07-2017, Rev. 0717
www.te.com
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
1
■ Small power relay
■ Limiting continuous current 20A at 85°C
■ Minimal weight
■ Low noise operation
■ Wave (THT) and reflow (THR/pin-in-paste) solderable versions
■ For single version refer to Single Micro Relay K
Typical applications
Door lock, heated front/rear screen, lamps front/rear/fog light, interior
lights, seat control, sun roof, window lifter, wiper control.
Contact Data
Contact arrangement 2 form C, 2 CO
Rated voltage 10/12VDC
Rated current1) NO/NC
30A/25A
Limiting continuous current1)
23°C 30/25A
85°C 20/15A
105°C 15/10A
Limiting making current 40A2)
Limiting breaking current 30A
Contact material AgSnO2
Min. contact load 1A at 5VDC3)
Initial voltage drop at 10A, typ./max. 30/300 mV
Operate/release time typ. 3/1.5ms4)
Electrical endurance
-40°C, +25°C, +85°C and 14 VDC,
form C (CO), cyclic temperature
motor reverse blocked, 25A, 0.77mH >1x105 ops.
wiper 25A make/5A break,
generator peak -20A on NC, L=1.0mH >1x106 ops.
form A contact (NO), cyclic temperature
resistive 20A >1x105 ops.
Contact Data (continued)
Mechanical endurance > 5x106 ops.
1) Measured on 70x70x1.5mm epoxy PCB FR4 with 25cm2 (double layer 105μm)
copper area. Connecting cable cross section 6 mm2.Boundary conditions: 180°C coil
temperature;130°C solder joint. Only one relay energized.
2) The values apply to a resistive or inductive load with suitable spark suppression and at
maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum
3s for a make/break ratio of 1:10.
3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
4) Measured at nominal voltage without coil suppression unit. A low resistive suppression
device in parallel to the relay coil increases the release time and reducesthe lifetime
caused by increased erosion and/or higher risk of contact tack welding.
Coil Data
Rated coil voltage 12VDC
Coil versions, DC coil
Coil Rated Operate Release Coil Rated coil
code voltage voltage voltage resistance power
VDC VDC VDC Ω±10% mW
001 12 6.9 1.5 254 567
002 10 5.7 1.25 181 552
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Double Micro Relay K (THT – THR)
Automotive Relays
PCB Double Relays
Max. DC load breaking capacity
Load limit curve I: safe shutdown, arc extinguishes during transit time.
Load limit curve II: safe shutdown, no stationary arc.
Load limit curves measured with low inductive resistors verified for 1000 switching events.
0
50
100
150
200
250
300
-40-20 020406080100 120
Ambient temperature in °C
Umax
Uop (E=0V)
Does not take into account the temperature rise due to the contact current
E = pre-energization
086C/R2_fcw1b
10
100
0.11 10 100
Max. Switching Voltage in VDC
Switching Current in A
curve II
curve I
30 W
100 W
200 W
420 W
Coil operating range
07-2017, Rev. 0717
www.te.com
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
2
Automotive Relays
PCB Double Relays
Double Micro Relay K (THT – THR) (Continued)
Insulation Data
Initial dielectric strength
between open contacts 500VACrms
between contact and coil 500VACrms
Other Data
EU RoHS/ELV compliance compliant
Ambient temperature -40 to +105°C
Cold storage, IEC 60068-2-1 1000h; -40°C
Dry heat, IEC 60068-2-2 1000h; +125°C
Climatic cycling with condensation,
EN ISO 6988 20 cycles, storage 8/16 h
Temperature cycling (shock),
IEC 60068-2-14, Na 100 cycles; -40/+125°C
Temperature cycling,
IEC 60068-2-14, Nb 35 cycles; -40/+125°C
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1 6 cycles 25°C/55°C/93%RH
Damp heat constant,
IEC 60068-2-3 method Ca 56 days 40°C/95%RH
Degree of protection
THT: RT III (61810)
THR: RT II (61810)
Corrosive gas, IEC 60068-2-17: THT Qc, method 2, 1min, 70°C
IEC 60068-2-42 10 days
IEC 60068-2-43 10 days
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep) 10 to 500Hz; 6g5)
Shock resistance (functional)
IEC 60068-2-27 (half sine) 6ms, up to 30g5)
Terminal type PCB:THT, THR
Weight approx. 8g (0.28oz)
Solderability (aging 3: 4h/155°C) THT,
IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C
Resistance to soldering heat THT,
IEC 60068-2-20 Tb, method 1A, hot dip 10s, 260°C,
with thermal screen
Resistance to soldering heat THR,
IEC 60068-2-58 260°C; preheating min 130°C
Storage conditions according IEC 60068-16)
Packaging unit 990 pcs.
5) Depending on mounting position: no change in the switching state >10μs.
6) For general storage and processing recommendations please refer to our Application
Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/
2 form C, 2 CO
Remark:
Positional tolerances according to DIN EN ISO 5458
Terminal Assignment
Bottom view on solder pins
Dimensions
Double Micro Relay THT
View of the Terminals
Bottom view on solder pins
11
12
15
13 14
24
25
23
22
21
86dtw_ab
86dtw_se
23,6 ±0,2
2,5 ±0,2
0,6 ±0,2
6,2 ±0,1
7,65 ±0,2
9,9 ±0,2
2,8 *)
±0,2
12,9
*) Additional tin tops
max. 1 mm
±0,3
0,4 ±0,1
0,95 ±0,2
A
3
3,6
12,67
8,5
6,66
0,5
11,67
10x
0,5 AC
0,4 A
19,67
7,5
10,2
10,26
11
15
12 24
13
1,72
0,5 4x
+0,05
0
6x1,2 +0,05
0
20,17
B
10x
0,5 AB
0,4 A
7,26
C
22
25
23
14
21
0,97 0,15
4,5 0,25 0,97 0,15
11
15
12 24
13
4x 10,15
3,4 0,25
3,7 0,25
22
25
23
14
21
0,48 0,15
5,87 0,15
4,5 0,25
3,4 0,25
0,97 0,15
0,97 0,15
3,7 0,25
5,87 0,15
0,48 0,15
2,1 0,25
2,1 0,25
1,4 0,25
1,4 0,25
1,37
0,06
07-2017, Rev. 0717
www.te.com
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
3
Double Micro Relay K (THT – THR) (Continued)
Automotive Relays
PCB Double Relays
Dimensions
Double Micro Relay THR
View of the Terminals
Bottom view on solder pins
2)2,5 0,2
10,2 0,2
0,7 0,1
23,6 0,2
0,6 0,2
2,5 0,2
6,2 0,1
7,65 0,1
A
12,9 0,3
0,95 0,2
2)2,5 0,2
10,2 0,2
0,7 0,1
23,6 0,2
0,6 0,2
2,5 0,2
6,2 0,1
7,65 0,1
A
12,9 0,3
0,95 0,2
3
3,6
12,67
8,5
6,66
0,5
11,67
10x
0,5 AC
0,4 A
19,67
7,5
10,2
10,26
11
15
12 24
13
1,72
0,5 4x
+0,05
0
6x1,2 +0,05
0
20,17
B
10x
0,5 AB
0,4 A
7,26
C
22
25
23
14
21
0,97 0,15
4,5 0,25 0,97 0,15
11
15
12 24
13
4x 10,15
3,4 0,25
3,7 0,25
22
25
23
14
21
0,48 0,15
5,87 0,15
4,5 0,25
3,4 0,25
0,97 0,15
0,97 0,15
3,7 0,25
5,87 0,15
0,48 0,15
2,1 0,25
2,1 0,25
1,4 0,25
1,4 0,25
1,37
0,06
3
3,6
12,67
8,5
6,66
0,5
11,67
10x
0,5 AC
0,4 A
19,67
7,5
10,2
10,26
11
15
12 24
13
1,72
0,5 4x
+0,05
0
6x1,2 +0,05
0
20,17
B
10x
0,5 AB
0,4 A
7,26
C
22
25
23
14
21
0,97 0,15
4,5 0,25 0,97 0,15
11
15
12 24
13
4x 10,15
3,4 0,25
3,7 0,25
22
25
23
14
21
0,48 0,15
5,87 0,15
4,5 0,25
3,4 0,25
0,97 0,15
0,97 0,15
3,7 0,25
5,87 0,15
0,48 0,15
2,1 0,25
2,1 0,25
1,4 0,25
1,4 0,25
1,37
0,06
View of Stand-Offs
Bottom view on solder pins
07-2017, Rev. 0717
www.te.com
© 2017 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
4
Automotive Relays
PCB Double Relays
Double Micro Relay K (THT – THR) (Continued)
Product code structure Typical product code V23086 -C 20 01 -A 4 03
Type
V2086 Micro Relay K (THT-THR)
Terminal and enclosure
C PCB version THT, sealed R PCB version THR, vented
Design
20 Double relay (THT) 28 Double relay (THR)
Coil
01 Standard 02 Sensitive
Contact type
A Single contact
Contact material index
4 AgSnO2 standard 8 Wiper load
Contact arrangement index
03 form C (CO)
Product code Terminal/Encl. Design Coil Contact Cont. material Arrangement Part number
V23086-C2001-A403 PCB THT, imm., clean Double Standard Single AgSnO2
2 form C, 2 CO (standard)
0-1413009-9
V23086-R2801-A403 PCB THR, vented relay 6-1414920-1
V23086-R2802-A803 Sensitive
2 form C, 2 CO (wiper load)
8-1414964-5
This list represents the most common types and does not show all variants covered by this datasheet.
Other types on request.
