DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUITS uPC7800A SERIES THREE TERMINAL POSITIVE VOLTAGE REGULATORS DESCRIPTION pPC7800A series are monolithic three terminal positive regulators which employ internally current limiting, thermal shut down, output transistor safe operating area protection make them essentially indestructible. They are improved for ripple rejection ratio, line regulation, load regulation and quiescent current, as comparison of conventional uPC7800 series. FEATURES + Wide operation temperature range. * High ripple rejection ratio. * Good regulation (line, load). * Low quiescent current. Built-in protection circuits. (over current protection, SOA protection and thermal shut down) ORDER INFORMATION TYPE NUMBER | OUTPUT VOLTAGE PACKAGE QUALITY GRADE uPC7805AHF BV uPC7808AHF 8V uPC7893AHF 9.3V uPC7812AHF 12V MP-45G(ISOLATED TO-220) Standard uPC7815AHF 15 V uPC7818AHF 18. V uPC7824AHF 24V Please refer to Quality grade on NEC Semiconductor Devices (Document number IEI-1209) published by NEC Corporation to know the specification of quality grade on the devices and its recommended applications. EQUIVALENT CIRCUIT CONNECTION DIAGRAM . -O IN | Re Re Ois Os Qs 4 Qu 4 Ris Ris } Wy Marking Oro W = Ri2 =Ru NO [0 fr 3 tg OUT (0: Os fl Re & =Ris Ri +fan IN GNDOUT Q Qs 1 Rio Ff GND Document No. IC-3171 (O.D. No. IC-7983) Date Published December 1992 M . Printed in Japan NEC Corporation 1992NEC ABSOLUTE MAXIMUM RATINGS (Ta = 25 C) uPC7800A SERIES CHARACTERISTIC SYMBOL RATING UNIT Input Voltage VIN 35/40 (Note1) V Internal Power Dissipation Pr 15 (Note2) W Operating Ambient Temperature Range | Tost ~ 30 to + 85 c Operating Junction Temperature Range | Topxi) 30 to + 150 C Storage Temperature Range Tstg - 55 to + 150 C Thermal Resistance (junction to case) Rth{j-c) 5 C/W Thermal Resistance (junction to ambient)! Rihij-a) 65 C/W (Note1) uPC7805A, 08A, 93A, 12A, 15A, 18A : 35 V, uPC7824A : 40 V (Note2) Internally limited TYPICAL CONNECTION INPUT Di it uPC7800A Ci: Required if regulator is located an appreciable distance from power supply filter. C2: More than 0.1 pF D1: Needed for Vin < Vo D2: Needed for Vo < GND RECOMMENDED OPERATING CONDITIONS OUTPUT rO + I * : CHARACTERISTIC SYMBOL MIN. | TYP. }| MAX. | UNIT uPC7805AHF 7 10 25 pPC7808AHF 10.5 14 25 uPC7893AHF 12 15 24.5 Input Voltage VIN uPC7812AHF 14.5 19 30 Vv BPC7815AHF 17.5 23 30 pPC7818AHF 21 27 33 pPC7824AHF 27 33 38 Output Current lo All 0.005 0.5 1 A Operating Junction Tooth All _ 30 +125 C Temperature RangeNEC uPC7800A SERIES ELECTRICAL CHARACTERISTICS p.PC7805A (Vin = 10 V,lo = 500 mA, 0C = Tj = + 125 C) CHARACTERISTIC SYMBOL TEST CONDITIONS MIN.| TYP. | MAX. | UNIT , Tj = 25C 4.8 5.0 5.2 Output Voltage Vo 7V 2 Vin320V,5 mAS loS1A,Pt= 15 W| 4.75 5.25 Vv ~30C =Tj5 + 125C 4.75 5.25 Line Regulation rEGm LUE 25C. TVS VIN 25 V 7 | 30 | ow Ti= 25C, 8VEViNSE12V 2 15 Load Regulation REG: Tis 26 C, 5 MAS lo5 1.5 A 4 30 mV Ti = 25 C, 250 mA Slo = 750 mA 2 10 Quiescent Current IBIAS Tj= 25C 2.8 4.3 mA Quiescent Current 7V2ViNe25V 1.0 Alpias mA Change 5MASIoS1.0A 0.5 Output Noize Voltage Va Tj= 25 C, 10 Hz Sf = 100 kHz 40 200 |uVrms. Ripple Rejection RR Tj= 25 C, f = 120 Hz, 8V=EVinS 18 V 70 76 dB Dropout Voltage VbIF Tj= 25C, lo=1.0A 1.8 V Short Circuit Current loshort Ti = 25 C, Vin= 25 V 1.6 A Peak Output Current lOpeak Tj= 25 C, Vin= 10 V 1.7 2.2 2.8 A Temperature Coefficient | ayant | lo =5 mA, 0C ST) 5+ 125 C 0.4 mVPC of Output Voltage ELECTRICAL CHARACTERISTICS uPC7808A (Vin = 14 V,lo = 500 mA, 0C S Tj = + 125 C) CHARACTERISTIC SYMBOL TEST CONDITIONS MIN. | TYP. | MAX.| UNIT Tj = 25C 7.7 8.0 8.3 Output Voltage Vo 10.5VSVwS23V,5mASlS1A,Pr215W) 7.6 8.4 Vv - 30C = Tj) =+ 125C 7.6 8.4 ; . Tj= 25 C, 10.5 VSVin=25V 8 35 Line Regulation REGIn T= 25C, 11V2ViInE17V 3 25 mV Ti= 25C, 5mMASZ1051.5A 12 90 Load Regulation REG. [F225 C, 250 mA Slo = 750 mA a | 20 | Quiescent Current IBIAS Tj= 25 C 3 4.4 mA Quiescent Current 10.5 V=Vin=25V 1.0 Change Alews SE mASIOS10A o5 | Output Noize Voltage Vn Tj= 25 C, 10 Hz =f = 100 kHz 50 250 | uVems. Ripple Rejection ReR Tj= 25 C, f = 120 Hz,11.5 VS Vin S 21.5 V 66 72 dB Dropout Voltage Votr Tj= 25C, lo=1.0A 1.8 Vv Short Circuit Current loshort Tj = 25 C, Vin= 25 V 1.6 A Peak Output Current lopeak Tj= 25C, Vin= 14 V 1.7 2.2 2.8 A of Output Voltage AVo/AT | lo=5 mA, 0C ST) 5+ 125C - 0.6 mv/CNEC uPC7800A SERIES ELECTRICAL CHARACTERISTICS ,:PC7812A (Vin = 19 V, lo = 500 mA, 0C = Tj = + 125 C) CHARACTERISTIC SYMBOL TEST CONDITIONS MIN. | TYP. | MAX. | UNIT Tj) = 25C 11.5 | 12.0 | 12.5 Output Voltage Vo 145 VS Vn 5 27V,5 mMASlS1A,PrS15W | 11.4 12.6 Vv - 30 C ZTj 2+ 125C 11.4 12.6 . . Tj= 25 C, 14.5 V2 Vin S30 V 40 45 Line Regulation REGINn T,= 28 C, 16V=Vn=22V A 30 mV . Ti= 25C, 5mMAZ1021.5A 17 130 Load Regulation REG: T= 25 C, 250 MA = lo 750 mA 6 30 mV Quiescent Current lpias Tj= 25C 3.1 4.6 | mA Quiescent Current 14.5 VEVin=30V 1.0 mA Change dleias 5 mA SIZ 10A 05 Output Noize Voitage Vn Tj= 25 C, 10 Hz = f = 100 kHz 70 300 |HVrms. Ripple Rejection ReR Tj= 25 C, f = 120 Hz,15 V= Vin = 25 V 62 68 dB Dropout Voltage Vorr Tj= 25C, lo=1.0A 1.8 Vv Short Circuit Current loshort Tj= 25 C, Vin= 30 V 1.3 A Peak Output Current lopeak Tj)= 25C, Vin= 19 V 1.7 2.2 2.8 A Temperature Coefficient AVo/AT | loa mA, 0C ET) 54 125C _08 mvc of Output Voltage ELECTRICAL CHARACTERISTICS uPC7815A (Vin = 23 V, lo = 500 mA, 0 C = Tj = + 125 C) CHARACTERISTIC SYMBOL TEST CONDITIONS MIN. | TYP. | MAX. | UNIT Tj = 25C 14.4 15.0 15.6 Output Voltage Vo 17.5 VS Vw S 30 V,5 mMAS loS 1A, Pr=15W | 14.25 15.75 Vv - 30C = Tj 2+ 125C 14.25 15.75 Tj= 25 C, 17.5 V = Vin 5 30 V 10 45 Line Regulation REGINn Ti= 25 C, 20 VS Vin526V 5 35 mV Tj= 25C, 5 mA =102=1.5A 25 190 Load Regulation REG. [75= 25 C, 250 mA Slo = 750 mA 8 | 40) Quiescent Current IBias T)= 25C 3.3 4.8 mA Quiescent Current 17.5 V3 Vin = 30 V 1.0 Change Alsias 5MAZ=1l021.0A 0.5 mA Output Noize Voltage Vn Tj= 25 C, 10 Hz =f = 100 kHz 85 400 |uVrms. Ripple Rejection RR T= 25 , f = 120 Hz,18.5 V= Vin = 28.5 V 60 66 dB Dropout Voltage Vole Tj= 25C, lo=1.0A 1.8 Vv Short Circuit Current loshort Tj = 25 C, Vin= 30 V 1.3 A Peak Output Current lopeak Tj = 25 C, Vin= 23 V 17 2.2 2.8 A Temperature Coefficient | VolaT | lo= 5 mA, 0C ST) S+ 125C 11 mV/C of Output VoltageNEC ELECTRICAL CHARACTERISTICS uPC7818A (Vin = 27 V, lo = 500 mA, 0C & Tj = + 125 C) uPC7800A SERIES CHARACTERISTIC SYMBOL TEST CONDITIONS MIN. | TYP. | MAX. } UNIT Tj = 25 C 17.3 | 18.0 | 18.7 Output Voltage Vo 21V = Vn = 33 V,5 mMA= loS1A,PrS 15 W 17.1 18.9 Vv - 30C STj 3+ 125C 17.1 18.9 . . Tj= 25C, 21VEVn=E33 V 12 60 mV Line Regulation REGin T,= 26 C, 24V = Vin=30V 6 45 Tj= 25C, 5mMAS1l0=1.5A 32, | 110 | mV Load Regulation REG. [7;= 25 C, 250 mA Slo = 750 mA 10 | 40 Quiescent Current ibias Tj= 25 C 3.4 5.0 mA Quiescent Current Aleias 21VEVinS33 V 1.0 mA Change 5 mA S1l21.0A 0.5 Output Noize Voltage Vn Tj = 25 C, 10 Hz = f = 100 kHz 95 450 [pVems. Ripple Rejection ReR Tj= 25 C, f = 120 Hz, 22 VS Vin S 32V 59 65 dB Dropout Voltage Voir Ti= 25C, lo=1.0A 1.8 Vv Short Circuit Current loshort Tj = 25 C, Vin= 33 V 1.2 A Peak Output Current lopeak Tj= 25 C, Vin= 27 V 1.7 | 2.2 2.8 A Temperature Coefficient AVo/AT | loz 5 mA, 0C ET) 5+ 125C - 1.3 mv/C of Output Voltage ELECTRICAL CHARACTERISTICS pPC7824A (Vin = 33 V, lo = 500 mA, 0C = Tj = + 125 C) CHARACTERISTIC SYMBOL TEST CONDITIONS MIN. | TYP. | MAX. | UNIT Tj) = 25C 23.0 | 24.0 | 25.0 Output Voltage Vo 27 V = Vin = 38 V,5 MAS lo 1A, Pr= 15 W 22.8 25.2 Vv - 30C ST) 3+ 125C 22.8 25.2 . . Ti= 25C, 27 VEVin = 38 V 15 80 Line Regulation REGIN T= 25 C, 30 VE Vin = 36 V 8 50 mv Ti= 25C, 5 mMAZlo=1.5A 44 150 Load Regulation REGL [7/226 C, 250 mA Slo 5 750 mA 14 | 50 | Quiescent Current IBiAs Tj= 25 C 3.6 5.3 mA Quiescent Current Aleias 27V2EViNE38 V 1.0 mA Change 5BMmMAS1IS1.0A 0.5 Output Noize Voltage Vn Tj = 25 C, 10 Hz = f = 100 kHz 120 500 jpuVems. Ripple Rejection ReR Tj = 25 C, f = 120 Hz, 28 VS Vin = 38 V 55 62 dB Dropout Voltage Vote Tj= 25C, lo=1.0A 2.0 Vv Short Circuit Current loshort Tj= 25 C, Vin= 38 V 1.0 A Peak Output Current lopeak Tj= 25 C, Vin= 33 V 1.7 2.2 2.8 A Temperature Coefficient | oat | lox 5 mA, 0C STi $+ 125C 17 mV/C of Output VoltageNEC uPC7800A SERIES ELECTRICAL CHARACTERISTICS p:PC7893A (Vin = 15 V, lo = 500 mA, 0C = Tj = + 125 C) CHARACTERISTIC SYMBOL TEST CONDITIONS MIN. | TYP. | MAX. | UNIT Tj = 25C 9.0 9.3 9.5 Output Voltage Vo 12 VS Vin S 24.5 V,5 mAS loS 1A, PrS 15 W 8.9 9.7 Vv - 30C ST) =+ 125C 8.9 9.7 Line Regulation REGin Ti= 25 C, 12 VS Vin = 26.5 V 9 40 mv Ti= 25C, 12.5 VS Vin= 18.5 V 4 30 ; Tj= 25C, 5 mAS1l051.5A 15 110 Load Regulation REG T,= 25 C, 250 MA =l0=750 mA 5 25 mV Quiescent Current IBIAS Tj= 25C 3.1 4.5 mA Quiescent Current 12V =Vin= 26.5 V 1.0 AlBias mA Change 5MASI=S1.0A 0.5 Output Noize Voltage Vn Tj= 25 C, 10 Hz = f = 100 kHz 55 230 [uVi.ms. Ripple Rejection ReR Tj= 25 C, f = 120 Hz,12.5 V = Vin 5 22.5 V 64 70 dB Dropout Voltage Vole Tj= 25C, lo=1.0A 1.8 V Short Circuit Current lOshort Tj = 25 C, Vin = 26.5 V 1.5 A Peak Output Current lopeak Tj = 25 C, Vin= 15 V 1.7 2.2 2.8 A Temperature Coefficient | avant | jo=5 mA, 0C ST) 5+ 125C ~0.7 mv/C of Output VoltageNEC uPC7800A SERIES TYPICAL CHARACTERISTICS (Ta = 25 C) Po- Ta NNo- Tj 25 > E 50 s 20 5 o| _#PC7B08A S ty. 8 rab N 3 he & -50L cle L PSS a 15 Se a 8 % 2 100 L 5 C g 7 /, \ ro S 10 S _150 UPC7824A\ & a ] 3 -200 1.92 W q Without Heatsink | 85 C = ~250 ~300 0 25 50 75 100 125 150 ~50 0 50 100 150 Ta - Ambient Temperature C Tj- Junction Temperature C Voir - Tj lOpeak (VinN-Vo) 2.5 3.0 lo=1A < > 20 Si 38 fl Po 5 > 5 20 a =, 3 18 g / SK, 3 9 2 2 1s a SES = , Oo 5 10 = Uy PP RES 250 a 1.0 P 7 l 0. oS <5 7c a x Pp > 05 $ 05 g . 0 50 0 50 100 150 0 5 10 15 20 25 30 35 Ti- Junction Temperature C (Vin-Vo) - Input to Output Voltage Differential - V Vo - VIN 8 Tj= 25C 100 5 uPC7805A 90 isa} > 6 3 80 1 g s 8 5 "4 B 60 6 9 VL. @ > 4 AIFS & 50 5 Ca ~500 mA 2 3 Mf a 40 Oo 2 to, = 30 > Vy. oc J cc 20 1 Y 10 Z 0 1 2 3 4 5 6 7 8 10 100 1k 10k 100 k Vin Input Voltage - V f - Frequency HzNEC uPC7800A SERIES LINE TRANSIENT RESPONSE LOAD TRANSIENT RESPONSE 7 Vi=10V 8, 5 10 uPC7805A B05 s To A zg I | zZ oO z 2 ont oa -1.0 4Vo Output Voltage Deviation - mV AVo - Output Voltage Deviation - mV & on 0 5 10 15 20 25 30 t- Time - us t- Time -ys 1000 100 Ro- Output Impedance mQ 10 100 1k 10k 100 k f - Frequency HzuPC7800A SERIES PACKAGE DIMENSIONS 3PIN PLASTIC SIP (MP-45G) a a 1 3 HE a J vl ot nF P3HF-254B-1 ITEM MILLIMETERS INCHES Tech ead centerline is located within 0.25 mm A as oan MAX (0.01 inch) of its true position (T.P.) at maxi- B 7.0 0.276 mum material condition. c 1.2 MIN. 0.047 MIN. 7 D 17.07 0.66928813 E $3.37" 0.130" F 0.757" 0.03078.888 G 0.25 0.010 H 2.54 (T.P.) 0.100 (T.P.) 5.0*5 0.1977 J 2.66 MAX. 0.105 MAX. ~ K 4.8 MIN. 0.188 MIN. L 8.5 0.335 M 8.5 0.335 N 4.579? 0. 1 77 70.008 P 2.8%? 0.110 8888 Qa 22.4 MAX, 0.882 MAX. U 2.4*8 0.094 78:34 Vv 0.6577 " 0.02678:808 Y g.977 0.350700 Z 1.0 MIN. 0.039 MIN.NEC | uPC7800A SERIES RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. Please consult with our sales offices in case other soldering process is used, or in case soldering is done under different conditions. TYPES OF THROUGH HOLE MOUNT DEVICE uPC7800AHF Series Soldering process Soldering conditions Symbol . Solder temperature : 260 C or below. Wave soldering Flow time : 10 seconds or below. 10NEC uPC7800A SERIES [MEMO] 11NEC uPC7800A SERIES [MEMO] No part of this document may be copied or reproduced in any from or by any means without the prior written consent of NEC Corporation.NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. The devices listed in this document are not suitable for use in aerospace equipment, submarine cables, nuclear reactor control systems and life support systems. If customers intend to use NEC devices for above applications or they intend to use "Standard" quality grade NEC devices for applications not intended by NEC, please contact our sales people in advance. Application examples recommended by NEC Corporation. Standard: Computer, Office equipment, Communication equipment, Test and Measurement equipment, Machine tools, Industrial robots, Audio and Visual equipment, Other consumer products, etc. Special: Automotive and Transportation equipment, Traffic control systems, Antidisaster systems, Anticrime systems, etc. M4 92.6