G34960007700 - Carlo Gavazzi Group

Du line

Fieldbus Installationbus

Specifications are subject to change without notice (05.05.03) 1

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Type: Dupline®

H4-Housing

Combined module

Interface type

DC supply

• Schneider (Telemecanique & Modicon) Slave

• Plug and play: Automatic communication with specific

PLC/Controllers

• Built-in normal Dupline®Channel Generator

• 128 I/O’s and DC power supply on 3 wires

• RS485 port for interfacing to control system

• Split-I/O mode selectable (128 inputs and 128 outputs)

• LED-indications for supply, Dupline®carrier and Com-

port TX

• Galvaniccally isolated Com-port supplied by internal

DC/DC converter

Product Description Ordering Key

G 3495 0007 is designed as a

cost-effective solution for

interfacing Dupline®I/O’s to

all Schneider PLCs – the

Telemecanique and Modicon

families. It performs three

functions: Dupline®channel

generator, power supply syn-

chronization (enables 3-wire

system with supply) and

RS485 interface.

Type Selection

Supply PLC Interface Conformance Ordering no.

20-30 VDC Schneider, Telemecanique and Modicon. G 3496 0007 700

G 3496 0007 700

Input/Output Specifications

Dupline®Plug & Play Master Module

Interface for Schneider (Telemecanique & Modicon) PLC

Power Output

Output voltage 20-30 VDC (pulsating)

Output current < 3.0 A @ 50°C

Short circuit protection 4 A quick acting fuse

Output voltage drop < 1.0 V

Dupline®carrier

Output voltage 8.2 V (pulsating)

Current < 60 mA

Short circuit protection Yes

Scan time

128 channels 132.2 ms

64 channels 69.8 ms

Communication Port

Standard RS485

Connection 9 pole female Sub-D

Dielectric voltage

Com-port-Dupline®1 kVAC (rms)

Protocol Unitelway V2

Channel Configuration in PLC

Baud rate 9600

Data bits 8

Start bit -

Stop bit 1

Parity Odd

Flow-control None

Pin assignment

RS485

GND 5

Type G 3496 0007

Supply Specifications

Power supply

Overvoltage cat. III (IEC 60664)

Operational voltage (Vin) 20-30 VDC

Reverse polarity protection None

Current consumption < 150 mA + Power load

Power dissipation < 5 W

Transient protection voltage 800 V

Dielectric voltage

Supply – Dupline® None

Supply – Com-port 1 kVAC (rms)

Power ON delay 2 s

Indication for

Com-port TX LED, red

Supply ON LED, green

Dupline®carrier LED, yellow

Environment

Pollution degree 2 (IEC 60664)

Operating temperature

0° to +50°C (+32° to +122°F)

Storage temperature

-50° to +85°C (-58° to +185°F)

Humidity (non-condensing) 20 to 80%

Mechanical resistance

Shock 15 G (11 ms)

Vibration 2 G (6 to 55 Hz)

Dimensions H4-Housing

Material (See Technical Information)

Weight 100 g

General Specifications

Du line

Fieldbus Installationbus

2Specifications are subject to change without notice (30.11.00)

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Mode of Operation

The Dupline

Master Module

(DMM) controls a 3-wire bus

with signal, DC-power and

common GND. The DMM is

connected to a standard DC-

supply, which it synchronizes

with the Dupline

carrier signal

before it is output to supply.

The synchronization is neces-

sary in order to enable the

Dupline

and DC-supply to

share the GND-wire.

The Dupline

Master Module is

a Dupline

Channel Generator

with the function of a master.

This means that the 128

Dupline

I/0’s will be read/writ-

ten by the DMM and then

sentto the PLC.

The DMM can run in two dif-

ferent modes – Normal mode

and split I/O mode. In Normal

mode, Dupline

operates as a

peer-to-peer system, where

the channel generator auto-

matically establishes a con-

nection between Dupline

inputs and Dupline

outputs

which are coded to the same

Dupline

address. If e.g. an

input coded for B5 is activat-

ed, the output(s) coded for B5

will also be activated.

Consequently, a Dupline

-out-

put can either be activated

through the output-data

received on DMM or by an

active Dupline

input coded

for the same Dupline

address. In "Split I/O" mode,

the channel generator treats

the Dupline

inputs and

Dupline

outputs indepen-

dently. If e.g. an input coded

for B5 is activated, the DMM

will make the information avail-

able for the PLC (like in normal

mode), but it will not automati-

cally activate the Dupline out-

put(s) coded to B5. The

Dupline

outputs are con-

trolled exclusively through the

output data received from the

PLC. In this mode, up to 128

Dupline

inputs and 128

Dupline

outputs are available,

since an input and an output

coded to the same Dupline

address can operate indepen-

dently.

G 3496 0007

Dip-Switch Setting

Sw.3 On: Communication on Datalink address 4 and 5

Off: Communication on Datalink address 6 and 7

Sw.4 On: Split I/O Channel Generator Mode

Off: Normal Dupline

Monostable Channel

Generator Mode

Sw.5 On: 64 Dupline

channels

Off: 128 Dupline

channels

Sw.6 On: Maintain data to Dupline

receivers in case of

communication failure

Off: Clear data to Dupline

receivers in case of

communication failure after 75 Dupline

scans

Memory Mapping

Dupline

Schneider, Teleme- Dupline

Schneider, Teleme-

Channel canique & Modicon Channel canique & Modicon

Read Write Read Write

A1 MW0: X0 MW8: X0 E1 MW2: X0 MW10: X0

A2 MW0: X1 MW8: X1 F1 MW2: X8 MW10: X8

A3 MW0: X2 MW8: X2 G1 MW3: X0 MW11: X0

A4 MW0: X3 MW8: X3 H1 MW3: X8 MW11: X8

A5 MW0: X4 MW8: X4 I1 MW4: X0 MW12: X0

A6 MW0: X5 MW8: X5 J1 MW4: X8 MW12: X8

A7 MW0: X6 MW8: X6 K1 MW5: X0 MW13: X0

A8 MW0: X7 MW8: X7 L1 MW5: X8 MW13: X8

B1 MW0: X8 MW8: X8 M1 MW6: X0 MW14: X0

B8 MW0: X15 MW8: X15 N1 MW6: X8 MW14: X8

C1 MW1: X0 MW9: X0 O1 MW7: X0 MW15: X0

D1 MW1: X8 MW9: X8 P1 MW7: X8 MW15: X8

Table of the memory mapping to the PLC

Du line

Fieldbus Installationbus

Specifications are subject to change without notice (30.11.00) 3

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Installation Hints

Slow-flashing TX-LED

Hardware fault Check the wiring.

No Dupline

Carrier-LED

Dupline

short circuit Short circuit between the

two Dupline

wires.

Accessories

Cable Sub-D 9M/8 mini Din RS-232-SC1

Additional Information

Scope of supply

1 x Master Module G3496 0007 700

Pin Assignment

9-pin D-shell

8-pin Mini Din

6 7 8

1 2

G 3496 0007

DMM G34960007 Schneider (Telemecanique & Modicon)

9P D-SUB Male 8-pin mini-DIN Male (TER or AUX)

8 (A) 2 (DA)

3 (B) 1 (DB)

5 (GND) 7 (GND)