SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 D D D D D Wide Operating Voltage Range of 2 V to 6 V Outputs Can Drive Up To 10 LSTTL Loads Low Power Consumption, 80-A Max ICC Typical tpd = 14 ns 4-mA Output Drive at 5 V 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SN54HC161 . . . FK PACKAGE (TOP VIEW) VCC RCO QA QB QC QD ENT LOAD A B NC C D 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 QA QB NC QC QD ENP GND NC LOAD ENT CLR CLK A B C D ENP GND Low Input Current of 1 A Max Internal Look-Ahead for Fast Counting Carry Output for n-Bit Cascading Synchronous Counting Synchronously Programmable CLK CLR NC VCC RCO SN54HC161 . . . J OR W PACKAGE SN74HC161 . . . D, N, NS, OR PW PACKAGE (TOP VIEW) D D D D D NC - No internal connection description/ordering information These synchronous, presettable counters feature an internal carry look-ahead for application in high-speed counting designs. The 'HC161 devices are 4-bit binary counters. Synchronous operation is provided by having all flip-flops clocked simultaneously so that the outputs change coincident with each other when so instructed by the count-enable (ENP, ENT) inputs and internal gating. This mode of operation eliminates the output counting spikes that are normally associated with synchronous (ripple-clock) counters. A buffered clock (CLK) input triggers the four flip-flops on the rising (positive-going) edge of the clock waveform. ORDERING INFORMATION PACKAGE TA PDIP - N SOIC - D -40C to 85C SOP - NS TSSOP - PW -55C -55 C to 125 125C C ORDERABLE PART NUMBER Tube of 25 SN74HC161N Tube of 40 SN74HC161D Reel of 2500 SN74HC161DR Reel of 250 SN74HC161DT Reel of 2000 SN74HC161NSR Tube of 90 SN74HC161PW Reel of 2000 SN74HC161PWR TOP-SIDE MARKING SN74HC161N HC161 HC161 HC161 Reel of 250 SN74HC161PWT CDIP - J Tube of 25 SNJ54HC161J SNJ54HC161J CFP - W Tube of 150 SNJ54HC161W SNJ54HC161W LCCC - FK Tube of 55 SNJ54HC161FK SNJ54HC161FK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated !"# $"%&! '#( '"! ! $#!! $# )# # #* "# '' +,( '"! $!#- '# #!#&, !&"'# #- && $##( $'"! !$& . / 0 121 && $## # ##' "&# )#+# #'( && )# $'"! $'"! $!#- '# #!#&, !&"'# #- && $##( POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 description/ordering information (continued) These counters are fully programmable; that is, they can be preset to any number between 0 and 9 or 15. As presetting is synchronous, setting up a low level at the load input disables the counter and causes the outputs to agree with the setup data after the next clock pulse, regardless of the levels of the enable inputs. The clear function for the 'HC161 devices is asynchronous. A low level at the clear (CLR) input sets all four of the flip-flop outputs low, regardless of the levels of the CLK, load (LOAD), or enable inputs. The carry look-ahead circuitry provides for cascading counters for n-bit synchronous applications without additional gating. Instrumental in accomplishing this function are ENP, ENT, and a ripple-carry output (RCO). Both ENP and ENT must be high to count, and ENT is fed forward to enable RCO. Enabling RCO produces a high-level pulse while the count is maximum (9 or 15 with QA high). This high-level overflow ripple-carry pulse can be used to enable successive cascaded stages. Transitions at ENP or ENT are allowed, regardless of the level of CLK. These counters feature a fully independent clock circuit. Changes at control inputs (ENP, ENT, or LOAD) that modify the operating mode have no effect on the contents of the counter until clocking occurs. The function of the counter (whether enabled, disabled, loading, or counting) is dictated solely by the conditions meeting the stable setup and hold times. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 logic diagram (positive logic) LOAD ENT ENP 9 10 15 LD 7 RCO CK CLK CLR A B C D 2 1 CK LD R M1 G2 1, 2T/1C3 G4 3D 4R 3 M1 G2 1, 2T/1C3 G4 3D 4R 4 M1 G2 1, 2T/1C3 G4 3D 4R 5 M1 G2 1, 2T/1C3 G4 3D 4R 6 14 13 12 11 QA QB QC QD For simplicity, routing of complementary signals LD and CK is not shown on this overall logic diagram. The uses of these signals are shown on the logic diagram of the D/T flip-flops. Pin numbers shown are for the D, J, N, NS, PW, and W packages. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 logic symbol, each D/T flip-flop LD (Load) M1 TE (Toggle Enable) G2 CK (Clock) 1, 2T/1C3 G4 D (Inverted Data) 3D R (Inverted Reset) 4R Q (Output) logic diagram, each D/T flip-flop (positive logic) CK LD TE LD TG TG LD Q TG TG CK D TG CK R The origins of LD and CK are shown in the logic diagram of the overall device. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 CK TG CK SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 typical clear, preset, count, and inhibit sequence The following sequence is illustrated below: 1. Clear outputs to zero (asynchronous) 2. Preset to binary 12 3. Count to 13, 14, 15, 0, 1, and 2 4. Inhibit CLR LOAD A Data Inputs B C D CLK ENP ENT QA Data Outputs QB QC QD RCO 12 13 14 15 0 1 Count 2 Inhibit Sync Preset Clear Async Clear POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) SN54HC161 VCC VIH Supply voltage High-level input voltage VCC = 2 V VCC = 4.5 V VCC = 6 V VCC = 2 V VIL VI VO t/v Low-level input voltage MIN NOM MAX 2 5 6 MIN NOM MAX 2 5 6 1.5 1.5 3.15 3.15 4.2 4.2 VCC = 4.5 V VCC = 6 V Input voltage 0 Output voltage 0 Input transition rise/fall time SN74HC161 VCC = 2 V VCC = 4.5 V VCC = 6 V 0.5 1.35 1.35 1.8 1.8 0 0 V V 0.5 VCC VCC UNIT VCC VCC 1000 1000 500 500 400 400 V V V ns TA Operating free-air temperature -55 125 -40 85 C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. If this device is used in the threshold region (from VILmax = 0.5 V to VIHmin = 1.5 V), there is a potential to go into the wrong state from induced grounding, causing double clocking. Operating with the inputs at tt = 1000 ns and VCC = 2 V does not damage the device; however, functionally, the CLK inputs are not ensured while in the shift, count, or toggle operating modes. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = -20 A VOH IOL = 20 A VOL II ICC VI = VCC or 0 VI = VCC or 0, TA = 25C TYP MAX MIN MAX SN74HC161 MIN 1.9 1.998 1.9 1.9 4.4 4.499 4.4 4.4 6V 5.9 5.999 5.9 5.9 4.5 V 3.98 4.3 3.7 3.84 6V 5.48 5.8 5.2 MAX UNIT V 5.34 2V 0.002 0.1 0.1 0.1 4.5 V 0.001 0.1 0.1 0.1 6V 0.001 0.1 0.1 0.1 4.5 V 0.17 0.26 0.4 0.33 6V 0.15 0.26 0.4 0.33 6V 0.1 100 1000 1000 nA 8 160 80 A 3 10 10 10 pF IO = 0 6V Ci SN54HC161 2V VI = VIH or VIL IOL = 4 mA IOL = 5.2 mA MIN 4.5 V VI = VIH or VIL IOH = -4 mA IOH = -5.2 mA VCC 2 V to 6 V V timing requirements over recommended operating free-air temperature range (unless otherwise noted) VCC fclock Clock frequency CLK high or low tw Pulse duration CLR low A, B, C, or D LOAD low tsu Setup time before CLK ENP, ENT CLR inactive th Hold time, all synchronous inputs after CLK CLK POST OFFICE BOX 655303 TA = 25C MIN MAX SN54HC161 MIN MAX SN74HC161 MIN MAX 2V 6 4.2 5 4.5 V 31 21 25 6V 36 25 29 2V 80 120 100 4.5 V 16 24 20 6V 14 20 17 2V 80 120 100 4.5 V 16 24 20 6V 14 20 17 2V 150 225 190 4.5 V 30 45 38 6V 26 38 32 2V 135 205 170 4.5 V 27 41 34 6V 23 35 29 2V 170 255 215 4.5 V 34 51 43 6V 29 43 37 2V 125 190 155 4.5 V 25 38 31 6V 21 32 26 2V 0 0 0 4.5 V 0 0 0 6V 0 0 0 * DALLAS, TEXAS 75265 UNIT MHz ns ns ns 7 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) fmax RCO CLK tpd Any Q ENT RCO Any Q tPHL CLR RCO tt Any VCC MIN TA = 25C TYP MAX SN54HC161 MIN MAX SN74HC161 MIN 2V 6 14 4.2 5 4.5 V 31 40 21 25 6V 36 44 25 29 MAX UNIT MHz 2V 83 215 325 270 4.5 V 24 43 65 54 6V 20 37 55 46 2V 80 205 310 255 4.5 V 25 41 62 51 6V 21 35 53 43 2V 62 195 295 245 4.5 V 17 39 59 49 6V 14 33 50 42 2V 105 210 315 265 4.5 V 21 42 63 53 6V 18 36 54 45 2V 110 220 330 275 4.5 V 22 44 66 55 6V 19 37 56 47 2V 38 75 110 95 4.5 V 8 15 22 19 6V 6 13 19 16 ns ns ns operating characteristics, TA = 25C PARAMETER Cpd 8 TEST CONDITIONS Power dissipation capacitance No load POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TYP 60 UNIT pF SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 PARAMETER MEASUREMENT INFORMATION From Output Under Test VCC High-Level Pulse Test Point 50% 50% 0V tw CL = 50 pF (see Note A) VCC Low-Level Pulse 50% 50% 0V LOAD CIRCUIT VOLTAGE WAVEFORMS PULSE DURATIONS Input VCC 50% 50% 0V tPLH Reference Input VCC 50% In-Phase Output 50% 10% 0V tsu Data Input 50% 10% 90% tr tPHL VCC 50% 10% 0 V 90% 90% tr th 90% tPHL Out-of-Phase Output 90% VOLTAGE WAVEFORMS SETUP AND HOLD AND INPUT RISE AND FALL TIMES tPLH 50% 10% tf tf VOH 50% 10% VOL tf 50% 10% 90% VOH VOL tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES NOTES: A. CL includes probe and test-fixture capacitance. B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO = 50 , tr = 6 ns, tf = 6 ns. C. For clock inputs, fmax is measured when the input duty cycle is 50%. D. The outputs are measured one at a time with one input transition per measurement. E. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 APPLICATION INFORMATION n-bit synchronous counters This application demonstrates how the look-ahead carry circuit can be used to implement a high-speed n-bit counter. The 'HC161 devices count in binary. Virtually any count mode (modulo-N, N1-to-N2, N1-to-maximum) can be used with this fast look-ahead circuit. The application circuit shown in Figure 2 is not valid for clock frequencies above 18 MHz (at 25C and 4.5-V VCC). The reason for this is that there is a glitch that is produced on the second stage's RCO and every succeeding stage's RCO. This glitch is common to all HC vendors that Texas Instruments has evaluated, in addition to the bipolar equivalents (LS, ALS, AS). 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 APPLICATION INFORMATION LSB CTR CT=0 M1 3CT=MAX G3 CLR Clear (L) LOAD ENT Count (H)/ Disable (L) ENP CLK RCO G4 C5/2,3,4+ Load (L) A 1,5D [1] QA Count (H)/ Disable (L) B [2] QB C [3] QC Clock D [4] QD CTR CT=0 M1 3CT=MAX G3 CLR LOAD ENT ENP CLK RCO G4 C5/2,3,4+ A 1,5D [1] QA B [2] QB C [3] QC D [4] QD CTR CT=0 M1 3CT=MAX G3 CLR LOAD ENT ENP CLK RCO G4 C5/2,3,4+ A 1,5D [1] QA B [2] QB C [3] QC D [4] QD CTR CT=0 M1 3CT=MAX G3 CLR LOAD ENT ENP CLK RCO G4 C5/2,3,4+ A 1,5D [1] QA B [2] QB C [3] QC D [4] QD To More-Significant Stages Figure 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 APPLICATION INFORMATION The glitch on RCO is caused because the propagation delay of the rising edge of QA of the second stage is shorter than the propagation delay of the falling edge of ENT. RCO is the product of ENT, QA, QB, QC, and QD (ENT x QA x QB x QC x QD). The resulting glitch is about 7-12 ns in duration. Figure 3 shows the condition in which the glitch occurs. For simplicity, only two stages are being considered, but the results can be applied to other stages. QB, QC, and QD of the first and second stage are at logic one, and QA of both stages are at logic zero (1110 1110) after the first clock pulse. On the rising edge of the second clock pulse, QA and RCO of the first stage go high. On the rising edge of the third clock pulse, QA and RCO of the first stage return to a low level, and QA of the second stage goes to a high level. At this time, the glitch on RCO of the second stage appears because of the race condition inside the chip. 1 2 3 4 5 CLK ENT1 QB1, QC1, QD1 QA1 RCO1, ENT2 QB2, QC2, QD2 QA2 RCO2 Glitch (7-12 ns) Figure 3 The glitch causes a problem in the next stage (stage three) if the glitch is still present when the next rising clock edge appears (clock pulse 4). To ensure that this does not happen, the clock frequency must be less than the inverse of the sum of the clock-to-RCO propagation delay and the glitch duration (tg). In other words, fmax = 1/(tpd CLK-to-RCO + tg). For example, at 25C at 4.5-V VCC, the clock-to-RCO propagation delay is 43 ns and the maximum duration of the glitch is 12 ns. Therefore, the maximum clock frequency that the cascaded counters can use is 18 MHz. The following tables contain the fclock, tw, and fmax specifications for applications that use more than two 'HC161 devices cascaded together. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCLS297D - JANUARY 1996 - REVISED SEPTEMBER 2003 APPLICATION INFORMATION timing requirements over recommended operating free-air temperature range (unless otherwise noted) VCC fclock Clock frequency TA = 25C MIN MAX Pulse duration, CLK high or low MIN MAX SN74HC161 MIN MAX 2V 3.6 2.5 2.9 4.5 V 18 12 14 6V tw SN54HC161 21 14 UNIT MHz 17 2V 140 200 170 4.5 V 28 40 36 6V 24 36 30 ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Note 4) PARAMETER FROM (INPUT) TO (OUTPUT) fmax VCC TA = 25C MIN MAX SN54HC161 MIN MAX SN74HC161 MIN 2V 3.6 2.5 2.9 4.5 V 18 12 14 6V 21 14 17 MAX UNIT MHz NOTE 4: These limits apply only to applications that use more than two 'HC161 devices cascaded together. If the 'HC161 devices are used as a single unit, or only two cascaded together, then the maximum clock frequency that the device can use is not limited because of the glitch. In these situations, the device can be operated at the maximum specifications. A glitch can appear on RCO of a single 'HC161 device, depending on the relationship of ENT to CLK. Any application that uses RCO to drive any input except an ENT of another cascaded 'HC161 device must take this into consideration. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type 5962-8407501VEA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type 5962-8407501VFA ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) 84075012A ACTIVE LCCC FK 20 1 TBD 8407501EA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type 8407501FA ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type JM38510/66302BEA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type JM38510/66302BFA ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type SN54HC161J ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type SN74HC161D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DE4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DRE4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161DTG4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161N ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN74HC161N3 OBSOLETE PDIP N 16 TBD Call TI SN74HC161NE4 ACTIVE PDIP N 16 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN74HC161NSR ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161NSRE4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161NSRG4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWE4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM 25 Addendum-Page 1 POST-PLATE N / A for Pkg Type Call TI PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74HC161PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC161PWTG4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ54HC161FK ACTIVE LCCC FK 20 1 TBD SNJ54HC161J ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type SNJ54HC161W ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) no Sb/Br) POST-PLATE N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Jul-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74HC161DR Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN74HC161NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 SN74HC161PWR TSSOP PW 16 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Jul-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74HC161DR SOIC D 16 2500 333.2 345.9 28.6 SN74HC161NSR SO NS 16 2000 346.0 346.0 33.0 SN74HC161PWR TSSOP PW 16 2000 346.0 346.0 29.0 Pack Materials-Page 2 MECHANICAL DATA MLCC006B - OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated