KP1830 www.vishay.com Vishay Roederstein AC and Pulse Film Foil Capacitors KP Radial Potted Type FEATURES L max. W max. Marking * 5 mm lead pitch * Supplied loose in box taped in ammopack or reel H max. 0.5 6.0 -1 pcm 5.0 0.4 O 0.5 0.4 * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 ENCAPSULATION Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0 Dimensions in millimeters CLIMATIC TESTING CLASS ACCORDING TO IEC 60068-1 MAIN APPLICATIONS 55/100/56 Oscillator, timing and LC/RC filter circuits, high frequency coupling of fast digital and analog IC's. CAPACITANCE RANGE REFERENCE STANDARDS IEC 60384-13 MARKING C-value; tolerance; rated voltage; sub-class; manufacturer's type; code for dielectric material; manufacturer's location; manufacturer's logo; year and week DIELECTRIC Polypropylene film ELECTRODES Tin foil 100 pF to 0.022 F CAPACITANCE TOLERANCE 10 % , 5 %, 2.5 %, 2 %, 1 % LEADS Tinned wire MAXIMUM APPLICATION TEMPERATURE 100 C DETAIL SPECIFICATION For more detailed data and test requirements contact: dc-film@vishay.com CONSTRUCTION Mono construction RATED DC VOLTAGES 63 V, 250 V, 630 V RATED AC VOLTAGES 40 V, 160 V, 250 V Revision: 03-Feb-17 Document Number: 26016 1 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com Vishay Roederstein COMPOSITION OF CATALOG NUMBER CAPACITANCE (numerically) MULTIPLIER (nF) 0.01 1 0.1 2 1 3 KP 1830 2 TYPE CONSTRUCTION Example: 10 110 0.1 nF 100 pF 210 1.0 nF 1.0 nF 310 10 nF 10 nF 63 4 G VOLTAGE CODE PACKAGING CODE 06 = 63 Vdc Bulk 25 = 250 Vdc TOLERANCE CODE 63 = 630 Vdc 1 1% 2 2% 3 2.5 % 4 5% 5 10 % G Ammo (H = 18.5) W Reel (H = 18.5) SPECIFIC REFERENCE DATA DESCRIPTION Tangent of loss angle: VALUE at 1 kHz at 10 kHz at 100 kHz at 1 MHz - 10 x 10-4 C 1000 pF - 5x 1000 pF < C 5000 pF - 5 x 10-4 10 x 10-4 - 5000 pF < C 20 000 pF - 10 x 10-4 15 x 10-4 - - 10-4 10-4 - 20 000 pF < C < 33 000 pF 10-4 15 x Pitch (mm) Maximum pulse rise time (dU/dt)R [V/s] 5 > 10 000 25 x R between leads, for C 0.33 F at 100V, 1min > 500 000M R between leads and case, 100V, 1min > 30 000M Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum application temperature Revision: 03-Feb-17 1.6 x URDC, 1 min 2 x URDC, 1 min 100 C Document Number: 26016 2 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com CAPACITANCE CAPACITANCE CODE 100 pF 110 pF 120 pF 130 pF 150 pF 160 pF 180 pF 200 pF 220 pF 240 pF 270 pF 300 pF 330 pF 360 pF 390 pF 430 pF 470 pF 510 pF 560 pF 620 pF 680 pF 750 pF 820 pF 910 pF 1000 pF 1100 pF 1200 pF 1300 pF 1500 pF 1600 pF 1800 pF 2000 pF 2200 pF 2400 pF 2700 pF 3000 pF 3300 pF 3600 pF 3900 pF 4300 pF 4700 pF 5100 pF 5600 pF 6200 pF 6800 pF 7500 pF 8200 pF 9100 pF 0.010 F 0.011 F 0.012 F 0.013 F 0.015 F 0.016 F 0.018 F 0.020 F 0.022 F -110 -111 -112 -113 -115 -116 -118 -120 -122 -124 -127 -130 -133 -136 -139 -143 -147 -151 -156 -162 -168 -175 -182 -191 -210 -211 -212 -213 -215 -216 -218 -220 -222 -224 -227 -230 -233 -236 -239 -243 -247 -251 -256 -262 -268 -275 -282 -291 -310 -311 -312 -313 -315 -316 -318 -320 -322 Vishay Roederstein VOLTAGE CODE 06 63 VDC / 40 VAC W (mm) 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 9.0 9.0 9.0 7.5 H (mm) 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 10.0 10.0 10.0 9.0 L (mm) 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 VOLTAGE CODE 25 250 VDC / 160 VAC W (mm) 4.5 4.5 4.5 4.5 5.5 5.5 5.5 5.5 5.5 5.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 9.0 9.0 9.0 9.0 - H (mm) 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 10.0 10.0 10.0 10.0 - L (mm) 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 - VOLTAGE CODE 63 630 VDC / 250 VAC W (mm) 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.5 5.5 5.5 5.5 5.5 5.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 9.0 9.0 9.0 9.0 - H (mm) 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 10.0 10.0 10.0 10.0 - L (mm) 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 - Note * Further C-values upon request Revision: 03-Feb-17 Document Number: 26016 3 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com Vishay Roederstein RECOMMENDED PACKAGING LETTER CODE TYPE OF PACKAGING HEIGHT (H) (mm) REEL DIAMETER (mm) ORDERING CODE EXAMPLE PITCH 5 G Ammo 18.5 S (1) W Reel KP1830-310-065-G X 18.5 350 KP1830-310-065-W - Bulk X - - KP1830-310-065 X Note (1) S = box size 55 mm x 210 mm x 340 mm (W x H x L) EXAMPLE OF ORDERING CODE TYPE CAPACITANCE CODE VOLTAGE CODE TOLERANCE CODE PACKAGING CODE KP1830 210 63 1 G Tolerance codes: 1 = 1 % (F); 2 = 2 % (G); 3 = 2.5 % (H); 4 = 5 % (J); 5 = 10 % (K) Note * For detailed tape specifications refer to "Packaging Information" www.vishay.com/doc?28139 or end of catalog MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting on printed-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to "Packaging information" www.vishay.com/doc?28139 or end of catalog Specific Method of Mounting of Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board. * For pitches 15 mm the capacitors shall be mechanically fixed by the leads * For larger pitches the capacitors shall be mounted in the same way and the body clamped Space Requirements on Printed-Circuit Board The maximum length and width of film capacitors is shown in the drawing: * Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned * Product height with seating plane as given by "IEC 60717" as reference: hmax. h + 0.4 mm or hmax. h' + 0.4 mm bmax. = b + 0.3 mm Eccentricity Imax. = I + 0.3 mm Storage Temperature Tstg = -25 C to +35 C with RH maximum 75 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient free temperature of 23 C 1 C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % 2 %. For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. Revision: 03-Feb-17 Document Number: 26016 4 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com Vishay Roederstein 4 Z () C/C (%) CHARACTERISTICS 3 10 2 1 1 0 -5 -6 100 pF 0.01 -60 -40 -20 0 40 20 60 80 1 100 120 Tamb (C) 1.2 100 10 f (MHz) Impedance versus frequency Z = f (f) (lead length 2.0 mm) 1000 Impedance as a function of frequency (typical curve) Capacitance as a function of ambient temperature (typical curve) 102 AC Voltage (V) factor 220 pF 0.033 F -4 680 pF 0.1 -3 2200 pF -2 0.001 F 4700 pF -1 1.0 0.8 0.6 0 pF 330 0 pF 680 5 F 0.01 0.4 0.2 0.0 -60 -20 20 100 Tamb (C) 60 Tamb 100 C, 63 VDC 101 102 103 103 103 AC Voltage (V) AC Voltage (V) 102 102 105 f (Hz) Maximum RMS voltage as a function of frequency Revision: 03-Feb-17 f (Hz) F 0p 10 0 pF 22 0 pF F 4 7 00 p 10 pF 00 F 22 00 p F 47 01 0. 104 105 Maximum RMS voltage as a function of frequency Maximum DC and AC voltage as a function of temperature Tamb 100 C, 250 VDC 101 102 103 104 106 Tamb 100 C, 630 VDC 101 102 103 104 105 106 f (Hz) 107 Maximum RMS voltage as a function of frequency Document Number: 26016 5 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com Vishay Roederstein HEAT CONDUCTIVITY (G) AS A FUNCTION OF ORIGINAL PITCH AND CAPACITOR BODY THICKNESS IN mW/C Wmax. (mm) HEAT CONDUCTIVITY (mW/C) PITCH 5 mm 4.5 3 5.5 4 7.5 6 9.0 7 POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of the free air ambient temperature. The power dissipation can be calculated according type detail specification "HQN-384-01/101: Technical Information Film Capacitors" with the typical tgd of the curves. The component temperature rise (T) can be measured (see section "Measuring the component temperature" for more details) or calculated by T = P/G: * T = component temperature rise (C) * P = power dissipation of the component (mW) * G = heat conductivity of the component (mW/C) MEASURING THE COMPONENT TEMPERATURE A thermocouple must be attached to the capacitor body as in: Thermocouple The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC). The temperature rise is given by T = TC - Tamb. To avoid radiation or convection, the capacitor should be tested in a wind-free box. APPLICATION NOTE AND LIMITING CONDITIONS To select the capacitor for a certain application, the following conditions must be checked: 1. The peak voltage (Up) shall not be greater than the rated DC voltage (URDC). 2. The peak-to-peak voltage (Up-p) shall not be greater than the maximum (Up-p) to avoid the ionization inception level. 3. The maximum component surface temperature rise must be lower than the limits. 4. The maximum application temperature must be lower than 105 C. 5. There is no limit for the voltage pulse slope in the application. Revision: 03-Feb-17 Document Number: 26016 6 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com Vishay Roederstein INSPECTION REQUIREMENTS General Notes Sub-clause numbers of tests and performance requirements refer to the "Sectional Specification, Publication IEC 60384-13 and Specific Reference Data". Group C Inspection Requirements SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapters "General Data" of this specification 4.3.1 Initial measurements Capacitance at 1 kHz Tangent of loss angle at 100 kHz 4.3 Robustness of terminations Tensile: load 10 N; 10 s Bending: load 5 N; 4 x 90 4.4 Resistance to soldering heat No predrying Method: 1A Solder bath: 280 C 5 C Duration: 5 s No visible damage 4.14 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5.0 min 0.5 min Recovery time: min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 2 % of the value measured in 4.3.1 SUB-GROUP C1B PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance at 1 kHz Tangent of loss angle at 100 kHz 4.14 Solvent resistance of the marking Isopropylalcohol at room temperature Method: 1 Rubbing material: cotton wool Immersion time: 5.0 min 0.5 min 4.6 Rapid change of temperature A = -55 C B = +105 C 5 cycles Duration t = 30 min 4.7 Vibration Visual examination Mounting: See section "Mounting" of this specification Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s2 (whichever is less severe) Total duration 6 h No visible damage Visual examination No visible damage Capacitance |C/C| 2 % of the value measured in 4.6.1 Tangent of loss angle As specified in section "Tangent of loss angle" of this specification 4.7.2 Final inspection Revision: 03-Feb-17 No visible damage Legible marking Document Number: 26016 7 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com Vishay Roederstein SUB-CLAUSE NUMBER AND TEST CONDITIONS 4.9 Shock Mounting: See section "Mounting" of this specification Pulse shape: half sine Acceleration: 490 m/s2 Duration of pulse: 11 ms PERFORMANCE REQUIREMENTS 4.9.3 Final measurements Visual examination No visible damage Capacitance |C/C| 2 % of the value measured in 4.6.1. SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.10 Climatic sequence 4.10.2 Dry heat 4.10.3 Damp heat cyclic Test Db, first cycle 4.10.4 Cold Temperature: -55 C Duration: 2 h 4.10.6 Damp heat cyclic Test Db, remaining cycles Recovery 1 h to 2 h 4.10.6.2 Final measurements Temperature: +100 C Duration: 16 h Voltage proof = URDC for 1 min within 15 min after removal from testchamber No breakdown or flash-over Visual examination No visible damage Legible marking Capacitance |C/C| 2 % of the value measured in 4.10.2 Tangent of loss angle As specified in section "Tangent of loss angle" of this specification or 1.4 times the value measured in 4.3.1 whichever is greater Insulation resistance 50 % of values specified in section "Insulation resistance" of this specification SUB-GROUP C2 4.11 Damp heat steady state 4.11.1 Initial measurements 4.11.3 Final measurements Revision: 03-Feb-17 Capacitance at 1 kHz Tangent of loss angle at 1 kHz Voltage proof = URDC for 1 min within 15 min after removal from testchamber No breakdown or flash-over Visual examination No visible damage Legible marking Capacitance |C/C| 1 % of the value measured in 4.11.1. Tangent of loss angle As specified in section "Tangent of loss angle" of this specification or 1.4 times the value measured in 4.11.1 whichever is greater Insulation resistance 50 % of values specified in section "Insulation resistance" of this specification Document Number: 26016 8 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 KP1830 www.vishay.com SUB-CLAUSE NUMBER AND TEST Vishay Roederstein CONDITIONS PERFORMANCE REQUIREMENTS SUB GROUP C3 4.12 Endurance Duration: 2000 h 1.5 x URDC at 85 C 1.05 x URDC at 100 C 4.12.1 Initial measurements Capacitance at 1 kHz Tangent of loss angle at 100 kHz 4.12.5 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 2 % of the value measured in 4.12.1 Tangent of loss angle As specified in section "Tangent of loss angle" of this specification or 1.4 times the value measured in 4.12.1 whichever is greater Insulation resistance As specified in section "Insulation resistance" of this specification Revision: 03-Feb-17 Document Number: 26016 9 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2021 1 Document Number: 91000