TSOP311.., TSOP313.., TSOP315.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Very low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Improved shielding against EMI * Supply voltage: 2.5 V to 5.5 V * Improved immunity against ambient light * Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC * Insensitive to supply voltage ripple and noise 1 2 94 8691 3 DESCRIPTION The TSOP311.., TSOP313.. and TSOP315.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP311.. is compatible with all common IR remote control data formats. The TSOP313.. is optimized to better suppress spurious pulses from energy saving fluorescent lamps. The TSOP315.. has an excellent noise suppression. It is immune to dimmed LCD backlighting and any fluorescent lamps. AGC3 and AGC5 may also suppress some data signals in case of continuous transmission. This component has not been qualified according to automotive specifications. MECHANICAL DATA Pinning: 1 = GND, 2 = VS, 3 = OUT PARTS TABLE SHORT BURSTS AND HIGH DATA RATES (AGC1) NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) VERY NOISY ENVIRONMENTS AND SHORT BURSTS (AGC5) 30 kHz TSOP31130 TSOP31330 TSOP31530 33 kHz TSOP31133 TSOP31333 TSOP31533 36 kHz TSOP31136 TSOP31336 TSOP31536 38 kHz TSOP31138 TSOP31338 TSOP31538 40 kHz TSOP31140 TSOP31340 TSOP31540 56 kHz TSOP31156 TSOP31356 TSOP31556 CARRIER FREQUENCY BLOCK DIAGRAM APPLICATION CIRCUIT 17170_5 2 30 k VS Transmitter with TSALxxxx 3 Input AGC Band pass Demodulator OUT 1 PIN Control circuit GND R1 IR receiver VS Circuit 16832 + VS C1 C OUT GND VO GND R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 < R1 < 1 k, C1 > 0.1 F. ** Please see document "Vishay Material Category Policy": www.vishay.com/doc?99902 www.vishay.com 1 Document Number: 81763 Rev. 1.6, 04-Feb-11 TSOP311.., TSOP313.., TSOP315.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage (pin 2) TEST CONDITION VS - 0.3 to + 6 V Supply current (pin 2) IS 3 mA Output voltage (pin 3) VO - 0.3 to (VS + 0.3) V Output current (pin 3) IO 5 mA Junction temperature Storage temperature range Operating temperature range Tj 100 C Tstg - 25 to + 85 C Tamb - 25 to + 85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Power consumption Soldering temperature UNIT Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER Supply current (pin 2) TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 3.3 V ISD 0.27 0.35 0.45 Ev = 40 klx, sunlight ISH Supply voltage VS 2.5 d IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max. Directivity Angle of half transmission distance 1/2 Output voltage low (pin 3) mA 0.45 Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 250 mA Transmission distance UNIT mA 5.5 V 45 m 0.15 100 mV 0.35 mW/m2 W/m2 30 45 deg TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 0.4 Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) t tpi *) T *) tpi 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 tpo - Output Pulse Width (ms) Ee 0.35 0.3 0.25 Output Pulse Width 0.2 0.15 Input Burst Length 0.1 = 950 nm, optical test signal, fig. 1 0.05 0 VOL td 1) tpo 2) Fig. 1 - Output Active Low Document Number: 81763 Rev. 1.6, 04-Feb-11 0.1 t 20771 1 10 100 1000 10 000 100 000 Ee - Irradiance (mW/m) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient www.vishay.com 2 TSOP311.., TSOP313.., TSOP315.. Optical Test Signal Ee 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL t off t on t Ee min. - Threshold Irradiance (mW/m2) IR Receiver Modules for Remote Control Systems Vishay Semiconductors 4 Correlation with Ambient Light Sources: 2 3.5 10 W/m = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m2 = 8.2 kLx (Daylight, T = 5900 K) 3 Wavelength of Ambient Illumination: = 950 nm 2.5 2 1.5 1 0.5 0 0.01 Fig. 3 - Output Function Ee min. - Threshold Irradiance (mW/m2) Ton, Toff - Output Pulse Width (ms) Ton 0.6 0.5 Toff 0.4 0.3 0.2 0.1 = 950 nm, Optical Test Signal, Fig. 3 0 0.1 1 10 100 1000 100 f = 100 Hz 0.9 0.8 f = 10 kHz 0.7 0.6 f = 20 kHz 0.5 0.4 f = 30 kHz 0.3 f = fo 0.2 0.1 0 1 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) 20753 Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 E - Max. Field Strength (V/m) 500 1.0 E e min./Ee - Rel. Responsivity 10 1.0 10 000 Ee - Irradiance (mW/m2) 20759 1 Fig. 6 - Sensitivity in Bright Ambient 0.8 0.7 0.1 Ee - Ambient DC Irradiance (W/m2) 20757 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 450 400 350 300 250 200 150 100 50 0.0 0 0.7 16925 0.9 1.1 1.3 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity www.vishay.com 3 0 20747 500 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances Document Number: 81763 Rev. 1.6, 04-Feb-11 TSOP311.., TSOP313.., TSOP315.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors 0 1 10 20 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 1.0 0.6 TSOP311.. 0.5 0.9 50 0.8 60 0.4 f = 38 kHz, Ee = 2 mW/m 0.3 70 TSOP313.. 0.2 0.7 80 0.1 TSOP315.. 0 0 22180-2 20 40 60 80 100 0.6 120 19258 Burst Length (number of cycles/burst) Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length Ee min. - Threshold Irradiance (mW/m2) 0.4 0 Fig. 12 - Horizontal Directivity 0 0.3 10 20 30 0.25 40 0.2 1.0 0.15 0.9 50 0.1 0.8 60 0.05 0.7 70 80 0 - 30 - 10 10 30 50 70 90 Tamb - Ambient Temperature (C) 20755 0.6 0.4 0.2 0 d rel - Relative Transmission Distance 19259 Fig. 10 - Sensitivity vs. Ambient Temperature Fig. 13 - Vertical Directivity 1.2 0.2 Ee min. - Sensitivity (mW/m2) S ()rel - Relative Spectral Sensitivity 0.2 drel - Relative Transmission Distance 1.0 0.8 0.6 0.4 0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 750 94 8408 0 850 950 1050 - Wavelength (nm) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength Document Number: 81763 Rev. 1.6, 04-Feb-11 2 1150 20756 2.5 3 3.5 4 4.5 5 5.5 6 VS - Supply Voltage (V) Fig. 14 - Sensitivity vs. Supply Voltage www.vishay.com 4 TSOP311.., TSOP313.., TSOP315.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems The TSOP311.., TSOP313.. and TSOP315.. series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP311.., TSOP313.. and TSOP315.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: IR Signal SUITABLE DATA FORMAT * DC light (e.g. from tungsten bulb or sunlight) 0 * Continuous signals at any frequency 5 * Modulated noise from fluorescent lamps with electronic ballasts 10 15 20 Time (ms) 16920 IR Signal Fig. 15 - IR Signal from Fluorescent Lamp with Low Modulation 0 5 10 15 20 Time (ms) 16921 Fig. 16 - IR Signal from Fluorescent Lamp with High Modulation TSOP311.. TSOP313.. TSOP315.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 70 cycles 10 cycles 6 to 35 cycles 10 cycles 6 to 24 cycles 10 cycles 70 cycles 35 cycles 24 cycles > 1.2 x burst length > 6 x burst length > 25 ms 2000 2000 2000 For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second Recommended for NEC code yes yes yes Recommended for RC5/RC6 code yes yes yes Recommended for Sony code yes no no Recommended for RCMM code yes yes yes Recommended for r-step code yes yes yes Recommended for XMP code yes yes yes Suppression of interference from fluorescent lamps Common disturbance signals are Even critical disturbance signals Even critical disturbance signals supressed (example: are suppressed (examples: signal are suppressed (examples: signal signal pattern of fig. 15) pattern of fig. 15 and fig. 16) pattern of fig. 15 and fig. 16) Note * For data formats with short bursts please see the datasheet for TSOP312.., TSOP314.. www.vishay.com 5 Document Number: 81763 Rev. 1.6, 04-Feb-11 TSOP311.., TSOP313.., TSOP315.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 10 0.3 (9.2) 0.65 + 0.10 - 0.15 0.8 max. 30.6 0.5 12.5 0.4 Center of sensitive area 0.5 Area not plane 0.4 + 0.15 - 0.05 2.54 nom. + 0.10 - 0.05 1.4 0.3 3 x 2.54 = 7.62 nom. 4 0.3 5.8 0.3 R 2.75 technical drawings according to DIN specifications Drawing-No.: 6.550-5095.01-4 Issue: 20; 15.03.10 96 12116 Document Number: 81763 Rev. 1.6, 04-Feb-11 www.vishay.com 6 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000