Ma y 2003 1/23
®
VIPer100/SP
- VIP er 100 A/AS P
SMPS PRIMARY I.C.
1
ADJUSTABLE SWITCHING FREQUENCY UP
TO 200 kHz
CURRENT MODE CONTROL
SOFT START AND SHUT DOWN CONTROL
AUTOMA TIC BURST MODE OPERATION IN
STAND- BY CONDITION ABLE TO MEET
“BLUE ANGEL” NORM (<1w TOTAL POWER
CONSUMPTION)
INTERNAL LY TRIMMED ZENER REFERENCE
UNDERVOLTAGE LOCK-OUT WITH
HYSTERESIS
INTEGRATED START -UP SUPPLY
AVALANCHE RUGGED
OVERTEMPERATURE PROTECTION
LOW STAND-BY CURRENT
ADJUSTABLE CURRENT LIMITATION
DESCRIPTION
VIPer100/100A, made using VIPower M0
Technolog y, combines on the same silicon chip a
state-of-the-art PWM circuit together with an
optimized high voltage avalanche rugged Vertical
Power MOSFET (620V or 700V / 3A).
Typ ica l applic ations cover off lin e p ower supp lies
with a secondary power capability of 50 W in wide
range c on diti on an d 100W i n si ng le ran ge or with
doubler configuration. It is compatible from both
primary or secondary regulation loop despite
using around 50% less components when
compared with a discrete solution. Burst mode
operation is an additional feature of this device,
offering the possibility to operate in stand-by
mode without extra components.
TYPE VDSS InRDS(on)
VIPer100/SP 620V 3 A 2.5
VIPer100A/ASP 700V 3 A 2.8
BLOCK DIAGRAM
PEN TAW ATT HV PENTAWATT HV
1
10
PowerSO-10(022Y)
FC00231
VDD
OSC
COMP
DRAIN
SOURCE
13 V
UVLO
LOGIC
SECURITY
LATCH PWM
LATCH
FF
FF
R/S SQS
R1
R2 R3Q
OSCILLATOR
OVERTEMP.
DETECTOR
ERROR
AMPLIFIER_
+
0.5 V +
_1.7
µ s
DELAY 250 ns
BLANKING CURRENT
AMPLIFIER
ON/OFF
0.5V
1 V/A
_
+
+
_
4.5 V
2/23
VIPer100/SP - VIPer100A/ASP
ABSOLUTE MAXIMUM RATING
THERMAL DATA
(*) Wh en m ounted usi ng the min im um r ec ommended pa d s iz e on FR-4 b oar d.
CONNECTI ON DIAGRAMS (Top View)
CURRENT AND VOLTAGE CONVENTIO NS
Symbol Parameter Value Unit
VDS
Conti nuous Drain- Source Voltage (Tj=25 to 12 C)
for VIPer100/SP
for VIPer100A/ASP -0.3 to 620
-0.3 to 700 V
V
IDMaximum Curr ent In tern al l y l im ited A
VDD Supply Voltage 0 to 15 V
VOSC Volt age Range I nput 0 to VDD V
VCOMP Vol tage Range Input 0 to 5 V
ICOMP Maximum Con tinuous Curre nt ± 2mA
V
esd El ectros tatic Dischar ge (R =1.5k; C=100pF) 4000 V
ID(AR)
Avalanche D rain- Source Current, Repeti tive or Not Repetitiv e
(Tc=100°C; Pulse width limited by Tj max; δ < 1%)
for VIPer100/SP
for VIPer100A/ASP
2
1.4 A
A
Ptot Power Dissipation at Tc=25ºC82W
T
j
Junction Operating Temperature Internally limited °C
Tstg Storage Temperature -65 to 150 °C
Sym bol Parameter PEN TAW ATT HV Pow erSO-10(*) Unit
Rthj-case Thermal Resi stance Junct ion-case Max 1.4 1.4 °C/W
Rthj-amb. Thermal Resistance Ambient-case Max 60 50 °C/W
1
PENTAW ATT HV PENTAWATT HV (022Y) PowerSO-10
-
+
13V
OSC
COMP SOURCE
DRAINVDD
VCOMP
VOSC
VDD VDS
ICOMP
IOSC
IDD ID
FC00020
VIPer100/SP - VIPer100A/ASP
3/23
ORDERING NUM BERS
PINS FUNCTIONAL DESCRI PTION
DRAIN PIN:
Integrated Power MOSFET drain pin. It provides
internal bias current during start-up via an
integrated high voltage current source which is
swit che d of f du ri ng norm al op eration. The de v ice
is able to han dle an unclamped current during its
norma l opera tion, assu ring self pr otectio n agains t
voltage surges, PCB stray inductance, and
allowing a snubberless operation for low output
power.
SOURCE Pin:
Power MOSFET source pin. Primary side circuit
common ground connection.
VDD Pin:
This pin provides two functions :
- It corres ponds to th e low voltage su pply of the
control part of the circuit. If VDD goes below 8V,
the s tart- up cur rent sou rce is activated and the
output pow er MOS FET is sw itched off unti l the
VDD voltage reaches 11V. During this phase,
the internal current consumption is reduced,
the VDD pin i s sour c ing a curre nt of about 2 mA
and the COMP pin is shorted to ground. After
that, the current source is shut down, and the
device tries to start up by switching again.
- This pin is also connected to the error amplifier,
in order to allow primary as well as seco ndary
regulation configurations. In case of primary
regulation, an internal 13V trimmed reference
voltage is used to maintain VDD at 13V. For
secondary regulation, a voltage between 8.5V
and 12.5V will be put on VDD pin by transformer
design, in order to stuck the output of the
transconductance amplifier to the high state.
The COMP pin behaves as a constant current
source, and can easily be connected to the
output of an optocoupler. Note that any
overvoltage due to regulation loop failure is still
detected by the error amplifier through the VDD
voltage, which cannot overpass 13V. The
outp ut voltage will be somewhat higher than the
nominal one, but still under control.
COMP PIN:
This pin provides two functions :
- It is the output of the error transconductance
amplifier, and allows for the connection of a
compensation network to provide the desired
transfer function of the regulation loop. Its
bandwidth can be easily adjusted to the
needed value with usual components value. As
stated above, secondary regulation
configurations are also implemented through
the COMP pin.
- When the COMP voltag e is going below 0.5V,
the shut-down of the circuit occurs, with a zero
duty cycle fo r the power M OSFET. This feature
can b e used to swi tch off t he c on verte r, an d i s
automatically activated by the regulation loop
(whatever is the configuration) to provide a
burst mode operation in case of negligible
output power or open load condition.
OSC PIN:
An Rt-Ct network must be connected on that pin to
define the switching frequency. Note that despite
the connection of Rt to VDD, no significant
frequenc y chang e oc curs for V DD varying from 8V
to 15V. It provides also a synchronisation
capability, when connected to an external
frequency source.
PENTAWATT HV PENTA W ATT HV (022Y) Pow erSO-10
VIPer100
VIPer100A VIPer100 ( 022Y)
VIPer100 A (022Y) VIPer100SP
VIPer100ASP
1
4/23
VIPer100/SP - VIPer100A/ASP
AVALANCHE CHARACTERISTICS
ELECTRICAL CHARACT ERISTICS (Tj=25°C; V DD=13V, unless otherwise specified)
POWER SECTION
(1) On Inductiv e Load, Clam ped.
SUPPLY SECTION
Symbol Parameter Max Value Unit
ID(AR)
Av ala n che Curren t, Re p eti tiv e or Not Rep eti tiv e
(pulse widht limited by Tj max; δ < 1%)
for VIPer100/SP
for VIPer100A/ ASP (see fig.12)
2
1.4 A
A
E(AR) S ingle Pu lse A v alanch e En ergy
(s tart ing Tj =25º C, ID=ID(ar)) (see fig.12) 60 mJ
S ymbol Parameter Test Condi tions Min Typ M ax Un it
BVDSS Drain-Source Voltage ID=1mA; VCOMP=0V
for VIPer100/SP
for VIPer100A/ASP (see fi g.5) 620
700 V
V
IDSS Off-State Drain Cur rent VCOMP=0V; Tj=125°C
VDS=620V for VIPer100/SP
VDS=700V for VIPer100A/ASP 1
1mA
mA
RDS(on) St atic Dr ain-So urce
On Resistance
ID=2A
for VIPer100/SP
for VIPer100A/ASP
ID=2A; Tj=100°C
for VIPer100/SP
for VIPer100A/ASP
2.0
2.3 2.5
2.8
4.5
5.0
tf Fall Time ID=0.2A; VIN=300V (1)
(See f ig. 3) 100 ns
tr Rise Time ID=0.4A; VIN=300V (1)
(See f ig. 3) 50 ns
Coss Output Capacitance VDS=25V 150 pF
S ymbol Parameter Test Condi tions Min Typ M ax Un it
IDDch Start -Up Charging
Current VDD=5V; VDS=35V
(see f ig. 2 an d fig. 15) -2 mA
IDD0 O perat ing Supp ly Cu rr ent VDD=12V ; F SW=0kHz
(see f ig. 2) 12 16 mA
IDD1 O perat ing Supp ly Cu rr ent VDD=12V ; F sw=100kHz 15.5 mA
IDD2 O perat ing Supp ly Cu rr ent VDD=12V ; F sw=200kHz 19 mA
VDDoff Und ervoltage Shut down (See f ig. 2) 7.5 8 9 V
VDDon Undervoltage Reset (See fig. 2) 11 12 V
VDDhyst Hyst ere sis Start-u p (See f ig. 2) 2.4 3 V
VIPer100/SP - VIPer100A/ASP
5/23
ELECTRICAL CHARACT ERISTICS (continued)
OSCILLATOR SECTION
ERROR A MPLIFIER SECTION
PWM COMPARATOR SECTION
SHUTDOWN AND OVERTEMPERATURE SECTION
S ymbol Parameter Test Condi tions Min Typ M ax Un it
FSW Osc il lator Frequency
Total Variation
RT=8.2K; CT=2.4nF
VDD=9 to 15V;
with RT± 1%; CT± 5%
(see f ig. 6 an d fig. 9)
90 100 110 kHz
VOSCIH Oscillator Peak Voltage 7.1 V
VOSCIL Oscillator Valley Voltage 3.7 V
S ymbol Parameter Test Condi tions Min Typ M ax Un it
VDDREG VDD Regul atio n Point ICOMP=0m A (see fig . 1) 12.6 13 13.4 V
VDDreg Total Variation Tj=0 to 100°C 2 %
GBW Unity Gain Bandwidth From Input =VDD to Output = VCOMP
COMP p in is ope n (see fig. 10) 150 kHz
AVOL Ope n Loop Voltage G ain COMP p in is ope n (see fig. 10) 45 52 dB
GmDC Transconductance VCOMP=2.5 V (see fig . 1) 1.1 1.5 1.9 m A/V
VCOMPLO Output Low Level ICOMP=-400µA; VDD=14V 0.2 V
VCOMPHI Output High Level ICOMP=400µA; VDD=12V 4.5 V
ICOMPLO Output Low Current
Capability VCOMP=2.5V; VDD=14V -600 µA
ICOMPHI Output High Current
Capability VCOMP=2.5V; VDD=12V 600 µA
S ymbol Parameter Test Condi tions Min Typ M ax Un it
HID VCOMP / IDPEAK VCOMP=1 to 3 V 0.711.3V/A
V
COMPoff VCOMP Of f s e t IDPEAK=10mA 0.5 V
IDpeak Peak Current Limitation VDD=12V; COMP pin open 3 4 5.3 A
tdCurrent Se nse Delay to
Turn-Off ID=1A 250 ns
tbBlanking Time 250 360 ns
ton(min) Mi nimum On Time 350 1200 ns
S ymbol Parameter Test Condi tions Min Typ M ax Un it
VCOMPth Restart Thresh old (see f ig. 4) 0.5 V
tDISsu Disa ble Set Up Time (see f ig. 4) 1.7 5 µs
Ttsd T h erma l Sh utdow n
Temperature (See fig. 8) 140 170 °C
Thyst T h ermal Sh utdown
Hysteresis (See fig. 8) 40 °C
6/23
VIPer100/SP - VIPer100A/ASP
Figure 3: Transition Time Figure 4: Shut Down Action
F igure 5: Breakdown Voltage Vs. Temperature Figure 6: Typical Frequency Variat ion
Figure 1: VDD Regulati on Point Figure 2: Undervoltage Lockout
ICOMP
ICOMPHI
ICOMPLO VDDreg
0VDD
Slope =
Gm in mA/V
FC00150
VDDon
IDDch
IDD0
VDD
VDDoff
VDS= 3 5 V
Fsw = 0
IDD
VDDhyst
FC00170
ID
VDS
t
t
tf tr
10% Ipeak
10% V D
90% V D
FC00160
VCOMP
VOSC
ID
t
tDISsu
t
t
ENABLE DISABLEENABLE
VCOMPth
FC00060
Temperature (°C)
FC00180
0 20406080100120
0.95
1
1.05
1.1
1.15
BVDSS
(Normalized)
Temperat ure ( °C)
0 20406080100120140
-5
-4
-3
-2
-1
0
1FC00190
(%)
VIPer100/SP - VIPer100A/ASP
7/23
Figur e 7: Start-Up Waveforms
Figure 8: Overtemperature Protection
SC10191
TJ
Ttsd-Thyst
Ttsc
Vdd
Vddon
Vddoff
Id
Vcomp
t
t
t
t
8/23
VIPer100/SP - VIPer100A/ASP
Figur e 9: Oscillator
1
Rt
Ct
OSC
VDD
~360
CLK
FC00050
1 2 3 5 10 20 30 50
30
50
100
200
300
500
1,000
Rt (k)
Frequency (kHz)
Oscillator frequency vs Rt and Ct
Ct = 1.5 nF
Ct = 2.7 nF
Ct = 4.7 nF
Ct = 10 nF
FC00030FC00030
For Rt >1.2K
and
Ct 15nF if FSW 40KHz
FSW 2.3
RtCt
------------ 1550
Rt150
----------------------


=
C
t
Fsw
40kHz
15nF
22nF
Forbidden area
Forbidden area
Ct(nF) = Fsw(kHz)
880
VIPer100/SP - VIPer100A/ASP
9/23
Figure 10: Error Amplifier Frequency Response
Figure 11: Error Amplifier Phase Response
1
0.001 0.01 0.1 1 10 100 1,000
(20)
0
20
40
60
Frequency (kHz)
Voltage Gain (dB)
RCOMP = +
RCOMP = 27 0k
RCOMP = 82k
RCOMP = 27 k
RCOMP = 12 k
FC00200
0.001 0.01 0.1 1 10 100 1,000
(50)
0
50
100
150
200
Frequenc y (kHz)
Phase (°)
RCOMP = +
RCOMP = 270k
RCOMP = 82k
RCOMP = 27k
RCOMP = 12k
FC00210
10/23
VIPer100/SP - VIPer100A/ASP
Figure 12: Avalanche Test Circuit
1
FC00195
U1
VIPer100
13V
OSC
COMP SOURCE
DRAINVDD
-
+
23
54
1
R3
100
R2
1k
BT2
12V
C1
47uF
16V
Q1
2 x STHV102FI in parallel
R1
47
L1
1mH
GENERATOR INPUT
500us PULSE
BT1
0 to 20V
11/23
VIPer100/SP - VIPer100A/ASP
1
Figure 13: Off Line Power Supply With Auxiliary Supply F eedback
Figure 14: Off Line Power Supply With Optocoupler Feedback
AC IN +Vcc
GND
F1
BR1
D3
R9
C1
R7
C4
C2
TR2
R1
C3
D1
D2
C10
TR1
C9
C7
L2
R3
C6
C5
R2
U1
VIPer100
-
+
13V
OSC
COMP SOURCE
DRAINVDD
FC00081
C11
FC00091
AC IN
F1
BR1
D3
R9
C1
R7
C4
C2
TR2
R1
C3
D1
D2
C10
TR1
C9C7
L2 +Vcc
GND
C8
C5
R2
U1
VIPer100
U2
R4
R5
ISO1 R6
R3
C6
-
+
13V
OSC
COMP SOURCE
DRAINVDD
C11
12/23
VIPer100/SP - VIPer100A/ASP
OPERATION DESCRIPTION:
CURRENT MODE TOPOLOGY:
The current mode control method, like the one
int egrated i n the VI Per100 /100A us es two c ontrol
loo ps - an i nner curr ent contro l loop an d an outer
loop for voltage control. When the Power
MOSFET output transistor is on, the inductor
current (primary side of the transformer) is
monitored with a SenseFET technique and
converted into a voltage VS proportional to this
current. When VS reaches VCOMP (the amplified
output voltage erro r) the powe r swi tch i s sw itched
off. Thus, the outer voltage control loop defines
the level at which the inner loop regulates peak
cu rrent thro ugh the pow er swi tch and the p rimary
windi ng of the transformer.
Excellent open loop D.C. and dynamic line
regulation is ensured due to the inherent input
voltage feedforward characteristic of the current
mode control. This results in an improved line
regulation, instantaneous correction to line
changes and better stability for the voltage
regulation loop.
Current mode topology also ensures good
limita tion in the case of short circui t. Du ring a fir st
phase the output current increases slowly
followi ng the dynamic of the regulation loop. Then
it reaches the maximum limitation current
int erna lly set an d f inal ly s to ps bec au se t he pow er
supply on VDD is no longer correct. For specific
applications the maximum peak current internally
set can be overridden by externally limiting the
vol tage excursion on the COMP pin. An integrated
blanking filter inhibits the PWM comparator output
for a short time after the integrated Power
MOSFET is switched on. This function prevents
anomalous or premature termination of the
switching pulse in the case of current spikes
ca used by pr i mary si de capaci tan ce or sec o ndar y
side rectifier reverse recovery time.
STAND- BY MODE
Stand-by operation in nearly open load condition
automatically leads to a burst mode operation
allowing voltage regulation on the secondary side.
The transition from normal operation to burst
mode oper ati on happe ns for a power PSTBY given
by :
Where:
LP is the primary inductance of the transformer.
FSW is the normal switching frequency.
ISTBY is the minimum controllable current,
corresponding to the minimum on time that the
device is able to provide in normal operation. This
current can be computed as :
tb + td is the sum of the blanking time and of the
propagation time of the internal curr ent sense and
compa rator, and represents r oughly th e minimu m
on time of the device. Note that PSTBY may be
affected by the efficiency of the converter at low
load, and must include the power drawn on the
prim ary auxiliary voltage.
As soon as the power goes below this limit, the
auxiliary secondary voltage starts to increase
above the 13V regulation level forcing the output
voltage of the transconductance amplifier to low
state (VCOMP < VCOMPth). This situation leads to
the shutdown mode where the power switch is
maintained in the off state, resulting in missing
cycles and zero duty cycle. As soon as VDD gets
back to the regulation level and the VCOMPth
threshold is reached, the device operates again.
The above cycle repeats indefinitely, providing a
burst mode of which the effective duty cycle is
much lower than the minimum one when in normal
operation. The equivalent switching frequency is
also lower than the normal one, leading to a
reduced consumption on the input mains lines.
This mode of operation allows the VIPer100/100A
to meet the new Germa n "Blue Angel" Norm with
less than 1W total power consumption for the
system when working in stand-by. The output
voltage remains regulated around the normal
level, with a low frequency rippl e corresponding to
the burst mode. The amplitude of this ripple is low,
because of the output capacitors and of the low
output current drawn in such conditions.The
normal operation resumes automatically when the
power get back to higher levels than PSTBY.
HIGH VOLTAGE START-UP CURRENT
SOURCE
An integrated high voltage current source provides
a bias current from the DRAIN pin during the start-
up phase. This current is partially absorbed by
internal control circuits which are placed into a
standby mode with reduced consumption and also
provided to the external capacitor connected to the
VDD pin. As soon as the voltage on this pin
reaches the high voltage threshold VDDon of the
UVLO logic, the device turns into active mode and
starts switching.
PSTBY 1
2
--- LPI2STBYFSW
=
ISTBY tbtd
+
()V
IN
LP
--------------------------------
=
13/23
VIPer100/SP - VIPer100A/ASP
The start up current generator is switched off, and
the c onver ter sho ul d nor mall y pro vid e the ne eded
current on the VDD pin through the auxiliary
winding of the transformer, as shown on figure 15.
In case of abnor mal condition where the auxiliary
winding is unable to provide the low voltage supply
current to the VDD pin (i.e. short circuit on the
output of the converter), the external capacitor
discharges itself down to the low threshold voltage
VDDoff of the UV LO logi c, an d the de v ice get ba c k
to the inactive state where the internal circuits are
in standby mode and the start up current source is
ac tivated. T he c onve rter en ters a en dl ess s tart up
cycle, with a start-up duty cycle defined by the
ratio of charging current towards discharging when
the VIPer100/100A tries to start. This ratio is fixed
by design to 2 to 15, which gives a 12% start up
duty cycle while the power d issipation at start up is
approximately 0.6 W, for a 230 Vrms input voltage.
This low value of star t-up dut y cycle prevents the
stress of the output rectifiers and of the
transformer when in short circuit.
The ex ter nal ca pac itor CVDD on the VDD pin mu st
be sized according to the time needed by the
converter to start up, when the device starts
switching. This time tSS depends on many
parameters, among which transformer design,
output capacitors, soft start feature and
compensation network implemented on the COMP
pin. The following formula can be used for defining
the minimum capacitor needed:
where:
IDD is the consumption current on the VDD pin
when switching. Refer to specified IDD1 and IDD2
values.
tSS is the start up time of the converter when the
device begins to switch. Worst case is generally at
full load.
VDDhyst is the voltage hysteresis of the UVLO
logic. Refer to the minimum specified value.
Soft start feature can be implemented on the
COMP pin through a simple capacitor which will be
also used as the compensation network. In this
case, the regu la tion lo op bandwidth is ra ther low,
because of the large value of this capacitor. In
case a large regulation loop bandwidth is
mandatory, the schematics of figure 16 can be
used. It mixes a high performance compensation
network together with a separate high value soft
start cap acitor. Both soft sta rt time and regul ation
loop bandwidth can be adjusted separately.
If the d evice is intentionally shut down by putting
the COMP pin to ground, the device is also
performing start-up cycles, and the VDD voltage is
oscillating between VDDon and VDDoff.
This voltage can be used for supplying external
functions, provided that their consumption doesn’t
exceed 0.5mA. Figure 17 shows a typical
application of this function, with a latched shut
down. Once the "Shutdown" signal has been
activated , the de vice re mains in the off state unti l
the input voltage is removed.
CVDD IDDtSS
VDDhyst
--------------------------
>
Figure 15: Behaviour of the high voltage current source at start-up
Ref.
UNDERVOLTAGE
LOCK OUT LOGIC
15 mA
1 mA
3 mA
2 mA
15 mA
VDD DRAIN
SOURCE
VIPer100
Auxiliary primary
winding
VDD
t
VDDoff
VDDon
Start up duty cycle ~ 12%
CVDD
FC00100
14/23
VIPer100/SP - VIPer100A/ASP
TRANSCONDUCTANCE ERROR AMPLIFIER
The VIPer100/1 00A includes a tra nsconductance
error amplifier. Transconductance Gm is the
change in output current (ICOMP) versus change in
input voltage (VDD). T hus:
The output im pedance ZCOMP at the output of this
amplifier (COMP pin) can be defined as:
This last equation shows that the open loop gain
AVOL can be related to Gm and ZCOMP:
AVOL = Gm x ZCOMP
where Gm value for VIPer100/100A is 1.5 mA/V
typically.
Gmis well defined by specification, but ZCOMP and
therefore AVOL are subject to large tolerances. An
impedance Z can be connected between the
COMP pin and ground in order to define more
accurately the transfer function F of the error
amplifier, according to the followi ng equation, very
similar to the one above:
F(S) = Gm x Z(S)
The error amplifier frequency response is reported
in figure 10 for different values of a simple
resistance connected on the COMP pin. The
unl oaded tr ansconduc tance er ror amp lifier s hows
an inte r na l Z COMP of about 330 K. More complex
impedance can be connected on the COMP pin to
achieve different compensation laws. A capacitor
will provide an integrator function, thus eliminating
the DC static error, and a resistance in series
leads to a fl at gain at hi gher fre quency, insuri ng a
correct phase margin. This configuration is
illustrated on fi gure 18.
As show n in figu re 18 an a dditiona l noise filter ing
capacitor of 2.2 nF is generally needed to avoid
any high frequency interference.
It can be also interesting to implement a slope
compensation when working in continuous mode
with duty cycle higher than 50% . Figur e 19 shows
such a configuration. Note that R1 and C2 build
the classical compensation network, and Q1 is
injecting the slope compensation with the correct
polarity from the oscillator sawtooth.
EXT ERNAL CLOCK SYNCH RONIZATION:
The OSC pin provides a synchronisation
capability, when connected to an external
frequency source. Figure 20 shows one possible
schematic to be adapted depending the specific
needs. If the proposed schematic is used, the
pulse duration must be kept at a low value (500ns
is sufficient) for minimizing consumption. The
optocoupler must be able to provide 20mA through
the optotransistor.
PRI MARY PEAK CURRENT LIMITATION
The primary IDPEAK current and, as resulting
effect, the output power can be limited using the
simple circuit show n in figure 21. The circuit based
on Q1, R1 and R2 clamps the voltage on the
GmICOMP
VDD
------------------------
=
ZCOMP VCOMP
ICOMP
--------------------------- 1
m
G
--------- VCOMP
VDD
---------------------------
×
==
Figure 16: Mixed Soft Start and Compensation Figure 17: Latched Shut Down
AUXILIARY
WINDING
-
+
13V
OSC
COMP SOURCE
DRAINVDD
U1
VIPER100
R1
C1 +C2
D1
R2
R3
D2
D3
+C3
FC00131
C4
-
+
13V
OSC
COMP SOURCE
DRAINVDD
VIPER100
Shutdown
U1
Q1
Q2
R1
R2R3
R4 D1
FC00110
15/23
VIPer100/SP - VIPer100A/ASP
COMP pin in order to limit the primary peak
current of the device to a value:
where:
The su ggeste d value for R1+R2 is in the range of
220K.
OVER-TEMPERATURE PROTECTION:
Over-temperature protection is based on chip
temperature sensing. The minimum junction
temperature at which over-temperature cut-out
occurs is 140ºC while the typical value is 170ºC.
The device is automatically restarted when the
junction temperature decreases to the restart
temperature thres ho ld that i s t ypi cal ly 40ºC below
the shutdown value (see figure 8).
IDPEAK VCOMP 0.5
HID
-------------------------------------
=
VCOMP 0.6 R1R2
+
R2
----------------------
×
=
Figure 18: Typical Compensation Network
Figure 20: External Clock Sinchronisation
Figure 19: Slope Compensation
Figure 21: Current Limitation Circuit Example
-
+
13V
OSC
COMP SOURCE
DRAINVDD
VIPER100
U1
R1
C1
FC00121
C2
FC00141
-
+
13V
OSC
COMP SOURCE
DRAINVDD
VIPER100
R1R2
Q1
C2
C1 R3
U1
C3
-
+
13V
OSC
COMP SOURCE
DRAINVDD
U1
VIPER100
10 k
FC00220
-
+
13V
OSC
COMP SOURCE
DRAINVDD
VIPER100
U1
R1
R2
Q1
FC00240
16/23
VIPer100/SP - VIPer100A/ASP
Figure 22: Input Volta ge Surges Protecti on
ELECTRICAL O VER STRESS RUGGEDNESS
The VIPer may be submitted to electrical over
stress caused by violent input voltage surges or
lightning. Following the enclosed Layout
Considerations chapter rules is the most of the
time sufficient to prevent catastrophic damages,
however in some cases the voltage surges
coupled throug h the transformer auxiliary winding
can overpass the VDD pin absolute maximum
rating voltag e value. S uch ev ents may trigg er the
VDD internal protection circuitry which could be
damaged by the strong discharge current of the
VDD bulk ca pac itor . T he si mp le R C fi lter show n in
figure 22 can be implemented to improve the
application immunity to such surges.
C1
Bulk capacitor
D1
R1
(Optional)
C2
22nF
Auxilliary winding
13V
OSC
COMPSOURCE
DRAIN
VDD
-
+
VIPerXX0
R2
39R
17/23
VIPer100/SP - VIPer100A/ASP
1
Figure 23: Rec omme nded Layout
LAYOUT CONSIDERATIONS
Some simple rules insure a correct running of
swit ching pow er suppli es. They m ay be classi fied
into two categories:
- To minimise power loops: the way the switched
power current must be carefully analysed and
the corresponding paths must present the
smallest inner loop area as possible. This
avoids radiated EMC noises, conducted EMC
noises by magnetic coupling, and provides a
better efficiency by eliminating parasitic
inductances, especially on secondary side.
- To use different tracks for low level signals and
power ones. T he interfe rence s due to a mi xing
of signal and power may result in instabilities
and/or anomalous behaviour of the device in
case of violent power surge (Input overvoltages,
output short circuits...).
In case of VIPer, these rules apply as shown on
figure 23. The loops C1-T1-U1, C5-D2-T1, C7-D1-
T1 must be minimised. C6 must be as close as
possible from T1. The signal components C2,
ISO1, C3 and C4 are using a dedicated track to be
connected directly to the source of the device.
T1
U1
VIPerXX0
13V
OSC
COMP SOURCE
DRAINVDD
-
+
C4
C2
C5
C1
D2
R1
R2
D1
C7
C6
C3
ISO1
)URPLQSXW
GLRGHVEULGJH
7RVHFRQGDU\
ILOWHULQJDQGORDG
FC00500
18/23
VIPer100/SP - VIPer100A/ASP
DIM. mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 3.35 3.65 0.132 0.144
A (*) 3.4 3.6 0.134 0.142
A1 0.00 0.10 0.000 0.004
B 0.40 0.60 0.016 0.024
B (*) 0.37 0.53 0.014 0.021
C 0.35 0.55 0.013 0.022
C (*) 0.23 0.32 0.009 0.0126
D 9.40 9.60 0.370 0.378
D1 7.40 7.60 0.291 0.300
E 9.30 9.50 0.366 0.374
E2 7.20 7.60 0.283 300
E2 (*) 7.30 7.50 0.287 0.295
E4 5.90 6.10 0.232 0.240
E4 (*) 5.90 6.30 0.232 0.248
e 1.27 0.050
F 1.25 1.35 0.049 0.053
F (*) 1.20 1.40 0.047 0.055
H 13.80 14.40 0.543 0.567
H (*) 13.85 14.35 0.545 0.565
h 0.50 0.002
L 1.20 1.80 0.047 0.070
L (*) 0.80 1.10 0.031 0.043
α
α (*)
PowerSO-10 MECHA NICAL DATA
(*) Muar only POA P013P
DETAIL "A"
PLANE
SEATING
α
L
A1
F
A1
h
A
D
D1
= =
= =
E4
0.10 A
C
A
B
B
DETAIL "A"
SEATING
PLAN E
E2
10
1
eB
HE
0.25
P095A
19/23
VIPer100/SP - VIPer100A/ASP
11
DIM. mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 4.30 4.80 0.169 0.189
C 1.17 1.37 0.046 0.054
D 2.40 2.80 0.094 0.11
E 0.35 0.55 0.014 0.022
F 0.60 0.80 0.024 0.031
G1 4.91 5.21 0.193 0.205
G2 7.49 7.80 0.295 0.307
H1 9.30 9.70 0.366 0.382
H2 10.40 0.409
H3 10.05 10.40 0.396 0.409
L 15.60 17.30 6.14 0.681
L1 14.60 15.22 0.575 0.599
L2 21.20 21.85 0.835 0.860
L3 22.20 22.82 0.874 0.898
L5 2.60 3 0.102 0.118
L6 15.10 15.80 0.594 0.622
L7 6 6.60 0.236 0.260
M 2.50 3.10 0.098 0.122
M1 4.50 5.60 0.177 0.220
R 0.50 0.02
V4 90° (typ)
Diam 3.65 3.85 0.144 0.152
P023H3
PENTAW ATT HV MECHANICAL DATA
20/23
VIPer100/SP - VIPer100A/ASP
1
A
C
H2
H3
H1
L5
DIA
L3
L6
L7
F
G1
G2
LL1
D
R
M
M1
E
Resin bet w een
leads
V4
DIM. mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 4.30 4.80 0.169 0.189
C 1.17 1.37 0.046 0.054
D 2.40 2.80 0.094 0.110
E 0.35 0.55 0.014 0.022
F 0.60 0.80 0.024 0.031
G1 4.91 5.21 0.193 0.205
G2 7.49 7.80 0.295 0.307
H1 9.30 9.70 0.366 0.382
H2 10.40 0.409
H3 10.05 10.40 0.396 0.409
L 16.42 17.42 0.646 0.686
L1 14.60 15.22 0.575 0.599
L3 20.52 21.52 0.808 0.847
L5 2.60 3.00 0.102 0.118
L6 15.10 15.80 0.594 0.622
L7 6.00 6.60 0.236 0.260
M 2.50 3.10 0.098 0.122
M1 5.00 5.70 0.197 0.224
R 0.50 0.020
V4 90° 90°
Diam. 3.70 3.90 0.146 0.154
PENTAWATT HV 022Y (VERTICAL HIGH PITCH) MECHANICAL DATA
21/23
VIPer100/SP - VIPer100A/ASP
1
PowerSO-10 SUGGESTED PAD LAYOUT
1
TAPE AND RE EL SHIPMENT ( suffix “13TR”)
REEL DIMENSIONS
All dimensions are in mm.
Base Q. ty 600
Bulk Q.ty 600
A (max) 330
B (min ) 1.5
C (± 0. 2) 13
F20.2
G (+ 2 / -0) 24.4
N (min ) 60
T (m ax) 30.4
TAPE DIM ENSI ONS
According to Electronic Industries Association
(EIA) St andard 481 rev. A, Feb. 198 6
A ll dime nsions a re in mm.
Tape width W 24
Tape Hole Spacin g P0 (± 0.1) 4
Com ponen t Spacin g P 24
Hole Diameter D (± 0.1/-0) 1.5
Hole Diamete r D1 (m in) 1.5
Hole Position F (± 0.05) 11.5
Com partment Dept h K (max) 6.5
Hole Spacing P1 0.1) 2
Top
cover
tape
End
Start
No componentsNo components Components
500mm min
500mm min
Empty components pockets
saled with cover tape.
User direction of feed
6.30
10.8 - 11
14.6 - 14.9
9.5
1
2
3
4
51.27
0.67 - 0.73
0.54 - 0.6
10
9
8
7
6
B
A
C
All di m ens ions are in m m .
Base Q.ty Bulk Q.ty Tube length (± 0.5) A B C (± 0 .1)
Casablanca 50 1000 532 10.4 16.4 0.8
Muar 50 1000 532 4.9 17.2 0.8
TUBE SHIPMENT (no suffix)
C
A
B
MUARCASABLANCA
VIPer100/SP - VIPer100A/ASP
22/23
1
PENTAWATT HV TUBE SHIPMENT (no suffix)
All dimensions are in mm.
Base Q.ty 50
Bulk Q.ty 1000
Tube length (± 0.5) 532
A18
B33.1
C (± 0.1) 1
C
B
A
VIPer100/SP - VIPer100A/ASP
23/23
1
Information fur nished is believ ed to be a c c ur ate and r eliab le. Howev er, STMicroelectr onics assumes no res ponsibil ity for the cons equences
of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is
gran ted by implication o r otherwi s e under any pa tent or patent rights of STMicroelectr onics. Spec ifications mentio ned in this publication are
subj ec t to change without notice. This p ublicat ion supersedes an d r eplaces all information previously suppl ied. STM icroelectr on ics prod uc ts
are not authorized for use as crit ical components in life support devices or systems without expr ess written approval of STMicroelectronics.
The ST logo is a trademark of STMicroelectro nic s
2003 STMicroelectronics - Prin ted in ITALY- All Ri ghts Re served.
STMicroelectronics GROUP OF COMPANI ES
Aust r alia - Br azil - Canada - Ch ina - Finland - France - Germany - Hong K ong - India - Israel - Italy - Jap an - M alaysia -
Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com