Datasheet
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
EMH11 / UMH11N / IMH11A
NPN 100mA 50V Complex Digital Transistors
(Bias Resistor Built-in Transistors)
lOutline
lFeatures
1) Built-In Biasing Resistors, R
1
= R
2
= 10kW.
2) Two DTC114E chips in one package.
3) Built-in bias resistors enable the configuration of
an inverter circuit without connecting external
input resistors (see inner circuit).
4) The bias resistors consist of thin-film resistors
with complete isolation to allow negative biasing l
Inner circuit
of the input. They also have the advantage of
completely eliminating parasitic effects.
5) Only the on/off conditions need to be set for
operation, making the circuit design easy.
6) Lead Free/RoHS Compliant.
l
Application
Inverter circuit, Interface circuit, Driver circuit
lPackaging specifications
EMT6 UMT6
SMT6
3,000 H11
UMH11N UMT6 2021 TR 180 8
SMT6 2928 T108 180 8
8,000 H118
Tape width
(mm)
Basic
ordering
unit (pcs)
Marking
Reel size
(mm)
EMH11 EMT6 1616 T2R 180
3,000 H11
IMH11A
Part No. Package
Package
size
(mm)
Taping
code
Parameter Tr1 and Tr2
VCC 50V
I
C(MAX.) 100mA
R
110kW
R
210kW
EMH11
(SC-107C)
IMH11A
SOT-457 (SC-74)
UMH11N
SOT-363 (SC-88)
OUT
(6)
(2)
IN
(1)
GND
(3)
OUT
IN
(5)
GND
(4) OUT
(4)
(2)
IN
(3)
GND
(1)
OUT
IN
(5)
GND
(6)
EMH11 / UMH11N IMH11A
(6)
(5)
(4)
(1)
(2)
(3)
(4)
(5)
(6)
(3)
(2)
(1)
(6)
(5)
(4)
(1)
(2)
(3)
1/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
EMH11FHA
EMH11FHA / UMH11NFHA
UMH11NFHA
EMH11FHA
UMH11NFHA
IMH11AFRA
IMH11AFRA
IMH11AFRA
AEC-Q101 Qualified
Not Recommended for
New Designs
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Data Sheet
EMH11 / UMH11N / IMH11A
l
Absolute maximum ratings (Ta = 25°C)
<For Tr1 and Tr2 in common>
Supply voltage
Input voltage
Output current
Collector current
Power dissipation
Junction temperature
Range of storage temperature
l
Electrical characteristics
(Ta = 25°C)
<For Tr1 and Tr2 in common>
*1 Characteristics of built-in transistor
*2 Each terminal mounted on a reference footprint
*3 120mW per element must not be exceeded.
*4 200mW per element must not be exceeded.
MHzTransition frequency fT *1 VCE = 10V, IE = -5mA,
f = 100MHz -250 -
kW
Resistance ratio R2/R1-0.8 1 1.2 -
Input resistance R1-710 13
mA
DC current gain GIVO = 5V, IO = 5mA 30 ---
Output current IO(off) VCC = 50V, VI = 0V - - 0.5
V
Input current IIVI = 5V - - 0.88 mA
Output voltage VO(on) IO / II = 10mA / 0.5mA - 0.1 0.3
V
VI(on) VO = 0.3V, IO = 10mA 3.0 - -
0.5
Input voltage
VI(off) VCC = 5V, IO = 100mA- -
Parameter Symbol Conditions UnitMin. Typ. Max.
Tj150 °C
Tstg -55 to +150 °C
IC(MAX.)
*1 100 mA
EMH11 / UMH11N
PD
*2 150 (Total)*3 mW
IMH11A 300 (Total)*4 mW
VIN -10 to +40 V
IO50 mA
Parameter Symbol Values Unit
VCC 50 V
2/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
EMH11FHA / UMH11NFHA
IMH11AFRA
Not Recommended for
New Designs
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Data Sheet
EMH11 / UMH11N / IMH11A
l
Electrical characteristic curves
(Ta = 25°C)
Fig.1 Input voltage vs. output current
(ON characteristics)
INPUT VOLTAGE : VI(on) [V]
OUTPUT CURRENT : IO [A]
Fig.2 Output current vs. input voltage
(OFF characteristics)
OUTPUT CURRENT : IO [A]
INPUT VOLTAGE : VI(off)[V]
Fig.3 Output current vs. output voltage
OUTPUT CURRENT : IO [mA]
OUTPUT VOLTAGE : VO [V]
Fig.4 DC current gain vs. output current
DC CURRENT GAIN : GI
OUTPUT CURRENT : IO [A]
0
10
20
30
40
50
0 5 10
0A
140μA
160μA
200μA
220μA
240μA
260μA
180μA
I
I
=
Ta=25ºC
120μA
100μA
3/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
Not Recommended for
New Designs
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Data Sheet
EMH11 / UMH11N / IMH11A
l
Electrical characteristic curves
(Ta = 25°C)
Fig.5 Output voltage vs. output current
OUTPUT VOLTAGE : VO(on) [V]
OUTPUT CURRENT : IO [A]
4/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
Not Recommended for
New Designs
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Data Sheet
EMH11 / UMH11N / IMH11A
l
Dimensions
(Unit : mm)
Dimension in mm/inches
EMT6
Patterm of terminal position areas
㼎
㻰
㼑
㻸㼜
㻸㼜
㻱
㻴
㻱
㻸㻸
㼤㻿㻭
㻭
㼏
㻭㻝
㻭
㼥㻿
㻿
㼑㻝
㼎㻞
㼘㻝
㼑
㻹㻵㻺 㻹㻭㼄 㻹㻵㻺 㻹㻭㼄
㻭㻝 㻜㻚㻜㻜 㻜㻚㻝㻜 㻜㻜㻚㻜㻜㻠
㻭 㻜㻚㻠㻡 㻜㻚㻡㻡 㻜㻚㻜㻝㻤 㻜㻚㻜㻞㻞
㼎 㻜㻚㻝㻣 㻜㻚㻞㻣 㻜㻚㻜㻜㻣 㻜㻚㻜㻝㻝
㼏 㻜㻚㻜㻤 㻜㻚㻝㻤 㻜㻚㻜㻜㻟 㻜㻚㻜㻜㻣
㻰 㻝㻚㻡㻜 㻝㻚㻣㻜 㻜㻚㻜㻡㻥 㻜㻚㻜㻢㻣
㻱 㻝㻚㻝㻜 㻝㻚㻟㻜 㻜㻚㻜㻠㻟 㻜㻚㻜㻡㻝
㼑
㻴㻱㻝㻚㻡㻜 㻝㻚㻣㻜 㻜㻚㻜㻡㻥 㻜㻚㻜㻢㻣
㻸 㻜㻚㻝㻜 㻜㻚㻟㻜 㻜㻚㻜㻜㻠 㻜㻚㻜㻝㻞
㻸㼜 㻙㻜㻚㻟㻡 㻙㻜㻚㻜㻝㻠
㼤 㻙 㻜㻚㻝㻜 㻙㻜㻚㻜㻜㻠
㼥 㻙 㻜㻚㻝㻜 㻙㻜㻚㻜㻜㻠
㻹㻵㻺 㻹㻭㼄 㻹㻵㻺 㻹㻭㼄
㼑㻝
㼎㻞 㻙㻜㻚㻟㻣 㻙㻜㻚㻜㻝㻡
㼘㻝 㻙㻜㻚㻠㻡 㻙㻜㻚㻜㻝㻤
㻵㻺㻯㻴㻱㻿
㻜㻚㻡㻜
㻜㻚㻜㻞
㻰㻵㻹
㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿
㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿
㻵㻺㻯㻴㻱㻿
㻝㻚㻞㻡
㻜㻚㻜㻠㻥
㻰㻵㻹
5/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
Not Recommended for
New Designs
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Data Sheet
EMH11 / UMH11N / IMH11A
l
Dimensions
(Unit : mm)
Dimension in mm/inches
UMT6
Patterm of terminal position areas
㻱
㼤 㻿 㻭
㻭
㻱
㻴
㼑
㻰
㼎
㼏
㻽
㻭㻟
㻸㻝
㻸㼜
㼥㻿
㻭㻝
㼑㻝
㼎㻞
㼘㻝
㼑
㻭
㻿
㻹㻵㻺 㻹㻭㼄 㻹㻵㻺 㻹㻭㼄
㻭 㻜㻚㻤㻜 㻝㻚㻜㻜 㻙㻜㻚㻜㻟㻥
㻭㻝 㻜㻚㻜㻜 㻜㻚㻝㻜 㻜㻜㻚㻜㻜㻠
㻭㻟
㼎 㻜㻚㻝㻡 㻜㻚㻟㻜 㻜㻚㻜㻜㻢 㻜㻚㻜㻝㻞
㼏 㻜㻚㻝㻜 㻜㻚㻞㻜 㻜㻚㻜㻜㻠 㻜㻚㻜㻜㻤
㻰 㻝㻚㻥㻜 㻞㻚㻝㻜 㻜㻚㻜㻣㻡 㻜㻚㻜㻤㻟
㻱 㻝㻚㻝㻡 㻝㻚㻟㻡 㻜㻚㻜㻠㻡 㻜㻚㻜㻡㻟
㼑
㻴
㻱
㻞㻚㻜㻜 㻞㻚㻞㻜 㻜㻚㻜㻣㻥 㻜㻚㻜㻤㻣
㻸㻝 㻜㻚㻞㻜 㻜㻚㻡㻜 㻜㻚㻜㻜㻤 㻜㻚㻜㻞
㻸㼜 㻜㻚㻞㻡 㻜㻚㻡㻡 㻜㻚㻜㻝 㻜㻚㻜㻞㻞
㻽 㻜㻚㻝㻜 㻜㻚㻟㻜 㻜㻚㻜㻜㻠 㻜㻚㻜㻝㻞
㼤 㻙 㻜㻚㻝㻜 㻙㻜㻚㻜㻜㻠
㼥 㻙 㻜㻚㻝㻜 㻙㻜㻚㻜㻜㻠
㻹㻵㻺 㻹㻭㼄 㻹㻵㻺 㻹㻭㼄
㼑㻝
㼎㻞 㻙㻜㻚㻠㻜 㻙㻜㻚㻜㻝㻢
㼘㻝 㻙㻜㻚㻢㻡 㻙㻜㻚㻜㻞㻢
㻜㻚㻞㻡
㻜㻚㻜㻝
㻰㻵㻹
㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿
㻵㻺㻯㻴㻱㻿
㻝㻚㻡㻡
㻜㻚㻜㻢
㻰㻵㻹
㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿
㻵㻺㻯㻴㻱㻿
㻜㻚㻢㻡
㻜㻚㻜㻟
6/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
Not Recommended for
New Designs
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Data Sheet
EMH11 / UMH11N / IMH11A
l
Dimensions
(Unit : mm)
Dimension in mm/inches
SMT6
Patterm of terminal position areas
㻱
㼑
㻰
㻱
㻴
㼎㼤 㻿 㻭
㻭
㼏
㻽
㻭㻟
㻸㻝
㻸㼜
㻭㻝
㻭
㻿
㼥㻿
㼑㻝
㼑
㼘㻝
㼎㻞
㻹㻵㻺 㻹㻭㼄 㻹㻵㻺 㻹㻭㼄
㻭 㻝㻚㻜㻜 㻝㻚㻟㻜 㻜㻚㻜㻟㻥 㻜㻚㻜㻡㻝
㻭㻝 㻜㻚㻜㻜 㻜㻚㻝㻜 㻜㻜㻚㻜㻜㻠
㻭㻟
㼎 㻜㻚㻞㻡 㻜㻚㻠㻜 㻜㻚㻜㻝 㻜㻚㻜㻝㻢
㼏 㻜㻚㻜㻥 㻜㻚㻞㻡 㻜㻚㻜㻜㻠 㻜㻚㻜㻝
㻰 㻞㻚㻤㻜 㻟㻚㻜㻜 㻜㻚㻝㻝 㻜㻚㻝㻝㻤
㻱 㻝㻚㻡㻜 㻝㻚㻤㻜 㻜㻚㻜㻡㻥 㻜㻚㻜㻣㻝
㼑
㻴
㻱
㻞㻚㻢㻜 㻟㻚㻜㻜 㻜㻚㻝㻜㻞 㻜㻚㻝㻝㻤
㻸㻝 㻜㻚㻟㻜 㻜㻚㻢㻜 㻜㻚㻜㻝㻞 㻜㻚㻜㻞㻠
㻸㼜 㻜㻚㻠㻜 㻜㻚㻣㻜 㻜㻚㻜㻝㻢 㻜㻚㻜㻞㻤
㻽 㻜㻚㻞㻜 㻜㻚㻟㻜 㻜㻚㻜㻜㻤 㻜㻚㻜㻝㻞
㼤 㻙 㻜㻚㻞㻜 㻙㻜㻚㻜㻜㻤
㼥 㻙 㻜㻚㻝㻜 㻙㻜㻚㻜㻜㻠
㻹㻵㻺 㻹㻭㼄 㻹㻵㻺 㻹㻭㼄
㼑㻝
㼎㻞 㻜㻚㻢㻜 㻙㻜㻚㻜㻞㻠
㼘㻝 㻙㻜㻚㻥㻜 㻙㻜㻚㻜㻟㻡
㻜㻚㻞㻡
㻜㻚㻜㻝
㻰㻵㻹
㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿
㻵㻺㻯㻴㻱㻿
㻞㻚㻝㻜
㻜㻚㻜㻤
㻰㻵㻹
㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿
㻵㻺㻯㻴㻱㻿
㻜㻚㻥㻡
㻜㻚㻜㻠
7/7 2012.06 - Rev.B
EMH11FHA / UMH11NFHA / IMH11AFRA
Not Recommended for
New Designs
Datasheet
Datasheet
Notice-PAA-E Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred b y you or third parties arising from the use of an y
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN USA EU CHINA
CLASSⅢ CLASSⅢ CLASSⅡb CLASSⅢ
CLASSⅣ CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe d esign against the physical injur y, damage to any property, which
a failure or malfunction of our Products may cause. T he following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expens es or losses arising from the
use of any ROHM’s Products under an y special or extraordinary envir onments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product perfor mance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlig ht or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing comp onents, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flu x (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Po wer Dissipation (P d) depe nding on Ambient temperature (T a). When us ed in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way r esponsible or liable for failure induced under dev iant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlori ne, bromine, etc.) flu x is used, the residue of flux may negativel y affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM represe ntative in advance.
For details, please refer to ROHM Mounting specification
Not Recommended for
New Designs
Datasheet
Datasheet
Notice-PAA-E Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise you r own indepen dent verificati on and judgme nt in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please t ake special care under dry condit ion (e.g. Grounding of human body / equipment / sol der iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportati on
1. Product performance and soldered connections ma y deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, sold erability of products out of recommende d storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommen de d storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive s t ress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Pr oducts of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products pl ease dispose them properly using an auth orized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoi ng information or data will not infringe any int ellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained i n this document. Provide d, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without pri or written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including b ut not limi ted to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Not Recommended for
New Designs
DatasheetDatasheet
Notice – WE Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or
concerning such information.
Not Recommended for
New Designs
