MOSFET, D1 and D2 Selection Two external power MOSFETs must be selected for each controller with the LTC3729: One N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5V during start-up (see EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. The only exception is if low input voltage is expected (VIN < 5V); then, sub logic-level threshold MOSFETs (VGS(TH) < 3V) should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; most of the logic-level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the "ON" resistance RDS(ON), reverse transfer capacitance CRSS, input voltage, and maximum output current. When the LTC3729 is operating in continuous mode the duty factors for the top and bottom MOSFETs of each output stage are given by: V Main Switch Duty Cycle = OUT VIN V -V Synchronous Switch Duty Cycle = IN OUT VIN The MOSFET power dissipations at maximum output current are given by: Kool M is a registered trademark of Magnetics, Inc. 3729fb 13 LTC3729 APPLICATIONS INFORMATION (1+ d )RDS(ON) + 2I k ( VIN ) MAX (CRSS ) ( f ) N V -V I PSYNC = IN OUT MAX N VIN 2 (1+ d )RDS(ON) where d is the temperature dependency of RDS(ON), k is a constant inversely related to the gate drive current and N is the number of stages. Both MOSFETs have I2R losses but the topside N-channel equation includes an additional term for transition losses, which peak at the highest input voltage. For VIN < 20V the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CRSS actual provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. The term (1 + d) is generally given for a MOSFET in the form of a normalized RDS(ON) vs. Temperature curve, but d = 0.005/C can be used as an approximation for low voltage MOSFETs. CRSS is usually specified in the MOSFET characteristics. The constant k = 1.7 can be used to estimate the contributions of the two terms in the main switch dissipation equation. The Schottky diodes, D1 and D2 shown in Figure 1 conduct during the dead-time between the conduction of the two large power MOSFETs. This helps prevent the body diode of the bottom MOSFET from turning on, storing charge during the dead-time, and requiring a reverse recovery period which would reduce efficiency. A 1A to 3A (depending on output current) Schottky diode is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. CIN and COUT Selection In continuous mode, the source current of each top Nchannel MOSFET is a square wave of duty cycle VOUT/VIN. A low ESR input capacitor sized for the maximum RMS current must be used. The details of a close form equation can be found in Application Note 77. Figure 4 shows the input capacitor ripple current for different phase configurations with the output voltage fixed and input volt age varied. The input ripple current is normalized against the DC output current. The graph can be used in place of tedious calculations. The minimum input ripple current can be achieved when the product of phase number and output voltage, N(VOUT), is approximately equal to the input voltage VIN or: VOUT k = VIN N where k = 1, 2, ..., N - 1 So the phase number can be chosen to minimize the input capacitor size for the given input and output voltages. In the graph of Figure 4, the local maximum input RMS capacitor currents are reached when: VOUT 2k - 1 = VIN 2N where k = 1, 2, ..., N 0.6 0.5 DC LOAD CURRENT 2 RMS INPUT RIPPLE CURRNET V I PMAIN = OUT MAX VIN N 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 0.4 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 3729 F04 Figure 4. Normalized Input RMS Ripple Current vs Duty Factor for 1 to 6 Output Stages These worst-case conditions are commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturer's ripple current ratings are often based on only 2000 hours of life. 3729fb 14 LTC3729 APPLICATIONS INFORMATION This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. Always consult the capacitor manufacturer if there is any question. The graph shows that the peak RMS input current is reduced linearly, inversely proportional to the number, N of stages used. It is important to note that the efficiency loss is proportional to the input RMS current squared and therefore a 2-stage implementation results in 75% less power loss when compared to a single phase design. Battery/input protection fuse resistance (if used), PC board trace and connector resistance losses are also reduced by the reduction of the input ripple current in a PolyPhase system. The required amount of input capacitance is further reduced by the factor, N, due to the effective increase in the frequency of the current pulses. The selection of COUT is driven by the required effective series resistance (ESR). Typically once the ESR require ment has been met, the RMS current rating generally far exceeds the IRIPPLE(P-P) requirements. The steady state output ripple (VOUT) is determined by: 1 VOUT IRIPPLE ESR + 8NfCOUT Where f = operating frequency of each stage, N is the number of phases, COUT = output capacitance, and IRIPPLE = combined inductor ripple currents. The output ripple varies with input voltage since IL is a function of input voltage. The output ripple will be less than 50mV at max VIN with IL = 0.4IOUT(MAX)/N assuming: COUT required ESR < 2N(RSENSE) and COUT > 1/(8Nf)(RSENSE) The emergence of very low ESR capacitors in small, surface mount packages makes very physically small implementations possible. The ability to externally compensate the switching regulator loop using the ITH pin(OPTI-LOOP compensation) allows a much wider selection of output capacitor types. OPTI-LOOP compensation effectively removes constraints on output capacitor ESR. The impedance characteristics of each capacitor type are significantly different than an ideal capacitor and therefore require accurate modeling or bench evaluation during design. Manufacturers such as Nichicon, United Chemicon and Sanyo should be considered for high performance throughhole capacitors. The OS-CON semiconductor dielectric capacitor available from Sanyo and the Panasonic SP surface mount types have the lowest (ESR)(size) product of any aluminum electrolytic at a somewhat higher price. An additional ceramic capacitor in parallel with OS-CON type capacitors is recommended to reduce the inductance effects. In surface mount applications, multiple capacitors may have to be paralleled to meet the ESR or RMS current handling requirements of the application. Aluminum electrolytic and dry tantalum capacitors are both available in surface mount configurations. New special polymer surface mount capacitors offer very low ESR also but have much lower capacitive density per unit volume. In the case of tantalum, it is critical that the capacitors are surge tested for use in switching power supplies. Several excellent choices are the AVX TPS, AVX TPSV or the KEMET T510 series of surface mount tantalums, available in case heights ranging from 2mm to 4mm. Other capacitor types include Sanyo OS-CON, Nichicon PL series and Sprague 595D series. Consult the manufacturer for other specific recommendations. A combination of capacitors will often result in maximizing performance and minimizing overall cost and size. INTVCC Regulator An internal P-channel low dropout regulator produces 5V at the INTVCC pin from the VIN supply pin. The INTVCC regulator powers the drivers and internal circuitry of the LTC3729. The INTVCC pin regulator can supply up to 50mA peak and must be bypassed to power ground with a minimum of 4.7F tantalum or electrolytic capacitor. An additional 1F ceramic capacitor placed very close to the IC is recommended due to the extremely high instantaneous currents required by the MOSFET gate drivers. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the 3729fb 15 LTC3729 APPLICATIONS INFORMATION maximum junction temperature rating for the LTC3729 to be exceeded. The supply current is dominated by the gate charge supply current, in addition to the current drawn from the differential amplifier output. The gate charge is dependent on operating frequency as discussed in the Efficiency Considerations section. The supply current can either be supplied by the internal 5V regulator or via the EXTVCC pin. When the voltage applied to the EXTVCC pin is less than 4.7V, all of the INTVCC load current is supplied by the internal 5V linear regulator. Power dissipation for the IC is higher in this case by (IIN)(VIN - INTVCC) and efficiency is lowered. The junction temperature can be estimated by using the equations given in Note 1 of the Electrical Characteristics. For example, the LTC3729 VIN current is limited to less than 24mA from a 24V supply: TJ = 70C + (24mA)(24V)(95C/W) = 125C Use of the EXTVCC pin reduces the junction temperature to: TJ = 70C + (24mA)(5V)(95C/W) = 81.4C The input supply current should be measured while the controller is operating in continuous mode at maximum VIN and the power dissipation calculated in order to prevent the maximum junction temperature from being exceeded. EXTVCC Connection The LTC3729 contains an internal P-channel MOSFET switch connected between the EXTVCC and INTVCC pins. When the voltage applied to EXTVCC rises above 4.7V, the internal regulator is turned off and the switch closes, connecting the EXTVCC pin to the INTVCC pin thereby supplying internal and MOSFET gate driving power. The switch remains closed as long as the voltage applied to EXTVCC remains above 4.5V. This allows the MOSFET driver and control power to be derived from the output during normal operation (4.7V < VEXTVCC < 7V) and from the internal regulator when the output is out of regulation (start-up, short-circuit). Do not apply greater than 7V to the EXTVCC pin and ensure that EXTVCC < VIN + 0.3V when using the application circuits shown. If an external voltage source is applied to the EXTVCC pin when the VIN supply is not present, a diode can be placed in series with the LTC3729's VIN pin and a Schottky diode between the EXTVCC and the VIN pin, to prevent current from backfeeding VIN. Significant efficiency gains can be realized by powering INTVCC from the output, since the VIN current resulting from the driver and control currents will be scaled by the ratio: (Duty Factor)/(Efficiency). For 5V regulators this means connecting the EXTVCC pin directly to VOUT . However, for 3.3V and other lower voltage regulators, additional circuitry is required to derive INTVCC power from the output. The following list summarizes the four possible connec tions for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from the internal 5V regulator resulting in a significant efficiency penalty at high input voltages. 2. EXTVCC connected directly to VOUT. This is the normal connection for a 5V regulator and provides the highest efficiency. 3. EXTVCC connected to an external supply. If an external supply is available in the 5V to 7V range, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. VIN must be greater than or equal to the voltage applied to the EXTVCC pin. 4. EXTVCC connected to an output-derived boost network. For 3.3V and other low voltage regulators, efficiency gains can still be realized by connecting EXTVCC to an outputderived voltage which has been boosted to greater than 4.7V but less than 7V. This can be done with either the inductive boost winding as shown in Figure 5a or the capacitive charge pump shown in Figure 5b. The charge pump has the advantage of simple magnetics. Topside MOSFET Driver Supply (CB,DB) (Refer to Functional Diagram) External bootstrap capacitors CB1 and CB2 connected to the BOOST1 and BOOST2 pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though diode DB from INTVCC when the SW pin is low. When the topside MOSFET turns on, the driver places the CB voltage across the 3729fb 16 LTC3729 APPLICATIONS INFORMATION OPTIONAL EXTVCC CONNECTION 5V < VSEC < 7V + CIN LTC3729 VIN CIN VIN LTC3729 1N4148 EXTVCC + 6.8V N-CH T1 BG1 BAT85 N-CH 1mF + 0.22F 1F BAT85 VOUT SW1 COUT BG1 BAT85 VN2222LL EXTVCC RSENSE SW1 VIN + VIN TG1 VSEC TG1 + RSENSE L1 VOUT + COUT N-CH N-CH PGND PGND 3729 F05b 3729 F05a Figure 5a. Secondary Output Loop and EXTVCC Connection gate-source of the desired MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VIN and the BOOST pin rises to VIN + VINTVCC. The value of the boost capacitor CB needs to be 30 to 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of DB must be greater than VIN(MAX). The final arbiter when defining the best gate drive amplitude level will be the input supply current. If a change is made that decreases input current, the efficiency has improved. If the input current does not change then the efficiency has not changed either. Differential Amplifier/Output Voltage The LTC3729 has a true remote voltage sense capablity. The sensing connections should be returned from the load back to the differential amplifier's inputs through a common, tightly coupled pair of PC traces. The differential amplifier rejects common mode signals capacitively or inductively radiated into the feedback PC traces as well as ground loop disturbances. The differential amplifier output signal is divided down and compared with the internal precision 0.8V voltage reference by the error amplifier. The differential amplifier utilizes a set of internal preci sion resistors to enable precision instrumentation-type measurement of the output voltage. The output is an NPN emitter follower without any internal pull-down current. A DC resistive load to ground is required in order to sink Figure 5b. Capacitive Charge Pump for EXTVCC current. The output voltage is set by an external resistive divider according to the following formula: R1 VOUT = 0.8V 1+ R2 where R1 and R2 are defined in the Functional Diagram. Soft-Start/Run Function The RUN/SS pin provides three functions: 1) Run/Shut down, 2) soft-start and 3) a defeatable short-circuit latchoff timer. Soft-start reduces the input power sources' surge currents by gradually increasing the controller's current limit ITH(MAX). The latchoff timer prevents very short, ex treme load transients from tripping the overcurrent latch. A small pull-up current (>5A) supplied to the RUN/SS pin will prevent the overcurrent latch from operating. The following explanation describes how the functions operate. An internal 1.2A current source charges up the CSS capacitor. When the voltage on RUN/SS reaches 1.5V, the controller is permitted to start operating. As the voltage on RUN/SS increases from 1.5V to 3.0V, the internal current limit is increased from 25mV/RSENSE to 75mV/RSENSE. The output current limit ramps up slowly, taking an ad ditional 1.4s/F to reach full current. The output current thus ramps up slowly, reducing the starting surge current required from the input power supply. If RUN/SS has been 3729fb 17 LTC3729 APPLICATIONS INFORMATION pulled all the way to ground there is a delay before starting of approximately: 1.5V t DELAY = C = (1.25s / F ) CSS 1.2A SS VIN 3.3V OR 5V D1 INTVCC RUN/SS RSS* RSS* D1* The time for the output current to ramp up is then: t RAMP = 3V - 1.5V C = (1.25s / F ) CSS 1.2A SS By pulling the RUN/SS pin below 0.8V the LTC3729 is put into low current shutdown (IQ < 40A). RUN/SS can be driven directly from logic as shown in Figure 6. Diode D1 in Figure 6 reduces the start delay but allows CSS to ramp up slowly providing the soft-start function. The RUN/SS pin has an internal 6V zener clamp (see Functional Diagram). Fault Conditions: Overcurrent Latchoff The RUN/SS pin also provides the ability to latch off the controllers when an overcurrent condition is detected. The RUN/SS capacitor, CSS, is used initially to limit the inrush current of both controllers. After the controllers have been started and been given adequate time to charge up the output capacitors and provide full load current, the RUN/SS capacitor is used for a short-circuit timer. If the output voltage falls to less than 70% of its nominal value after CSS reaches 4.1V, CSS begins discharging on the as sumption that the output is in an overcurrent condition. If the condition lasts for a long enough period as determined by the size of CSS, the controller will be shut down until the RUN/SS pin voltage is recycled. If the overload occurs during start-up, the time can be approximated by: tLO1 (CSS * 0.6V)/(1.2A) = 5 * 105 (CSS) If the overload occurs after start-up, the voltage on CSS will continue charging and will provide additional time before latching off: tLO2 (CSS * 3V)/(1.2A) = 2.5 * 106 (CSS) This built-in overcurrent latchoff can be overridden by providing a pull-up resistor, RSS, to the RUN/SS pin as shown in Figure 6. This resistance shortens the softstart period and prevents the discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit RUN/SS CSS CSS *OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF 3729 F06 Figure 6. RUN/SS Pin Interfacing condition. When deriving the 5A current from VIN as in the figure, current latchoff is always defeated. Diodeconnecting this pull-up resistor to INTVCC, as in Figure 6, eliminates any extra supply current during shutdown while eliminating the INTVCC loading from preventing controller start-up. Why should you defeat current latchoff? During the pro totyping stage of a design, there may be a problem with noise pickup or poor layout causing the protection circuit to latch off the controller. Defeating this feature allows troubleshooting of the circuit and PC layout. The internal short-circuit and foldback current limiting still remains active, thereby protecting the power supply system from failure. A decision can be made after the design is com plete whether to rely solely on foldback current limiting or to enable the latchoff feature by removing the pull-up resistor. The value of the soft-start capacitor CSS may need to be scaled with output voltage, output capacitance and load current characteristics. The minimum soft-start capacitance is given by: CSS > (COUT )(VOUT)(10-4)(RSENSE) The minimum recommended soft-start capacitor of CSS = 0.1F will be sufficient for most applications. Phase-Locked Loop and Frequency Synchronization The LTC3729 has a phase-locked loop comprised of an internal voltage controlled oscillator and phase detector. This allows the top MOSFET turn-on to be locked to the rising edge of an external source. The frequency range of the voltage controlled oscillator is 50% around the center frequency fO. A voltage applied to the PLLFLTR pin of 1.2V corresponds to a frequency of approximately 3729fb 18 LTC3729 APPLICATIONS INFORMATION 400kHz. The nominal operating frequency range of the LTC3729 is 250kHz to 550kHz. The phase detector used is an edge sensitive digital type which provides zero degrees phase shift between the ex ternal and internal oscillators. This type of phase detector will not lock up on input frequencies close to the harmonics of the VCO center frequency. The PLL hold-in range, fH, is equal to the capture range, fC: fH = fC = 0.5 fO (250kHz-550kHz) The output of the phase detector is a complementary pair of current sources charging or discharging the external filter network on the PLLFLTR pin. A simplified block diagram is shown in Figure 7. 2.4V PHASE DETECTOR EXTERNAL OSC RLP 10k CLP PLLFLTR PLLIN 50k DIGITAL PHASE/ FREQUENCY DETECTOR a voltage that will guarantee the slave oscillator(s) ability to lock onto the master's frequency. A DC voltage of 0.7V to 1.7V applied to the master oscillator's PLLFLTR pin is recommended in order to meet this requirement. The resultant operating frequency will be approximately 500kHz. The loop filter components (CLP, RLP) smooth out the cur rent pulses from the phase detector and provide a stable input to the voltage controlled oscillator. The filter compo nents CLP and RLP determine how fast the loop acquires lock. Typically RLP =10k and CLP is 0.01F to 0.1F. Minimum On-Time Considerations Minimum on-time tON(MIN) is the smallest time duration that the LTC3729 is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: OSC t ON(MIN ) < 3729 F07 Figure 7. Phase-Locked Loop Block Diagram If the external frequency (fPLLIN) is greater than the os cillator frequency f0SC, current is sourced continuously, pulling up the PLLFLTR pin. When the external frequency is less than f0SC, current is sunk continuously, pulling down the PLLFLTR pin. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. Thus the voltage on the PLLFLTR pin is adjusted until the phase and frequency of the ex ternal and internal oscillators are identical. At this stable operating point the phase comparator output is open and the filter capacitor CLP holds the voltage. The LTC3729 PLLIN pin must be driven from a low impedance source such as a logic gate located close to the pin. When us ing multiple LTC3729's for a phase-locked system, the PLLFLTR pin of the master oscillator should be biased at VOUT VIN ( f ) If the duty cycle falls below what can be accommodated by the minimum on-time, the LTC3729 will begin to skip cycles resulting in nonconstant frequency operation. The output voltage will continue to be regulated, but the ripple current and ripple voltage will increase. The minimum on-time for the LTC3729 is approximately 100ns. However, as the peak sense voltage decreases the minimum on-time gradually increases. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with cor respondingly larger current and voltage ripple. If an application can operate close to the minimum on-time limit, an inductor must be chosen that has a low enough inductance to provide sufficient ripple amplitude to meet the minimum on-time requirement. As a general rule, keep the inductor ripple current of each phase equal to or greater than 15% of IOUT(MAX)/N at VIN(MAX). 3729fb 19 LTC3729 APPLICATIONS INFORMATION Voltage Positioning Voltage positioning can be used to minimize peak-to-peak output voltage excursions under worst-case transient loading conditions. The open-loop DC gain of the control loop is reduced depending upon the maximum load step specifications. Voltage positioning can easily be added to the LTC3729 by loading the ITH pin with a resistive divider having a Thevenin equivalent voltage source equal to the midpoint operating voltage range of the error amplifier, or 1.2V (see Figure 8). 2) INTVCC regulator current, 3) I2R losses and 4) Topside MOSFET transition losses. 1) The VIN current has two components: the first is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents; the second is the current drawn from the differential amplifier output. VIN current typically results in a small (<0.1%) loss. Figure 8. Active Voltage Positioning Applied to the LTC3729 2) INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge dQ moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit cur rent. In continuous mode, IGATECHG = (QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. The resistive load reduces the DC loop gain while main taining the linear control range of the error amplifier. The maximum output voltage deviation can theoretically be reduced to half or alternatively the amount of output capacitance can be reduced for a particular application. A complete explanation is included in Design Solutions 10. (See www.linear-tech.com) Supplying INTVCC power through the EXTVCC switch input from an output-derived source will scale the VIN current required for the driver and control circuits by the ratio (Duty Factor)/(Efficiency). For example, in a 20V to 5V application, 10mA of INTVCC current results in approximately 3mA of VIN current. This reduces the mid-current loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. INTVCC RT2 ITH RT1 RC LTC3729 CC 3729 F08 Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percent age of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3729 circuits: 1) LTC3729 VIN current (including loading on the differential amplifier output), 3) I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor, and input and output capacitor ESR. In continuous mode the average output current flows through L and RSENSE, but is "chopped" between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For example, if each RDS(ON)=10m, RL=10m, and RSENSE=5m, then the total resistance is 25m. This results in losses ranging from 2% to 8% as the output current increases from 3A to 15A per output stage for a 5V output, or a 3% to 12% loss per output stage for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects 3729fb 20 LTC3729 APPLICATIONS INFORMATION of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 4) Transition losses apply only to the topside MOSFET(s), and only when operating at high input voltages (typically 20V or greater). Transition losses can be estimated from: Transition Loss = (1.7) VIN2 IO(MAX) CRSS f Other "hidden" losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these "system" level losses in the design of a system. The internal battery and input fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and a very low ESR at the switching frequency. A 50W supply will typically require a minimum of 200F to 300F of capacitance having a maximum of 10m to 20m of ESR. The LTC3729 PolyPhase architecture typically halves to quarters this input capacitance requirement over competing solutions. Other losses including Schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by look ing at the load transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ILOAD(ESR), where ESR is the effective series resistance of COUT(ILOAD) also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. The availability of the ITH pin not only allows optimization of control loop behavior but also provides a DC coupled and AC filtered closed loop response test point. The DC step, rise time, and settling at this test point truly reflects the closed loop response. Assuming a predominantly second order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in the Figure 1 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.2 to 5 times their suggested values) to maximize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be decided upon because the various types and values determine the loop feedback factor gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of <2s will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the Ith pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be in creased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. A second, more severe transient is caused by switching in loads with large (>1F) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT , causing a rapid drop in VOUT . No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 * CLOAD. Thus a 10F capacitor would require a 250s rise time, limiting the charging current to about 200mA. 3729fb 21 LTC3729 APPLICATIONS INFORMATION Design Example (Using Two Phases) As a design example, assume VIN = 5V (nominal), VIN = 5.5V (max), VOUT = 1.8V, IMAX = 20A, TA = 70C and f = 300kHz. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the PLLFLTR pin to a resistive divider using the INTVCC pin to generate 1V for 300kHz operation. The minimum inductance for 30% ripple current is: L VOUT VOUT 1- f ( I) VIN 1.8V 1.8V 1- (300kHz )(30%)(10A ) 5.5V 1.35H A 2H inductor will produce 20% ripple current. The peak inductor current will be the maximum DC value plus one half the ripple current, or 11.5A. The minimum on-time occurs at maximum VIN: V 1.8V tON(MIN ) = OUT = = 1.1s VIN f ( 5.5V ) ( 300kHz ) The RSENSE resistors value can be calculated by using the maximum current sense voltage specification with some accomodation for tolerances: RSENSE = 50mV 0.005 11.5A Choosing 1% resistors: R1 = 16.5k and R2 = 13.2k yields an output voltage of 1.80V. The power dissipation on the topside MOSFET can be easily estimated. Using a Siliconix Si4420DY for example; RDS(ON) = 0.013, CRSS = 300pF. At maximum input voltage with Tj (estimated) = 110C at an elevated ambient temperature: PMAIN = 1.8V 2 10 ) 1+ ( 0.005) (110C - 25C) ( 5.5V 0.013 + 1.7 ( 5.5V ) (10A ) ( 300pF ) 2 (310kHz )= 0.61W The worst-case power disipated by the synchronous MOSFET under normal operating conditions at elevated ambient temperature and estimated 50C junction temperature rise is: PSYNC = 5.5V - 1.8V 2 10A ) (1.48 ) ( 0.013 ) ( 5.5V = 1.29W A short-circuit to ground will result in a folded back current of: 25mV 1 200ns ( 5.5V ) I SC = + = 5.28A 0.005 2 2H The worst-case power disipated by the synchronous MOSFET under short-circuit conditions at elevated ambi ent temperature and estimated 50C junction temperature rise is: PSYNC = 5.5V - 1.8V 2 5.28A ) (1.48 ) ( 0.013 ) ( 5.5V = 360mW 3729fb 22 LTC3729 APPLICATIONS INFORMATION which is much less than normal, full-load conditions. Incidentally, since the load no longer dissipates power in the shorted condition, total system power dissipation is decreased by over 99%. The duty cycles when the peak RMS input current occurs is at D = 0.25 and D = 0.75 according to Figure 4. Calculate the worst-case required RMS input current rating at the input voltage, which is 5.5V, that provides a duty cycle nearest to the peak. From Figure 4, CIN will require an RMS current rating of: CIN requiredIRMS = ( 20A ) ( 0.23) = 4.6ARMS The output capacitor ripple current is calculated by using the inductor ripple already calculated for each inductor and multiplying by the factor obtained from Figure 3 along with the calculated duty factor. The output ripple in continuous mode will be highest at the maximum input voltage. From Figure 3, the maximum output current ripple is: VOUT (0.34) fL 1.8 ( 0.34) ICOUTMAX = = 1A (300kHz )(2H) ICOUT = Note that the PolyPhase technique will have its maximum benefit for input and output ripple currents when the number of phases times the output voltage is approximately equal to or greater than the input voltage. PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3729. These items are also illustrated graphically in the layout diagram of Figure 11. Check the following in your layout: 1) Are the signal and power grounds segregated? The LTC3729 signal ground pin should return to the (-) plate of COUT separately. The power ground returns to the sources of the bottom N-channel MOSFETs, anodes of the Schottky diodes, and (-) plates of CIN, which should have as short lead lengths as possible. 2) Does the LTC3729 VOS+ pin connect to the (+) plate(s) of COUT? Does the LTC3729 VOS- pin connect to the (-) plate(s) of COUT? The resistive divider R1, R2 must be connected between the VDIFFOUT and signal ground and any feedforward capacitor across R1 should be as close as possible to the LTC3729. 3) Are the SENSE- and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitors between SENSE+ and SENSE- pin pairs should be as close as possible to the LTC3729. Ensure accurate current sensing with Kelvin connections to the sense resistors. 4) Do the (+) plates of CIN connect to the drains of the topside MOSFETs as closely as possible? This capacitor provides the AC current to the MOSFETs. Keep the input current path formed by the input capacitor, top and bottom MOSFETs, and the Schottky diode on the same side of the PC board in a tight loop to minimize conducted and radiated EMI. 5) Is the INTVCC 1F ceramic decoupling capacitor con nected closely between INTVCC and the power ground pin? This capacitor carries the MOSFET driver peak currents. A small value is used to allow placement immediately adjacent to the IC. 6) Keep the switching nodes, SW1 (SW2), away from sen sitive small-signal nodes. Ideally the switch nodes should be placed at the furthest point from the LTC3729. 7) Use a low impedance source such as a logic gate to drive the PLLIN pin and keep the lead as short as possible. 8) Minimize the capacitive load on the CLKOUT pin to minimize excess phase shift. Buffer if necessary with an NPN emitter follower. 3729fb 23 LTC3729 APPLICATIONS INFORMATION The diagram in Figure 9 illustrates all branch currents in a 2-phase switching regulator. It becomes very clear after studying the current waveforms why it is critical to keep the high-switching-current paths to a small physical size. High electric and magnetic fields will radiate from these "loops" just as radio stations transmit signals. The output capacitor ground should return to the negative terminal of the input capacitor and not share a common ground path with any switched current paths. The left half of the circuit gives rise to the "noise" generated by a switching regulator. The ground terminations of the sychronous MOSFETs and Schottky diodes should return to the bottom plate(s) of the SW1 input capacitor(s) with a short isolated PC trace since very high switched currents are present. A separate isolated path from the bottom plate(s) of the input capacitor(s) should be used to tie in the IC power ground pin (PGND) and the signal ground pin (SGND). This technique keeps inherent signals generated by high current pulses from taking alternate current paths that have finite impedances during the total period of the switching regulator. External OPTI-LOOP compensation allows overcompensation for PC layouts which are not optimized but this is not the recommended design procedure. L1 RSENSE1 D1 VIN VOUT RIN CIN + + SW2 L2 COUT RL RSENSE2 D2 BOLD LINES INDICATE HIGH, SWITCHING CURRENT LINES. KEEP LINES TO A MINIMUM LENGTH. 3729 F09 Figure 9. Instantaneous Current Path Flow in a Multiple Phase Switching Regulator 3729fb 24 LTC3729 APPLICATIONS INFORMATION Simplified Visual Explanation of How a 2-Phase Controller Reduces Both Input and Output RMS Ripple Current A multiphase power supply significantly reduces the amount of ripple current in both the input and output capacitors. The RMS input ripple current is divided by, and the effective ripple frequency is multiplied up by the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by, and the effective ripple frequency is increased by the number of phases used. Figure 10 graphically illustrates the principle. illustrate how the input and output currents are reduced by using an additional phase. The input current peaks drop in half and the frequency is doubled for a 2-phase converter. The input capacity requirement is reduced theoretically by a factor of four! A ceramic input capacitor with its unbeatably low ESR characteristic can be used. Figure 4 illustrates the RMS input current drawn from the input capacitance versus the duty cycle as determined by the ratio of input and output voltage. The peak input RMS current level of the single phase system is reduced by 50% in a 2-phase solution due to the current splitting between the two stages. An interesting result of the multi-phase solution is that the VIN which produces worst-case ripple current for the input capacitor, VOUT = VIN/2, in the single phase design produces zero input current ripple in the 2-phase design. SINGLE PHASE SW V ICIN The output ripple current is reduced significantly when compared to the single phase solution using the same inductance value because the VOUT/L discharge current term from the stage(s) that has its bottom MOSFET on subtracts current from the (VIN - VOUT)/L charging current resulting from the stage which has its top MOSFET on. The output ripple current is: ICOUT DUAL PHASE SW1 V SW2 V IL1 IRIPPLE = IL2 2VOUT 1- 2D (1-D) fL 1- 2D + 1 where D is duty factor. ICIN ICOUT RIPPLE 3729 F10 Figure 10. Single and PolyPhase Current Waveforms The worst-case RMS ripple current for a single stage design peaks at twice the value of the output voltage . The worstcase RMS ripple current for a two stage design results in peaks at 1/4 and 3/4 of input voltage. When the RMS cur rent is calculated, higher effective duty factor results and the peak current levels are divided as long as the currents in each stage are balanced. Refer to Application Note 19 for a detailed description of how to calculate RMS current for the single stage switching regulator. Figures 3 and 4 help to The input and output ripple frequency is increased by the number of stages used, reducing the output capacity requirements. When VIN is approximately equal to NVOUT as illustrated in Figures 3 and 4, very low input and output ripple currents result. Again, the interesting result of 2-phase operation results in no output ripple at VOUT = VIN/2. The addition of more phases by phase locking additional controllers always results in no net input or output ripple at VOUT/VIN ratios equal to the number of stages implemented. Designing a system with a multiple of stages close to the VOUT/VIN ratio will significantly reduce the ripple voltage at the input and outputs and thereby improve efficiency, physical size, and heat generation of the overall switching power supply. 3729fb 25 LTC3729 TYPICAL APPLICATIONS OPTIONAL SYNC CLOCK IN L1 2 3 8.06k, 1% 4 5 6 0.3F 6800pF 100pF 25.5k, 1% 47k 8 9 10 11 12 470pF 13 14 SENSE1+ CLKOUT TG1 - SENSE1 EAIN SW1 BOOST1 PLLFLTR PLLIN LTC3729 VIN BG1 PHASMD EXTVCC ITH INTVCC SGND PGND VDIFFOUT VOS- VOS+ BG2 BOOST2 SW2 SENSE2- TG2 SENSE2+ PGOOD 27 0.47F 26 25 M1 D7 24 23 22 21 M2 1F 5V 1F,6.3V 20 22F 6.3V GND 17 D8 16 0.47F 15 3X330F, 6.3V POSCAP VOUT 3.3V/90A 18 M4 M5 M6 D2 MBRS 340T3 L2 0.003 L3 2 4 10k 5 6 1nF SENSE1+ CLKOUT 0.003 TG1 SENSE1- EAIN SW1 BOOST1 PLLFLTR PLLIN LTC3729 EXTVCC PHASMD 8 I 100pF 9 TH SGND 10 NC V 11 DIFFOUT V - 12 OS+ V 13 OS SENSE2- 14 SENSE2+ VIN BG1 INTVCC PGND BG2 BOOST2 SW2 TG2 PGOOD 27 0.47F 26 25 M7 D9 24 23 22 21 M8 10 1F,6.3V 20 22F 6.3V 3 4 10k 5 6 1nF TG1 SENSE1- EAIN SW1 BOOST1 PLLFLTR PLLIN LTC3729 PHASMD 8 I 100pF 9 TH SGND 10 NC V 11 DIFFOUT V - 12 OS+ V 13 OS SENSE2- 14 SENSE2+ VIN BG1 EXTVCC INTVCC PGND BG2 BOOST2 SW2 TG2 PGOOD 17 D10 16 0.47F 15 M10 M11 M12 27 0.47F 26 25 0.003 L5 0.003 M13 D11 24 23 22 21 M14 M15 10 D5 MBRS 340T3 3X330F, 6.3V 1F 5V VIN 12V D4 MBRS 340T3 L4 28 1F,6.3V 20 22F 6.3V 2X150F 16V GND POSCAP 19 18 17 16 15 D12 0.47F M16 1000pF VIN: 12V VOUT: 3.3V/90A SWITCHING FREQUENCY = 400kHz POSCAP + 7 SENSE1+ CLKOUT GND 18 + 2 RUN/SS 2X150F 16V 19 + 1 D3 MBRS 340T3 3X330F, 6.3V 1F 5V 1000pF 1000pF M9 + 7 RUN/SS 28 + 1 3 0.01F 2X150F 16V 19 + 1000pF 47pF D1 MBRS 340T3 75k 24k 0.01F M3 10 1000pF 47pF 0.003 28 + 7 RUN/SS + 0.33F 1 + 1000pF M17 L6 MI - M18: Si7440DP L1 - L6: 1H PANASONIC ETQP6F1R0S D7 - D12: CENTROL CMDSH-3TR M18 D6 MBRS 340T3 0.003 OUTPUT CAPACITORS: SANYO 6TPB330M 3729 TA03 Figure 11. High Current 3.3V/90A 6-Phase Application 3729fb 26 LTC3729 PACKAGE DESCRIPTION (For purposes of clarity, drawings are not to scale) G Package 28-Lead Plastic SSOP (5.3mm) (Reference LTC DWG # 05-08-1640) 9.90 - 10.50* (.390 - .413) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1.25 0.12 7.8 - 8.2 5.3 - 5.7 0.42 0.03 7.40 - 8.20 (.291 - .323) 0.65 BSC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 RECOMMENDED SOLDER PAD LAYOUT 2.0 (.079) MAX 5.00 - 5.60** (.197 - .221) 0 - 8 0.09 - 0.25 (.0035 - .010) 0.55 - 0.95 (.022 - .037) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 0.65 (.0256) BSC 0.22 - 0.38 (.009 - .015) TYP 0.05 (.002) MIN G28 SSOP 0204 3. DRAWING NOT TO SCALE *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED .152mm (.006") PER SIDE **DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE 3729fb 27 LTC3729 PACKAGE DESCRIPTION (For purposes of clarity, drawings are not to scale) UH Package 32-Lead Plastic QFN (5mm x 5mm) (Reference LTC DWG # 05-08-1693 Rev D) 0.70 0.05 5.50 0.05 4.10 0.05 3.50 REF (4 SIDES) 3.45 0.05 3.45 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 0.10 (4 SIDES) BOTTOM VIEW--EXPOSED PAD 0.75 0.05 R = 0.05 TYP 0.00 - 0.05 R = 0.115 TYP PIN 1 NOTCH R = 0.30 TYP OR 0.35 x 45 CHAMFER 31 32 0.40 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 3.50 REF (4-SIDES) 3.45 0.10 3.45 0.10 (UH32) QFN 0406 REV D 0.200 REF NOTE: 1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE M0-220 VARIATION WHHD-(X) (TO BE APPROVED) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 0.05 0.50 BSC 3729fb 28 LTC3729 REVISION HISTORY (Revision history begins at Rev B) REV DATE DESCRIPTION PAGE NUMBER B 03/11 Updated Absolute Maximum Ratings section 2 Replaced Graph G09 5 Updated text and equation in Differential Amplifier/Output Voltage section 17 Updated Figure 11, Figure 12 Updated Related Parts 26, 30 30 3729fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. 29 LTC3729 TYPICAL APPLICATION L1 3 4 5 13.2k 6 33pF 1000pF 8 9 16.5k 10 11 12 100pF 13 14 TG1 - SENSE1 SW1 EAIN BOOST1 PLLFLTR VIN BG1 PLLIN EXTVCC PHASMD ITH LTC3729 SGND VDIFFOUT VOS- INTVCC PGND BG2 BOOST2 VOS+ SENSE2- SENSE2+ SW2 TG2 PGOOD 27 0.47F 26 25 M1 D3 24 10 23 22 21 0.1F 5V 1F,6.3V 20 D1 UPS840 CIN 4.7F 6.3V COUT 19 18 D4 17 16 100k 0.47F 15 POWER GOOD 1000pF VIN: 5V TO 16V VOUT: 3.3V/30A SWITCHING FREQUENCY = 250kHz M2 + 3.3k 7 SENSE1+ 0.003 28 + 2 0.1F CLKOUT RUN/SS + 1 1000pF D2 UPS840 M3 M4 L2 MI, M3: IRF7811 M2, M4: IRF7809 L1, L2: 1H SUMIDA CEP125-1R0MC-H VIN 6V TO 16V 0.003 VOUT 3.3V/30A CIN: OS CON 2-16SP270M COUT: KEMET 3-T510 470mF D3, D4: CENTRAL CMDSH-3TR 3729TA02 Figure 12. 3.3V/30A Power Supply with Active Voltage Positioning RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3856 Single Output 2-Channel Polyphase Synchronous Step-Down DC/DC Controller with Diff Amp and up to 12-Phase Operation PLL Fixed 250kHz to 770kHz Frequency, 4.5V VIN 38V, 0.8V VOUT 5V LTC3880/LTC3880-1 Dual Output PolyPhase Step-Down DC/DC Controller with Digital Power System Management LTC3829 Single Output 3-Channel Polyphase Synchronous Step-Down DC/DC Controller with Diff Amp and up to 6-Phase Operation I2C/PMBus Interface with EEPROM and 16-Bit ADC, VIN Up to 24V, 0.5V VOUT 5.5V, Analog Control Loop PLL Fixed 250kHz to 770kHz Frequency, 4.5V VIN 38V, 0.8V VOUT 5V LTC3869/LTC3869-2 Dual Output, 2-Phase Synchronous Step-Down DC/DC Controller, with Accurate Current Share PLL Fixed 250kHz to 750kHz Frequency, 4V VIN 38V, VOUT3 Up to 12.5V LTC3850/LTC3850-1 Dual Output, 2-Phase Synchronous Step-Down DC/DC LTC3850-2 Controller, RSENSE or DCR Current Sensing PLL Fixed 250kHz to 780kHz Frequency, 4V VIN 30V, 0.8V VOUT 5.25V LTC3855 Dual Output, 2-phase, Synchronous Step-Down DC/DC Controller with Diff Amp and DCR Temperature Compensation PLL Fixed Frequency 250kHz to 770kHz, 4.5V VIN 38V, 0.8V VOUT 12V LTC3853 Triple Output, Multiphase Synchronous Step-Down DC/DC Controller, RSENSE or DCR Current Sensing and Tracking PLL Fixed 250kHz to 750kHz Frequency, 4V VIN 24V, VOUT3 Up to 13.5V LTC3860 Dual, Multiphase, Synchronous Step-Down DC/DC Controller with Diff Amp and Three-State Output Drive Operates with Power Blocks, DRMOS Devices or External MOSFETs 3V VIN 24V, tON(MIN) = 20ns LTC3857/LTC3857-1 Low IQ, Dual Output 2-Phase Synchronous Step-Down DC/DC Controller with 99% Duty Cycle Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz, 4V VIN 38V, 0.8V VOUT 24V, IQ = 50A 3729fb 30 Linear Technology Corporation 0311 REV B * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2001