2K x 8 Reprogrammable PROM
CY7C291A
CY7C292A/CY7C293A
Cypress Semiconductor Corporation 3901 North First Street San Jose CA 9 5 1 3 4 408- 943-2600
March 1986 – Revised May 1993
1CY7C29 2A
Features
Windowed for reprogrammability
CMOS for optimum speed/power
High speed
20 ns (commercial)
2 5 n s (m ilit ary )
Low power
660 mW (commercial and military)
Low standby power
220 mW (commercial and military)
EPROM technology 100% progr ammable
Slim 300-mil or stan dard 600-mil packaging available
5V ±10% VCC, commercial and military
TTL-compatible I/O
Direct replacement for bipolar PROMs
Capable of withstanding >2001V st atic discharg e
Function al Des cription
The CY7C291A, CY7C292A, and CY7C29 3A are high -perfor-
manc e 2K-word by 8-bit CMOS PROMs. They are functionally
identical, but are packag ed in 300-mil (7C29 1A, 7C293 A) and
600-mil wide plastic and hermetic DIP packages (7C292A).
The CY7C293A has an automatic power down featur e which
reduces the power consumpti o n by ov er 70% when deselect-
ed. The 300-mil ceramic package may be equipped with an
erasure window; when exposed to UV light the PROM is
erased and can then be reprogrammed. The memory cells uti-
lize proven EPROM floating-gate technology and byte-wide in-
telligent programmi ng algorithm s.
The CY7C291A, CY7C292A, and CY7C293A are plug-in re-
placements for bipolar devices and offer the advantages of
lower power, reprogrammability, superior performance and
programming yield. The EPROM cell requires only 12.5V for
the supervoltage and low current requirements allow for gang
program ming. The EPROM cells allow for each memory loca-
tion to be tested 100%, as each loc ation is written into, erased ,
and repeatedly exercised prior to encapsulation. Each PROM
is also tested for AC performance to gu aran tee that after cus-
tomer programming the product will meet DC and AC specifi-
cation limi ts.
A read is accomplished by placing an active LOW signal on
CS1, and active HIGH signals on CS2 and C S3. The contents
of the memory location addressed by the address line (A0
A10) will b ecome available on the output lines ( O0 O7).
LogicBlockDiagram Pin Configurations
C291A-1
C291A-2 C291A-3
O7
O6
O5
O4
O3
O2
O1
O0
PROGRAM-
MABLE
ARRAY
MULTI-
PLEXER
GND
1
2
3
4
5
6
7
8
9
10
11 14
15
16
20
19
18
17
21
24
23
22
A6
A5
A4
A3
A2
A1
A0
O0
A7
O3
VCC
A8
A9
A10
O7
O6
O5
O4
CS1
O212 13
O1
CS3
CS2
28
4
5
6
7
8
9
10
321 27
1314151617
26
25
24
23
22
21
20
1112 19O018
NC
A0
A4
A3
A10
NC
CS1
CS2
O7
O6
A2
A1CS3
CS1
CS2
CS3
POWER
DOWN
7C293A Window availableon
7C291A and 7C293A
only.
DIP LCC/PLCC (Opaque Only)
Top View Top View
ADDRESS
DECODER
A0
A1
A2
A3
A4
A5
A6
A8
A9
A10
A7
COLUMN
ADDRESS
ROW
ADDRESS
7C291A
7C292A
7C293A 7C291A
7C293A
CY7C291A
CY7C292A/CY7C293A
2
Maximum Ratings
(Above which the useful l ife may be impaired. For user guide-
lines, not tested.)
Storage Temperature ......................................65°C to+150°C
Ambient Temperature with
Power Applied...................................................55°C to+125°C
Supply Volt a ge to Ground Potential..................0.5V to+7.0V
DC Voltage Applied to Outputs
in High Z State......................................................0.5V to+7.0V
DC Input Voltage.................................................3.0V to +7.0V
DC Program Voltage... ................. ......................... ........13.0V
UV Exposure.................. ................. ....... .......7258 Wsec/cm2
Static Dischar g e Voltag e.. ........ ................... .......... .....>2001V
(per MIL-S TD-88 3, Method 3015)
Latch-Up Current........................ ...................... .......>200 mA
Selection Guid e
7C291A-20
7C292A-20
7C293A-20
7C291A-25
7C292A-25
7C293A-25
7C291AL-25
7C292AL-25
7C293AL-25
7C291A-35
7C292A-35
7C293A-35
7C291AL-35
7C292AL-35
7C293AL-35
7C291A-50
7C292A-50
7C293A-50
7C291AL-50
7C292AL-50
7C293AL-50
Maximum Access Ti me (ns) 20 25 35 50
Maximum Operati ng
Cur rent (mA) Standard Commercial 120 90 90 90
Military 120 90 90
LCommercial 60 60 60
Standby Current (mA)
7C293A Only Commercial 40 30 30 30
Military 40 40 40
Operating Range
Range Ambient
Temperature VCC
Commercial 0°C to + 70°C 5V ±10%
Industrial[1] 40°C to + 85°C 5V ±10%
Military[2] 55°C to + 125°C 5V ±10%
Notes:
1. Contact a Cy press representative for industrial temperature range spec-
ifications.
2. TA is the “instant on” c ase tempe rat ure.
CY7C291A
CY7C292A/CY7C293A
3
Electrical Characteristics Over the Operating Range[3,4]
7C291A-20
7C292A-20
7C293A-20
7C291A-25
7C292A-25
7C293A-25
7C291AL-25
7C292AL-25
7C293AL-25
Parameter Description Test Conditions Min. Max. Min. Max. Min. Max. Unit
VOH Output HIGH Voltage VCC = M in., IOH = 4.0 mA 2.4 2.4 2.4 V
VOL Output LOW Voltage VCC = M in., IOL = 16.0 mA 0.4 0.4 0.4 V
VIH Input HIGH Voltage Guar anteed Input Logical
HI G H Voltage for All Inputs 2.0 VCC 2.0 VCC 2.0 VCC V
VIL Input LOW Voltage G uarante ed Input Logical
LOW Voltage for All Inputs 0.8 0.8 0.8 V
IIX Input Load Current GND < VIN < VCC 10 +10 10 +10 10 +10 µA
VCD Input Diode Clamp Voltage Note 4
IOZ Output Leakage Current GND < VOUT < VCC,
Output Disabled 10 +10 10 +10 10 +10 µA
IOS Output Short Circui t
Current[5] VCC = M ax., VOUT = GND 20 90 20 90 20 90 mA
ICC VCC O perating Supply
Current VCC = M ax.,
IOUT = 0 mA Com’l 120 90 60 mA
Mil 120
ISB Standby Supply Current
(7C293A Only) VCC = Max.,
CS1 = VIH Com’l 40 30 30 mA
Mil 40
VPP Prog ramming Supply Voltage 12 13 12 13 12 13 V
IPP Prog ramming Supply Current 50 50 50 mA
VIHP Input HIGH Programming
Voltage 3.0 3.0 3.0 V
VILP Input LOW Programming
Voltage 0.4 0.4 0.4 V
Notes:
3. See the last page of this specification for Gr oup A subgroup testing information.
4. See the “I ntroduction to CMOS PROMs” section of the Cypress Data Book for general information on testing.
5. For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed 30 seconds.
CY7C291A
CY7C292A/CY7C293A
4
Electrical Characteristics Over the Operating Range[3,4] (continued)
7C291AL-35, 50
7C292AL-35, 50
7C293AL-35, 50
7C291A-35, 50
7C292A-35, 50
7C293A-35, 50
Parameter Description Test Conditions Min. Max. Min. Max. Unit
VOH Output HIGH Voltage VCC = M in., IOH = 4.0 mA 2.4 2.4 V
VOL Output LOW Voltage VCC = M in., IOL = 16.0 mA 0.4 0.4 V
VIH Input HIGH Voltage Guar anteed Input Logical
HI G H Voltage for All Inputs 2.0 2.0 V
VIL Input LOW Voltage Guar anteed Input Logical
LOW Voltage for All Inputs 0.8 0.8 V
IIX In put Load Current GND < VIN < VCC 10 +10 10 +10 µA
VCD Input Diode Clamp Voltage Note 4
IOZ Outp ut Leakage Current GND < VOUT < VCC,
Output Disabled 10 +10 10 +10 µA
IOS Output Short Cir cuit Current[5] VCC = Max ., VOUT = GND 20 90 20 90 mA
ICC VCC O perating Supply Current VCC = Max.,
VIN = 2.0V
IOUT=0 mA
Commercial 60 90 mA
Military 90
ISB Standby Supply Current
(7C293A Only) VCC = Max.,
CS1 =VIH Commercial 30 30 mA
Military 40
VPP Pro gramming Supply Volt age 12 13 12 13 V
IPP Pro gramming Supply Current 50 50 mA
VIHP Input HIGH Prog ramming V oltage 3.0 3.0 V
VILP Input LOW Prog ramming V ol tage 0.4 0.4 V
Capacitance[4]
Parameter Description Test Conditions Max. Unit
CIN Input Capacitance TA = 25°C, f = 1 MHz,
VCC = 5.0V 10 pF
COUT Output Capacitance 10 pF
CY7C291A
CY7C292A/CY7C293A
5
AC Test Loads and Waveforms[4]
tPU
tAA tHZCS tACS
50% 50%
tPD
3.0V
5V
OUTPUT
R1250
R2
167
30pF
INCLUDING
JIG AND
SCOPE
GND
90%
10%
90%
10%
<5ns <5ns
5V
OUTPUT
5pF
INCLUDING
JIG AN D
SCOPE
(a) NormalLoad (b) HighZ Load
OUTPUT 2.0V
Equivalent to: THÉ VENIN EQUIVALENT
C291A-4 C291A-5
100C291A-6
R1250
R2
167
ALL INPUT PULSES
CS2CS3
CS1
VCC
SUPPLY
CURRENT
A0A10
ADDRESS
O0-O
7
C291A-7
Switching Characteristics Over the Operating Range[3, 4]
7C291A-20
7C292A-20
7C293A-20
7C291A-25
7C292A-25
7C293A-25
7C291AL-25
7C292AL-25
7C293AL-25
7C291A-35
7C292A-35
7C293A-35
7C291AL-35
7C292AL-35
7C293AL-35
7C291A-50
7C292A-50
7C293A-50
7C291AL-50
7C292AL-50
7C293AL-50
Parameter Description Min. Max. Min. Max. Min. Max. Min. Max. Unit
tAA Address to Output Valid 20 25 35 50 ns
tHZCS1 Chip Select In act ive to High Z 15 15 20 20 ns
tACS1 Chip Select Active to Output Valid 15 15 20 20 ns
tHZCS2 Chip Select In act ive to High Z
(7C293A CS1 Only) [6] 22 27 35 45 ns
tACS2 Chip Select Active to Output Valid
(7C293A CS1 Only) [6] 22 27 35 45 ns
tPU Chip Select Acti v e to Power-Up
(7C293A CS1 Only) 0 0 0 0 ns
tPD Chip Select Inactive to Power-Down
(7C293A CS1 Only) 22 27 35 45 ns
Notes:
6. tHZCS2 and tACS2 r efer to 7C293 A CS1 only.
CY7C291A
CY7C292A/CY7C293A
6
Erasure Characteristics
W avelengths of light less than 4000 Angstroms begin to erase
these PROMs. For this reason, an opaque label should be
placed over the window if the PROM is exposed to sunlight or
fluorescen t lighting for extended periods of time.
The recommended dose of ultraviolet light for erasure is a
wavelength of 2537 Angstroms for a minimum dose (UV inten-
sity x exposure time) of 25 Wsec/cm2. For an ultraviolet lamp
with a 12 mW/cm2 power rating, the exposure time would be
approximately 35 min utes.
These PROMs need to be within 1 inch of the lamp during
erasure. Permanent damage may result if the PROM is ex-
pose d to high-intensity UV light for an extended period of time.
7258 Wsec/cm2 is the recommended maximum dosage.
Pro g ramm in g Inform at ion
Programming support is available from Cypress as well as
from a number of third-party software vendors. For detailed
programming information, including a listing of software pack-
ages, please see the PROM Programming Information located
at the end of this section. Programming a lgorithms can be ob-
tained from any Cypress representative.
Table 1. Mode Selection
Pin Function[7]
Read or Output Disable A10 A0CS3CS2CS1O7 O0
Mode Other A10 A0PGM VFY VPP D7 D0
Read A10 A0VIH VIH VIL O7 O0
Output Disable[8] A10 A0X X VIH High Z
Output Disable A10 A0X VIL XHigh Z
Output Disable A10 A0VIL X X High Z
Program A10 A0VILP VIHP VPP D7 D0
Pro gram Verify A10 A0VIHP VILP VPP O7 O0
Program Inhibit A10 A0VIHP VIHP VPP High Z
Intelligent Program A10 A0VILP VIHP VPP D7 D0
Blank Check Zeros A10 A0VIHP VILP VPP Zeros
Notes:
7. X = “don’t c are” but not to exceed VCC +5%.
8. The power-down mode for the CY7C293A is activated by deselecting CS1.
Figure 1. Programm ing Pin outs
C291A-8 C291A-9
1
2
3
4
5
6
7
8
9
10
11
12
16
17
18
19
20
24
23
22
21
13
14
A8
A7
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
GND
VCC
D7
D6
D4
D5
D3
15
A9
A10
VPP
VFY
PGM
28
4
5
6
7
8
9
10
321 27
1314151617
26
25
24
23
22
21
20
1112 19D018
NC
A0
A4
A3
D7
D6
A2
A1
A10
VPP
VFY
PGM
NC
DIP LCC/PLCC (Opaque Only)
Top Vie w Top Vi ew
7C291A
7C291A
7C292A
7C293A
7C293A
CY7C291A
CY7C292A/CY7C293A
7
Typical DC and AC Characteristics
1.4
1.6
1.0
0.8
4.0 4.5 5.0 5.5 6.0 55 25 125
1.2
1.1
1.2
1.0
0.8
0.6
4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
NORMALIZED SUPPLYCURRENT
vs. SUPPLY VOLTAGE NORMALIZED SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (°C) SUPPLY VOLTAGE (V)
NORMALIZED ACCESSTIME
vs.SUPPLY VOLTAGE
0.6
1.2 1.0
0.9
0.8
TA=25°C
0.4
TA=25°C
f= f
MAX
C291A-10
1.6
1.4
1.2
1.0
0.8
55 125
AMBIENT TEMPERATURE(°C)
NORMALIZED ACCESSTIME
vs.TEMPERATURE
0.6
60
50
40
30
20
10
0 1.0 2.0 3.0
OUTPUT VOL TAGE (V)
30.0
25.0
20.0
15.0
10.0
5.0
0 200 400 600 800
CAPACITANCE (pF)
TYPICAL ACCESSTIME CHANGE
vs.OUTPUT LOADING
4.0 0.0 1000
VCC =4.5V
TA=25°C
25 0
OUTPUT SOURCECURRENT
vs.VOLTAGE
150
175
125
75
50
25
0.0 1.0 2.0 3.0
0
100
OUT PUT VOLTAGE (V)
OUTPUT SINK CURRENT
vs.OUTPUT VOLTAGE
VCC =5.0V
TA=25°C
4.0
C291A-11
1.00
1.02
0.98
0.94
0.92
0.90
025 5075
100
0.88
0.96
ICC vs.CYCLEPERIOD
CYCLEPERIOD (ns)
VCC =5.5V
TA=25°C
CY7C291A
CY7C292A/CY7C293A
8
Orde rin g Inf orm a tio n[9]
Speed
(ns) ICC
(mA) O rderi n g Code Package
Name Package Type Operating
Range
20 120 CY7C291A-20JC J64 28-Lead Pl asti c L e aded Chip Carrier C om mercial
CY7C291A-20PC P13 24-Lead (300-Mil) Mold ed DIP
CY7C291A-20SC S13 24- Lead Molded SOIC
CY7C291A-20WC W14 24-Lead (300-Mil) Windowed CerDIP
25 60 CY7C291AL-25JC J64 28-Lead Plastic L e aded Chip Carrier C om mercial
CY7C291AL-25PC P13 24-Lead ( 300-Mil) Molded DIP
CY7C291AL-25WC W14 24-Lead (300-Mil) Window ed CerDIP
90 CY7C291A-25JC J64 28-Lead Pl asti c L e aded Chip Carrier
CY7C291A-25PC P13 24-Lead (300-Mil) Mold ed DIP
CY7C291A-25SC S13 24- Lead Molded SOIC
CY7C291A-25WC W14 24-Lead (300-Mil) Windowed CerDIP
120 CY7C291A-25DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C291A-25LMB L64 28- Square Leadless Chip Carrier
CY7C291A-25QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C291A-25TMB T73 24-Lead Windowed Cerpack
CY7C291A-25WMB W14 24-Lead (300-Mil) Windowed CerDIP
30 120 CY7C291A-30DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C291A-30LMB L64 28- Square Leadless Chip Carrier
CY7C291A-30QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C291A-30TMB T73 24-Lead Windowed Cerpack
CY7C291A-30WMB W14 24-Lead (300-Mil) Windowed CerDIP
35 60 CY7C291AL-35JC J64 28-Lead Plastic L e aded Chip Carrier C om mercial
CY7C291AL-35PC P13 24-Lead ( 300-Mil) Molded DIP
CY7C291AL-35WC W14 24-Lead (300-Mil) Window ed CerDIP
90 CY7C291A-35SC S13 24- Lead Molded SOIC Commercial
CY7C291A-35PC P13 24-Lead (300-Mil) Mold ed DIP
CY7C291A-35WC W14 24-Lead (300-Mil) Windowed CerDIP
120 CY7C291A-35DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C291A-35LMB L64 28- Square Leadless Chip Carrier
CY7C291A-35QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C291A-35TMB T73 24-Lead Windowed Cerpack
CY7C291A-35WMB W14 24-Lead (300-Mil) Windowed CerDIP
Notes:
9. Most of these products are ava ilable in industrial temperature range. Contact a Cypress representative for specifications and pro duc t
availability.
CY7C291A
CY7C292A/CY7C293A
9
50 60 CY7C291AL-50JC J64 28-Lead Plastic L e aded Chip Carrier C om mercial
CY7C291AL-50PC P13 24-Lead ( 300-Mil) Molded DIP
CY7C291AL-50WC W14 24-Lead (300-Mil) Window ed CerDIP
90 CY7C291A-50SC S13 24- Lead Molded SOIC Commercial
CY7C291A-50PC P13 24-Lead (300-Mil) Mold ed DIP
CY7C291A-50WC W14 24-Lead (300-Mil) Windowed CerDIP
90 CY7C291A-50DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C291A-50LMB L64 28- Square Leadless Chip Carrier
CY7C291A-50QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C291A-50TMB T73 24-Lead Windowed Cerpack
CY7C291A-50WMB W14 24-Lead (300-Mil) Windowed CerDIP
20 120 CY7C292A-20DC D12 24-Lead (600-Mil) CerDIP Commercial
CY7C292A-20PC P11 24-Lead (600-Mil) Mold ed DIP
25 120 CY7C292A-25DC D12 24-Lead (600-Mil) CerDIP Commercial
CY7C292A-25PC P11 24-Lead (600-Mil) Mold ed DIP
CY7C292A-25DMB D12 24-Lead (600-Mil) CerDIP Military
30 120 CY7C292A-30DMB D12 24-Lead (600-Mil) CerDIP Military
35 60 CY7C292AL-35PC P11 24 -Lead (600-Mil) Mold ed DIP Commercial
90 CY7C292A-35DC D12 24-Lead (600-Mil) CerDIP Commercial
CY7C292A-35PC P11 24-Lead (600-Mil) Mold ed DIP
120 CY7C292A-35DMB D12 24-Lead (600-Mil) CerDIP Military
50 60 CY7C292AL-50PC P11 24 -Lead (600-Mil) Mold ed DIP Commercial
90 CY7C292A-50DC D12 24-Lead (600-Mil) CerDIP Commercial
CY7C292A-50PC P11 24-Lead (600-Mil) Mold ed DIP
120 CY7C292A-50DMB D12 24-Lead (600-Mil) CerDIP Military
20 120 CY7C293A-20PC P13 24-Lead (300-Mil) Mold ed DIP Commercial
CY7C293A-20WC W14 24-Lead (300-Mil) Windowed CerDIP
25 120 CY7C293A-25PC P13 24-Lead (300-Mil) Mold ed DIP Commercial
CY7C293A-25WC W14 24-Lead (300-Mil) Windowed CerDIP
CY7C293A-25DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C293A-25LMB L64 28- Square Leadless Chip Carrier
CY7C293A-25QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C293A-25WMB W14 24-Lead (300-Mil) Windowed CerDIP
Orde rin g Inf orm a tio n[9] (Conti nued)
Speed
(ns) ICC
(mA) Ordering Code Package
Name Package Type Operating
Range
CY7C291A
CY7C292A/CY7C293A
10
30 120 CY7C293A-30DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C293A-30LMB L64 28- Square Leadless Chip Carrier
CY7C293A-30QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C293A-30WMB W14 24-Lead (300-Mil) Windowed CerDIP
35 60 CY7C293AL-35PC P13 24-Lead ( 300-Mil) Molded DIP Commercial
CY7C293AL-35WC W14 24-Lead (300-Mil) Window ed CerDIP
90 CY7C293A-35PC P13 24-Lead (300-Mil) Mold ed DIP Commercial
CY7C293A-35WC W14 24-Lead (300-Mil) Windowed CerDIP
90 CY7C293A-35DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C293A-35LMB L64 28- Square Leadless Chip Carrier
CY7C293A-35QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C293A-35WMB W14 24-Lead (300-Mil) Windowed CerDIP
50 60 CY7C293AL-50PC P13 24-Lead ( 300-Mil) Molded DIP Commercial
CY7C293AL-50WC W14 24-Lead (300-Mil) Window ed CerDIP
90 CY7C293A-50PC P13 24-Lead (300-Mil) Mold ed DIP Commercial
CY7C293A-50WC W14 24-Lead (300-Mil) Windowed CerDIP
90 CY7C293A-50DMB D14 24-Lead (300-Mil) CerDIP Military
CY7C293A-50LMB L64 28- Square Leadless Chip Carrier
CY7C293A-50QMB Q64 28-Pin Windowed Leadless Chip Carrier
CY7C293A-50WMB W14 24-Lead (300-Mil) Windowed CerDIP
Orde rin g Inf orm a tio n[9] (Conti nued)
Speed
(ns) ICC
(mA) Ordering Code Package
Name Package Type Operating
Range
CY7C291A
CY7C292A/CY7C293A
11
MIL ITARY SPECIFICATIONS
Group A Subgroup Testing
Document #: 38-00 075-G
DC Characteristics
Parameter Subgroups
VOH 1, 2, 3
VOL 1, 2, 3
VIH 1, 2, 3
VIL 1, 2, 3
IIX 1, 2, 3
IOZ 1, 2, 3
ICC 1, 2, 3
ISB[10] 1, 2, 3
Switching Characteristics
Parameter Subgroups
tAA 7, 8, 9, 10, 11
tACS1[11] 7, 8, 9, 10, 11
tACS2[10] 7, 8, 9, 10, 11
Notes:
10 . 7C2 93A only.
11. 7C2 91A and 7C292A only.
SMD Cross Reference
SMD
Number Suffix Cypress
Number
5962-87650 01KX CY7C291-50TMB
5962-87650 01LX CY7C291-50WMB
5962-87650 013X CY7C291-50QMB
5962-87650 03KX CY7C291-35TMB
5962-87650 03LX CY7C291-35WMB
5962-87650 033X CY7C291-35QMB
5962-88680 01LX CY7C293A-50WMB
5962-88680 01KX CY7C293A-50TMB
5962-88680 013X CY7C293A-50QMB
5962-88680 02LX CY7C293A-35WMB
5962-88680 02KX CY7C293A-35TMB
5962-88680 023X CY7C293A-35QMB
5962-88680 03LX CY7C293A-30WMB
5962-88680 03KX CY7C293A-30TMB
5962-88680 033X CY7C293A-30QMB
5962-88680 04LX CY7C293A-25WMB
5962-88680 04KX CY7C293A-25TMB
5962-88680 043X CY7C293A-25QMB
5962-88734 02JX CY7C292A-45DMB
5962-88734 02KX CY7C291A-45KMB
5962-88734 02LX CY7C291A-45DMB
5962-88734 023X CY7C291A-45LMB
5962-88734 03JX CY7C292A-35DMB
5962-88734 03KX CY7C291A-35KMB
5962-88734 03LX CY7C291A-35DMB
5962-88734 033X CY7C291A-35LMB
5962-88734 04JX CY7C292A-25DMB
5962-88734 04KX CY7C291A-25KMB
5962-88734 04LX CY7C291A-25DMB
5962-88734 043X CY7C291A-25LMB
CY7C291A
CY7C292A/CY7C293A
12
Package Diagrams
24-Lead (600-Mil) CerDIP D12
MIL-STD-1835 D-3 Config.A 28-Square LeadlessChipCarrier L64
MIL-STD-1835 C-4
24-Lead (300-Mil) CerDIP D14
MIL-STD-1835 D-9Config.A
CY7C291A
CY7C292A/CY7C293A
13
Package Diagrams (Continued)
24-Lead (600-Mil) MoldedDIP P11
24-Lead (300-Mil) Molded DIP P13/P13A
CY7C291A
CY7C292A/CY7C293A
14
Package Diagrams (Continued)
28-Pin Windowed LeadlessChipCarrier Q64
MIL-STD-1835 C-4
24-Lead (300-Mil) Molded SOIC S13
CY7C291A
CY7C292A/CY7C293A
© Cypress Semiconductor Corporation, 1993. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry othe r than circui try embodi ed in a Cypress Semicondu ctor product. Nor does it convey or im ply an y li cense under patent or other rights . Cypress Semicondu ctor does not authori ze
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in s ignificant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
Package Diagrams (Continued)
24-Lead Windowed Cerpack T73
24-Lead (300-Mil) WindowedCerDIP W14
MIL-STD-1835 D-9 Config.A