Miniature PCB Relays
8 - 10 - 12 - 16 A
Medical and
dentistry
Control panels
Panels for electrical
distribution
Toys
Automation for
blinds, grilles
and shutters
Door and gate
openers
Electronic
circuit boards
Vending
machines
40
SЕRIES
FINDER reserves the right to alter characteristics at any time without notice. FINDER assumes no liability for damage to persons or property, caused as a result of the incorrect use or application of its products.
A
Power relays 1 and 2 pole for direct PCB or
socket mount
Type 40.31/51
- 1 CO 12 A (3.5mm pin pitch)
- 1 CO 12 A (5.0mm pin pitch)
Type 40.52
- 2 CO 8A (5.0mm pin pitch)
Type 40.61
- 1 CO 16 A (5.0mm pin pitch)
• Pin length 3.5 mm for PCB mount
• Pin length 5.3 mm for Plug-in mount
• DC coils (650 mW or 500 mW)
• Cadmium-free contact material available
• 8 mm Creepage and Clearance, 6 kV (1.2/50µs)
between coil and contact
• Meets EN 60335-1 glow wire requirements
• 95 series sockets for PCB or 35 mm rail
mounting (EN 60715) with Screw, Screwless or
Push-in terminals
• Coil Indication and EMC suppression modules
99 series and Timer module 86.30 options
• Environmental protection:
RT II - flux proof (Standard)
RT III - wash tight (Option)
40.31/51 40.52 40.61
• 1 CO 12 A on PCB, 10 A with
socket
• 3.5mm pin pitch (40.31),
5.0mm pin pitch (40.51)
• PCB or 95 Series socket mount
• 2 CO 8 A
• 5.0mm pin pitch
• PCB or 95 Series socket mount
• 1 CO 16 A
• 5.0mm pin pitch
• PCB or 95 Series socket mount
40.31
40.51
Copper side view
Pin length 3.5mm for PCB only
Pin length 5.3mm for PCB or
sockets
See ordering information
Copper side view
Pin length 5.3mm for PCB or
sockets
See ordering information
Copper side view
Pin length 3.5mm for PCB only
Pin length 5.3mm for PCB or
sockets
See ordering information
* Mounted on sockets ≤10A
** With the AgSnO2 material the
maximum peak
current is 120A- 5ms on normally open
contact.
For UL ratings see:
“General technical information” page V
For outline drawing see page 12
Contact specification
Contact configuration 1 CO (SPDT) 2 CO (DPDT) 1 CO (SPDT)
Rated current/Maximum peak current A 12*/20 8/15 16/30**
Rated voltage/
Maximum switching voltage VAC 250/400 250/400 250/400
Rated load AC1 VA 3000 2000 4000
Rated load AC15 (230VAC) VA 1000 750 1000
Single phase motor rating (230VAC) kW 0.55 0.37 0.55
Breaking capacity DC1: 30/110/220V A 12/0.6/0.25 8/0.6/0.25 16/0.6/0.25
Minimum switching load mW (V/mA) 300 (5/5) 300 (5/5) 500 (10/5)
Standard contact material AgNi AgNi AgCdO
Coil specification
Nominal voltage (UN) VAC (50/60Hz) — — —
VDC 5 - 6 - 7 - 9 - 12 - 14 - 18 - 21 - 24 - 28 - 36 - 48 - 60 - 90 - 110 - 125
Rated power DC/sensitive DC W 0.65/0.5 0.65/0.5 0.65/0.5
Operating range AC ———
DC/sensitive DC (0.73…1.5)UN/(0.73…1.5)UN(0.73…1.5)UN/(0.73…1.5)UN(0.73…1.5)UN/(0.8…1.5)UN
Holding voltage DC 0.4
UN
0.4
UN
0.4
UN
Must drop-out voltage DC 0.1
UN
0.1
UN
0.1
UN
Technical data
Mechanical life cycles 10·10610·10610·106
Electrical life at rated load AC1 cycles 200·103100·103100·103
Operate/release time ms 7/3 (10/3 sensitive) 7/3 (12/4 sensitive) 7/3 (10/3 sensitive)
Insulation between coil
and contacts (1.2/50µs) kV 6 (8mm) 6 (8mm) 6 (8mm)
Dielectric strength
between open contacts VAC 1000 1000 1000
Ambient temperature range °C –40…+85 –40…+85 –40…+85
Environmental protection RT II*** RT II*** RT II***
Approvals (according to type)
*** See general technical information “Guidelines for automatic flow solder processes” page II.
3
XI-2018, www.findernet.com
40
SERIES
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
A
Power relays 1 and 2 pole for direct PCB or
socket mount
Type 40.31/51
- 1 CO 10A (3.5mm pin pitch)
- 1 CO 10A (5.0mm pin pitch)
Type 40.52
- 2 CO 8A (5.0mm pin pitch)
Type 40.61
- 1 CO 16 A (5.0mm pin pitch)
• AC or DC coils according to type
• Cadmium-free contact material
• 8 mm Creepage and Clearance, 6 kV (1.2/50µs)
between coil and contact
• Meets EN 60335-1 glow wire requirements
• 95 series sockets for PCB or 35 mm rail
mounting (EN 60715) with Screw, Screwless or
Push-in terminals
• Coil Indication and EMC suppression modules
99 series and Timer module 86.30 options
• Environmental protection:
RT II - flux proof (Standard)
RT III - wash tight (Option)
* With the AgSnO2 material the
maximum peak
current is 120A- 5ms on normally open
contact.
40.31/51 40.52 40.61
• 1 CO 10 A
• 3.5mm pin pitch (40.31),
5.0mm pin pitch (40.51)
• PCB or 95 Series socket mount
• 2 CO 8 A
• 5.0mm pin pitch
• PCB or 95 Series socket mount
• 1 CO 16 A
• 5.0mm pin pitch
• PCB or 95 Series socket mount
40.31
40.51
Copper side view
Pin length 5.3mm for
PCB or sockets
Copper side view
Pin length 5.3mm for
PCB or sockets
Copper side view
Pin length 5.3mm for
PCB or sockets
For UL ratings see:
“General technical information” page V
For outline drawing see page 12
Contact specification
Contact configuration 1 CO (SPDT) 2 CO (DPDT) 1 CO (SPDT)
Rated current/Maximum peak current A 10/20 8/15 16/30*
Rated voltage/
Maximum switching voltage VAC 250/400 250/400 250/400
Rated load AC1 VA 2500 2000 4000
Rated load AC15 (230VAC) VA 500 400 750
Single phase motor rating (230VAC) kW 0.37 0.3 0.55
Breaking capacity DC1: 30/110/220V A 10/0.3/0.12 8/0.3/0.12 16/0.3/0.12
Minimum switching load mW (V/mA) 300 (5/5) 300 (5/5) 500 (10/5)
Standard contact material AgNi AgNi AgCdO
Coil specification
Nominal voltage (UN) VAC (50/60Hz) 6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240
VDC —
5 - 6 - 7 - 9 - 12 - 14 - 18 - 21 - 24 -
28 - 36 - 48 - 60 - 90 - 110 - 125
—
Rated power AC/DC/sens. DC VA (50Hz)/W/W 1.2/—/— 1.2/0.65/0.5 1.2/—/—
Operating range AC (0.8…1.1)UN(0.8…1.1)UN(0.8…1.1)UN
DC/sens. DC — (0.73…1.5)UN/(0.73…1.5)UN
—
Holding voltage AC/DC 0.8
UN
/— 0.8
UN
/0.4
UN
0.8UN/—
Must drop-out voltage AC/DC 0.2
UN
/— 0.2
UN
/0.1
UN
0.2UN/—
Technical data
Mechanical life cycles 10·10610·10610·106
Electrical life at rated load AC1 cycles 200·103100·103100·103
Operate/release time ms 7/3 7/3 - (12/4 sensitive) 7/3
Insulation between coil
and contacts (1.2/50µs) kV 6 (8 mm) 6 (8 mm) 6 (8mm)
Dielectric strength
between open contacts VAC 1000 1000 1000
Ambient temperature range °C –40…+85 –40…+85 –40…+85
Environmental protection RT II** RT II** RT II**
Approvals (according to type)
** See general technical information “Guidelines for automatic flow solder processes” page II.
4
XI-2018, www.findernet.com
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
40
SERIES
A
Power relays 1 and 2 pole for direct PCB or
socket mount
Type 40.62
- 2 CO 10A (5.0 mm pin pitch)
- DC coils (650 mW or 500 mW)
- Meets EN 60335-1 glow wire requirements
Type 40.11
- 1 CO 10 A - flat pack
- DC (sensitive) coils
Type 40.xx.6
- Bistable versions of the types 40.31, 40.51,
40.52 and 40.61
- Bistable (single coil)
• Cadmium-free contact material available
• 8 mm Creepage and Clearance, 6 kV (1.2/50µs)
between coil and contact
• 95 series sockets for PCB or 35 mm rail mounting
(EN 60715) with Screw, Screwless or Push-in
terminals
• Environmental protection:
RT II - flux proof (Standard)
RT III - wash tight (Option)
40.62 40.xx.6 40.11
• 2 CO 10 A
• 5.0 mm pin pitch
• PCB or 95 Series sockets mount
• Bistable (single coil)
• 3.5 or 5.0 mm pin pitch
• PCB or 95 Series socket mount
• 1 CO 10 A
• PCB mount 12.7 mm high
Copper side view
Pin length 5.3mm for
PCB or sockets
Bistable version (1 coil) types:
40.31.6…
40.51.6…
40.52.6…
40.61.6…
For wiring diagrams see page 11
Pin length 5.3mm for
PCB or sockets
Copper side view
Pin length 3.5mm for PCB
For UL ratings see:
“General technical information” page V
For outline drawing see page 12
Contact specification
Contact configuration 2 CO (DPDT) 1 CO (SPDT)
Rated current/Maximum peak current A 10/20 10/20
Rated voltage/
Maximum switching voltage VAC 250/400 See relays 250/400
Rated load AC1 VA 2500 40.31 2500
Rated load AC15 (230VAC) VA 750 40.51 500
Single phase motor rating (230VAC) kW 0.37 40.52 0.37
Breaking capacity DC1: 30/110/220V A 10/0.6/0.25 40.61 10/0.3/0.12
Minimum switching load mW (V/mA) 300 (5/5) page 4 300 (5/5)
Standard contact material AgNi AgCdO
Coil specification
Nominal voltage (UN) VAC (50/60Hz) —
5 - 6 - 12 - 24 - 48 - 110
—
VDC
5 - 6 - 7 - 9 - 12 - 14 - 18 - 21 - 24
- 28 - 48 - 60 - 110 - 125 6 - 12 - 24 - 48 - 60
Rated power AC/DC/sens. DC VA (50Hz)/W/W —/0.65/0.5 1.0/1.0/— —/—/0.5
Operating range AC — (0.8…1.1)UN—
DC/sens. DC (0.73…1.5)UN/(0.73..1.5) UN(0.8…1.1)UN/— —/(0.73…1.75)UN
Holding voltage AC/DC —/0.4UN— —/0.4UN
Must drop-out voltage AC/DC —/0.1UN— —/0.1UN
Technical data
Mechanical life cycles 10·106See relays 20·106
Electrical life at rated load AC1 cycles 100·10340.31 200·103
Operate/release time ms 7/3 (12/4 sensitive) 40.51 12/4
Insulation between coil
and contacts (1.2/50µs) kV 6 (8mm) 40.52 6 (8mm)
Dielectric strength
between open contacts VAC 1000 40.61 1000
Ambient temperature range °C –40…+85 Min. impulse duration –40…+70
Environmental protection RT II ≥20ms RT I**
Approvals (according to type)
** See general technical information “Guidelines for automatic flow solder processes” page II.
5
XI-2018, www.findernet.com
40
SERIES
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
A
Ordering information
Example: 40 series PCB relay, 2 CO, 230VAC coil.
A B C D
4 0 . 5 2 . 8 . 2 3 0 . 0 0 0 0
Series
Type
1 = PCB - 3.5mm pinning, flat
3 = PCB/Plug-in - 3.5mm pinning
5 = PCB/Plug-in - 5mm pinning
6 = PCB/Plug-in - 5mm pinning
No. of poles
1 = 1 pole
2 = 2 pole
Coil version
6 = AC/DC bistable
7 = Sensitive DC, 0.5W
8 = AC (50/60Hz)
9 = Standard DC, 0.65W
Coil voltage
See coil specifications
A: Contact material
See table below
B: Contact circuit
0 = CO (nPDT)
3 = NO (nPST)
D: Special versions
0 = Standard
1 = Wash tight (RTIII)
3 = High temperature (+125°C) wash
tight
C: Options
0 = Pin length 5.3mm (Plug-in relays)
2 = Pin length 3.5mm (PCB relays)
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Terminal pin Type Coil version A B C D
PCB relay,
pin length 3.5mm
40.11 Sensitive DC 2 (AgCdO) - 4 (AgSnO2)000
40.31/51 Standard DC/sensitive DC 1 (AgNi) 0 - 3 2 0 - 1
40.61 Standard DC/sensitive DC 1 (AgNi) - 2 (AgCdO) 0 - 3 2 0 - 1
PCB/Plug-in relay
pin length 5.3mm
40.31/51 AC/sensitive DC 0 (AgNi) - 2 (AgCdO) - 5 (AgNi+Au) 0 - 3 0 0 - 1
40.31/51 Standard DC 0 (AgNi) - 2 (AgCdO) - 5 (AgNi+Au) 0 - 3 0 0 - 1 - 3
40.52 AC/sensitive DC 0 (AgNi) - 2 (AgCdO) - 5 (AgNi+Au) 0 - 3 0 0 - 1
40.52 Standard DC 0 (AgNi) - 2 (AgCdO) - 5 (AgNi+Au) 0 - 3 0 0 - 1 - 3
40.61 AC/sensitive DC 0 (AgCdO) - 4 (AgSnO2)0 - 3 0 0 - 1
40.61 Standard DC 0 (AgCdO) - 4 (AgSnO2)0 - 3 0 0 - 1 - 3
40.62 Standard DC/sensitive DC 0 (AgNi) - 4 (AgSnO2)000 - 1
40.31/51/52 Bistable 0 (AgNi) 000
40.61 Bistable 0 (AgCdO) 000
6
XI-2018, www.findernet.com
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
40
SERIES
A
Technical data
Insulation according to EN61810-1
1 pole 2 pole
Nominal voltage of supply system VAC 230/400 230/400
Rated insulation voltage VAC 250 400 250 400
Pollution degree 3 2 3 2
Insulation between coil and contact set
Type of insulation Reinforced (8mm) Reinforced (8mm)
Overvoltage category III III
Rated impulse voltage kV (1.2/50µs) 6 6
Dielectric strength VAC 4000 4000
Insulation between adjacent contacts (40.52, page 4)
Type of insulation — Basic
Overvoltage category — II
Rated impulse voltage kV (1.2/50µs) — 2.5
Dielectric strength VAC — 2000
Insulation between adjacent contacts (40.52, page 3 + 40.62)
Type of insulation — Basic
Overvoltage category III
Rated impulse voltage kV (1.2/50µs) — 4
Dielectric strength VAC — 2500
Insulation between open contacts
Type of disconnection Micro-disconnection Micro-disconnection
Dielectric strength V AC/kV (1.2/50µs) 1000/1.5 1000/1.5
Insulation between coil terminals
Rated impulse voltage (surge) differential mode
(according to EN 61000-4-5) kV(1.2/50µs) 2
Other data
Bounce time: NO/NC ms 2/5
Vibration resistance (10…150)Hz: NO/NC g 20/5 (1 changeover) 15/4 (2 changeover)
Shock resistance NO/NC g 20/13 (1 changeover) 20/12 (2 changeover)
Power lost to the environment without contact current W 0.65
with rated current W 1.2 (40.11/31/51) 2 (40.61/52/62)
Recommended distance between relays mounted on PCB mm ≥5
7
XI-2018, www.findernet.com
40
SERIES
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
A
Contact specification
F 40.1 - Electrical life (AC) v contact current
Types 40.31/51/61 (page 3)
F 40.2 - Electrical life (AC) v contact current
Type 40.52 (page 3)
Cycles
Resistive load - cosϕ = 1
Inductive load AC15
Cycles
Resistive load - cosϕ = 1
Inductive load AC15
F 40.3 - Electrical life (AC) v contact current
Types 40.31/51/61 (page 4)
F 40.4 - Electrical life (AC) v contact current
Type 40.52 (page 4)
Cycles
Limit for 40.31/51
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
Cycles
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
F 40.5 - Electrical life (AC) v contact current
Type 40.11 (page 5)
F 40.6 - Electrical life (AC) v contact current
Type 40.62 (page 5)
Cycles
Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
12
8
Cycles
Resistive load - cosϕ = 1
Limit for 40.31/51
Inductive load AC15
8
XI-2018, www.findernet.com
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
40
SERIES
A
Contact specification
H 40.1 - Maximum DC1 breaking capacity
Types 40.31/51/52/61 (page 3)
H 40.2 - Maximum DC1 breaking capacity
Types 40.31/51/52/61 (page 4) and 40.11 (page 5)
DC breaking current (A)
DC voltage (V)
40.52 - 2 contacts in series
single contact
40.61 current limit
40.31/51 current limit
40.52 current limit
DC breaking current (A)
DC voltage (V)
40.52 - 2 contacts in series
single contact
40.61 current limit
40.11/31/51 current limit
40.52 current limit
H 40.6 - Maximum DC1 breaking capacity
Type 40.62 (page 5)
DC breaking current (A)
DC voltage (V)
• When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of ≥100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
2 contacts in series
single contact
9
XI-2018, www.findernet.com
40
SERIES
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
A
Coil specifications
DC coil data - 0.65 W standard (types 40.31/51/52/61/62)
Nominal
voltage
Coil
code
Operating range Resistance Rated coil
consumption
UNUmin Umax RI at UN
V V V ΩmA
59.005 3.65 7.5 38 130
69.006 4.4 9 55 109
79.007 5.1 10.5 75 94
99.009 6.6 13.5 125 72
12 9.012 8.8 18 220 55
14 9.014 10.2 21 300 47
18 9.018 13.1 27 500 36
21 9.021 15.3 31.5 700 30
24 9.024 17.5 36 900 27
28 9.028 20.5 42 1200 23
36 9.036 26.3 54 2000 18
48 9.048 35 72 3500 14
60 9.060 43.8 90 5500 11
90 9.090 65.7 135 12500 7.2
110 9.110 80.3 165 18000 6.2
125 9.125 91.2 188 23500 5.3
DC coil data - 0.5 W sensitive (types 40.31/51/52/61/62)
Nominal
voltage
Coil
code
Operating range Resistance Rated coil
consumption
UNUmin Umax RI at UN
V V V ΩmA
57.005 3.7 7.5 50 100
67.006 4.4 9 75 80
77.007 5.1 10.5 100 70
97.009 6.6 13.5 160 56
12 7.012 8.8 18 288 42
14 7.014 10.2 21 400 35
18 7.018 13.2 27 650 27.7
21 7.021 15.4 31.5 900 23.4
24 7.024 17.5 36 1150 21
28 7.028 20.5 42 1600 17.5
36 7.036 26.3 54 2600 13.8
48 7.048 35 72 4800 10
60 7.060 43.8 90 7200 8.4
90 7.090 65.7 135 16200 5.6
110 7.110 80.3 165 23500 4.7
125 7.125 91.2 188 32000 3.9
* Umin = 0.8UN for 40.61
DC coil data - 0.5 W sensitive (types 40.11)
Nominal
voltage
Coil
code
Operating range Resistance Rated coil
consumption
UNUmin Umax RI at UN
V V V ΩmA
67.006 4.4 10.5 75 80
12 7.012 8.8 21 300 40
24 7.024 17.5 42 1200 20
48 7.048 35 84 4600 10.4
60 7.060 43.8 105 7200 8.3
AC coil data (types 40.31/51/52/61)
Nominal
voltage
Coil
code
Operating range Resistance Rated coil
consumption
UNUmin Umax RI at UN (50Hz)
V V V ΩmA
68.006 4.8 6.6 21 168
12 8.012 9.6 13.2 80 90
24 8.024 19.2 26.4 320 45
48 8.048 38.4 52.8 1350 21
60 8.060 48 66 2100 16.8
110 8.110 88 121 6900 9.4
120 8.120 96 132 9000 8.4
230 8.230 184 253 28000 5
240 8.240 192 264 31500 4.1
AC/DC coil data - bistable (types 40.31/51/52/61)
Nominal
voltage
Coil
code
Operating range Resistance Rated coil
consumption
DC: Release
resistance**
UNUmin Umax RI at UNRDC
V V V ΩmA Ω
56.005 4 5.5 23 215 37
66.006 4.8 6.6 33 165 62
12 6.012 9.6 13.2 130 83 220
24 6.024 19.2 26.4 520 40 910
48 6.048 38.4 52.8 2100 21 3,600
110 6.110 88 121 11000 10 16,500
** RDC=Resistance in DC, RAC=1.3xRDC 1W
10
XI-2018, www.findernet.com
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
40
SERIES
A
Contact specification
R 40 - DC coil operating range v ambient temperature
Standard coil
R 40 - DC coil operating range v ambient temperature
Sensitive coil, types 40.31/51/52/61/62
40.61
40.31/51/52/62
R 40 - DC coil operating range v ambient temperature
Sensitive coil, type 40.11
R 40 - AC coil operating range v ambient temperature
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
Wiring diagram for 40 series bistable coil version
AC Operation DC Operation
On momentary closure of the SET switch the relay is magnetised through
the diode and the relay contacts transfer to the set position and remain in
this position.
On momentary closure of the RESET switch the relay is demagnetised
through limiting resistor (RAC) and the contacts return to the reset position.
On momentary closure of the SET switch the relay is magnetised and the
relay contacts transfer to the set position and remain in this position.
On momentary closure of the RESET switch the relay is demagnetised
through limiting resistor (RDC) and the contacts return to the reset position.
Notes: The minimum SET or RESET impulse time is 20ms. The maximum time can be continuous. In practice, always ensure that the SET and RESET
contacts cannot be operated simultaneously.
11
XI-2018, www.findernet.com
40
SERIES
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
A
Outline drawings
Types 40.31/51/52/61/62 (page 3 e 4) Types 40.31/51/52/61 (page 4) Type 40.11 (page 5)
* (3.5 or 5.3mm) see ordering code
12
XI-2018, www.findernet.com
40 SERIES
PCB/Plug-in relays 8 - 10 - 12 - 16A
40
SERIES
A
See page 14
95.P5
Module Socket Relay Description Mounting Accessories
99.02 95.P3 40.31 Push-in terminal sockets
- For fast cable connection
- Top terminals - Contacts
- Bottom terminals - Coil
Panel or 35mm rail
(EN60715) mount
- Coil indication and EMC
suppression modules
- Jumper link
- Timer modules
- Plastic retaining and release
clip
95.P5 40.51
40.52
40.61
40.62
See page 16
95.05
Module Socket Relay Description Mounting Accessories
99.02 95.03 40.31 Screw terminal (Box clamp) socket
- Top terminals - Contacts
- Bottom terminals - Coil
Panel or 35mm rail
(EN60715) mount
- Coil indication and EMC
suppression modules
- Jumper link
- Timer modules
- Plastic retaining and release
clip
95.05 40.51
40.52
40.61
40.62
95.55
See page 17
Module Socket Relay Description Mounting Accessories
99.02 95.55 40.51
40.52
40.61
40.62
Screwless terminal socket
- Top terminals - Contacts
- Bottom terminals - Coil
Panel or 35mm rail
(EN60715) mount
- Coil indication and EMC
suppression modules
- Timer modules
- Plastic retaining and release
clip
95.85.3
See page 18
Module Socket Relay Description Mounting Accessories
99.80 95.83.3 40.31 Screw terminal (Box clamp) socket
- Top terminals - NO and COM
Contacts
- Bottom terminals - Coil and NC
Contacts
Panel or 35mm rail
(EN60715) mount
- Coil indication and EMC
suppression modules
- Jumper link
- Plastic retaining and release
clip
95.85.3 40.51
40.52
40.61
40.62
95.95.3
See page 19
Module Socket Relay Description Mounting Accessories
99.80 95.93.3 40.31 Screw terminal (Box clamp) socket
- Top terminals - Contacts
- Bottom terminals - Coil
Panel or 35mm rail
(EN60715) mount
- Coil indication and EMC
suppression modules
- Jumper link
- Plastic retaining and release
clip
95.95.3 40.51
40.52
40.61
40.62
95.65
See page 20
Module Socket Relay Description Mounting Accessories
99.01 95.63 40.31 Screw terminal (Box clamp) socket
- Top terminals - Contacts
- Bottom terminals - Coil
Panel or 35mm rail
(EN60715) mount
- Metal retaining clip
95.65 40.51
40.52
40.61
40.62
See page 21
95.13.2
Module Socket Relay Description Mounting Accessories
—95.13.2 40.31 PCB socket PCB mounting - Metal retaining clip
- Plastic retaining clip
—95.15.2 40.51
40.52
40.61
40.62
13
XI-2018, www.findernet.com
40
SERIES
95 SERIES
Socket overview for 40 series relays
A
95.P5
Approvals
(according to type):
095.91.3
060.48
Push-in terminals socket panel or 35mm rail mount 95.P3 95.P5
For relay type 40.31 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip
095.71
Plastic retaining and release clip
(supplied with socket - packaging code SPA)
095.91.3
8-way jumper link 097.58
2-way jumper link (12.5
mm pitch) 097.52
2-way jumper link (4.6
mm pitch) 097.42
Marker tag holder (for tags 060.48 type) 097.00
Identification tag 095.00.4
Modules (see table below) 99.02
Timer modules (see table below) 86.30
Sheet of marker tags for plastic retaining and release clip
095.91.3 and for marker tag holder 097.00, 48 tags,
6x12mm, for CEMBRE thermal transfert printer 060.48
Technical data
Rated values
10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV
Protection category IP 20
Ambient temperature °C –40…+70 (see diagram L95)
Wire strip length mm 8
Min. wire size for 95.P3 and 95.P5 sockets solid wire stranded wire
mm20.5 0.5
AWG 21 21
Max. wire size for 95.P3 and 95.P5 sockets solid wire stranded wire
mm22x1.5 / 1x2.5 2x1.5 / 1x2.5
AWG 2x16 / 1x14 2x16 / 1x14
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
L 95 - Total socket current v ambient temperature
A2
A1 COIL
11 COM
NO
NC
14
12
95.P3
95.P5
95.P3 95.P5
Total socket current (A)
097.58
8-way jumper link for 95.P3 and 95.P5 sockets 097.58
Rated values 10A - 250V
097.52
2-way jumper link for 95.P3 and 95.P5 sockets 097.52
Rated values 10A - 250V
14
XI-2018, www.findernet.com
95 SERIES
Socket and accessories for 40 series relays
40
SERIES
A
097.42
2-way jumper link for 95.P3 and 95.P5 sockets 097.42
Rated values 10A - 250V
097.00
Marker tag holder for 95.P3 and 95.P5 sockets 097.00
86.30
86 series timer modules
(12…24)VAC/DC; Bi-function: AI, DI; (0.05s…100h) 86.30.0.024.0000
(110…125)VAC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.120.0000
(230…240)VAC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.240.0000
Approvals (according to type):
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
99.02 coil indication and EMC suppression modules for 95.P3 and 95.P5 sockets
Diode (+A1, standard polarity) (6…220)VDC 99.02.3.000.00
LED (6…24)VDC/AC 99.02.0.024.59
LED (28…60)VDC/AC 99.02.0.060.59
LED (110…240)VDC/AC 99.02.0.230.59
LED + Diode (+A1, standard polarity) (6…24)VDC 99.02.9.024.99
LED + Diode (+A1, standard polarity) (28…60)VDC 99.02.9.060.99
LED + Diode (+A1, standard polarity) (110…220)VDC 99.02.9.220.99
LED + Varistor (6…24)VDC/AC 99.02.0.024.98
LED + Varistor (28…60)VDC/AC 99.02.0.060.98
LED + Varistor (110…240)VDC/AC 99.02.0.230.98
RC circuit (6…24)VDC/AC 99.02.0.024.09
RC circuit (28…60)VDC/AC 99.02.0.060.09
RC circuit (110…240)VDC/AC 99.02.0.230.09
Residual current by-pass (110…240)VAC 99.02.8.230.07
15
XI-2018, www.findernet.com
40
SERIES
95 SERIES
Socket and accessories for 40 series relays
A
95.05
Approvals
(according to type):
Certain relay/socket
combinations
095.01
060.48
Screw terminal (Box clamp) socket panel or 35mm rail mount 95.03 (blue) 95.03.0 (black) 95.05 (blue) 95.05.0 (black)
For relay type 40.31 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip
095.71
Plastic retaining and release clip
(supplied with socket - packaging code SPA)
095.01 095.01.0 095.01 095.01.0
8-way jumper link 095.18 095.18.0 095.18 095.18.0
Marker tag holder (for tags 060.48 type) 097.00
Identification tag 095.00.4
Modules (see table below) 99.02
Timer modules (see table below) 86.30
Sheet of marker tags for plastic retaining and release clip
095.01 and for marker tag holder 097.00, 48 tags, 6
x
12
mm,
for CEMBRE thermal transfer printers 060.48
Technical data
Rated values
10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV
Protection category IP 20
Ambient temperature °C –40…+70 (see diagram L95)
Screw torque Nm 0.5
Wire strip length mm 8
Max. wire size for 95.03 and 95.05 sockets solid wire stranded wire
mm21x6 / 2x2.5 1x4 / 2x2.5
AWG 1x10 / 2x14 1x12 / 2x14
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
L 95 - Total socket current v ambient temperature
A2 A1 COIL
11 COM
NO
NC
14
12
95.03
95.03 95.05
Total socket current (A)
E
U
R
O
P
E
A
N
E
U
R
O
P
E
A
N
PATENT
095.18
8-way jumper link for 95.03 and 95.05 sockets 095.18 (blue) 095.18.0 (black)
Rated values 10A - 250V
86.30
86 series timer modules
(12…24)VAC/DC; Bi-function: AI, DI; (0.05s…100h) 86.30.0.024.0000
(110…125)VAC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.120.0000
(230…240)VAC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.240.0000
Approvals (according to type):
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
99.02 coil indication and EMC suppression modules for 95.03 and 95.05 sockets
Diode (+A1, standard polarity) (6…220)VDC 99.02.3.000.00
LED (6…24)VDC/AC 99.02.0.024.59
LED (28…60)VDC/AC 99.02.0.060.59
LED (110…240)VDC/AC 99.02.0.230.59
LED + Diode (+A1, standard polarity) (6…24)VDC 99.02.9.024.99
LED + Diode (+A1, standard polarity) (28…60)VDC 99.02.9.060.99
LED + Diode (+A1, standard polarity) (110…220)VDC 99.02.9.220.99
LED + Varistor (6…24)VDC/AC 99.02.0.024.98
LED + Varistor (28…60)VDC/AC 99.02.0.060.98
LED + Varistor (110…240)VDC/AC 99.02.0.230.98
RC circuit (6…24)VDC/AC 99.02.0.024.09
RC circuit (28…60)VDC/AC 99.02.0.060.09
RC circuit (110…240)VDC/AC 99.02.0.230.09
Residual current by-pass (110…240)VAC 99.02.8.230.07
16
XI-2018, www.findernet.com
95 SERIES
Socket and accessories for 40 series relays
40
SERIES
A
95.55
Approvals
(according to type):
095.91.3
060.48
Screwless terminal socket panel or 35mm rail mount
95.55 (blue) 95.55.0 (black)
For relay type 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip 095.71
Plastic retaining and release clip
(supplied with socket - packaging code SPA) 095.91.3
Modules (see table below) 99.02
Timer modules (see table below) 86.30
Sheet of marker tags for plastic retaining and release clip
095.91.3
, 48 tags, 6
x
12
mm, for CEMBRE thermal transfer
printers 060.48
Technical data
Rated values
10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV
Protection category IP 20
Ambient temperature °C –25…+70 (see diagram L95)
Wire strip length mm 8
Max. wire size for 95.55 socket solid wire stranded wire
mm22x(0.5…1.5) 2x(0.5…1.5)
AWG 2x(21…18) 2x(21…18)
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
L 95 - Total socket current v ambient temperature
Total socket current (A)
86.30
86 series timer modules
(12…24)VAC/DC; Bi-function: AI, DI; (0.05s…100h) 86.30.0.024.0000
(110…125)VAC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.120.0000
(230…240)VAC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.240.0000
Approvals (according to type):
99.02
Approvals
(according to type):
DC Modules with
non-standard polarity
(+A2) on request.
99.02 coil indication and EMC suppression modules for 95.55 socket
Diode (+A1, standard polarity) (6…220)VDC 99.02.3.000.00
LED (6…24)VDC/AC 99.02.0.024.59
LED (28…60)VDC/AC 99.02.0.060.59
LED (110…240)VDC/AC 99.02.0.230.59
LED + Diode (+A1, standard polarity) (6…24)VDC 99.02.9.024.99
LED + Diode (+A1, standard polarity) (28…60)VDC 99.02.9.060.99
LED + Diode (+A1, standard polarity) (110…220)VDC 99.02.9.220.99
LED + Varistor (6…24)VDC/AC 99.02.0.024.98
LED + Varistor (28…60)VDC/AC 99.02.0.060.98
LED + Varistor (110…240)VDC/AC 99.02.0.230.98
RC circuit (6…24)VDC/AC 99.02.0.024.09
RC circuit (28…60)VDC/AC 99.02.0.060.09
RC circuit (110…240)VDC/AC 99.02.0.230.09
Residual current by-pass (110…240)VAC 99.02.8.230.07
17
XI-2018, www.findernet.com
40
SERIES
95 SERIES
Socket and accessories for 40 series relays
A
95.85.3
Approvals
(according to type):
095.91.3
060.48
Screw terminal (Box clamp) socket panel or 35mm rail mount 95.83.3 (blue) 95.83.30 (black) 95.85.3 (blue) 95.85.30 (black)
For relay type 40.31 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip 095.71
Plastic retaining and release clip
(supplied with socket - packaging code SPA)
095.91.3 095.91.30 095.91.3 095.91.30
8-way jumper link 095.08 095.08.0 095.08 095.08.0
Identification tag 095.00.4
Modules (see table below) 99.80
Marker tag holder 097.00
Sheet of marker tags for plastic retaining and release clip
095.91.3, 48 tags, 6
x
12
mm, for CEMBRE thermal transfert
printer 060.48
Technical data
Rated values
10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV 2kV
Protection category IP 20
Ambient temperature °C –40…+70 (see diagram L95)
Screw torque Nm 0.5
Wire strip length mm 7
Max. wire size for 95.83.3 and 95.85.3 sockets solid wire stranded wire
mm21x6 / 2x2.5 1x4 / 2x2.5
AWG 1x10 / 2x14 1x12 / 2x14
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
L 95 - Total socket current v ambient temperature
95.83.3 95.85.3
Total socket current (A)
E
U
R
O
P
E
A
N
E
U
R
O
P
E
A
N
PATENT
095.08
8-way jumper link for 95.83.3 and 95.85.3 sockets 095.08 (blue) 095.08.0 (black)
Rated values 10A - 250V
99.80
Approvals
(according to type):
* Modules in Black
housing are available
on request.
Green LED is standard.
Red LED available on
request.
99.80 coil indication and EMC suppression modules for 95.83.3 and 95.85.3 sockets
Blue*
Diode (+A1, standard polarity) (6…220)VDC 99.80.3.000.00
LED (6…24)VDC/AC 99.80.0.024.59
LED (28…60)VDC/AC 99.80.0.060.59
LED (110…240)VDC/AC 99.80.0.230.59
LED + Diode (+A1, standard polarity) (6…24)VDC 99.80.9.024.99
LED + Diode (+A1, standard polarity) (28…60)VDC 99.80.9.060.99
LED + Diode (+A1, standard polarity) (110…220)VDC 99.80.9.220.99
LED + Varistor (6…24)VDC/AC 99.80.0.024.98
LED + Varistor (28…60)VDC/AC 99.80.0.060.98
LED + Varistor (110…240)VDC/AC 99.80.0.230.98
RC circuit (6…24)VDC/AC 99.80.0.024.09
RC circuit (28…60)VDC/AC 99.80.0.060.09
RC circuit (110…240)VDC/AC 99.80.0.230.09
Residual current by-pass (110…240)VAC 99.80.8.230.07
18
XI-2018, www.findernet.com
95 SERIES
Socket and accessories for 40 series relays
40
SERIES
A
95.95.3
Approvals
(according to type):
095.91.3
060.48
Screw (Box clamp) terminal socket panel or 35mm rail mount
95.93.3 (blue) 95.93.30 (black) 95.95.3 (blue) 95.95.30 (black)
For relay type 40.31 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip
095.71
Plastic retaining and release clip
(supplied with socket - packaging code SPA) 095.91.3 095.91.30 095.91.3 095.91.30
8-way jumper link 095.08 095.08.0 095.08 095.08.0
Identification tag 095.00.4
Modules (see table below) 99.80
Sheet of marker tags for plastic retaining and release clip
095.91.3 and for marker tag holder 097.00
, 48 tags,
6x12mm, for CEMBRE thermal transfer printers 060.48
Technical data
Rated values
10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV
Protection category IP 20
Ambient temperature °C –40…+70 (see diagram L95)
Screw torque Nm 0.5
Wire strip length mm 8
Max. wire size for 95.93.3 and 95.95.3 sockets solid wire stranded wire
mm21x6 / 2x2.5 1x4 / 2x2.5
AWG 1x10 / 2x14 1x12 / 2x14
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
L 95 - Total socket current v ambient temperature
95.93.3 95.95.3
Total socket current (A)
E
U
R
O
P
E
A
N
E
U
R
O
P
E
A
N
PATENT
095.08
8-way jumper link for 95.93.3 and 95.95.3 sockets 095.08 (blue) 095.08.0 (black)
Rated values 10A - 250V
99.80
Approvals
(according to type):
* Modules in Black
housing are available
on request.
Green LED is standard.
Red LED available on
request.
99.80 coil indication and EMC suppression modules for 95.93.3 and 95.95.3 sockets
Blue*
Diode (+A1, standard polarity) (6…220)VDC 99.80.3.000.00
LED (6…24)VDC/AC 99.80.0.024.59
LED (28…60)VDC/AC 99.80.0.060.59
LED (110…240)VDC/AC 99.80.0.230.59
LED + Diode (+A1, standard polarity) (6…24)VDC 99.80.9.024.99
LED + Diode (+A1, standard polarity) (28…60)VDC 99.80.9.060.99
LED + Diode (+A1, standard polarity) (110…220)VDC 99.80.9.220.99
LED + Varistor (6…24)VDC/AC 99.80.0.024.98
LED + Varistor (28…60)VDC/AC 99.80.0.060.98
LED + Varistor (110…240)VDC/AC 99.80.0.230.98
RC circuit (6…24)VDC/AC 99.80.0.024.09
RC circuit (28…60)VDC/AC 99.80.0.060.09
RC circuit (110…240)VDC/AC 99.80.0.230.09
Residual current by-pass (110…240)VAC 99.80.8.230.07
19
XI-2018, www.findernet.com
40
SERIES
95 SERIES
Socket and accessories for 40 series relays
A
95.63
Approvals
(according to type):
95.65
Approvals
(according to type):
Screw terminal (Box clamp) socket panel or 35mm rail mount 95.63 95.65
For relay type 40.31 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip 095.71
8-way jumper link 095.08 095.08
Modules (see table below) 99.01 —
Technical data
Rated values 10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV 2kV
Protection category IP 20
Ambient temperature °C –40…+70 (see diagram L95)
Screw torque Nm 0.5
Wire strip length mm 7
Max. wire size for 95.63 and 95.65 sockets solid wire stranded wire
mm21x6 / 2x2.5 1x4 / 2x2.5
AWG 1x10 / 2x14 1x12 / 2x14
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
L 95 - Total socket current v ambient temperature
E
U
R
O
P
E
A
N
E
U
R
O
P
E
A
N
PATENT
095.08
8-way jumper link for 95.63 and 95.65 sockets 095.08 (blue)
Rated values 10A - 250V
99.01
Approvals
(according to type):
* Modules in Black
housing are available
on request.
Green LED is standard.
Red LED available on
request.
99.01 coil indication and EMC suppression modules for type 95.63 socket
Blue*
Diode (+A1, standard polarity) (6…220)VDC 99.01.3.000.00
Diode (+A2, non-standard polarity) (6…220)VDC 99.01.2.000.00
LED (6…24)VDC/AC 99.01.0.024.59
LED (28…60)VDC/AC 99.01.0.060.59
LED (110…240)VDC/AC 99.01.0.230.59
LED + Diode (+A1, standard polarity) (6…24)VDC 99.01.9.024.99
LED + Diode (+A1, standard polarity) (28…60)VDC 99.01.9.060.99
LED + Diode (+A1, standard polarity) (110…220)VDC 99.01.9.220.99
LED + Diode (+A2, non-standard polarity) (6…24)VDC 99.01.9.024.79
LED + Diode (+A2, non-standard polarity) (28…60)VDC 99.01.9.060.79
LED + Diode (+A2, non-standard polarity) (110…220)VDC 99.01.9.220.79
LED + Varistor (6…24)VDC/AC 99.01.0.024.98
LED + Varistor (28…60)VDC/AC 99.01.0.060.98
LED + Varistor (110…240)VDC/AC 99.01.0.230.98
RC circuit (6…24)VDC/AC 99.01.0.024.09
RC circuit (28…60)VDC/AC 99.01.0.060.09
RC circuit (110…240)VDC/AC 99.01.0.230.09
Residual current by-pass (110…240)VAC 99.01.8.230.07
95.63 95.65
Total socket current (A)
20
XI-2018, www.findernet.com
95 SERIES
Socket and accessories for 40 series relays
40
SERIES
A
95.13.2
95.15.2
Approvals
(according to type):
PCB socket 95.13.2 (blue) 95.13.20 (black) 95.15.2 (blue) 95.15.20 (black)
For relay type 40.31 40.51, 40.52, 40.61, 40.62
Accessories
Metal retaining clip (supplied with socket -
packaging code SMA)
095.51
Plastic retaining clip 095.52
Technical data
Rated values 12A - 250V 10A - 250V*
Dielectric strength between coil and contacts (1.2/50 μs) 6kV
Protection category IP 20
Ambient temperature °C –40…+70
* For currents >10A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12).
With the relay 40.51 the change-over contact will be 21-12-14.
40.61
95.13. 2
20
30
3. 5
13
7.5
3. 51. 5
12 14
11
A1
A2
22 24
21
29
20
3
5
12.4
1.5
7.5
=
=
5
6
12
11
14
A1 A2
22
21
24
40.51
40.52
40.31
95.13.2 95.15.2
Copper side view
Copper side view
Packaging codes
How to code and identify retaining clip and packaging options for sockets.
Example:
9 5 . P 5 S P A
A Standard packaging
SM Metal retaining clip
SP Plastic retaining clip
Please see general technical information 21
XI-2018, www.findernet.com
40
SERIES
95 SERIES
Socket and accessories for 40 series relays