3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 Anwendermodul 4 A Betriebsanleitung Bestell-Nr.: 3ZX1012-0RG00-0BN1 Anwendungsbereich Das Anwendermodul 4 A besitzt 4 potentialfreie Ausgange, mit denen Sie Aktuatoren ansteuern konnen. Fur die Ausgangskreise benotigen Sie eine externe Zusatzeinspeisung. Montage/ Verdrahtung Koppelmodul FK Deutsch Koppelmodul FK-E U AS-I UAS-I 0,8 Nm 4x Ue Verschlukappe Ue 2 1 1 3 Zusatzeinspeisung Ue 1: + Ue 3: 0 V 3RG9001-0AB00 3RG9001-0AL00 Inbetriebnahme 4 Ue = 24 V... 48 V DC Ue = 24 V DC Ausgange: 1: nicht belegt 3 2: nicht belegt 3: 0 V 4: Schaltausgang 3RG9001-0CB00 Ue = 24 V DC Fuhren Sie folgende Schritte aus, um das Anwendermodul in Betrieb zu nehmen: Schritt Vorgehensweise 1 Stellen Sie die Adresse ein. Verwenden Sie dazu - das Adressiergerat oder - das Programmier- und Service-Gerat (PSG) Gultige Adressen sind 1 bis 31. Verwenden Sie jede Adresse nur einmal. 2 3RG9001-0A.00: Legen Sie die gelbe(n) AS-I-Leitung(en) in die Leitungsfuhrung(en) des Koppelmoduls FK. 3RG9001-0CB00: Legen Sie die gelbe AS-I-Leitung und die schwarze AS-I- Energieleitung in die Leitungsfuhrungen des Koppelmoduls FK-E. Beachten Sie die Farbcodierung ! 3 Schrauben Sie das Anwendermodul auf dem Koppelmodul fest. Die grune LED leuchtet bei vorhandener AS-I-Spannung. 4 3RG9001-0A.00: Schlieen Sie die Zusatzeinspeisung an dem M12-Stecker (Auengewinde) an. 5 Schlieen Sie bis zu 4 Aktuatoren an den M12-Buchsen (Innengewinde) an. Schaltungsbeispiel fur den Anschlu von Aktuatoren: 1 3 GWA 4NEB 333 0203-10 16 A + - Ue 1 Logische Zuordnung Hinweise Folgende Tabelle zeigt die logische Zuordnung der Datenbits: Datenbit Bedeutung LEDs (gelb) Vorderansicht D0 Ausgang O - 1 1 Buchse 1 D1 Ausgang O - 2 2 Buchse 2 D2 Ausgang O - 3 3 Buchse 3 D3 Ausgang O - 4 4 Buchse 4 * Decken Sie nicht benutzte M12-Buchsen mit Verschlukappen (Best.-Nr.: 3RX9802-0AA00) ab, um die Schutzart IP 67 zu erreichen. * Beschalten Sie induktive Verbraucher mit Freilaufdioden. * Die Zusatzeinspeisung mussen Sie mit maximal 16 A zentral absichern. * 3RG9001-0AB00: Bei einem Ausfall der Kommunikation bleiben die Relais-Ausgange im aktuellen Schaltzustand. Wenn die Relais-Ausgange ruckgesetzt werden sollen, dann verwenden Sie ein Uberwachungsmodul (Best.-Nr.: 3RG9008-0AF00). * 3RG9001-0AL00 /-0CB00: Bei einem Ausfall der Kommunikation werden die Ausgange automatisch ruckgesetzt. Technische Daten 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 8/0 60 mA eingebaut 8/0 20 mA eingebaut 8/0 20 mA eingebaut 24 V...48 V DC 24 V DC nicht eingebaut eingebaut (extern mit 2A Trag abzusichern 24 V DC eingebaut Elektrische Daten gema AS-I-Spezifikation IO-Code / ID-Code Leerlaufstrom Verpolschutz I0 Ausgange Externe Zusatzeinspeisung Kurzschluschutz Ue Strombelastbarkeit (max. 2 A pro Modul) I Schaltspiele 1A 0,5 A (24 V DC) 0,2 A (48 V DC) typ. 2 x 106 DC 12 DC 13 DC 13 DC 12 0,7 A 0,5 A - *) 0,7 A 0,5 A - *) *) Halbleiterausgang EMV-Festigkeit 8 kV 10 V/m 1 kV / 2 kV IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 Mechanische Daten Schutzart Gewicht Abmessungen (H x B x T) [mm] Schockbeanspruchung Schraubmontage Schnappmontage Schwingbeanspruchung Schraubmontage Schnappmontage IP 67 (mit Koppelmodul) Ca. 150 g 90 x 45 x 27 30 g / 18 ms 15 g / 11 ms 10...55 Hz, 1 mm Amplitude (mit Koppelmodul) 10...55 Hz, 0,5 mm Amplitude (mit Koppelmodul) Temperaturbereich Bemessungstemperatur Umgebungstemperatur Lagertemperatur 2 Tu Ta Ts 25 C - 25 C ...85 C - 40 C ...85 C User module 4 A 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 Instructions Application Installation/ wiring Order No.: 3ZX1012-0RG00-0BN1 English The user module 4 A has 4 electrically isolated outputs which you can use for operating such items as actuators. For the output circuits, you will require a supplementary external supply. . Coupling module FK Coupling module FK-E U AS-I UAS-I 0.8 Nm 4x Ue Closing plug Ue 2 1 3 Supplementary voltage Ue 1: + U e 3: 0 V 3RG9001-0AB00 3RG9001-0AL00 Putting into service 1 4 Ue = 24 V to 48 V DC Ue = 24 V DC Outputs: 1: not in use 3 2: not in use 3: 0 V 4: Switching output 3RG9001-0CB00 Ue = 24 V DC For putting the user module into service, the steps are as follows: Step Procedure 1 Set the address. To do this, use - the addressing unit or - the programming and service unit (PSG) Valid addresses are 1 to 31. Use each address once only. 2 3RG9001-0A.00: Fit the yellow AS-I conductor rail(s) in the guide(s) on the coupling module FK. 3RG9001-0CB00: Fit the yellow AS-I conductor rail and the black AS-I power rail in in the guides on the coupling module FK-E. Pay attention to the colour coding! 3 Screw the user module tightly onto the coupling module. The green LED lights up when AS-I voltage is present. 4 3RG9001-0A.00: Connect the supplementary supply to the M12-plug (outside thread). 5 Connect up a maximum of 4 actuators to the M12 sockets (inside thread). Example of actuator connection: 1 3 16 A + - Ue 3 Logical Assignment Notes The table below shows the logical assignment of the data bits: Data bit Meaning LEDs (yellow) Front view D0 Output O - 1 1 Socket 1 D1 Output O - 2 2 Socket 2 D2 Output O - 3 3 Socket 3 D3 Output O - 4 4 Socket 4 * To attain degree of protection IP 67, insert closing plugs (Order No.: 3RX9802-0AA00) in the M12 sockets not in use. * Connect inductive loads via free-wheeling diodes. * The supplementary power supply must be centrally fused with 16 A. * 3RG9001-0AB00: If communications are interrupted, the relay outputs retain their switching status. If it is necessary for the relay outputs to be reset, use the watch dog module (Order No.: 3RG9008-0AF00). * 3RG9001-0AL00 /-0CB00: If communications are interrupted, the outputs are reset automatically. Technical Data 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 8/0 60 mA Integrated 8/0 20 mA Integrated 8/0 20 mA Integrated 24 V to 48 V DC 24 V DC Not integrated Integrated (must be fused externally with 2 A slow-blow) 24 V DC Integrated Electrical data as per AS-I Specification IO-Code / ID-Code No-load current Polarity reversal protection I0 Outputs Supplementary ext. power supply Short-circuit protection Ue Current carrying capacity (max. 2 A per module) DC 12 DC 13 DC 13 Switching cycles DC 12 I 1A 0.5 A (24 V DC) 0.2 A (48 V DC) typ. 2 x 106 0.7 A 0.5 A - *) *) Semiconductor output EMC stability 8 kV 10 V/m 1 kV / 2 kV IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 Mechanical data Degree of protection Weight Dimensions (H x W x D) [mm] Shock stress Screw mounting Snap-on mounting Vibration stress Screw mounting IP 67 (with coupling module) Ca. 150 g 90 x 45 x 27 30 g / 18 ms 15 g / 11 ms 10 to 55 Hz, 1 mm amplitude (with coupling module)) 10 to 55 Hz, 0.5 mm amplitude (with coupling module) Snap-on mounting Temperature range Rated temperature Ambient temperature Storage temperature 4 Tu Ta Ts 25 C - 25 C to 85 C - 40 C to 85 C 0.7 A 0.5 A - *) Module utilisateur 4 A 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 Instructions de service Domaine d'emploi N de reference : 3ZX1012-0RG00-0BN1 Francais Le module 4 S comporte 4 sorties libres de potentiel permettent de commander des actionneurs. Les circuits de sortie doivent etre alimentes a partir d'une source externe. Montage/ cablage Embase FK Embase FK-E U AS-I UAS-I 0,8 Nm 4x Ue Bouchon Ue 2 1 1 3 Alim. externe Ue Mise en service 1 : + Ue 3:0V 3RG9001-0AB00 3RG9001-0AL00 4 Ue = 24 V... 48 V cc Ue = 24 V cc Sorties : 1 : inutilisee 3 2 : inutilisee 3:0V 4 : sortie 3RG9001-0CB00 Ue = 24 V cc Effectuez les operations suivantes pour mettre le module en service : Etape Operation 1 Reglez l'adresse. Utilisez a cet effet - le terminal d'adressage ou - la console de programmation et maintenance (PSG). Adresses valables : 1 a 31. Chaque adresse ne doit intervenir qu'une seule fois. 2 3RG9001-0A.00 : posez le ou les cables AS-I jaunes dans le ou les guides de l'embase FK. 3RG9001-0CB00 : posez le cable AS-I jaune et le cable d'energie AS-I noir dans les guides de l'embase FK-E. Respecter le codage de couleur. 3 Vissez le module utilisateur sur l'embase. La LED verte s'allume lorsque la tension AS-I est presente. 4 3RG9001-0A.00 : raccordez l'alimentation externe au connecteur M12 (filetage exterieur). 5 Raccordez les actionneurs (au maximum 4) aux connecteurs M12 (filetage interieur). Exemple de raccordement d'actionneurs : 1 3 16 A + - Ue 5 Affectation logique Remarques Caracteristiques techniques Le tableau suivant donne l'affectation logique des bits de donnees : Bit Signification LED (jaune) Vue de face D0 Sortie O - 1 1 Connect. 1 D1 Sortie O - 2 2 Connect. 2 D2 Sortie O - 3 3 Connect. 3 D3 Sortie O - 4 4 Connect. 4 Priere de tenir compte des remarques suivantes : * Obturez les connecteurs M12 inutilises avec des bouchons (n de ref. 3RX9802-0AA00) pour obtenir le degre de protection IP 67. * Antiparasitez les consommateurs inductifs avec des diodes de roue libre. * L'alimentation externe doit etre protegee de facon centrale (calibre max. 16 A). * 3RG9001-0AB00 : en cas de defaillance de la communication, les sorties a relais conservent leur etat. Si elles doivent etre remises a 0, utilisez le module de surveillance (n de ref. 3RG9008-0AF00). * 3RG9001-0AL00 /-0CB00 : en cas de defaillance de la communication, les sorties a relais sont automatiquement remises a 0. 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 8/0 60 mA integree 8/0 20 mA integree 8/0 20 mA integree 24 V...48 V cc 24 V cc integree non integree (prevoir fusible externe 2 A lent) 24 V cc integree Caract. electriques selon specification AS-I Code IO / Code ID Consommation totale Prot. contre inversion de pol. I0 Sorties Alimentation externe Prot. contre courts-circuits Ue Courant admissible (2 A max. par module) I 1A 0,5 A (24 V cc) 0,2 A (48 V cc) typ. 2 x 106 DC 12 DC 13 DC 13 Cycles de manoeuvres DC 12 0,7 A 0,5 A - *) 0,7 A 0,5 A - *) *) sortie a semiconducteur Compatibilite electromagnetique CEI 61000-4-2 CEI 61000-4-3 CEI 61000-4-4 8 kV 10 V/m 1 kV / 2 kV Caracteristiques mecaniques Degre de protection Poids Dimensions (H x L x P) [mm] Tenue aux chocs Fixation vissee Fixation encliquetee Tenue aux vibrations Fixation vissee Fixation encliquetee IP 67 (avec embase) env. 150 g 90 x 45 x 27 30 g / 18 ms 15 g / 11 ms 10 a 55 Hz, amplitude 1 mm (avec embase) 10 a 55 Hz, amplitude 0,5 mm (avec embase) Plage de temperature Temperature assignee Temperature ambiante Temperature de stockage 6 Tu Ta Ts 25 C - 25 C a 85 C - 40 C a 85 C Modulo utilizzatore 4 A 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 Istruzioni di servizio Campo d'impiego N. di ordinazione: 3ZX1012-0RG00-0BN1 Italiano Il modulo utilizzatore 4 A dispone di 4 uscite a potenziale zero tramite le quali si possono comandare attuatori. Per i circuiti di uscita occorre un'alimentazione supplementare esterna. Montaggio/ cablaggio Modulo di accoppiamento FK Modulo di accoppiamento FK-E U AS-I UAS-I 0,8 Nm 4x Ue Ue Capsula di chiusura 2 1 1 3 Alim. supplementare U e1: + Ue 3: 0 V 3RG9001-0AB00 3RG9001-0AL00 Messa in servizio 4 Ue = 24 V... 48 V DC Ue = 24 V DC 3RG9001-0CB00 Ue = 24 V DC Uscite: 1: non occupato 3 2: non occupato 3: 0 V 4: Uscita di commutazione Procedere come segue per mettere in servizio il modulo utilizzatore: Passo Procedura 1 Impostare l'indirizzo. Impiegare a tal fine - il programmatore indirizzi oppure - il dispositivo di programmazione e di service (PSG) Gli indirizzi validi sono gli indirizzi da 1 a 31. Utilizzare ciascun indirizzo una sola volta. 2 3RG9001-0A.00: inserire il cavo giallo (o i cavi gialli) AS-i nella guida (o nelle guide) del modulo di accoppiamento FK. 3RG9001-0CB00: inserire il cavo giallo AS-i e il cavo di alimentazione nero AS-i nelle guide del modulo di accoppiamento, rispettando i codici colorati. 3 Avvitare saldamente il modulo utilizzatore al modulo di accoppiamento. Il LED verde si illumina in presenza di tensione AS-i. 4 3RG9001-0A.00: collegare l'alimentazione supplementare al connettore M12 (filettatura esterna). 5 Collegare fino a 4 attuatori ai connettori M12 (filettatura interna). Schema di esempio per collegare gli attuatori: 1 3 16 A + - Ue 7 Assegnazione logica Avvertenze La tabella seguente riporta l'assegnazione logica dei bit di dati: Bit di dati Significato LED (gialli) Vista frontale D0 Uscite O - 1 1 Connettore 1 D1 Uscite O - 2 2 Connettore 2 D2 Uscite O - 3 3 Connettore 3 D3 Uscite O - 4 4 Connettore 4 * Chiudere i connettori M12 non utilizzati con le apposite capsule (n. di ordinazione: 3RX9802-0AA00) per ottenere il grado di protezione IP 67. * Collegare dei diodi antidisturbi alle utenze induttive. * L'alimentazione supplementare deve essere protetta centralmente con max. 16 A. * 3RG9001-0AB00: in caso di interruzione della comunicazione, le uscite a rele restano nello stato di commutazione in cui si trovavano. Se occorre resettare le uscite a rele, si deve utilizzare un modulo di sorveglianza (n. di ordinazione: 3RG9008-0AF00). * 3RG9001-0AL00 /-0CB00: in caso di interruzione della comunicazione, le uscite vengono resettate automaticamente. Dati tecnici 3RG9001-0AB00 3RG9001-0AL00 3RG9001-0CB00 8/0 60 mA integrata 8/0 20 mA integrata 8/0 20 mA integrata 24 V...48 V DC 24 V DC 24 V DC non integrata integrata integrata 0,7 A 0,5 A - *) 0,7 A 0,5 A - *) Dati elettrici secondo la specifica AS-i Codice IO / codice ID Corrente a vuoto I0 Protezione dall'inversione di polarita Uscite Alimentazione supplementare esterna Protezione da cortocircuiti Ue (serve protezione esterna con ritardo a 2A) Carico di corrente ammissibile (max. 2 A per modulo) DC 12 DC 13 DC 13 Cicli di commutazione DC 12 I 1A 0,5 A (24 V DC) 0,2 A (48 V DC) tip. 2 x 106 *) Uscita a semiconduttore Immunita EMC 8 kV 10 V/m 1 kV / 2 kV IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 Dati meccanici Grado di protezione Peso Dimensioni (A x L x P) [mm] Sollecitazione da urto Montaggio a vite Montaggio a innesto Sollecitazione da vibrazioni Montaggio a vite Montaggio a innesto IP 67 (con modulo di accoppiamento) ca. 150 g 90 x 45 x 27 30 g / 18 ms 15 g / 11 ms 10...55 Hz, 1 mm di ampiezza (con modulo acc.) 10...55 Hz, 0,5 mm di ampiezza (con modulo acc.) Campo di temperatura Temperatura nominale Temperatura ambiente Temperatura di magazzinaggio Technische Anderungen vorbehalten. Subject to change without prior notice. (c) Siemens AG 1996 Tu Ta Ts 25 C - 25 C ...85 C - 40 C ...85 C Bestell-Nr./Order No.: 3ZX1012-0RG00-0BN1 Printed in the Federal Republic of Germany