DETAIL SPECIFIC ATION SHEET
CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING),
PLUG, (BAYONET COUPLING, CRIM P PIN CONTACT),
(SERIES III, CLASSES A, G, M, R, T, W AND Z)
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-83723.
FIGURE 1. Dimensions and configurations.
AMSC N/A FSC 5935
INCH-POUND
MIL-DTL-83723/76E
19 August 2009
SUPERSEDING
MIL-DTL-83723/76D
15 September 2006
MIL-DTL-83723/76E
2
Shell
size
A
max G
min H J L
min
U
max V
8
.312
.352 .415
.424
.540
.545
.632 .776 .025
10
.388 .428 .517
.526
.662
.667
.760 .906 .031
12
.558 .598 .687
.696
.832
.837
.930 1.078 .031
14
.627 .667 .756
.765
.901
.906
.999 1.141 .031
16
.772 .794 .883
.892
1.028
1.033
1.126 1.266 .031
18
.860 .900 .989
.998
1.134
1.139
1.232 1.375 .031
20
.985 1.025 1.114
1.123
1.261
1.266
1.357 1.510 .031
22
1.110 1.150 1.239
1.248
1.384
1.389
1.482 1.625 .031
24
1.235 1.275 1.364
1.373
1.511
1.516
1.607 1.760 .031
FIGURE 1. Dimensions and configurations - Continued.
MIL-DTL-83723/76E
3
Inches mm Inches mm Inches mm Inches mm Inches mm
.008 0.20 .177 4.50 .545 13.84 .900 22.86 1.235 31.37
.015 0.38 .182 4.62 .552 14.02 .901 22.89 1.239 31.47
.018 0.46 .185 4.70 .558 14.17 .906 23.01 1.248 31.70
.020 0.51 .198 5.03 .598 15.19 .930 23.62 1.261 32.03
.022 0.56 .200 5.08 .627 15.93 .985 25.02 1.266 32.16
.025 0.64 .204 5.18 .632 16.05 .989 25.12 1.275 32.39
.031 0.79 .211 5.36 .662 16.81 .998 25.35 1.357 34.47
.032 0.81 .259 6.58 .667 16.94 .999 25.37 1.364 34.65
.042 1.07 .312 7.92 .678 17.22 1.025 26.04 1.373 34.87
.046 1.17 .316 8.03 .687 17.45 1.028 19.84 1.375 34.93
.065 1.65 .320 8.13 .696 17.68 1.033 26.24 1.384 35.15
.069 1.75 .330 8.38 .756 19.20 1.110 27.38 1.389 35.28
.084 2.13 .352 8.94 .760 19.30 1.078 28.19 1.482 37.64
.090 2.29 .366 9.30 .765 19.43 1.114 28.30 1.510 38.35
.097 2.46 .383 9.73 .772 19.61 1.123 28.52 1.511 38.38
.101 2.57 .388 9.86 .776 19.71 1.126 28.60 1.516 38.51
.106 2.69 .415 10.54 .794 20.17 1.134 28.80 1.607 40.82
.112 2.84 .424 10.77 .832 21.13 1.139 28.93 1.625 41.28
.125 3.18 .428 10.87 .837 21.26 1.411 28.98 1.760 44.70
.138 3.51 .517 13.13 .860 21.84 1.150 29.21
.144 3.66 .526 13.36 .883 22.43 1.230 31.24
.170 4.32 .540 13.72 .892 22.66 1.232 31.29
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13 mm) for three place decimals and
± .01 (0.25 mm) for two place decimals and ± 1o for all angles.
4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723.
5. See table I for contact cavities requiring this dimension.
FIGURE 1. Dimensions and configurations - Continued.
MIL-DTL-83723/76E
4
REQUIREMENTS:
Dimensions and configurations: See figure 1.
For insert arrangements, see MIL-STD-1554 and table I.
TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities.
Shell
size
Insert
arrangements
8
03
10
06
For connector accessories: See SAE-AS85049.
This connector mates with MIL-DTL-83723/71 and /73.
Part or Identifying Number (PIN) example:
M83723/ 76 W 22 55 N
Military designator
Specification sheet number
Class
Shell size
Insert arrangement
Polarizing position
Changes from previous issue. Marginal notations are not used in this revision to identify changes with
respect to the previous issue due to the extent of the changes.
Referenced documents. In addition to MIL-DTL-83723, this document references the following:
MIL-DTL-83723/71
MIL-DTL-83723/73
MIL-STD-1554
SAE-AS85049
MIL-DTL-83723/76E
5
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army - CR DLA - CC
Navy - AS
Air Force - 85
DLA - CC
Review activities: (Project 5935-2008-158)
Army - AR, MI
Navy - EC
Air Force – 19
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above
using the ASSIST Online database at http://assist.daps.dla.mil.