Part Number 405EX
Revision 1.23 - January 28, 2009
AMCC Proprietary 1
405EX
PowerPC 405EX Embedded Processor
Data Sheet
Features
• AMCC PowerPC® 405 32-bit RISC processor
core operating from 333MHz to 600MHz including
16KB I- and D-caches with parity checking
• 128-bit processor local bus (PLB) operating up to
200MHz
• 32-bit peripheral bus (OPB) operating up to
100 MHz
• External 8-,16-, or 32-bit peripheral bus (EBC)
operating up to 100MHz
• External bus master (EBM) operating up to
100MHz
• Optional Security feature with True Random
Number generation
• Eight- and 16-bit NAND Flash interface
• Boot from NOR Flash on the external peripheral
bus or NAND Flash on the NAND Flash interface
• DMA (4-channel) support for all on-chip slaves
and external bus, UARTs, and devices on the EBC
• DDR1/2 SDRAM interface operating up to 400
Mbps
• Two one-lane PCI Express interfaces operating up
to 2.5 Gbps
• Two Gigabit Ethernet interfaces (half- and full-
duplex) to external PHY (GMII/RGMII)
• USB 2.0 OTG port configurable as either Host or
Device
• Programmable universal interrupt controller (UIC)
• General Purpose Timer (GPT)
• Up to two serial ports (16750 compatible UART)
• Two IIC interfaces operating up to 400kHz and
supporting all standard IIC EEPROMs
• One SCP (SPI) synchronous full-duplex channel
operating up to 25MHz
• General purpose I/Os (GPIOs), each with
programmable interrupts and outputs
• Supports JTAG for board-level testing
• System power management, low power
dissipation and small form factor
• Available in a RoHS compliant (lead-free) package
Description
With speeds up to 600MHz, a flexible off-chip memory
architecture, and a diverse communications package
that includes PCI Express, USB 2.0 OTG, and
10/100/1000 Ethernet, the PowerPC 405EX
embedded processor provides a low power and small
footprint system-on-a-chip (SOC) solution for a wide
range of high performance, cost-constrained
embedded applications. This includes wireless LAN
applications, security appliances, internet appliances,
line cards, and intelligent USB peripherals. It is an
easily programmable general purpose, 32-bit RISC
controller that offers an upgrade path for applications
in need of performance and connectivity
improvements.
Technology: Cu-08 CMOS, 90nm
Package: 388-ball, 27mm × 27mm, enhanced plastic
ball grid array (EPBGA), 1mm ball pitch
Power consumption: typically less than 1.8W at
400MHz
Voltages required: 3.3V, 2.5V, 1.8V (DDR2 SDRAM
only), and 1.2V
PPC405EX – PowerPC 405EX Embedded Processor
2 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table of Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ordering, PVR, and JTAG Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Address Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PowerPC 405 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Internal Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
External Bus Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
NAND Flash Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DMA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
USB 2.0 OTG Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DDR1/2 SDRAM Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Security Function (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IIC Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Serial Communication Port Interface (SCP/SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Purpose I/O (GPIO) Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Universal Interrupt Controller (UIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ethernet Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Signal Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Signal Functional Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Ratings and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Spread Spectrum Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DDR 1/2 SDRAM I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
PCI Express (PCI-E) I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 3
Data Sheet
List of Figures
Figure 1. PPC405EX Embedded Controller Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 2. Package 27mm, 388-Ball EPBGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 3. Clocking Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 4. Input Setup and Hold Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 5. Output Delay and Float Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 6. Setup and Hold Timing Waveforms for RGMII Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 7. DDR SDRAM Simulation Signal Termination Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 8. DDR SDRAM Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 9. DDR SDRAM Read Data Path for a Single Data Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 10. DDR SDRAM Memory Data and DQS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 11. DDR SDRAM Read Cycle Timing—Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
PPC405EX – PowerPC 405EX Embedded Processor
4 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
List of Tables
Table 1. System Memory Address Map (4GB System Memory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 2. DCR Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 3. Signals Listed Alphabetically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 4. Signals Listed by Ball Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 5. Pin Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 6. Signal Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 7. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 8. Package Thermal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 9. Recommended DC Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 10. I/O Input Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 11. Typical DC Power Supply Requirements with DDR1 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 12. Maximum DC Power Supply Requirements with DDR1 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 13. Typical DC Power Supply Requirements with DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 14. Maximum DC Power Supply Requirements with DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 15. DC Power Supply Loads with DDR1 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 16. DC Power Supply Loads with DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 17. Power Contribution of Functional Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 18. System Clocking Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 19. Peripheral Interface I/O Clock Timings (not SDRAM or PCI-E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 20. RGMII I/O Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 21. I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 22. DDR SDRAM Output Driver Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 23. DDR SDRAM Write Operation Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 24. I/O Timing—DDR SDRAM TDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 25. I/O Timing—DDR SDRAM TSA and THA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 26. I/O Timing—DDR SDRAM Write Timing TSD and THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 27. I/O Timing—DDR SDRAM Read Timing TSD and THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Table 28. PCI-E Receiver I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 29. PCI-E Reference Clock I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 30. PCI-E Transmitter I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Table 31. Strapping Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 5
Data Sheet
Ordering, PVR, and JTAG Information
This section provides the part number nomenclature. For availability, contact your local AMCC sales office.
The part number contains a part modifier. Included in the modifier is a revision code. This refers to the die mask
revision number and is specified in the part numbering scheme for identification purposes only.
The PVR (Processor Version Register) and the JTAG ID register are software accessible (read-only) and contain
information that uniquely identifies the part. See the PPC405EX Embedded Processor User’s Manual for details
about accessing these registers.
Order Part Number Key
Product Name Order Part Number
(see Notes:) Package Rev
Level PVR Value JTAG ID
PPC405EX PPC405EX-SplfffT 27mm, 388-ball, EPBGA C 0x1291147F 0x1405B1E1
PPC405EX PPC405EX-NplfffT 27mm, 388-ball, EPBGA C 0x1291147D 0x1405B1E1
Notes:
1. S = security feature present, N = security feature not present.
2. p = Package: S = lead-free (RoHS compliant), P = leaded
3. l = Chip revision level: C = revision level C
4. fff = Processor frequency:
400 = 400MHz
533 = 533MHz
600 = 600MHz
5. T = Case temperature range, -40°C to +85°C (see footnote 5. on page 49)
AMCC Part Number
PPC405EX-SSC600T
Chip Package
Processor Speed (MHz)
Security
Case Temperature Range
Revision Level
Note: The example P/N above has the security feature, is lead-free, capable of running at 600MHz,
and is shipped in a tray (tape-and-reel not available).
PPC405EX – PowerPC 405EX Embedded Processor
6 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Block Diagram
Figure 1. PPC405EX Embedded Controller Functional Block Diagram
The PPC405EX is designed using the IBM Microelectronics Blue LogicTM methodology in which major functional
blocks are integrated together to create an ASIC (application-specific integrated circuit) product. This approach
provides a consistent way to create complex ASICs using IBM CoreConnectTM Bus Architecture.
DCR
GPIO
IICx2/
MAL/w
Ethernet
DMA
Bridges
Clock
Control
Reset
Power
Mgmt
JTAG Trace
Timers
MMU
Controller
OPB/PLB
Arbiter
(4-Channel)
DCRs
Arbiter
UART
x2
SCP
(SPI)
16KB I-Cache16KB D-Cache
On-chip Peripheral Bus (OPB)
Processor Local Bus (PLB4)—128 bits
Power PC
405 Processor
1Gbit
Bus BSC
MAC
x2
Interrupt
Controller
Universal
Security
Feature
HSS
PCI-E
Interrupt Coalescing
USB 2.0
Controller
NAND
Flash
Controller
EIP-94
SDRAM
Controller
DDR1/2
OTG
ULPI
GPT
EBMEBC
HSS
PCI-E
PKA/
TRNG
AHB-PLB
Bridge
1-lane 1-lane
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 7
Data Sheet
Address Maps
The PPC405EX incorporates two address maps. The first address map defines the possible use of addressable
memory regions that the processor can access. The second address map defines Device Configuration Register
(DCR) addresses (numbers). The DCRs are accessed by software running on the PPC405EX processor through
the use of mtdcr and mfdcr instructions.
Table 1. System Memory Address Map (4GB System Memory)
Function Subfunction Start Address (Hex) End Address (Hex) Size
Local Memory DDR 1/2 SDRAM 0 0000 0000 0 7FFF FFFF 2GB
EBC 0 8000 0000 0 8FFF FFFF 256MB
PCI Express 0 9000 0000 0 EF5F FFFF 1.6GB
OPB Peripherals
GPT 0 EF60 0000 0 EF60 01FF 512B
UART 0 0 EF60 0200 0 EF60 0207 8B
Reserved 0 EF60 0208 0 EF60 02FF 248B
UART 1 0 EF60 0300 0 EF60 0307 8B
Reserved 0 EF60 0308 0 EF60 03FF 248B
IIC 0 0 EF60 0400 0 EF60 041F 32B
Reserved 0 EF60 0420 0 EF60 04FF 224B
IIC 1 0 EF60 0500 0 EF60 051F 32B
Reserved 0 EF60 0520 0 EF60 05FF 224B
SCP 0 EF60 0600 0 EF60 0605 6B
Reserved 0 EF60 0606 0 EF60 06FF 250B
OPB Arbiter 0 EF60 0700 0 EF60 073F 64B
Reserved 0 EF60 0740 0 EF60 07FF 192B
GPIO 0 EF60 0800 0 EF60 087F 128B
Reserved 0 EF60 0880 0 EF60 08FF 128B
Ethernet 0 0 EF60 0900 0 EF60 09FF 256B
Ethernet 1 0 EF60 0A00 0 EF60 0AFF 256B
RGMII Bridge 0 EF60 0B00 0 EF60 0C03 260B
Reserved 0 EF60 0C04 0 EF60 FFFF 62KB
PLB/AHB Peripherals
PKA +TRNG 0 EF61 0000 0 EF61 FFFF 64KB
PCI Express Interrupt Handler 0 EF62 0000 0 EF62 00FF 256B
Reserved 0 EF62 0100 0 EF6B FFFF 640KB
USB OTG 0 EF6C 0000 0 EF6F FFFF 256KB
Security 0 EF70 0000 0 EF77 FFFF 512KB
Reserved 0 EF78 0000 0 EFFF FFFF 8.9MB
EBC EBC Memory 0 F000 0000 0 FFDF FFFF 254MB
EBC Memory—Boot ROM 0 FFE0 0000 0 FFFF FFFF 2MB
Notes:
1. If peripheral bus boot is selected, peripheral bank 0 is automatically configured at reset to the address range listed above.
2. After the boot process, software may reassign the boot memory regions for other uses.
3. PCI Express can use PLB address range 0x1 0000 0000 to 0xF FFFF FFFF even though the CPU can not access it.
PPC405EX – PowerPC 405EX Embedded Processor
8 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table 2. DCR Address Map
Function Start Address (Hex) End Address (Hex) Size
Total DCR Address Space10x000 0x3FF 1KW (4KB)1
Reserved 000 00B
CPR (Clocking, Power-on Reset) 00C 00D 2W
System DCRs 00E 00F 2W
DDR 1/2 SDRAM Controller 010 011 2W
External Bus Controller (EBC) 012 013 2W
External Bus Master (EBM) 014 015 2W
Reserved 016 01F
PLB4XAHB Bridge 020 02F 16W
Reserved 030 03F
PCI Express 0 040 05F 32W
PCI Express 1 060 07F 32W
PLB4 Arbiter 080 08F 16W
PLB-to-OPB Bridge 090 09F 16W
OPB-to-PLB Bridge 0A0 0A7 8W
Reserved 0A8 0AF
Power Management 0B0 0B2 3W
Reserved 0B3 0BF
UIC 0 0C0 0CF 16W
UIC 1 0D0 0DF 16W
UIC 2 0E0 0EF 16W
Reserved 0F0 0FF
DMA 100 13F 64W
Reserved 140 17F
Ethernet MAL 180 1FF 128W
Reserved 200 3FF
Notes:
1. A DCR address is 10 bits (1024 or 1K unique addresses). Each unique address represents a single 32-bit (word) register, or one kiloword
(KW) (which equals 4KB).
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 9
Data Sheet
PowerPC 405 Processor
The PPC405 processor is a fixed-point, 32-bit RISC unit.
Features include:
• Five-stage pipeline with single-cycle execution of most instructions, including loads and stores
• Separate, configurable 16 KB D- and I-caches, both two-way set associative
• Thirty-two 32-bit general purpose registers (GPRs)
• Unaligned load/store support
• Hardware multiply/divide
• Parity detection and reporting for the instruction cache, data cache, and translation look-aside buffer (TLB)
• Double word instruction fetch from cache
• Translation of the four GB logical address space into physical addresses
• Built-in timer and debug support
• Power management
• DCR interface is 32 bits wide
• Selectable processor vs. bus clock ratios (N:1 ratio only, where N =1, 2, 3,or 4)
Internal Buses
The PPC405EX contains four internal buses: the processor local bus (PLB), the Advanced High-Performance Bus
(AHB), the on-chip peripheral bus (OPB), and the device control register (DCR) bus. High performance devices
such as the processor, the DDR SDRAM memory controller, PCI Express, the Ethernet MAL, and DMA utilize the
PLB. Lower bandwidth I/O interfaces such as communications and timer interfaces utilize the OPB. The daisy-
chained DCR bus provides a lower bandwidth path for passing status and control information between the
processor and the other on-chip peripheral functions.
PLB
The Processor Local Bus (PLB) is a high-performance on-chip bus used to connect PLB-equipped master and
slave devices to the PPC405 CPU. It provides a 128-bit data path with 64-bit addressing and operates up to
200MHz. There are bridges between the PLB and the OPB.
Features include:
• Separate and simultaneous 6.4GB/s read and write data paths
• Decoupled address and data buses
• Address pipelining
• Late master request abort capability
• Hidden (overlapped) bus request/grant protocol
• Bus arbitration-locking mechanism
• Byte-enable capability allows for unaligned half word transfers and 3-B transfers
• Support for 32- and 64-B burst transfers
• Read word address capability
• Sequential burst protocol
• Guarded and unguarded memory transfers
• Simultaneous control, address, and data phases
• DMA buffered, flyby, peripheral-to-memory, memory-to-peripheral, and DMA memory-to-memory operations
AHB
The Advanced High-Performance Bus (AHB) is dedicated to the USB OTG 2.0.
Features include:
• 32-bit data path
• 32-bit address
• Synchronous to the PLB
• From 60MHz to 100MHz.
PPC405EX – PowerPC 405EX Embedded Processor
10 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
OPB
The OPB provides 32-bit address and data interfaces, and operates up to 100MHz. There are bridges between the
OPB and the PLB.
Features include:
• Pipelined read support
• Dynamic bus sizing
• Single-cycle data transfer between masters and slaves
DCR Bus
The daisy-chained DCR bus provides a path for passing status and control information between the processor core
and the other on-chip cores. All DCRs are 32 bits in width with 10-bit addressing.
External Bus Controller
The external bus controller (EBC and EBM) transfers data between the PLB and external memory or peripheral
devices attached to the external peripheral bus. The EBC provides direct attachment of memory devices such as
ROM and SRAM, DMA device paced memory devices, and DMA peripheral devices.
Features include:
• From 33MHz to 100 MHz speed
• Data bus is 8, 16, or 32 bits with a 27-bit address bus
• Up to four chip selects
• Arbitration and multi-master supported
• Flash ROM interface
• Boot from 8- or 16-bit NOR Flash support
• Direct support for 8-,16-, or 32-bit SRAM and external peripherals
• External bus master support
NAND Flash Controller
The NAND Flash controller (NDFC) provides a simple interface between the External Bus Controller (EBC) and a
variety of NAND Flash-based storage devices.
Features include:
• Attachment as internal EBC slave device
• Eight- and 16-bit NAND Flash interface
• Up to four banks of NAND Flash supported
• Device sizes:
– 4MB and larger supported for read/write access
– 4MB to 256MB supported for boot-from-NAND flash (size supported depends on addressing mode)
• 512B + 16B or 2kB + 64B device page sizes supported
• ECC generation - hamming code, single-bit correction, double-bit detection (SEC/DED)
• Eight-bit command write, address write, and data read/write
• Interrupt on device ready (after long page write or block erase operations)
• Boot from NAND
– Executes up to 4KB of boot code out of first block
– Automatic page read accesses performed based on device configuration and read address
DMA Controller
The Direct Memory Access (DMA) controller is a Processor Local Bus (PLB) master that enables faster data
transfer between memory and peripherals than is possible under program control. The 4-channel DMA controller
handles data transfers between memory and peripherals and from memory-to-memory. Each channel has an
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 11
Data Sheet
independent set of registers needed for data transfer: a control register, a source address register, a destination
address register, and a transfer count register.
Features include:
• Memory-to-memory transfers
• Buffered memory-to-peripheral transfers
• Buffered peripheral-to-memory transfers
• Four independent DMA channels
• Scatter/gather capability for dynamically programming multiple DMA transfers
• Programmable address increment or decrement
• Internal data buffering
• Can transfer data to/from any PLB slave, including the external bus
USB 2.0 OTG Interface
One USB 2.0 On-the-Go (OTG) controller that can be configured as either a Host or Device port.
Features include:
• Low- (Host only), Full- and High-Speed support
• Internal DMA to optimize performance and offload the CPU
• Up to two IN/OUT Endpoints in Device mode (one can be isochronous)
• Supports maximum packet size of 1024B (isochronous) and 512B (bulk)
• Support for isochronous traffic
• Three packets per microframe (24MB/s throughput)
• Eight KB buffer
• ULPI SDR interface
DDR1/2 SDRAM Controller
The Double Data Rate 1/2 (DDR1/2) SDRAM memory controller supports industry standard discrete devices that
are compatible with both the DDR1 or DDR2 specifications. The correct I/O supply voltage must be provided for the
two types of DDR devices: DDR1 devices require +2.5V and DDR2 devices require +1.8V.
Global memory timings, address and bank sizes, and memory addressing modes are programmable.
Features include:
• 16- or 32-bit memory interface
• Optional 8-bit error checking and correcting (ECC)
• 1.6-GB/s peak data rate
• Two memory banks of up to 1 GB each
• Maximum capacity of 2GB
• Support for one memory bank of 2GB with CAS latencies of 2, 2.5, or 3 for DDR1 interface, or 2, 3, 4, 5, 6, or 7
for DDR2 interface
• Clock frequencies from 133MHz (266Mbps) to 200MHz (400Mbps) supported
(Faster parts may be used, but must be clocked no faster than 200MHz)
• Page mode accesses (up to 16 open pages) with configurable paging policy
• Programmable address mapping and timing
• Software initiated self-refresh
• Power management (self-refresh, suspend)
• Two regions (two chip selects, one clock driver)
PPC405EX – PowerPC 405EX Embedded Processor
12 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
PCI Express
The PCI Express single-lane interfaces include the following features:
Features include:
• Compliant with PCI Express base specification 1.1
• Each PCI Express port can be End Point or Root Complex. (Upstream & Downstream)
– Applications compliant with MSI rules are limited to one End Point port per PPC405EX
• PCI-Express to PCI-Express opaque (Non-Transparent) bridge
• Power Management
• Supports one virtual channel (VC0) with no Traffic Class (TC) filtering
• Maximum Payload block size 256B
• Supports up to 512B maximum Read request size
• Requests supported:
– Up to two posted outbound Write requests (memory and messages)
– Up to two posted inbound Write requests
– Up to two outbound Read requests outstanding on PCI Express
– Up to two inbound Read requests outstanding on PCI Express
– Outbound I/O request as a PCI Express Root Port
– Inbound I/O request as a PCI Express End Point
• Buffering in each PCI Express Port for the following transaction types:
– 1KB Replay buffer: up to eight in flight transactions
– 512B for Outbound posted Writes
– 512B for Outbound Reads completion
– 512B for Inbound posted Writes
– 512B for Inbound Reads completion
• Parity checking on each buffer
• Programmable Outbound Memory (POM) Regions: 3 memory, 1 I/O, 1 message, 1 configuration, 1 internal
register
• Programmable Inbound Memory (PIM) Regions: 4 memory, 1 I/O, 1 expansion ROM
• INTx Interrupts support (PCI legacy):
– Up to four INTx Termination for Root Ports. A/B/C/D interrupts are wired to the UIC
– A/B/C/D INTx types Generation for Endpoints
• MSI - Message Signaled Interrupts
– MSI Generation for End Point
– MSI Termination for Root Ports
– MSI_X Termination for Root Ports
Security Function (optional)
The optional built-in security function is a cryptographic engine attached to the 128-bit PLB with built-in DMA and
interrupt controllers.
Features include:
• Federal Information Processing Standard (FIPS) 140-2 design
• Support for an unlimited number of Security Associations (SA)
• Different SA formats for each supported protocol (IPsec, SSL/TLS/DTLS, MACSec, SGT L2/L3 and sRTP)
• Internet Protocol Security (IPSec) features
– Full packet transforms (ESP & AH)
– Complete header and trailer processing (IPv4 and IPv6)
– Multi-mode automatic padding
– "Mutable bit" handler for AH, including IPv4 option and IPv6 extension headers
• Secure Socket Layer (SSL), Transport Layer Security (TLS), and Datagram Transport Layer Security (DTLS)
– Packet transforms
– One-pass hash-then-encrypt or decrypt-then-hash for SSL, TLS and DTLS packet transforms using ARC4
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 13
Data Sheet
Stream Cipher
• Secure Real-Time Protocol (sRTP) features
– Packet transforms
– ROC removal and TAG insertion
– Variable bypass offset of header length per packet
• Media Access Control Security (MACSec) features
– Cipher suite GCM-AES-128
– Header insertion and removal
– Integrity and confidentiality with MSDU
• SGT L2 supported features:
– GCM-AES with 128-bit key.
– Integrity only and with confidentiality of MSDU
• ICV generation and validation SGT L3 supported features
– AES-GCM, AES-GMAC with 128, 192 and 256 bit key.
• IPsec/SSL security acceleration engine
• DES, 3DES, AES, ARC-4, AES-GCM, and GMAC-AES encryption/decryption
• MD-5, SHA-1, and SHA-256 hashing
• Public key acceleration for RSA, DSA and Diffie-Hellman
• Combined encryption-hash and hash-decryption with the AES-CCM algorithm.
• True or pseudo random number generators
– Non-deterministic true random numbers
– Pseudo random numbers with lengths of 8B or 16B
– ANSI X9.17 Annex C compliant using a DES algorithm
• Interrupt controller
– Fifteen programmable, maskable interrupts
– Initiate commands via an input interrupt
– Sixteen programmable interrupts indicating completion of certain operations
– All interrupts mapped to one level- or edge-sensitive programmable interrupt output
• DMA controller
– Autonomous, 4-channel
– 1024-words (32 bits/word) per DMA transfer
– Scatter/gather capability with byte aligned addressing
– Byte reverse capability on SA and descriptors
UART
The Universal Asynchronous Receiver/Transmitter (UART) interface provides four configurations:
• One 8-signal port
• Two 4-signal ports.
• Two 2-signal ports
• One 4-signal port and one 2-signal port
The UART performs serial-to-parallel conversion on data received from a peripheral device or a modem, and
parallel-to-serial conversion on data received from the processor.
Features include:
• Compatible with the16750
• All six software modem control functions (CTS, RTS, DSR, DTR, RI, DCD) on UART0
• Programmable auto flow (data flow controlled by RTS and CTS signals)
• Characters can be 5, 6, 7, or 8 bits
• Programmable start, stop, parity bit insertion
• Sixty-four byte FIFOs for buffering Tx and Rx data
• LIN sub-bus specification compliant - line break generation/detection and false start bit detection
• Programmable internal/external loopback capabilities
• Low Power and Sleep mode
PPC405EX – PowerPC 405EX Embedded Processor
14 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
• Register conformance (after reset) to configuration of the NS16450 register set
• Hold and shift registers (eliminate need for precise synchronization between processor and serial data in
character mode)
• Complete status reporting
• Full prioritized interrupt system controls
• Independently controlled transmit, receive, line status, and data set interrupts
• Programmable baud generator (divides serial clock input and generates 16x clock)
• Ability to add/delete standard asynchronous communication bits such as start, stop, and parity to/from serial
data
• Even, odd, or no-parity bit generation and detection
• Stop bit generation of 1, 1.5, or 2 bits
• Variable baud rate
• Internal diagnostic capability
• Loopback controls for isolating communications link faults
• Break, parity, overrun, framing error simulation
• OPB interface with optional DMA support
IIC Bus Interface
The Inter-Integrated Circuit (IIC) interface provides a Philips I2C® compatible interface operating up to 400kHz
either as a master, a slave, or both with a bootstrap controller (BSC) included. During chip reset, the bootstrap
controller can read configuration data from an IIC compatible memory device (e.g., EEPROM). This data can be
used to replace the default configuration settings provided by the chip.
Features include:
• Two IIC channels
• Compliant with Philips Semiconductors I2C Specification, dated 1995
• Operation at 100kHz or 400kHz
• Byte (8-bit) data
• Addresses are 10 or 7 bits
• Slave Transmit and Receive
• Master Transmit and Receive
• Multiple bus masters supported
• Programmable as master, slave, or master/slave
• Boot parameters read from IIC attached memory (Port 0) with IIC bootstrap controller (BSC)
• OPB slave interface is 32 bits wide
Serial Communication Port Interface (SCP/SPI)
The Serial Communication Port (SCP) (also known as the Serial Peripheral Interface or SPI) is a full-duplex,
synchronous, character-oriented (byte) port that allows the exchange of data with other serial devices. The SCP is
a master on the serial port supporting a three-wire interface (receive, transmit, and clock), and is a slave on the
OPB.
Features include:
• One SCP channel, full duplex synchronous
•SCP master
• Up to 25MHz
• Programmable internal loopback capabilities
• Multi-master protocol supported
• Independent masking of all interrupts (master collision, transmit FIFO overflow, transmit FIFO empty, receive
FIFO full, receive FIFO underflow, receive FIFO overflow)
• Dynamic control of serial bit rate of data transfer (serial-master mode only)
• Data Item size for each data transfer under programmer control (4-to-16 bits)
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 15
Data Sheet
• OPB slave interface is 32 bits wide
General Purpose I/O (GPIO) Controller
The GPIO controller enables multiplexing of module I/O pins with multiple functions within the chip. That is, a single
package pin can be assigned to multiple I/O functions. Which function the pin is assigned to is determined by
register bit settings controlled by software. This significantly reduces the number of package pins needed to
support multiple I/O groups.
Features include:
• Up to 32 GPIOs available
– GPIOs are multiplexed with alternate functions
– If not in use for dedicated functions, I/Os are available as GPIOs
• Direct control of all functions from registers programmed by means of OPB bus master accesses
• Time multiplexing of controller outputs to module outputs
• Programmable conversion of module outputs to open-drain outputs (enables sharing of active low outputs
externally)
• Time multiplexing of module inputs to controller inputs
Universal Interrupt Controller (UIC)
The Universal Interrupt Controller (UIC) provides the control, status, and communications necessary between the
various sources of interrupts and the PPC405 processor.
Features include:
• Ten external interrupt sources supported
• Generate interrupt on level (high or low) or edge (rising or falling)
• Programmable as synchronous (edge-capture or level-sensitive) or asynchronous (edge- or level-sensitive
triggering)
• Each interrupt source/bit programmable as critical or non critical
• DCR bus interface is 32 bits wide
• Optional interrupt handler vector generation
– Programmable vector base address
– Programmable vector offset size
– Programmable interrupt priority ordering
• Programmable polarity for all interrupt types
• Interrupts of the same type do not need to be in contiguous bit positions
• Status registers provide: current state of all interrupts, current state of enabled interrupts
Ethernet Controller
The Ethernet support provides two 10/100/1000 Mbps interfaces (GMII/MII/RGMII).
Features include:
• ANSI/IEEE Std. 802.3 and IEEE 802.3u supplement compliant
• Half-duplex and full-duplex support for the following:
– One Gigabit Media Independent Interface (GMII)
– One Media Independent Interface (MII)
– Two Reduced GMII interfaces (RGMII)
• Receive and transmit FIFOs are 16K bytes each with programmable thresholds
• FCS control for transmit/receive packets
• Multiple packet handling in transmit and receive FIFOs
• Unicast, multicast, broadcast, and promiscuous address filtering
• Two 256-bit hash filters for unicast and multicast frames
• Automatic retransmission of collided frames
PPC405EX – PowerPC 405EX Embedded Processor
16 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
• Runt frame rejection
• Programmable inter-frame gap
• IEEE 802.3x compliant for frame-based flow control mechanism, including self-assembled control frame
transmitting)
• Wake-on-LAN and Power-over-Internet supported
• Programmable internal/external loopback capabilities
• OPB slave (MAC) and PLB master (MAL) interfaces for control and configuration are 32 bits wide
• MAL has 128-bit PLB master interface for data path.
• Extensive error/status vector generation for each processed packet
• VLAN tag ID supported (according to IEEE Draft 802.3ac/D1.0 standard)
• Programmable automatic source address inclusion/replacement for transmit packets
• Programmable automatic Pad/FCS stripping for receive packets
• Programmable VLAN Tag inclusion/replacement for transmit packets
• Half- or full-duplex GMII/RGMII
• Jumbo frames support
• Memory Access Layer (MAL) provides DMA capability to Ethernet channel
• Interrupt coalescence support for two transmit and two receive channels
General Purpose Timer (GPT)
The GPT provides a time base counter and system timers in addition to those defined in the processor.
Features include:
• 32-bit time base counter driven by the OPB clock
• Seven 32-bit compare timers
JTAG
Features include:
• IEEE 1149.1 test access port
• JTAG Boundary Scan Description Language (BSDL)
Refer to http://www.amcc.com/Embedded/Partners for a list of AMCC partners supplying probes for use with the
JTAG interface.
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 17
Data Sheet
Figure 2. Package 27mm, 388-Ball EPBGA
Bottom View
A
1.0 Basic
0.60 ± 0.1 SOLDERBALL x 388
27.0
27.0 ± 0.2
BC
DE
FG
HJ
KL
M
AA
N
PR
TU
VW
Y
AB
01 03 05 07 09 11 13 15 17 19
02 04 06 08 10 12 14 16 18
21
20 22
25.0 REF
0.5 ± 0.1
PCB
Substrate
Epoxy Mold
Compound 2.65 max
®
PPC405EX
Part Number
1YWWBZZZZZ
Lot Number
23
24
25
26
AC
AD AE
AF
Top View
Notes:
1.
All dimensions are in mm.
Gold Gate Release
Corresponds to
A01 Ball Location
2. Package conforms to JEDEC MS-034C
Logo View
3. Package available in leaded or lead-free versions
Side View
0.56 REF
Seating plane
C
0.2 C
PPC405EX – PowerPC 405EX Embedded Processor
18 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Signal Lists
The following table lists all the external signals in alphabetical order and shows the ball (pin) number on which the
signal appears. Shared signals are shown with the default signal (following reset) not in brackets and the alternate
signal in brackets. Signals that have different functions for different modes with the same function are separated by
commas.
Shared signals appear alphabetically multiple times in the list—once for each signal name on the ball. The Page
column indicates the page within the table “Signal Functional Description” on page 39 on which the signals in the
indicated interface group begin.
Table 3. Signals Listed Alphabetically (Sheet 1 of 13)
Signal Name Ball Interface Group Page
AGND K01
Power 45
AGND L04
AGND P04
AGND R01
AHVDD M04 Power 45
AHVDD R04
AVDD J03
Power 45
AVDD K04
AVDD M01
AVDD N03
AVDD N04
AVDD P01
AVDD T01
BA0 AD22
DDR 1/2 SDRAM 43BA1 AF24
BA2 AE24
BankSel0 AF21 DDR 1/2 SDRAM 43
BankSel1 AE20
[BusReq]GPIO27[DMAEOT3][IRQ5] B03 External Bus Master 42
CAS AF20 DDR 1/2 SDRAM 43
DM0 M25
DDR 1/2 SDRAM 43
DM1 T26
DM2 AD16
DM3 AD13
DM4 Y26
[DMAAck0]PerAddr07[TS1] J26
DMA 42
[DMAAck1]GPIO31[IRQ0] D01
[DMAAck2]GPIO22[HoldReq] B05
[DMAAck3]GPIO25[ExtAck][IRQ3] C04
[DMAEOT0]GPIO26[PerAddr05][TS3] K26
DMA 42
[DMAEOT1]GPIO29[IRQ2] D03
[DMAEOT2]GPIO24[ExtReq][IRQ4] A03
[DMAEOT3]GPIO27[BusReq][IRQ5] B03
[DMAReq0]PerAddr06[TS2] K25
DMA 42
[DMAReq1]GPIO30[IRQ1] D02
[DMAReq2]GPIO23[HoldAck] C05
[DMAReq3]PerAddr08[TS0] J25
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 19
Data Sheet
DQS0 M26
DDR 1/2 SDRAM 43
DQS1 T25
DQS2 AE16
DQS3 AE12
DQS4 Y25
EAGND AE07 Power 45
EAVDD AE08
ECC0 V24
DDR 1/2 SDRAM 43
ECC1 W24
ECC2 AB26
ECC3 AB25
ECC4 V25
ECC5 W25
ECC6 AA26
ECC7 AA25
EOVDD D12
Power 45
EOVDD T12
EOVDD AC05
EOVDD AB04
EOVDD AC07
EOVDD AC08
[ExtAck]GPIO25[DMAAck3][IRQ3] C04
External Bus Master 42[ExtReq]GPIO24[DMAEOT2][IRQ4] A03
ExtReset B19
Table 3. Signals Listed Alphabetically (Sheet 2 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor
20 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
GMCCD, GMC1RxClk AD04
Ethernet 39
GMCCrS, GMC1TxClk AF04
GMCGTxClk, GMC0TxClk AE04
GMCMDClk AE03
GMCMDIO AF02
GMCRefClk AD07
GMCRxClk, GMC0RxClk AD09
GMCRxD0, GMC0RxD0 AC11
GMCRxD1, GMC0RxD1 AE10
GMCRxD2, GMC0RxD2 AD10
GMCRxD3, GMC0RxD3 AF09
GMCRxD4, GMC1RxD0 AE09
GMCRxD5, GMC1RxD1 AF07
GMCRxD6, GMC1RxD2 AF06
GMCRxD7, GMC1RxD3 AE06
GMCRxDV, GMC0RxCtl AE05
GMCRxEr, GMC1RxCtl AF05
GMCTxClk AC06
GMCTxD0, GMC0TxD0 AE01
GMCTxD1, GMC0TxD1 AD02
GMCTxD2, GMC0TxD2 AD01
GMCTxD3, GMC0TxD3 AC03
GMCTxD4, GMC1TxD0 AC02
GMCTxD5, GMC1TxD1 AC01
GMCTxD6, GMC1TxD2 AB03
GMCTxD7, GMC1TxD3 AB02
GMCTxEn, GMC0TxCtl AD05
GMCTxEr, GMC1TxCtl AF03
Table 3. Signals Listed Alphabetically (Sheet 3 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 21
Data Sheet
GND A01
Power 45
GND A08
GND A13
GND A19
GND A26
GND B01
GND B02
GND B25
GND C01
GND C02
GND C03
GND C24
GND D04
GND D09
GND D14
GND D18
GND D23
GND E01
GND E03
GND H01
GND H26
GND J04
GND J23
GND K24
GND L11
GND L13
GND L16
GND M12
GND M13
GND M14
GND M15
GND N12
GND N13
GND N14
GND N15
GND N16
GND N26
GND P11
GND P12
GND P13
GND P14
GND P15
GND P23
Table 3. Signals Listed Alphabetically (Sheet 4 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor
22 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
GND R12
Power 45
GND R13
GND R14
GND R15
GND T11
GND T14
GND T16
GND U01
GND U02
GND V04
GND V23
GND W01
GND W26
GND AB01
GND AC04
GND AC09
GND AC13
GND AC18
GND AC23
GND AD03
GND AD24
GND AE02
GND AE25
GND AF01
GND AF08
GND AF14
GND AF19
GND AF26
Table 3. Signals Listed Alphabetically (Sheet 5 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 23
Data Sheet
GPIO00[PerDataPar0] A16
System 41
GPIO01[PerDataPar1] B12
GPIO02[PerDataPar2] C09
GPIO03[PerDataPar3] B04
GPIO04[PerData20][USB2Data4] C13
GPIO05[PerData21][USB2Data5] B09
GPIO06[PerData22][USB2Data6] C12
GPIO07[PerData23][USB2Data7] D11
GPIO08[PerCS1][NFCE1][IRQ7] C20
GPIO09[PerCS2][NFCE2][IRQ8] A21
GPIO10[PerCS3][NFCE3][IRQ9] B20
GPIO11[IRQ6] H03
GPIO12[PerData16][USB2Data0] C11
GPIO13[PerData17][USB2Data1] B08
GPIO14[PerData18][USB2Data2] A10
GPIO15[PerData19][USB2Data3] B10
GPIO16[UART0DCD][UART1CTS]F04
GPIO17[UART0DSR][UART1RTS]F02
GPIO18[UART0CTS]G02
GPIO19[UART0RTS]G01
GPIO20[UART0DTR][UART1Tx] F03
GPIO21[UART0RI][UART1Rx] F01
GPIO22[HoldReq][DMAAck2] B05
GPIO23[HoldAck][DMAReq2] C05
GPIO24[ExtReq][DMAEOT2][IRQ4] A03
GPIO25[ExtAck][DMAAck3][IRQ3] C04
GPIO26[PerAddr05][DMAEOT0][TS3] K26
GPIO27[BusReq][DMAEOT3][IRQ5] B03
GPIO28 U03
GPIO29[DMAEOT1][IRQ2] D03
GPIO30[DMAReq1][IRQ1] D02
GPIO31[DMAAck1][IRQ0] D01
Halt A02 System 41
[HoldAck]GPIO23[DMAReq2] C05 External Bus Master 42
[HoldReq]GPIO22[DMAAck2] B05
IIC0SData AA01
IIC 39
IIC0SClk Y03
IIC1SData[SCPDO] AA04
IIC1SClk[SCPClkOut] AA02
Table 3. Signals Listed Alphabetically (Sheet 6 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor
24 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
[IRQ0]GPIO31[DMAAck1] D01
Interrupts 40
[IRQ1]GPIO30[DMAReq1] D02
[IRQ2]GPIO29[DMAEOT1] D03
[IRQ3]GPIO25[ExtAck][DMAAck3] C04
[IRQ4]GPIO24[ExtReq][DMAEOT2] A03
[IRQ5]GPIO27[BusReq][DMAEOT3] B03
[IRQ6]GPIO11 H03
[IRQ7][PerCS1][NFCE1]GPIO08 C20
[IRQ8][PerCS2][NFCE2]GPIO09 A21
[IRQ9][PerCS3][NFCE3]GPIO10 B20
MemAddr00 AE21
DDR1/2 SDRAM 43
MemAddr01 AD20
MemAddr02 AF22
MemAddr03 AE22
MemAddr04 AF23
MemAddr05 AD21
MemAddr06 AC21
MemAddr07 AE23
MemAddr08 AE26
MemAddr09 AD25
MemAddr10 AD26
MemAddr11 AC24
MemAddr12 AB24
MemAddr13 AC25
MemAddr14 AC26
MemClkEn Y24
DDR1/2 SDRAM 43MemClkOut0 AA23
MemClkOut0 AA24
Table 3. Signals Listed Alphabetically (Sheet 7 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 25
Data Sheet
MemData00 M24
DDR1/2 SDRAM 43
MemData01 N24
MemData02 P25
MemData03 P24
MemData04 L25
MemData05 L26
MemData06 N25
MemData07 P26
MemData08 R24
MemData09 T24
MemData10 V26
MemData11 U24
MemData12 R25
MemData13 R26
MemData14 U26
MemData15 U25
MemData16 AE17
MemData17 AF17
MemData18 AE15
MemData19 AF15
MemData20 AF18
MemData21 AD17
MemData22 AF16
MemData23 AD15
MemData24 AE13
MemData25 AF12
MemData26 AF10
MemData27 AD11
MemData28 AE14
MemData29 AF13
MemData30 AF11
MemData31 AE11
MemFBD AD23
DDR1/2 SDRAM 43
MemFBR AF25
MemODT0 AD18
MemODT1 AE18
Table 3. Signals Listed Alphabetically (Sheet 8 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor
26 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
[NFALE]PerData30 C06
NAND Flash 43
[NFCE0]PerCS0 B21
[NFCE1][PerCS1]GPIO08[IRQ7] C20
[NFCE2][PerCS2]GPIO09[IRQ8] A21
[NFCE3][PerCS3]GPIO10[IRQ9] B20
[NFCLE]PerData29 A06
[NFData00]PerData00 C18
[NFData01]PerData01 B18
[NFData02]PerData02 C17
[NFData03]PerData03 A18
[NFData04]PerData04 D16
[NFData05]PerData05 B17
[NFData06]PerData06 C16
[NFData07]PerData07 B16
[NFData08]PerData08 A17
[NFData09]PerData09 B15
[NFData10]PerData10 C15
[NFData11]PerData11 A15
[NFData12]PerData12 B14
[NFData13]PerData13 A14
[NFData14]PerData14 C14
[NFData15]PerData15 B13
[NFRdyBusy]PerData31 A04
[NFREn]PerData27 A05
[NFWEn]PerData28 C08
OVDD D05
Power 45
OVDD D07
OVDD D08
OVDD D13
OVDD D19
OVDD D20
OVDD D22
OVDD E04
OVDD E23
OVDD G04
OVDD G23
OVDD H23
OVDD L12
OVDD L15
OVDD M11
OVDD M16
OVDD R11
OVDD V03
OVDD W04
OVDD Y04
Table 3. Signals Listed Alphabetically (Sheet 9 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 27
Data Sheet
PCIE0ATB L03
PCI Express 0 40
PCIE0ClkC L01
PCIE0ClkT L02
PCIE0RExt M03
PCIE0RExtG M02
PCIE0Rx J01
PCIE0Rx J02
PCIE0Tx K02
PCIE0Tx K03
PCIE1ATB R02
PCI Express 1 40
PCIE1ClkC T02
PCIE1ClkT R03
PCIE1RExt T03
PCIE1RExtG T04
PCIE1Rx N01
PCIE1Rx N02
PCIE1Tx P02
PCIE1Tx P03
[PerAddr05]GPIO26[TS3][DMAEOT0] K26
External Peripheral 42
PerAddr06[DMAReq0][TS2] K25
PerAddr07[DMAAck0][TS1] J26
PerAddr08[DMAReq3][TS0] J25
PerAddr09[TS1E] H25
PerAddr10[TS0E] J24
PerAddr11[TS1O] G26
PerAddr12[TS0O] H24
PerAddr13 G25
PerAddr14 F26
PerAddr15 E26
PerAddr16 F25
PerAddr17 G24
PerAddr18 E25
PerAddr19 D26
PerAddr20 F24
PerAddr21 C26
PerAddr22 D25
PerAddr23 F23
PerAddr24 E24
PerAddr25 C25
PerAddr26 D24
PerAddr27 B26
PerAddr28 A25
PerAddr29 B24
PerAddr30 C23
PerAddr31 C22
PerBLast D21 External Peripheral 42
PerClk A20
Table 3. Signals Listed Alphabetically (Sheet 10 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor
28 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
PerCS0[NFCE0]B21
External Peripheral 42
[PerCS1][NFCE1]GPIO08[IRQ7] C20
[PerCS2][NFCE2]GPIO09[IRQ8] A21
[PerCS3][NFCE3]GPIO10[IRQ9] B20
PerData00[NFData00] C18
External Peripheral 42
PerData01[NFData01] B18
PerData02[NFData02] C17
PerData03[NFData03] A18
PerData04[NFData04] D16
PerData05[NFData05] B17
PerData06[NFData06] C16
PerData07[NFData07] B16
PerData08[NFData08] A17
PerData09[NFData09] B15
PerData10[NFData10] C15
PerData11[NFData11] A15
PerData12[NFData12] B14
PerData13[NFData13] A14
PerData14[NFData14] C14
PerData15[NFData15] B13
[PerData16]GPIO12[USB2Data0] C11
[PerData17]GPIO13[USB2Data1] B08
[PerData18]GPIO14[USB2Data2] A10
[PerData19]GPIO15[USB2Data3] B10
[PerData20]GPIO04[USB2Data4] C13
[PerData21]GPIO05[USB2Data5] B09
[PerData22]GPIO06[USB2Data6] C12
[PerData23]GPIO07[USB2Data7] D11
PerData24[USB2Dir] A07
PerData25[USB2Stop] B07
PerData26[USB2Next] B06
PerData27[NFREn]A05
PerData28[NFWEn]C08
PerData29[NFCLE] A06
PerData30[NFALE] C06
PerData31[NFRdyBusy]A04
[PerDataPar0]GPIO00 A16
External Peripheral 42
[PerDataPar1]GPIO01 B12
[PerDataPar2]GPIO02 C09
[PerDataPar3]GPIO03 B04
PerErr C19
External Peripheral 42
PerOE A24
PerReady B11
PerRW B23
PerWBE0 A23
External Peripheral 42
PerWBE1 C21
PerWBE2 B22
PerWBE3 A22
Table 3. Signals Listed Alphabetically (Sheet 11 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 29
Data Sheet
PSROUser A09 System 41
RAS AD19 DDR 1/2 SDRAM 43
Reserved AD12 Other 45
SAGND A11 Power 45
SAVDD A12
[SCPClkOut]IIC1SClk AA02
Serial Communication Port 44SCPDI AA03
[SCPDO]IIC1SData AA04
SVDD N23
Power 45
SVDD R16
SVDD T15
SVDD W23
SVDD Y23
SVDD AB23
SVDD AC19
SVDD AC20
SVDD AC22
SVDD AD14
SVREF1A AC14
DDR1/2 SDRAM 43
SVREF1B T23
SVREF2A AC16
SVREF2B L23
SysClk C10
System 41SysErr AD06
SysReset AD08
TCK V02
JTAG 40TDI W02
TDO W03
TestEn Y02 System 41
TmrClk D06
TMS V01 JTAG 40
TrcClk L24 Trace 41
TRST Y01 JTAG 40
[TS0]PerAddr08[DMAReq3] J25
Trace 41
[TS1]PerAddr07[DMAAck0] J26
[TS2]PerAddr06[DMAReq0] K25
[TS3]GPIO26[PerAddr05][DMAEOT0] K26
[TS0E]PerAddr10 J24
Trace 41
[TS0O]PerAddr12 H24
[TS1E]PerAddr09 H25
[TS1O]PerAddr11 G26
Table 3. Signals Listed Alphabetically (Sheet 12 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor
30 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
[UART0CTS]GPIO18 G02
UART Peripheral 44
[UART0DCD]GPIO16[UART1CTS]F04
[UART0DSR]GPIO17[UART1RTS]F02
[UART0DTR]GPIO20[UART1Tx] F03
[UART0RI]GPIO21[UART1Rx] F01
[UART0RTS]GPIO19 G01
UART0Rx G03
UART0Tx H02
[UART1CTS]GPIO16[UART0DCD]F04
UART Peripheral 44
[UART1RTS]GPIO17[UART0DSR]F02
[UART1Rx]GPIO21[UART0RI]F01
[UART1Tx]GPIO20[UART0DTR]F03
UARTSerClk E02 UART Peripheral 44
USB2Clk C07 USB 2.0 44
[USB2Data0]GPIO12[PerData16] C11
USB 2.0 44
[USB2Data1]GPIO13[PerData17] B08
[USB2Data2]GPIO14[PerData18] A10
[USB2Data3]GPIO15[PerData19] B10
[USB2Data4]GPIO04[PerData20] C13
[USB2Data5]GPIO05[PerData21] B09
[USB2Data6]GPIO06[PerData22] C12
[USB2Data7]GPIO07[PerData23] D11
[USB2Dir]PerData24 A07
USB 2.0 44[USB2Next]PerData26 B06
[USB2Stop]PerData25 B07
VDD D10
Power 45
VDD D15
VDD D17
VDD H04
VDD K23
VDD L14
VDD M23
VDD N11
VDD P16
VDD R23
VDD T13
VDD U04
VDD U23
VDD AC10
VDD AC12
VDD AC15
VDD AC17
WE AE19 DDR1/2 SDRAM 43
Table 3. Signals Listed Alphabetically (Sheet 13 of 13)
Signal Name Ball Interface Group Page
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 31
Data Sheet
In the following table, only the default signal name is shown for each ball. Shared balls are marked with an asterisk
(*). To determine what signals or functions are shared on those balls, look up the default signal name in “Signals
Listed Alphabetically” on page 18. The following table lists the signals by ball assignment.
Table 4. Signals Listed by Ball Assignment (Sheet 1 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
A01 GND B01 GND C01 GND D01 GPIO31 *
A02 Halt B02 GND C02 GND D02 GPIO30 *
A03 GPIO24 * B03 GPIO27 * C03 GND D03 GPIO29 *
A04 PerData31 * B04 GPIO03 * C04 GPIO25 * D04 GND
A05 PerData27 * B05 GPIO22 * C05 GPIO23 * D05 OVDD
A06 PerData29 * B06 PerData26 * C06 PerData30 * D06 TmrClk
A07 PerData24 * B07 PerData25 * C07 USB2Clk D07 OVDD
A08 GND B08 GPIO13 * C08 PerData28 * D08 OVDD
A09 PSROUser B09 GPIO05 * C09 GPIO02 * D09 GND
A10 GPIO14 * B10 GPIO15 * C10 SysClk D10 VDD
A11 SAGND B11 PerReady C11 GPIO12 * D11 GPIO07 *
A12 SAVDD B12 GPIO01 * C12 GPIO06 * D12 EOVDD
A13 GND B13 PerData15 * C13 GPIO04 * D13 OVDD
A14 PerData13 * B14 PerData12 * C14 PerData14 * D14 GND
A15 PerData11 * B15 PerData09 * C15 PerData10 * D15 VDD
A16 GPIO00 * B16 PerData07 * C16 PerData06 * D16 PerData04 *
A17 PerData08 * B17 PerData05 * C17 PerData02 * D17 VDD
A18 PerData03 * B18 PerData01 * C18 PerData00 * D18 GND
A19 GND B19 ExtReset C19 PerErr D19 OVDD
A20 PerClk B20 GPIO10 * C20 GPIO08 * D20 OVDD
A21 GPIO09 * B21 PerCS0 * C21 PerWBE1 D21 PerBLast
A22 PerWBE3 B22 PerWBE2 C22 PerAddr31 D22 OVDD
A23 PerWBE0 B23 PerRW C23 PerAddr30 D23 GND
A24 PerOE B24 PerAddr29 C24 GND D24 PerAddr26
A25 PerAddr28 B25 GND C25 PerAddr25 D25 PerAddr22
A26 GND B26 PerAddr27 C26 PerAddr21 D26 PerAddr19
PPC405EX – PowerPC 405EX Embedded Processor
32 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
E01 GND F01 GPIO21 * G01 GPIO19 * H01 GND
E02 UARTSerClk F02 GPIO17 * G02 GPIO18 * H02 UART0Tx *
E03 GND F03 GPIO20 * G03 UART0Rx * H03 GPIO11 *
E04 OVDD F04 GPIO16 * G04 OVDD H04 VDD
E05 No ball F05 No ball G05 No ball H05 No ball
E06 No ball F06 No ball G06 No ball H06 No ball
E07 No ball F07 No ball G07 No ball H07 No ball
E08 No ball F08 No ball G08 No ball H08 No ball
E09 No ball F09 No ball G09 No ball H09 No ball
E10 No ball F10 No ball G10 No ball H10 No ball
E11 No ball F11 No ball G11 No ball H11 No ball
E12 No ball F12 No ball G12 No ball H12 No ball
E13 No ball F13 No ball G13 No ball H13 No ball
E14 No ball F14 No ball G14 No ball H14 No ball
E15 No ball F15 No ball G15 No ball H15 No ball
E16 No ball F16 No ball G16 No ball H16 No ball
E17 No ball F17 No ball G17 No ball H17 No ball
E18 No ball F18 No ball G18 No ball H18 No ball
E19 No ball F19 No ball G19 No ball H19 No ball
E20 No ball F20 No ball G20 No ball H20 No ball
E21 No ball F21 No ball G21 No ball H21 No ball
E22 No ball F22 No ball G22 No ball H22 No ball
E23 OVDD F23 PerAddr23 G23 OVDD H23 OVDD
E24 PerAddr24 F24 PerAddr20 G24 PerAddr17 H24 PerAddr12 *
E25 PerAddr18 F25 PerAddr16 G25 PerAddr13 H25 PerAddr09 *
E26 PerAddr15 F26 PerAddr14 G26 PerAddr11 * H26 GND
Table 4. Signals Listed by Ball Assignment (Sheet 2 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 33
Data Sheet
J01 PCIE0Rx K01 AGND L01 PCIE0ClkC M01 AVDD
J02 PCIE0Rx K02 PCIE0Tx L02 PCIE0ClkT M02 PCIE0RExtG
J03 AVDD K03 PCIE0Tx L03 PCIE0ATB M03 PCIE0RExt
J04 GND K04 AVDD L04 AGND M04 AHVDD
J05 No ball K05 No ball L05 No ball M05 No ball
J06 No ball K06 No ball L06 No ball M06 No ball
J07 No ball K07 No ball L07 No ball M07 No ball
J08 No ball K08 No ball L08 No ball M08 No ball
J09 No ball K09 No ball L09 No ball M09 No ball
J10 No ball K10 No ball L10 No ball M10 No ball
J11 No ball K11 No ball L11 GND M11 OVDD
J12 No ball K12 No ball L12 OVDD M12 GND
J13 No ball K13 No ball L13 GND M13 GND
J14 No ball K14 No ball L14 VDD M14 GND
J15 No ball K15 No ball L15 OVDD M15 GND
J16 No ball K16 No ball L16 GND M16 OVDD
J17 No ball K17 No ball L17 No ball M17 No ball
J18 No ball K18 No ball L18 No ball M18 No ball
J19 No ball K19 No ball L19 No ball M19 No ball
J20 No ball K20 No ball L20 No ball M20 No ball
J21 No ball K21 No ball L21 No ball M21 No ball
J22 No ball K22 No ball L22 No ball M22 No ball
J23 GND K23 VDD L23 SVREF2B M23 VDD
J24 PerAddr10 * K24 GND L24 TrcClk M24 MemData00
J25 PerAddr08 * K25 PerAddr06 * L25 MemData04 M25 DM0
J26 PerAddr07 * K26 GPIO26 * L26 MemData05 M26 DQS0
Table 4. Signals Listed by Ball Assignment (Sheet 3 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
PPC405EX – PowerPC 405EX Embedded Processor
34 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
N01 PCIE1Rx P01 AVDD R01 AGND T01 AVDD
N02 PCIE1Rx P02 PCIE1Tx R02 PCIE1ATB T02 PCIE1ClkC
N03 AVDD P03 PCIE1Tx R03 PCIE1ClkT T03 PCIE1RExt
N04 AVDD P04 AGND R04 AHVDD T04 PCIE1RExtG
N05 No ball P05 No ball R05 No ball T05 No ball
N06 No ball P06 No ball R06 No ball T06 No ball
N07 No ball P07 No ball R07 No ball T07 No ball
N08 No ball P08 No ball R08 No ball T08 No ball
N09 No ball P09 No ball R09 No ball T09 No ball
N10 No ball P10 No ball R10 No ball T10 No ball
N11 VDD P11 GND R11 OVDD T11 GND
N12 GND P12 GND R12 GND T12 EOVDD
N13 GND P13 GND R13 GND T13 VDD
N14 GND P14 GND R14 GND T14 GND
N15 GND P15 GND R15 GND T15 SVDD
N16 GND P16 VDD R16 SVDD T16 GND
N17 No ball P17 No ball R17 No ball T17 No ball
N18 No ball P18 No ball R18 No ball T18 No ball
N19 No ball P19 No ball R19 No ball T19 No ball
N20 No ball P20 No ball R20 No ball T20 No ball
N21 No ball P21 No ball R21 No ball T21 No ball
N22 No ball P22 No ball R22 No ball T22 No ball
N23 SVDD P23 GND R23 VDD T23 SVREF1B
N24 MemData01 P24 MemData03 R24 MemData08 T24 MemData09
N25 MemData06 P25 MemData02 R25 MemData12 T25 DQS1
N26 GND P26 MemData07 R26 MemData13 T26 DM1
Table 4. Signals Listed by Ball Assignment (Sheet 4 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 35
Data Sheet
U01 GND V01 TMS W01 GND Y01 TRST
U02 GND V02 TCK W02 TDI Y02 TestEn
U03 GPIO28 V03 OVDD W03 TDO Y03 IIC0SClk
U04 VDD V04 GND W04 OVDD Y04 OVDD
U05 No ball V05 No ball W05 No ball Y05 No ball
U06 No ball V06 No ball W06 No ball Y06 No ball
U07 No ball V07 No ball W07 No ball Y07 No ball
U08 No ball V08 No ball W08 No ball Y08 No ball
U09 No ball V09 No ball W09 No ball Y09 No ball
U10 No ball V10 No ball W10 No ball Y10 No ball
U11 No ball V11 No ball W11 No ball Y11 No ball
U12 No ball V12 No ball W12 No ball Y12 No ball
U13 No ball V13 No ball W13 No ball Y13 No ball
U14 No ball V14 No ball W14 No ball Y14 No ball
U15 No ball V15 No ball W15 No ball Y15 No ball
U16 No ball V16 No ball W16 No ball Y16 No ball
U17 No ball V17 No ball W17 No ball Y17 No ball
U18 No ball V18 No ball W18 No ball Y18 No ball
U19 No ball V19 No ball W19 No ball Y19 No ball
U20 No ball V20 No ball W20 No ball Y20 No ball
U21 No ball V21 No ball W21 No ball Y21 No ball
U22 No ball V22 No ball W22 No ball Y22 No ball
U23 VDD V23 GND W23 SVDD Y23 SVDD
U24 MemData11 V24 ECC0 W24 ECC1 Y24 MemClkEn
U25 MemData15 V25 ECC4 W25 ECC5 Y25 DQS4
U26 MemData14 V26 MemData10 W26 GND Y26 DM4
Table 4. Signals Listed by Ball Assignment (Sheet 5 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
PPC405EX – PowerPC 405EX Embedded Processor
36 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
AA01 IIC0SData AB01 GND AC01 GMCTxD5 * AD01 GMCTxD2 *
AA02 IIC1SClk * AB02 GMCTxD7 * AC02 GMCTxD4 * AD02 GMCTxD1 *
AA03 SCPDI AB03 GMCTxD6 * AC03 GMCTxD3 * AD03 GND
AA04 IIC1SData * AB04 EOVDD AC04 GND AD04 GMCCD *
AA05 No ball AB05 No ball AC05 EOVDD AD05 GMCTxEn *
AA06 No ball AB06 No ball AC06 GMCTxClk AD06 SysErr
AA07 No ball AB07 No ball AC07 EOVDD AD07 GMCRefClk
AA08 No ball AB08 No ball AC08 EOVDD AD08 SysReset
AA09 No ball AB09 No ball AC09 GND AD09 GMCRxClk *
AA10 No ball AB10 No ball AC10 VDD AD10 GMCRxD2 *
AA11 No ball AB11 No ball AC11 GMCRxD0 * AD11 MemData27
AA12 No ball AB12 No ball AC12 VDD AD12 Reserved
AA13 No ball AB13 No ball AC13 GND AD13 DM3
AA14 No ball AB14 No ball AC14 SVREF1A AD14 SVDD
AA15 No ball AB15 No ball AC15 VDD AD15 MemData23
AA16 No ball AB16 No ball AC16 SVREF2A AD16 DM2
AA17 No ball AB17 No ball AC17 VDD AD17 MemData21
AA18 No ball AB18 No ball AC18 GND AD18 MemODT0
AA19 No ball AB19 No ball AC19 SVDD AD19 RAS
AA20 No ball AB20 No ball AC20 SVDD AD20 MemAddr01
AA21 No ball AB21 No ball AC21 MemAddr06 AD21 MemAddr05
AA22 No ball AB22 No ball AC22 SVDD AD22 BA0
AA23 MemClkOut0 AB23 SVDD AC23 GND AD23 MemFBD
AA24 MemClkOut0 AB24 MemAddr12 AC24 MemAddr11 AD24 GND
AA25 ECC7 AB25 ECC3 AC25 MemAddr13 AD25 MemAddr09
AA26 ECC6 AB26 ECC2 AC26 MemAddr14 AD26 MemAddr10
Table 4. Signals Listed by Ball Assignment (Sheet 6 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 37
Data Sheet
AE01 GMCTxD0 * AF01 GND
AE02 GND AF02 GMCMDIO
AE03 GMCMDClk AF03 GMCTxEr *
AE04 GMCGTxClk * AF04 GMCCrS *
AE05 GMCRxDV * AF05 GMCRxEr *
AE06 GMCRxD7 * AF06 GMCRxD6 *
AE07 EAGND AF07 GMCRxD5 *
AE08 EAVDD AF08 GND
AE09 GMCRxD4 * AF09 GMCRxD3 *
AE10 GMCRxD1 * AF10 MemData26
AE11 MemData31 AF11 MemData30
AE12 DQS3 AF12 MemData25
AE13 MemData24 AF13 MemData29
AE14 MemData28 AF14 GND
AE15 MemData18 AF15 MemData19
AE16 DQS2 AF16 MemData22
AE17 MemData16 AF17 MemData17
AE18 MemODT1 AF18 MemData20
AE19 WE AF19 GND
AE20 BankSel1 AF20 CAS
AE21 MemAddr00 AF21 BankSel0
AE22 MemAddr03 AF22 MemAddr02
AE23 MemAddr07 AF23 MemAddr04
AE24 BA2 AF24 BA1
AE25 GND AF25 MemFBR
AE26 MemAddr08 AF26 GND
Table 4. Signals Listed by Ball Assignment (Sheet 7 of 7)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
PPC405EX – PowerPC 405EX Embedded Processor
38 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Pin Group List
The following table provides a summary of the number of package pins (balls) associated with each functional
interface group.
In the table “Signal Functional Description” on page 39, each external signal is listed along with a short description
of the signal function. Active-low signals (for example, Halt) are marked with an overline. See the preceding table,
“Signals Listed Alphabetically” on page 18, for the pin (ball) number to which each signal is assigned.
Shared Pins
Some signals are shared on the same package pin so that the pin can be used for different functions. In most
cases, the signal names shown in this table are not accompanied by signal names that might share the same pin.
If you need to know what, if any, signals are shared with a particular signal, look up the name in “Signals Listed
Alphabetically” on page 18. It is expected that in any single application a particular pin will always be programmed
to serve the same function. The flexibility of sharing allows a single chip to offer a richer pin selection than would
otherwise be possible.
Initialization Strapping
One group of pins is used as strapped inputs during system reset. These pins function as strapped inputs only
during reset and are used for other functions during normal operation (see “Initialization” on page 71). Note that the
use of these pins for strapping is not considered multiplexing since the strapping function is not programmable.
Pull-Up and Pull-Down Resistors
Pull-up and pull-down resistors are used for strapping during reset and to retain unused or undriven inputs in an
appropriate state. The recommended pull-up value of 3kΩ to +3.3V and pull-down value of 1kΩ to GND, applies
only to individually terminated signals. To prevent possible damage to the device, I/Os capable of becoming
outputs must never be tied together and terminated through a common resistor.
If your system-level test methodology permits, input-only signals can be connected together and terminated
through either a common resistor or directly to +3.3V or GND. When a resistor is used, its value must ensure that
the grouped I/Os reach a valid logical zero or logical one state when accounting for the total input current into the
PPC405EX.
Table 5. Pin Groups
Group No. of Pins
Total Signal Pins 246
VDD 17
OVDD 20
EOVDD 6
SVDD 10
GND 71
AVDD 7
AHVDD 2
SAVDD 1
SAGND 1
EAVDD 1
EAGND 1
AGND 4
Total Power Pins 141
Reserved 1
Total Pins 388
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 39
Data Sheet
Signal Functional Descriptions
The following table provides a description of the I/O signals on the PPC405EX.
Table 6. Signal Functional Description (Sheet 1 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
Ethernet Interface
GMCCD,
GMC1RxClk
GMII/MII: Collision detect.
RGMII 1: Receive clock. I3.3V tolerant
2.5V CMOS 1, 5
GMCCrS,
GMC1TxClk
GMII/MII: Carrier sense.
RGMII 1: Transmit clock. I/O 3.3V tolerant
2.5V CMOS 1
GMCGTxClk,
GMC0TxClk
GMII/MII: Transmit clock for GMII 1000Mbps.
RGMII 0: Transmit clock. O3.3V tolerant
2.5V CMOS
GMCMDClk Management data clock. O 3.3V tolerant
2.5V CMOS
GMCMDIO Management data I/O. I/O 3.3V tolerant
2.5V CMOS
GMCRefClk GMII/MII, RGMII: Required 125MHz reference clock. I
3.3V tolerant
2.5V CMOS
receiver
1, 5
GMCRxClk,
GMC0RxClk
GMII/MII: Receive clock.
RGMII 0: Receive clock. I3.3V tolerant
2.5V CMOS 1, 5
GMCRxD0:3,
GMC0RxD0:3
GMII/MII: Receive data.
RGMII 0: Receive data. I3.3V tolerant
2.5V CMOS 1
GMCRxD4:7,
GMC1RxD0:3
GMII/MII: Receive data.
RGMII 1: Receive data. I3.3V tolerant
2.5V CMOS 1
GMCRxDV,
GMC0RxCtl
GMII/MII: Receive data valid.
RGMII 0: Receive control. I3.3V tolerant
2.5V CMOS 1
GMCRxEr,
GMC1RxCtl
GMII/MII: Receive error.
RGMII 1: Receive control. I3.3V tolerant
2.5V CMOS 1
GMCTxClk GMII/MII: Transmit clock for 10/100Mbps. I 3.3V tolerant
2.5V CMOS 1, 5
GMCTxD0:3,
GMC0TxD0:3
GMII/MII: Transmit data.
RGMII 0: Transmit data. O3.3V tolerant
2.5V CMOS
GMCTxD4:7,
GMC1TxD0:3
GMII/MII: Transmit data.
RGMII 1: Transmit data. O3.3V tolerant
2.5V CMOS
GMCTxEn,
GMC0TxCtl
GMII/MII: Transmit enable.
RGMII 0: Transmit control. O3.3V tolerant
2.5V CMOS
GMCTxEr,
GMC1TxCtl
GMII/MII: Transmit error.
RGMII 1: Transmit control. O3.3V tolerant
2.5V CMOS
IIC Interface
IIC0SClk IIC Serial Clock. I/O 3.3V LVTTL 1, 2
IIC0SData IIC Serial Data. I/O 3.3V LVTTL 2
IIC1SClk IIC Serial Clock. I/O 3.3V LVTTL 1
IIC1SData IIC Serial Data. I/O 3.3V LVTTL 1
PPC405EX – PowerPC 405EX Embedded Processor
40 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
PCI Express Interface (n = 0 and 1)
PCIEnATB Analog Test Bus for manufacturing test. na Analog
PCIEnClkC
PCIEnClkT Differential input for external reference clock. I CML 5
PCIEnRExt
PCIEnRExtG
External reference resistor. Attach a 1.37 kΩ, 1% resistor between
RExt and RExtG to provide the reference for both the bias currents
and the impedance calibration circuitry.
na Analog
PCIEnRx
PCIEnRx
Differential receiver for received serial data.
Note: Input must be DC coupled and biased to 0V common mode. I LVDS receiver
PCIEnTx
PCIEnTx
Differential driver for transmitted serial data.
Note: Output must be AC coupled. O LVDS driver
Interrupts Interface
IRQ0:2 External interrupt requests. I 3.3V LVTTL
IRQ3:5 External interrupt requests. I 3.3V LVTTL 1
IRQ6 External interrupt requests. I 3.3V LVTTL
IRQ7:9 External interrupt requests. I 3.3V LVTTL 1
JTAG Interface
TCK Test clock. I 3.3V LVTTL 1
TDI Test data in. I 3.3V LVTTL
w/pull-up 1, 4
TDO Test data out. O 3.3V LVTTL
TMS Test mode select. I 3.3V LVTTL
w/pull-up 1
TRST Test reset. Must be low during power-on reset to initialize the JTAG
controller and for normal operation of the chip. I3.3V LVTTL
w/pull-up 1, 5
Table 6. Signal Functional Description (Sheet 2 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 41
Data Sheet
System Interface
SysClk System input clock. I
3.3V tolerant
2.5V CMOS
receiver
1
SysErr Machine check exception has occurred. O 3.3V tolerant
2.5V CMOS
SysReset Main system reset. This signal may be driven by the PPC405EX to
cause a board level reset to occur. I/O 3.3V tolerant
2.5V CMOS 1, 2
TestEn Test enable. Reserved for manufacturing LSSD test. I
3.3V LVTTL
receiver
w/pull-down
3
Halt External request to stop the processor. I
3.3V LVTTL
receiver
w/pull-up
TmrClk Processor timer external input. I
3.3V LVTTL
receiver
w/pull-up
GPIO00:27
GPIO29:31
General purpose I/O. Most of the GPIO signals are multiplexed with
other signals. Which signal is connected to the external pin depends
on the setting of bits in the GPIO registers.
I/O 3.3V LVTTL
GPIO28
General purpose I/O. Most of the GPIO signals are multiplexed with
other signals. Which signal is connected to the external pin depends
on the setting of bits in the GPIO registers.
I/O 3.3V tolerant
2.5V CMOS
PSROUser Performance screen ring output. Use for module characterization and
screening only. O3
Trace Interface
TrcClk Trace interface clock. Operates at half the CPU core frequency. O 3.3V LVTTL
TS0E
TS1E Even trace execution status. I/O 3.3V LVTTL
TS0O
TS1O Odd trace execution status. I/O 3.3V LVTTL
TS0:3 Trace status. I/O 3.3V LVTTL
Table 6. Signal Functional Description (Sheet 3 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
PPC405EX – PowerPC 405EX Embedded Processor
42 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
External Peripheral Interface
PerAddr05:31 Address bus 5:31. I/O 3.3V LVTTL
PerClk Clock output. O 3.3V LVTTL
PerCS0 Chip selects 0. O 3.3V LVTTL 2
PerCS1:3 Chip selects 1:3. I/O 3.3V LVTTL 1, 2
PerData00:31 Data bus 0:31. I/O 3.3V LVTTL
PerDataPar0:3 Data bus parity 0:3. I/O 3.3V LVTTL
PerOE Output enable. O 3.3V LVTTL 2
PerReady Slave is ready to transfer data. I 3.3V LVTTL
receiver
PerBLast Last transfer of burst access. I/O 3.3V LVTTL 1, 4
PerErr External bus error. I/O 3.3V LVTTL 1, 3
PerRW Read/Write. I/O 3.3V LVTTL 1, 2
PerWBE0:3 Write Byte enable 0:3. I/O 3.3V LVTTL 1, 2
ExtReset External reset. O 3.3V LVTTL
External Bus Master Interface
BusReq External bus request. O 3.3V LVTTL 1
ExtAck External data transfer complete. O 3.3V LVTTL 1
ExtReq External data transfer request. I 3.3V LVTTL 1
HoldReq External request for bus access. I 3.3V LVTTL 1
HoldAck External request acknowledge. O 3.3V LVTTL 1
DMA Interface
DMAAck0:1 External peripheral DMA acknowledge. O 3.3V LVTTL
DMAAck2:3 External peripheral DMA acknowledge. O 3.3V LVTTL 1
DMAReq0:1 External peripheral DMA request. I 3.3V LVTTL
DMAReq2 External peripheral DMA request. I 3.3V LVTTL 1
DMAReq3 External peripheral DMA request. I 3.3V LVTTL
DMAEOT0:1 External DMA peripheral end-of-transmission. I/O 3.3V LVTTL
DMAEOT2:3 External DMA peripheral end-of-transmission. I/O 3.3V LVTTL 1
Table 6. Signal Functional Description (Sheet 4 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 43
Data Sheet
NAND Flash Interface
NFALE Address latch enable. O 3.3V LVTTL
NFCE0 Chip select 0. O 3.3V LVTTL
NFCE1:3 Chip selects 1:3. O 3.3V LVTTL 1
NFCLE Command latch enable. O 3.3V LVTTL
NFData00:15 Data Bus I/O 3.3V LVTTL
NFRdyBusy Read/Busy. If low, indicates that Read/Erase command is in process.
If high, indicates that the command is complete. I 3.3V LVTTL
NFRE Read enable. O 3.3V LVTTL
NFWE Write enable. O 3.3V LVTTL
DDR1/2 SDRAM Interface
MemData00:31 Memory data. I/O 2.5V (1.8V)
SSTL2 Dr/Rcv
MemAddr00:14 Memory address. O 2.5V (1.8V)
SSTL2 Dr/Rcv
RAS Row address strobe. O 2.5V (1.8V)
SSTL2 Dr/Rcv
CAS Column address strobe. O 2.5V (1.8V)
SSTL2 Dr/Rcv
MemClkEn Clock enable. O 2.5V (1.8V)
SSTL2 Dr/Rcv
MemClkOut0
MemClkOut0 Differential DDR SDRAM clock output. O 2.5V (1.8V)
SSTL2 Dr/Rcv
MemFBD Feedback driver. Connect directly to MemFBR with the minimum
trace length. O2.5V (1.8V)
SSTL2 Dr/Rcv
MemFBR Feedback receiver. Connect externally to MemFBD. I 2.5V (1.8V)
SSTL2 Dr/Rcv
MemODT0:1 On-die termination. O 2.5V (1.8V)
SSTL2 Dr/Rcv
DM0:4 Write data byte lane mask. DM4 is the byte lane mask for the ECC
byte lane. O2.5V (1.8V)
SSTL2 Dr/Rcv
DQS0:4 Byte lane strobe. DQS4 is the strobe for the ECC lane. I/O 2.5V (1.8V)
SSTL2 Dr/Rcv
BA0:2 Bank address for up to eight banks. O 2.5V (1.8V)
SSTL2 Dr/Rcv
BankSel0:1 Bank select for up to two SDRAM memory banks. O 2.5V (1.8V)
SSTL2 Dr/Rcv
ECC0:7 ECC check bit byte. I/O 2.5V (1.8V)
SSTL2 Dr/Rcv
WE Write enable. O 2.5V (1.8V)
SSTL2 Dr/Rcv
Table 6. Signal Functional Description (Sheet 5 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
PPC405EX – PowerPC 405EX Embedded Processor
44 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
SVREF1A:B
SVREF2A:B
DDR 1 (DDR2) Reference voltage 1 and 2 inputs:
Minimum +1.15 (+0.825)V
Nomimal +1.25 (+0.9)V
Maximum +1.35 (0.975)V
I1.25V (0.9V)
Volt ref receiver
Serial Communication Port (SCP) Interface
SCPClkOut Output clock. I/O 3.3V LVTTL
SCPDI Data input. I 3.3V LVTTL
SCPDO Data output. O 3.3V LVTTL
UART Peripheral Interface
The UART interface can be configured as follows:
1. One 8-pin
2. Two 4-pin
3. Two 2-pin (pull up DCD, DSR, CTS and RTS)
4. One 4-pin and one 2-pin
UARTSerClk Serial clock input. I
3.3V LVTTL
receiver
w/pull-up
UARTnCTS Clear to send. I 3.3V LVTTL 1, 6
UARTnDCD Data carrier detect. I 3.3V LVTTL 1, 6
UARTnDSR Data set ready. I 3.3V LVTTL 1, 6
UARTnDTR Data terminal ready. O 3.3V LVTTL 1
UARTnRI Ring indicator. I 3.3V LVTTL 1
UARTnRTS Request to send. O 3.3V LVTTL 1
UARTnRx Receive data. I 3.3V LVTTL
UARTnTx Transmit data. O 3.3V LVTTL
USB 2.0 Interface
USB2Clk USB clock. I 3.3V LVTTL
receiver 5
USB2Data0:7 Parallel data bus. I/O 3.3V LVTTL
USB2Dir Data bus direction control. I 3.3V LVTTL
USB2Next
Next data byte control. When data is being transferred to the PHY,
the next byte should be sent. When data is being received from the
PHY, the next byte is available.
I 3.3V LVTTL
USB2Stop Stop output control. O 3.3V LVTTL
Table 6. Signal Functional Description (Sheet 6 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 45
Data Sheet
Power
VDD Logic Supply (+1.2V). na na na
OVDD I/O Supply (+3.3V). na na na
SVDD DDR1/2 SDRAM Supply (+2.5 V or +1.8V) na na na
EOVDD Ethernet I/O Supply (+2.5V) na na na
GND Ground. na na na
SAVDD System PLL Analog Supply (+2.5V). na na na
SAGND System PLL Analog Ground. na na na
EAVDD Ethernet PLL Analog Supply (+2.5V). na na na
EAGND Ethernet PLL Analog Ground. na na na
AVDD PCI-Express SerDes Analog Supply (+1.2V) na na na
AHVDD PCI-Express SerDes PLL Analog Supply (+2.5V). na na na
AGND PCI-Express Analog Ground (for AHVDD and AVDD).na na na
Other
Reserved Do not connect voltages, grounds, or signals to these pins. na na na
Table 6. Signal Functional Description (Sheet 7 of 7)
Notes:
1. Receiver input has hysteresis.
2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 38 for recommended termination values.
4. If not used, must pull up.
5. If not used, must pull down.
6. Strapping input during reset; pull up or pull down as required.
Signal Name Description I/O Type Notes
PPC405EX – PowerPC 405EX Embedded Processor
46 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Ratings and Specifications
Table 7. Absolute Maximum Ratings
The absolute maximum ratings below are stress ratings only. Operation at or beyond these maximum ratings can cause
permanent damage to the device. None of the performance specification contained in this document are guaranteed when
operating at these maximum ratings.
Characteristic Symbol Value Unit Notes
Logic Supply Voltage (internal logic) VDD 0 to +1.6 V
PCI-Express SerDes Analog Supply Voltage AVDD 0 to +1.6 V 1
PCI-Express SerDes PLL Analog Supply Voltage AHVDD 0 to +2.6 V 1
I/O Supply Voltage OVDD 0 to +3.6 V
SDRAM DDR1[2] Supply Voltage SVDD 0 to +2.6 [+1.9] V
Ethernet I/O Supply Voltage EOVDD 0 to +2.6 V
System PLL Analog Supply Voltage SAVDD 0 to +2.6 V 1
Ethernet PLL Analog Supply Voltage EAVDD 0 to +2.6 V 1
Input voltage (3.3V LVTTL receivers) VIN 0 to +3.6 V
Storage Temperature Range TSTG −55 to +150 °C
Case Temperature Range under bias TC−40 to +120 °C
Junction Temperature Range TJMax −40 to +125 °C2
Notes:
1. The analog voltages can be derived from the +1.2V and +2.5V supplies, but must be filtered as shown below before entering the
PPC405EX. Use a separate filter for each voltage. This circuit can be used for AVDD, AHVDD , SAVDD, and EAVDD. Use AGND
with AVDD and AHVDD. Use SAGND with SAVDD. Use EAGND with EAVDD. These analog grounds must be brought out and
connected to the digital ground plane at the filter capacitor. Keep all wire lengths as short as possible.
2. The device meets all electrical specifications at a junction temperature, under bias, of 125ºC, but part lifetime and reliability is
reduced. It is recommended that prudent thermal management techniques be used to maximize device lifetime.
VDD
C1
AVDD
L1 L1 – Murata BLM18AG121SN1D
C1 – 0.1 μF ceramic
AGND
GND
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 47
Data Sheet
Thermal Management
The following heat sink was used in the above thermal analysis:
26.92mm x 27mm x 11.43mm
The heat sink is manufactured by:
Aavid Thermalloy, P/N 62925
Table 8. Package Thermal Specifications
The PPC405EX is designed to operate within a case temperature range TC defined in “Recommended DC Operating
Conditions” on page 48. Thermal resistance values for the EPBGA packages in a convection environment are as follows:
Parameter Symbol
Airflow
ft/min (m/sec) Unit
0 (0) 100 (0.51) 200 (1.02) 300 (1.52) 400 (2.02) 500 (2.53) 600 (3.03)
Junction-to-ambient
thermal resistance
without heat sink
θJA 18.9 16.6 15.8 15.4 15.0 14.7 14.4 °C/W
Junction-to-ambient
thermal resistance
with heat sink
θJA 15.5 12.5 11.4 10.9 10.7 10.5 10.3 °C/W
Resistance Value
Junction-to-case thermal
resistance θJC 8.96 °C/W
Junction-to-board thermal
resistance θJB 13.74 °C/W
Notes:
1. Values in the table are achieved with the following JEDEC standard board: 114.5mm x 101.6mm x 1.6mm, 4 layers.
2. For a chip mounted on a card with at least one signal and two power planes, the following relationships exist:
a. Case temperature, TC, is measured at top center of case surface with device soldered to circuit board.
b. TA = TC – PxθCA, where TA is ambient temperature and P is power consumption.
c. TCMax = TJMax – PxθJC, where TJMax is maximum junction temperature and P is power consumption.
PPC405EX – PowerPC 405EX Embedded Processor
48 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table 9. Recommended DC Operating Conditions (Sheet 1 of 2)
Device operation beyond the conditions specified is not recommended. Extended operation beyond the recommended
conditions can affect device reliability.
Parameter Symbol Minimum Typical Maximum Unit Notes
Logic Supply Voltage—400MHz VDD +1.1 +1.15 +1.2 V 2
Logic Supply Voltage—533MHz & 600MHz VDD +1.2 +1.25 +1.3 V
I/O Supply Voltage OVDD +3.15 +3.3 +3.45 V
SDRAM DDR1[2] Supply Voltage SVDD +2.4 [+1.7] +2.5 [+1.8] +2.6 [+1.9] V
Ethernet I/O Supply Voltage EOVDD +2.4 +2.5 +2.6 V
PLL Analog Supply Voltage
AHVDD
SAVDD
EAVDD
+2.4 +2.5 +2.6 V
Analog Supply Voltage—400MHz AVDD +1.1 +1.15 +1.2 V 2
Analog Supply Voltage—533MHz & 600MHz AVDD +1.2 +1.25 +1.3 V
I/O Input Low (3.3V LVTTL) VIL 0+0.8V
I/O Input High (3.3V LVTTL) VIH +2.0 +3.6 V
I/O Output Low (3.3V LVTTL) VOL 0+0.4V
I/O Output High (3.3V LVTTL) VOH +2.4 +3.6 V
I/O Input Low (3.3V tol, 2.5V CMOS) VIL 0+0.7V
I/O Input High (3.3V tol, 2.5V CMOS) VIH +1.7 +3.6 V
I/O Output Low (3.3V tol, 2.5V CMOS) VOL 0+0.4V
I/O Output High (3.3V tol, 2.5V CMOS) VOH +2.0 +2.7 V
I/O Input Low DDR1[2] (SSTL2) VIL − 0.3 SVREF − 0.18
[0.125] V
I/O Input High DDR1[2] (SSTL2) VIH
SVREF + 0.18
[0.125] SVDD + 0.3 V
I/O Output Low DDR1[2] (SSTL2) VOL See JESD8-9 (JESD8-15A) standard. V
I/O Output High DDR1[2] (SSTL2) VOH See JESD8-9 (JESD8-15A) standard. V
Input Leakage Current
(no pull-up or pull-down) IIL1 01
μA
Input Leakage Current
(with internal pull-down) IIL2 0 (LPDL) 200 (MPUL) μA1
Input Leakage Current
(with internal pull-up) IIL3 −150 (LPDL) 0 (MPUL) μA1
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 49
Data Sheet
Power Supply Sequence
All the PPC405EX I/O designs are power supply sequence independent. There is no requirement that the power
supplies power up in any particular order. The following items are power sequence considerations:
• If the logic power (VDD) is applied before the I/O supply voltages, the I/Os include internal supply sequencing
circuitry that ensures the output of the receiver connected to internal chip logic is 0 until the I/O power is
applied. When the logic power supply is on and the I/O power supplies are off, the I/O logic connected to the
associated ball neither sinks or sources significant current unless influenced by an internal pull-up or pull-down
resistor. While the I/O supply is ramping, the state of the I/O balls are not predictable. This power sequence is
not destructive to the I/Os or internal logic and does not cause any functional problems.
• If the I/O power is applied before the logic power is applied, the output driver output stage (connected to the
balls) will come up in an unknown state (driving 1, driving 0, or tri-state) until the internal logic voltage is stable
within normal operating range. This power sequence is not destructive to the I/Os or internal logic and does not
cause any functional problems.
• External voltage should not be applied to the chip I/O balls before the associated I/O power supply voltage is
applied to the chip.
• A chip power down cycle must complete (all I/O supply voltages and VDD are below +0.4V) before a new
power-up cycle is started.
• During a 405EX power-up cycle, the system reset and test reset inputs should be asserted low. System reset
and test reset should remain asserted until the system clock is stable and then at least 32 system clock times
after all power supplies are stable within normal operating range. Failure to follow this reset sequence during
the power-up cycle might result in unpredictable operation.
I/O Maximum Allowable Overshoot
(3.3V LVTTL and 2.5V/3.3 tolerant CMOS) VMAO +3.9 V 3, 4
I/O Maximum Allowable Undershoot
(3.3V LVTTL and 2.5V/3.3 tolerant CMOS) VMAU −0.6 0 V 3, 4
Case Temperature TC−40 +85 °C5
Notes:
1. LPDL is least positive down level; MPUL is most positive up level.
2. Can be extended to 1.1V min., 1.2V typ., 1.3V max. with an estimated power increase of 130mW at 1.2V nom.
3. Maximum duration is 10% of the bus clock period. Bus clock is as follows:
EBC—PerClk
Ethernet—RxClk
USB—USB2Clk
4. Duration of the overshoot is time above VIH max. Duration of the undershoot is time below VIL min.
5. A 533MHz part running at 400MHz or less can operate up to a case temperature of +95°C.
Table 9. Recommended DC Operating Conditions (Sheet 2 of 2)
Device operation beyond the conditions specified is not recommended. Extended operation beyond the recommended
conditions can affect device reliability.
Parameter Symbol Minimum Typical Maximum Unit Notes
PPC405EX – PowerPC 405EX Embedded Processor
50 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table 10. I/O Input Capacitance
Parameter Symbol Maximum Unit Notes
3.3V LVTTL CIN1 2.3 pF
2.5V CMOS CIN2 2.1 pF
2.5/1.8V SSTL2 CIN3 3.2 pF
PCI Express differential data receiver CIN4 1.59 pF
PCI Express differential data transmitter CIN5 1.16 pF
PCI Express differential clock receiver CIN6 0.188 pF
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 51
Data Sheet
Table 11. Typical DC Power Supply Requirements with DDR1 SDRAM
Frequency
(MHz)
+1.2V nom (VDD+AVDD)+1.8V
(not used
with DDR1)
+2.5V
(SVDD+EOVDD+
AHVDD+SAVDD+EAVDD)
+3.3V
(OVDD)Total Unit Notes
+1.15V +1.25V
333 1.08 na na 0.54 0.11 1.73 W 1, 2
400 1.20 na na 0.60 0.11 1.91 W 1, 3
533 na 1.57 na 0.60 0.11 2.28 W 1, 4
600 na 1.60 na 0.60 0.12 2.32 W 1, 5
Notes:
1. Typical power is measured on a typical process part at a case temperature of +85°C at the specified voltages while running Linux and
test applications that exercise each function with representative traffic (2 PCI Express, 2 Gigabit Ethernet, USB, and Security).
2. DDR1 running at 333MHz., PLB running at 166MHz.
3. DDR1 running at 400MHz., PLB running at 200MHz.
4. DDR1 running at 355MHz., PLB running at 177MHz.
5. DDR1 running at 400MHz., PLB running at 200MHz.
Table 12. Maximum DC Power Supply Requirements with DDR1 SDRAM
Frequency
(MHz)
+1.2V nom (VDD+AVDD)+1.8V
(not used
with DDR1)
+2.6V
(SVDD+EOVDD+
AHVDD+SAVDD+EAVDD)
+3.45V
(OVDD)Total Unit Notes
+1.2V +1.3V
333 2.06 na na 0.65 0.15 2.86 W 1, 2
400 2.24 na na 0.72 0.15 3.11 W 1, 3
533 na 3.00 na 0.73 0.17 3.90 W 1, 4
600 na 3.23 na 0.75 0.17 4.15 W 1, 5
Notes:
1. Maximum power is measured on a best-case process (worst-case power) part at a case temperature of +85°C at the specified voltages
while running Linux and test applications that exercise each function with representative traffic (2 PCI Express, 2 Gigabit Ethernet,
USB, and Security).
2. DDR1 running at 333MHz., PLB running at 166MHz.
3. DDR1 running at 400MHz., PLB running at 200MHz.
4. DDR1 running at 355MHz., PLB running at 177MHz.
5. DDR1 running at 400MHz., PLB running at 200MHz.
PPC405EX – PowerPC 405EX Embedded Processor
52 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table 13. Typical DC Power Supply Requirements with DDR2 SDRAM
Frequency
(MHz)
+1.2V nom (VDD+AVDD)+1.8V
(SVDD)
+2.5V
(EOVDD+AHVDD+
SAVDD+EAVDD)
+3.3V
(OVDD)Total Unit Notes
+1.15V +1.25V
333 1.08 na 0.21 0.23] 0.10 1.62 W 1, 2
400 1.20 na 0.26 0.23 0.10 1.79 W 1, 3
533 na 1.57 0.2 0.24 0.11 2.13 W 1, 4
600 na 1.60 0.26 0.25 0.12 2.23 W 1, 5
Notes:
1. Typical power is measured on a typical process part at a case temperature of +85°C at the specified voltages while running Linux and
test applications that exercise each function with representative traffic (2 PCI Express, 2 Gigabit Ethernet, USB, and Security).
2. DDR2 running at 333MHz., PLB running at 166MHz.
3. DDR2 running at 400MHz., PLB running at 200MHz.
4. DDR2 running at 355MHz., PLB running at 177MHz.
5. DDR2 running at 400MHz., PLB running at 200MHz.
Table 14. Maximum DC Power Supply Requirements with DDR2 SDRAM
Frequency
(MHz)
+1.2V nom (VDD+AVDD)+1.9V
(SVDD)
+2.6V
(EOVDD+AHVDD+
SAVDD+EAVDD)
+3.45V
(OVDD)Total Unit Notes
+1.2V +1.3V
333 2.06 na 0.21 0.26 0.15 2.68 W 1, 2
400 2.24 na 0.22 0.26 0.15 2.87 W 1, 3
533 na 3.00 0.23 0.26 0.17 3.66 W 1, 4
600 na 3.22 0.30 0.28 0.17 3.97 W 1, 5
Notes:
1. Maximum power is measured on a best-case process (worst-case power) part at a case temperature of +85°C at the specified voltages
while running Linux and test applications that exercise each function with representative traffic (2 PCI Express, 2 Gigabit Ethernet, USB,
and Security).
2. DDR2 running at 333MHz., PLB running at 166MHz.
3. DDR2 running at 400MHz., PLB running at 200MHz.
4. DDR2 running at 355MHz., PLB running at 177MHz.
5. DDR2 running at 400MHz., PLB running at 200MHz.
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 53
Data Sheet
Table 15. DC Power Supply Loads with DDR1 SDRAM
Parameter Symbol Typical Maximum Unit Notes
VDD (+1.2V) active operating current IDD1.2 1280 2475 mA 1
AVDD (+1.2V) active operating current IADD 410mA1
AHVDD (+2.5V) active operating current IAHDD 12mA1
OVDD (+3.3V) active operating current IODD 35 50 mA 1
SVDD + EOVDD (+2.5V) active operating current IDD 235 280 mA 1
SAVDD (+2.5V) active operating current ISADD 12mA1
EAVDD (+2.5V) active operating current IEADD 12mA1
Notes:
1. The maximum current values listed above are not guaranteed to be the highest obtainable. These values are dependent on many
factors including the type of applications running, clock rates, use of internal functional capabilities, external interface usage, case
temperature, and the power supply voltages. Your specific application can produce significantly different results. VDD (logic) current and
power are primarily dependent on the applications running and the use of internal chip functions (DMA, PCI Express, Ethernet, and so
on). OVDD (I/O) current and power are primarily dependent on the capacitive loading, frequency, and utilization of the external buses.
The information in this table provides details about the conditions under which the listed values were obtained. Maximum power is
measured on a best-case process (worst-case power) part running at 600MHz with a case temperature of +85°C and with voltages of
VDD = +1.30V, OVDD = +3.45V, SVDD = +2.6V, and EOVDD = +2.6V while running Linux and test applications that exercise each
function with representative traffic (2 PCI Express, 2 Gigabit Ethernet, USB, Security).
Table 16. DC Power Supply Loads with DDR2 SDRAM
Parameter Symbol Typical Maximum Unit Notes
VDD (+1.2V) active operating current IDD 1280 2475 mA 1
AVDD (+1.2V) active operating current IADD 410mA1
AHVDD (+2.5V) active operating current IAHDD 12mA1
OVDD (+3.3V) active operating current IODD 35 50 mA 1
SVDD (+1.8V) active operating current ISDD 145 155 mA 1
EOVDD (+2.5V) active operating current IEODD 95 100 mA 1
SAVDD (+2.5V) active operating current ISADD 12mA1
EAVDD (+2.5V) active operating current IEADD 12mA1
Notes:
1. The maximum current values listed above are not guaranteed to be the highest obtainable. These values are dependent on many
factors including the type of applications running, clock rates, use of internal functional capabilities, external interface usage, case
temperature, and the power supply voltages. Your specific application can produce significantly different results. VDD (logic) current and
power are primarily dependent on the applications running and the use of internal chip functions (DMA, PCI Express, Ethernet, and so
on). OVDD (I/O) current and power are primarily dependent on the capacitive loading, frequency, and utilization of the external buses.
The information in this table provides details about the conditions under which the listed values were obtained. Maximum power is
measured on a best-case process (worst-case power) part running at 600MHz with a case temperature of +85°C and with voltages of
VDD = +1.30V, OVDD = +3.45V, SVDD = +1.9V, and EOVDD = +2.6V while running Linux and test applications that exercise each
function with representative traffic (2 PCI Express, 2 Gigabit Ethernet, USB, Security).
PPC405EX – PowerPC 405EX Embedded Processor
54 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Power Control
This chip has power management control to put the following functional units to sleep if not needed. The typical
and maximum power consumption for the each of these units is:
Test Conditions
Clock timing and switching characteristics are specified in accordance with minimum
operating conditions shown in the table “Recommended DC Operating Conditions” on
page 48. For all signals, AC specifications are characterized at TC = +85°C with the test
load shown in the figure to the right.
Note 1: In order to support 1Gbps Ethernet data rate, the minimum OPB clock frequency is 66.66Mhz. If an application is
limited to 100Mbps, the minimum OPB clock frequency is 33.33Mhz.
Table 17. Power Contribution of Functional Units
Functional Unit Typical Maximum Units Notes
EBM/OPB 0.006 0.012 W
Security 0.117 0.230 W
Nand Flash 0.127 0.246 W
USB 0.005 0.008 W
EMAC 0.118 0.133 W
Table 18. System Clocking Specifications
Symbol Parameter Minimum Maximum Units
CPU
PFCProcessor clock frequency (must be ≥ SCFC)333.33 600 MHz
SysClk Input
SCFCFrequency 33.33 100 MHz
SCTCS Edge stability (phase jitter, cycle-to-cycle) na ±0.1 ns
SCTCH High time (% of nominal period) 40 60 %
SCTCL Low time (% of nominal period) 40 60 %
SCRT Rise time na 1 ns
Other Clocks
VCOFCVCO frequency 600 1800 MHz
PLBFCPLB and MemClkOut0 frequency 133 200 MHz
OPBFCOPB frequency 661100 MHz
AHBFc AHB frequency 60 100 MHz
Output
Pin 10pF
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 55
Data Sheet
Figure 3. Clocking Waveform
Spread Spectrum Clocking
Care must be taken if using a spread spectrum clock generator (SSCG) with the PPC405EX. This controller uses a
PLL for clock generation inside the chip. The accuracy with which the PLL follows the SSCG is called tracking
skew. The PLL bandwidth and phase angle determine how much tracking skew exists between the SSCG and the
PLL for a given frequency deviation and modulation frequency. If using an SSCG with the PPC405EX the following
conditions must be met:
• The frequency deviation must not violate the minimum clock cycle time. Therefore, when operating the
PPC405EX with one or more internal clocks at their maximum supported frequency, the SSCG can only lower
the frequency.
• The maximum frequency deviation must not exceed −3%, and the modulation frequency must not exceed
40kHz. In some cases, on-board PPC405EX peripherals impose more stringent requirements (see Note 1).
• Use the peripheral bus clock for logic that is synchronous to the peripheral bus because this clock tracks the
modulation.
Notes:
1. The serial port baud rates are synchronous to the modulated clock. The serial port has a tolerance of
approximately 1.5% on baud rate before framing errors begin to occur, assuming that the connected device is
running at precise baud rates. If an external serial clock is used, baud rate is unaffected by the modulation.
2. Ethernet operation is unaffected.
3. IIC operation is unaffected.
4. For PCI-E see the PCI Express I/O Specifications.
Caution: The system designer must ensure that any SSCG used with the PPC405EX meets these requirements
and does not adversely affect other aspects of the system.
TCL
TCH
TC
1.7 (2.0) V
1.25 (1.5) V
0.7 (0.8) V
Note: SysClk and GMCRefClk are 2.5V (3.3V tolerant) signals. Rise time should be measured between 0.7V and 1.7V.
PPC405EX – PowerPC 405EX Embedded Processor
56 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table 19. Peripheral Interface I/O Clock Timings (not SDRAM or PCI-E)
Clock Minimum Maximum Units Notes
GMCTxClk frequency 125 125 MHz
GMCTxClk high time 45% of nominal – ns
GMCTxClk low time 55% of nominal – ns
GMCRxClk frequency 125 125 MHz
GMCRxClk high time 45% of nominal – ns
GMCRxClk low time 55% of nominal – ns
GMCGTxClk 125 125 MHz
GMCMDClk 2.5 25 MHz
GMCRefClk 125 125 MHz
GMCRefClk edge stability (phase jitter, cycle-to-cycle) na ± 0.1 ns
GMCRefClk rise time na 1 ns
GMCRefClk high time 40% of nominal – ns
GMCRefClk low time 60% of nominal – ns
GMCnRxClk 125 125 MHz
GMCnTxClk 125 125 MHz
UARTSerClk 1000 / 2TOPB + 2ns MHz 1
TmrClk na 100 MHz
PerClk 33 100 MHz
TCK na 40 MHz
USB2Clk (60MHz ± 0.05%) 57.97 60.03 MHz
TrcClk 66 300 MHz 2
Notes:
1. TOPB is the period in ns of the OPB clock. The internal OPB clock runs at an integral divisor ratio of the frequency of the PLB clock. The
maximum OPB clock frequency is 100MHz.
2. TrcClk is 1/2 CPU Clk. The maximum CPU Clk supported by instruction trace probes is 400 MHz.
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 57
Data Sheet
Figure 4. Input Setup and Hold Timing Waveform
Figure 5. Output Delay and Float Timing Waveform
Clock
TIS TIH
MIN MIN
Inputs
Valid
1.25 (1.5)V
1.25 (1.5)V
Valid
TOV TOH
MIN
Outputs
Clock
Outputs
TOF
MIN
MAX
MAX
1.25 (1.5)V
1.25 (1.5)V
1.25 (1.5)V
PPC405EX – PowerPC 405EX Embedded Processor
58 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Figure 6. Setup and Hold Timing Waveforms for RGMII Signals
Table 20. RGMII I/O Timing
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
TskewR
(min)
TskewR
(max)
TskewT
(min)
TskewT
(max)
I/O H
(min)
I/O L
(min)
GMCnRxClk – – – – n/a n/a –
GMCnRxD0:3 1.0 2.8 n/a n/a n/a n/a GMCnRxClk 1
GMCnRxCtl 1.0 2.8 n/a n/a n/a n/a GMCnRxClk 1
GMCnTxClk v – – – 5.51 7.23 –
GMCnTxD0:3 n/a n/a -0.5 0.5 5.51 7.23 GMCnTxClk
GMCnTxCtl n/a n/a -0.5 0.5 5.51 7.23 GMCnTxClk
Notes:
1. Assumes GMCnRxClk is delayed either on the board or by the PHY to ensure adequate timing margin.
GMCnTxClk
GMCnRxClk
GMCnTxD/Ctl Valid Valid
TskewT
GMCnRxD/Ctl Valid Valid
TskewR
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 59
Data Sheet
Table 21. I/O Specifications (Sheet 1 of 2)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
IOH
(min)
IOL
(min)
Ethernet GMII Interface
GMCMDClk na na na na 5.51 7.23
GMCMDIO 10 0 10 10 5.51 7.23 Async 1
GMCCD 2 0 na na Async 1
GMCCrS 2 0 na na Async 1
GMCRxD0:7 1.85 0 na na GMCRxClk 1
GMCRxDV 1.95 0 na na GMCRxClk 1
GMCRxEr 1.95 0 na na GMCRxClk 1
GMCTxD0:7 2.3 2.0 5.51 7.23 GMCGTxClk 1
GMCTxEr 2.4 2.0 5.51 7.23 GMCGTxClk 1
GMCTxEn 2.4 2.0 5.51 7.23 GMCGTxClk 1
Internal Peripheral Interfaces (not SDRAM or PCI-E)
IICnSData na 10.46
UARTnCTS na na 15.75 10.46
UARTnRTS na na 15.75 10.46
UARTnDSR na na 15.75 10.46
UARTnDCD na na 15.75 10.46
UARTnDTR na na 15.75 10.46
UARTnRI na na 15.75 10.46
UARTnRx na na na na
UARTnTx na na 15.75 10.46
SCPDI na na
SCPDO na 10.46
USB2Data0:7 3.9 0 6.3 2 15.75 10.46 USB2Clk
USB2Dir 3.7 0 6.4 2 na na USB2Clk
USB2Next 3.5 0 na na USB2Clk
USB2Stop 6.4 2 15.75 10.46 USB2Clk
DMA Interface
DMAAck0:3 5.2 1.0 15.75 10.46 PerClk
DMAReq0:3 2.4 1 na na PerClk
DMAEOT0:3 2 1 5.3 1.0 15.75 10.46 PerClk
Interrupts Interface
IRQ0:9 15.75 10.46
JTAG Interface
TDI 2 5.5 na na TCK
TDO 9.5 1 15.75 10.46 TCK
TMS 2 5.5 na na TCK
TRST na na Async
PPC405EX – PowerPC 405EX Embedded Processor
60 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
System Interface
GPIO00:10 na na na na 11.08 7.37
GPIO11:15 na na na na 5.51 7.23
GPIO16:27 na na na na 11.08 7.37
GPIO28 na na na na 15.75 10.46
GPIO29:31 na na na na 11.08 7.37
Halt na na na na na na
SysErr na na na na 5.51 7.23
SysReset na na na na 5.51 7.23
External Peripheral Interface
PerAddr05:31 1.8 1 5.3 1 11.08 7.37 PerClk
PerCS0:3 5.2 1 11.08 7.37 PerClk
PerData00:31 2.7 1 5.3 1 11.08 7.37 PerClk
PerDataPar0:3 1.9 1 5.3 1 11.08 7.37 PerClk
PerOE 5.2 1 11.08 7.37 PerClk
PerReady 2 1 na na PerClk
PerRW 1.8 1 5.3 1 11.08 7.37 PerClk
PerWBE0:3 1.7 1 5.1 1 11.08 7.37 PerClk
PerBLast 2 1 5 1 11.08 7.37 PerClk
PerErr 1.9 1 5.3 1 11.08 7.37 PerClk
ExtReset 5.3 1 11.08 7.37 PerClk
BusReq 2.3 1 5.1 1 11.08 7.37 PerClk
HoldReq 2 1 5.2 1 na na PerClk
HoldAck 5.2 1 11.08 7.37 PerClk
ExtAck 2.3 1 5 1 11.08 7.37 PerClk
ExtReq 2 1 5.3 na na PerClk
NFALE 5.3 1 11.08 7.37 PerClk
NFCE0:3 5.3 1 11.08 7.37 PerClk
NFCLE 5.3 1 11.08 7.37 PerClk
NFData0:15 2.3 1 5.3 1 11.08 7.37 PerClk
NFRdyBusy 1.7 1 na na PerClk
NFREn 5.3 1 11.08 7.37 PerClk
NFWEn 5.3 1 11.08 7.37 PerClk
Table 21. I/O Specifications (Sheet 2 of 2)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
IOH
(min)
IOL
(min)
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 61
Data Sheet
DDR 1/2 SDRAM I/O Specifications
The DDR SDRAM controller times its operation using the internal PLB clock signal and generates MemClkOut from
the PLB clock. The PLB clock is an internal signal that cannot be directly observed. However MemClkOut is the
same frequency as the PLB clock signal and is in phase with the PLB clock signal.
Note: MemClkOut can be advanced with respect to the PLB clock by means of the SDRAM0_CLKTR
programming register. In a typical system, users advance MemClkOut by 90°. This depends on the specific
application and requires a thorough understanding of the memory system in general (refer to the DDR
SDRAM Controller chapter in the PPC405EX Embedded Processor User’s Manual).
The signals are terminated as indicated in Figure 7 for the DDR timing data and output currents in the following
sections.
Figure 7. DDR SDRAM Simulation Signal Termination Model
DDR2 SDRAM On-Die Termination Impedance Setting
For all DDR2 applications, the On-Die Termination (ODT) impedance value must be set to 75Ω in the DIMM
Extended Mode Register (EMR) in order to optimize the data transmission during memory write operations.
10pF
10pF
MemClkOut0
MemClkOut0
120Ω
50
Ω
30pF
Addr/Ctrl/Data/DQS/DM (DDR1)
VTT = SOVDD/2
PPC405EX
Addr/Ctrl (DDR2)
Note: This diagram illustrates the model of the DDR SDRAM interface used when generating simulation timing data.
It is not a recommended physical circuit design for this interface. An actual interface design depends on many
factors, including the type of memory used and the board layout.
PPC405EX – PowerPC 405EX Embedded Processor
62 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
DDR SDRAM Write Operation
The rising edge of MemClkOut aligns with the first rising edge of the DQS signal on writes as indicated in Figure 8.
DQS rising and falling edges are centered on valid data for writes.
The data in Table 23 is generated by means of simulation and includes logic, driver, package RLC, and lengths.
Values are calculated over best case and worst case processes with speed, junction temperature, and voltage as
follows:
Note: In the following tables and timing diagrams, minimum values are measured under best case conditions and
maximum values are measured under worst case conditions. The timing numbers in the following sections are
obtained using a simulation that assumes a model as shown in Figure 7.
Table 22. DDR SDRAM Output Driver Specifications
Signal Path Output Current (mA)
I/O H (maximum) I/O L (maximum)
Write Data
MemData00:31 10 10
ECC0:7 10 10
DM0:4 10 10
MemClkOut0 10 10
MemAddr00:14 10 10
BA0:2 10 10
RAS 10 10
CAS 10 10
WE 10 10
BankSel0:1 10 10
MemClkEn 10 10
DQS0:4 10 10
MemODT0:1 10 10
Table 23. DDR SDRAM Write Operation Conditions
Case Process Speed Junction Temperature (°C) Voltage (V)
Best Fast −40 +1.3
Worst Slow +125 +1.1
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 63
Data Sheet
The following diagram illustrates the relationship among the signals involved with a DDR write operation.
Figure 8. DDR SDRAM Write Cycle Timing
Note: The timing data in the following tables is based on simulation runs using Einstimer.
Table 24. I/O Timing—DDR SDRAM TDS
Notes:
1. All of the DQS signals are referenced to MemClkOut0 with the DQS delay line programmed to 1 cycle.
2. Clock speed is 200MHz.
Signal Name TDS (ns)
Minimum Maximum
DQS0 4 6
DQS1 4 6
DQS2 4 6
DQS3 4 6
DQS4 4 6
DQS
MemData
PLB Clk
MemClkOut0
Addr/Cmd
TSA
THA
TDS
TDS
TSD
THD
TSD
THD
TSA = Setup time for address and command signals to MemClkOut0
THA = Hold time for address and command signals from MemClkOut0
TDS = Delay from rising/falling edge of clock to the rising/falling edge of DQS
TSD = Setup time for data signals (minimum time data is valid before rising/falling edge of DSQ)
THD = Hold time for data signals (minimum time data is valid after rising/falling edge of DSQ)
PPC405EX – PowerPC 405EX Embedded Processor
64 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
DDR SDRAM Read Operation
Data on a read is edge aligned with DQS. To capture the incoming data on the rising and falling edges, DQS is
delayed by the DDR controller in order to center a DQS edge on valid data. Programmable registers control the
delay.
DDR SDRAM MemClkOut0 and Read Clock Delay
In order to accommodate timing variations introduced by memory layout and process, a three-stage data path is
used to eliminate metastability and allow data sampling to be adjusted for minimum latency.
Figure 9 shows the data read path of a single data bit. Data entering on the left is captured in the Stage 1 Flip
Flops. Four Flip Flops are needed to capture an entire four beat burst on the DDR interface. The DDR controller
only supports burst of four. Data captured on the rising edge of DQS is stored in the even numbered Flip Flops.
Like wise, data captured on the falling edge of DQS is stored in the odd numbered Flips Flops.
To latch the data in Stage 1, a delayed version of DQS is used. Initialization software is responsible for tuning the
DQS delay timing so that DQS is centered on valid data. Since there is process variation between parts and
possible voltage variations on boards, read tuning is required. Fixed DQS delay values should not be used on
production systems.
The Feedback Data Capture Window selects which Flip Flop is used to store the data sampled by DQS. Each
output of this block generates a pulse to an input multiplexer. The series of four pulses selecting the input
multiplexer is initiated by a feedback signal pulse on the input of the Feedback Data Capture Window. The DDR
controller calculates when to assert the feedback signal based on when the data should be present after a read
command.
The width of the feedback pulse is the same as DDR 1X clock. The internal DDR 1X clock is the same frequency
as MemClkOut0. MemClkOut0 is slightly delayed relative to DDR 1X clock due to the insertion delay of the drivers.
Table 25. I/O Timing—DDR SDRAM TSA and THA
Signal Name TSA (ns) Minimum THA (ns) Minimum
MemAddr00:14 1.08 1.12
BA0:2 1.12 1.15
BankSel0:1 1.09 1.13
MemClkEn 1.10 1.16
CAS 1.10 1.13
RAS 1.09 1.12
WE 1.08 1.16
Table 26. I/O Timing—DDR SDRAM Write Timing TSD and THD
Notes:
1. TSD and THD are measured under worst case conditions.
2. Clock speed for the values in the table is 200MHz.
3. The time values in the table include 1/4 of a cycle at 200MHz (5ns x 0.25 = 1.25 ns).
4. To obtain adjusted TSD and THD values for lower clock frequencies, subtract 1.25 ns from the values in the table and add 1/4
of the cycle time for the lower clock frequency (for example, TSD − 1.25 + 0.25TCYC).
Signal Names Reference Signal TSD (ns) THD (ns)
MemData00:07, DM0 DQS0 1.067 0.973
MemData08:15, DM1 DQS1 1.074 0.973
MemData16:23, DM2 DQS2 1.082 0.973
MemData24:31, DM3 DQS3 1.088 0.973
ECC0:7, DM4 DQS4 1.012 0.973
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 65
Data Sheet
The feedback signal to the Feedback Data Capture Window is adjusted for propagation delay by the fine/coarse
delays and is automatically adjusted for variations in the DDR I/O due to supply voltage and temperature.
Compensation for driver/receiver variations is accomplished by driving and receiving the feedback signal on the
external MemFBD and MemFBR pins. Tuning the fine/coarse delays adjust for propagation delay. When properly
tuned, the feedback pulse is aligned to the first DQS in a four-beat burst such that the rising edge of DQS is
nominally centered on the feedback pulse. Software must adjust the pulse using the fine/coarse delays when
tuning read DQS delay.
Note: Using minimum trace length, connect MemFBD directly to MemFBR.
The data captured in Stage 1 is relative to the DQS timing domain and is held for four DDR 1X cycles. Stage 2
samples the data in Stage 1 attempting to capture the data in the DDR 1X domain. The on-time-sample clock from
the Stage 2 Store block samples the Stage 1 data at sample cycle T1, T2, T3, or T4. The sample cycle is either
selected by initialization software or can be automatically selected and adjusted by the DDR controller. The Stage
1 data is sampled a second time by the over sample clock at a delayed sample point. The delay between the on-
time-sample and over sample clocks is the Over-Sampling-Guard-Band.
The feedback pulse is sampled with the data captured by the first DQS in the four beat burst. A match of one or
both of the sample clocks with the feedback pulse is a hit. The DDR controller based on hits or misses by the on-
time sample and over sample clocks adjust the sample cycle in order to track variations in DQS. Burst data from a
sample hit is passed to Stage 3.
In Stage 3 the data is synchronized to the PLB clock domain and eventually driven onto the PLB bus. The data
captured on the rising and falling DQS edges is unpacked into the correct bit locations on the upper (0:63) and
lower (64:127) PLB bus. When ECC is enable, ECC checking and corrections is done after Stage 3.
Figure 11 illustrates how the three-stage read logic captures the data in the DQS timing domain and synchronizes
it to the PLB clock domain. The first DQS of four beat burst is roughly centered on feedback signal pulse.
PPC405EX – PowerPC 405EX Embedded Processor
66 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Figure 9. DDR SDRAM Read Data Path for a Single Data Bit
DDR SDRAM Read Cycle Timing
The following diagram illustrates the relationship of the signals involved with a DDR read operation.
Figure 10. DDR SDRAM Memory Data and DQS
PLB bus
Programmed
Delay
Package
Mux
Read DQS
C
D
FF: Flip-Flop
Q2
DQS
DDR 1X Clock
Mux
MemData
(x64+ECC)
(x64+ECC)
Read FIFO
PLB 1X Clock
Stage 2
Stage 1 Stage 3
FF PLB bus
[0:63]
[64:127]
DQS Rising
DQS Falling
Q3
0
2
Coarse Delay
Cycles
Driver
Rec
MemFBD
MemFBR
Ext FeedBack
Read Start
Feedback
Data Capture
Window
DDR 1X Clock
Stage 2 Store Oversampling
DQS aligned
CAS Lat Delay
FeedBack
Signal Gen
Fine Delay
T1 T2 T3 T4
Fine Delay
FF
FF
3
1
1
0
3
Edge Sync
Edge Sync
Upper
Lower
Signals
pins
FF
Q2_Ovs
FF
feedback signal Delay
+1
Compare
DDR 1X Clock
Oversampling
Clock
Read Latency adjust circuit
C
DFF
FF
Adjust
FF
Q3
(Guard Band)
Q2
ECC detection and correction if enabled occurs after Stage 3 before completing the read on the PLB.
On-time sample clock
(x4 + x1
2
Mux
Mux
ECC bits)
(x32 bits +
x8 bits ECC)
DQS
MemData
TSD
THD
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 67
Data Sheet
In the following example, the data strobes (DQS) and the data are shown to be coincident. There is actually a slight
skew as specified by the SDRAM specifications, and there can be additional skew due to loading and signal
routing. It is recommended that the signal length for all of the DQS signals be matched.
The following example shows the timing relationship between SDRAM DDR Data at the input pin and storing the
data in Stage 1.
Table 27. I/O Timing—DDR SDRAM Read Timing TSD and THD
1. TSD and THD are measured under worst case conditions.
2. Clock speed for the values in the table is 200MHz.
3. The time values in the table include 1/4 of a cycle at 200MHz (5ns x 0.25 = 1.25 ns).
4. To obtain adjusted TSD and THD values for lower clock frequencies, subtract 0.75 ns from the values in the table and add 1/4
of the cycle time for the lower clock frequency (e.g., TSD - 1.25 + 0.25TCYC).
Signal Names Reference Signal Read Data vs DQS Set up
TSD (ns)
Read Data vs DQS Hold
THD (ns)
MemData00:07 DQS0 0.27 0.45
MemData08:15 DQS1 0.27 0.45
MemData16:23 DQS2 0.27 0.45
MemData24:31 DQS3 0.27 0.45
ECC0:7 DQS4 0.27 0.45
PPC405EX – PowerPC 405EX Embedded Processor
68 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Figure 11. DDR SDRAM Read Cycle Timing—Example
DQS at Pin
MemData at Pin
D0 D2
High
Low
MemFBR at Pin
D0 D1 D2 D3 D4 D5 D6 D7 D8 D9
Data Out Stage 2
D1 D3
DDR 1X Clock
DDR 2X Clock
MemClkOut0 (Diff.)
Data Out Stage 1 (0)
Delayed DQS
Data out Stage 1 (2)
Data Out Stage 1 (1)
DDR 1X Clock cycle
Valid
Store 1st Data
T1 T2 T3 T4
Oversampling Guard Band
in Stage 2
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 69
Data Sheet
PCI Express (PCI-E) I/O Specifications
The following tables provide the required I/O timing information regarding the use of the PCI Express interface on
this chip.
Table 28. PCI-E Receiver I/O Specifications
Parameter Minimum Maximum Units Notes
Unit Interval (UI) 399.88 400.12 ps
Differential Rx peak-peak voltage 175 1200 mV
Receiver eye time opening 0.4 - UI
Maximum time delta between median and deviation from median - 0.3 UI
Rx differential return loss 10 - dB
Common mode Rx return loss 6 - dB
Receiver DC common mode impedance 40 60 Ω
DC differential impedance 80 120 Ω
Rx AC common mode voltage - 150 mV
DC Input CM input impedance during reset or power down 200 - kΩ
Electrical idle detect threshold 65 125 ns
Table 29. PCI-E Reference Clock I/O Specifications
Parameter Minimum Maximum Units Notes
PCI_E reference clock frequency (PCIEnClkC and PCIEnClkT ) 100 100 MHz 1
Accuracy -300 +300 ppm
Duty cycle 45 55 %
Peak-to-peak jitter for 1E-6 BER (1 x 10-6 bit error rate) -86ps3
Spread Spectrum Clock (SSC) frequency 30 33 kHz 2
Common mode voltage 0 1600 mV
Differential signal amplitude 200 1600 mV
Notes:
1. The PCI-E reference clock frequency specification does not include +/- 300ppm accuracy specification.
2. The data rate can be modulated from +0.5% to −0.5% of the nominal data rate frequency, at a modulation rate in the range not
exceeding 30kHz–33kHz. The +/- 600ppm requirement remains which requires the two communicating ports to be modulated so that
they never exceed a total of 600ppm difference. For most implementations, this requires that both ports have the same bit rate clock
source when the data is modulated with an SSC.
3. 1E-6 is the probability that the jitter is greater than 86ps peak-to-peak.
PPC405EX – PowerPC 405EX Embedded Processor
70 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Table 30. PCI-E Transmitter I/O Specifications
Parameter Minimum Maximum Units Notes
Unit Interval (UI) 399.88 400.12 ps
Differential p-p Tx voltage swing 800 - mV ppd
Low power differential p-p Tx voltage swing 400 - mV ppd
Tx de-emphasis level ratio -3.0 -4.0 dB
Minimum Tx eye width 0.75 - UI
Maximum time between the jitter median and maximum
deviation from the median -0.125UI
Transmitter rise and fall time 0.125 - UI
Maximum Tx PLL bandwidth - 22 MHz
Minimum Tx PLL BW for 3dB peaking 1.5 - MHz
Tx AC common mode voltage - 20 mV
Absolute Delta of DC Common Mode Voltage during L0 and
Electrical Idle. 0 100 mV
Absolute Delta of DC Common Mode Voltage between PCIEnTx
and PCIEnTx 025mV
Electrical Idle Differential Peak Output Voltage 0 20 mV
The amount of voltage change allowed during Receiver
Detection - 600 mV
Transmitter DC common-mode voltage 0 3.6 V
Transmitter short-circuit current limit - 90 mA
Minimum time spent in Electrical Idle 20 - ns
Maximum time to transition to a valid Electrical Idle after sending
an EIOS -8ns
Maximum transition time to valid differential signaling after
leaving Electrical Idle -8ns
Differential return loss 10 - dB
Common mode return loss 6 - dB
DC differential Tx impedance 80 120 Ω
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 71
Data Sheet
Initialization
The following describes the method by which initial chip settings are established when a system reset occurs.
Strapping
When the SysReset input is driven low (system reset), the state of certain I/O pins is read in order to enable default
initial conditions before PPC405EX start-up. The actual instant of capture is the nearest system clock edge before
the deassertion of reset. These pins must be strapped using external pull-up (logical 1) or pull-down (logical 0)
resistors to select the desired default conditions. The recommended pull-up is 3kΩ to +3.3V, or 10kΩ to +5V. The
recommended pull-down is 1kΩ to GND. These pins are only used for strap functions during reset. They are used
for other signals during normal operation. The following table lists the strapping pins along with their functions and
strapping options. The signal names assigned to the pins for normal operation appear below the pin number.
Table 31. Strapping Pin Assignments
Pin Strapping
Initialization Source Option F04
(UART0DCD)
F02
(UART0DSR)
G02
(UART0CTS)
EBC 8-bit wide ROM A 0 0 0
EBC 16-bit wide ROM B 0 0 1
EBC 16-bit wide ROM C 0 1 0
EBC 8-bit wide NAND Flash D 0 1 1
EBC 8-bit wide NAND Flash E 1 0 0
IIC ROM at address 0xA8 G 1 0 1
EBC 8-bit wide ROM F 1 1 0
IIC ROM at address 0xA4 H 1 1 1
Note: See the PPC405EX Embedded Processor User’s Manual for option descriptions and other details regarding the boot process.
PPC405EX – PowerPC 405EX Embedded Processor
72 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Revision Log
Date Version Contents of Modification
02/27/2007 1.00 Initial creation of document.
03/01/2007 1.01 Updates following review of initial document.
03/22/2007 1.02
Change package drawing to eliminate confusion.
Expand system memory map.
Define FSource0 signal as Reserved.
Add Recommended Operating Conditions data.
Add thermal data.
Misc. updates and additions.
04/24/2007 1.03 Misc. updates and additions including some limited timing data.
05/24/2007 1.04
Correct one of three ball numbers assigned to PerData28.
Swap four balls between VDD and GND.
Swap one ball between OVDD and SVDD.
Correct typographical errors in Table 3.
Add missing alphabetical entries for PerAddr05, NAND Flash, and IIC1.
Add output current values to Tables 15 and 16.
06/04/2007 1.05
Input various review comments.
Update Table 6 Notes column.
Update Block Diagram.
Swap SAVDD an EAVDD signal name assignments on package balls.
Add two UART configurations.
Add DDR SDRAM section extracted from 460EX with changes appropriate for 405EX.
Update timing information for all interfaces.
Add power values.
Update I/O capacitance values.
06/07/2007 1.06 Remove Confidential status.
Input various review comments.
06/28/2007 1.07
Input review comments and corrections.
Change default signals for GPIO balls to GPIO00–GPIO27 signals.
Eliminate confusing terminology in initialization section.
07/12/2007 1.08 Change voltage names so that SDRAM voltage is always SVDD for both DDR1 and DDR2 types.
Six voltage pins originally labeled SVDD changed to EOVDD.
08/21/2007 1.09 Update GMCRefClk specifications (rise time, jitter, etc.)
10/25/2007 1.11
Add I/O timing figures for RGMII signals.
Correct AMCC telephone numbers.
Change PerErr to always pull down.
Implement Doc Issue 374.
Change chip revision level from A to B (Doc issue 380).
Implement Doc Issue 381.
Revise I/O timing figures for RGMII signals.
Major updates to DDR SDRAM section (and other parts of the DS) (Doc Issue 392).
Add PCI-E I/O specifications.
I/O timing values updates.
Change boot-from-EBC support (Doc Issue 383).
11/20/2007 1.12 Misc. updates.
Change all 667 MHz specs to 600 MHz.
PPC405EX – PowerPC 405EX Embedded Processor Revision 1.23 - January 28, 2009
AMCC Proprietary 73
Data Sheet
12/06/2007 1.13
Misc. updates.
Change all 667 MHz specs to 600 MHz.
Document Issues 412 and 435 implemented (includes removal of 333MHz parts and tape-and-
reel packaging).
01/04/2008 1.14 Misc. updates from Doc Issue 440.
Note: Automatic change bars are now included on all changes.
01/15/2008 1.15
Package tolerance update.
Implemented Doc Issue 447:
Supply voltage changes (wider voltage range with increased power consumption).
Remove common mode voltage specs.
Change DDR SDRAM and PCI-E specs.
01/16/2008 1.16 Correct voltage changes.
02/11/2008 1.17
Update SDRAM write timing.
Update PCIEnClk signal description.
Increase PCI-E differential signal amplitude to 1600mV (Doc Issue 468).
02/15/2008 1.18 Change power consumption numbers from estimated to measured.
03/19/2008 1.19
Misc. updates in Doc Issue 482.
Remove GMCMDIO timing numbers (Doc Issue 495).
Correct bracket placement on signal name (Doc Issue 500).
05/02/2008 1.20 Add power sequence information (Doc Issue 509).
Misc. updates.
07/09/2008 1.21
Updated part numbers, revision level, and PVR.
Added extended temperature operation of 533MHz part at 400MHz or less.
Added maximum power for each speed.
Added some functional unit power consumption figures.
11/11/2008 1.22
Change part number nomenclature.
Doc Issue 548.
Bugzilla Issue 5097. Change RGMII I/O timing.
Remove Preliminary designation.
Update GMII and RGMII timing.
Bugzilla Issue 5170. Update GMII and RGMII timing.
01/28/2009 1.23 Bugzilla Issue 5389. Added new row and footnote at the bottom of Table 18.
Date Version Contents of Modification
PPC405EX – PowerPC 405EX Embedded Processor
74 AMCC Proprietary
Revision 1.23 - January 28, 2009
Data Sheet
Applied Micro Circuits Corporation
215 Moffett Park Drive, Sunnyvale, CA 94089
Phone: (408) 542-8600 — (800) 840-6055 — Fax: (408) 542-8601
http://www.amcc.com
AMCC reserves the right to make changes to its products, its datasheets, or related documentation, without notice and war-
rants its products solely pursuant to its terms and conditions of sale, only to substantially comply with the latest available
datasheet. Please consult AMCC’s Term and Conditions of Sale for its warranties and other terms, conditions and limitations.
AMCC may discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest
version of relevant information to verify, before placing orders, that the information is current. AMCC does not assume any lia-
bility arising out of the application or use of any product or circuit described herein, neither does it convey any license under
its patent rights nor the rights of others. AMCC reserves the right to ship devices of higher grade in place of those of lower
grade.
AMCC SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE
SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL
APPLICATIONS.
AMCC is a registered Trademark of Applied Micro Circuits Corporation.
Copyright © 2008 Applied Micro Circuits Corporation. All Rights Reserved.
6310 Sequence Drive, San Diego, CA 92121 (858) 450-9333 Fax (858) 450-9885 http://www.appliedmicro.com
Product Change Notification: 110209-02
Update 11/19/09: Implementation and First Shipment date changed from February 13, 2009 to
February 13, 2010.
Product Change Notification Date November 13, 2009
Product Change Title PPC405EX and PPC405EXr Transition from revision C to revision D
Affected Part Number List All 405EX and 405EXr revision C part numbers.
See ‘From’ part numbers in the next section.
Description of Change
(Part Number From/To)
From: To:
PPC405EX-SSC400T PPC405EX-SSD400T
PPC405EX-SSC533T PPC405EX-SSD533T
PPC405EX-SSC600T PPC405EX-SSD600T
PPC405EX-NSC400T PPC405EX-NSD400T
PPC405EX-NSC533T PPC405EX-NSD533T
PPC405EX-NSC600T PPC405EX-NSD600T
PPC405EX-SPC400T PPC405EX-SPD400T
PPC405EX-SPC533T PPC405EX-SPD533T
PPC405EX-SPC600T PPC405EX-SPD600T
PPC405EX-NPC400T PPC405EX-NPD400T
PPC405EX-NPC533T PPC405EX-NPD533T
PPC405EX-NPC600T PPC405EX-NPD600T
PPC405EXr-SSC333T PPC405EXr-SSD333T
PPC405EXr-SSC400T PPC405EXr-SSD400T
PPC405EXr-SSC533T PPC405EXr-SSD533T
PPC405EXr-NSC333T PPC405EXr-NSD333T
PPC405EXr-NSC400T PPC405EXr-NSD400T
PPC405EXr-NSC533T PPC405EXr-NSD533T
PPC405EXr-SPC333T PPC405EXr-SPD333T
PPC405EXr-SPC400T PPC405EXr-SPD400T
PPC405EXr-SPC533T PPC405EXr-SPD533T
PPC405EXr-NPC333T PPC405EXr-NPD333T
PPC405EXr-NPC400T PPC405EXr-NPD400T
PPC405EXr-NPC533T PPC405EXr-NPD533T
Description of Change Errata Fixes (Reference PPC405EX and PPC405EXr errata for
details.)
Die revision transition from Rev C (Rev1.2) to Rev D (Rev1.3)
6310 Sequence Drive, San Diego, CA 92121 (858) 450-9333 Fax (858) 450-9885 http://www.appliedmicro.com
Reason for Change Errata Fixes.
Qualification/Test Data Available upon request
Sample Availability Date Available Now
Implementation Date February 13, 2010. After this date, orders of the older version
(Rev. C) will only be accepted based on available inventory.
First Shipment Date February 13, 2010
Expected Customer Actions
This form is the official notification of this change. Please review this
PCN carefully. If there are any concerns, please notify your AMCC
Sales Representative, Sales Manager or Field Applications Engineer
within 30 days. Automatic acceptance of this change shall be
assumed if no written objection is received.
Please direct sample requests to your Inside Sales Representative or
go to http://www.appliedmicro.com/Sales/SampleRequest.html
Contact for Inquiries slsmith@amcc.com
