Specifications are subject to change without notice (01.09.99) 1
Dupline®Field- and Installationbus
Type: Dupline
Output signal
Supply
Ordering Key
Receivers with current signal output
Current output signals:
FAD 1530: 1 x 0 to 1 mA
FAD 1531: 1 x 0 to 20 mA
FAD 1532: 1 x 4 to 20 mA
8-bit (8 channels) resolution
For binary transmitted analogue signals
Galvanically separated output
D-housing
Plug-in type module
AC power supply
Product Description
Dupline analog receivers with
standard current output sig-
nals (0 to 1 mA, 0 to 20 mA, 4
to 20 mA). Convert binary
codes into analog current sig-
nals.
Type Selection
Supply Ordering no. Ordering no. Ordering no.
0 to 1 mA 0 to 20 mA 4 to 20 mA
24 VAC FAD 1530 024 FAD 1531 024 FAD 1532 024
120 VAC FAD 1530 120 FAD 1531 120 FAD 1532 120
220 VAC FAD 1530 220 FAD 1531 220 FAD 1532 220
Code module FMK A to FMK P FMK A to FMK P FMK A to FMK P
Output Specifications
FAD 1530 ... FAD 1531 ... FAD 1532 ...
Output 1 current output 1 current output 1 current output
Signal range 0 to 1 mA 0 to 20 mA 4 to 20 mA
Isolated in groups of 1 x 1 1 x 1 1 x 1
Output load resistance 10 kΩ≤350 Ω≤350
Resolution 8 bits (3.92 µA/LSB) 8 bits (78.43 µA/LSB) 8 bits (62.75 µA/LSB)
Settling time 1 pulse train + 10 ms 1 pulse train + 10 ms 1 pulse train + 10 ms
Short-circuit protection Yes Yes Yes
Short-circuit current 1 mA 20 mA 20 mA
Open loop voltage Approx. 15 V Approx. 15 V Approx. 15 V
Inaccuracy 1% of full scale 1% of full scale 1% of full scale
Cable length 3 m 3 m 3 m
Dielectric voltage
Output - Dupline 200 VAC (rms) 200 VAC (rms) 200 VAC (rms)
Receiver with Analog Current Output
Types FAD 1530, FAD 1531, FAD 1532
FAD 1530 024
2Specifications are subject to change without notice (01.09.99)
Supply Specifications
FAD 1530, FAD 1531, FAD 1532
General Specifications
Power supply Overvoltage cat. III (IEC 60664)
Rated operational voltage
through pins A1 & A2 220 230 VAC +6%,
-15% (IEC 60038)
120 120 VAC ± 10% (IEC 60038)
024 24 VAC ± 10%
Frequency 45 to 65 Hz
Voltage interruption 40 ms
Rated operational power Typ. 2.5 VA
Rated impulse 220 4 kV
withstand voltage 120 2.5 kV
024 800 V
Dielectric voltage
Supply - Dupline 2 kVAC (rms)
Supply - Output 2 kVAC (rms)
Output OFF delay
upon loss of Dupline carrier Undefined
Power ON delay Undefined, 1 s
Environment
Degree of protection IP 20
Pollution degree 3 (IEC 60664)
Operating temperature -20° to +50°C (-4° to +122°F)
Storage temperature -50° to +85°C (-58° to +185°F)
Humidity (non-condensing) 20 to 80%
Mechanical resistance
Shock 15 G (11 ms)
Vibration 2 G (6 to 55 Hz)
Dimensions
Material
(see "Technical Information") D-housing
Weight 200 g
Approvals CSA, UL
Operation DiagramMode of Operation
Receiver with current signal
output. The binary status of
an entire channel group (8 bit)
is converted to a current sig-
nal. The binary status of the
selected group may be gen-
erated by Dupline transmit-
ters with analog inputs (cur-
rent, voltage, temperature
etc.) or by PC’s.
The least significant bit (influ-
encing the output current by
0.392% of full scale) is the
highest channel of the select-
ed group (C8 if FMK C is
plugged in). The most signifi-
cant bit (influencing the output
current by 49.8% of full scale)
is the lowest channel of the
selected group (C1 in the
above example).
Note: Analog receivers must
not be used in systems where
channel generators with 2 or 3
sequences are installed.
Output
signal
Accessories
SocketD 411
Socket cover BB 5
Hold down springHF
Front mounting bezel FRS 2
DIN-rail for D 411 FMD 411
For further information refer to "Accessories".
Wiring Diagram
Load
S: signal wire.
MSB =
Most Significant Bit
LSB =
Least Significant Bit
Channel status
Power
Supply