Automotive Relays PCB Double Relays Double Micro Relay K (THT - THR) Small power relay Limiting continuous current 20A at 85C Minimal weight Low noise operation Wave (THT) and reflow (THR/pin-in-paste) solderable versions For single version refer to Single Micro Relay K Typical applications Door lock, heated front/rear screen, lamps front/rear/fog light, interior lights, seat control, sun roof, window lifter, wiper control. 086C/R2_fcw1b Contact Data (continued) Contact Data > 5x106 ops. Mechanical endurance Contact arrangement 2 form C, 2 CO Rated voltage 10/12VDC Rated current1)NO/NC 30A/25A Limiting continuous current1) 23C 30/25A 85C 20/15A 105C 15/10A Limiting making current 40A2) Limiting breaking current 30A Contact material AgSnO2 Min. contact load 1A at 5VDC3) Initial voltage drop at 10A, typ./max. 30/300 mV Operate/release time typ. 3/1.5ms4) Electrical endurance -40C, +25C, +85C and 14 VDC, form C (CO), cyclic temperature motor reverse blocked, 25A, 0.77mH >1x105 ops. wiper 25A make/5A break, generator peak -20A on NC, L=1.0mH >1x106 ops. form A contact (NO), cyclic temperature resistive 20A >1x105 ops. 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 25cm2 (double layer 105m) copper area. Connecting cable cross section 6 mm2.Boundary conditions: 180C coil temperature;130C solder joint. Only one relay energized. 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 4) Measured at nominal voltage without coil suppression unit. A low resistive suppression device in parallel to the relay coil increases the release time and reducesthe lifetime caused by increased erosion and/or higher risk of contact tack welding. Coil Data Rated coil voltage Coil versions, DC coil Coil Rated Operate code voltage voltage VDC VDC 001 12 6.9 002 10 5.7 12VDC Release voltage VDC 1.5 1.25 Coil resistance 10% 254 181 Rated coil power mW 567 552 All figures are given for coil without pre-energization, at ambient temperature +23C. Coil operating range Max. DC load breaking capacity 100 300 Max. Switching Voltage in VDC 0W 42 0W W 0W 20 10 30 250 Umax 200 150 curve I 100 curve II 50 Uop (E=0V) 0 -40 10 0.1 1 10 Switching Current in A -20 0 20 40 60 Ambient temperature in C 80 100 120 100 Does not take into account the temperature rise due to the contact current E = pre-energization Load limit curve I: safe shutdown, arc extinguishes during transit time. Load limit curve II: safe shutdown, no stationary arc. Load limit curves measured with low inductive resistors verified for 1000 switching events. 07-2017, Rev. 0717 www.te.com (c) 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 1 Automotive Relays PCB Double Relays Double Micro Relay K (THT - THR) (Continued) Terminal Assignment Bottom view on solder pins Insulation Data 500VACrms 500VACrms 2 form C, 2 CO 13 14 15 Other Data EU RoHS/ELV compliance compliant Ambient temperature -40 to +105C Cold storage, IEC 60068-2-1 1000h; -40C Dry heat, IEC 60068-2-2 1000h; +125C Climatic cycling with condensation, EN ISO 6988 20 cycles, storage 8/16 h Temperature cycling (shock), IEC 60068-2-14, Na 100 cycles; -40/+125C Temperature cycling, IEC 60068-2-14, Nb 35 cycles; -40/+125C Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles 25C/55C/93%RH Damp heat constant, IEC 60068-2-3 method Ca 56 days 40C/95%RH Degree of protection THT: RT III (61810) THR: RT II (61810) Corrosive gas, IEC 60068-2-17: THT Qc, method 2, 1min, 70C IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional) IEC 60068-2-6 (sine sweep) 10 to 500Hz; 6g5) Shock resistance (functional) IEC 60068-2-27 (half sine) 6ms, up to 30g5) Terminal type PCB:THT, THR Weight approx. 8g (0.28oz) Solderability (aging 3: 4h/155C) THT, IEC 60068-2-20 Ta, method 1, hot dip 5s, 215C Resistance to soldering heat THT, IEC 60068-2-20 Tb, method 1A, hot dip 10s, 260C, with thermal screen Resistance to soldering heat THR, IEC 60068-2-58 260C; preheating min 130C Storage conditions according IEC 60068-16) Packaging unit 990 pcs. 22 11 21 12 25 24 23 86dtw_ab Dimensions Double Micro Relay THT 23,6 0,2 6,2 0,1 2,5 0,2 7,65 0,2 0,4 0,1 9,9 0,2 0,6 0,2 2,8 0,2 *) Initial dielectric strength between open contacts between contact and coil 12,9 0,3 A 0,95 0,2 5) Depending on mounting position: no change in the switching state >10s. 6) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ *) Additional tin tops max. 1 mm 86dtw_se View of the Terminals Bottom view on solder pins 10x 10x 0,5 0,4 A B A 0,5 0,4 A C A 11,67 0,97 12,67 19,67 20,17 0,97 12 0,15 24 25 0,15 0,25 21 2,1 11 22 0,25 14 0,48 0,15 15 4x 0,25 0,25 7,26 23 1,4 24 25 2,1 12 21 13 10,2 11 22 1,4 0,06 15 3,6 1,37 14 13 5,87 0,15 3,7 0,25 0,97 0,15 0,97 0,15 0,25 0,25 3,4 4,5 10,26 0,5 +0,05 4x 0 1,72 6,66 B 0,48 0,5 3 C 1 0,1 5 1,2 + 0 0 ,05 6x 8,5 7,5 23 4,5 3,4 0,25 0,25 0,15 3,7 0,25 5,87 0,15 Remark: Positional tolerances according to DIN EN ISO 5458 2 07-2017, Rev. 0717 www.te.com (c) 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. Automotive Relays PCB Double Relays Double Micro Relay K (THT - THR) (Continued) 0,2 0,6 0,2 2,5 0,2 0,6 0,2 0,2 6,2 23,6 0,1 0,2 6,2 0,1 0,2 0,210,2 10,2 0,1 0,7 0,7 0,17,65 0,2 2) 2,5 2,5 0,1 0,1 2,5 23,6 7,65 0,2 2) Dimensions Double Micro Relay THR A A 12,9 0,3 0,2 0,95 12,9 0,3 0,95 0,2 View of the Terminals Bottom view on solder pins 10x 10x 0,5 0,5 A B A B 0,4 0,4 A A 10x 10x 0,5 0,5 A C A C 0,4 0,4 A A 07-2017, Rev. 0717 www.te.com (c) 2017 TE Connectivity. 11,6711,67 12,6712,67 19,6719,67 20,1720,17 Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. 12 12 0,15 0,15 0,97 0,97 23 23 0,15 0,25 24 24 0,25 25 25 2,1 11 21 21 2,1 1,4 11 22 22 0,48 14 14 1,4 0,15 0,48 0,25 1 0,1 5 1 0,1 5 4x 15 15 4x 0,15 1,4 0,25 0,48 0,15 0,48 0,25 23 23 0,25 0,25 24 24 2,1 25 25 1,4 2,1 12 12 11 21 21 13 13 10,26 11 22 22 7,26 10,2 14 14 3,6 6,66 15 15 7,26 6,66 13 13 0,15 0,15 5,87 5,87 0,25 0,25 3,7 3,7 0,15 0,15 0,97 0,97 0,15 0,15 0,97 0,97 0,25 0,25 3,4 3,4 0,25 0,25 4,5 4,5 3 3,6 1,37 1,72 1,72 10,26 10,2 0,5 +0,05 4x 0 +0,05 0,5 0 4x 1,37 B 0,5 0,5 0,06 B C 0,06 C 3 8,5 8,5 7,5 7,5 1,2 + 0 0 ,05 1,2 + 6 0,0 x 0 5 6x View of Stand-Offs Bottom view on solder pins 0,25 0,25 4,5 4,5 0,25 0,25 3,4 3,4 0,15 0,15 0,97 0,97 0,25 0,25 3,7 3,7 0,15 0,15 5,87 5,87 Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 3 Automotive Relays PCB Double Relays Double Micro Relay K (THT - THR) (Continued) Product code structure Typical product code V23086 -C 20 01 -A 4 03 Type V2086 Micro Relay K (THT-THR) Terminal and enclosure C PCB version THT, sealed Design 20 Double relay (THT) Coil 01 Standard Contact type A Single contact Contact material index 4 AgSnO2 standard Contact arrangement index 03 form C (CO) Product code V23086-C2001-A403 V23086-R2801-A403 V23086-R2802-A803 Terminal/Encl. PCB THT, imm., clean PCB THR, vented R PCB version THR, vented 28 Double relay (THR) 02 Sensitive 8 Wiper load Design Double relay Coil Standard Contact Cont. material Single Sensitive AgSnO2 Arrangement 2 form C, 2 CO (standard) 2 form C, 2 CO (wiper load) Part number 0-1413009-9 6-1414920-1 8-1414964-5 This list represents the most common types and does not show all variants covered by this datasheet. Other types on request. 4 07-2017, Rev. 0717 www.te.com (c) 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change.