Voting resources, early voting, and poll worker information - VOTE. ... Adafruit is open and shipping.
WIRELESS / RFID / NFC / ADAFRUIT ST25DV16K I2C RFID EEPROM BREAKOUT - STEMMA QT / QWIIC
1
ADD TO CART
Adafruit ST25DV16K
I2C RFID EEPROM
Breakout - STEMMA
QT / Qwiic
PRODUCT ID: 4701
28 IN STOCK
Order now to ship today
1-9
10-99
100+
ADD TO WISHLIST
DESCRIPTION
TECHNICAL DETAILS
Shop Learn Blog Forums LIVE! Adabox IO Sign In 0
Products
Gift Ideas
What's New
DESCRIPTION
This RFID tag is really unique: it works with mobile phones just like other RFID tags, but you can
reprogram it over I2C. The tag shows up as an ISO/IEC 15693 (13.56MHz) chip which is
readable by phones and tablets. This could be interesting in situations where you want a tag
that can be re-written dynamically when connected to a controller. For example, we did a test
where we had a microcontroller write different URLs a few seconds apart, and the mobile
phone detected the different URLs one after the other.
Note that the most popular hobby RFID reader/writer chips like the PN532 do not support
ISO15693 so you cannot use those to read the ST25DV tag once programmed! We used both
Apple and Android phones with success to read the tags.
According to the datasheet, one can even use it as a 'I2C to RFID' transfer system to wirelessly
send and receive data from mobile devices (you'll need to write a custom app for that kind of
project, though).
ST has written a handy library that you can easily use to write NFC URLs to the chip over I2C.
You cannot use an Arduino UNO (ATmega328p) with the ST25DV library, there's not
enough RAM. Please use a Metro M0 or other SAMD chip (or better) to communicate with the
ST25DV. There's no Python or CircuitPython library for this chip at this time, only Arduino.
To make connections easy, our breakout contains an ST25DV04 chip, support circuitry and
even a PCB trace antenna. There's standard 0.100”/ 2.54mm pitch headers for use with a
breadboard. Should you wish to avoid soldering, the breakout also includes our Stemma QT
connectors (SparkFun Qwiic compatible). Using these handy connectors you can simply plug in
the sensor and get rolling with your project.
TECHNICAL DETAILS
#NewProducts 8/6/2020 Feat. #Adafruit #ST25DV16K I2C …
I2C interface
Two-wire I2C serial interface supports 1MHz protocol
Uses multiple I2C addresses 0x2D, 0x53 (user memory) and 0x57 (system memory)
Single supply voltage: 1.8V to 5.5V
Multiple byte write programming (up to 256 bytes)
Contactless interface
Based on ISO/IEC 15693
NFC Forum Type 5 tag certified by the NFC Forum
Supports all ISO/IEC 15693 modulations, coding, sub-carrier modes and data rates
Custom fast read access up to 53 Kbit/s
Single and multiple blocks read (same for Extended commands)
Single and multiple blocks write (up to 4) (same for Extended commands)
Internal tuning capacitance: 28.5 pF
Memory
16-kbits of EEPROM
I2C interface accesses bytes
RF interface accesses blocks of 4 bytes
Write time:
From I2C: typical 5ms for 1 byte
LEARN
MAY WE ALSO SUGGEST...
From RF: typical 5ms for 1 block
Data retention: 40 years
Write cycles endurance:
1 million write cycles at 25 °C
600k write cycles at 85 °C
500k write cycles at 105 °C
400k write cycles at 125 °C
Fast transfer mode
Fast data transfer between I2C and RF interfaces
Half-duplex 256-byte dedicated buffer
Energy harvesting
Analog output pin to power external components
Data protection
User memory: 1 to 4 configurable areas, protectable in read and/or write by three 64-bit
passwords in RF and one 64-bit password in I2C
System configuration: protected in write by a 64-bit password in RF and a 64-bit password
in I2C
Product Dimensions: 31.7mm x 25.3mm x 4.6mm / 1.2" x 1.0" x 0.2"
Primary Guide: Adafruit ST25DV16K I2C RFID EEPROM
Breakout
Program RFID over I2C!
