Dupline(R) Field- and Installationbus Receiver with Analog Current Output Types FAD 1530, FAD 1531, FAD 1532 * Receivers with current signal output * Current output signals: FAD 1530: 1 x 0 to 1 mA FAD 1531: 1 x 0 to 20 mA FAD 1532: 1 x 4 to 20 mA * 8-bit (8 channels) resolution * For binary transmitted analogue signals * Galvanically separated output * D-housing * Plug-in type module * AC power supply Product Description Ordering Key Dupline analog receivers with standard current output signals (0 to 1 mA, 0 to 20 mA, 4 to 20 mA). Convert binary codes into analog current signals. Type: Dupline Output signal Supply Supply Ordering no. 0 to 1 mA Ordering no. 0 to 20 mA Ordering no. 4 to 20 mA 24 VAC 120 VAC 220 VAC FAD 1530 024 FAD 1530 120 FAD 1530 220 FAD 1531 024 FAD 1531 120 FAD 1531 220 FAD 1532 024 FAD 1532 120 FAD 1532 220 Code module FMK A to FMK P FMK A to FMK P FMK A to FMK P FAD 1530 024 Type Selection Output Specifications Output Signal range Isolated in groups of Output load resistance Resolution Settling time Short-circuit protection Short-circuit current Open loop voltage Inaccuracy Cable length Dielectric voltage Output - Dupline FAD 1530 ... FAD 1531 ... FAD 1532 ... 1 current output 0 to 1 mA 1x1 10 k 8 bits (3.92 A/LSB) 1 pulse train + 10 ms Yes 1 mA Approx. 15 V 1% of full scale 3m 1 current output 0 to 20 mA 1x1 350 8 bits (78.43 A/LSB) 1 pulse train + 10 ms Yes 20 mA Approx. 15 V 1% of full scale 3m 1 current output 4 to 20 mA 1x1 350 8 bits (62.75 A/LSB) 1 pulse train + 10 ms Yes 20 mA Approx. 15 V 1% of full scale 3m 200 VAC (rms) 200 VAC (rms) 200 VAC (rms) Specifications are subject to change without notice (01.09.99) 1 FAD 1530, FAD 1531, FAD 1532 Supply Specifications General Specifications Power supply Rated operational voltage through pins A1 & A2 220 Output OFF delay upon loss of Dupline carrier Power ON delay Environment Degree of protection Pollution degree Operating temperature Storage temperature Humidity (non-condensing) Mechanical resistance Shock Vibration Dimensions Material (see "Technical Information") Weight Approvals 120 024 Frequency Voltage interruption Rated operational power Rated impulse 220 withstand voltage 120 024 Dielectric voltage Supply - Dupline Supply - Output Overvoltage cat. III (IEC 60664) 230 VAC +6%, -15% (IEC 60038) 120 VAC 10% (IEC 60038) 24 VAC 10% 45 to 65 Hz 40 ms Typ. 2.5 VA 4 kV 2.5 kV 800 V 2 kVAC (rms) 2 kVAC (rms) Mode of Operation Receiver with current signal output. The binary status of an entire channel group (8 bit) is converted to a current signal. The binary status of the selected group may be generated by Dupline transmitters with analog inputs (current, voltage, temperature etc.) or by PC's. The least significant bit (influencing the output current by 0.392% of full scale) is the highest channel of the select- Undefined Undefined, 1 s IP 20 3 (IEC 60664) -20 to +50C (-4 to +122F) -50 to +85C (-58 to +185F) 20 to 80% 15 G (11 ms) 2 G (6 to 55 Hz) D-housing 200 g CSA, UL Operation Diagram ed group (C8 if FMK C is plugged in). The most significant bit (influencing the output current by 49.8% of full scale) is the lowest channel of the selected group (C1 in the above example). Output signal MSB = Most Significant Bit LSB = Least Significant Bit Note: Analog receivers must not be used in systems where channel generators with 2 or 3 sequences are installed. Channel status Wiring Diagram Accessories Socket Socket cover Hold down spring Front mounting bezel DIN-rail for D 411 D 411 BB 5 HF FRS 2 FMD 411 For further information refer to "Accessories". Load S: signal wire. 2 Power Supply Specifications are subject to change without notice (01.09.99)