W83627EHG - NUVOTON - Datasheet.Live

W83627EHF/EF

W83627EHG/EG

NUVOTON LPC I/O

Note: This document is both for UBC and UBH version

except the specified descriptions

Date: April 7th, 2009 Revision: 1.94

Publication Release Date: April 7 , 2009

-I- Version 1.94

W83627EHF/EF

W83627EHG/EG

TABLE OF CONTENTS-

1. GENERAL DESCRIPTION ......................................................................................................... 1

2. FEATURES ................................................................................................................................. 3

3. BLOCK DIAGRAM ...................................................................................................................... 7

4. PIN CONFIGURATION ...............................................................................................................9

5. PIN DESCRIPTION................................................................................................................... 11

5.1 LPC Interface ...................................................................................................................... 11

5.2 FDC Interface...................................................................................................................... 12

5.3 Multi-Mode Parallel Port...................................................................................................... 14

5.4 Serial Port & Infrared Port Interface.................................................................................... 16

5.5 KBC Interface...................................................................................................................... 19

5.6 Hardware Monitor Interface ................................................................................................ 19

5.7 Game Port & MIDI Port ....................................................................................................... 21

5.8 ACPI Interface..................................................................................................................... 23

5.9 General Purpose I/O Port ................................................................................................... 24

5.9.1 GPIO Power Source.........................................................................................................24

5.9.2 GPIO-1 Interface..............................................................................................................24

5.9.3 GPIO-2 Interface..............................................................................................................24

5.9.4 GPIO-3 Interface..............................................................................................................25

5.9.5 GPIO-4 Interface..............................................................................................................26

5.9.6 GPIO-5 Interface..............................................................................................................26

5.9.7 GPIO-6 Interface..............................................................................................................27

5.9.8 GPIO-1 and GPIO-4 with WDTO# / SUSLED / PLED multi-function................................27

5.10 POWER PINS ..................................................................................................................... 27

6. CONFIGURATION REGISTER ACCESS PROTOCOL ........................................................... 29

6.1 Configuration Sequence ..................................................................................................... 30

6.1.1 Enter the Extended Function Mode..................................................................................31

6.1.2 Configure the Configuration Registers .............................................................................31

6.1.3 Exit the Extended Function Mode ....................................................................................31

- II -

W83627EHF/EF

W83627EHG/EG

6.1.4 Software Programming Example......................................................................................31

7. HARDWARE MONITOR ........................................................................................................... 33

7.1 General Description ............................................................................................................ 33

7.2 Access Interface ................................................................................................................. 34

7.2.1 LPC interface ...................................................................................................................34

7.2.2 I2C interface .....................................................................................................................35

7.2.2.1. Serial bus (I2C) access timing ............................................................................................................ 36

7.3 Analog Inputs ...................................................................................................................... 36

7.3.1 Monitor over 2.048V voltage ............................................................................................37

7.3.2 CPUVCORE voltage detection method............................................................................38

7.3.3 Temperature Measurement Machine ...............................................................................38

7.3.3.1. Monitor temperature from thermistor.................................................................................................. 39

7.3.3.2. Monitor temperature from Pentium IITM/Pentium IIITM thermal diode .................................................. 39

7.4 FAN Speed Count and FAN Speed Control ....................................................................... 40

7.4.1 Fan speed count ..............................................................................................................40

7.4.2 Fan speed control ............................................................................................................41

7.4.2.1. PWM Duty Cycle Output .................................................................................................................... 41

7.4.2.2. DC Voltage Output ............................................................................................................................. 41

7.5 Conversion Sequence and Conversion Time ..................................................................... 41

7.6 Smart Fan Control...............................................................................................................43

7.6.1 Thermal Cruise mode.......................................................................................................43

7.6.2 Fan Speed Cruise mode ..................................................................................................45

7.6.3 Manual Control Mode.......................................................................................................46

7.6.4 Smart FanTM III Mode.......................................................................................................51

7.7 SMI# interrupt mode ........................................................................................................... 54

7.7.1 Voltage SMI# mode..........................................................................................................54

7.7.2 Fan SMI# mode................................................................................................................54

7.7.3 Temperature SMI# mode .................................................................................................55

7.7.3.1. Temperature sensor 1(SYSTIN) SMI# interrupt has 3 modes ........................................................... 55

7.7.3.2. Temperature sensor 2(CPUTIN) and sensor 3(AUXTIN) SMI# interrupt has two modes .................. 57

Publication Release Date: April 7 , 2009

-III- Versio n 1. 94

W83627EHF/EF

W83627EHG/EG

7.8 OVT# interrupt mode .......................................................................................................... 58

7.9 Registers and RAM............................................................................................................. 59

7.9.1 Address Port (Port x5h)....................................................................................................59

7.9.2 Data Port (Port x6h) .........................................................................................................59

7.9.3 SYSFANOUT PWM Output Frequency Configuration Register - Index 00h (Bank 0) ......60

7.9.4 SYSFANOUT Output Value Select Register - Index 01h (Bank 0)...................................61

7.9.5 CPUFANOUT0 PWM Output Frequency Configuration Register - Index 02h (Bank 0)....63

7.9.6 CPUFANOUT0 Output Value Select Register - Index 03h (Bank 0) ................................64

7.9.7 FAN Configuration Register I - Index 04h (Bank 0) ..........................................................64

7.9.8 SYSTIN Target Temperature Register/ SYSFANIN Target Speed Register - Index 05h

(Bank 0) 65

7.9.9 CPUTIN Target Temperature Register/ CPUFANIN0 Target Speed Register - Index 06h

(Bank 0) 66

7.9.10 Tolerance of Target Temperature or Target Speed Register - Index 07h (Bank 0)..........66

7.9.11 SYSFANOUT Stop Value Register - Index 08h (Bank 0) .................................................67

7.9.12 CPUFANOUT0 Stop Value Register - Index 09h (Bank 0)...............................................68

7.9.13 SYSFANOUT Start-up Value Register - Index 0Ah (Bank 0) ...........................................68

7.9.14 CPUFANOUT0 Start-up Value Register - Index 0Bh (Bank 0).........................................69

7.9.15 SYSFANOUT Stop Time Register - Index 0Ch (Bank 0)..................................................69

7.9.16 CPUFANOUT0 Stop Time Register - Index 0Dh (Bank 0) ...............................................70

7.9.17 Fan Output Step Down Time Register - Index 0Eh (Bank 0)............................................71

7.9.18 Fan Output Step Up Time Register - Index 0Fh (Bank 0) ................................................71

7.9.19 AUXFANOUT PWM Output Frequency Configuration Register - Index 10h (Bank 0)......72

7.9.20 AUXFANOUT Output Value Select Register - Index 11h (Bank 0) ..................................73

7.9.21 FAN Configuration Register II - Index 12h (Bank 0) .........................................................73

7.9.22 AUXTIN Target Temperature Register/ AUXFANIN0 Target Speed Register - Index 13h

(Bank 0) 74

7.9.23 Tolerance of Target Temperature or Target Speed Register - Index 14h (Bank 0)..........75

7.9.24 AUXFANOUT Stop Value Register - Index 15h (Bank 0).................................................76

- IV -

W83627EHF/EF

W83627EHG/EG

7.9.25 AUXFANOUT Start-up Value Register - Index 16h (Bank 0) ...........................................76

7.9.26 AUXFANOUT Stop Time Register - Index 17h (Bank 0) ..................................................77

7.9.27 OVT# Configuration Register - Index 18h (Bank 0)..........................................................77

7.9.28 Reserved - Index 19h-1Fh (Bank 0) .................................................................................78

7.9.29 Value RAM ⎯ Index 20h- 3Fh (Bank 0) ........................................................................78

7.9.30 Configuration Register - Index 40h (Bank 0) .................................................................80

7.9.31 Interrupt Status Register 1 - Index 41h (Bank 0) ...........................................................81

7.9.32 Interrupt Status Register 2 - Index 42h (Bank 0) ...........................................................82

7.9.33 SMI# Mask Register 1 - Index 43h (Bank 0)..................................................................82

7.9.34 SMI# Mask Register 2 - Index 44h (Bank 0)..................................................................83

7.9.35 Reserved Register - Index 45h (Bank 0)......................................................................83

7.9.36 SMI# Mask Register 3 - Index 46h (Bank 0)..................................................................83

7.9.37 Fan Divisor Register I - Index 47h (Bank 0)...................................................................84

7.9.38 Serial Bus Address Register - Index 48h (B ank 0) ........................................................85

7.9.39 Reserved - Index 49h (Bank 0)......................................................................................85

7.9.40 CPUFANOUT1 with Temperature source Select - Index 4Ah (Bank 0) .........................85

7.9.41 Fan Divisor Register II - Index 4Bh (Bank 0) .................................................................86

7.9.42 SMI#/OVT# Control Register - Index 4Ch (Bank 0) .......................................................86

7.9.43 FAN IN/OUT Control Register - Index 4Dh (Bank 0) .....................................................87

7.9.44 Register 50h ~ 5Fh Bank Select Register - Index 4Eh (Bank 0)....................................88

7.9.45 Nuvoton Vendor ID Register - Index 4Fh (B ank 0) ........................................................89

7.9.46 Nuvoton Test Register - Index 50h-55h (Bank 0) .............................................................90

7.9.47 BEEP Control Register 1 - Index 56h (Bank 0) ................................................................90

7.9.48 BEEP Control Register 2 - Index 57h (Bank 0) ................................................................91

7.9.49 Chip ID - Index 58h (Bank 0)............................................................................................92

7.9.50 Diode Selection Register - Index 59h (Bank 0) ................................................................92

7.9.51 Reserved - Index 5Ah-5Ch (Bank 0) ................................................................................93

7.9.52 VBAT Monitor Control Register - Index 5Dh (Bank 0) ......................................................93

7.9.53 Reserved Register - Index 5Eh-5Fh (Bank 0) ..................................................................94

7.9.54 CPUFANOUT1 PWM Output Frequency Configuration Register - Index 60h (Bank 0)....94

Publication Release Date: April 7 , 2009

-V- Version 1.94

W83627EHF/EF

W83627EHG/EG

7.9.55 CPUFANOUT1 Output Value Select Register - Index 61h (Bank 0) ................................95

7.9.56 FAN Configuration Register III - Index 62h (Bank 0) ........................................................95

7.9.57 Target Temperature Register/ CPUFANIN1 Target Speed Register - Index 63h (Bank 0)

7.9.58 CPUFANOUT1 Stop Value Register - Index 64h (Bank 0)...............................................97

7.9.59 CPUFANOUT1 Start-up Value Register - Index 65h (Bank 0) .........................................97

7.9.60 CPUFANOUT1 Stop Time Register - Index 66h (Bank 0)................................................98

7.9.61 CPUFANOUT0 Maximum Output Value Register - Index 67h (Bank 0)...........................99

7.9.62 CPUFANOUT0 Output Step Value Register - Index 68h (Bank 0)...................................99

7.9.63 CPUFANOUT1 Maximum Output Value Register - Index 69h (Bank 0)...........................99

7.9.64 CPUFANOUT1 Output Step Value Register - Index 6Ah (Bank 0) ................................100

7.9.65 CPUTIN Temperature Sensor Temperature (High Byte) Register - Index 50h (Bank 1) 100

7.9.66 CPUTIN Temperature Sensor Temperature (Low Byte) Register - Index 51h (Bank 1).101

7.9.67 CPUTIN Temperature Sensor Configuration Register - Index 52h (Bank 1) ..................101

7.9.68 CPUTIN Temperature Sensor Hysteresis (High Byte) Register - Index 53h (Bank 1)....102

7.9.69 CPUTIN Temperature Sensor Hysteresis (Low Byte) Register - Index 54h (Bank 1).....102

7.9.70 CPUTIN Temperature Sensor Over-temperature (High Byte) Register - Index 55h (Bank1)

103

7.9.71 CPUTIN Temperature Sensor Over-temperature (Low Byte) Register - Index 56h (Bank 1)

103

7.9.72 AUXTIN Temperature Sensor Temperature (High Byte) Register - Index 50h (Bank 2) 103

7.9.73 AUXTIN Temperature Sensor Temperature (Low Byte) Register - Index 51h (Bank 2) .104

7.9.74 AUXTIN Temperature Sensor Configuration Register - Index 52h (Bank 2) ..................104

7.9.75 AUXTIN Temperature Sensor Hysteresis (High Byte) Register - Index 53h (Bank 2) ....105

7.9.76 AUXTIN Temperature Sensor Hysteresis (Low Byte) Register - Index 54h (Bank 2).....105

7.9.77 AUXTIN Temperature Sensor Over-temperature (High Byte) Register - Index 55h (Bank 2)

106

7.9.78 AUXTIN Temperature Sensor Over-temperature(Low Byte) Register - Index 56h (Bank 2)

106

- VI -

W83627EHF/EF

W83627EHG/EG

7.9.79 Interrupt Status Register 3 - Index 50h (Bank 4) ............................................................107

7.9.80 SMI# Mask Register 4 - Index 51h (Bank 4) ..................................................................107

7.9.81 Reserved Register - Index 52h (Bank 4) ........................................................................108

7.9.82 BEEP Control Register 3 - Index 53h (Bank 4) ..............................................................108

7.9.83 SYSTIN Temperature Sensor Offset Register - Index 54h (Bank 4) ..............................109

7.9.84 CPUTIN Temperature Sensor Offset Register - Index 55h (Bank 4)..............................109

7.9.85 AUXTIN Temperature Sensor Offset Register - Index 56h (Bank 4) ..............................110

7.9.86 Reserved Register - Index 57h-58h (Bank 4).................................................................110

7.9.87 Real Time Hardware Status Register I - Index 59h (Bank 4) .........................................110

7.9.88 Real Time Hardware Status Register II - Index 5Ah (Bank 4) ........................................111

7.9.89 Real Time Hardware Status Register III - Index 5Bh (Bank 4) .......................................112

7.9.90 Reserved Register - Index 5Ch-5Dh (Bank 4)................................................................113

7.9.91 Value RAM 2 ⎯ Index 50h-59h (Bank 5) ....................................................................113

7.9.92 Nuvoton Test Register - Index 50h-57h (Bank 6)...........................................................114

8. FLOPPY DISK CONTROLLER............................................................................................... 115

8.1 FDC Functional Description .............................................................................................. 115

8.1.1 FIFO (Data)....................................................................................................................115

8.1.2 Data Separator...............................................................................................................116

8.1.3 Write Precompensation..................................................................................................116

8.1.4 Perpendicular Recording Mode......................................................................................116

8.1.5 FDC Commands ............................................................................................................117

8.2 Register Descriptions........................................................................................................ 131

8.2.1 Status Register A (SA Register) (Read base address + 0) ............................................131

8.2.2 Status Register B (SB Register) (Read base address + 1) ............................................133

8.2.3 Digital Output Register (DO Register) (Write base address + 2)....................................135

8.2.4 Tape Drive Register (TD Register) (Read base address + 3) ........................................136

8.2.5 Main Status Register (MS Register) (Read base address + 4) ......................................137

8.2.6 Data Rate Register (DR Register) (Write base address + 4)..........................................137

8.2.7 FIFO Register (R/W base address + 5)..........................................................................139

8.2.8 Digital Input Register (DI Register) (Read base address + 7) ........................................141

Publication Release Date: April 7 , 2009

-VII- Version 1.94

W83627EHF/EF

W83627EHG/EG

8.2.9 Configuration Control Register (CC Register) (Write base address + 7) ........................142

9. UART PORT ........................................................................................................................... 144

9.1 Universal Asynchronous Receiver/Transmitter (UART A, UART B)................................. 144

9.2 Register Description.......................................................................................................... 144

9.2.1 UART Control Register (UCR) (Read/Write) ..................................................................144

9.2.2 UART Status Register (USR) (Read/Write)....................................................................148

9.2.3 Handshake Control Register (HCR) (Read/Write)..........................................................149

9.2.4 Handshake Status Register (HSR) (Read/Write) ...........................................................150

9.2.5 UART FIFO Control Register (UFR) (Write only) ...........................................................151

9.2.6 Interrupt Status Register (ISR) (Read only) ...................................................................151

9.2.7 Interrupt Control Register (ICR) (Read/Write) ................................................................153

9.2.8 Programmable Baud Generator (BLL/BHL) (Read/Write) ..............................................154

9.2.9 User-defined Register (UDR) (Read/Write)....................................................................155

10. PARALLEL PORT ................................................................................................................... 156

10.1 Printer Interface Logic....................................................................................................... 156

10.2 Enhanced Parallel Port (EPP)........................................................................................... 157

10.2.1 Data Port (Data Swapper)..............................................................................................158

10.2.2 Printer Status Buffer.......................................................................................................159

10.2.3 Printer Control Latch and Printer Control Swapper ........................................................159

10.2.4 EPP Address Port ..........................................................................................................160

10.2.5 EPP Data Port 0-3..........................................................................................................160

10.2.6 EPP Pin Descriptions .....................................................................................................162

10.2.7 EPP Operation ...............................................................................................................162

10.2.7.1. EPP Version 1.9 Operation .............................................................................................................. 163

10.2.7.2. EPP Version 1.7 Operation .............................................................................................................. 163

10.3 Extended Capabilities Parallel (ECP) Port........................................................................ 164

10.3.1 ECP Register and Bit Map .............................................................................................164

10.3.2 Data and ecpAFifo Port..................................................................................................166

10.3.3 Device Status Register (DSR)........................................................................................167

- VIII -

W83627EHF/EF

W83627EHG/EG

10.3.4 Device Control Register (DCR) ......................................................................................167

10.3.5 CFIFO (Parallel Port Data FIFO) Mode = 010................................................................168

10.3.6 ECPDFIFO (ECP Data FIFO) Mode = 011.....................................................................168

10.3.7 TFIFO (Test FIFO Mode) Mode = 110 ...........................................................................168

10.3.8 CNFGA (Configuration Register A) Mode = 111 ............................................................168

10.3.9 CNFGB (Configuration Register B) Mode = 111 ............................................................168

10.3.10 ECR (Extended Control Register) Mode = all.................................................................169

10.3.11 ECP Pin Descriptions.....................................................................................................171

10.3.12 ECP Operation ...............................................................................................................172

10.3.12.1. Mode Switching ..................................................................................................................... 173

10.3.12.2. Command/Data ..................................................................................................................... 173

10.3.12.3. Data Compression................................................................................................................. 173

10.3.13 FIFO Operation ..............................................................................................................173

10.3.14 DMA Transfers ...............................................................................................................175

10.3.15 Programmed I/O (NON-DMA) Mode ..............................................................................175

11. KEYBOARD CONTROLLER................................................................................................... 176

11.1 Output Buffer..................................................................................................................... 176

11.2 Input Buffer........................................................................................................................ 176

11.3 Status Register ................................................................................................................. 177

11.4 Commands........................................................................................................................ 177

11.5 Hardware GATEA20/Keyboard Reset Control Logic........................................................ 180

11.5.1 KB Control Register .......................................................................................................180

11.5.2 Port 92 Control Register.................................................................................................181

12. POWER MANAGEMENT EVENT........................................................................................... 182

12.1 Resume Reset Logic......................................................................................................... 182

12.2 PWROK Generation.......................................................................................................... 183

13. SERIALIZED IRQ.................................................................................................................... 186

13.1 Start Frame ....................................................................................................................... 186

13.2 IRQ/Data Frame................................................................................................................ 187

13.3 Stop Frame ....................................................................................................................... 189

Publication Release Date: April 7 , 2009

-IX- Version 1. 94

W83627EHF/EF

W83627EHG/EG

14. WATCHDOG TIMER............................................................................................................... 190

15. VID INPUTS AND OUTPUTS ................................................................................................. 191

15.1 VID Input Detection........................................................................................................... 191

15.2 VID Output Control............................................................................................................ 191

16. PCI RESET BUFFERS ........................................................................................................... 192

17. CONFIGURATION REGISTER............................................................................................... 193

17.1 Chip (Global) Control Register.......................................................................................... 193

17.2 Logical Device 0 (FDC)..................................................................................................... 201

17.3 Logical Device 1 (Parallel Port)......................................................................................... 206

17.4 Logical Device 2 (UART A) ............................................................................................... 207

17.5 Logical Device 3 (UART B) ............................................................................................... 208

17.6 Logical Device 5 (Keyboard Controller) ............................................................................ 211

17.7 Logical Device 7 (GPIO1, GPIO6, Game Port & MIDI Port)............................................. 212

17.8 Logical Device 8 (WDTO# & PLED) ................................................................................. 216

17.9 Logical Device 9 (GPIO2,GPIO3, GPIO4, GPIO5 & SUSLED) (VSB Power) .................. 218

17.10 Logical Device A (ACPI) ................................................................................... 222

17.11 Logical Device B (Hardware Monitor, for W83627EHF/EHG only) .................. 232

18. SPECIFICATIONS .................................................................................................................. 234

18.1 Absolute Maximum Ratings .............................................................................................. 234

18.2 DC CHARACTERISTICS.................................................................................................. 234

18.3 AC CHARACTERISTICS .................................................................................................. 243

18.3.1 AC Power Failure Resume Timing .................................................................................243

18.3.2 Clock Input Timing .........................................................................................................248

18.3.3 SMBus Timing................................................................................................................250

18.3.4 Floppy Disk Drive Timing ...............................................................................................251

18.3.5 UART/Parallel Port.........................................................................................................252

18.3.5.1. Modem Control Timing ..................................................................................................................... 254

18.3.6 Parallel Port Mode Parameters ......................................................................................255

18.3.7 Parallel Port ...................................................................................................................256

- X -

W83627EHF/EF

W83627EHG/EG

18.3.7.1. Parallel Port Timing .......................................................................................................................... 256

18.3.7.2. EPP Data or Address Read Cycle Timing Parameters .................................................................... 256

18.3.7.3. EPP Data or Address Read Cycle (EPP Version 1.9)...................................................................... 258

18.3.7.4. EPP Data or Address Read Cycle (EPP Version 1.7)...................................................................... 259

18.3.7.5. EPP Data or Address Write Cycle Timing Parameters .................................................................... 260

18.3.7.6. EPP Data or Address Write Cycle (EPP Version 1.9) ...................................................................... 261

18.3.7.7. EPP Data or Address Write Cycle (EPP Version 1.7) ...................................................................... 262

18.3.7.8. Parallel Port FIFO Timing Parameters ............................................................................................. 262

18.3.7.9. Parallel FIFO Timing ........................................................................................................................ 263

18.3.7.10. ECP Parallel Port Forward Timing Parameters ..................................................................... 263

18.3.7.11. ECP Parallel Port Forward Timing......................................................................................... 264

18.3.7.12. ECP Parallel Port Reverse Timing Parameters..................................................................... 264

18.3.7.13. ECP Parallel Port Reverse Timing ........................................................................................ 264

18.3.8 KBC Timing Parameters ................................................................................................265

18.3.8.1. Writing Cycle Timing ........................................................................................................................ 266

18.3.8.2. Read Cycle Timing ........................................................................................................................... 267

18.3.8.3. Send Data to K/B.............................................................................................................................. 267

18.3.8.4. Receive Data from K/B..................................................................................................................... 267

18.3.8.5. Input Clock ....................................................................................................................................... 268

18.3.8.6. Send Data to Mouse......................................................................................................................... 268

18.3.8.7. Receive Data from Mouse................................................................................................................ 268

18.3.9 GPIO Timing Parameters...............................................................................................268

18.3.9.1. GPIO Write Timing ........................................................................................................................... 269

18.4 LPC Timing ....................................................................................................................... 270

18.5 Reset Timing..................................................................................................................... 271

19. TOP MARKING SPECIFICATION .......................................................................................... 272

20. PACKAGE SPECIFICATION .................................................................................................. 273

21. REVISION HISTORY .............................................................................................................. 274

Publication Release Date: April 7 , 2009

-1- Version 1.94

W83627EHF/EF

W83627EHG

1. GENERAL DESCRIPTION

W83627EHF/EHG/EF/EG is an evolving product from Nuvoton's most popular I/O family. They

feature a whole new interface, namely LPC (Low Pin Count) interface, which will be supported in the

new generation chip-set. This interface as its name suggests is to provide an economical

implementation of I/O's interface with lower pin count and still maintains equivalent performance as its

ISA interface counterpart. Approximately 40 pin counts are saved in LPC I/O comparing to ISA

implementation. It is fully transparent in terms of software which means no BIOS or device driver

update is needed except chip-specific configuration.

The disk drive adapter functions of W83627EHF/EHG/EF/EG include a floppy disk drive controller

compatible with the industry standard 82077/ 765, data separator, write pre-compensation circuit,

decode logic, data rate selection, clock generator, drive interface control logic, and interrupt and DMA

logic. The wide range of functions integrated onto the W83627EHF/EHG/EF/EG greatly reduces the

number of components required for interfacing with floppy disk drives. W83627EHF/EHG/EF/EG

supports one 360K, 720K, 1.2M, 1.44M, or 2.88M disk drives and data transfer rates of 250 Kb/s, 300

Kb/s, 500 Kb/s,1 Mb/s, and 2 Mb/s.

W83627EHF/EHG/EF/EG provides two high-speed serial communication ports (UARTs), one of which

supports serial Infrared communication. Each UART includes a 16-byte send/receive FIFO, a

programmable baud rate generator, complete modem control capability, and a processor interrupt

system. Both UARTs provide legacy speed with baud rate up to 115.2k bps and also advanced speed

with baud rates of 230k, 460k, or 921k bps which support higher speed modems. In addition,

W83627EHF/EHG/EF/EG provides IR functions: IrDA 1.0 (SIR for 1.152K bps).

W83627EHF/EHG/EF/EG supports one PC-compatible printer port (SPP), Bi-directional Printer port

(BPP) and also Enhanced Parallel Port(EPP) and Extended Capabilities Port (ECP).And

W83627EHF/EHG/EF/EG contains a Game port and a MIDI port. The game port is designed to support

2 joysticks and can be applied to all standard PC game control devices, they are very important for a

entertainment or consumer computer.

W83627EHF/EHG/EF/EG provides flexible I/O control functions to the system designer through a set of

General Purpose I/O ports. These GPIO ports may serve as simple I/O or may be individually

configured to provide a predefined alternate function.

W83627EHF/EHG supports hardware status monitoring for personal computers. It can be used to

monitor several critical hardware parameters of the system, including power supply voltages, fan

- 2 -

W83627EHF/EF

W83627EHG/EG

speeds, and temperatures, which are very important for a high-end computer system to work stably

and properly. Moreover, W83627EHF/EHG supports the Smart Fan control system, including the

“Thermal CruiseTM” and “Speed CruiseTM” functions. Smart Fan can make system more stable and user

friendly.

W83627EHF/EHG/EF/EG is made to fully comply with Microsoft© PC98 , PC99 and PC2001 System

Design Guide, and meet the requirements of ACPI.

The configuration registers support mode selection, function enable/disable, and power down function

selection. Furthermore, the configurable PnP features are compatible with the plug-and-play feature

demand of Windows 95/98/2000/XPTM, which makes system resource allocation more efficient than

ever.

The special characteristic of Super I/O product line is to avoid power rails short. This is especially true

to a multi-power system where power partition is much more complex than a single-power one. Special

care might be applied during layout stage or the IC will fail even though its intended function is

workable.

Publication Release Date: April 7 , 2009

-3- Version 1.94

W83627EHF/EF

W83627EHG

2. FEATURES

General

• Meet LPC Spec. 1.01

• Support LDRQ#(LPC DMA), SERIRQ (Serial IRQ)

• Integrated Hardware Monitor functions

• Compliant with Microsoft© PC98/PC99/PC2001 System Design Guide

• Support DPM (Device Power Management), ACPI

• Programmable configuration settings

• Single 24 or 48 MHz clock input

• It is 3.3V level but 5V tolerance support

--- Besides LPC function pins(Pin21 ~ Pin30) and H/W monitor analog pins(Pin95 ~ Pin110)

--- Input level can up to 5V and maximum input level can be up to 5V+10%

FDC

• Compatible with IBM PC AT disk drive systems

• Variable write pre-compensation with track selectable capability

• Support vertical recording format

• DMA enable logic

• 16-byte data FIFOs

• Support floppy disk drives and tape drives

• Detects all overrun and underrun conditions

• Built-in address mark detection circuit to simplify the read electronics

• FDD anti-virus functions with software write protect and FDD write enable signal (write data

signal was forced to be inactive)

• Support one 3.5-inch or 5.25-inch floppy disk drive

- 4 -

W83627EHF/EF

W83627EHG/EG

• Completely compatible with industry standard 82077

• 360K/720K/1.2M/1.44M/2.88M format; 250K, 300K, 500K, 1M, 2M bps data transfer rate

• Support 3-mode FDD, and its Windows driver

UART

• Two high-speed 16550 compatible UARTs with 16-byte send/receive FIFOs

• MIDI compatible

• Fully programmable serial-interface characteristics:

--- 5, 6, 7 or 8-bit characters

--- Even, odd or no parity bit generation/detection

--- 1, 1.5 or 2 stop bits generation

• Internal diagnostic capabilities:

--- Loop-back controls for communications link fault isolation

--- Break, parity, overrun, framing error simulation

• Programmable baud rate generator allows division of 1.8461 MHz and 24 MHz by 1 to (216-1)

• Maximum baud rate up to 921k bps for 14.769 MHz and 1.5M bps for 24 MHz

Infrared

• Support IrDA version 1.0 SIR protocol with maximum baud rate up to 115.2K bps

• Support SHARP ASK-IR protocol with maximum baud rate up to 57,600 bps

Parallel Port

• Compatible with IBM parallel port

• Support PS/2 compatible bi-directional parallel port

• Support Enhanced Parallel Port (EPP) - Compatible with IEEE 1284 specification

• Support Extended Capabilities Port (ECP) - Compatible with IEEE 1284 specification

Publication Release Date: April 7 , 2009

-5- Version 1.94

W83627EHF/EF

W83627EHG

• Enhanced printer port back-drive current protection

Game Port

• Support two separate Joysticks

• Support every Joystick two axis (X, Y) and two button (A, B) controllers

MIDI Port

• The baud rate is 31.25 K baud

• 16-byte input FIFO

• 16-byte output FIFO

Keyboard Controller

• 8042 based with optional F/W from AMIKKEYTM-2, Phoenix MultiKey/42TM or customer code

with 2K bytes of programmable ROM, and 256 bytes of RAM

• Asynchronous Access to Two Data Registers and One status Register

• Software compatibility with the 8042

• Support PS/2 mouse

• Support port 92

• Support both interrupt and polling modes

• Fast Gate A20 and Hardware Keyboard Reset

• 8 Bit Timer/ Counter

• Support binary and BCD arithmetic

• 6 MHz, 8 MHz, 12 MHz, or 16 MHz operating frequency

General Purpose I/O Ports

• 48 programmable general purpose I/O ports

- 6 -

W83627EHF/EF

W83627EHG/EG

• GPIO port 1 and 4 can not only serve as simple I/O ports but also watch dog timer output,

Power LED output, Suspend LED output

• Functional in power down mode (GP24 ~ GP27, GPIO-3, GPIO-4, GPIO-5)

OnNow Functions

• Keyboard Wake-Up by programmable keys

• Mouse Wake-Up by programmable buttons

• On Now Wake-Up from all of the ACPI sleeping states (S1-S5)

Hardware Monitor Functions (For W83627EHF/EHG only)

• Smart Fan control system, support SMART FANTM I - “Thermal CruiseTM” and “Speed

CruiseTM” Mode , SMART FANTM III function

• 3 thermal inputs from optionally remote thermistors or PentiumTM II/III/4 thermal diode output

• 10 voltage inputs (CPUVCORE, VIN[0..4] and intrinsic 3VCC, AVCC , 3VSB, VBAT)

• 5 fan speed monitoring inputs

• 4 fan speed control

• Dual mode for fan control (PWM & DC)

• Build in case open detection circuit

• Programmable hysteresis and setting points for all monitored items

• Over temperature indicate output

• Issue SMI#, OVT# to activate system protection

• Nuvoton Hardware DoctorTM support

• 6 VID inputs / outputs

• Provide I2C interface to read/write registers

Package

Publication Release Date: April 7 , 2009

-7- Version 1.94

W83627EHF/EF

W83627EHG

• 128-pin PQFP

3. BLOCK DIAGRAM

LRESET#, LCLK, LFRAME#, LAD[3:0], LDRQ#, SERIRQ

LPC Interface

FDC

URA

PRT

MIDI

GPIO

Floppy drive

interface signals

Serial port A, B

interface signals

Printer port

interface signals

CPI

Joystick interface

signals

General-purpose

I/O pins

MSI

MSO

KBC

Keyboard/Mouse

data and clock

Game

Port

IRRX

IRTX

W83627EF/EG

- 8 -

W83627EHF/EF

W83627EHG/EG

LRESET#, LCLK, LFRAME#, LAD[3:0], LDRQ#, SERIRQ

LPC Interface

FDC

URA

PRT

MIDI

GPIO IR

Floppy drive

interface signals

Serial port A, B

interface signals

Printer port

interface signals

CPI

Joystick interface

signals

General-purpose

I/O pins

MSI

MSO

Hardware monitor

channel and Vref

KBC

Keyboard/Mouse

data and clock

Game

Port

IRRX

IRTX

W83627EHF/EHG

Publication Release Date: April 7 , 2009

-9- Version 1.94

W83627EHF/EF

W83627EHG

4. PIN CONFIGURATION

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

AUXFANIN1

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

AUXTIN

VREF

CPUVCORE

VIN0

VIN1

VIN2

VIN3

VIN4

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#/SCL

GP33/RSTOUT3#/SDA

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

CASEOPEN#

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

CPUTIN

SYSTIN

VID5

VID4

VID3

VID2

VID1

VID0

AUXFANIN0

CPUFANIN0

SYSFANIN

AVCC

CPUFANOUT0

SYSFANOUT

AGND

BEEP

GP21/CPUFANIN1/MSI

GP20/CPUFANOUT1/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

SMI#/OVT#

DSA#

AUXFANOUT

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627EHF/EHG

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

AVCC 3VSB 3VSB

3VCC

VBAT

3VCC

AVCC

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

AUXFANIN1

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

AUXTIN

VREF

CPUVCORE

VIN0

VIN1

VIN2

VIN3

VIN4

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#/SCL

GP33/RSTOUT3#/SDA

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

CASEOPEN#

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

CPUTIN

SYSTIN

VID5

VID4

VID3

VID2

VID1

VID0

AUXFANIN0

CPUFANIN0

SYSFANIN

AVCC

CPUFANOUT0

SYSFANOUT

AGND

BEEP

GP21/CPUFANIN1/MSI

GP20/CPUFANOUT1/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

SMI#/OVT#

DSA#

AUXFANOUT

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627EHF/EHG

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

AVCC 3VSB 3VSB

3VCC

VBAT

3VCC

AVCC

Pin Layout for W83627EHF/EHG

- 10 -

W83627EHF/EF

W83627EHG/EG

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#

GP33/RSTOUT3#

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

GND

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

3VCC

GND

GP21/MSI

GP20/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

DSA#

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627HF/HG

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

3VCC 3VSB 3VSB

3VCC

VBAT

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#

GP33/RSTOUT3#

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

GND

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

3VCC

GND

GP21/MSI

GP20/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

DSA#

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627EF/EG

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

3VCC 3VSB 3VSB

3VCC

VBAT

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#

GP33/RSTOUT3#

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

GND

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

3VCC

GND

GP21/MSI

GP20/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#

GP33/RSTOUT3#

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

GND

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

3VCC

GND

GP21/MSI

GP20/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

DSA#

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627HF/HG

DRVDEN0

GP23

INDEX#

MOA#

DSA#

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627HF/HG

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

3VCC 3VSB 3VSB

3VCC

VBAT

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

3VCC 3VSB 3VSB

3VCC

VBAT

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#

GP33/RSTOUT3#

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP37

KDAT/GP26

KCLK/GP27

3VSB

KBRST#

GA20M

RIA#/GP60

DCDA#/GP61

GND

SOUTA/GP62(PENKBC)

SINA/GP63

DTRA#/GP64

RTSA#/GP65(HEFRAS)

DSRA#/GP66

CTSA#/GP67

3VCC

STB#

AFD#

ERR#

INIT#

SLIN#

PD0

PD1

PD2

PD3

RSTOUT0#

RSTOUT1#

GP30

GP31

GP32/RSTOUT2#

GP33/RSTOUT3#

GP34/RSTOUT4#

GP35

PME#

GP40/RIB#

GP41/DCDB#

GP42/SOUTB/IRTX

GP43/SINB/IRRX

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

GND

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

3VCC

GND

GP21/MSI

GP20/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

GP44/DTRB#

GP45/RTSB#

GP46/DSRB#

GP47/CTSB#

GP50/WDTO#(EN_VRM10)

GND

RSMRST#/GP51

VBAT

SUSB#/GP52

PSON#/GP53

PWROK/GP54

GP55/SUSLED

GP36

PSIN#/GP56

PSOUT#/GP57

MDAT/GP24

MCLK/GP25

3VCC

GND

GP21/MSI

GP20/MSO

GP17/GPSA2

GP16/GPSB2

GP15/GPY1

GP14/GPY2

GP13/GPX2

GP12/GPX1

GP11/GPAB1

GP10/GPSA1

DRVDEN0

GP23

INDEX#

MOA#

DSA#

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627EF/EG

DSA#

DIR#

STEP#

WD#

WE#

3VCC

TRAK0#

WP#

RDATA#

HEAD#

DSKCHG#

IOCLK

GP22

GND

PCICLK

LDRQ#

SERIRQ

LAD3

LAD2

LAD1

LAD0

3VCC

LFRAME#

LRESET#

SLCT

BUSY

ACK#

PD7

PD6

PD5

PD4

W83627EF/EG

102

101

100

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

3VCC 3VSB 3VSB

3VCC

VBAT

Pin Layout for W83627EF/EG

Publication Release Date: April 7 , 2009

-11- Version 1.94

W83627EHF/EF

W83627EHG

5. PIN DESCRIPTION

Note: Please refer to Section 18.2 DC CHARACTERISTICS for details.

AOUT - Analog output pin

AIN - Analog input pin

INcs - CMOS level Schmitt-triggered input pin

INt - TTL level input pin

INtd - TTL level input pin with internal pull down resistor

INts - TTL level Schmitt-triggered input pin

INtsp3 - 3.3V TTL level Schmitt-triggered input pin

INtu - TTL level input pin with internal pull up resistor

INtsu - TTL level Schmitt-triggered input pin with internal pull up resistor

I/O8t - TTL level bi-directional pin with 8 mA source-sink capability

I/O12t -3.3V TTL level bi-directional pin with 12 mA source-sink capability

I/OD12ts - 3.3V TTL level bi-directional Schmitt-triggered pin. Open-drain output with 12 mA sink capability

I/OD16cs - CMOS level Schmitt-triggered bi-directional pin. Open-drain output with 16 mA sink capability

I/OD24t - TTL level bi-directional pin. Open-drain output with 24 mA sink capability

OUT8 - TTL level output pin with 8 mA source-sink capability

OUT12 -3.3V TTL level output pin with 12 mA source-sink capability

OUT24 - TTL level output pin with 24 mA source-sink capability

OD8 - Open-drain output pin with 8 mA sink capability

OD12 - Open-drain output pin with 12 mA sink capability

OD24 - Open-drain output pin with 24 mA sink capability

5.1 LPC Interface

SYMBOL PIN I/O FUNCTION

IOCLK 18 INt System clock input, which is selective by the register according to

the input frequency either 24MHz or 48MHz. Default is 48MHz.

PME# 86 OUT12 Generated PME event.

- 12 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

PCICLK 21 INt PCI clock 33 MHz input.

LDRQ# 22

OUT12 Encoded DMA Request signal.

SERIRQ 23 I/O12t Serial IRQ Input/Output.

LAD[3:0] 24-27 I/O12t These signal lines communicate address, control, and data

information over the LPC bus between a host and a peripheral.

LFRAME# 29 INt Indicates start of a new cycle or termination of a broken cycle.

LRESET# 30 INt Reset signal. It can connect to PCIRST# signal on the host.

5.2 FDC Interface

SYMBOL PIN I/O FUNCTION

DRVDEN0 1 OD24 Drive Density Select bit 0.

INDEX# 3 INcsu

This Schmitt-triggered input from the disk drive is active low when the head

is positioned over the beginning of a track marked by an index hole. This

input pin can be pulled up internally by a 1 KΩ(±50%). The resistor also

can be disabled/enabled by bit 7 of LD0-CRF0(FIPURDWN). Default is

disabled.

MOA# 4 OD24 Motor A On. When set to 0, this pin enables disk drive 0. This is an open

drain output.

DSA# 6 OD24 Drive Select A. When set to 0, this pin enables disk drive A. This is an open

drain output.

DIR# 8 OD24

Direction of the head step motor. An open drain output.

Logic 1 = outward motion

Logic 0 = inward motion

STEP# 9 OD24 Step output pulses. This active low open drain output produces a pulse to

move the head to another track.

Publication Release Date: April 7 , 2009

-13- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

WD# 10 OD24 Write data. This logic low open drain writes pre-compensation serial data

to the selected FDD. An open drain output.

WE# 11 OD24 Write enable. An open drain output.

TRAK0# 13 INtsu

Track 0. This Schmitt-triggered input from the disk drive is active low

when the head is positioned over the outermost track. This input pin

can be pulled up internally by a 1 KΩ(±50%). The resistor also can be

disabled/enabled by bit 7 of LD0-CRF0(FIPURDWN). Default is disabled.

WP# 14 INtsu

Write protected. This active low Schmitt input from the disk drive

indicates that the diskette is write-protected. This input pin can be pulled

up internally by a 1 KΩ(±50%). The resistor also can be disabled/enabled

by bit 7 of LD0-CRF0(FIPURDWN). Default is disabled.

RDATA# 15 INtsu

The read data input signal from the FDD. This input pin can be pulled up

internally by a 1 KΩ(±50%). The resistor also can be disabled/enabled by

bit 7 of LD0-CRF0(FIPURDWN). Default is disabled.

HEAD# 16 OD24

Head select. This open drain output determines which disk drive head is

active.

Logic 1 = side 0

Logic 0 = side 1

DSKCHG# 17 INtsu

Diskette change. This signal is active low at power on and whenever the

diskette is removed. This input pin can be pulled up internally by a 1 KΩ(±

50%) . The resistor also can be disabled / enabled by bit 7 of LD0-CRF0

(FIPURDWN). Default is disabled.

- 14 -

W83627EHF/EF

W83627EHG/EG

5.3 Multi-Mode Parallel Port

SYMBOL PIN I/O FUNCTION

SLCT 31

INts

PRINTER MODE:

An active high input on this pin indicates that the printer is

selected. Refer to the description of the parallel port for definition

of this pin in ECP and EPP mode.

PE 32

INts

PRINTER MODE:

An active high input on this pin indicates that the printer has

detected the end of the paper. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

BUSY 33

INts

PRINTER MODE:

An active high input indicates that the printer is not ready to

receive data. Refer to the description of the parallel port for

definition of this pin in ECP and EPP mode.

ACK# 34

INts

PRINTER MODE: ACK#

An active low input on this pin indicates that the printer has

received data and is ready to accept more data. Refer to the

description of the parallel port for the definition of this pin in ECP

and EPP mode.

ERR# 45

INts

PRINTER MODE: ERR#

An active low input on this pin indicates that the printer has

encountered an error condition. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

SLIN# 43

OD12

/OUT12

PRINTER MODE: SLIN#

Output line for detection of printer selection. Refer to the

description of the parallel port for the definition of this pin in ECP

and EPP mode.

Publication Release Date: April 7 , 2009

-15- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

INIT# 44

OD12

/OUT12

PRINTER MODE: INIT#

Output line for the printer initialization. Refer to the description of

the parallel port for the definition of this pin in ECP and EPP

mode.

AFD# 46

OD12

/OUT12

PRINTER MODE: AFD#

An active low output from this pin causes the printer to auto feed a

line after a line is printed. Refer to the description of the parallel

port for the definition of this pin in ECP and EPP mode.

STB# 47

OD12

/OUT12

PRINTER MODE: STB#

An active low output is used to latch the parallel data into the

printer. Refer to the description of the parallel port for the

definition of this pin in ECP and EPP mode.

PD0 42 I/O12ts

PRINTER MODE: PD0

Parallel port data bus bit 0. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

PD1 41

I/O12ts

PRINTER MODE: PD1

Parallel port data bus bit 1. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

PD2 40

I/O12ts

PRINTER MODE: PD2

Parallel port data bus bit 2. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

PD3 39

I/O12ts

PRINTER MODE: PD3

Parallel port data bus bit 3. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

PD4 38

I/O12ts

PRINTER MODE: PD4

Parallel port data bus bit 4. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

- 16 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

PD5 37

I/O12ts

PRINTER MODE: PD5

Parallel port data bus bit 5. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

PD6 36 I/O12ts

PRINTER MODE: PD6

Parallel port data bus bit 6. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

PD7 35 I/O12ts

PRINTER MODE: PD7

Parallel port data bus bit 7. Refer to the description of the

parallel port for the definition of this pin in ECP and EPP mode.

5.4 Serial Port & Infrared Port Interface

SYMBOL PIN I/O FUNCTION

CTSA# INt

Clear To Send. It is the modem control input. The function of

these pins can be tested by reading bit 4 of the handshake status

GP67

I/OD12t General purpose I/O port 6 bit 7.

CTSB# INt

Clear To Send. It is the modem control input. The function of

these pins can be tested by reading bit 4 of the handshake status

GP47***

I/OD12t General purpose I/O port 4 bit 7.

DSRA# INt

Data Set Ready. An active low signal indicates the modem or

data set is ready to establish a communication link and transfer

data to the UART.

GP66

I/OD12t General purpose I/O port 6 bit 6.

Publication Release Date: April 7 , 2009

-17- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

DSRB# INt

Data Set Ready. An active low signal indicates the modem or

data set is ready to establish a communication link and transfer

data to the UART.

GP46*

I/OD12t General purpose I/O port 4 bit 6.

RTSA# OUT8 UART A Request To Send. An active low signal informs the

modem or data set that the controller is ready to send data.

HEFRAS INtd

During power-on reset, this pin is pulled down internally(20K±30%)

and is defined as HEFRAS, which provides the power-on value

for CR26 bit 6 (HEFRAS). A 1 kΩ is reserved to pull down and a 1

kΩ is recommended if intends to pull up. (select 4EH as

configuration I/O port′s address)

GP65

I/O8 General purpose I/O port 6 bit 5.

RTSB# OUT12 UART B Request To Send. An active low signal informs the

modem or data set that the controller is ready to send data.

GP45***

I/OD12t General purpose I/O port 4 bit 5.

DTRA# OUT8 UART A Data Terminal Ready. An active low signal informs the

modem or data set that the controller is ready to communicate.

GP64

I/O8 General purpose I/O port 6 bit 4.

DTRB# OUT12 UART B Data Terminal Ready. An active low signal informs the

modem or data set that controller is ready to communicate.

GP44*

I/OD12t General purpose I/O port 4 bit 4.

SINA INt Serial Input. It is used to receive serial data through the

communication link.

GP63

I/OD12 General purpose I/O port 6 bit 3.

SINB 82 INt Serial Input. It is used to receive serial data through the

communication link.

- 18 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

IRRX IR Receiver input.

GP43*** I/OD12 General purpose I/O port 4 bit 3.

SOUTA OUT8 UART A Serial Output. It is used to transmit serial data out to the

communication link.

PENKBC INtd

During power on reset, this pin is pulled down internally(20K ±

30%)and is defined as PENKBC, which provides the power on

value for CR24 bit 2. A 1 kΩ is reserved to pull down and a 1 kΩ is

recommended if intends to pull up.

GP62

I/O8 General purpose I/O port 6 bit 2.

SOUTB UART B Serial Output. It is used to transmit serial data out to the

communication link.

IRTX

OUT12

IR Transmitter output.

GP42*

I/OD12 General purpose I/O port 4 bit 2.

DCDA# INt Data Carrier Detect. An active low signal indicates the modem

or data set has detected a data carrier.

GP61

I/OD12 General purpose I/O port 6 bit 1.

DCDB# INt Data Carrier Detect. An active low signal indicates the modem

or data set has detected a data carrier.

GP41***

I/OD12 General purpose I/O port 4 bit 1.

RIA# 57

INt Ring Indicator. An active low signal indicates that a ring signal is

being received from the modem or data set.

GP60 57

I/OD12 General purpose I/O port 6 bit 0.

RIB# INt Ring Indicator. An active low signal indicates that a ring signal is

being received from the modem or data set.

GP40*

I/OD12 General purpose I/O port 4 bit 0.

Publication Release Date: April 7 , 2009

-19- Version 1.94

W83627EHF/EF

W83627EHG

Note. The * sign see 5.10.8 GPIO-1 and GPIO-4 with WDTO# / SUSLED / PLED multi-function

5.5 KBC Interface

SYMBOL PIN I/O FUNCTION

GA20M 59 OUT12 Gate A20 output. This pin is high after system reset. (KBC P21)

KBRST# 60 OUT12 Keyboard reset. This pin is high after system reset. (KBC P20)

KCLK I/OD16ts Keyboard Clock.

GP27

I/OD16t General purpose I/O port 2 bit 7.

KDAT I/OD16ts Keyboard Data.

GP26

I/OD16t General purpose I/O port 2 bit 6.

MCLK I/OD16ts PS2 Mouse Clock.

GP25

I/OD16t General purpose I/O port 2 bit 5.

MDAT I/OD16ts PS2 Mouse Data.

GP24

I/OD16t General purpose I/O port 2 bit 4.

5.6 Hardware Monitor Interface

SYMBOL PIN I/O FUNCTION

BEEP 118 OD8 Beep function for hardware monitor. This pin is low after system

reset. (for H version only, C version is tri-state)

CASEOPEN# 76 INt

CASE OPEN detected. An active low level input from an

external device when case is opened. This signal can be latched

if pin VBAT is connect to battery, even W83627EHF/EHG is

power off. This pin is VSS for W83627EF/EG.Pull down is

recommended if useless.

(For H version only, C version is falling edge trig ger only)

VIN4 95 AIN 0V to 2.048V FSR Analog Inputs. (FSR: Full Scale Register)

- 20 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

VIN3 96 AIN 0V to 2.048V FSR Analog Inputs.

VIN2 97 AIN 0V to 2.048V FSR Analog Inputs.

VIN1 98 AIN 0V to 2.048V FSR Analog Inputs.

VIN0 99 AIN 0V to 2.048V FSR Analog Inputs.

CPUVCORE 100 AIN 0V to 2.048V FSR Analog Inputs.

VREF 101 AOUT Reference Voltage (2.048V) for temperature maturation.

AUXTIN 102 AIN

Temperature sensor 3 inputs. It is used for temperature

maturation.

CPUTIN 103 AIN

Temperature sensor 2 inputs. It is used for CPU temperature

maturation.

SYSTIN 104 AIN

Temperature sensor 1 input. It is used for system temperature

maturation.

OVT# OD12 Over temperature Shutdown Output. It indicated the temperature

is over temperature limit.

SMI#

OD12

System Management Interrupt channel output.

(Default after PCIRST)

VID5

VID4

VID3

VID2

VID1

VID0

105

106

107

108

109

110

I/O12 VID input detect, also with output control.

AUXFANIN1 58 I/O12ts 0V to +3.3V amplitude fan tachometer input.

AUXFANIN0 111 I/O12ts 0V to +3.3V amplitude fan tachometer input.

Publication Release Date: April 7 , 2009

-21- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

CPUFANIN0 112

SYSFANIN 113

CPUFANIN1 I/O12ts 0V to +3.3V amplitude fan tachometer input. (Default)

MSI INts MIDI serial data input.

GP21

119

I/OD12ts General purpose I/O port 2 bit 1.

AUXFANOUT 7

CPUFANOUT0 115

SYSFANOUT 116

AOUT/

OD12

DC/PWM fan output control.

CPUFANOUT0 & AUXFANOUT are default PWM Mode,

CPUFANOUT1 & SYSFANOUT are default DC Mode.

(For H version, while SYSFANOUT or CPUFANOUT0 be

selected to PWM Mode, either of them can be open-drain or

push-pull output. The controlled bits are CR24h bit[4:3].

Open-drain output is default.)

CPUFANOUT1 AOUT/

OUT12t

DC/PWM fan output control.

CPUFANOUT0 & AUXFANOUT are default PWM Mode,

CPUFANOUT1 & SYSFANOUT are default DC Mode.

MSO OUT12t MIDI serial data output.

GP20

120

I/OD12t General purpose I/O port 2 bit 0.

5.7 Game Port & MIDI Port

SYMBOL PIN I/O FUNCTION

GPSA1 INts Active-low, Joystick I switch input 1. (Default)

GP10*

128

I/OD12ts General purpose I/O port 1 bit 0.

GPSB1 INts Active-low, Joystick II switch input 1. (Default)

GP11**

127

I/OD12ts General purpose I/O port 1 bit 1.

- 22 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

GPX1 Joystick II timer pin. This pin connects to X positioning

variable resistors for the Joystick. (Default)

GP12*

126 I/OD12ts

General purpose I/O port 1 bit 2.

GPX2 Joystick II timer pin. This pin connects to X positioning

variable resistors for the Joystick. (Default)

GP13**

125 I/OD12ts

General purpose I/O port 1 bit 3.

GPY2 Joystick II timer pin. This pin connects to Y positioning

variable resistors for the Joystick. (Default)

GP14*

124 I/OD12ts

General purpose I/O port 1 bit 4.

GPY1 Joystick I timer pin. This pin connects to Y positioning variable

resistors for the Joystick. (Default)

GP15**

123 I/OD12ts

General purpose I/O port 1 bit 5.

GPSB2 INts Active-low, Joystick II switch input 2. (Default)

GP16*

122

I/OD12ts General purpose I/O port 1 bit 6.

GPSA2 INts Active-low, Joystick I switch input 2. (Default)

GP17**

121

I/OD12ts General purpose I/O port 1 bit 7.

MSI INts MIDI serial data input. (Default)

CPUFANIN1 I/O12ts 0V to +3.3V amplitude fan tachometer input.

GP21

119

I/OD12ts General purpose I/O port 2 bit 1.

MSO 120 OUT12t MIDI serial data output. (Default)

Publication Release Date: April 7 , 2009

-23- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

CPUFANOUT1 AOUT/

OUT12t

DC/PWM fan output control.

CPUFANOUT0 & AUXFANOUT are default PWM Mode,

CPUFANOUT1 & SYSFANOUT are default DC Mode.

GP20 I/OD12t General purpose I/O port 2 bit 0.

Note. The * sign see 5.10.8 GPIO-1 and GPIO-4 with WDTO# / SUSLED / PLED multi-function

5.8 ACPI Interface

SYMBOL PIN I/O FUNCTION

PSIN INtd Panel Switch Input. This pin is high active with an internal pull

down resistor.

GP56

I/OD12t General purpose I/O port 5 bit 6.

PSOUT# OD12 Panel Switch Output. This signal is used for Wake-Up system

from S5cold state. This pin is pulse output, active low.

GP57

I/OD12t General purpose I/O port 5 bit 7.

VBAT 74 PWR +3.3V on-board battery for the digital circuitry.

RSTOUT0# 94 OD12 Secondary LRESET# output 0.

RSTOUT1# 93 OUT12 Secondary LRESET# output 1.

RSTOUT2# OUT12 Secondary LRESET# output 2.

GP32 I/OD12t General purpose I/O port 3 bit 2.

SCL

INt Serial Bus clock.

RSTOUT3# OUT12 Secondary LRESET# output 3.

GP33 I/OD12t General purpose I/O port 3 bit 3.

SDA

I/OD12t Serial bus bi-directional Data.

RSTOUT4# 88 OUT12 Secondary LRESET# output 4.

- 24 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

GP34 I/OD12t General purpose I/O port 3 bit 4.

5.9 General Purpose I/O Port

5.9.1 GPIO Power Source

SYMBOL POWER SOURCE

GPIO port 1 3VCC

GPIO port 2 (Bit0-3) 3VCC

GPIO port 2 (Bit4-7) 3VSB

GPIO port 3 3VSB

GPIO port 4 3VSB

GPIO port 5 3VSB

GPIO port 6 3VCC

5.9.2 GPIO-1 Interface

see 5.7 Game Port

5.9.3 GPIO-2 Interface

SYMBOL PIN I/O FUNCTION

GP20 I/OD12t General purpose I/O port 2 bit 0.

CPUFANOUT1 AOUT/

OUT12

DC/PWM fan output control.

CPUFANOUT0 & AUXFANOUT are default PWM Mode,

CPUFANOUT1 & SYSFANOUT are default DC Mode.

MSO

120

OUT12 MIDI serial data output. (Default)

GP21 I/OD12ts General purpose I/O port 2 bit 1.

CPUFANIN1

119

I/O12ts 0V to +3.3V amplitude fan tachometer input.

Publication Release Date: April 7 , 2009

-25- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

MSI INts MIDI serial data input. (Default)

GP22 19 I/OD12t General purpose I/O port 2 bit 2.

GP23 2 I/OD12t General purpose I/O port 2 bit 3.

GP24 I/OD16t General purpose I/O port 2 bit 4.

MDAT

I/OD16ts PS2 Mouse Data.

GP25 I/OD16t General purpose I/O port 2 bit 5.

MCLK

I/OD16ts PS2 Mouse Clock.

GP26 I/OD16t General purpose I/O port 2 bit 6.

KDAT

I/OD16ts Keyboard Data.

GP27 I/OD16t General purpose I/O port 2 bit 7.

KCLK

I/OD16ts Keyboard Clock.

5.9.4 GPIO-3 Interface

SYMBOL PIN I/O FUNCTION

GP30 92 I/OD12t General purpose I/O port 3 bit 0.

GP31 91 I/OD12t General purpose I/O port 3 bit 1

GP32 I/OD12t General purpose I/O port 3 bit 2.

RSTOUT2# OUT12 Secondary LRESET# output 2.

SCL

INt Serial Bus clock.

GP33 I/OD12t General purpose I/O port 3 bit 3.

RSTOUT3# OUT12 Secondary LRESET# output 3.

SDA

I/OD12t Serial bus bi-directional Data.

- 26 -

W83627EHF/EF

W83627EHG/EG

SYMBOL PIN I/O FUNCTION

GP34 I/OD12t General purpose I/O port 3 bit 4.

RSTOUT4#

OUT12 Secondary LRESET# output 4.

GP35 87 I/OD12t General purpose I/O port 3 bit 5

GP36 69 I/OD12ts General purpose I/O port 3 bit 6

GP37 64 I/OD12ts General purpose I/O port 3 bit 7

5.9.5 GPIO-4 Interface

see 5.4 Serial Port B

5.9.6 GPIO-5 Interface

SYMBOL PIN I/O FUNCTION

GP50 I/O12t General purpose I/O port 5 bit 0.

EN_VRM10 INtd

During VSB power reset (RSMRST), this pin is pulled down

internally and is defined as VID transition voltage level, which

provides the value for CR2C bit 3. A 1 kΩ is reserved to pull down

and a 1 kΩ is recommended if intends to pull up.

WDTO#

OUT12 Watchdog timer output signal.

GP51 I/OD12t General purpose I/O port 5 bit 1.

RSMRST#

OD12 Resume reset signal output.

GP52 I/OD12t General purpose I/O port 5 bit 2.

SUSB#

INt System S3 states input.

GP53 I/OD12t General purpose I/O port 5 bit 3.

PSON#

OD12 This pin generates the PWRCTL# signal while the power failure.

GP54 I/OD12t General purpose I/O port 5 bit 4.

PWROK

OD12 This pin generates the PWROK signal while the VCC come in.

Publication Release Date: April 7 , 2009

-27- Version 1.94

W83627EHF/EF

W83627EHG

SYMBOL PIN I/O FUNCTION

GP55 I/O12t General purpose I/O port 5 bit 5. (This pin is push-pull output

mode)

SUSLED

OUT12 Suspended LED output. (This pin is push-pull output mode)

GP56 I/OD12t General purpose I/O port 5 bit 6.

PSIN

INtd Panel Switch Input. This pin is high active with an internal pull

down resistor.

GP57 I/OD12t General purpose I/O port 5 bit 7.

PSOUT#

OD12 Panel Switch Output. This signal is used for Wake-Up system

from S5cold state. This pin is pulse output, active low.

5.9.7 GPIO-6 Interface

see 5.4 Serial Port A

5.9.8 GPIO-1 and GPIO-4 with WDTO# / SUSLED / PLED multi-function

SYMBOL PIN I/O FUNCTION

GPxx* I/OD12t

WDTO#

---

OD12

This GPxx* can be served GPIO or Watchdog timer output

signal.

GPxx** I/OD12t

PLED

---

OD12

This GPxx** can be served GPIO or Power LED output signal.

GPxx*** I/OD12t

SUSLED

---

OD12

This GPxx*** can be served GPIO or Suspend LED output

signal.

5.10 POWER PINS

SYMBOL PIN FUNCTION

3VSB 61 +3.3V stand-by power supply for the digital circuitry.

VBAT 74 +3V on-board battery for the digital circuitry.

3VCC 12,28,48 +3.3V power supply for driving 3V on host interface.

- 28 -

W83627EHF/EF

W83627EHG/EG

AVCC 114

Analog +3.3V power input. Internally supplier to all analog

circuitry.

AGND 117

Internally connected to all analog circuitry. The ground reference

for all analog inputs.

GND 20,55 Ground.

Publication Release Date: April 7 , 2009

-29- Version 1.94

W83627EHF/EF

W83627EHG

6. CONFIGURATION REGISTER ACCESS PROTOCOL

The W83627EHF/EHG/EF/EG uses Super I/O protocol to access configuration registers to set up

different types of configurations. The W83627EHF/EHG/EF/EG has totally twelve Logical Devices

(from Logical Device 0 to Logical Device B with the exception of Logical Device 4 for backward

compatibility) corresponding to twelve individual functions: FDC (Logical Device 0), Parallel Port

(Logical Device 1), UARTA (Logical Device 2), UARTB (Logical Device 3), Keyboard Controller

(Logical Device 5), GPIO1, GPIO6, Game Port & MIDI Port(Logical Device 7), WDTO# & PLED

(Logical Device 8), GPIO2, 3, 4, 5 & SUSLED (Logical Device 9), ACPI (Logical Device A), and

Hardware Monitor (Logical Device B),. Each Logical Device has its own configuration registers (above

CR30). The host can access those registers by writing an appropriate Logical Device Number into the

Logical Device select register at CR7.

Logical Device No.

Logical Device

Control

Logical Device

Configuration

One Per

Logical Device

Logical Device No.

Logical Device

Control

Logical Device

Configuration

One Per

Logical Device

Devices of I/O Base Address

LOGICAL DEVICE

NUMBER

FUNCTION I/O BASE ADDRESS

0 FDC 100h ~ FF8h

1 Parallel Port 100h ~ FF8h

2 UART A 100h ~ FF8h

- 30 -

W83627EHF/EF

W83627EHG/EG

LOGICAL DEVICE

NUMBER

FUNCTION I/O BASE ADDRESS

3 UART B 100h ~ FF8h

4 Reserved

5 Keyboard Controller 100h ~ FFFh

6 Reserved

7 GPIO1, GPIO 6, Game Port & MIDI port 100h ~ FFFh

8 WDTO# & PLED Reserved

9 GPIO 2, 3, 4, 5 & SUSLED Reserved

A ACPI Reserved

B Hardware Monitor 100h ~ FFEh

6.1 Configuration Sequence

Wait for key string

Power-on Reset

Check Pass key

Is the data

“87h”?

I/O Write to 2Eh

Extended Function

Mode

Wait for key string

Power-on Reset

Check Pass key

Is the data

“87h”?

Is the data

“87h”?

I/O Write to 2Eh

Any other I/O transition cycle

Wait for key string

Power-on Reset

Check Pass key

Is the data

“87h”?

I/O Write to 2Eh

Extended Function

Mode

Wait for key string

Power-on Reset

Check Pass key

Is the data

“87h”?

Is the data

“87h”?

I/O Write to 2Eh

Any other I/O transition cycle

Publication Release Date: April 7 , 2009

-31- Version 1.94

W83627EHF/EF

W83627EHG

To program the W83627EHF/EHG/EF/EG configuration registers, the following configuration

procedures must be followed in sequence:

(1). Enter the Extended Function Mode.

(2). Configure the configuration registers.

(3). Exit the Extended Function Mode.

6.1.1 Enter the Extended Function Mode

To place the chip into the Extended Function Mode, two successive writes of 0x87 must be applied to

Extended Function Enable Registers (EFERs, i.e. 2Eh or 4Eh).

6.1.2 Configure the Configuration Registers

The chip selects the Logical Device and activates the desired Logical Devices through Extended

Function Index Register (EFIR) and Extended Function Data Register (EFDR). The EFIR is located at

the same address as the EFER, and the EFDR is located at address (EFIR+1).

First, write the Logical Device Number (i.e. 0x07) to the EFIR and then write the number of the desired

Logical Device to the EFDR. If accessing the Chip (Global) Control Registers, this step is not required.

Secondly, write the address of the desired configuration register within the Logical Device to the EFIR

and then write (or read) the desired configuration register through the EFDR.

6.1.3 Exit the Extended Function Mode

To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the

Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode.

6.1.4 Software Programming Example

The following example is written in Intel 8086 assembly language. It assumes that the EFER is located

at 2Eh, so the EFIR is located at 2Eh and the EFDR is located at 2Fh. If the HEFRAS (CR26 bit 6) is

set, 2Eh can be directly replaced by 4Eh and 2Fh replaced by 4Fh.

;-----------------------------------------------------

; Enter the Extended Function Mode

;-----------------------------------------------------

MOV DX, 2EH

MOV AL, 87H

OUT DX, AL

- 32 -

W83627EHF/EF

W83627EHG/EG

OUT DX, AL

;-----------------------------------------------------------------------------

; Configure Logical Device 1, Configuration Register CRF0

;-----------------------------------------------------------------------------

MOV DX, 2EH

MOV AL, 07H

OUT DX, AL ; point to Logical Device Number Reg.

MOV DX, 2FH

MOV AL, 01H

OUT DX, AL ; select Logical Device 1

;

MOV DX, 2EH

MOV AL, F0H

OUT DX, AL ; select CRF0

MOV DX, 2FH

MOV AL, 3CH

OUT DX, AL ; update CRF0 with value 3CH

;----------------------------------------------------------------------------

; Exit the Extended Function Mode

;----------------------------------------------------------------------------

MOV DX, 2EH

MOV AL, AAH

OUT DX, AL

Chip (Global) Control Registers

INDEX R/W DEFAULT VALUE DESCRIPTION

02h Write Only Software Reset

07h R/W 00h Logical Device

20h Read Only A0h Chip ID, MSB

21h Read Only 2xh Chip ID, LSB

22h R/W FFh Device Power Down

23h R/W 00h Immediate Power Down

24h R/W 0100_0ss0b Global Option

25h R/W 00h Interface Tri-state Enable

26h R/W 0s000000b Global Option

27h Reserved

Publication Release Date: April 7 , 2009

-33- Version 1.94

W83627EHF/EF

W83627EHG

INDEX R/W DEFAULT VALUE DESCRIPTION

28h R/W 50h Global Option

29h R/W 00h Multi-function Pin Selection

2Ah R/W 00h I2C pin select

2Bh Reserved

2Ch R/W E2h Multi-function Pin Selection

2Dh R/W 21h Multi-function Pin Selection

2Eh R/W 00h Reserved

2Fh R/W 00h Reserved

S: Strapping; x: chip version.

7. HARDWARE MONITOR

7.1 General Description

The W83627EHF/EHG can be used to monitor several critical hardware parameters of the system,

including power supply voltages, fan speeds, and temperatures, which are very important for a

high-end computer system to work stable and properly. W83627EHF/EHG provides LPC interface to

access hardware.

An 8-bit analog-to-digital converter (ADC) was built inside W83627EHF/EHG. The W83627EHF/EHG

can simultaneously monitor 6 analog voltage inputs (intrinsic monitor VBAT, 3VSB, 3VCC,& AVCC

power), 5 fan tachometer inputs, 3 remote temperature, one case-open detection signal. The remote

temperature sensing can be performed by thermistors or directly from IntelTM Deschutes CPU thermal

diode output. Also the W83627EHF/EHG provides: 4 PWM (pulse width modulation) outputs for the

fan speed control or 4 DCFAN outputs for the fan speed control; beep tone output for warning;

SMI#(through SERIRQ or OVT# pin) , OVT# signals for system protection events.

Through the application software or BIOS, the users can read all the monitored parameters of system

from time to time. And a pop-up warning can be also activated when the monitored item was out of

the proper/preset range. The application software could be Nuvoton's Hardware DoctorTM or other

management application software. Also the users can set up the upper and lower limits (alarm

thresholds) of these monitored parameters and to activate one programmable and masked interrupts.

- 34 -

W83627EHF/EF

W83627EHG/EG

An optional beep tone could be used as warning signals when the monitored parameters are out of the

preset range.

7.2 Access Interface

W83627EHF/EHG provides two interface for microprocessor to read/write hardware monitor internal

registers.

7.2.1 LPC interface

The first interface uses LPC Bus to access which the ports of low byte (bit2~bit0) are defined in the port

5h and 6h. The other higher bits of these ports are set by W83627EHF/EHG itself. The general

decoded address is set to port 295h and port 296h. These two ports are described as following:

Port 295h: Index port.

Port 296h: Data port.

The register structure is showed as the Figure 7.1

Publication Release Date: April 7 , 2009

-35- Version 1.94

W83627EHF/EF

W83627EHG

Configuration Register

40h

Interrupt Status Registers

41h, 42h

SMI# Mask Registers

43h-44h

Fan Divisor Register I

47h

Monitor Value Registers

20h~3Fh

4Bh

HM_SMI#/OVT# Control Register

4Ch

Fan IN /OUT Control Register

4Dh

Bank Select for 50h~5Fh

Registers.

4Eh

Winbond Vendor ID

4Fh

BANK 0

BEEP Control Registers

56h~57h

BANK 0

Chip ID Register

58h

BANK 0

Temperature Sensor Type

Configuration &

Fan Divisor Bit2 Registers

59h,5Dh

Data

Port 6h

Port 5h

Index

LPC

Bus

Smart Fan Configuration

Registers

00h-1Fh

BANK 4

Interrupt Status & HM_SMI

Mask Registers

50h~51h

BANK 4

Beep Control Registers

53h

BANK 4

Temperature Offset

Registers

54h~56h

BANK 4

Read Time Status

Registers

59h~5Bh

BANK 5

59h~5Bh

Monitor Value Registers

Fan Divisor Register I

BANK 1

CPUTIN Temperature

Control/Staus Registers

50h~56h

BANK 2

AUXTIN Temperature

Control/Staus Registers

50h~56h

Serial Bus Address

48h

FAN4 Source Select Register

4Ah

Figure 7.1 : LPC interface access diagram

7.2.2 I2C interface

The second interface uses I2C Serial Bus. W83627EHF/EHG has a programmable serial bus address.

It defined at Index 48h.

- 36 -

W83627EHF/EF

W83627EHG/EG

7.2.2.1. Serial bus (I2C) access timing

(a) Serial bus write to internal address register followed by the data byte

Start By

Master

0101101 D7 D6 D5 D4 D3 D2 D1 D0

Ack

627EHF

R/W

Ack

627EHF

SCL

SDA

D7 D6 D5 D4 D3 D2 D1 D0

Ack

784R

Stop

Master

SCL

SDA (Continued)

780 78

Frame 2

Internal Index Register Byte

(Continued)

Frame 3

Data Byte

Frame 1

Serial Bus Address Byte

Ack

627EHF

(b) Serial bus read from a register

D7 D6 D5 D4 D3 D2 D1 D0

Ack

Master

Ack

627EHF

780 78

Frame 4

Data Byte

Frame 3

Serial Bus Address Byte

Stop by

Master

Start By

Master

0101101 D7 D6 D5 D4 D3 D2 D1 D0R/W

Ack

627EHF

SCL

SDA

780 78

Frame 2

Internal Index Register Byte

Frame 1

Serial Bus Address Byte

Ack

627EHF

0101101R/W

Repeat

start

Master

7.3 Analog Inputs

The maximum input voltage of the analog pin is 2.048V because the 8-bit ADC has a 8mV LSB. Really,

the application of the PC monitoring would most often be connected to power suppliers. The CPU

Vcore voltage, VBAT(pin 74), 3VSB(pin 61), 3VCC(pin 12) , AVCC(pin 114) voltage can directly

connected to these analog inputs. The +12V voltage inputs should be reduced a factor with external

resistors so as to obtain the input range. As Figure 7.2 shows.

Publication Release Date: April 7 , 2009

-37- Version 1.94

W83627EHF/EF

W83627EHG

Pin 97

VIN2

CPUVCORE Pin 64

Pin 99

VIN0

VIN1

VBAT

Pin 98

Pin 74

Positive Voltage Input

Negative Voltage Input

8-bit ADC

with

8mV LSB

10K, 1%

RTHM

VREF Pin 101

AUXTIN

CPUTIN

SYSTIN

Pin 102

Pin 103

Pin 104

VSB Pin 61

10K@25 C, beta=3435K

AVCC Pin 114

Power Inputs

15K, 1%

CAP,2200p

CPUD+

CPUD-

Pin 12

3VCC

Pin 96

VIN3

Pin 95

VIN4

AGND Pin 117

Figure 7.2

7.3.1 Monitor over 2.048V voltage

The +12V input voltage can be expressed as following equation.

0RR R

VVIN +

×=

The value of R1 and R2 can be selected to 56K Ohms and 10K Ohms, respectively, when the input

voltage V0 is 12V. The node voltage of VIN0 can be subject to less than 2.048V for the maximum input

range of the 8-bit ADC.

The -12V input voltage can be expressed as following equation.

12,048.2)048.2(1 1

1−=+

×−= whereV

VVIN

The value of R3 and R4 can be selected to 232K Ohms and 10K Ohms, respectively, when the input

voltage V1 is -12V. The node voltage of VIN1 can be subject to less than 2.048V for the maximum input

range of the 8-bit ADC.

- 38 -

W83627EHF/EF

W83627EHG/EG

Both of pin 12 and pin 114 are connected to the power supply VCC with +3.3V. There are two functions

in these 2 pins with 3.3V. The first function is to supply internal (digital/analog) power in the

W83627EHF/EHG and the second function is that this voltage with 3.3V is connected to internal serial

resistors to monitor the +3.3V voltage. The W83627EHF/EHG internal two serial resistors are 34 KΩ

and 34 KΩ so that input voltage to ADC is 1.65V which is less than 2.048V of ADC maximum input

voltage. The express equation can represent as follows.

KK K

VCCVin 65.1

3434 34 ≅

Ω+Ω

×= , where VCC is set to 3.3V.

The Pin 61 is connected to 3.3 VSB voltage. W83627EHF/EHG monitors this voltage and the internal

two serial resistors are 34 KΩ and 34 KΩ so that input voltage to ADC is 1.65V which less than 2.048V

of ADC maximum input voltage.

7.3.2 CPUVCORE voltage detection method

W83627EHF/EHG provides one detection methods for CPUVCORE(pin 100).

The LSB of this mode is 8mV. This means that the detected voltage equals to the reading of this

voltage register multiplies 8mV. The formula is as the following:

Detected Voltage = 008.0Reading

∗

7.3.3 Temperature Measurement Machine

The temperature data format is 8-bit two's-complement for sensor SYSTIN and 9-bit two's-complement

for sensor CPUTIN and AUXTIN. The 8-bit temperature data can be obtained by reading the Index[27h].

The 9-bit temperature data can be obtained by reading the 8 MSBs from the Bank1/Bank2 Index[50h]

and the LSB from the Bank1/Bank2 Index[51h] bit 7. The format of the temperature data is show in

Table 7.1.

TEMPERATURE 8-BIT DIGITAL OUTPUT 9-BIT DIGITAL OUTPUT

8-BIT BINARY 8-BIT HEX 9-BIT BINARY 9-BIT HEX

+125°C 0111,1101 7Dh 0,1111,1010 0FAh

+25°C 0001,1001 19h 0,0011,0010 032h

+1°C 0000,0001 01h 0,0000,0010 002h

+0.5°C - - 0,0000,0001 001h

+0°C 0000,0000 00h 0,0000,0000 000h

Publication Release Date: April 7 , 2009

-39- Version 1.94

W83627EHF/EF

W83627EHG

TEMPERATURE 8-BIT DIGITAL OUTPUT 9-BIT DIGITAL OUTPUT

8-BIT BINARY 8-BIT HEX 9-BIT BINARY 9-BIT HEX

-0.5°C - - 1,1111,1111 1FFh

-1°C 1111,1111 FFh 1,1111,1110 1FFh

-25°C 1110,0111 E7h 1,1100,1110 1CEh

-55°C 1100,1001 C9h 1,1001,0010 192h

Table 7.1

7.3.3.1. Monitor temperature from thermistor

The W83627EHF/EHG can connect three thermistors to measure three different environment

temperature. The specification of thermistor should be considered to (1) β value is 3435K, (2) resistor

value is 10K ohms at 25°C. In the Figure 7.2, the themistor is connected by a serial resistor with 10K

Ohms, then connect to VREF (pin 101).

7.3.3.2. Monitor temperature from Pentium IITM/Pentium IIITM thermal diode

The W83627EHF/EHG can alternate the thermistor to Pentium IITM/Pentium IIITM thermal diode and the

circuit connection is shown as Figure 7.3. The pin of Pentium IITM/ Pentium IIITM D- is connected to

AGND(pin 117) and the pin D+ is connected to temperature sensor pin in the W83627EHF/EHG. The

resistor R=15K ohms should be connected to VREF to supply the diode bias current and the bypass

capacitor C=2200pF should be added to filter the high frequency noise.

Pentium II/III/IV

CPU D+

D-

Therminal

Diode C=2200pF

R=15K,1%

VREF

CPUTIN

W83627EHF

AGND

Figure 7.3

- 40 -

W83627EHF/EF

W83627EHG/EG

7.4 FAN Speed Count and FAN Speed Control

7.4.1 Fan speed count

Inputs are provides for signals from fans equipped with tachometer outputs. The level of these signals

should be set to TTL level, and maximum input voltage can not be over +3.3V. If the input signals from

the tachometer outputs are over the +3.3V, the external trimming circuit should be added to reduce the

voltage to obtain the input specification. The normal circuit and trimming circuits are shown as Figure

7.4.

Determine the fan counter according to:

DivisorRPM

Count ×

1035.1

In other words, the fan speed counter has been read from register Bank0 Index 28h, 29h, 2Ah, 3Fh and

Bank5 53h, the fan speed can be evaluated by the following equation.

RPM Count Divisor

=×

135 106

The default divisor is 2 and defined at Bank0 Index 47h.bit7~4, Index 4Bh.bit7~6, Index 4Ch.bit7, Index

59h.bit7.bit3~2 and Index 5Dh.bit5~7 which are three bits for divisor. That provides very low speed fan

counter such as power supply fan. The followed table is an example for the relation of divisor, RPM,

and count.

Divisor Nominal

RPM

Time per

Revolution

Counts 70% RPM Time for 70%

1 8800 6.82 ms

153 6160 9.84 ms

2 (default) 4400 13.64 ms 153 3080 19.48 ms

4 2200 27.27 ms

153 1540 38.96 ms

8 1100 54.54 ms

153 770 77.92 ms

16 550 109.08 ms

153 385 155.84 ms

32 275 218.16 ms

153 192 311.68 ms

64 137 436.32 ms

153 96 623.36 ms

Publication Release Date: April 7 , 2009

-41- Version 1.94

W83627EHF/EF

W83627EHG

Divisor Nominal

RPM

Time per

Revolution

Counts 70% RPM Time for 70%

128 68 872.64 ms

153 48 1246.72 ms

Table 7.2

7.4.2 Fan speed control

W83627EHF/EHG provides two controllable methods for Fan speed control. One is PWM duty cycle

output and the other is DC voltage output. Either PWM or DC output can be programmed at Bank0

Index 04h.bit1~0, Index 12h.bit0 and Index 62h.bit6.

7.4.2.1. PWM Duty Cycle Output

The W83627EHF/EHG provides maximum 4 sets for fan PWM speed control. The duty cycle of PWM

can be programmed by a 8-bit registers which are defined in the Bank0 Index 01h, Index 03h, Index

11h and Index 61h. The default duty cycle is set to 100%, that is, the default 8-bit registers is set to FFh.

The expression of duty can be represented as follows.

%100

255 ValueRegister bit -8 Programmed

(%)Dutycycle ×=

The PWM clock frequency also can be program and defined in the Bank0 Index 00h, Index 02h, Index

10h and Index 60h.

7.4.2.2. DC Voltage Output

The W83627EHF/EHG has a 6 bit DAC which produces 0 to 3.3 volts DC output that provides

maximum 4 sets for fan speed control. The analog output can be programmed in the Bank0 Index 01h,

Index 03h, Index 11h and Index 61h. The default value is 111111YY,YY is reserved 2 bits, that is

default output value is nearly 3.3 V. The expression of output voltage can be represented as follow ,

ValueRegister bit-6 Programmed

3)( ×= VCCVageOutputVolt

7.5 Conversion Sequence and Conversion Time

The conversion sequence and conversion time of the W83627EHF/EHG include the voltage and

temperature conversion time. The sample rate of the W83627EHF/EHG is 22.5 KHz. 24 cycles are

needed to complete the ADC conversion of the temperature (worst case), and 16 cycles are needed for

the ADC conversion of the voltage. The W83627EHF/EHG has 10 voltage sets and 3 temperature sets.

- 42 -

W83627EHF/EF

W83627EHG/EG

The monitor time of the 3 temperature sets: 3* 24 * 0.044mS = 3.168 ms

The 10 voltage sets: 10 * 16 * 0.044 ms = 7.04 ms

Total conversion time = 3.168 + 7.04 = 10.208 ms

Please note that the suggested time interval for the most updated data is 20 ms.

Publication Release Date: April 7 , 2009

-43- Version 1.94

W83627EHF/EF

W83627EHG

7.6 Smart Fan Control

SMART FANTM I：

Smart Fan Control provides two mechanisms. One is Thermal Cruise mode and the other is Fan Speed

Cruise mode. When enable Smart Fan, the Fan output will start from previous setting of Bank0 Index

01h, Index 03h, Index 11h and Index 61h to increase or decrease.

Pin 103 CPUTIN Pin 115 CPUFANOUT0

Pin 104 SYSTIN

Pin 116 SYSFANOUT

Pin 7 AUXFANOUT

Pin 120 CPUFANOUT1

Pin 102 AUXTIN

7.6.1 Thermal Cruise mode

There are maximum 4 pairs of Temperature/Fan output control at this mode: SYSTIN with

SYSFANOUT, CPUTIN with CPUFANOUT0, AUXTIN with AUXFANOUT and CPUFANOUT1 depends

on Bank0 Index 4Ah.bit7~6 setting that is temperature source selection.

W83627EHF/EHG provides the Smart Fan system which can control the fan speed automatically

depend on current temperature to keep it with in a specific range. At first a wanted temperature and

interval must be set (ex. 55 °C ± 3 °C) by BIOS, as long as the real temperature remains below the

setting value, the fan will be off. Once the temperature exceeds the setting high limit temperature

( 58°C), the fan will be turned on with a specific speed set by BIOS (ex: 20% output) and automatically

controlled its output with the temperature varying. Three conditions may occur :

- 44 -

W83627EHF/EF

W83627EHG/EG

(1) If the temperature still exceeds the high limit (ex: 58°C), Fan output will increase slowly. If the fan

has been operating in its fully speed but the temperature still exceeds the high limit(ex: 58°C), a

warning message will be issued to protect the system.

(2) If the temperature goes below the high limit (ex: 58°C), but above the low limit (ex: 52°C), the fan

speed will be fixed at the current speed because the temperature is in the target area(ex: 52 °C ~

58°C).

(3) If the temperature goes below the low limit (ex: 52°C), Fan output will decrease slowly to 0 until the

temperature exceeds the low limit.

In other words, If “current temperature” > “High Limit”, increase fan speed;

If “current temperature” < “Low Limit”, decrease fan speed;

Otherwise, keep the fan speed.

Figure 7.6 PWM fan mode and Figure 7.7 DC fan mode illustrate the Thermal Cruise mode

Figure 7.6

Publication Release Date: April 7 , 2009

-45- Version 1.94

W83627EHF/EF

W83627EHG

Figure 7.7

in order to keep the fans running with a minimum speed. By setting Bank0 Index12h.bit3~5 to 1,

Fan output will be decreased to the “Stop Output Value” which are defined at Bank0 Index08h,

Index09h and Index17h.

(d)

7.6.2 Fan Speed Cruise mode

There are 4 pairs of Fan input/Fan output control at this mode: SYSFANIN with SYSFANOUT,

CPUFANIN0 with CPUFANOUT0, AUXFANIN with AUXFANOUT and CPUFANIN1 with

CPUFANOUT1. At this mode, W83627EHF/EHG provides the Smart Fan system which can control the

fan speed automatically depend on current fan speed to keep it with in a specific range. A wanted fan

speed count and interval must be set (ex. 160 ± 10 ) by BIOS. As long as the fan speed count is the

specific range, Fan output will keep the current value. If current fan speed count is higher than the high

limit (ex. 160+10), Fan output will be increased to keep the count less than the high limit. Otherwise, if

current fan speed is less than the low limit(ex. 160-10), Fan output will be decreased to keep the count

higher than the low limit. See Figure 7.8 example.

- 46 -

W83627EHF/EF

W83627EHG/EG

160

170

150

Fan

output

100

Count

(%)

Figure 7.8

7.6.3 Manual Control Mode

Smart Fan control system can be disabled and the fan speed control algorithm can be programmed by

BIOS or application software. The programming method must be set fan configuration at bank 0 index

04h,bit5-4 to 1,index 62h bit5~4 to 1. Then table 7.3-1 displayed current temperature and fan output

value at Smart Fan I Mode Besides, these tables 7.3-2 and 7.3-3 used to setting thermal mode or

speed cruise mode of Smart Fan I mode.

Table 7.3-1 Display Register- at Smart Fan I Mode

DESCRIPTION REGISTER

ADDRESS REGISTER NAME ATTRIBUTE BIT DATA

Current CPU

Temperature

Bank1

50H ,51H

CPUTIN Temperature

Sensor

Read only 8 MSB, 1°C bit 7,

0.5 °C

Current SYS

Temperature

Bank 0

27H

SYSTIN Temperature

Sensor

Read only 8 MSB, 1°C

Current AUX

Temperature

Bank2

50h,51h

AUXTIN Temperature

Sensor

Read only 8 MSB, 1°C bit 7,

0.5 °C

Current

CPUFANOUT0

Output Value

Bank0

03h

CPUFANOUT0 Output

Value Select

FFh Bit7-0

CPUFANOUT

Value

Current

SYSFANOUT

Bank0

01h

SYSFANOUT Output

Value Select

FFh Bit7-0

SYSFANOUT

Publication Release Date: April 7 , 2009

-47- Version 1.94

W83627EHF/EF

W83627EHG

DESCRIPTION REGISTER

ADDRESS REGISTER NAME ATTRIBUTE BIT DATA

Output Value Value

Current

AUXFANOUT

Output Value

Bank0

11h

AUXFANOUT1 Output

Value Select

FFh Bit7-0

AUXFANOUT

Value

Current

CPUFANOUT1

Output Value

Bank0

61h

CPUFANOUT1 Output

Value Select

FFh Bit7-0

CPUFANOUT1

Value

Table 7.3-2 Relative Register-at Thermal Cruise Mode of Smart Fan I control mode

THERMAL-

CRUISE MODE

TARGET

TEMPERATURE

TOLERANCE START-

VALUE

STOP

VALUE

KEEP

MIN.

FAN

OUTPUT

VALUE

STOP

TIME

STEP-

DOWN

TIME

STEP-

TIME

SYSFANOUT CR[05h] CR[07h]

Bit0-3

CR[0Ah] CR[08]h CR[12h]

Bit5

CR[0Ch]

CPUFANOUT0 CR[06h] CR[07h]

Bit4-7

CR[0Bh] CR[09h] CR[12h]

Bit4

CR[0Dh]

AUXFANOUT CR[13h] CR[14h]

Bit0-3

CR[16h] CR[15h] CR[12h]

Bit3

CR[17h]

CPUFANOUT1 CR[63h] CR[62h]

Bit0-3

CR[65h] CR[64h] CR[12h]

Bit6

CR[66h]

CR[0Eh] CR[0Fh]

Table 7.3-3 Relative Register-at Speed Cruise Mode of Smart Fan I control mode

THERMAL-CRUISE

MODE

TARGET-SPEED

COUNT

TOLERANCE KEEP MIN.

FAN

OUTPUT

VALUE

STEP-DOWN

TIME

STEP-UP

TIME

- 48 -

W83627EHF/EF

W83627EHG/EG

SYSFANOUT CR[05h] CR[07h]

Bit0-3

CR[12h]

Bit5

CPUFANOUT0 CR[06h] CR[07h]

Bit4-7

CR[12h]

Bir4

AUXFANOUT CR[13h] CR[14h]

Bit0-3

CR[12h]

Bit3

CPUFANOUT1 CR[63h] CR[62h]

Bit0-3

CR[12h]

Bit6

CR[0Eh] CR[0Fh]

SMART FANTM III

Concept

SMART FANTM III mode sets a target temperature through BIOS or application software and

W83627EHF/EHG controls the fan speed so that the temperature could meet the target temperature

set in the BIOS or software. Only Pin115 (CPUFANOUT0) and Pin120 (CPUFANOUT1) in

W83627EHF/EHG support SMART FANTM III. Pin115 (CPUFANOUT0) pairs with Pin103 (CPUTIN);

while Pin120 (CPUFANOUT1) pairs with Pin104 (SYSTIN), Pin103 (CPUTIN), or Pin102 (AUXTIN),

which is defined in Bank0 Index 4Ah.bit7~6.

Pin 103 CPUTIN

Pin 115 CPUFANOUT0

Pin 104 SYSTIN

Pin 102 AUXTIN

Pin 120 CPUFANOUT1

Figure 7.9, 7.10, and 7.11 illustrate SMART FANTM III mode, and the algorithm of fan speed control is

described as follows:

Publication Release Date: April 7 , 2009

-49- Version 1.94

W83627EHF/EF

W83627EHG

(1) Figure 7.9 shows the initial condition of SMART FANTM III. Target Temperature, Temperature

Tolerance, Maximum Fan Output and Minimum Fan Output must be set first. If the currently

measured temperature is within the (Target Temperature ± Temperature Tolerance), the fan speed

remains constant.

(2) In the case that currently measured temperature goes beyond (Target Temperature ＋

Temperature Tolerance), which is shown in Figure 7.10, fan speed jumps up to the next step.

“Step” here refers to the value in the CPUFANOUT Output Value Select Register, Bank0 Index03h

or Index61h.

(3) Meanwhile, original Target Temperature dynamically shifts to (Target Temperature ＋

Temperature Tolerance), and new Target Temperature, named Target Temperature 1, is formed.

In other words, Target Temperature 1 equals original Target Temperature plus Temperature

Tolerance.

(4) If the currently measured temperature is within the (Target Temperature 1 ± Temperature

Tolerance) then, the fan speed remains constant. Otherwise, fan speed jumps up to the next step

again. Target Temperature then dynamically shifts to (Target Temperature 1 ＋ Temperature

Tolerance), and new Target Temperature again, named Target Temperature 2, is formed.

(5) The fan-speed-up and Target Temperature comparison-then-shift process continue until currently

measured temperature locates within (Target Temperature X ± Temperature Tolerance), or fan

output speed reaches its maximum speed.

(6) Please be noted that “Speed-up Slope” shown in the Figure 7.10 must be an integer. In other words,

Steps putInitialOutFanOutputMax −. must be an integer; otherwise, it may lead to register overflow.

(7) In the case that currently measured temperature goes below (Target Temperature －

Temperature Tolerance), which is shown in Figure 7.11, fan speed slows down by one step. “Step”

here refers to the value in the CPUFANOUT Output Value Select Register, Bank0 Index03h or

Index61h.

(8) Meanwhile, original Target Temperature dynamically shifts to (Target Temperature －

Temperature Tolerance), and new Target Temperature, named Target Temperature 1, is formed.

In other words, Target Temperature 1 equals original Target Temperature minus Temperature

Tolerance.

(9) If the currently measured temperature is within the (Target Temperature 1 ± Temperature

Tolerance) then, the fan speed remains constant. Otherwise, fan speed slows down by one step

again. Target Temperature then dynamically shifts to (Target Temperature 1 － Temperature

Tolerance), and new Target Temperature again, named Target Temperature 2, is formed.

- 50 -

W83627EHF/EF

W83627EHG/EG

(10) The fan-slow-down and Target Temperature comparison-then-shift process continue until

currently measured temperature locates within (Target Temperature X ± Temperature Tolerance),

or fan output speed hits its minimum speed.

(11) Please be noted that “Speed-down Slope” shown in the Figure 7.11 must be an integer. In other

words, Step FanOutputMinputInitialOut .− must be an integer; otherwise, it may lead to register overflow.

(12) In the case that the temperature is always lower than (Target Temperature X － Temperature

Tolerance), and, for some reason, the fan speed would like to be kept at the minimum speed, Stop

Value, instead of being stopped, set register Bank0 12h.bit 4. Set bit 4 to 1, fan speed will always

keep at the value set in Bank0 Index09h when temperature is always below (Target Temperature X

－ Temperature Tolerance). Set bit 4 to 0, fan speed will decrease to 0 after a time period set in

Bank0 Index 0Dh.

Temperature

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Setting

Tolerance

Tar. + Tol.

Tar. - Tol.

Temperature

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Setting

Tolerance

Tar. + Tol.

Tar. - Tol.

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Setting

Tolerance

Tar. + Tol.

Tar. - Tol.

Figure 7.9

Publication Release Date: April 7 , 2009

-51- Version 1.94

W83627EHF/EF

W83627EHG

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Temperature

Tolerance

Tar

Current Temp. > Target Temp. + Tol.

Tar 1

Tar 2

Tar 3

Tar 4

Tar 5

Step

Speed-up Slope

Fan Initial

Output Value

(Max. Fan output –Initial output)

Step

= Integer

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Temperature

Tolerance

Tar

Current Temp. > Target Temp. + Tol.

Tar 1

Tar 2

Tar 3

Tar 4

Tar 5

Step

Speed-up Slope

Fan Initial

Output Value

(Max. Fan output –Initial output)

Step

= Integer

Figure 7.10

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Temperature

Tolerance

Tar

Current Temp. < Target Temp. - Tol.

Tar 1

Tar 2

Tar 3

Speed-down Slope

Step

Fan Initial

Output Value

(Initial Value –Min. Fan output)

Step

= Integer

Min. Fan Output

Max. Fan Output

Fan output

(DC / PWM)

Temperature

Tolerance

Tar

Current Temp. < Target Temp. - Tol.

Tar 1

Tar 2

Tar 3

Speed-down Slope

Step

Fan Initial

Output Value

(Initial Value –Min. Fan output)

Step

= Integer

Figure 7.11

7.6.4 Smart FanTM III Mode

- 52 -

W83627EHF/EF

W83627EHG/EG

Smart FanTM III control system can be disabled and the fan speed control algorithm can be

programmed by BIOS or application software. The programming method must be set fan configuration

at bank 0 index 04h,bit5-4,index 12h bit2~1 index 62h bit5~4.Before enabling Smart FanTM III

mode ,you have to set relative registers as table 7.4-2. In addition to the required registers, the device

has a the following registers that further configure and enable the fan speed control functionality .Then

Table 7.4-1 displayed current temperature and fan output value at Smart FanTM III mode , Besides,

the table 7.4-2 used to setting at Smart FanTM III mode

Table 7.4-1 Display Register- at Smart FanTM III Mode

DESCRIPTION REGISTER

ADDRESS REGISTER NAME ATTRIBUTE BIT DATA

Current CPU

Temperature

Bank1

50h ,51h

CPUTIN Temperature

Sensor

Read only 8 MSB, 1°C bit 7,

0.5 °C

Current SYS

Temperature

Bank 0

27h

SYSTIN Temperature

Sensor

Read only 8 MSB, 1°C

Current AUX

Temperature

Bank2

50h,51h

AUXTIN Temperature

Sensor

Read only 8 MSB, 1°C bit 7,

0.5 °C

Current

CPUFANOUT0

Output Value

Bank0

03h

CPUFANOUT0 Output

Value Select

FFh Bit7-0

CPUFANOUT

Value

Current

SYSFANOUT

Output Value

Bank0

01h

SYSFANOUT Output

Value Select

FFh Bit7-0

SYSFANOUT

Value

Table 7.4-2 Relative Register-at Smar t FanTM III control mode

Smart FanTM III

Mode

Target

Temperature

Tolerance Stop Value

(Min. Fan

Output)

Max. Fan

Output

Stop Time

CPUFANOUT0 CR[06h] CR[07h] bit 4-7 CR[09h] CR[67h] CR[0Dh]

CPUFANOUT1 CR[63h] CR[62h] bit 0-3 CR[64h] CR[69h] CR[66h]

Publication Release Date: April 7 , 2009

-53- Version 1.94

W83627EHF/EF

W83627EHG

Smart FanTM III

Mode

Output Step Step Down

Time

Step Up

Time

Keep Min. Fan

Output value

CPUFANOUT0 CR[68h] CR[0Eh] CR[0Fh] CR[12h] bit 4

CPUFANOUT1 CR[6Ah] CR[0Eh] CR[0Fh] CR[12h] bit 6

- 54 -

W83627EHF/EF

W83627EHG/EG

7.7 SMI# interrupt mode

The SMI#/OVT# pin is a multi-function pin. The function is selected at Configuration Register CR[29h]

bit 6.

7.7.1 Voltage SMI# mode

SMI# interrupt for voltage is Two-Times Interrupt Mode. Voltage exceeding high limit or going below

low limit will causes an interrupt if the previous interrupt has been reset by reading all the interrupt

Status Register. (Figure 7.12)

7.7.2 Fan SMI# mode

SMI# interrupt for fan is Two-Times Interrupt Mode. Fan count exceeding the limit, or exceeding and

then going below the limit, will causes an interrupt if the previous interrupt has been reset by reading all

the interrupt Status Register. (Figure 7.13)

***

*Interrupt Reset when Interrupt Status Registers are read

SMI# *

High limit

Low limit

SMI# *

Fan Count limit

Figure 7.12 Figure 7.13

Publication Release Date: April 7 , 2009

-55- Version 1.94

W83627EHF/EF

W83627EHG

7.7.3 Temperature SMI# mode

7.7.3.1. Temperature sensor 1(SYSTIN) SMI# interrupt has 3 modes

(1) Comparator Interrupt Mode

Setting the THYST (Temperature Hysteresis) limit to 127°C will set temperature sensor 1 SMI# to the

Comparator Interrupt Mode. Temperature exceeds TO (Over Temperature) Limit causes an

interrupt and this interrupt will be reset by reading all the Interrupt Status Register. Once an

interrupt event has occurred by exceeding TO, then reset, if the temperature remains above the

TO , the interrupt will occur again when the next conversion has completed. If an interrupt event

has occurred by exceeding TO and not reset, the interrupts will not occur again. The interrupts will

continue to occur in this manner until the temperature goes below TO. (Figure 7.14)

Setting the THYST lower than TO will set temperature sensor 1 SMI# to the Interrupt Mode. The

following are two kinds of interrupt modes, which are selected by Bank0 Index 4Ch bit5:

(2) Two-Times Interrupt Mode

Temperature exceeding TO causes an interrupt and then temperature going below THYST will also

cause an interrupt if the previous interrupt has been reset by reading all the interrupt Status

remains above the THYST, the interrupt will not occur. (Figure 7.15)

(3) One-Time Interrupt Mode

Temperature exceeding TO causes an interrupt and then temperature going below THYST will not

cause an interrupt. Once an interrupt event has occurred by exceeding TO, then going below THYST,

an interrupt will not occur again until the temperature exceeding TO. (Figure 7.16)

- 56 -

W83627EHF/EF

W83627EHG/EG

HYST

*Interrupt Reset when Interrupt Status Registers are read

HYST

SMI# SMI#

** * **

127'C

Figure 7.14 Figure 7.15

*Interrupt Reset when Interrupt Status Registers are read

HYST

SMI# * *

Figure 7.16

Publication Release Date: April 7 , 2009

-57- Version 1.94

W83627EHF/EF

W83627EHG

7.7.3.2. Temperature sensor 2(CPUTIN) and sensor 3(AUXTIN) SMI# interrupt has two modes

It is programmed at Bank0 Index 4Ch.bit 6.

(1) Comparator Interrupt Mode

Temperature exceeding TO causes an interrupt and this interrupt will be reset by reading all the

Interrupt Status Register. Once an interrupt event has occurred by exceeding TO, then reset, if the

temperature remains above the THYST, the interrupt will occur again when the next conversion has

completed. If an interrupt event has occurred by exceeding TO and not reset, the interrupts will

not occur again. The interrupts will continue to occur in this manner until the temperature goes

below THYST. (Figure 7.17)

(2) Two-Times Interrupt Mode

Temperature exceeding TO causes an interrupt and then temperature going below THYST will also

cause an interrupt if the previous interrupt has been reset by reading all the interrupt Status

remains above the THYST, the interrupt will not occur. (Figure 7.18)

HYST

***

*Interrupt Reset when Interrupt Status Registers are read

HYST

SMI# SMI#

** * **

Figure 7.17 Figure 7.18

- 58 -

W83627EHF/EF

W83627EHG/EG

7.8 OVT# interrupt mode

The SMI#/OVT# pin (pin 5) is a multi-function pin. The function is selected at Configuration

52h bit1 and Bank2 Index 52h bit1.

(1) Comparator Mode:

Temperature exceeding TO causes the OVT# output activated until the temperature is less than

THYST. (Figure 7.19)

(2) Interrupt Mode:

Temperature exceeding TO causes the OVT# output activated indefinitely until reset by reading

temperature sensor registers. Temperature exceeding TO, then OVT# reset, and then temperature

going below THYST will also cause the OVT# activated indefinitely until reset by reading

temperature sensor registers. Once the OVT# is activated by exceeding TO, then reset, if the

temperature remains above THYST, the OVT# will not be activated again.(Figure 7.19)

HYST

*Interrupt Reset when Temperature sensor registers are read

OVT#

(Comparator Mode; default)

(Interrupt Mode)

Figure 7.19

Publication Release Date: April 7 , 2009

-59- Version 1.94

W83627EHF/EF

W83627EHG

7.9 Registers and RAM

Address Port and Data Port are set in the register CR60 and CR61 of Device B which is Hardware

Monitor Device. The value in CR60 is high byte and that in CR61 is low byte. For example, setting

CR60 to 02 and CR61 to 90 causes the Address Port to be 0x295 and Data Port to be 0x296.

7.9.1 Address Port (Port x5h)

Address Port: Port x5h

Power on Default Value 00h

Attribute: Bit 6:0 Read/write , Bit 7: Reserved

Size: 8 bits

7 6 5 4 3 2 1 0

Data

Bit7: Reserved

Bit 6-0: Read/Write

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Reserved Address Pointer (Power On default 00h)

(Power On default 0) A6 A5 A4 A3 A2 A1 A0

7.9.2 Data Port (Port x6h)

Data Port: Port x6h

Power on Default Value 00h

Attribute: Read/write

Size: 8 bits

- 60 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

Data

Bit 7-0: Data to be read from or to be written to RAM and Register.

7.9.3 SYSFANOUT PWM Output Frequency Configuration Register - Index 00h (Bank 0)

Power on Default Value: 04h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

PWM_CLK_SEL1

PWM_SCALE1

The register is meaningful when SYSFANOUT be programmed as PWM output.

Bit 7: SYSFANOUT PWM Input Clock Source Select. This bit selects the clock source of PWM

output frequency.

Set to 0, select 24 MHz.

Set to 1, select 180 KHz.

Bit 6-0: SYSFANOUT PWM Pre-Scale divider. This is the divider of clock source of PWM output

frequency. The maximum divider is 128 (7Fh). This divider should not be set to 0.

01h : divider is 1

02h : divider is 2

03h : divider is 3

Publication Release Date: April 7 , 2009

-61- Version 1.94

W83627EHF/EF

W83627EHG

the formula is PWM output frequency = 256

Divider Pre_Scale

ClockInput ∗

7.9.4 SYSFANOUT Output Value Select Register - Index 01h (Bank 0)

Power on Default Value: FFh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

SYSFANOUT Value

(1)If SYSFANOUT be programmed as PWM output (Bank0 Index 04h.bit0 is 0)

Bit 7-0: SYSFANOUT PWM Duty Cycle. Write FFh, SYSFANOUT is always logical High which means

duty cycle is 100%. Write 00h, SYSFANOUT is always logical Low which means duty cycle is

0%.

Note. XXh: PWM Duty Cycle output percentage is (XX/256*100%) during one cycle.

(2)If SYSFANOUT be programmed as DC Voltage output (Bank0 Index 04h.bit0 is 1)

Bit 7-2: SYSFANOUT voltage control.

Bit 1-0: Reserved.

OUTPUT Voltage = 64

*FANOUT

AVCC

If AVCC= 3.3V , output voltage table is

BIT

OUTPUT

VOLTAGE

BIT

OUTPUT

VOLTAGE

0 0 0 0 0 0 0 1 0 0 0 0 0 1.65

0 0 0 0 0 1 0.05 1 0 0 0 0 1 1.70

- 62 -

W83627EHF/EF

W83627EHG/EG

BIT

OUTPUT

VOLTAGE

BIT

OUTPUT

VOLTAGE

0 0 0 0 1 0 0.10 1 0 0 0 1 0 1.75

0 0 0 0 1 1 0.15 1 0 0 0 1 1 1.80

0 0 0 1 0 0 0.21 1 0 0 1 0 0 1.86

0 0 0 1 0 1 0.26 1 0 0 1 0 1 1.91

0 0 0 1 1 0 0.31 1 0 0 1 1 0 1.96

0 0 0 1 1 1 0.36 1 0 0 1 1 1 2.01

0 0 1 0 0 0 0.41 1 0 1 0 0 0 2.06

0 0 1 0 0 1 0.46 1 0 1 0 0 1 2.11

0 0 1 0 1 0 0.52 1 0 1 0 1 0 2.17

0 0 1 0 1 1 0.57 1 0 1 0 1 1 2.22

0 0 1 1 0 0 0.62 1 0 1 1 0 0 2.27

0 0 1 1 0 1 0.67 1 0 1 1 0 1 2.32

0 0 1 1 1 0 0.72 1 0 1 1 1 0 2.37

0 0 1 1 1 1 0.77 1 0 1 1 1 1 2.42

0 1 0 0 0 0 0.83 1 1 0 0 0 0 2.48

0 1 0 0 0 1 0.88 1 1 0 0 0 1 2.53

0 1 0 0 1 0 0.93 1 1 0 0 1 0 2.58

0 1 0 0 1 1 0.98 1 1 0 0 1 1 2.63

0 1 0 1 0 0 1.03 1 1 0 1 0 0 2.68

0 1 0 1 0 1 1.08 1 1 0 1 0 1 2.73

0 1 0 1 1 0 1.13 1 1 0 1 1 0 2.78

0 1 0 1 1 1 1.19 1 1 0 1 1 1 2.84

0 1 1 0 0 0 1.24 1 1 1 0 0 0 2.89

0 1 1 0 0 1 1.29 1 1 1 0 0 1 2.94

0 1 1 0 1 0 1.34 1 1 1 0 1 0 2.99

Publication Release Date: April 7 , 2009

-63- Version 1.94

W83627EHF/EF

W83627EHG

BIT

OUTPUT

VOLTAGE

BIT

OUTPUT

VOLTAGE

0 1 1 0 1 1 1.39 1 1 1 0 1 1 3.04

0 1 1 1 0 0 1.44 1 1 1 1 0 0 3.09

0 1 1 1 0 1 1.50 1 1 1 1 0 1 3.15

0 1 1 1 1 0 1.55 1 1 1 1 1 0 3.20

0 1 1 1 1 1 1.60 1 1 1 1 1 1 3.25

Table 7.4 .

7.9.5 CPUFANOUT0 PWM Output Frequency Configuration Register - Index 02h (Bank 0)

Power on Default Value: 04h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

PWM_CLK_SEL2

PWM_SCALE2

The register is meaningful when CPUFANOUT0 be programmed as PWM output.

Bit 7: CPUFANOUT0 PWM Input Clock Source Select. This bit selects the clock source of PWM output

frequency.

Set to 0, select 24 MHz.

Set to 1, select 180 KHz.

Bit 6-0: CPUFANOUT0 P WM Pre-Scale divider. Thi s is the divider of clock source o f PWM output

frequency. The maximum divider is 128 (7Fh). This divider should not be set to 0.

01h : divider is 1

02h : divider is 2

03h : divider is 3

- 64 -

W83627EHF/EF

W83627EHG/EG

the formula is PWM output frequency = 256

Divider Pre_Scale

ClockInput ∗

7.9.6 CPUFANOUT0 Output Value Select Register - Index 03h (Bank 0)

Power on Default Value: FFh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT0 Value

(1)If CPUFANOUT0 be programmed as PWM output (Bank0 Index 04h.bit1 is 0)

Bit 7-0: CPUFANOUT0 PWM Duty Cycle. Write FFh, CPUFANOUT0 duty cycle is 100%. Write 00h,

CPUFANOUT duty cycle is 0%.

Note. XXh: PWM Duty Cycle output percentage is (XX/256*100%) during one cycle.

(2)If CPUFANOUT0 be programmed as DC Voltag e output (Bank0 Index 04h.bit1 is 1)

Bit 7-2: CPUFANOUT0 voltage control.

Bit 1-0: Reserved.

OUTPUT Voltage = 64

*FANOUT

AVCC

Note. See the Table 7.4

7.9.7 FAN Configuration Register I - Index 04h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-65- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

SYSFANOUT_SEL

CPUFANOUT0_SEL

SYSFANOUT_Mode

CPUFANOUT0_Mod

Reserved

Bit 7-6: Reserved

Bit 5-4: CPUFANOUT0 mode control.

Set 00, CPUFANOUT0 is as Manual Mode. (Default).

Set 01, CPUFANOUT0 is as Thermal Cruise Mode.

Set 10, CPUFANOUT0 is as Fan Speed Cruise Mode.

Set 11, CPUFANOUT0 is as SMART FANTM III Mode

Bit 3-2: SYSFANOUT mode control.

Set 00, SYSFANOUT is as Manual Mode. (Default).

Set 01, SYSFANOUT is as Thermal Cruise Mode.

Set 10, SYSFANOUT is as Fan Speed Cruise Mode.

Set 11, Reserved and no function.

Bit 1: CPUFANOUT0 output mode selection. Set to 0, CPUFANOUT0 pin is as PWM output duty

cycle so that it can drive a logical high or low signal. Set to 1, CPUFANOUT0 pin is as DC

voltage output which can provide analog voltage output. (Default 0)

Bit 0: SYSFANOUT output mode selection. Set to 0, SYSFANOUT pin is as PWM duty cycle output

so that it can drive a logical high or low signal. Set to 1, SYSFANOUT pin is as DC voltage

output which can provide analog voltage output. (Default 1)

7.9.8 SYSTIN Target Temperature Register/ SYSFANIN Target Speed Register - Index 05h

(Bank 0)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

- 66 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

Target Temperature / Target Speed

(1)When at Thermal Cruise mode:

Bit 7: Reserved.

Bit 6-0: SYSTIN Target Temperature.

(2)When at Fan Speed Cruise mode:

Bit 7-0: SYSFANIN Target Speed.

7.9.9 CPUTIN Target Temperature Register/ CPUFANIN0 Target Speed Register - Index

06h (Bank 0)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Target Temperature / Target Speed

(1)When at Thermal Cruise mode or SMARTFAN III mode:

Bit 7: Reserved.

Bit 6-0: CPUTIN Target Temperature.

(2)When at Fan Speed Cruise mode:

Bit 7-0: CPUFANIN0 Target Speed.

7.9.10 Tolerance of Target Temperature or Target Speed Register - Index 07h (Bank 0)

Publication Release Date: April 7 , 2009

-67- Version 1.94

W83627EHF/EF

W83627EHG

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

SYSTIN Target Temperature Tolerance

/ SYSFANIN Target Speed Tolerance

CPUTIN Target Temperature Tolerance

/ CPUFANIN0 Target Speed Tolerance

(1)When at Thermal Cruise mode or SMARTFAN III mode:

Bit 7-4: Tolerance of CPUTIN Target Temperature.

Bit 3-0: Tolerance of SYSTIN Target Temperature.

(2)When at Fan Speed Cruise mode:

Bit 7-4: Tolerance of CPUFANIN0 Target Speed.

Bit 3-0: Tolerance of SYSFANIN Target Speed.

7.9.11 SYSFANOUT Stop Value Register - Index 08h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

SYSFANOUT Stop Value

When at Thermal Cruise mode, SYSFANOUT value will decrease to this value. This register should be

written a non-zero minimum stop value.

- 68 -

W83627EHF/EF

W83627EHG/EG

Please note that Stop Value does not mean that fan really stops. It means that if the temperature keeps

below low temperature limit, then the fan speed keeps on decreasing until reaching a minimam value,

and this is Stop Value.

7.9.12 CPUFANOUT0 Stop Value Register - Index 09h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT0 Stop Value

When at Thermal Cruise mode or SMARTFAN III mode, CPUFANOUT0 value will decrease to this

value. This register should be written a non-zero minimum stop value.

Please note that Stop Value does not mean that fan really stops. It means that if the temperature keeps

below low temperature limit, then the fan speed keeps on decreasing until reaching a minimam value,

and this is Stop Value.

7.9.13 SYSFANOUT Start-up Value Register - Index 0Ah (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-69- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

SYSFANOUT Start-up Value

When at Thermal Cruise mode, SYSFANOUT value will increase from 0 to this register value to provide

a minimum value to turn on the fan.

7.9.14 CPUFANOUT0 Start-up Value Register - Index 0Bh (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT0 Start-up Value

When at Thermal Cruise mode, CPUFANOUT0 value will increase from 0 to this register value to

provide a minimum value to turn on the fan.

7.9.15 SYSFANOUT Stop Time Register - Index 0Ch (Bank 0)

Power on Default Value: 3Ch

Attribute: Read/Write

Size: 8 bits

- 70 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

SYSFANOUT Stop Time

When at Thermal Cruise mode, this register determines the time of which SYSFANOUT value is from

stop value to 0.

(1)When at PWM output:

The unit of this register is 0.1 second. The default time is 6 seconds.

(2)When at DC Voltage output:

The unit of this register is 0.4 second. The default time is 24 seconds.

7.9.16 CPUFANOUT0 Stop Time Register - Index 0Dh (Bank 0)

Power on Default Value: 3Ch

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT0 Stop Time

When at Thermal Cruise mode or SMARTFAN III mode, this register determines the time of which

CPUFANOUT0 value is from stop value to 0.

(1)When at PWM output:

The unit of this register is 0.1 second. The default time is 6 seconds.

(2)When at DC Voltage output:

The unit of this register is 0.4 second. The default time is 24 seconds.

Publication Release Date: April 7 , 2009

-71- Version 1.94

W83627EHF/EF

W83627EHG

7.9.17 Fan Output Step Down Time Register - Index 0Eh (Bank 0)

Power on Default Value: 0Ah

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

FANOUT Value Step Down Time

This register determines the speed of FANOUT decreasing its value in Smart Fan Control mode.

(1)When at PWM output:

The unit of this register is 0.1 second. The default time is 1 seconds.

(2)When at DC Voltage output:

The unit of this register is 0.4 second. The default time is 4 seconds.

7.9.18 Fan Output Step Up Time Register - Index 0Fh (Bank 0)

Power on Default Value: 0Ah

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

FANOUT Value Step Up Time

- 72 -

W83627EHF/EF

W83627EHG/EG

This register determines the speed of FANOUT increasing the its value in Smart Fan Control mode.

(1)When at PWM output:

The unit of this register is 0.1 second. The default time is 1 seconds.

(2)When at DC Voltage output:

The unit of this register is 0.4 second. The default time is 4 seconds.

7.9.19 AUXFANOUT PWM Output Frequency Configuration Register - Index 10h (Bank 0)

Power on Default Value: 04h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

PWM_CLK_SEL3

PWM_SCALE3

The register is meaningful when AUXFANOUT be programmed as PWM output.

Bit 7: AUXFANOUT PWM Input Clock Source Select. This bit selects the clock source of PWM output

frequency.

Set to 0, select 24 MHz.

Set to 1, select 180 KHz.

Bit 6-0: AUXFANOUT PWM Pre-Scale divider. This is the divider of clock source of PWM output

frequency. The maximum divider is 128 (7Fh). This divider should not be set to 0.

01h : divider is 1

02h : divider is 2

03h : divider is 3

Publication Release Date: April 7 , 2009

-73- Version 1.94

W83627EHF/EF

W83627EHG

the formula is PWM output frequency = 256

Divider Pre_Scale

ClockInput ∗

7.9.20 AUXFANOUT Output Value Select Register - Index 11h (Bank 0)

Power on Default Value: FFh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

AUXFANOUT Value

(1)If AUXFANOUT be programmed as PWM output (Bank0 Index 12h.bit0 is 0)

Bit 7-0: AUXFANOUT PWM Duty Cycle. Write FFh, AUXFANOUT duty cycle is 100%. Write 00h,

AUXFANOUT duty cycle is 0%.

Note. XXh: PWM Duty Cycle output percentage is (XX/256*100%) during one cycle.

(2)If AUXFANOUT be programmed as DC Voltage output (Bank0 Index 12h.bit0 is 1)

Bit 7-2: AUXFANOUT voltage control.

Bit 1-0: Reserved.

OUTPUT Voltage = 16

*FANOUT

AVCC

Note. See the Table 7.4

7.9.21 FAN Configuration Register II - Index 12h (Bank 0)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

- 74 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

AUXFANOUT_SEL

AUXFANOUT_Mode

AUXFANOUT_MIN_Value

CPUFANOUT0_MIN_Value

SYSFANOUT_MIN_Value

CPUFANOUT1_MIN_Value

Reserved

Bit 7: Reserved

Bit 6: Set 1, CPUFANOUT1 value will decrease to and keep the value set in Index 64h when

temperature goes below target range. This is to maintain the fan speed in a minimum value.

Set 0, CPUFANOUT1 value will decrease to 0 when temperature goes below target range.

Bit 5: Set 1, SYSFANOUT value will decrease to and keep the value set in Index 08h when temperature

goes below target range. This is to maintain the fan speed in a minimum value.

Set 0, SYSFANOUT value will decrease to 0 when temperature goes below target range.

Bit 4: Set 1, CPUFANOUT0 value will decrease to and keep the value set in Index 09h when

temperature goes below target range. This is to maintain the fan speed in a minimum value.

Set 0, CPUFANOUT0 value will decrease to 0 when temperature goes below target range.

Bit 3: Set 1, AUXFANOUT value will decrease to and keep the value set in Index 17h when

temperature goes below target range. This is to maintain the fan speed in a minimum value.

Set 0, AUXFANOUT value will decrease to 0 when temperature goes below target range.

Bit 2-1: AUXFANOUT mode control.

Set 00, AUXFANOUT is as Manual Mode. (Default).

Set 01, AUXFANOUT is as Thermal Cruise Mode.

Set 10, AUXFANOUT is as Fan Speed Cruise Mode.

Set 11, reserved and no function.

Bit 0: AUXFANOUT output mode selection. Set to 0, AUXFANOUT pin is as PWM output duty cycle

so that it can drive a logical high or low signal. Set to 1, AUXFANOUT pin is as DC voltage output which

can provide analog voltage output. (Default 0)

7.9.22 AUXTIN Target Temperature Register/ AUXFANIN0 Target Speed Register - Index

13h (Bank 0)

Power on Default Value: 00h

Publication Release Date: April 7 , 2009

-75- Version 1.94

W83627EHF/EF

W83627EHG

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Target Temperature / Target Speed

(1)When at Thermal Cruise mode:

Bit 7: Reserved.

Bit 6-0: AUXTIN Target Temperature.

(2)When at Fan Speed Cruise mode:

Bit 7-0: AUXFANIN0 Target Speed.

7.9.23 Tolerance of Target Temperature or Target Speed Register - Index 14h (Bank 0)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

AUXTIN Target Temperature Tolerance

/ AUXFANIN Target Speed Tolerance

Reserved

(1)When at Thermal Cruise mode:

Bit 3-0: Tolerance of AUXTIN Target Temperature.

(2)When at Fan Speed Cruise mode:

- 76 -

W83627EHF/EF

W83627EHG/EG

Bit 3-0: Tolerance of AUXFANIN0 Target Speed.

7.9.24 AUXFANOUT Stop Value Register - Index 15h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

AUXFANOUT Stop Value

When at Thermal Cruise mode, AUXFANOUT value will decrease to this value. This register should be

written a non-zero minimum output value.

Please note that Stop Value does not mean that fan really stops. It means that if the temperature keeps

below low temperature limit, then the fan speed keeps on decreasing until reaching a minimam value,

and this is Stop Value.

7.9.25 AUXFANOUT Start-up Value Register - Index 16h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-77- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

AUXFANOUT Start-up Value

When at Thermal Cruise mode, AUXFANOUT value will increase from 0 to this register value to provide

a minimum value to turn on the fan.

7.9.26 AUXFANOUT Stop Time Register - Index 17h (Bank 0)

Power on Default Value: 3Ch

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

AUXFANOUT Stop Time

When at Thermal Cruise mode, this register determines the time of which AUXFANOUT value is from

stop value to 0.

(1)When at PWM output:

The unit of this register is 0.1 second. The default time is 6 seconds.

(2)When at DC Voltage output:

The unit of this register is 0.4 second. The default time is 24 seconds.

7.9.27 OVT# Configuration Register - Index 18h (Bank 0)

Power on Default Value: 43h

- 78 -

W83627EHF/EF

W83627EHG/EG

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Reserved

OVT1_Mod

Reserved

DIS_OVT1

Reserved

Bit 7: Reserved.

Bit 6: Set to 1, disable temperature sensor SYSTIN over-temperature (OVT#) output. Set to 0, enable

the SYSTIN OVT# output.

Bit 5: Reserved.

Bit 4: SYSTIN OVT# mode select. This bit default is set to 0, which is compared mode. When set to 1,

interrupt mode will be selected.

Bit 3-1: Reserved.

Bit 0: Reserved.

7.9.28 Reserved - Index 19h-1Fh (Bank 0)

7.9.29 Value RAM ⎯ Index 20h- 3Fh (Bank 0)

ADDRESS A6-A0 DESCRIPTION

20h CPUVCORE reading

21h VIN0 reading

22h AVCC reading

23h 3VCC reading

24h VIN1 reading

25h VIN2 reading

26h VIN3 reading

27h SYSTIN temperature sensor reading

Publication Release Date: April 7 , 2009

-79- Version 1.94

W83627EHF/EF

W83627EHG

ADDRESS A6-A0 DESCRIPTION

28h SYSFANIN reading

Note: This location stores the number of counts of the

internal clock per revolution.

29h CPUFANIN0 reading

Note: This location stores the number of counts of the

internal clock per revolution.

2Ah AUXFANIN0 reading

Note: This location stores the number of counts of the

internal clock per revolution.

2Bh CPUVCORE High Limit

2Ch CPUVCORE Low Limit

2Dh VIN0 High Limit

2Eh VIN0 Low Limit

2Fh AVCC High Limit

30h AVCC Low Limit

31h 3VCC High Limit

32h 3VCC Low Limit

33h VIN1 High Limit

34h VIN1 Low Limit

35h VIN2 High Limit

36h VIN2 Low Limit

37h VIN3 High Limit

38h VIN3 Low Limit

- 80 -

W83627EHF/EF

W83627EHG/EG

ADDRESS A6-A0 DESCRIPTION

39h SYSTIN temperature sensor High Limit

3Ah SYSTIN temperature sensor Hysteresis Limit

3Bh SYSFANIN Fan Count Limit

Note: It is the number of counts of the internal clock for

the Low Limit of the fan speed.

3Ch CPUFANIN0 Fan Count Limit

Note: It is the number of counts of the internal clock for

the Low Limit of the fan speed.

3Dh AUXFANIN0 Fan Count Limit

Note: It is the number of counts of the internal clock for

the Low Limit of the fan speed.

3Eh CPUFANIN1 Fan Count Limit

Note: It is the number of counts of the internal clock for

the Low Limit of the fan speed.

3Fh CPUFANIN1 reading

Note: This location stores the number of counts of the

internal clock per revolution.

7.9.30 Configuration Register - Index 40h (Bank 0)

Power on Default Value: 03h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-81- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

START

SMI#Enable

Reserved

INT_Clear

Reserved

INITIALIZATION

Bit 7: A one restores power on default value to some registers. This bit clears itself since the power on

default is zero.

Bit 6: Reserved

Bit 5: Reserved

Bit 4: Reserved

Bit 3: A one disables the SMI# output without affecting the contents of Interrupt Status Registers. The

device will stop monitoring. It will resume upon clearing of this bit.

Bit 2: Reserved

Bit 1: A one enables the SMI# Interrupt output.

Bit 0: A one enables startup of monitoring operations, a zero puts the part in standby mode.

Note: The outputs of Interrupt pins will not be cleared if the user writes a zero to this location after an

interrupt has occurred unlike "INT_Clear'' bit.

7.9.31 Interrupt Status Register 1 - Index 41h (Bank 0)

Power on Default Value: 00h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

CPUVCORE

VIN0

AVCC(Pin114)

3VCC

SYSTIN

CPUTIN

SYSFANIN

CPUFANIN0

Bit 7: A one indicates the fan count limit of CPUFANIN0 has been exceeded.

- 82 -

W83627EHF/EF

W83627EHG/EG

Bit 6: A one indicates the fan count limit of SYSFANIN has been exceeded.

Bit 5: A one indicates a High limit of CPUTIN temperature has been exceeded.

Bit 4: A one indicates a High limit of SYSTIN temperature has been exceeded.

Bit 3: A one indicates a High or Low limit of 3VCC has been exceeded.

Bit 2: A one indicates a High or Low limit of AVCC has been exceeded.

Bit 1: A one indicates a High or Low limit of VIN0 has been exceeded.

Bit 0: A one indicates a High or Low limit of CPUVCORE has been exceeded.

7.9.32 Interrupt Status Register 2 - Index 42h (Bank 0)

Power on Default Value: 00h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

VIN1

VIN3

VIN2

AUXFANIN0

CASEOPEN

AUXTIN

TAR1

TAR2

Bit 7: A one indicates that the CPUTIN temperature has been over the target temperature for 3 minutes

with full fan speed at thermal cruise mode of SmartFanTM.

Bit 6: A one indicates that the SYSTIN temperature has been over the target temperature for 3 minutes

with full fan speed at thermal cruise mode of SmartFanTM.

Bit 5: A one indicates a High limit of AUXTIN temperature has been exceeded.

Bit 4: A one indicates case has been opened.

Bit 3: A one indicates the fan count limit of AUXFANIN0 has been exceeded.

Bit 2: A one indicates a High or Low limit of VIN2 has been exceeded.

Bit 1: A one indicates a High or Low limit of VIN3 has been exceeded.

Bit 0: A one indicates a High or Low limit of VIN1 has been exceeded.

7.9.33 SMI# Mask Register 1 - Index 43h (Bank 0)

Power on Default Value: DEh

Publication Release Date: April 7 , 2009

-83- Version 1.94

W83627EHF/EF

W83627EHG

Attribute: Read/Write

Size: 8 bits

CPUVCORE

7 6 5 4 3 2 1 0

VIN0

AVCC(Pin114)

3VCC

SYSTIN

CPUTIN

SYSFANIN

CPUFANIN0

Bit 7-0: A one disables the corresponding interrupt status bit for SMI interrupt.

7.9.34 SMI# Mask Register 2 - Index 44h (Bank 0)

Power on Default Value: FFh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

VIN1

VIN3

VIN2

AUXFANIN0

CASEOPEN

AUXTIN

TAR1

TAR2

Bit 7-0: A one disables the corresponding interrupt status bit for SMI interrupt.

7.9.35 Reserved Register - Index 45h (Bank 0)

7.9.36 SMI# Mask Register 3 - Index 46h (Bank 0)

Power on Default Value: 07h

Attribute: Read/Write

Size: 8 bits

- 84 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

VIN4

CPUFANIN1

AUXFANIN1

Reserved

CaseOpen Clea

Bit 7: CASEOPEN Clear Control. Write 1 to this bit will clear CASEOPEN status. This bit won’t be self

cleared, please write 0 after event be cleared. The function is as same as LDA, CR[E6h] bit 5.

Bit 6-3: Reserved.

Bit 2-0: A one disables the corresponding interrupt status bit for SMI interrupt.

7.9.37 Fan Divisor Register I - Index 47h (Bank 0)

Power on Default Value: 55h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

FANINC5

FANOPV5

FANINC4

FANOPV4

SYSFANIN DIV_B0

SYSFANIN DIV_B1

CPUFANIN0 DIV_B0

CPUFANIN0 DIV_B1

Bit 7-6: CPUFANIN0 Divisor bit1:0.

Bit 5-4: SYSFANIN Divisor bit1:0.

Bit 3: CPUFANIN1 output value if bit 0 sets to 0. Write 1, pin119(CPUFANIN1) always generates a

logic high signal. Write 0, pin119 always generates a logic low signal. This bit is default 0.

Bit 2: CPUFANIN1 Input Control. Set to 1, pin119 (CPUFANIN1) acts as FAN tachometer input, which

is default value. Set to 0, this pin119 acts as FAN control signal and the output value of FAN

control is set by this register bit 1.

Bit 1: AUXFANIN1 output value if bit 0 sets to 0. Write 1, pin58(AUXFANIN1) always generates a logic

high signal. Write 0, pin58 always generates a logic low signal. This bit is default 0.

Publication Release Date: April 7 , 2009

-85- Version 1.94

W83627EHF/EF

W83627EHG

Bit 0: AUXFANIN1 Input Control. Set to 1, pin58 (AUXFANIN1) acts as FAN tachometer input, which is

default value. Set to 0, this pin58 acts as FAN control signal and the output value of FAN control

is set by this register bit 1.

Note : Please refer to Bank0 Index 5Dh , Fan divisor table.

7.9.38 Serial Bus Address Register - Index 48h (Bank 0)

Power on Default Value: 2Dh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Reserved

Serial Bus Addr.

Bit 7: Reserved (Read Only).

Bit 6-0: Serial Bus address <7:1>.

7.9.39 Reserved - Index 49h (Bank 0)

7.9.40 CPUFANOUT1 with Temperature source Select - Index 4Ah (Bank 0)

Power on Default Value: 64h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Reserved

CPUFANOUT1 SR

- 86 -

W83627EHF/EF

W83627EHG/EG

Bit 7-6: Select Temperature source for CPUFANOUT1 at Thermal Cruise mode or SMART FANTM III

Mode

<7:6> = 00 – SYSTIN.

<7:6> = 01 - CPUTIN.(Default)

<7:6> = 10 - AUXTIN.

<7:6> = 11 – Reserved.

Bit 5-0: Reserved.

7.9.41 Fan Divisor Register II - Index 4Bh (Bank 0)

Power on Default Value: 44h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Reserved

ADCOVSEL

AUXFANIN0 DIV_B0

AUXFANIN0 DIV_B1

Bit 7-6: AUXFANIN0 Divisor bit1:0.

Note : Please refer to Bank0 Index 5Dh , Fan divisor table.

Bit 5-4: Select A/D Converter Clock Input.

<5:4> = 00 - default. ADC clock select 22.5 Khz.

<5:4> = 01- ADC clock select 5.6 Khz. (22.5K/4)

<5:4> = 10 - ADC clock select 1.4Khz. (22.5K/16)

<5:4> = 11 - ADC clock select 0.35 Khz. (22.5K/64)

Bit 3-2: These two bits should be set to 01h. The default value is 01h.

Bit 1-0: Reserved.

7.9.42 SMI#/OVT# Control Register - Index 4Ch (Bank 0)

Publication Release Date: April 7 , 2009

-87- Version 1.94

W83627EHF/EF

W83627EHG

Power on Default Value: 10h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

Reserved

OVTPOL

DIS_OVT2

DIS_OVT3

EN_T1_ONE

T2T3_INTMode

CPUFANIN1 DIV_B

Bit 7: CPUFANIN1 Divisor bit2.

Bit 6: Set to 1, the SMI# output type of Temperature CPUTIN/AUXTIN is set to Comparator Interrupt

mode. Set to 0, the SMI# output type is set to Two-Times Interrupt mode. (Default 0)

Bit 5: Set to 1, the SMI# output type of temperature SYSTIN is One-Time interrupt mode. Set to 0, the

SMI# output type is Two-Times interrupt mode.

Bit 4: Disable temperature sensor AUXTIN over-temperature (OVT) output if set to 1. Set to 0, enable

AUXTIN OVT output through pin OVT#. (Default 1)

Bit 3: Disable temperature sensor CPUTIN over-temperature (OVT) output if set to 1. Set to 0, enable

CPUTIN OVT output through pin OVT#. (Default 0)

Bit 2: Over-temperature polarity. Write 1, OVT# active high. Write 0, OVT# active low. (Default 0)

Bit 1-0: Reserved.

7.9.43 FAN IN/OUT Control Register - Index 4Dh (Bank 0)

Power on Default Value: 15h

Attribute: Read/Write

Size: 8 bits

- 88 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

FANINC1

FANOPV1

FANINC2

FANOPV2

FANINC3

FANOPV3

Reserved

Bit 7-6: Reserved.

Bit 5: AUXFANIN0 output value if bit 4 sets to 0. Write 1, pin111(AUXFANIN0) always generates a logic

high signal. Write 0, pin111 always generates a logic low signal. This bit is default 0.

Bit 4: AUXFANIN0 Input Control. Set to 1, pin111(AUXFANIN0) acts as FAN tachometer input, which is

default value. Set to 0, this pin111 acts as FAN control signal and the output value of FAN control

is set by this register bit 5.

Bit 3: CPUFANIN0 output value if bit 2 sets to 0. Write 1, pin112(CPUFANIN0) always generates a

logic high signal. Write 0, pin112 always generates a logic low signal. This bit is default 0.

Bit 2: CPUFANIN0 Input Control. Set to 1, pin112(CPUFANIN0) acts as FAN tachometer input, which is

default value. Set to 0, this pin112 acts as FAN control signal and the output value of FAN control

is set by this register bit 3.

Bit 1: SYSFANIN output value if bit 0 sets to 0. Write 1, pin113(SYSFANIN) always generates a logic

high signal. Write 0, pin113 always generates a logic low signal. This bit is default 0.

Bit 0: SYSFANIN Input Control. Set to 1, pin113(SYSFANIN) acts as FAN tachometer input, which is

default value. Set to 0, this pin113 acts as FAN control signal and the output value of FAN control

is set by this register bit 1.

7.9.44 Register 50h ~ 5Fh Bank Select Register - Index 4Eh (Bank 0)

Power on Default Value: 80h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-89- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

BANKSEL0

BANKSEL1

BANKSEL2

Reserved

EN_CPUFANIN1_BP

EN_AUXFANIN1_BP

Reserved

HBACS

Bit 7: HBACS - High byte access. Set to 1, access Index 4Fh high byte register.

Set to 0, access Index 4Fh low byte register. (default 1)

Bit 6: Reserved. This bit should be set to 0.

Bit 5: BEEP output control for AUXFANIN1 if the monitor value exceeds the limit value. Write 1, enable

BEEP output. Write 0, disable BEEP output, which is default value.

Bit 4: BEEP output control for CPUFANIN1 if the monitor value exceeds the limit value. Write 1, enable

BEEP output. Write 0, disable BEEP output, which is default value.

Bit 3: Reserved. This bit should be set to 0.

Bit 2-0: Index ports 0x50~0x5F Bank select.

Set to 0, select Bank0.

Set to 1, select Bank1.

Set to 2, select Bank2.

Set to 3, select Bank3.

Set to 4, select Bank4.

Set to 5, select Bank5.

Set to 6, select Bank6.

Set to 7, select Bank7.

7.9.45 Nuvoton Vendor ID Register - Index 4Fh (Bank 0)

Power on Default Value: <15:0> = 5CA3h

Attribute: Read Only

Size: 16 bits

- 90 -

W83627EHF/EF

W83627EHG/EG

15 8 7 0

VIDH

VIDL

Bit 15-8: Vendor ID High Byte if Index 4Eh.bit7=1. Default 5Ch.

Bit 7-0: Vendor ID Low Byte if Index 4Eh.bit7=0. Default A3h.

7.9.46 Nuvoton Test Register - Index 50h-55h (Bank 0)

7.9.47 BEEP Control Register 1 - Index 56h (Bank 0)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

EN_CPUVCORE_B

EN_VIN0_BP

EN_AVCC_BP

EN_3VCC_BP

EN_SYSTIN_BP

EN_CPUTIN_BP

EN_SYSFANIN_BP

EN_CPUFANIN0_B

Bit 7: BEEP output control for CPUFANIN0 if the monitor value exceeds the limit value. Write 1, enable

BEEP output. Write 0, disable BEEP output, which is default value.

Bit 6: BEEP output control for SYSFANIN if the monitor value exceeds the limit value. Write 1, enable

BEEP output. Write 0, disable BEEP output, which is default value.

Bit 5: BEEP output control for temperature CPUTIN if the monitor value exceeds the limit value. Write 1,

enable BEEP output. Write 0, disable BEEP output, which is default value.

Bit 4: BEEP output control for temperature SYSTIN if the monitor value exceeds the limit value. Write 1,

enable BEEP output. Write 0, disable BEEP output, which is default value.

Bit 3: BEEP output control for 3VCC if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

Publication Release Date: April 7 , 2009

-91- Version 1.94

W83627EHF/EF

W83627EHG

Bit 2: BEEP output control for AVCC if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

Bit 1: BEEP output control for VIN0 if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

Bit 0: BEEP output control for CPUVCORE if the monitor value exceeds the limit value. Write 1, enable

BEEP output. Write 0, disable BEEP output, which is default value.

7.9.48 BEEP Control Register 2 - Index 57h (Bank 0)

Power on Default Value: 80h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

EN_VIN1_BP

EN_VIN2_BP

EN_VIN3_B

EN_AUXFANIN0_B

EN_CASEOPEN_B

EN_AUXTIN_BP

EN_VIN4_BP

EN_GBP

Bit 7: Global BEEP Control. Write 1, enable global BEEP output, which is default value. Write 0, disable

all BEEP output.

Bit 6: BEEP output control for VIN4 if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

Bit 5: BEEP output control for temperature AUXTIN if the monitor value exceeds the limit value. Write 1,

enable BEEP output. Write 0, disable BEEP output, which is default value.

Bit 4: BEEP output control for CASEOPEN if case has been opened. Write 1, enable BEEP output.

Write 0, disable BEEP output, which is default value.

Bit 3: BEEP output control for AUXFANIN0 if the monitor value exceeds the limit value. Write 1, enable

BEEP output. Write 0, disable BEEP output, which is default value.

Bit 2: BEEP output control for VIN3 if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

Bit 1: BEEP output control for VIN2 if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

- 92 -

W83627EHF/EF

W83627EHG/EG

Bit 0: BEEP output control for VIN1 if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

7.9.49 Chip ID - Index 58h (Bank 0)

Power on Default Value: A1h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

CHIPID

Bit 7-0: Nuvoton Chip ID number. Read this register will return A1h.

7.9.50 Diode Selection Register - Index 59h (Bank 0)

Power on Default Value: 70h

Attribute: Read/Write

Size: 8 bits

Bit 7: AUXFANIN1 Divisor bit2.

CPUFANIN1 DIV_B0

CPUFANIN1 DIV_B1

SELPIIV1

SELPIIV2

SELPIIV3

AUXFANIN1 DIV_B2

7 6 5 4 3 2 1 0

AUXFANIN1 DIV_B0

AUXFANIN1 DIV_B1

Bit 6: Diode mode selection of temperature AUXTIN if Index 5Dh bit3 is 1. Set this bit to 1, select

Pentium II CPU compatible thermal diode.

Bit 5: Diode mode selection of temperature CPUTIN if Index 5Dh bit2 is 1. Set this bit to 1, select

Pentium II CPU compatible thermal diode.

Bit 4: Diode mode selection of temperature SYSTIN if Index 5Dh bit1 is 1. Set this bit to 1, select

Pentium II CPU compatible thermal diode.

Bit 3-2: AUXFANIN1 Divisor bit 1:0.

Publication Release Date: April 7 , 2009

-93- Version 1.94

W83627EHF/EF

W83627EHG

Bit 1-0: CPUFANIN1 Divisor bit 1:0.

7.9.51 Reserved - Index 5Ah-5Ch (Bank 0)

7.9.52 VBAT Monitor Control Register - Index 5Dh (Bank 0)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

EN_VBAT_MNT

DIODES1

DIODES2

DIODES3

Reserved

SYSFANIN DIV_B2

CPUFANIN0 DIV_B2

AUXFANIN0 DIV_B2

Bit 7: AUXFANIN0 Divisor bit2.

Bit 6: CPUFANIN0 Divisor bit2.

Bit 5: SYSFANIN Divisor bit2.

Bit 4: Reserved.

Bit 3: Sensor type selection of AUXTIN. Set to 1, select diode sensor. Set to 0, select thermistor sensor.

Bit 2: Sensor type selection of CPUTIN. Set to 1, select diode sensor. Set to 0, select thermistor

sensor.

Bit 1: Sensor type selection of SYSTIN. Set to 1, select diode sensor. Set to 0, select thermistor sensor.

Bit 0: Set to 1, enable battery voltage monitor. Set to 0, disable battery voltage monitor. After set this bit

from 0 to 1, the monitored value will be updated to the VBAT reading value register after one

monitor cycle time.

Fan divisor table:

BIT 2 BIT 1 BIT 0 FAN DIVISOR BIT 2 BIT 1 BIT 0 FAN DIVISOR

0 0 0 1 1 0 0 16

- 94 -

W83627EHF/EF

W83627EHG/EG

BIT 2 BIT 1 BIT 0 FAN DIVISOR BIT 2 BIT 1 BIT 0 FAN DIVISOR

0 0 1 2 1 0 1 32

0 1 0 4 1 1 0 64

0 1 1 8 1 1 1 128

Table 7.3

7.9.53 Reserved Register - Index 5Eh-5Fh (Bank 0)

7.9.54 CPUFANOUT1 PWM Output Frequency Configuration Register - Index 60h (Bank 0)

Power on Default Value: 04h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

PWM_CLK_SEL4

PWM_SCALE4

The register is meaningful when CPUFANOUT1 be programmed as PWM output.

Bit 7: CPUFANOUT1 PWM Input Clock Source Select. This bit selects the clock source of PWM output

frequency.

Set to 0, select 24 MHz.

Set to 1, select 180 KHz.

Bit 6-0: CPUFANOUT1 PWM Pre-Scale divider. This is the divider of clock source of PWM output

frequency. The maximum divider is 128 (7Fh). This divider should not be set to 0.

01h : divider is 1

02h : divider is 2

03h : divider is 3

Publication Release Date: April 7 , 2009

-95- Version 1.94

W83627EHF/EF

W83627EHG

the formula is PWM output frequency = 256

Divider Pre_Scale

ClockInput ∗

7.9.55 CPUFANOUT1 Output Value Select Register - Index 61h (Bank 0)

Power on Default Value: FFh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT1 Value

(1)If CPUFANOUT1 be programmed as PWM output (Bank0 Index 62h.bit6 is 0)

Bit 7-0: CPUFANOUT1 PWM Duty Cycle. Write FFh, CPUFANOUT1 duty cycle is 100%. Write 00h,

CPUFANOUT1 duty cycle is 0%.

Note. XXh: PWM Duty Cycle output percentage is (XX/256*100%) during one cycle.

(2)If CPUFANOUT1 be programmed as DC Voltag e output (Bank0 Index 62h.bit6 is 1)

Bit 7-2: CPUFANOUT1 voltage control.

Bit 1-0: Reserved.

OUTPUT Voltage = 64

*FANOUT

AVCC

Note. See the Table 7.4

7.9.56 FAN Configuration Register III - Index 62h (Bank 0)

Power on Default Value: 40h

Attribute: Read/Write

Size: 8 bits

- 96 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

Reserved

CPUFANOUT1_SEL

CPUFANOUT1_Mode

Target Temperature Tolerance

/ CPUFANIN1 Target Speed Toleran

Bit7: Reserved.

Bit 6: CPUFANOUT1 output mode selection. Set to 0, CPUFANOUT1 pin is as PWM output duty

cycle so that it can drive a logical high or low signal. Set to 1, CPUFANOUT1 pin is as DC

voltage output which can provide analog voltage output. (Default 1)

Bit 5-4: CPUFANOUT1 mode control.

Set 00, CPUFANOUT1 is as Manual Mode. (Default).

Set 01, CPUFANOUT1 is as Thermal Cruise Mode.

Set 10, CPUFANOUT1 is as Fan Speed Cruise Mode.

Set 11, CPUFANOUT1 is SMART FANTM III Mode.

(1)When at Thermal Cruise mode or SMART FANTM III mode:

Bit3-0: Tolerance of select temperature source Target Temperature.

(2)When at Fan Speed Cruise mode:

Bit3-0: Tolerance of CPUFANIN1 Target Speed.

7.9.57 Target Temperature Register/ CPUFANIN1 Target Speed Register - Index 63h (Bank

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-97- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

Target Temperature / Target Speed

(1)When at Thermal Cruise mode or SMART FANTM III mode:

Bit 7: Reserved.

Bit 6-0: Target Temperature of select temperature source.

(2)When at Fan Speed Cruise mode:

Bit 7-0: CPUFANIN1 Target Speed.

7.9.58 CPUFANOUT1 Stop Value Register - Index 64h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT1 Stop Value

When at Thermal Cruise mode or SMART FANTM III mode, CPUFANOUT1 value will decrease to this

value. This register should be written a non-zero minimum stop value.

Please note that Stop Value does not mean that fan really stops. It means that if the temperature keeps

below low temperature limit, then the fan speed keeps on decreasing until reaching a minimam value,

and this is Stop Value.

7.9.59 CPUFANOUT1 Start-up Value Register - Index 65h (Bank 0)

- 98 -

W83627EHF/EF

W83627EHG/EG

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT1 Start-up Value

When at Thermal Cruise mode, CPUFANOUT1 value will increase from 0 to this register value to

provide a minimum value to turn on the fan.

7.9.60 CPUFANOUT1 Stop Time Register - Index 66h (Bank 0)

Power on Default Value: 3Ch

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT1 Stop Time

When at Thermal Cruise mode or SMART FANTM III mode, this register determines the time of which

CPUFANOUT1 value is from stop value to 0.

(1)When at PWM output:

The unit of this register is 0.1 second. The default time is 6 seconds.

(2)When at DC Voltage output:

The unit of this register is 0.4 second. The default time is 24 seconds.

Publication Release Date: April 7 , 2009

-99- Version 1.94

W83627EHF/EF

W83627EHG

7.9.61 CPUFANOUT0 Maximum Output Value Register - Index 67h (Bank 0)

Power on Default Value: FFh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT0 Max. Value

When at SMART FANTM III mode, CPUFANOUT0 value will increase to this value. This register should

be written a non-zero value that cannot lower than Stop value.

7.9.62 CPUFANOUT0 Output Step Value Register - Index 68h (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT0 Step

This register determines the value that CPUFANOUT0 in SMART FANTM III mode decreased or

increased to the next speed.

7.9.63 CPUFANOUT1 Maximum Output Value Register - Index 69h (Bank 0)

Power on Default Value: FFh

- 100 -

W83627EHF/EF

W83627EHG/EG

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT1 Max. Value

When at SMART FANTM III mode, CPUFANOUT1 value will increase to this value. This register should

be written a non-zero value that cannot lower than Stop value.

7.9.64 CPUFANOUT1 Output Step Value Register - Index 6Ah (Bank 0)

Power on Default Value: 01h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

CPUFANOUT1 Step

This register determines the value that CPUFANOUT1 in SMART FANTM III mode decreased or

increased to the next speed.

7.9.65 CPUTIN Temperature Sensor Temperature (High Byte) Register - Index 50h (Bank 1)

Attribute: Read Only

Size: 8 bits

Publication Release Date: April 7 , 2009

-101- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

TEMP<8:1>

Bit 7-0: Temperature <8:1> of CPUTIN sensor, which is high byte, means 1°C.

7.9.66 CPUTIN Temperature Sensor Temperature (Low Byte) Register - Index 51h (Bank 1)

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

TEMP<0>

Reserved

Bit 7: Temperature <0> of CPUTIN sensor, which is low byte, means 0.5°C.

Bit 6-0: Reserved.

7.9.67 CPUTIN Temperature Sensor Configuration Register - Index 52h (Bank 1)

Power on Default Value: 00h

Size: 8 bits

7 6 5 4 3 2 1 0

STOP

OVTMOD

Reserved

FAULT

Reserved

Bit 7-5: Read Only - Reserved. This bit should be set to 0.

- 102 -

W83627EHF/EF

W83627EHG/EG

Bit 4-3: Read/Write - Number of faults to detect before setting OVT# output to avoid false tripping due

to noise.

Bit 2: Read - Reserved. This bit should be set to 0.

Bit 1: Read/Write - OVT# mode select. This bit default is set to 0, which is compared mode. When set to

1, interrupt mode will be selected.

Bit 0: Read/Write - When set to 1 the sensor will stop monitor.

7.9.68 CPUTIN Temperature Sensor Hysteresis (High Byte) Register - Index 53h (Bank 1)

Power on Default Value: 4Bh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

THYST<8:1>

Bit 7-0: Temperature hysteresis bit 8-1, which is High Byte. The temperature default 75 degree C.

7.9.69 CPUTIN Temperature Sensor Hysteresis (Low Byte) Register - Index 54h (Bank 1)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

THYST<0>

Reserved

Bit 7: Hysteresis temperature bit 0, which is low Byte.

Bit 6-0: Reserved.

Publication Release Date: April 7 , 2009

-103- Version 1.94

W83627EHF/EF

W83627EHG

7.9.70 CPUTIN Temperature Sensor Over-temperature (High Byte) Register - Index 55h

(Bank1)

Power on Default Value: 50h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

TOVF<8:1>

Bit 7-0: Over-temperature bit 8-1, which is High Byte. The temperature default 80 degree C.

7.9.71 CPUTIN Temperature Sensor Over-temperature (Low Byte) Register - Index 56h

(Bank 1)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

TOVF<0>

Reserved

Bit 7: Over-temperature bit 0, which is low Byte.

Bit 6-0: Reserved.

7.9.72 AUXTIN Temperature Sensor Temperature (High Byte) Register - Index 50h (Bank 2)

Attribute: Read Only

Size: 8 bits

- 104 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

TEMP<8:1>

Bit 7: Temperature <8:1> of AUXTIN sensor, which is high byte, means 1°C.

7.9.73 AUXTIN Temperature Sensor Temperature (Low Byte) Register - Index 51h (Bank 2)

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

TEMP<0>

Reserved

Bit 7: Temperature <0> of AUXTIN sensor, which is low byte, means 0.5°C.

Bit 6-0: Reserved.

7.9.74 AUXTIN Temperature Sensor Configuration Register - Index 52h (Bank 2)

Power on Default Value: 00h

Size: 8 bits

7 6 5 4 3 2 1 0

STOP

OVTMOD

Reserved

FAULT

Reserved

Publication Release Date: April 7 , 2009

-105- Version 1.94

W83627EHF/EF

W83627EHG

Bit 7-5: Read - Reserved. This bit should be set to 0.

Bit 4-3: Read/Write - Number of faults to detect before setting OVT# output to avoid false tripping due

to noise.

Bit 2: Read - Reserved. This bit should be set to 0.

Bit 1: Read/Write - OVT# mode select. This bit default is set to 0, which is compared mode. When set to

1, interrupt mode will be selected.

Bit 0: Read/Write - When set to 1 the sensor will stop monitor.

7.9.75 AUXTIN Temperature Sensor Hysteresis (High Byte) Register - Index 53h (Bank 2)

Power on Default Value 4Bh

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

THYST<8:1>

Bit 7-0: Temperature hysteresis bit 8-1, which is High Byte. The temperature default 75 degree C.

7.9.76 AUXTIN Temperature Sensor Hysteresis (Low Byte) Register - Index 54h (Bank 2)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

- 106 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

THYST<0>

Reserved

Bit 7: Hysteresis temperature bit 0, which is low Byte.

Bit 6-0: Reserved.

7.9.77 AUXTIN Temperature Sensor Over-temperature (High Byte) Register - Index 55h

(Bank 2)

Power on Default Value: 50h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

TOVF<8:1>

Bit 7-0: Over-temperature bit 8-1, which is High Byte. The temperature default 80 degree C.

7.9.78 AUXTIN Temperature Sensor Over-temperature(Low Byte) Register - Index 56h

(Bank 2)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

Publication Release Date: April 7 , 2009

-107- Version 1.94

W83627EHF/EF

W83627EHG

7 6 5 4 3 2 1 0

TOVF<0>

Reserved

Bit 7: Over-temperature bit 0, which is low Byte.

Bit 6-0: Reserved.

7.9.79 Interrupt Status Register 3 - Index 50h (Bank 4)

Power on Default Value: 00h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

VSB

VBAT

TAR3

VIN4

CPUFANIN1

AUXFANIN1

Reserved

Bit 7-6: Reserved.

Bit 5: A one indicates the fan count limit of AUXFANIN1 has been exceeded.

Bit 4: A one indicates the fan count limit of CPUFANIN1 has been exceeded.

Bit 3: A one indicates a High or Low limit of VIN4 has been exceeded.

Bit 2: A one indicates that the AUXTIN temperature has been over the target temperature for 3 minutes

with full fan speed at thermal cruise mode of Smart FanTM.

Bit 1: A one indicates a High or Low limit of VBAT has been exceeded.

Bit 0: A one indicates a High or Low limit of VSB has been exceeded.

7.9.80 SMI# Mask Register 4 - Index 51h (Bank 4)

- 108 -

W83627EHF/EF

W83627EHG/EG

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

VSB

VBAT

Reserved

TAR3

Reserved

Bit 7-5: Reserved.

Bit 4: A one disables the corresponding interrupt status bit for SMI interrupt.

Bit 3-2: Reserved.

Bit 1: A one disables the corresponding interrupt status bit for SMI interrupt.

Bit 0: A one disables the corresponding interrupt status bit for SMI interrupt.

7.9.81 Reserved Register - Index 52h (Bank 4)

7.9.82 BEEP Control Register 3 - Index 53h (Bank 4)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

EN_VSB_BP

EN_VBAT_BP

Reserved

EN_USER_BP

Reserved

Bit 7-6: Reserved.

Bit 5: User define BEEP output function. Write 1, the BEEP is always active. Write 0, this function is

inactive. (Default 0)

Bit 4-2: Reserved.

Publication Release Date: April 7 , 2009

-109- Version 1.94

W83627EHF/EF

W83627EHG

Bit 1: BEEP output control for VBAT if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

Bit 0: BEEP output control for VSB if the monitor value exceeds the limit value. Write 1, enable BEEP

output. Write 0, disable BEEP output, which is default value.

7.9.83 SYSTIN Temperature Sensor Offset Register - Index 54h (Bank 4)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

OFFSET<7:0>

Bit 7-0: SYSTIN temperature offset value. The value in this register will be added to the monitored

value so that the reading value will be the sum of the monitored value and the offset value.

7.9.84 CPUTIN Temperature Sensor Offset Register - Index 55h (Bank 4)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

OFFSET<7:0>

Bit 7-0: CPUTIN temperature offset value. The value in this register will be added to the monitored

value so that the reading value will be the sum of the monitored value and the offset value.

- 110 -

W83627EHF/EF

W83627EHG/EG

7.9.85 AUXTIN Temperature Sensor Offset Register - Index 56h (Bank 4)

Power on Default Value: 00h

Attribute: Read/Write

Size: 8 bits

7 6 5 4 3 2 1 0

OFFSET<7:0>

Bit 7-0: AUXTIN temperature offset value. The value in this register will be added to the monitored

value so that the reading value will be the sum of the monitored value and the offset value.

7.9.86 Reserved Register - Index 57h-58h (Bank 4)

7.9.87 Real Time Hardware Status Register I - Index 59h (Bank 4)

Power on Default Value: 00h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

CPUVCORE_STS

VIN0_STS

AVCC_STS

3VCC_STS

SYSTIN_STS

CPUTIN_STS

SYSFANIN_STS

CPUFANIN0_STS

Bit 7: CPUFANIN0 status. Read 1, the fan speed count is over the limit value. Read 0, the fan speed

count is in the limit range.

Publication Release Date: April 7 , 2009

-111- Version 1.94

W83627EHF/EF

W83627EHG

Bit 6: SYSFANIN status. Read 1, the fan speed count is over the limit value. Read 0, the fan speed

count is in the limit range.

Bit 5: CPUTIN temperature sensor status. Read 1, the temperature exceeds the over-temperature limit

value. Read 0, the temperature is in under the hysteresis value.

Bit 4: SYSTIN temperature sensor status. Read 1, the temperature exceeds the over-temperature limit

value. Read 0, the temperature is in under the hysteresis value.

Bit 3: 3VCC Voltage status. Read 1, the voltage of 3VCC is over/under the limit value. Read 0, the

voltage of 3VCC is in the limit range.

Bit 2: AVCC Voltage status. Set 1, the voltage of AVCC is over/under the limit value. Read 0, the

voltage of AVCC is in the limit range.

Bit 1: VIN0 Voltage status. Set 1, the voltage of VIN0 is over/under the limit value. Read 0, the voltage

of VIN0 is in the limit range.

Bit 0: CPUVCORE Voltage status. Read 1, the voltage of CPUVCORE is over/under the limit value.

Read 0, the voltage of CPUVCORE is in the limit range.

7.9.88 Real Time Hardware Status Register II - Index 5Ah (Bank 4)

Power on Default Value: 00h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

VIN1_STS

TAR4_STS

CPUFANIN1_STS

AUXFANIN0_STS

CASEOPEN_STS

AUXTIN_STS

TAR1_STS

TAR2_STS

Bit 7: Smart Fan of CPUFANIN0 warning status. Read 1, the CPUTIN temperature has been over the

target temperature for 3 minutes with full fan speed at thermal cruise mode of SmartFanTM. Read

0, the temperature does not reach the warning range yet.

Bit 6: Smart Fan of SYSFANIN warning status. Read 1, the SYSTIN temperature has been over the

target temperature for 3 minutes with full fan speed at thermal cruise mode of SmartFanTM. Read

0, the temperature does not reach the warning range yet.

- 112 -

W83627EHF/EF

W83627EHG/EG

Bit 5: AUXTIN temperature sensor status. Read 1, the temperature exceeds the over-temperature limit

value. Read 0, the temperature is in under the hysteresis value.

Bit 4: Case Open status. Read 1, the case open is detected and latched. Read 0, the case is not

latched open.

Bit 3: AUXFANIN0 status. Read 1, the fan speed count is over the limit value. Read 0, the fan speed

count is in the limit range.

Bit 2: CPUFANIN1 status. Read 1, the fan speed count is over the limit value. Read 0, the fan speed

count is in the limit range.

Bit 1: Smart Fan of CPUFANIN1 warning status. Read 1, the select temperature has been over the

target temperature for 3 minutes with full fan speed at thermal cruise mode of SmartFanTM. Read

0, the temperature does not reach the warning range yet.

Bit 0: VIN1 Voltage status. Read 1, the voltage of VIN1 is over/under the limit value. Read 0, the

voltage of VIN1 is in the limit range.

7.9.89 Real Time Hardware Status Register III - Index 5Bh (Bank 4)

Power on Default Value: 00h

Attribute: Read Only

Size: 8 bits

7 6 5 4 3 2 1 0

VSB_STS

VBAT_STS

TAR3_STS

VIN4_STS

VIN3_STS

VIN2_STS

Reserved

AUXFANIN1_STS

Bit 7: AUXFANIN1 status. Read 1, the fan speed count is over the limit value. Read 0, the fan speed

count is in the limit range.

Bit 6: Reserved.

Bit 5: VIN2 Voltage status. Read 1, the voltage of VIN2 is over/under the limit value. Read 0, the

voltage of VIN21 is in the limit range.

Bit 4: VIN3 Voltage status. Read 1, the voltage of VIN3 is over/under the limit value. Read 0, the

voltage of VIN3 is in the limit range.

Publication Release Date: April 7 , 2009

-113- Version 1.94

W83627EHF/EF

W83627EHG

Bit 3: VIN4 Voltage status. Read 1, the voltage of VIN4 is over/under the limit value. Read 0, the

voltage of VIN4 is in the limit range.

Bit 2: Smart Fan of AUXFANIN warning status. Read 1, the AUXTIN temperature has been over the

target temperature for 3 minutes with full fan speed at thermal cruise mode of SmartFanTM. Read

0, the temperature does not reach the warning range yet.

Bit 1: VBAT Voltage status. Read 1, the voltage of VBAT is over/under the limit value. Read 0, the

voltage of VBAT is in the limit range.

Bit 0: VSB Voltage status. Read 1, the voltage of VSB is over/under the limit value. Read 0, the voltage

of VSB is in the limit range.

7.9.90 Reserved Register - Index 5Ch-5Dh (Bank 4)

7.9.91 Value RAM 2 ⎯ Index 50h-59h (Bank 5)

ADDRESS A6-A0 DESCRIPTION

50h VSB reading

51h VBAT reading. The reading is meaningless if EN_VBAT_MNT

bit(Bank0 Index 5Dh.bit0) is not set.

52h VIN4 reading

53h AUXFANIN1 reading

Note: This location stores the number of counts of the internal clock per

revolution.

54h 3VSB High Limit

55h 3VSB Low Limit

56h VBAT High Limit

57h VBAT Low Limit

58h VIN4 High Limit

59h VIN4 Low Limit

5Ah Reserved

5Bh Reserved

5Ch AUXFANIN1 Fan Count Limit

- 114 -

W83627EHF/EF

W83627EHG/EG

ADDRESS A6-A0 DESCRIPTION

Note: It is the number of counts of the internal clock for the Low Limit of

the fan speed.

7.9.92 Nuvoton Test Register - Index 50h-57h (Bank 6)

Publication Release Date: April 7 , 2009

-115- Version 1.94

W83627EHF/EF

W83627EHG

8. FLOPPY DISK CONTROLLER

8.1 FDC Functional Description

The floppy disk controller (FDC) of the W83627EHF/EHG/EF/EG integrates all of the logic required for

floppy disk control. The FDC implements a FIFO which provides better system performance in

multi-master systems, and the digital data separator supports data rates up to 2 M bits/sec.

The FDC includes the following blocks: Precompensation, Data Rate Selection, Digital Data Separator,

FIFO, and FDC Core. The rest of this section discusses these blocks through the following topics: FIFO,

Data Separator, Write Precompensation, Perpendicular Recording mode, FDC core, FDC commands,

and FDC registers.

8.1.1 FIFO (Data)

The FIFO is 16 bytes in size and has programmable threshold values. All command parameter

information and disk data transfers go through the FIFO. Data transfers are governed by the RQM

(Request for Master) and DIO (Data Input/Output) bits in the Main Status Register.

The FIFO is defaulted to disabled mode after any form of reset, which maintains PC/AT hardware

compatibility. The default values can be changed through the configure command. The advantage of

the FIFO is that it lets the system have a larger DMA latency without causing disk errors. The following

tables give several examples of the delays with the FIFO. The data are based upon the following

formula:

DELAY = THRESHOLD # x (1 / DATA RATE) * 8 - 1.5 μs

FIFO THRESHOLD MAXIMUM DELAY UNTIL SERVICING AT 500K BPS

Data Rate

1 Byte 1 x 16μs - 1.5 μs = 14.5 μs

2 Byte 2 x 16 μs - 1.5 μs = 30.5 μs

8 Byte 8 x 16 μs - 1.5 μs = 6.5 μs

15 Byte 15 x 16 μs - 1.5 μs = 238.5 μs

FIFO THRESHOLD MAXIMUM DELAY UNTIL SERVICING AT 1M BPS

Data Rate

1 Byte 1 x 8 μs - 1.5 μs = 6.5 μs

- 116 -

W83627EHF/EF

W83627EHG/EG

2 Byte 2 x 8 μs - 1.5 μs = 14.5 μs

8 Byte 8 x 8 μs - 1.5 μs = 62.5 μs

15 Byte 15 x 8 μs - 1.5 μs = 118.5 μs

At the start of a command, the FIFO is always disabled, and command parameters must be sent based

upon the RQM and DIO bit settings in the Main Status Register. When the FDC enters the command

execution phase, it clears the FIFO off any data to ensure that invalid data are not transferred.

An overrun or underrun terminates the current command and data transfer. Disk writes complete the

current sector by generating a 00 pattern and valid CRC. Reads require the host to remove the

remaining data so that the result phase may be entered.

DMA transfers are enabled by the specify command and are initiated by the FDC when the LDRQ pin is

activated during a data transfer command.

8.1.2 Data Separator

The function of the data separator is to lock onto incoming serial read data. When a lock is achieved,

the serial front-end logic in the chip is provided with a clock that is synchronized with the read data. The

synchronized clock, called the Data Window, is used to internally sample the serial data portion of the

bit cell, and the alternate state samples the clock portion. Serial-to-parallel conversion logic separates

the read data into clock and data bytes.

The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking.

The control logic generates RDD and RWD for every pulse input, and any data pulse input is

synchronized and then adjusted immediately by error adjustment. A digital integrator keeps track of the

speed changes in the input data stream.

8.1.3 Write Precompensation

The write precompensation logic minimizes bit shifts in the RDDATA stream from the disk drive.

Shifting of bits is a known phenomenon in magnetic media and depends on the disk media and the

floppy drive.

The FDC monitors the bit stream that is being sent to the drive. The data patterns that require

precompensation are well known, so, depending on the pattern, the bit is shifted either early or late,

relative to the surrounding bits.

8.1.4 Perpendicular Recording Mode

Publication Release Date: April 7 , 2009

-117- Version 1.94

W83627EHF/EF

W83627EHG

The FDC is also capable of interfacing directly to perpendicular recording floppy drives. Perpendicular

recording differs from the traditional longitudinal method in that the magnetic bits are oriented vertically.

This scheme packs more data bits into the same area.

FDCs with perpendicular recording drives can read standard 3.5" floppy disks and can read and write

perpendicular media. Some manufacturers offer drives that can read and write standard and

perpendicular media in a perpendicular media drive.

A single command puts the FDC into perpendicular mode. All other commands operate as they

normally do. Perpendicular mode requires a 1 Mbps data rate for the FDC, and, at this data rate, the

FIFO manages the host interface bottleneck due to the high speed of data transfer to and from the disk.

FDC Core

The W83627EHF/EHG/EF/EG FDC is capable of performing twenty commands. Each command is

initiated by a multi-byte transfer from the microprocessor, and the result may be a multi-byte transfer

back to the microprocessor. Each command consists of three phases: command, execution, and result.

Command

The microprocessor issues all required information to the controller to perform a specific operation.

Execution

The controller performs the specified operation.

Result

After the operation is completed, status information and other housekeeping information are provided

to the microprocessor.

The next section introduces each of the commands.

8.1.5 FDC Commands

Command Symbol Descriptions:

C: Cylinder Number 0 - 256

D: Data Pattern

DIR: Step Direction

DIR = 0: step out

- 118 -

W83627EHF/EF

W83627EHG/EG

DIR = 1: step in

DS0: Disk Drive Select 0

DS1: Disk Drive Select 1

DTL: Data Length

EC: Enable Count

EFIFO: Enable FIFO

EIS: Enable Implied Seek

EOT: End of Track

FIFOTHR: FIFO Threshold

GAP: Gap Length Selection

GPL: Gap Length

H: Head Number

HDS: Head Number Select

HLT: Head Load Time

HUT: Head Unload Time

LOCK: Lock EFIFO, FIFOTHR, and PTRTRK bits to prevent being affected by software reset

MFM: MFM or FM Mode

MT: Multitrack

N: The number of data bytes written in a sector

NCN: New Cylinder Number

ND: Non-DMA Mode

OW: Overwritten

PCN: Present Cylinder Number

POLL: Polling Disable

PRETRK: Precompensation Start Track Number

R: Record

RCN: Relative Cylinder Number

R/W: Read/Write

SC: Sectors per Cylinder

SK: Skip deleted data address mark

SRT: Step Rate Time

Publication Release Date: April 7 , 2009

-119- Version 1.94

W83627EHF/EF

W83627EHG

ST0: Status Register 0

ST1: Status Register 1

ST2: Status Register 2

ST3: Status Register 3

WG: Write gate alters timing of WE

(1) Read Data

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W MT MFM SK 0 0

1 1 0

Command codes

W 0 0 0 0 0

HDS DS1 DS0

---------------------- C ------------------------

---------------------- H ------------------------

Sector ID information prior

to command execution

---------------------- R ------------------------

---------------------- N ------------------------

-------------------- EOT -----------------------

-------------------- GPL -----------------------

W -------------------- DTL -----------------------

Execution Data transfer between the

FDD and system

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Sector ID information after

command execution

- 120 -

W83627EHF/EF

W83627EHG/EG

(2) Read Deleted Data

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W MT MFM SK 0 1 1

0 0

Command codes

W 0 0 0 0 0

HDS DS1 DS0

---------------------- C ------------------------

---------------------- H ------------------------

Sector ID information prior

to command execution

---------------------- R ------------------------

---------------------- N ------------------------

-------------------- EOT -----------------------

-------------------- GPL -----------------------

W -------------------- DTL -----------------------

Execution Data transfer between the

FDD and system

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Sector ID information after

command execution

Publication Release Date: April 7 , 2009

-121- Version 1.94

W83627EHF/EF

W83627EHG

(3) Read A Track

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 MFM 0 0 0

0 1 0

Command codes

W 0 0 0 0 0

HDS DS1 DS0

---------------------- C ------------------------

---------------------- H ------------------------

Sector ID information prior

to command execution

---------------------- R ------------------------

---------------------- N ------------------------

-------------------- EOT -----------------------

-------------------- GPL -----------------------

W -------------------- DTL -----------------------

Execution

Data transfer between the

FDD and system; FDD

reads contents of all

cylinders from index hole to

EOT

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Sector ID information after

command execution

(4) Read ID

- 122 -

W83627EHF/EF

W83627EHG/EG

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 MFM 0 0 1

0 1 0

Command codes

W 0 0 0 0 0

HDS DS1 DS0

Execution

The first correct ID

information on the cylinder

is stored in the Data

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Disk status after the

command has been

completed

Publication Release Date: April 7 , 2009

-123- Version 1.94

W83627EHF/EF

W83627EHG

(5) Verify

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W MT MFM SK 1 0 1

1 0

Command codes

W EC 0 0 0 0

HDS DS1 DS0

---------------------- C ------------------------

---------------------- H ------------------------

Sector ID information prior

to command execution

---------------------- R ------------------------

---------------------- N ------------------------

-------------------- EOT -----------------------

-------------------- GPL -----------------------

-------------------- DTL/SC -------------------

Execution No data transfer takes

place

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Sector ID information after

command execution

(6) Version

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 1 0

0 0 0

Command code

- 124 -

W83627EHF/EF

W83627EHG/EG

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Result R 1 0 0 1 0

0 0 0

Enhanced controller

(7) Write Data

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W MT MFM 0 0 0

1 0 1

Command codes

W 0 0 0 0 0

HDS DS1 DS0

---------------------- C ------------------------

---------------------- H ------------------------

Sector ID information prior

to Command execution

---------------------- R ------------------------

---------------------- N ------------------------

-------------------- EOT -----------------------

-------------------- GPL -----------------------

W -------------------- DTL -----------------------

Execution Data transfer between the

FDD and the system

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

Command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Sector ID information after

Command execution

Publication Release Date: April 7 , 2009

-125- Version 1.94

W83627EHF/EF

W83627EHG

(8) Write Deleted Data

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W MT MFM 0 0 1

0 0 1

Command codes

W 0 0 0 0 0

HDS DS1 DS0

---------------------- C ------------------------

---------------------- H ------------------------

Sector ID information prior

to command execution

---------------------- R ------------------------

---------------------- N ------------------------

-------------------- EOT -----------------------

-------------------- GPL -----------------------

-------------------- DTL -----------------------

Execution Data transfer between the

FDD and the system

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Sector ID information after

command execution

- 126 -

W83627EHF/EF

W83627EHG/EG

(9) Format A Track

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 MFM 0 0 1

1 0 1

Command codes

W 0 0 0 0 0

HDS DS1 DS0

---------------------- N ------------------------

--------------------- SC -----------------------

Bytes per Sector

Sectors per Cylinder

--------------------- GPL ---------------------

---------------------- D ------------------------

Gap 3

Filler Byte

Execution

for Each

Sector:

(Repeat)

---------------------- C ------------------------

---------------------- H ------------------------

---------------------- R ------------------------

---------------------- N ------------------------

Input Sector Parameters

Result R

-------------------- ST0 -----------------------

-------------------- ST1 -----------------------

-------------------- ST2 -----------------------

Status information after

command execution

---------------- Undefined -------------------

(10) Recalibrate

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 0 0

1 1 1

Command codes

Publication Release Date: April 7 , 2009

-127- Version 1.94

W83627EHF/EF

W83627EHG

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

W 0 0 0 0 0

0 DS1 DS0

Execution Head retracted to Track 0

Interrupt

(11) Sense Interrupt Status

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 0 1

0 0 0

Command code

Result

---------------- ST0 -------------------------

---------------- PCN -------------------------

Status information at the end

of each seek operation

(12) Specify

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 0 0

0 1 1

Command codes

| ---------SRT ----------- | --------- HUT ---------- |

|------------ HLT ----------------------------------| ND

(13) Seek

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 0 1

1 1 1

Command codes

- 128 -

W83627EHF/EF

W83627EHG/EG

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

0 0 0 0 0

HDS DS1 DS0

-------------------- NCN -----------------------

Execution R Head positioned over proper

cylinder on the diskette

(14) Configure

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 1 0

0 1 1

Configure information

0 0 0 0 0

0 0 0

0 EIS EFIFO POLL | ------ FIFOTHR

----|

| --------------------PRETRK ----------------------- |

Execution Internal registers written

(15) Relative Seek

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 1 DIR 0 0 1

1 1 1

Command codes

0 0 0 0 0

HDS DS1 DS0

| -------------------- RCN ---------------------------- |

(16) Dumpreg

Publication Release Date: April 7 , 2009

-129- Version 1.94

W83627EHF/EF

W83627EHG

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 0 1

1 1 0

Registers placed in FIFO

Result

----------------------- PCN-Drive 0--------------------

----------------------- PCN-Drive 1 -------------------

----------------------- PCN-Drive 2--------------------

----------------------- PCN-Drive 3 -------------------

--------SRT ------------------ | --------- HUT --------

----------- HLT -----------------------------------| ND

------------------------ SC/EOT ----------------------

LOCK 0 D3 D2 D1 D0 GAP

0 EIS EFIFO POLL | ------ FIFOTHR --------

-----------------------PRETRK -------------------------

(17) Perpendicular Mode

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 1 0

0 1 0

Command Code

W OW 0 D3 D2 D1 D0

GAP WG

- 130 -

W83627EHF/EF

W83627EHG/EG

(18) Lock

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W LOCK 0 0 1 0

1 0 0

Command Code

Result R 0 0 0 LOCK 0

0 0 0

(19) Sense Drive Status

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W 0 0 0 0 0

1 0 0

Command Code

W 0 0 0 0 0

HDS DS1 DS0

Result

---------------- ST3 ------------------------- Status information about

the disk drive

(20) Invalid

PHASE R/W D7 D6 D5 D4 D3 D2

D1 D0

REMARKS

Command W ------------- Invalid Codes ----------------- Invalid codes (no operation-

FDC goes to standby state)

Result R -------------------- ST0 ---------------------- ST0 = 80h

Publication Release Date: April 7 , 2009

-131- Version 1.94

W83627EHF/EF

W83627EHG

8.2 Register Descriptions

There are several status, data, and control registers in the W83627EHF/EHG/EF/EG. These registers

are defined below, and the rest of this section provides more details about each one of them.

ADDRESS REGISTER

OFFSET READ WRITE

base address + 0

base address + 1

base address + 2

base address + 3

SA REGISTER

SB REGISTER

TD REGISTER

DO REGISTER

TD REGISTER

base address + 4 MS REGISTER DR REGISTER

base address + 5 DT (FIFO) REGISTER DT (FIFO) REGISTER

base address + 7 DI REGISTER CC REGISTER

8.2.1 Status Register A (SA Register) (Re ad base address + 0)

Along with the SB register, the SA register is used to monitor several disk-interface pins in PS/2 and

Model 30 modes. In PS/2 mode, the bit definitions for this register are as follows:

34567 0

WP#

INDEX#

HEAD

TRAK0#

STEP

DRV2#

INIT PENDING

DIR

INIT PENDING (Bit 7):

This bit indicates the value of the floppy disk interrupt output.

RESERVED (Bit 6)

STEP (Bit 5):

- 132 -

W83627EHF/EF

W83627EHG/EG

This bit indicates the complement of the STEP# output.

TRAK0#(Bit 4):

This bit indicates the value of the TRAK0# input.

HEAD (Bit 3):

This bit indicates the complement of the HEAD# output.

0 side 0

1 side 1

INDEX#(Bit 2):

This bit indicates the value of the INDEX# output.

WP#(Bit 1):

0 disk is write-protected

1 disk is not write-protected

DIR (Bit 0)

This bit indicates the direction of head movement.

0 outward direction

1 inward direction

In PS/2 Model 30 mode, the bit definitions for this register are as follows:

34567 0

INDEX

HEAD#

TRAK0

STEP F/F

DRQ

INIT PENDING

DIR#

INIT PENDING (Bit 7):

This bit indicates the value of the floppy disk interrupt output.

Publication Release Date: April 7 , 2009

-133- Version 1.94

W83627EHF/EF

W83627EHG

DRQ (Bit 6):

This bit indicates the value of the DRQ output pin.

STEP F/F (Bit 5):

This bit indicates the complement of the latched STEP# output.

TRAK0 (Bit 4):

This bit indicates the complement of the TRAK0# input.

HEAD# (Bit 3):

This bit indicates the value of the HEAD# output.

0 side 1

1 side 0

INDEX (Bit 2):

This bit indicates the complement of the INDEX# output.

WP (Bit 1):

0 disk is not write-protected

1 disk is write-protected

DIR# (Bit 0)

This bit indicates the direction of head movement.

0 inward direction

1 outward direction

8.2.2 Status Register B (SB Register) (Re ad base address + 1)

Along with the SA register, the SB register is used to monitor several disk interface pins in PS/2 and

Model 30 modes. In PS/2 mode, the bit definitions for this register are as follows:

- 134 -

W83627EHF/EF

W83627EHG/EG

1 1

MOT EN

RDATA Toggle

WDATA Toggle

Drive SEL0

Reserved

345 6 7 0

Drive SEL0 (Bit 5):

This bit indicates the status of the DO REGISTER, bit 0 (drive-select bit 0).

WDATA Toggle (Bit 4):

This bit changes state on every rising edge of the WD# output pin.

RDATA Toggle (Bit 3):

This bit changes state on every rising edge of the RDATA# output pin.

WE (Bit 2):

This bit indicates the complement of the WE# output pin.

RESERVED (Bit 1)

MOT EN A (Bit 0)

This bit indicates the complement of the MOA# output pin.

In PS/2 Model 30 mode, the bit definitions for this register are as follows:

34567 0

DSC#

Reserved

WE F/F

RDATA F/F

DSA#

Reserved

WD F/F

34567 0

DSC#

Reserved

WE F/F

RDATA F/F

DSA#

Reserved

WD F/F

Publication Release Date: April 7 , 2009

-135- Version 1.94

W83627EHF/EF

W83627EHG

RESERVED (Bit 7)

RESERVED (Bit 6)

DSA# (Bit 5):

This bit indicates the status of the DSA# output pin.

WD F/F (Bit 4):

This bit indicates the complement of the WD# output pin, which is latched on every rising edge of the

WD# output pin.

RDATA F/F (Bit 3):

This bit indicates the complement of the latched RDATA# output pin.

WE F/F (Bit 2):

This bit indicates the complement of the latched WE# output pin.

RESERVED (Bit 1)

RESERVED (Bit 0)

8.2.3 Digital Output Register (DO Register) (Write base address + 2)

The Digital Output Register is a write-only register that controls drive motors, drive selection, DRQ/IRQ

enable, and FDC reset. The bit definitions are as follows:

- 136 -

W83627EHF/EF

W83627EHG/EG

7654

321-0

Drive Select: 00 select drive A

01 Reserved

10 Reserved

11 Reserved

Floppy Disk Controller Reset

Active low resets FDC

DMA and INT Enable

Active high enable DRQ/IRQ

Motor Enable A. Motor A on when active high

Reserved

8.2.4 Tape Drive Register (TD Register) (Read base address + 3 )

This register is used to assign a particular drive number to the tape drive support mode of the data

separator. This register also holds the media ID, drive type, and floppy boot drive information for the

floppy disk drive.

In normal floppy mode, this register only has bits 0 and 1, and the bit definitions are as follows:

34567 0

Tape sel 0

Tape sel 1

XX XX X X

If the three-mode FDD function is enabled (EN3MODE = 1 in LD0 CRF0, Bit 0), the bit definitions are

as follows:

34567 0

Floppy boot drive

Floppy boot drive 1

Drive type ID0

Drive type ID1

Media ID0

Media ID1

Tape Sel 0

Tape Sel 1

Media ID1 Media ID0 (Bit 7, 6):

These two bits are read-only. These two bits reflect the value of LD0 CRF1, bits 5 and 4.

Publication Release Date: April 7 , 2009

-137- Version 1.94

W83627EHF/EF

W83627EHG

Drive type ID1 Drive type ID0 (Bit 5, 4):

These two bits reflect two of the bits in LD0 CRF2. Which two bits are reflected depends on the last

drive selection in the DO register.

Floppy Boot drive 1, 0 (Bit 3, 2):

These two bits reflect the value of LD0 CRF1, bits 7 and 6.

Tape Sel 1, Tape Sel 0 (Bit 1, 0):

These two bits assign a logical drive number to the tape drive. Drive 0 is not available as a tape drive

and is reserved for the floppy disk boot drive.

TAPE SEL 1 TAPE SEL 0 DRIVE SELECTED

0 0 None

0 1 1

1 0 2

1 1 3

8.2.5 Main Status Register (MS Register) (Read base address + 4)

The Main Status Register is used to control the flow of data between the microprocessor and the

controller. The bit definitions for this register are as follows:

FDD 0 Busy, (D0B = 1), FDD number 0 is in the SEEK mode.

Reserved.

FDC Busy, (CB). A read or write command is in the process when CB = HIGH.

Non-DMA mode, the FDC is in the non-DMA mode, this bit is set only during the

execution phase in non-DMA mode.

Transition to LOW state indicates execution phase has ended.

DATA INPUT/OUTPUT, (DIO). If DIO= HIGH then transfer is from Data Register to the processor.

If DIO = LOW then transfer is from processor to Data Register.

Request for Master (RQM). A high on this bit indicates Data Register

is ready to send or receive data to or from the processor.

7654321 0

Reserved.

8.2.6 Data Rate Register (DR Register) (Write base address + 4)

- 138 -

W83627EHF/EF

W83627EHG/EG

The Data Rate Register is used to set the transfer rate and write precompensation. However, in PC-AT

and PS/2 Model 30 and PS/2 modes, the data rate is controlled by the CC register, not by the DR

34567 0

DRATE0

DRATE1

PRECOMP0

PRECOMP1

PRECOMP2

POWER DOWN

S/W RESET

S/W RESET (Bit 7):

This bit is the software reset bit.

POWER-DOWN (Bit 6):

0 FDC in normal mode

1 FDC in power-down mode

PRECOMP2 PRECOMP1 PRECOMP0 (Bit 4, 3, 2):

These three bits select the value of write precompensation. The following tables show the

precompensation values for every combination of these bits.

PRECOMP PRECOMPENSATION DELAY

2 1 0 250K - 1 Mbps 2 Mbps Tape drive

0 0 0 Default Delays Default Delays

0 0 1 41.67 ns 20.8 ns

0 1 0 83.34 ns 41.17 ns

0 1 1 125.00 ns 62.5ns

1 0 0 166.67 ns 83.3 ns

1 0 1 208.33 ns 104.2 ns

Publication Release Date: April 7 , 2009

-139- Version 1.94

W83627EHF/EF

W83627EHG

PRECOMP PRECOMPENSATION DELAY

2 1 0 250K - 1 Mbps 2 Mbps Tape drive

1 1 0 250.00 ns 125.00 ns

1 1 1 0.00 ns (disabled) 0.00 ns (disabled)

DATA RATE DEFAULT PRECOMPENSATION DELAYS

250 KB/S 125 ns

300 KB/S 125 ns

500 KB/S 125 ns

1 MB/S 41.67ns

2 MB/S 20.8 ns

DRATE1 DRATE0 (Bit 1, 0):

These two bits select the data rate of the FDC and reduced write-current control.

00 500 KB/S (MFM), 250 KB/S (FM), RWC# = 1

01 300 KB/S (MFM), 150 KB/S (FM), RWC# = 0

10 250 KB/S (MFM), 125 KB/S (FM), RWC# = 0

11 1 MB/S (MFM), Illegal (FM), RWC# = 1

The 2 MB/S data rate for the tape drive is only supported by setting DRATE1 and DRATE0 to 01, as

well as setting DRT1 and DRT0 (CRF4 and CRF5 for logical device 0) to 10. Please see the functional

description of CRF4 or CRF5 and the data rate table for individual data-rate settings.

8.2.7 FIFO Register (R/W base address + 5)

The FIFO register consists of four status registers in a stack, and only one register is presented to the

data bus at a time. The FIFO register stores data, commands, and parameters, and it provides

disk-drive status information. In addition, data bytes pass through the data register to program or obtain

results after a command. In the W83627EHF/EHG/EF/EG, this register is disabled after reset. The

FIFO can enable it and change its values through the configure command.

Status Register 0 (ST0)

- 140 -

W83627EHF/EF

W83627EHG/EG

7-6 5 43 2 1-0

US1, US0 Drive Select:

00 Drive A selected

01 Reserved

10 Reserved

11 Reserved

HD Head address:

1 Head selected

0 Head selected

NR Not Ready:

1 Drive is not ready

0 Drive is ready

EC Equipment Check:

1 When a fault signal is received from the FDD or the track

0 signal fails to occur after 77 step pulses

0 No error

SE Seek end:

1 seek end

0 seek error

IC Interrupt Code:

00 Normal termination of command

01 Abnormal termination of command

10 Invalid command issue

11 Abnormal termination because the ready signal from FDD changed state during command execution

Status Register 1 (ST1)

Missing Address Mark. 1 When the FDC cannot detect the data address mark

or the data address mark has been deleted.

NW (Not Writable). 1 If a write Protect signal is detected from the diskette drive during

execution of write data.

ND (No DATA). 1 If specified sector cannot be found during execution of a read, write or verifly data.

Not used. This bit is always 0.

OR (Over Rum). 1 If the FDC is not serviced by the host system within a certain time interval during data transfer.

DE (data Error).1 When the FDC detects a CRC error in either the ID field or the data field.

Not used. This bit is always 0.

EN (End of track). 1 When the FDC tries to access a sector beyond the final sector of a cylinder.

234567

Status Register 2 (ST2)

234

BC (Bad Cylinder)

MD (Missing Address Mark in Data Field).

1 If the FDC cannot find a data address mark

(or the address mark has been deleted)

when reading data from the media

0 No error

1 Bad Cylinder

0 No error

SN (Scan Not satisfied)

1 During execution of the Scan command

0 No error

SH (Scan Equal Hit)

1 During execution of the Scan command, if the equal condition is satisfied

0 No error

WC (Wrong Cylinder)

1 Indicates wrong Cylinder

DD (Data error in the Data field)

1 If the FDC detects a CRC error in the data field

0 No error

CM (Control Mark)

1 During execution of the read data or scan command

0 No error

Not used. This bit is always 0

Publication Release Date: April 7 , 2009

-141- Version 1.94

W83627EHF/EF

W83627EHG

Status Register 3 (ST3)

US0 Unit Select 0

US1 Unit Select 1

HD Head Address

TS Two-Side

TO Track 0

RY Ready

WP Write Protected

FT Fault

8.2.8 Digital Input Register (DI Register) (Read base address + 7)

The Digital Input Register is an 8-bit, read-only register used for diagnostic purposes. In PC/XT or

PC/AT mode, only bit 7 is checked by the BIOS. When the register is read, bit 7 shows the complement

of DSKCHG#, while the other bits remain in tri-state. The bit definitions are as follows:

xxx

01234

567

Reserved for the hard disk controller

During a read of this register, these bits are in tri-sta

DSKCHG

In PS/2 mode, the bit definitions are as follows:

34567 0

HIGH DENS#

DRATE0

DRATE1

DSKCHG

DSKCHG (Bit 7):

This bit indicates the complement of the DSKCHG# input.

Bit 6-3: These bits are always a logic 1 during a read.

DRATE1 DRATE0 (Bit 2, 1):

These two bits select the data rate of the FDC. See DR register bits 1 and 0 (Data Rate Register (DR

- 142 -

W83627EHF/EF

W83627EHG/EG

HIGHDENS# (Bit 0):

0 500 KB/S or 1 MB/S data rate (high-density FDD)

1 250 KB/S or 300 KB/S data rate

In PS/2 Model 30 mode, the bit definitions are as follows:

34567 0

DRATE0

DRATE1

DSKCHG#

NOPREC

DMAEN

000

DSKCHG (Bit 7):

This bit indicates the status of the DSKCHG# input.

Bit 6-4: These bits are always a logic 0 during a read.

DMAEN (Bit 3):

This bit indicates the value of DO register, bit 3.

NOPREC (Bit 2):

This bit indicates the value of the NOPREC bit in the CC REGISTER.

DRATE1 DRATE0 (Bit 1, 0):

These two bits select the data rate of the FDC. See DR register bits 1 and 0 (Data Rate Register (DR

8.2.9 Configuration Control Register (CC Register) (Write base address + 7)

This register is used to control the data rate. In PC/AT and PS/2 mode, the bit definitions are as follows:

Publication Release Date: April 7 , 2009

-143- Version 1.94

W83627EHF/EF

W83627EHG

xxxx xx

DRATE0

DRATE1

X: Reserved

Bit 7-2: Reserved. These bits should be set to 0.

DRATE1 DRATE0 (Bit 1, 0):

These two bits select the data rate of the FDC. See DR register bits 1 and 0 (Data Rate Register (DR

In the PS/2 Model 30 mode, the bit definitions are as follows:

34567 0

DRATE0

DRATE1

NOPREC

XX XX X

X: Reserved

Bit 7-3: Reserved. These bits should be set to 0.

NOPREC (Bit 2):

This bit disables the precompensation function. It can be set by the software.

DRATE1 DRATE0 (Bit 1, 0):

These two bits select the data rate of the FDC. See DR register bits 1 and 0 (Data Rate Register (DR

- 144 -

W83627EHF/EF

W83627EHG/EG

9. UART PORT

9.1 Universal Asynchronous Receiver/Transmitter (UART A, UART B)

The UARTs are used to convert parallel data into serial format for transmission and to convert serial

data into parallel format during reception. The serial data format is a start bit, followed by five to eight

data bits, a parity bit (if programmed) and one, one-and-a-half (five-bit format only) or two stop bits.

The UARTs are capable of handling divisors of 1 to 65535 and producing a 16x clock for driving the

internal transmitter logic. Provisions are also included to use this 16x clock to drive the receiver logic.

The UARTs also support the MIDI data rate. Furthermore, the UARTs also include a complete

modem control capability and 16-byte FIFOs for reception and transmission to reduce the number of

interrupts presented to the CPU.

9.2 Register Description

9.2.1 UART Control Register (UCR) (Read/Write)

The UART Control Register defines and controls the protocol for asynchronous data communication,

including data length, stop bit, parity, and baud rate selection.

Data length select bit 0 (DLS0)

Data length select bit 1(DLS1)

Multiple stop bits enable (MSBE)

Parity bit enable (PBE)

Even parity enable (EPE)

Parity bit fixed enable (PBFE)

Set silence enable (SSE)

Baudrate divisor latch access bit (BDLAB)

Bit 7: BDLAB. When this bit is set to logical 1, designers can access the divisor (in 16-bit binary format)

from the divisor latches of the baud-rate generator during a read or write operation. When this bit

is set to logical 0, the Receiver Buffer Register, the Transmitter Buffer Register, and the Interrupt

Control Register can be accessed.

Bit 6: SSE. A logical 1 forces the Serial Output (SOUT) to a silent state (a logical 0). Only IRTX is

affected by this bit; the transmitter is not affected.

Bit 5: PBFE. When PBE and PBFE of UCR are both set to logical 1,

(1) if EPE is logical 1, the parity bit is fixed as logical 0 when transmitting and checking.

Publication Release Date: April 7 , 2009

-145- Version 1.94

W83627EHF/EF

W83627EHG

(2) if EPE is logical 0, the parity bit is fixed as logical 1 when transmitting and checking.

Bit 4: EPE. When PBE is set to logical 1, this bit counts the number of logical 1's in the data word bits

and determines the parity bit. When this bit is set to logical 1, the parity bit is set to logical 1 if an

even number of logical 1's are sent or checked. When the bit is set to logical 0, the parity bit is

logical 1 if an odd number of logic 1's are sent or checked.

Bit 3: PBE. When this bit is set to logical 1, the transmitter inserts a stop bit between the last data bit

and the stop bit of the SOUT, and the receiver checks the parity bit in the same position.

Bit 2: MSBE. This bit defines the number of stop bits in each serial character that is transmitted or

received.

(1) If MSBE is set to logical 0, one stop bit is sent and checked.

(2) If MSBE is set to logical 1 and the data length is 5 bits, one-and-a-half stop bits are sent and

checked.

(3) If MSBE is set to logical 1 and the data length is 6, 7, or 8 bits, two stop bits are sent and

checked.

Bits 0 and 1: DLS0, DLS1. These two bits define the number of data bits that are sent or checked in

each serial character.

DLS1 DLS0 DATA LENGTH

0 0 5 bits

0 1 6 bits

1 0 7 bits

1 1 8 bits

The following table identifies the remaining UART registers. Each one is described separately in the

following sections.

- 146 -

W83627EHF/EF

W83627EHG/EG

Bit Number

+ 0

BDLAB = 0

Receiver

Buffer

(Read Only)

RBR RX Data

Bit 0

RX Data

Bit 1

RX Data

Bit 2

RX Data

Bit 3

RX Data

Bit 4

RX Data

Bit 5

RX Data

Bit 6

RX Data

Bit 7

+ 0

BDLAB = 0

Transmitter

Buffer Register

(Write Only)

TBR TX Data

Bit 0

TX Data

Bit 1

TX Data

Bit 2

TX Data

Bit 3

TX Data

Bit 4

TX Data

Bit 5

TX Data

Bit 6

TX Data

Bit 7

+ 1

BDLAB = 0

Interrupt Control

ICR RBR Data

Ready

Interrupt

Enable

(ERDRI)

TBR

Empty

Interrupt

Enable

(ETBREI)

USR

Interrupt

Enable

(EUSRI)

HSR

Interrupt

Enable

(EHSRI)

0 0 0 0

+ 2 Interrupt Status

(Read Only)

ISR "0" if

Interrupt

Pending

Interrupt

Status

Bit (0)

Interrupt

Status

Bit (1)

Interrupt

Status

Bit (2)**

0 0 FIFOs

Enabled

FIFOs

Enabled

+ 2 UART FIFO

Control

(Write Only)

UFR FIFO

Enable

RCVR

FIFO

Reset

XMIT

FIFO

Reset

DMA

Mode

Select

Reserved Reversed RX

Interrupt

Active Level

(LSB)

Interrupt

Active Level

(MSB)

+ 3 UART Control

UCR Data

Length

Select

Bit 0

(DLS0)

Data

Length

Select

Bit 1

(DLS1)

Multiple

Stop Bits

Enable

(MSBE)

Parity

Bit

Enable

(PBE)

Even

Parity

Enable

(EPE)

Parity

Bit Fixed

Enable

PBFE)

Set

Silence

Enable

(SSE)

Baudrate

Divisor

Latch

Access Bit

(BDLAB)

+ 4 Handshake

Control

HCR Data

Terminal

Ready

(DTR)

Request

Send

(RTS)

Loopback

Input

IRQ

Enable

Internal

Loopback

Enable

0 0 0

Publication Release Date: April 7 , 2009

-147- Version 1.94

W83627EHF/EF

W83627EHG

+ 5 UART Status

USR RBR Data

Ready

(RDR)

Overrun

Error

(OER)

Parity Bit

Error

(PBER)

No Stop

Bit

Error

(NSER)

Silent

Byte

Detected

(SBD)

TBR

Empty

(TBRE)

TSR

Empty

(TSRE)

RX FIFO

Error

Indication

(RFEI) **

+ 6 Handshake

Status Register

HSR CTS

Toggling

(TCTS)

DSR

Toggling

(TDSR)

RI Falling

Edge

(FERI)

DCD

Toggling

(TDCD)

Clear

to Send

(CTS)

Data Set

Ready

(DSR)

Ring

Indicator

(RI)

Data Carrier

Detect

(DCD)

+ 7 User Defined

UDR Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7

+ 0

BDLAB = 1

Baudrate

Divisor Latch

Low

BLL Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7

+ 1

BDLAB = 1

Baudrate

Divisor Latch

High

BHL Bit 8 Bit 9 Bit 10 Bit 11 Bit 12 Bit 13 Bit 14 Bit 15

*: Bit 0 is the least significant bit. The least significant bit is the first bit serially transmitted or received.

**: These bits are always 0 in 16450 Mode.

- 148 -

W83627EHF/EF

W83627EHG/EG

9.2.2 UART Status Register (USR) (Read/Write)

This 8-bit register provides information about the status of data transfer during communication.

670

RBR Data ready (RDR)

Overrun error (OER)

Parity bit error (PBER)

No stop bit error (NSER)

Silent byte detected (SBD)

Transmitter Buffer Register empty (TBRE)

Transmitter Shift Register empty (TSRE)

RX FIFO Error Indication (RFEI)

Bit 7: RFEI. In 16450 mode, this bit is always set to logical 0. In 16550 mode, this bit is set to logical 1

when there is at least one parity-bit error and no stop-bit error or silent-byte detected in the FIFO.

In 16550 mode, this bit is cleared to logical 0 by reading from the USR if there are no remaining

errors left in the FIFO.

Bit 6: TSRE. In 16450 mode, this bit is set to logical 1 when TBR and TSR are both empty. In 16550

mode, it is set to logical 1 when the transmit FIFO and TSR are both empty. Otherwise, this bit is

set to logical 0.

Bit 5: TBRE. In 16450 mode, when a data character is transferred from TBR to TSR, this bit is set to

logical 1. If ETREI of ICR is high, an interrupt is generated to notify the CPU to write the next

data. In 16550 mode, this bit is set to logical 1 when the transmit FIFO is empty. It is set to logical

0 when the CPU writes data into TBR or the FIFO.

Bit 4: SBD. This bit is set to logical 1 to indicate that received data are kept in silent state for the time it

takes to receive a full word, which includes the start bit, data bits, parity bit, and stop bits. In

16550 mode, it indicates the same condition for the data on the top of the FIFO. When the CPU

reads USR, it sets this bit to logical 0.

Bit 3: NSER. This bit is set to logical 1 to indicate that the received data have no stop bit. In 16550

mode, it indicates the same condition for the data on the top of the FIFO. When the CPU reads

USR, it sets this bit to logical 0.

Bit 2: PBER. This bit is set to logical 1 to indicate that the received data has the wrong parity bit. In

16550 mode, it indicates the same condition for the data on the top of the FIFO. When the CPU

reads USR, it sets this bit to logical 0.

Publication Release Date: April 7 , 2009

-149- Version 1.94

W83627EHF/EF

W83627EHG

Bit 1: OER. This bit is set to logical 1 to indicate that the received data have been overwritten by the

next received data before they were read by the CPU. In 16550 mode, it indicates the same

condition, instead of FIFO full. When the CPU reads USR, it sets this bit to logical 0.

Bit 0: RDR. This bit is set to logical 1 to indicate that the received data are ready to be read by the CPU

in the RBR or FIFO. When no data are left in the RBR or FIFO, the bit is set to logical 0.

9.2.3 Handshake Control Register (HCR) (Read/Write)

This register controls pins used with handshaking peripherals such as modems and also controls the

diagnostic mode of the UART.

00 0

345

Data terminal ready (DTR)

Request to send (RTS)

Loopback RI input

IRQ enable

Internal loopback enable

Bit 4: When this bit is set to logical 1, the UART enters diagnostic mode, as follows:

(1) SOUT is forced to logical 1, and SIN is isolated from the communication link.

(2) The modem output pins are set to their inactive state.

(3) The modem input pins are isolated from the communication link and connect internally as

DTR (bit 0 of HCR)→DSR#, RTS (bit 1 of HCR) →CTS#, Loopback RI input (bit 2 of HCR) → RI# and

IRQ enable (bit 3 of HCR) →DCD#.

Aside from the above connections, the UART operates normally. This method allows the CPU to

test the UART in a convenient way.

Bit 3: The UART interrupt output is enabled by setting this bit to logical 1. In diagnostic mode, this bit is

internally connected to the modem control input DCD#.

Bit 2: This bit is only used in the diagnostic mode. In diagnostic mode, this bit is internally connected to

the modem control input RI#.

Bit 1: This bit controls the RTS# output. The value of this bit is inverted and output to RTS#.

Bit 0: This bit controls the DTR# output. The value of this bit is inverted and output to DTR#.

- 150 -

W83627EHF/EF

W83627EHG/EG

9.2.4 Handshake Status Register (HSR) (Read/Write)

This register reflects the current state of the four input pins used with handshake peripherals such as

modems and records changes on these pins.

12345670

RI falling edge (FERI)

Clear to send (CTS)

Data set ready (DSR)

Ring indicator (RI)

Data carrier detect (DCD)

CTS#

toggling (TCTS)

DSR#

toggling (TDSR)

DCD#

toggling (TDCD)

Bit 7: This bit is the opposite of the DCD# input. This bit is equivalent to bit 3 of HCR in loopback mode.

Bit 6: This bit is the opposite of the RI # input. This bit is equivalent to bit 2 of HCR in loopback mode.

Bit 5: This bit is the opposite of the DSR# input. This bit is equivalent to bit 0 of HCR in loopback mode.

Bit 4: This bit is the opposite of the CTS# input. This bit is equivalent to bit 1 of HCR in loopback mode.

Bit 3: TDCD. This bit indicates that the DCD# pin has changed state after HSR was read by the CPU.

Bit 2: FERI. This bit indicates that the RI # pin has changed from low to high after HSR was read by

the CPU.

Bit 1: TDSR. This bit indicates that the DSR# pin has changed state after HSR was read by the CPU.

Bit 0: TCTS. This bit indicates that the CTS# pin has changed state after HSR was read by the CPU.

Publication Release Date: April 7 , 2009

-151- Version 1.94

W83627EHF/EF

W83627EHG

9.2.5 UART FIFO Control Register (UFR) (Write only)

This register is used to control the FIFO functions of the UART.

345670

FIFO enable

Receiver FIFO reset

Transmitter FIFO reset

DMA mode select

Reserved

RX interrupt active level (LSB)

RX interrupt active level (MSB)

Bit 6, 7: These two bits are used to set the active level of the receiver FIFO interrupt. The active level is

the number of bytes that must be in the receiver FIFO to generate an interrupt.

BIT 7 BIT 6 RX FIFO INTERRUPT ACTIVE LEVEL (BYTES)

0 0 01

0 1 04

1 0 08

1 1 14

Bit 4, 5: Reserved

Bit 3: When this bit is set to logical 1, DMA mode changes from mode 0 to mode 1 if UFR bit 0 = 1.

Bit 2: Setting this bit to logical 1 resets the TX FIFO counter logic to its initial state. This bit is

automatically cleared afterwards.

Bit 1: Setting this bit to logical 1 resets the RX FIFO counter logic to its initial state. This bit is

automatically cleared afterwards.

Bit 0: This bit enables 16550 (FIFO) mode. This bit should be set to logical 1 before the other UFR bits

are programmed.

9.2.6 Interrupt Status Register (ISR) (Read only)

This register reflects the UART interrupt status.

- 152 -

W83627EHF/EF

W83627EHG/EG

1234567 0

0 if interrupt pending

Interrupt Status bit 0

Interrupt Status bit 1

Interrupt Status bit 2

FIFOs enabled

Bit 7, 6: These two bits are set to logical 1 when UFR, bit 0 = 1.

Bit 5, 4: These two bits are always logical 0.

Bit 3: In 16450 mode, this bit is logical 0. In 16550 mode, bits 3 and 2 are set to logical 1 when a

time-out interrupt is pending. See the table below.

Bit 2, 1: These two bits identify the priority level of the pending interrupt, as shown in the table below.

Bit 0: This bit is logical 1 if there is no interrupt pending. If one of the interrupt sources has occurred,

this bit is set to logical 0.

ISR INTERRUPT SET AND FUNCTION

Bit

Interrupt

priority

Interrupt Type

Interrupt Source

Clear Interrupt

0 0 0 1 - - No Interrupt pending -

0 1 1 0 First UART Receive

Status

1. OER = 1 2. PBER =1

3. NSER = 1 4. SBD = 1

Read USR

0 1 0 0 Second RBR Data Ready 1. RBR data ready

2. FIFO interrupt active level

reached

1. Read RBR

2. Read RBR until FIFO

data under active level

1 1 0 0 Second FIFO Data Timeout Data present in RX FIFO for 4

characters period of time since last

access of RX FIFO.

Read RBR

0 0 1 0 Third TBR Empty TBR empty 1. Write data into TBR

2. Read ISR (if priority is

third)

Publication Release Date: April 7 , 2009

-153- Version 1.94

W83627EHF/EF

W83627EHG

ISR INTERRUPT SET AND FUNCTION

Bit

Interrupt

priority

Interrupt Type

Interrupt Source

Clear Interrupt

0 0 0 0 Fourth Handshake status 1. TCTS = 1 2. TDSR = 1

3. FERI = 1 4. TDCD = 1

Read HSR

** Bit 3 of ISR is enabled when bit 0 of UFR is logical 1.

9.2.7 Interrupt Control Register (ICR) (Read/Write)

This 8-bit register enables and disables the five types of controller interrupts separately. A selected

interrupt can be enabled by setting the appropriate bit to logical 1. The interrupt system can be totally

disabled by setting bits 0 through 3 to logical 0.

000

RBR data ready interrupt enable (ERDRI)

TBR empty interrupt enable (ETBREI)

UART receive status interrupt enable (EUSRI)

Handshake status interrupt enable (EHSRI)

Bit 7-4: These four bits are always logical 0.

Bit 3: EHSRI. Set this bit to logical 1 to enable the handshake status register interrupt.

Bit 2: EUSRI. Set this bit to logical 1 to enable the UART status register interrupt.

Bit 1: ETBREI. Set this bit to logical 1 to enable the TBR empty interrupt.

Bit 0: ERDRI. Set this bit to logic 1 to enable the RBR data ready interrupt.

- 154 -

W83627EHF/EF

W83627EHG/EG

9.2.8 Programmable Baud Generator (BLL/BHL) (Read/Write)

Two 8-bit registers, BLL and BHL, compose a programmable baud generator that uses 24 MHz to

generate a 1.8461 MHz frequency and divide it by a divisor from 1 to (216 –1). The output frequency of

the baud generator is the baud rate multiplied by 16, and this is the base frequency for the transmitter

and receiver. The table below illustrates the use of the baud generator with a frequency of 1.8461

MHz. In high-speed UART mode (CR0C, bits 7 and 6), the programmable baud generator directly uses

24 MHz and the same divisor as the normal speed divisor. As a result, in high-speed mode, the data

transmission rate can be as high as 1.5M bps.

BAUD RATE FROM DIFFERENT PRE-DIVIDER

PRE-DIV: 13

1.8461M HZ

PRE-DIV:1.62

14.769M HZ

PRE-DIV:

1.0

24M HZ

DECIMAL DIVISOR

USED TO

GENERATE 16X

CLOCK

ERROR PERCENTAGE

50 400 650 2304 **

75 600 975 1536 **

110 880 1430 1047 0.18%

134.5 1076 1478.5 857 0.099%

150 1200 1950 768 **

300 2400 3900 384 **

600 4800 7800 192 **

1200 9600 15600 96 **

1800 14400 23400 64 **

2000 16000 26000 58 0.53%

2400 19200 31200 48 **

3600 28800 46800 32 **

4800 38400 62400 24 **

7200 57600 93600 16 **

9600 76800 124800 12 **

Publication Release Date: April 7 , 2009

-155- Version 1.94

W83627EHF/EF

W83627EHG

BAUD RATE FROM DIFFERENT PRE-DIVIDER

PRE-DIV: 13

1.8461M HZ

PRE-DIV:1.62

14.769M HZ

PRE-DIV:

1.0

24M HZ

DECIMAL DIVISOR

USED TO

GENERATE 16X

CLOCK

ERROR PERCENTAGE

19200 153600 249600 6 **

38400 307200 499200 3 **

57600 460800 748800 2 **

115200 921600 1497600 1 **

** Unless specified, the error percentage for all of the baud rates is 0.16%.

Note: Pre-Divisor is determined by CRF0 of UART A and B.

9.2.9 User-defined Register (UDR) ( Read/Write)

This is a temporary register that can be accessed and defined by the user.

- 156 -

W83627EHF/EF

W83627EHG/EG

10. PARALLEL PORT

10.1 Printer Interface Logic

The W83627EHF/EHG/EF/EG parallel port can be attached to devices that accept eight bits of parallel

data at standard TTL level. The W83627EHF/EHG/EF/EG supports the IBM XT/AT compatible

parallel port (SPP), the bi-directional parallel port (BPP), the Enhanced Parallel Port (EPP), and the

Extended Capabilities Parallel Port (ECP) on the parallel port.

The following tables show the pin definitions for different modes of the parallel port.

HOST

CONNECTOR

PIN NUMBER

W83627EHF/EHG/

EF/EG

PIN ATTRIBUTE SPP EPP ECP

1 36 O nSTB nWrite

nSTB, HostClk2

2-9 31-26, 24-23 I/O PD<0:7> PD<0:7> PD<0:7>

10 22 I nACK Intr

nACK, PeriphClk2

11 21 I BUSY nWait

BUSY, PeriphAck2

12 19 I PE PE

PEerror, nAckReverse2

13 18 I SLCT Select

SLCT, Xflag2

14 35 O nAFD nDStrb

nAFD, HostAck2

15 34 I nERR nError

nFault1, nPeriphRequest2

16 33 O nINIT nInit

nINIT1, nReverseRqst2

17 32 O nSLIN nAStrb

nSLIN1 , ECPMode2

Notes:

n<name > : Active Low

1. Compatible Mode

2. High Speed Mode

3. For more information, please refer to the IEEE 1284 standard.

Publication Release Date: April 7 , 2009

-157- Version 1.94

W83627EHF/EF

W83627EHG

HOST CONNECTOR PIN NUMBER OF

W83627EHF/EHG/EF/EG

PIN ATTRIBUTE SPP

1 36 O nSTB

2 31 I/O PD0

3 30 I/O PD1

4 29 I/O PD2

5 28 I/O PD3

6 27 I/O PD4

7 26 I/O PD5

8 24 I/O PD6

9 23 I/O PD7

10 22 I nACK

11 21 I BUSY

12 19 I PE

13 18 I SLCT

14 35 O nAFD

15 34 I nERR

16 33 O nINIT

17 32 O nSLIN

10.2 Enhanced Parallel Port (EPP)

The following table lists the registers used in the EPP mode and identifies the bit map of the parallel

port and EPP registers. Some of the registers are used in other modes as well.

A2 A1 A0 REGISTER NOTE

0 0 0 Data port (R/W) 1

0 0 1 Printer status buffer (Read) 1

0 1 0 Printer control latch (Write) 1

- 158 -

W83627EHF/EF

W83627EHG/EG

0 1 0 Printer control swapper (Read) 1

0 1 1 EPP address port (R/W) 2

1 0 0 EPP data port 0 (R/W) 2

1 0 1 EPP data port 1 (R/W) 2

1 1 0 EPP data port 2 (R/W) 2

1 1 1 EPP data port 2 (R/W) 2

Notes:

1. These registers are available in all modes.

2. These registers are available only in EPP mode.

Data Port (R/W) PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

Status Buffer (Read) BUSY# ACK# PE SLCT ERROR# 1 1 TMOUT

Control Swapper (Read) 1 1 1 IRQEN SLIN INIT# AUTOFD# STROBE#

Control Latch (Write) 1 1 DIR IRQ SLIN INIT# AUTOFD# STROBE#

EPP Address Port R/W) PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

EPP Data Port 0 (R/W) PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

EPP Data Port 1 (R/W) PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

EPP Data Port 2 (R/W) PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

EPP Data Port 3 (R/W) PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

Each register (or pair of registers, in some cases) is discussed below.

10.2.1 Data Port (Data Swapper)

The CPU reads the contents of the printer's data latch by reading the data port.

Publication Release Date: April 7 , 2009

-159- Version 1.94

W83627EHF/EF

W83627EHG

10.2.2 Printer Status Buffer

The CPU reads the printer status by reading the printer status buffer. The bit definitions are as follows:

2354670

TMOUT

ERROR#

SLCT

BUSY#

ACK#

Bit 7: This signal is active during data entry, when the printer is off-line during printing, when the print

head is changing position, or in an error state. When this signal is active, the printer is busy and cannot

accept data.

Bit 6: This bit represents the current state of the printer's ACK# signal. A logical 0 means the printer has

received a character and is ready to accept another. Normally, this signal is active for approximately 5

μs before BUSY# stops.

Bit 5: A logical 1 means the printer has detected the end of paper.

Bit 4: A logical 1 means the printer is selected.

Bit 3: A logical 0 means the printer has encountered an error condition.

Bit 1, 2: Reserved. These two bits are always read as logical 1.

Bit 0: This bit is only valid in EPP mode. A logical 1 indicates that a 10-μs time-out has occurred on the

EPP bus; a logical 0 means that no time-out error has occurred. Writing a logical 1 to this bit clears the

time-out status bit; writing a logical 0 has no effect.

10.2.3 Printer Control Latch and Printer Control Swapper

The CPU reads the contents of the printer control latch by reading the printer control swapper. The bit

definitions are as follows:

2345670

STROBE

AUTO FD

SLCT IN

IRQ ENABLE

DIR

INIT#

- 160 -

W83627EHF/EF

W83627EHG/EG

Bit 7, 6: These two bits are always read as logical 1. They can be written.

Bit 5: Direction control bit

When this bit is logical 1, the parallel port is in input mode (read); when it is logical 0, the parallel

port is in output mode (write). This bit can be read and written. In SPP mode, this bit is invalid and

fixed at zero.

Bit 4: A logical 1 allows an interrupt to occur when ACK# changes from low to high.

Bit 3: A logical 1 selects the printer.

Bit 2: A logical 0 starts the printer (50 microsecond pulse, minimum).

Bit 1: A logical 1 causes the printer to line-feed after a line is printed.

Bit 0: A logical 1 generates an active-high pulse for a minimum of 0.5μs to clock data into the printer.

Valid data must be present for a minimum of 0.5μs before and after the strobe pulse.

10.2.4 EPP Address Port

The address port is available only in EPP mode. Bit definitions are as follows:

12345670

PD0

PD1

PD2

PD3

PD5

PD4

PD6

PD7

The contents of DB0-DB7 are buffered (non-inverting) and output to ports PD0-PD7 during a write

operation. The leading edge of IOW# causes an EPP address write cycle to be performed, and the

trailing edge of IOW# latches the data for the duration of the EPP write cycle.

PD0-PD7 ports are read during a read operation. The leading edge of IOR# causes an EPP address

read cycle to be performed and the data to be output to the host CPU.

10.2.5 EPP Data Port 0-3

These four registers are available only in EPP mode. The bit definitions for each data port are the

same and as follows:

Publication Release Date: April 7 , 2009

-161- Version 1.94

W83627EHF/EF

W83627EHG

123456

PD0

PD1

PD2

PD3

PD4

PD5

PD6

PD7

When any EPP data port is accessed, the contents of DB0-DB7 are buffered (non-inverting) and output

to ports PD0-PD7 during a write operation. The leading edge of IOW# causes an EPP data write cycle

to be performed, and the trailing edge of IOW# latches the data for the duration of the EPP write cycle.

During a read operation, ports PD0-PD7 are read, and the leading edge of IOR# causes an EPP read

cycle to be performed and the data to be output to the host CPU.

- 162 -

W83627EHF/EF

W83627EHG/EG

10.2.6 EPP Pin Descriptions

EPP NAME TYPE EPP DESCRIPTION

NWrite O Denotes read or write operation for address or data.

PD<0:7> I/O Bi-directional EPP address and data bus.

Intr I Used by peripheral device to interrupt the host.

NWait I Inactivated to acknowledge that data transfer is complete. Activated to

indicate that the device is ready for the next transfer.

PE I Paper end; same as SPP mode.

Select I Printer-select status; same as SPP mode.

NDStrb O This signal is active low. It denotes a data read or write operation.

Nerror I Error; same as SPP mode.

Ninits O This signal is active low. When it is active, the EPP device is reset to its

initial operating mode.

NAStrb O This signal is active low. It denotes an address read or write operation.

10.2.7 EPP Operation

When EPP mode is selected, the PDx bus is in standard or bi-directional mode when no EPP read,

write, or address cycle is being executed. In this situation, all output signals are set by the SPP Control

Port and the direction is controlled by DIR of the Control Port.

A watchdog timer is required to prevent system lockup. The timer indicates that more than 10 μs have

elapsed from the start of the EPP cycle to the time WAIT# is deasserted. The current EPP cycle is

aborted when a time-out occurs. The time-out condition is indicated in status bit 0.

The EPP operates on a two-phase cycle. First, the host selects the register within the device for

subsequent operations. Second, the host performs a series of read and/or write byte operations to the

selected register. Four operations are supported on the EPP: Address Write, Data Write, Address Read,

and Data Read. All operations on the EPP device are performed asynchronously.

Publication Release Date: April 7 , 2009

-163- Version 1.94

W83627EHF/EF

W83627EHG

10.2.7.1. EPP Version 1.9 Operation

The EPP read/write operation can be completed under the following conditions:

a. If nWait is active low, the read cycle (nWrite inactive high, nDStrb/nAStrb active low) or write cycle

(nWrite active low, nDStrb/nAStrb active low) starts, proceeds normally, and is completed when nWait

goes inactive high.

b. If nWait is inactive high, the read/write cycle cannot start. It must wait until nWait changes to active

low, at which time it starts as described above.

10.2.7.2. EPP Version 1.7 Operation

The EPP read/write cycle can start without checking whether nWait is active or inactive. Once the

read/write cycle starts; however, it does not finish until nWait changes from active low to inactive high.

- 164 -

W83627EHF/EF

W83627EHG/EG

10.3 Extended Capabilities Parallel (ECP) Port

This port is software- and hardware-compatible with existing parallel ports, so the

W83627EHF/EHG/EF/EG parallel port may be used in standard printer mode if ECP is not required. It

provides an automatic high burst-bandwidth channel that supports DMA for ECP in both the forward

(host-to-peripheral) and reverse (peripheral-to-host) directions.

Small FIFOs are used in both forward and reverse directions to improve the maximum bandwidth

requirement. The size of the FIFO is 16 bytes. The ECP port supports an automatic handshake for the

standard parallel port to improve compatibility mode transfer speed.

The ECP port hardware supports run-length-encoded (RLE) decompression. Compression is

accomplished by counting identical bytes and transmitting an RLE byte that indicates how many times

the next byte is to be repeated. RLE compression is required; the hardware support is optional.

For more information about the ECP Protocol, please refer to the Extended Capabilities Port Protocol

and ISA Interface Standard.

The W83627EHF/EHG/EF/EG ECP supports the following modes.

MODE DESCRIPTION

000 SPP mode

001 PS/2 Parallel Port mode

010 Parallel Port Data FIFO mode

011 ECP Parallel Port mode

100 EPP mode (If this option is enabled in the CRF0 to select ECP/EPP mode)

101 Reserved

110 Test mode

111 Configuration mode

The mode selection bits are bits 7-5 of the Extended Control Register.

10.3.1 ECP Register and Bit Map

Publication Release Date: April 7 , 2009

-165- Version 1.94

W83627EHF/EF

W83627EHG

The next two tables list the registers used in the ECP mode and provide a bit map of the parallel port

and ECP registers.

NAME ADDRESS I/O ECP MODES FUNCTION

data Base+000h R/W 000-001 Data Register

ecpAFifo Base+000h R/W 011 ECP FIFO (Address)

dsr Base+001h R All Status Register

dcr Base+002h R/W All Control Register

cFifo Base+400h R/W 010 Parallel Port Data FIFO

ecpDFifo Base+400h R/W 011 ECP FIFO (DATA)

tFifo Base+400h R/W 110 Test FIFO

cnfgA Base+400h R 111 Configuration Register A

cnfgB Base+401h R/W 111 Configuration Register B

ecr Base+402h R/W All Extended Control Register

Note: The base addresses are specified by CR60 and 61, which are determined by the configuration register or the hardware

setting.

D7 D6 D5 D4 D3 D2 D1 D0 NOTE

Data PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0

ecpAFifo Addr/RLE Address or RLE field 2

Dsr nBusy nAck PError Select nFault 1 1 1 1

Dcr 1 1 Directio ackIntEn SelectIn nInit autofd strobe 1

cFifo Parallel Port Data FIFO 2

ecpDFifo ECP Data FIFO 2

tFifo Test FIFO 2

cnfgA 0 0 0 1 0 0 0 0

cnfgB compress intrValue 1 1 1 1 1 1

Ecr MODE nErrIntrEn dmaEn serviceIntr full empty

Notes:

- 166 -

W83627EHF/EF

W83627EHG/EG

1. These registers are available in all modes.

2. All FIFOs use one common 16-byte FIFO.

Each register (or pair of registers, in some cases) is discussed below.

10.3.2 Data and ecpAFifo Port

Modes 000 (SPP) and 001 (PS/2) (Data Port)

During a write operation, the Data Register latches the contents of the data bus on the rising edge of

the input, and the contents of this register are output to PD0-PD7. During a read operation, ports

PD0-PD7 are read and output to the host. The bit definitions are as follows:

7 6 5 4 3 2 1 0

PD0

PD1

PD2

PD3

PD4

PD5

PD6

PD7

Mode 011 (ECP FIFO-Address/RLE)

A data byte written to this address is placed in the FIFO and tagged as an ECP Address/RLE. The

hardware at the ECP port transmits this byte to the peripheral automatically. This operation is defined

only for the forward direction. The bit definitions are as follows:

7 6 5 4 3 2 1 0

Address or

RLE

Address/RLE

Publication Release Date: April 7 , 2009

-167- Version 1.94

W83627EHF/EF

W83627EHG

10.3.3 Device Status Register (DSR)

These bits are logical 0 during a read of the Printer Status Register. The bits of this status register are

defined as follows:

7 6 5 4 3 2 1 0

nFault

Select

PError

nAck

nBusy

111

Bit 7: This bit reflects the complement of the Busy input.

Bit 6: This bit reflects the nAck input.

Bit 5: This bit reflects the PError input.

Bit 4: This bit reflects the Select input.

Bit 3: This bit reflects the nFault input.

Bit 2-0: These three bits are not implemented and are always logical 1 during a read.

10.3.4 Device Control Register (DCR)

The bit definitions are as follows:

7 6 5 4 3 2 1 0

strobe

autofd

nInit

SelectIn

ackIntEn

Direction

- 168 -

W83627EHF/EF

W83627EHG/EG

Bit 7, 6: These two bits are always read as logical one and cannot be written.

Bit 5: If the mode is 000 or 010, this bit has no effect and the direction is always out. In other modes,

0 the parallel port is in output mode.

1 the parallel port is in input mode.

Bit 4: Interrupt request enable. When this bit is set to logical 1, it enables interrupt requests from the

parallel port to the CPU on the low-to-high transition on ACK#.

Bit 3: This bit is inverted and output to the SLIN# output.

0 The printer is not selected.

1 The printer is selected.

Bit 2: This bit is output to the INIT# output.

Bit 1: This bit is inverted and output to the AFD# output.

Bit 0: This bit is inverted and output to the STB# output.

10.3.5 CFIFO (Parallel Port Data FIFO) Mode = 010

This mode is defined only for the forward direction. Bytes written or DMAed to this FIFO are transmitted

by a hardware handshake to the peripheral using the standard parallel port protocol. Transfers to the

FIFO are byte-aligned.

10.3.6 ECPDFIFO (ECP Data FIFO) Mode = 011

When the direction bit is 0, bytes written or DMAed to this FIFO are transmitted by a hardware

handshake to the peripheral using the ECP parallel port protocol. Transfers to the FIFO are

byte-aligned.

When the direction bit is 1, data bytes from the peripheral are read via automatic hardware handshake

from ECP into this FIFO. Reads or DMAs from the FIFO return bytes of ECP data to the system.

10.3.7 TFIFO (Test FIFO Mode) Mode = 110

Data bytes may be read, written, or DMAed to or from the system to this FIFO in any direction. Data in

the tFIFO is not transmitted to the parallel port lines. However, data in the tFIFO may be displayed on

the parallel port data lines.

10.3.8 CNFGA (Configuration Register A) Mode = 111

This register is a read-only register. When it is read, 10h is returned indicating an 8-bit implementation.

10.3.9 CNFGB (Configuration Register B) Mode = 111

Publication Release Date: April 7 , 2009

-169- Version 1.94

W83627EHF/EF

W83627EHG

The bit definitions are as follows:

7 6 5 4 3 2 1 0

1 1 1

intrValue

compress

IRQx 0

IRQx 1

IRQx 2

Bit 7: This bit is read-only. It is logical 0 during a read, which means that this chip does not support

hardware RLE compression.

Bit 6: Returns the value on the ISA IRQ line to determine possible conflicts.

Bit 5-3: Reflects the IRQ resource assigned for ECP port.

CNFGB[5:3] IRQ RESOURCE

000 Reflects other IRQ resources selected by PnP

001 IRQ7

010 IRQ9

011 IRQ10

100 IRQ11

101 IRQ14

110 IRQ15

111 IRQ5

Bit 2-0: These five bits are logical 1 during a read and can be written.

10.3.10 ECR (Extended Control Register) Mode = all

This register controls the extended ECP parallel port functions. The bit definitions are follows:

- 170 -

W83627EHF/EF

W83627EHG/EG

7 6 5 4 3 2 1 0

empty

full

service Int

dmaEn

nErrIntrEn

MODE

Bit 7-5: Read/Write. These bits select the mode.

000 Standard Parallel Port (SPP) mode. The FIFO is reset in this mode.

001 PS/2 Parallel Port mode. In addition to the functions of the SPP mode, this mode has

an extra trait: Direction is able to tri-state the data lines. Furthermore, reading the

data register returns the value on the data lines, not the value in the data register.

010 Parallel Port FIFO mode. This is the same as SPP mode except that bytes are

written or DMAed to the FIFO. FIFO data are automatically transmitted using the

standard parallel port protocol. This mode functions only when direction is 0.

011 ECP Parallel Port Mode. When the direction is 0 (forward direction), bytes placed

into the ecpDFifo and bytes written to the ecpAFifo are placed in a single FIFO and

automatically transmitted to the peripheral using the ECP Protocol. When the

direction is 1 (reverse direction), bytes are moved from the ECP parallel port and

packed into bytes in the ecpDFifo.

100 EPP Mode. EPP mode is activated if the EPP mode is selected.

101 Reserved.

110 Test Mode. The FIFO may be written and read in this mode, but the data is not

transmitted on the parallel port.

111 Configuration Mode. The confgA and confgB registers are accessible at 0x400 and

0x401 in this mode.

Bit 4: Read/Write (Valid only in ECP Mode)

1 Disables the interrupt generated on the asserting edge of nFault.

0 Enables the interrupt generated on the falling edge of nFault. This prevents

interrupts from being lost in the time between the read of the ECR and the write of

the ECR.

Publication Release Date: April 7 , 2009

-171- Version 1.94

W83627EHF/EF

W83627EHG

Bit 3: Read/Write

1 Enables DMA.

0 Disables DMA unconditionally.

Bit 2: Read/Write

1 Disables DMA and all of the service interrupts. Writing a logical 1 to this bit does not

cause an interrupt.

0 Enables one of the following cases of interrupts. When one of the serviced interrupts

occurs, this bit is set to logical 1 by the hardware. This bit must be reset to logical 0

to re-enable the interrupts.

(a) dmaEn = 1: During DMA, this bit is set to logical 1 when terminal count is

reached.

(b) dmaEn = 0, direction = 0: This bit is set to logical 1 whenever there are writeIntr

threshold or more bytes free in the FIFO.

threshold or more valid bytes to be read from the FIFO.

Bit 1: Read only

0 The FIFO has at least one free byte.

1 The FIFO is completely full; it cannot accept another byte.

Bit 0: Read only

0 The FIFO contains at least one byte of data.

1 The FIFO is completely empty.

10.3.11 ECP Pin Descriptions

NAME TYPE DESCRIPTION

NStrobe (HostClk) O This pin loads data or address into the slave on its asserting edge

during write operations. This signal handshakes with Busy.

PD<7:0> I/O These signals contain address, data or RLE data.

- 172 -

W83627EHF/EF

W83627EHG/EG

NAME TYPE DESCRIPTION

nAck (PeriphClk) I This signal indicates valid data driven by the peripheral when

asserted. This signal handshakes with nAutoFd in reverse.

Busy (PeriphAck)

This signal deasserts to indicate that the peripheral can accept

data. In the reverse direction, it indicates whether the data lines

contain ECP command information or data. Normal data are

transferred when Busy (PeriphAck) is high, and an 8-bit command

is transferred when it is low.

PError (nAckReverse)

This signal is used to acknowledge a change in the direction of the

transfer (asserted = forward). The peripheral drives this signal low

to acknowledge nReverseRequest. The host relies upon

nAckReverse to determine when it is permitted to drive the data

bus.

Select (Xflag) I Indicates printer on-line.

NautoFd (HostAck)

Requests a byte of data from the peripheral when it is asserted. In

the forward direction, this signal indicates whether the data lines

contain ECP address or data. Normal data are transferred when

nAutoFd (HostAck) is high, and an 8-bit command is transferred

when it is low.

nFault

(nPeriphReuqest) I

Generates an error interrupt when it is asserted. This signal is valid

only in the forward direction. The peripheral is permitted (but not

required) to drive this pin low to request a reverse transfer during

ECP mode.

nInit

(nReverseRequest) O

This signal sets the transfer direction (asserted = reverse,

deasserted = forward). This pin is driven low to place the channel in

the reverse direction.

nSelectIn (ECPMode) O This signal is always deasserted in ECP mode.

10.3.12 ECP Operation

The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol

before ECP operation. After negotiation, it is necessary to initialize some of the port bits.

(a) Set direction = 0, enabling the drivers.

Publication Release Date: April 7 , 2009

-173- Version 1.94

W83627EHF/EF

W83627EHG

(b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state.

(d) Set mode = 011 (ECP Mode)

ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo,

respectively.

10.3.12.1. Mode Switching

The software must handle P1284 negotiation and all operations prior to a data transfer in SPP or PS/2

modes (000 or 001). The hardware provides an automatic control line handshake, moving data

between the FIFO and the ECP port, only in the data transfer phase (mode 011 or 010).

If the port is in mode 000 or 001, it may switch to any other mode. If the port is not in mode 000 or 001,

it can only be switched into mode 000 or 001. The direction can only be changed in mode 001.

In extended forward mode, the software should wait for the FIFO to be empty before switching back to

mode 000 or 001. In ECP reverse mode, the software should wait for all the data to be read from the

FIFO before changing back to mode 000 or 001.

10.3.12.2. Command/Data

ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction, normal

data are transferred when HostAck is high, and an 8-bit command is transferred when HostAck is low.

The most significant bits of the command indicate whether it is a run-length count (for compression) or

a channel address.

In the reverse direction, normal data are transferred when PeriphAck is high, and an 8-bit command is

transferred when PeriphAck is low. The most significant bit of the command is always zero.

10.3.12.3. Data Compression

The W83627EHF/EHG/EF/EG hardware supports RLE decompression and can transfer compressed

data to a peripheral. Odd (RLE) compression is not supported in the hardware, however. In order to

transfer data in ECP mode, the compression count is written to ecpAFifo and the data byte is written to

ecpDFifo.

10.3.13 FIFO Operation

- 174 -

W83627EHF/EF

W83627EHG/EG

The FIFO threshold is set in LD0 CRO0, bit 6 ~ 3. All data transferred to or from the parallel port can

proceed in DMA or Programmed I/O (non-DMA) mode, as indicated by the selected mode. The FIFO is

used in Parallel Port FIFO mode or ECP Parallel Port Mode. After a reset, the FIFO is disabled.

Publication Release Date: April 7 , 2009

-175- Version 1.94

W83627EHF/EF

W83627EHG

10.3.14 DMA Transfers

DMA transfers are always to or from the ecpDFifo, tFifo, or CFifo. DMA uses the standard PC DMA

services. The ECP requests DMA transfers from the host by activating the PDRQ pin. The DMA

empties or fills the FIFO using the appropriate direction and mode. When the terminal count in the DMA

controller is reached, an interrupt is generated, and serviceIntr is asserted, which will disable the DMA.

10.3.15 Programmed I/O (NON-DMA) Mode

The ECP and parallel port FIFOs can also be operated using interrupt-driven, programmed I/O.

Programmed I/O transfers are

1. To the ecpDFifo at 400h and ecpAFifo at 000h

2. From the ecpDFifo located at 400h

3. To / from the tFifo at 400h.

The host must set dmaEn and serviceIntr to 0 and also must set the direction and state accordingly in

the programmed I/O transfers.

The ECP requests programmed I/O transfers from the host by activating the IRQ pin. The programmed

I/O empties or fills the FIFO using the appropriate direction and mode.

- 176 -

W83627EHF/EF

W83627EHG/EG

11. KEYBOARD CONTROLLER

The W83627EHF/EHG/EF/EG KBC (8042 with licensed KB BIOS) circuit is designed to provide the

functions needed to interface a CPU with a keyboard and/or a PS/2 mouse and can be used with

IBM®-compatible personal computers or PS/2-based systems. The controller receives serial data from

the keyboard or PS/2 mouse, checks the parity of the data, and presents the data to the system as a

byte of data in its output buffer. Then, the controller asserts an interrupt to the system when data are

placed in its output buffer. The keyboard and PS/2 mouse are required to acknowledge all data

transmissions. No transmission should be sent to the keyboard or PS/2 mouse until an

acknowledgement is received for the previous data byte.

8042

P24

P25

P21

P20

P27

P10

P26

P23

P22

P11

KIRQ

MIRQ

GATEA20

KBRST

P17KINH

GP I/O P INS P12~P16

KDAT

KCLK

MCLK

MDAT

Multiplex I/O PINS

Keyboard and Mouse Interface

11.1 Output Buffer

The output buffer is an 8-bit, read-only register at I/O address 60h (Default, PnP programmable I/O

address LD5-CR60 and LD5-CR61). The keyboard controller uses the output buffer to send the scan

code (from the keyboard) and required command bytes to the system. The output buffer can only be

read when the output buffer full bit in the register (in the status register) is logical 1.

11.2 Input Buffer

Publication Release Date: April 7 , 2009

-177- Version 1.94

W83627EHF/EF

W83627EHG

The input buffer is an 8-bit, write-only register at I/O address 60h or 64h (Default, PnP programmable

I/O address LD5-CR60, LD5-CR61, LD5-CR62, and LD5-CR63). Writing to address 60h sets a flag to

indicate a data write; writing to address 64h sets a flag to indicate a command write. Data written to I/O

address 60h is sent to the keyboard (unless the keyboard controller is expecting a data byte) through

the controller's input buffer only if the input buffer full bit (in the status register) is logical 0.

11.3 Status Reg ister

The status register is an 8-bit, read-only register at I/O address 64h (Default, PnP programmable I/O

address LD5-CR62 and LD5-CR63) that holds information about the status of the keyboard controller

and interface. It may be read at any time.

BIT BIT FUNCTION DESCRIPTION

0 Output Buffer Full 0: Output buffer empty

1: Output buffer full

1 Input Buffer Full 0: Input buffer empty

1: Input buffer full

2 System Flag This bit may be set to 0 or 1 by writing to the

system flag bit in the command byte of the

keyboard controller. It defaults to 0 after a

power-on reset.

3 Command/Data 0: Data byte

1: Command byte

4 Inhibit Switch 0: Keyboard is inhibited

1: Keyboard is not inhibited

5 Auxiliary Device Output Buffer 0: Auxiliary device output buffer empty

1: Auxiliary device output buffer full

6 General Purpose Time-out 0: No time-out error

1: Time-out error

7 Parity Error 0: Odd parity

1: Even parity (error)

11.4 Commands

- 178 -

W83627EHF/EF

W83627EHG/EG

COMMAND FUNCTION

20h Read Command Byte of Keyboard Controller

60h Write Command Byte of Keyboard Controller

BIT

BIT DEFINITION

Reserved

IBM Keyboard Translate Mode

Disable Auxiliary Device

Disable Keyboard

Reserve

System Flag

Enable Auxiliary Interrupt

Enable Keyboard Interrupt

A4h Test Password

Returns 0Fah if Password is loaded

Returns 0F1h if Password is not loaded

A5h Load Password

Load Password until a logical 0 is received from the system

A6h Enable Password

Enable the checking of keystrokes for a match with the password

A7h Disable Auxiliary Device Interface

A8h Enable Auxiliary Device Interface

A9h Interface Test

BIT

BIT DEFINITION

No Error Detected

Auxiliary Device "Clock" line is stuck low

Auxiliary Device "Clock" line is stuck high

Auxiliary Device "Data" line is stuck low

AAh Self-test

Returns 055h if self-test succeeds

Publication Release Date: April 7 , 2009

-179- Version 1.94

W83627EHF/EF

W83627EHG

COMMAND FUNCTION

ABh Interface Test

BIT

BIT DEFINITION

No Error Detected

Keyboard "Clock" line is stuck low

Keyboard "Clock" line is stuck high

Keyboard "Data" line is stuck low

Keyboard "Data" line is stuck high

ADh Disable Keyboard Interface

AEh Enable Keyboard Interface

C0h Read Input Port (P1) and send data to the system

C1h Continuously puts the lower four bits of Port1 into the STATUS register

C2h Continuously puts the upper four bits of Port1 into the STATUS register

D0h Send Port 2 value to the system

D1h Only set / reset GateA20 line based on system data bit 1

D2h Send data back to the system as if it came from the Keyboard

D3h Send data back to the system as if it came from Auxiliary Device

D4h Output next received byte of data from system to Auxiliary Device

E0h Reports the status of the test inputs

FXh Pulse only RC (the reset line) low for 6μs if the Command byte is even

- 180 -

W83627EHF/EF

W83627EHG/EG

11.5 Hardware GATEA20/Keyboard Reset Control Logic

The KBC includes hardware control logic to speed-up GATEA20 and KBRESET. This control logic is

controlled by LD5-CRF0 as follows:

11.5.1 KB Control Register

BIT 7 6 5 4 3 2 1 0

NAME KCLKS1 KCLKS0 Reserved Reserved Reserved P92EN HGA20 HKBRST#

KCLKS1, KCLKS0

These two bits select the KBC clock rate.

00: KBC clock input is 6 MHz

01: KBC clock input is 8 MHz

10: KBC clock input is 12 MHz

11: KBC clock input is 16 MHz

P92EN (Port 92 Enable)

1: Enables Port 92 to control GATEA20 and KBRESET.

0: Disables Port 92 functions.

HGA20 (Hardware GATEA20)

1: Selects hardware GATEA20 control logic to control GATE A20 signal.

0: Disables hardware GATEA20 control logic function.

HKBRST# (Hardware Keyboard Reset)

1: Selects hardware KB RESET control logic to control KBRESET signal.

0: Disables hardware KB RESET control logic function.

When the KBC receives data that follows a "D1" command, the hardware control logic sets or clears

GATEA20 according to received data bit 1. Similarly, the hardware control logic sets or clears

KBRESET depending on received data bit 0. When the KBC receives an "FE" command, the

KBRESET is pulse low for 6μs (Min.) with a 14μs (Min.) delay.

Publication Release Date: April 7 , 2009

-181- Version 1.94

W83627EHF/EF

W83627EHG

GATEA20 and KBRESET are controlled by either software or hardware logic, and they are mutually

exclusive. Then, GATEA20 and KBRESET are merged with Port92 when the P92EN bit is set.

11.5.2 Port 92 Control Register

BIT 7 6 5 4 3 2 1 0

NAME Res. (0) Res. (0) Res. (1) Res. (0) Res. (0) Res. (1) SGA20 PLKBRST

SGA20 (Special GATE A20 Control)

1: Drives GATE A20 signal to high.

0: Drives GATE A20 signal to low.

PLKBRST# (Pull-Low KBRESET)

A logical 1 on this bit causes KBRESET to drive low for 6 μS(Min.) with a 14 μS(Min.) delay. Before

issuing another keyboard-reset command, the bit must be cleared.

- 182 -

W83627EHF/EF

W83627EHG/EG

12. POWER MANAGEMENT EVENT

The PME# (pin 86) signal is connected to the South Bridge and is used to wake up the system from S1

~ S5 sleeping states.

One control bit and four registers in the W83627EHF/EHG/EF/EG are associated with the PME

function. The control bit is at Logical Device A, CR[F2h], bit[0] and is for enabling or disabling the PME

function. If this bit is set to “0”, the W83627EHF/EHG/EF/EG won’t output any PME signal when any of

the wake-up events has occurred and is enabled. The four registers are divided into PME status

registers and PME interrupt registers of wake-up events Note.1.

1) The PME status registers of wake-up event:

- At Logical Device A, CR[F3h] and CR[F4h]

- Each wake-up event has its own status

- The PME status should be cleared by writing a “1” before enabling its corresponding bit in the

PME interrupt registers

2) The PME interrupt registers of wake-up event:

- At Logical Device A, CR[F6h] and CR[F7h]

- Each wake-up event can be enabled / disabled individually to generate a PME# signal

Note.1 PME wake-up events that the W83627EHF/EHG/EF/EG supports include:

z Mouse IRQ event

z Keyboard IRQ event

z Printer IRQ event

z Floppy IRQ event

z UART A IRQ event

z UART B IRQ event

z Hardware Monitor IRQ event

z WDTO# event

z MIDI IRQ event

z RIB (UARTB Ring Indicator) event

12.1 Resume Reset Logic

The RSMRST# (Pin 75) signal is a reset output and is used as the 3VSB power-on reset signal for the

South Bridge.

Publication Release Date: April 7 , 2009

-183- Version 1.94

W83627EHF/EF

W83627EHG

When the W83627EHF/EHG/EF/EG detects the 3VSB voltage rises to “V1”, it then starts a delay – “t”

before the rising edge of RSMRST# asserting. If the 3VSB voltage falls below “V2”, the RSMRST#

de-asserts immediately.

Timing and voltage parameters are shown in the following figure and table.

SYMBOL MIN. MAX. UNIT

t 80 130 mS

V1 2.6 2.65 V

V2 2.4 2.45 V

12.2 PWROK Generation

The PWROK (Pin 71) signal is an output and is used as the 3VCC power-on reset signal.

When the W83627EHF/EHG/EF/EG detects the 3VCC voltage rises to “V3”, it then starts a delay – “t2”

before the rising edge of PWROK asserting. If the 3VCC voltage falls below “V4”, the PWROK

de-asserts immediately.

Timing and voltage parameters are shown in figure and table.

- 184 -

W83627EHF/EF

W83627EHG/EG

SYMBOL MIN. MAX. UNIT

t2 300 600 mS

V3 2.6 2.65 V

V4 2.4 2.45 V

Originally, the t2 timing is between 300 mS to 600 mS, but it can be changed to 200 mS to 300 mS by

programming Logical Device A, CR[E6h], bit 3 to “1”. Furthermore, the W83627EHF/EHG/EF/EG

provides four different extra delay time of PWROK for various demands. The four extra delay time are

designed at Logical Device A, CR[E6h], bits 2~1. The following table shows the definitions of Logical

Device A, CR[E6h] bits 3 ~1.

LOGICAL DEVICE A,

CR[E6H] BIT DEFINITION

PWROK_DEL (first stage) (VSB)

Set the delay time when rising from PWROK_LP to

PWROK_ST.

0: 300 ~ 600 mS.

1: 200 ~ 300 mS.

2~1

PWROK_DEL (VSB)

Set the delay time when rising from PWROK_ST to

PWROK.

00: No delay time. 01: Delay 32 mS

10: 96 mS 11: Delay 250 mS

Publication Release Date: April 7 , 2009

-185- Version 1.94

W83627EHF/EF

W83627EHG

For example, if Logical Device A, CR[E6h] bit 2 is set to “0” and bits 2~1 are set to “10”, the range of t2

timing is from 396(300 + 96) mS to 596(500 + 96) mS.

- 186 -

W83627EHF/EF

W83627EHG/EG

13. SERIALIZED IRQ

The W83627EHF/EHG/EF/EG supports a serialized IRQ scheme. This allows a signal line to be used

to report the parallel interrupt requests. Since more than one device may need to share the signal serial

SERIRQ signal, an open drain signal scheme is employed. The clock source is the PCI clock. The

serialized interrupt is transferred on the SERIRQ signal, one cycle consisting of three frames types: the

Start Frame, the IRQ/Data Frame, and the Stop Frame.

13.1 Start Frame

There are two modes of operation for the SERIRQ Start Frame: Quiet mode and Continuous mode.

In the Quiet mode, the W83627EHF/EHG/EF/EG drives the SERIRQ signal active low for one clock,

and then tri-states it. This brings all the state machines of the W83627EHF/EHG/EF/EG from idle to

active states. The host controller (the South Bridge) then takes over driving SERIRQ signal low in the

next clock and continues driving the SERIRQ low for programmable 3 to 7 clock periods. This makes

the total number of clocks low 4 to 8 clock periods. After these clocks, the host controller drives the

SERIRQ high for one clock and then tri-states it.

In the Continuous mode, the START Frame can only be initiated by the host controller to update the

information of the IRQ/Data Frame. The host controller drives the SERIRQ signal low for 4 to 8 clock

periods. Upon a reset, the SERIRQ signal is defaulted to the Continuous mode for the host controller to

initiate the first Start Frame.

Please see the diagram below for more details.

Start Frame Timing with source sampled a low pulse on IRQ1.

Publication Release Date: April 7 , 2009

-187- Version 1.94

W83627EHF/EF

W83627EHG

SER

IRQ

PCICL

Host Controller

IRQ1

Drive Source

None

IRQ0 FRAME

IRQ1 FRAME

SMI#

FRAME

None

START

START FRAME

H=Host Control SL=Slave Control R=Recovery T=Turn-around S=Sample

Note:

1. The Start Frame pulse can be 4-8 clocks wide.

2. The first clock of Start Frame is driven low by the W83627EHF/EHG/EF/EG because IRQ1 of the

W83627EHF/EHG/EF/EG needs an interrupt request. Then the host takes over and continues to

pull the SERIRQ low.

13.2 IRQ/Data Frame

Once the Start Frame has been initiated, the W83627EHF/EHG/EF/EG must start counting frames

based on the rising edge of the start pulse. Each IRQ/Data Frame has three clocks: the Sample phase,

the Recovery phase, and the Turn-around phase.

During the Sample phase, the W83627EHF/EHG/EF/EG drives SERIRQ low if the corresponding IRQ

is active. If the corresponding IRQ is inactive, then SERIRQ must be left tri-stated. During the Recovery

phase, the W83627EHF/EHG/EF/EG device drives the SERIRQ high. During the Turn-around phase,

the W83627EHF/EHG/EF/EG device leaves the SERIRQ tri-stated. The W83627EHF/EHG/EF/EG

starts to drive the SERIRQ line from the beginning of "IRQ0 FRAME" based on the rising edge of

PCICLK.

The IRQ/Data Frame has a specific numeral order, as shown in Table 13.1.

Table 13.1 SERIRQ Sampling Periods

- 188 -

W83627EHF/EF

W83627EHG/EG

SERIRQ SAMPLING PERIODS

IRQ/DATA FRAME SIGNAL SAMPLED # OF CLOCKS PAST

START

EMPLOYED BY

1 IRQ0 2 -

2 IRQ1 5 Keyboard

3 SMI# 8 -

4 IRQ3 11 UART B

5 IRQ4 14 UART A

6 IRQ5 17 -

7 IRQ6 20 FDC

8 IRQ7 23 LPT

9 IRQ8 26 -

10 IRQ9 29 -

11 IRQ10 32 -

12 IRQ11 35 -

13 IRQ12 38 Mouse

14 IRQ13 41 -

15 IRQ14 44 -

16 IRQ15 47 -

17 IOCHCK# 50 -

18 INTA# 53 -

19 INTB# 56 -

20 INTC# 59 -

21 INTD# 62 -

32:22 Unassigned 95 -

Publication Release Date: April 7 , 2009

-189- Version 1.94

W83627EHF/EF

W83627EHG

13.3 Stop Frame

After all IRQ/Data Frames have completed, the host controller will terminates SERIRQ with a Stop

frame. Only the host controller can initiate the Stop Frame by driving SERIRQ low for 2 or 3 clocks. If

the Stop Frame is low for 2 clocks, the Sample mode of next SERIRQ cycle’s Sample mode is the

Quiet mode. If the Stop Frame is low for 3 clocks, the Sample mode of next SERIRQ cycle is the

Continuous mode.

Please see the diagram below for more details.

Stop Frame Timing with Host Using 17 SERIRQ sampling period.

SERIRQ

PCICLK

Host ControllerIRQ15

Driver

None

IRQ14 IRQ15

S R T

IOCHCK#

None

STOP

R T

STOP FRAME

START

NEXT CYCLE

FRAME

H=Host Control R=Recovery T=Turn-around S=Sample I= Idle.

Note:

1. There may be none, one or more Idle states during the Stop Frame.

2. The Start Frame pulse of next SERIRQ cycle may or may not start immediately after the

turn-around clock of the Stop Frame.

- 190 -

W83627EHF/EF

W83627EHG/EG

14. WATCHDOG TIMER

The WDTO# pin is a multi-function pin with GP50 functions and is configured to the WDTO# function, if

Configuration Register CR[2Dh], bit 0 is set to zero.

The Watchdog Timer of the W83627EHF/EHG/EF/EG consists of an 8-bit programmable time-out

counter and a control and status register. The time-out counter ranges from 1 to 255 minutes in the

minute mode, or 1 to 255 seconds in the second mode. The units of Watchdog Timer counter are

selected at Logical Device 8, CR[F5h], bit[3]. The time-out value is set at Logical Device 8, CR[F6h].

Writing zero disables the Watchdog Timer function. Writing any non-zero value to this register causes

the counter to load this value into the Watchdog Timer counter and start counting down.

The W83627EHF/EHG/EF/EG outputs a low signal to the WDTO# pin (pin 77) when a time-out event

occurs. In other words, when the value is counted down to zero, the timer stops, and the

W83627EHF/EHG/EF/EG sets the WDTO# status bit in Logical Device 8, CR[F7h], bit[4], outputting a

low signal to the WDTO# pin(pin 77). Writing a zero will clear the status bit and the WDTO# pin returns

to high. Writing a zero will clear the status bit. This bit will also be cleared if LRESET# or PWROK#

signal is asserted.

Additionally, GP40 (pin 85), GP42 (pin 83), GP44 (pin 81) and GP46 (pin 79) provides an alternative

WDTO# function. This function can be configured by the relative GPIO control register.

Please note that the output type of WDTO# (pin 77) and GP42 (pin 83) is push-pull and that of GP40

(pin 85), GP44 (pin 81) and GP46 (pin 79) is open-drain.

Publication Release Date: April 7 , 2009

-191- Version 1.94

W83627EHF/EF

W83627EHG

15. VID INPUTS AND OUTPUTS

The W83627EHF/EHG/EF/EG provides eight pins for VID input or output function. The default function

is VID input. These pins can be configured to VID output function by setting Logical Device B, CR[F0h],

bit 7 to 0. The configuration is applied to the 8 pins as a group. None of them can be individually set to

input or output.

15.1 VID Input Detection

The W83627EHF/EHG/EF/EG supports Intel VRM 9/10/11 and AMD VRM VID detections. H/W

strapping and S/W programming can set the following three input levels. a) and b) can be set by H/W

strapping or S/W programming, while c) can only be set by S/W programming.

a) TTL (Vih = 2 V; Vil = 0.8V) –

1) Add a pulled-down resistor at Pin 77(EN_GTL), or

2) Set Configuration Register CR[2Ch], bit 3 to “0”;

b) GTL (Vih = 0.6 V; Vil = 0.4 V) – (Default)

1) No extra pulled-up resistor needed, or

2) Set Configuration Register CR[2Ch], bit 3 to “1”;

c) AMD VRM (Vih = 1.4V; Vil = 0.8V) –

Set Configuration Register CR[2Ch], bit 3 to “1” and Logical Device B, CR[F0h], but 6 to “1”.

The input data can be read in the data register at Logical Device B, CR[F1h], bit 7 ~ 0. It is a read/write

15.2 VID Output Control

- 192 -

W83627EHF/EF

W83627EHG/EG

The output type of the eight VID pins is push-pull, and they drive to 3VCC (3.3V) when configured to

the output mode. The output data can be set in the data register (Logical Device B, CR[F1h], bit 7 ~ 0).

The written data can be read if Configuration Register CR[2Ch], bit 3 is set to “0”.

16. PCI RESET BUFFERS

The W83627EHF/EHG/EF/EG has five copies of LRESET# output buffers. LRESET# is LPC Interface

Reset, to which PCI Reset is connected. The five copies of LRESET# in the W83627EHF/EHG/EF/EG

are designated RSTOUT0#, RSTOUT1#, RSTOUT2#, RSTOUT3# and RSTOUT4#. All of them are

RSTOUT0# is an open-drain output buffer of LRESET#. This signal needs an external pulled-up

resistor of 3.3V or 5V.

RSTOUT1#, RSTOUT2#, RSTOUT3# and RSTOUT4# are push-pull output buffers of LRESET#. Each

of them outputs 3.3V, voltage and the state is low when the 3VSB power is the only power source.

Publication Release Date: April 7 , 2009

-193- Version 1.94

W83627EHF/EF

W83627EHG

17. CONFIGURATION REGISTER

17.1 Chip (Global) Control Register

CR 02h. (Software Reset; Write Only)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 Write “1” Only Software RESET.

CR 07h. (Logical Devi ce; Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W Logical Device Number.

CR 20h. (Chip ID, MSB; Read Only)

BIT READ / WRITE DESCRIPTION

7~0 Read Only Chip ID number = 88h (higher byte).

CR 21h. (Chip ID, LSB; Read Only)

BIT READ / WRITE DESCRIPTION

7~0 Read Only Chip ID number = 6Xh (lower byte). X for IC version

CR 22h. (Device Power Down; Default FFh)

BIT READ / WRITE DESCRIPTION

7 Reserved.

6 R / W HM Power Down. 0: Power down. 1: No power down.

5 R / W URB Power Down. 0: Power down. 1: No power down.

- 194 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

4 R / W URA Power Down. 0: Power down. 1: No power down.

3 R / W PRT Power Down. 0: Power down. 1: No power down.

2 Reserved.

1 Reserved.

0 R / W FDC Power Down. 0: Power down. 1: No power down.

CR 23h. (IPD; Default 00h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W IPD (Immediate Power Down). When set to 1, whole chip is put into power

down mode immediately.

CR 24h. (Global Option; Default 0100_0ss0b) s: value by strapping

BIT READ / WRITE DESCRIPTION

7 Reserved.

6 R / W

CLKSEL => Input clock rate selection

= 0 The clock input on pin18 is 24MHz.

= 1 The clock input on pin18 is 48MHz. (Default)

5 Reserved.

4 R / W

Enable SYSFANOUT as Output Buffer (For H version only)

=0 SYSFANOUT is Open-Drain. (Default)

=1 SYSFANOUT can drive logical high or logical low.

Publication Release Date: April 7 , 2009

-195- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

3 R / W

Enable CPUFANOUT0 as Output Buffer (For H version only)

=0 CPUFANOUT0 is Open-Drain. (Default)

=1 CPUFANOUT0 can drive logical high or logical low.

2 Read Only

ENKBC => Enable keyboard controller

= 0 KBC is disabled after hardware reset.

= 1 KBC is enabled after hardware reset.

This bit is read only, and set/reset by power-on strapping pin (PIN54;

SOUTA).

1 Reserved.

0 R / W

PNPCVS =>

= 0 The compatible PNP address select registers have default values.

= 1 The compatible PNP address select registers have no default value.

CR 25h. (Interface tri-state Enable; Default 00h)

BIT READ / WRITE DESCRIPTION

7~6 Reserved.

5 R / W URBTRI

4 R / W URATRI

3 R / W PRTTRI

2~1 Reserved.

0 R / W FDCTRI.

CR 26h. (Global Option; Default 0s000000b) s: value by strapping

BIT READ / WRITE DESCRIPTION

- 196 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7 R / W

SEL4FDD =>

= 0 Select two FDD mode.

= 1 Select four FDD mode.

6 R / W

HEFRAS =>

= 0 Write 87h to location 2E twice.

= 1 Write 87h to location 4E twice.

The corresponding power-on strapping pin is RTSA# (pin 51).

5 R / W

LOCKREG =>

= 0 Enable R/W configuration registers.

= 1 Disable R/W configuration registers.

4 Reserved.

3 R / W

DSFDLGRQ =>

= 0 Enable FDC legacy mode on IRQ and DRQ selection, then DO

= 1 Disable FDC legacy mode on IRQ and DRQ selection, then DO

2 R / W

DSPRLGRQ =>

= 0 Enable PRT legacy mode on IRQ and DRQ selection, then DCR

= 1 Disable PRT legacy mode on IRQ and DRQ selection, then DCR

Publication Release Date: April 7 , 2009

-197- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

1 R / W

DSUALGRQ =>

= 0 Enable UART A legacy mode on IRQ selection, then HCR register

(base address + 4) bit 3 is effective on selecting IRQ.

= 1 Disable UART A legacy mode on IRQ selection, then HCR register

(base address + 4) bit 3 is not effective on selecting IRQ.

0 R / W

DSUBLGRQ =>

= 0 Enable UART B legacy mode on IRQ selection, then HCR register

(base address + 4) bit 3 is effective on selecting IRQ.

= 1 Disable UART B legacy mode on IRQ selection, then HCR register

(base address + 4) bit 3 is not effective on selecting IRQ.

CR 27h. (Reserved)

CR 28h. (Global Option; Default 50h)

BIT READ / WRITE DESCRIPTION

7~5 Reserved.

4 R / W

Select to enable/disable decoding of BIOS ROM range 000E xxxxh.

= 0 Enable decoding of BIOS ROM range at 000E xxxxh.

= 1 Disable decoding of BIOS ROM range at 000E xxxxh.

3 R / W

Select to enable/disable decoding of BIOS ROM range FFFE xxxxh.

= 0 Enable decoding of BIOS ROM range at FFFE xxxxh.

= 1 Disable decoding of BIOS ROM range at FFFE xxxxh.

2~0 R / W

PRTMODS2 ~ 0 =>

= 0xx Parallel Port Mode.

= 1xx Reserved.

CR 29h. (OVT#/SMI#, UART A, Game port & MIDI pin select; Default 04h)

- 198 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7 Reserved.

6 R / W

PIN5 function select

= 0 PIN5 Æ OVT#

= 1 PIN5 Æ SMI#.

5~4 Reserved.

3 R / W

PIN49~54,56~57 function select

= 0 PIN49~54,56~57 Æ UART A.

= 1 PIN49~54,56~57 Æ GPIO6.

2~1 R / W

PIN119~120 function select

Bit-2 Bit-1 PIN119~PIN120 function

0 0 PIN 119~120 Æ CPUFANIN1, CPUFANOUT1

0 1 PIN 119~120 Æ GP21, GP20

1 x PIN 119~120 Æ MSI, MSO (Default)

0 R / W

PIN121~128 function select

= 0 PIN121~128 Æ Game Port.

= 1 PIN121~128 Æ GPIO1.

CR 2Ah. (I2C pin select; Default 00h) (VSB Power)

BIT READ / WRITE DESCRIPTION

7~2 Reserved.

1 R / W

PIN89, PIN90 function select (I2C interafce)

= 0 {PIN89, PIN90} Æ set by CR2C [6:5].

= 1 {PIN89, PIN90} Æ SDA, SCL.

Publication Release Date: April 7 , 2009

-199- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

0 R / W

KB, MS pin function select

= 0 KB, MS function.

= 1 GPIO function.

CR 2Bh. (Reserved)

CR 2Ch. (GPIO3, GPIO4 multi-function selection; Default 00 h) (VSB Power)

BIT READ / WRITE DESCRIPTION

7 R / W

PIN88 Select

= 0 PIN88Æ GP34

= 1 PIN88Æ RSTOUT4#

6 R / W

PIN89 Select

= 0 PIN89Æ GP33

= 1 PIN89Æ RSTOUT3#

Note: The bit will be ignored while CR2A bit-1 is High.

5 R / W

PIN90 Select

= 0 PIN90Æ GP32

= 1 PIN90Æ RSTOUT2#

Note: The bit will be ignored while CR2A bit-1 is High.

4 Reserved

3 R / W

EN_VRM10 Configure bit

= 0 VID input voltage is TTL.

= 1 VID input voltage is VRM10.

The bit is strapping by PIN77 (GP50).--- Pull high to 3VSB.

2 R / W

EN_PWRDN. (VBAT)

= 0 Thermal shutdown function is disabled.

= 1 Enable thermal shutdown function.

- 200 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

1~0 R / W

PIN78~85 function select

Bit-1 Bit-0 PIN78~PIN85 function

0 0

PIN82 Æ Reserved (tri-state)

PIN83 Æ Reserved (always low)

Others Æ GPIO4

0 1

PIN82 Æ IRRX

PIN83 Æ IRTX

Others Æ GPIO4

1 0 PIN 78~85 Æ GPIO4

1 1 PIN 78~85 Æ UART B

CR 2Dh. (GPIO5 and power control signals multi-function selection; default 21h) (VSB Power)

BIT READ / WRITE DESCRIPTION

7 R / W

PIN67 Select (reset by RSMRST#)

= 0 PIN67Æ PSOUT#

= 1 PIN67Æ GPIO57

6 R / W

PIN68 Select (reset by RSMRST#)

= 0 PIN68Æ PSIN

= 1 PIN68Æ GPIO56

5 R / W

PIN70 Select (reset by RSMRST#)

= 0 PIN70Æ SUSLED

= 1 PIN70Æ GPIO55

4 R / W

PIN71 Select (reset by RSMRST#)

= 0 PIN71Æ PWROK

= 1 PIN71Æ GPIO54

Publication Release Date: April 7 , 2009

-201- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

3 R / W

PIN72 Select (reset by RSMRST#)

= 0 PIN72Æ PSON#

= 1 PIN72Æ GPIO53

2 R / W

PIN73 Select (reset by RSMRST#)

= 0 PIN73Æ SUSB#

= 1 PIN73Æ GPIO52

1 R / W

PIN75 Select (reset by RSMRST#)

= 0 PIN75Æ RSMRST#

= 1 PIN75Æ GPIO51

0 R / W

PIN77 Select (reset by RSMRST#)

= 0 PIN77Æ WDTO#

= 1 PIN77Æ GPIO50

CR 2Eh. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W Test Mode Bits: Reserved for Nuvoton.

CR 2Fh. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W Test Mode Bits: Reserved for Nuvoton.

17.2 Logical Device 0 (FDC)

CR 30h. (Default 01h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

- 202 -

W83627EHF/EF

W83627EHG/EG

CR 60h, 61h. (Default 03h,F0h)

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select FDC I/O base address <100h : FF8h> on 8

bytes boundary.

CR 70h. (Default 06h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for FDC.

CR 74h. (Default 02h)

BIT READ / WRITE DESCRIPTION

7~3 Reserved.

2~0 R / W

These bits select DRQ resource for FDC.

000: DMA0. 001: DMA1. 010: DMA2. 011: DMA3.

1xx: No DMA active.

CR F0h. (Default 8Eh)

BIT READ / WRITE DESCRIPTION

7 R / W

This bit controls the internal pull-up resistors of the FDC input pins

RDATA#, INDEX#, TRAK0#, DSKCHG# and WP#.

0: The internal pull-up resistors of FDC are turned on.

1: The internal pull-up resistors of FDC are turned off. (Default)

6 R / W

This bit determines the polarity of all FDD interface signals.

0: FDD interface signals are active low.

1: FDD interface signals are active high.

Publication Release Date: April 7 , 2009

-203- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

5 R / W When this bit is logic 0, indicates a second drive is installed and is reflected

in status register A. (PS2 mode only)

4 R / W

Swap Drive 0, 1 Mode =>

0: No Swap. 1: Drive and Motor select 0 and 1 are swapped.

3~2 R / W

Interface Mode. 00: Model 30. 01: PS/2.

10: Reserved. 11: AT Mode

1 R / W

FDC DMA Mode. 0: Burst Mode is enabled

1: Non-Burst Mode.

0 R / W

Floppy Mode. 0: Normal Floppy Mode.

1: Enhanced 3-mode FDD.

CR F1h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~6 R / W

Boot Floppy. 00: FDD A. 01: FDD B.

10: FDD C. 11: FDD D.

5~4 R / W Media ID1, Media ID0. These bits will be reflected on FDC’s Tape Drive

3~2 R / W

Density Select.

00: Normal. 01: Normal.

10: 1 (Forced to logic 1). 11: 0 (Forced to logic 0).

1 R / W

DISFDDWR =>

0: Enable FDD write.

1: Disable FDD write (forces pins WE, WD stay high).

0 R / W

SWWP =>

0: Normal, use WP to determine whether the FDD is write protected or not.

1: FDD is always write-protected.

CR F2h. (Default FFh)

- 204 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7~6 R / W FDD D Drive Type.

5~4 R / W FDD C Drive Type.

3~2 R / W FDD B Drive Type.

1~0 R / W FDD A Drive Type.

CR F4h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7 Reserved.

6 R / W

0: Enable FDC Pre-compensation.

1: Disable FDC Pre-compensation.

5 Reserved.

4~3 R / W

Data Rate Table selection (Refer to TABLE A).

00: Select regular drives and 2.88 format.

01: 3-mode drive. 10: 2 Meg Tape. 11: Reserved.

2 Reserved.

1~0 R / W Drive Type selection (Refer to TABLE B).

CR F5h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W Same as FDD0 of CR F5h.

TABLE A

DRIVE RATE TABLE

SELECT DATA RATE SELECTED DATA RATE

DRTS1 DRTS0 DRATE1 DRATE0 MFM FM

SELDEN

0 0 1 1 1Meg --- 1

Publication Release Date: April 7 , 2009

-205- Version 1.94

W83627EHF/EF

W83627EHG

DRIVE RATE TABLE

SELECT DATA RATE SELECTED DATA RATE

DRTS1 DRTS0 DRATE1 DRATE0 MFM FM

SELDEN

0 0 500K 250K 1

0 1 300K 150K 0

1 0 250K 125K 0

1 1 1Meg --- 1

0 0 500K 250K 1

0 1 500K 250K 0

0 1

1 0 250K 125K 0

1 1 1Meg --- 1

0 0 500K 250K 1

0 1 2Meg --- 0

1 0

1 0 250K 125K 0

TABLE B

DTYPE0 DTYPE1 DRVDEN0 (PI N 2) DRVDEN1 (PIN 3) DRIVE TYPE

0 0 SELDEN DRATE0

4/2/1 MB 3.5”“

2/1 MB 5.25”

2/1.6/1 MB 3.5” (3-MODE)

0 1 DRATE1 DRATE0

- 206 -

W83627EHF/EF

W83627EHG/EG

DTYPE0 DTYPE1 DRVDEN0 (PIN 2) DRVDEN1 (PIN 3) DRIVE TYPE

1 0 SELDEN DRATE0

1 1 DRATE0 DRATE1

17.3 Logical Device 1 (Parallel Port)

CR 30h. (Default 01h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

CR 60h, 61h. (Default 0 3h, 78h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

These two registers select PRT I/O base address.

<100h : FFCh> on 4 bytes boundary (EPP not supported) or

<100h : FF8h> on 8 bytes boundary (all modes supported, EPP is only

available when the base address is on 8 byte boundary).

CR 70h. (Default 07h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for PRT.

CR 74h. (Default 04h)

BIT READ / WRITE DESCRIPTION

7~3 Reserved.

Publication Release Date: April 7 , 2009

-207- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

2~0 R / W

These bits select DRQ resource for PRT.

000: DMA0. 001: DMA1. 010: DMA2. 011: DMA3.

1xx: No DMA active.

CR F0h. (Default 3Fh)

BIT READ / WRITE DESCRIPTION

7 Reserved.

6~3 R / W ECP FIFO Threshold.

2~0 R / W

Parallel Port Mode selection (CR28 bit2 PRTMODS2 = 0).

000: Standard and Bi-direction (SPP) mode.

001: EPP – 1.9 and SPP mode.

010: ECP mode.

011: ECP and EPP – 1.9 mode.

100: Printer Mode.

101: EPP – 1.7 and SPP mode.

110: Reserved.

111: ECP and EPP – 1.7 mode.

17.4 Logical Device 2 (UART A)

CR 30h. (Default 01h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

CR 60h, 61h. (Default 03h, F8h)

BIT READ / WRITE DESCRIPTION

- 208 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select Serial Port 1 I/O base address <100h : FF8h>

on 8 bytes boundary.

CR 70h. (Default 04h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for Serial Port 1.

CR F0h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~2 Reserved.

1~0 R / W

00: UART A clock source is 1.8462 MHz (24 MHz / 13).

01: UART A clock source is 2 MHz (24 MHz / 12).

10: UART A clock source is 24 MHz (24 MHz / 1).

11: UART A clock source is 14.769 MHz (24 MHz / 1.625).

17.5 Logical Device 3 (UART B)

CR 30h. (Default 01h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

CR 60h, 61h. (Default 02h, F8h)

BIT READ / WRITE DESCRIPTION

Publication Release Date: April 7 , 2009

-209- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select Serial Port 2 I/O base address <100h : FF8h>

on 8 bytes boundary.

CR 70h. (Default 03h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for Serial Port 2.

CR F0h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3 R / W

0: No reception delay when SIR is changed from TX mode to RX mode.

1: Reception delay 4 characters-time (40 bit-time) when SIR is changed

from TX mode to RX mode.

2 R / W

0: No transmission delay when SIR is changed from RX mode to TX mode.

1: Transmission delay 4 characters-time (40 bit-time) when SIR is changed

from RX mode to TX mode.

1~0 R / W

00: UART B clock source is 1.8462 MHz (24 MHz / 13).

01: UART B clock source is 2 MHz (24 MHz / 12).

10: UART B clock source is 24 MHz (24 MHz / 1).

11: UART B clock source is 14.769 MHz (24 MHz / 1.625).

CR F1h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7 R / W Reserved.

- 210 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

6 R / W

IRLOCSEL => IR I/O pins’ location selection.

0: Through SINB / SOUTB.

1: Through IRRX / IRTX.

5~3 R / W IRMODE => IR function mode selection. See below table.

2 R / W

IR half / full duplex function selection.

0: IR function is Full Duplex.

1: IR function is Half Duplex.

1 R / W

0: SOUTB pin of UART B function or IRTX pin of IR function in normal

condition.

1: Inverse SOUTB pin of UART B function or IRTX pin of IR function.

0 R / W

0: SINB pin of UART B function or IRRX pin of IR function in normal

condition.

1: Inverse SINB pin of UART B function or IRRX pin of IR function.

IR MODE IR FUNCTION IRTX IRRX

00X Disable Tri-state High

010* IrDA Active pulse 1.6 μS Demodulation into SINB/IRRX

011* IrDA Active pulse 3/16 bit time Demodulation into SINB/IRRX

100 ASK-IR Inverting IRTX/SOUTB pin Routed to SINB/IRRX

101 ASK-IR

Inverting IRTX/SOUTB & 500

KHZ clock

Routed to SINB/IRRX

110 ASK-IR Inverting IRTX/SOUTB Demodulation into SINB/IRRX

Publication Release Date: April 7 , 2009

-211- Version 1.94

W83627EHF/EF

W83627EHG

IR MODE IR FUNCTION IRTX IRRX

111* ASK-IR

Inverting IRTX/SOUTB & 500

KHZ clock

Demodulation into SINB/IRRX

Note: The notation is normal mode in the IR function.

17.6 Logical Device 5 (Keyboard Controller)

CR 30h. (Default 01h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

CR 60h, 61h. (Default 0 0h,60h)

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select the first KBC I/O base address <100h : FFFh>

on 1 byte boundary.

CR 62h, 63h. (Default 0 0h,64h)

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select the second KBC I/O base address <100h :

FFFh> on 1 byte boundary.

CR 70h. (Default 01h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for KINT. (Keyboard interrupt)

- 212 -

W83627EHF/EF

W83627EHG/EG

CR 72h. (Default 0Ch)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for MINT. (PS/2 Mouse interrupt)

CR F0h. (Default83h)

BIT READ / WRITE DESCRIPTION

7~6 R / W

KBC clock rate selection

00: 6MHz

01: 8MHz

10: 12MHz

11: 16MHz

5~3 Reserved.

2 R / W

0: Port 92 disable.

1: Port 92 enable.

1 R / W

0: Gate A20 software control.

1: Gate A20 hardware speed up.

0 R / W

0: KBRST# software control.

1: KBRST# hardware speed up.

17.7 Logical Device 7 (GPIO1, GPIO6, Game Port & MIDI Port)

CR 30h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3 R / W 0: GPIO6 is inactive. 1: Activate GPIO6.

2 R / W 0: MIDI Port is inactive. 1: Activate MIDI Port.

1 R / W 0: Game Port is inactive. 1: Activate Game Port.

Publication Release Date: April 7 , 2009

-213- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

0 R / W 0: GPIO1 is inactive. 1: Activate GPIO1.

CR 60h, 61h. (Default 0 2h, 01h)

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select Game Port base address <100h : FFFh> on 1

byte boundary.

CR 62h, 63h. (Default 0 3h, 30h)

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select MIDI Port base address <100h : FFEh> on 2

bytes boundary.

CR 70h. (Default 09h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for MIDI Port.

CR F0h. (GPIO1 I/O register; Default FFh)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO1 I/O register

0: The respective GPIO1 PIN is programmed as an Output port

1: The respective GPIO1 PIN is programmed as an Input port.

CR F1h. (GPIO1 Data register; Default 00h)

BIT READ / WRITE DESCRIPTION

- 214 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

R / W

GPIO1 Data register

For Output ports, the respective bits can be read/written and produced to

pins.

7~0

Read Only For Input ports, the respective bits can be read only from pins. Write

accesses will be ignored.

CR F2h. (GPIO1 Inversion register; De fault 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO1 Inversion register

0: The respective bit and the port value are the same.

1: The respective bit and the port value are inverted. (Both Input & Output

ports)

CR F3h. (GPIO1 I/O register; Default 00h)

BIT READ / WRITE DESCRIPTION

7 R / W

0: GPIO17

1: GPIO17 Æ PLED

6 R / W

0: GPIO16

1: GPIO16 Æ WDTO#

5 R / W

0: GPIO15

1: GPIO15 Æ PLED

4 R / W

0: GPIO14

1: GPIO14 Æ WDTO#

3 R / W

0: GPIO13

1: GPIO13 Æ PLED

2 R / W

0: GPIO12

1: GPIO12 Æ WDTO#

Publication Release Date: April 7 , 2009

-215- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

1 R / W

0: GPIO11

1: GPIO11 Æ PLED

0 R / W

0: GPIO10

1: GPIO10 Æ WDTO#

CR F4h. (GPIO6 I/O register; Default FFh)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO6 I/O register

0: The respective GPIO6 PIN is programmed as an Output port

1: The respective GPIO6 PIN is programmed as an Input port.

CR F5h. (GPIO6 Data register; Default 00h)

BIT READ / WRITE DESCRIPTION

R / W

GPIO6 Data register

For Output ports, the respective bits can be read/written and produced to

pins.

7~0

Read Only For Input ports, the respective bits can be read only from pins. Write

accesses will be ignored.

CR F6h. (GPIO6 Inversion register; De fault 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO6 Inversion register

0: The respective bit and the port value are the same.

1: The respective bit and the port value are inverted. (Both Input & Output

ports)

CR F7h. (Game Port PAD control register; Default 00h)

- 216 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

Joystick Power Down

0: Joystick Power Down Disable.

1: Joystick Power Down Enable.

17.8 Logical Device 8 (WDTO# & PLED)

CR 30h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W 0: WDTO# is inactive. 1: Activate WDTO#.

CR F5h. (WDTO#, PLED and KBC P20 control mode registe r; Default 00h)

BIT READ / WRITE DESCRIPTION

7~6 R / W

Select Power LED mode.

00: Power LED pin is tri-stated.

01: Power LED pin is driven low.

10: Power LED pin outputs 1Hz pulse with 50% duty cycle.

11: Power LED pin outputs 1/4Hz pulse with 50% duty cycle.

5 Reserved.

4 R / W

Faster 1000 times for WDTO# count mode.

0: Disable.

1: Enable.

(If bit-3 is Second Mode , the count mode be 1/1000 Sec.)

(If bit-3 is Minute Mode , the count mode be 1/1000 Min.)

3 R / W

Select WDTO# count mode.

0: Second Mode.

1: Minute Mode.

Publication Release Date: April 7 , 2009

-217- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

2 R / W

Enable the rising edge of KBC reset (P20) to issue time-out event.

0: Disable.

1: Enable.

1 R / W

Disable / Enable the WDTO# output low pulse to the KBRST# pin (PIN60)

0: Disable.

1: Enable.

0 Reserved.

CR F6h. (WDTO# counter register ; Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

Watch Dog Timer Time-out value. Writing a non-zero value to this

and start counting down. If the bit 7 and 6 of CR F7h are set, any

Mouse Interrupt or Keyboard Interrupt event will also cause the reload

of previously-loaded non-zero value to Watch Dog Counter and start

counting down. Reading this register returns current value in Watch

Dog Counter instead of Watch Dog Timer Time-out value.

00h: Time-out Disable

01h: Time-out occurs after 1 second/minute

02h: Time-out occurs after 2 second/minutes

03h: Time-out occurs after 3 second/minutes

……………………….......................................

FFh: Time-out occurs after 255 second/minutes

CR F7h. (WDTO# control & status r egister; Defaul t 00h)

BIT READ / WRITE DESCRIPTION

- 218 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7 R / W

Mouse interrupt reset watch-dog timer enable

0: Watchdog timer is not affected by mouse interrupt.

1: Watchdog timer is reset by mouse interrupt.

6 R / W

Keyboard interrupt reset watch-dog timer enable

0: Watchdog timer is not affected by keyboard interrupt.

1: Watchdog timer is reset by keyboard interrupt.

5 Write “1” Only Trigger WDTO# event. This bit is self-clearing.

4 R / W

WDTO# status bit

0: Watchdog timer is running.

1: Watchdog timer issues time-out event.

3~0 R / W These bits select IRQ resource for WDTO#. (02h for SMI# event.)

17.9 Logical Device 9 (GPIO2,GPIO3, GPIO4, GPIO5 & SUSLED) (VSB Po wer)

CR 30h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3 R / W 0: GPIO5 is inactive. 1: Activate GPIO5

2 R / W 0: GPIO4 is inactive. 1: Activate GPIO4.

1 R / W 0: GPIO3 is inactive. 1: Activate GPIO3.

0 R / W 0: GPIO2 is inactive. 1: Activate GPIO2.

CR E0h. (GPIO5 I/O register; Default FFh)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO5 I/O register

0: The respective GPIO5 PIN is programmed as an Output port

1: The respective GPIO5 PIN is programmed as an Input port.

Publication Release Date: April 7 , 2009

-219- Version 1.94

W83627EHF/EF

W83627EHG

CR E1h. (GPIO5 Data register; Default 00h)

BIT READ / WRITE DESCRIPTION

R / W

GPIO5 Data register

For Output ports, the respective bits can be read/written and produced to

pins.

7~0

Read Only For Input ports, the respective bits can be read only from pins. Write

accesses will be ignored.

CR E2h. (GPIO5 Inversion register; Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO5 Inversion register

0: The respective bit and the port value are the same.

1: The respective bit and the port value are inverted. (Both Input & Output

ports)

CR E3h. (GPIO2 register; Default FFh)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO2 I/O register

0: The respective GPIO2 PIN is programmed as an Output port

1: The respective GPIO2 PIN is programmed as an Input port

CR E4h. (GPIO2 Data register; Default 00h)

BIT READ / WRITE DESCRIPTION

R / W

GPIO2 Data register

For Output ports, the respective bits can be read/written and produced to

pins.

7~0

Read Only For Input ports, the respective bits can be read only from pins. Write

accesses will be ignored.

- 220 -

W83627EHF/EF

W83627EHG/EG

CR E5h. (GPIO2 Inversion register; Default 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO2 Inversion register

0: The respective bit and the port value are the same.

1: The respective bit and the port value are inverted. (Both Input & Output

ports)

CR F0h. (GPIO3 I/O register; Default FFh)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO3 I/O register

0: The respective GPIO3 PIN is programmed as an Output port

1: The respective GPIO3 PIN is programmed as an Input port.

CR F1h. (GPIO3 Data register; Default 00h)

BIT READ / WRITE DESCRIPTION

R / W

GPIO3 Data register

For Output ports, the respective bits can be read/written and produced to

pins.

7~0

Read Only For Input ports, the respective bits can be read only from pins. Write

accesses will be ignored.

CR F2h. (GPIO3 Inversion register; De fault 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO3 Inversion register

0: The respective bit and the port value are the same.

1: The respective bit and the port value are inverted. (Both Input & Output

ports)

CR F3h. (Suspend LED mode register; Default 00h) (VBAT po wer)

Publication Release Date: April 7 , 2009

-221- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

7~6 R / W

Select Suspend LED mode.

00: Suspend LED pin is tri-stated.

01: Suspend LED pin is driven low.

10: Suspend LED pin outputs 1Hz pulse with 50% duty cycle.

11: Suspend LED pin outputs 1/4Hz pulse with 50% duty cycle.

5~0 Reserved.

CR F4h. (GPIO4 I/O register; Default FFh)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO4 I/O register

0: The respective GPIO4 PIN is programmed as an Output port

1: The respective GPIO4 PIN is programmed as an Input port.

CR F5h. (GPIO4 Data register; Default 00h)

BIT READ / WRITE DESCRIPTION

R / W

GPIO4 Data register

For Output ports, the respective bits can be read/written and produced to

pins.

7~0

Read Only For Input ports, the respective bits can be read only from pins. Write

accesses will be ignored.

CR F6h. (GPIO4 Inversion register; De fault 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W

GPIO4 Inversion register

0: The respective bit and the port value are the same.

1: The respective bit and the port value are inverted. (Both Input & Output

ports)

- 222 -

W83627EHF/EF

W83627EHG/EG

CR F7h. (GPIO4 multi-function select register; Default 00h)

BIT READ / WRITE DESCRIPTION

7 R / W

0: GPIO47

1: GPIO47 Æ SUSLED

6 R / W

0: GPIO46

1: GPIO46 Æ WDTO#

5 R / W

0: GPIO45

1: GPIO45 Æ SUSLED

4 R / W

0: GPIO44

1: GPIO44 Æ WDTO#

3 R / W

0: GPIO43

1: GPIO43 Æ SUSLED

2 R / W

0: GPIO42

1: GPIO42 Æ WDTO#

1 R / W

0: GPIO41

1: GPIO41 Æ SUSLED

0 R / W

0: GPIO40

1: GPIO40 Æ WDTO#

17.10 Logical Device A (ACPI)

(CR30, CR70 are VCC powered; CRE 0~F7 are VRTC powered)

CR 30h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

Publication Release Date: April 7 , 2009

-223- Version 1.94

W83627EHF/EF

W83627EHG

CR 70h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for PME#.

CR E0h. (Default 01h) (VBAT power)

BIT READ / WRITE DESCRIPTION

7 R / W

DIS_PSIN => Disable panel switch input to turn system power supply on.

0: PSIN is wire-AND and connected to PSOUT#.

1: PSIN is blocked and cannot affect PSOUT#.

6 R / W

Enable KBC wake-up

0: Disable keyboard wake-up function via PSOUT#.

1: Enable keyboard wake-up function via PSOUT#.

5 R / W

Enable Mouse wake-up

0: Disable mouse wake-up function via PSOUT#.

1: Enable mouse wake-up function via PSOUT#.

- 224 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

4 R / W

MSRKEY =>

3 keys (ENMDAT_UP, CRE6[7]; MSRKEY, CRE0[4]; MSXKEY, CRE0[1])

define the combinations of the mouse wake-up events. Please check out

the following table for the detailed.

ENMDAT_UP MSRKEY MSXKEY Wake-up event

1 x 1 Any button clicked or movement.

1 x 0

One click of either left or right MS

button.

0 0 1 One click of the MS left button.

0 1 1 One click of the MS right button.

0 0 0 Two clicks of the MS left button.

0 1 0 Two clicks of the MS right button.

3 Reserved.

2 R / W

Keyboard / Mouse swap enable

0: Normal mode.

1: Keyboard / Mouse ports are swapped.

1 R / W

MSXKEY =>

3 keys (ENMDAT_UP, CRE6[7]; MSRKEY, CRE0[4]; MSXKEY, CRE0[1])

define the combinations of the mouse wake-up events. Please check out

the table in CRE0[4] for the detailed.

0 R / W

KBXKEY =>

0: Only the pre-determined key combination in sequence can wake up the

system.

1: Any character received from keyboard can wake up the system.

CR E1h. (KBC Wake-Up Index Register; Default 00h) (VSB power)

Publication Release Date: April 7 , 2009

-225- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

7~0 R / W

Keyboard wake-up index register.

It is the index register of CRE2, which is the access window of keyboard

pre-determined key combination characters. The first set of wake up key

combination is in the range of 0x00 - 0x0E, the second set 0x30 – 0x3E,

and the third set 0x40 – 0x4E. Incoming key combination can be read

through 0x10 – 0x1E.

CR E2h. (KBC Wake- Up Data Register; Default ffh) (VSB power)

BIT READ / WRITE DESCRIPTION

7~0 R / W

Keyboard wake-up data register.

It is the data register of the keyboard pre-determined key combination

characters, which is indexed by CRE1.

CR E3h. (Event Status Register; Default 08h)

BIT READ / WRITE DESCRIPTION

7~6 Reserved.

Read Only

Read-Clear This event status is caused by VSB power off/on.

Read Only

Read-Clear

If E4[7] is 1 =>

This bit is 0: When power-loss occurs and VSB power is on, indicate that

turn on system power.

This bit is 1: When power-loss occurs and VSB power is on, indicate that

turn off system power.

If E4[7] is 0 => This bit is always 0.

Read Only

Read-Clear

Thermal shutdown status.

0: No thermal shutdown event issued.

1: The thermal shutdown event issued.

- 226 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

Read Only

Read-Clear

PSIN_STS

0: No PSIN event issued.

1: The PSIN event issued.

Read Only

Read-Clear

MSWAKEUP_STS => The bit is latched by the mouse wake-up event.

0: No mouse wake-up event issued.

1: The mouse wake-up event issued.

Read Only

Read-Clear

KBWAKEUP_STS => The bit is latched by the keyboard wake-up event.

0: No keyboard wake-up event issued.

1: The keyboard wake-up event issued.

CR E4h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7 R / W

Power loss control bit 2

0： Indicates that PSON#（Pin 72）outputs logic low after PSOUT# issues

a low pulse.

1： Indicates that PSON#（Pin 72）will output logic low after resume from

AC power loss if SUSB#（Pin 73）is logic high.

6~5 R / W

Power loss control bits <1：0> => (VBAT)

00: System always turns off when come back from power loss state.

01: System always turns on when come back from power loss state.

10: System turns off / on when come back from power loss state depend

on the state before power loss.

11: User define the state before power loss.(The last state set at CRE6[4])

4 Reserved

3 R / W

Keyboard wake-up options. (LRESET#)

(e) 0: Password or sequence hot keys programmed in the registers.

1: Any key.

Publication Release Date: April 7 , 2009

-227- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

2 R / W

Enable the hunting mode for all wake-up events set in CRE0. This bit is

cleared when any wake-up events is captured. (LRESET#)

0: Disable.

1: Enable.

1~0 Reserved.

CR E5h. (Reserved)

BIT READ / WRITE DESCRIPTION

7~0 Reserved.

CR E6h. (Default 1Ch)

BIT READ / WRITE DESCRIPTION

7 R / W

ENMDAT => (VSB)

3 keys (ENMDAT_UP, CRE6[7]; MSRKEY, CRE0[4]; MSXKEY, CRE0[1])

define the combinations of the mouse wake-up events. Please check out the

table in CRE0[4] for the detailed.

6 Reserved.

5 R / W

CASEOPEN Clear Control. (VSB)

Write 1 to this bit will clear CASEOPEN status. This bit won’t be self cleared,

please write 0 after event be cleared. The function is as same as Index 46h bit

7 of H/W Monitor part.

4 R / W

Power loss Last State Flag. (VBAT)

0: ON

1: OFF.

3 R / W

PWROK_DEL (first stage) (VSB)

Set the delay rising time from PWROK_LP to PWROK_ST.

0: 300 ~ 600 ms.

1: 200 ~ 300 ms.

- 228 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

2~1 R / W

PWROK_DEL (VSB)

Set the delay rising time from PWROK_ST to PWROK.

00: No delay time. 01: Delay 32 ms

10: 96 ms 11: Delay 250 ms

0 R / W-Clear

PWROK_TRIG =>

Write 1 to re-trigger POWEROK signals from low to high.

CR E7h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7 R / W

ENKD3 => (VSB)

Enable the third set of keyboard wake-up key combination. Its values are

accessed through keyboard wake-up index register (CRE1) and keyboard

wake-up data register (CRE2) at the index from 40h to 4eh.

0: Disable the third set of the key combinations.

1: Enable the third set of the key combinations.

6 R / W

ENKD2 => (VSB)

Enable the second set of keyboard wake-up key combination. Its values

are accessed through keyboard wake-up index register (CRE1) and

keyboard wake-up data register (CRE2) at the index from 30h to 3eh.

0: Disable the second set of the key combinations.

1: Enable the second set of the key combinations.

5 R / W

ENWIN98KEY => (VSB)

Enable Win98 keyboard dedicated key to wake-up system via PSOUT#

when keyboard wake-up function is enabled.

0: Disable Win98 keyboard wake-up.

1: Enable Win98 keyboard wake-up.

Publication Release Date: April 7 , 2009

-229- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

4 R / W

EN_ONPSOUT (VBAT)

Disable/Enable to issue a 0.5s long PSOUT# pulse when system returns

from power loss state and is supposed to be on as described in CRE4[6:5],

logic device A. (for SiS & VIA chipsets)

0: Disable.

1: Enable.

3 R / W

Select WDTO# reset source (VSB)

0: Watchdog timer is reset by LRESET#.

1: Watchdog timer is reset by PWROK

2~1 Reserved.

0 R / W

Hardware Monitor RESET source select (VBAT)

0: PWROK

1: LRESET#

CR E8h. (Reserved)

CR F2h. (Default 7Ch) (VSB power)

BIT READ / WRITE DESCRIPTION

7 Reserved.

6 R / W

Enable RSTOUT4# function.

0: Disable RSTOUT4#.

1: Enable RSTOUT4#.

5 R / W

Enable RSTOUT3# function.

0: Disable RSTOUT3#.

1: Enable RSTOUT3#.

4 R / W

Enable RSTOUT2# function.

0: Disable RSTOUT2#.

1: Enable RSTOUT2#.

- 230 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

3 R / W

Enable RSTOUT1# function.

0: Disable RSTOUT1#.

1: Enable RSTOUT1#.

2 R / W

Enable RSTOUT0# function.

0: Disable RSTOUT0#.

1: Enable RSTOUT0#.

1 Reserved.

0 R / W EN_PME => 0: Disable PME. 1: Enable PME.

CR F3h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~6 Reserved.

5 R / W-Clear

PME status of the Mouse IRQ event.

Write 1 to clear this status.

4 R / W-Clear

PME status of the KBC IRQ event.

Write 1 to clear this status.

3 R / W-Clear

PME status of the PRT IRQ event.

Write 1 to clear this status.

2 R / W-Clear

PME status of the FDC IRQ event.

Write 1 to clear this status.

1 R / W-Clear

PME status of the URA IRQ event.

Write 1 to clear this status.

0 R / W-Clear

PME status of the URB IRQ event.

Write 1 to clear this status.

CR F4h. (Default 00h)

BIT READ / WRITE DESCRIPTION

Publication Release Date: April 7 , 2009

-231- Version 1.94

W83627EHF/EF

W83627EHG

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3 R / W-Clear

PME status of the HM IRQ event.

Write 1 to clear this status.

2 R / W-Clear

PME status of the WDTO# event.

Write 1 to clear this status.

1 R / W-Clear

PME status of the MIDI IRQ event.

Write 1 to clear this status.

0 R / W-Clear

PME status of the RIB event.

Write 1 to clear this status.

CR F6h. (Default 00h) (VSB power)

BIT READ / WRITE DESCRIPTION

7~6 Reserved.

5 R / W

0: Disable PME interrupt of the Mouse IRQ event.

1: Enable PME interrupt of the Mouse IRQ event.

4 R / W

0: Disable PME interrupt of the KBC IRQ event.

1: Enable PME interrupt of the KBC IRQ event.

3 R / W

0: Disable PME interrupt of the PRT IRQ event.

1: Enable PME interrupt of the PRT IRQ event.

2 R / W

0: Disable PME interrupt of the FDC IRQ event.

1: Enable PME interrupt of the FDC IRQ event.

1 R / W

0: Disable PME interrupt of the URA IRQ event.

1: Enable PME interrupt of the URA IRQ event.

0 R / W

0: Disable PME interrupt of the URB IRQ event.

1: Enable PME interrupt of the URB IRQ event.

CR F7h. (Default 00h) (VSB power)

- 232 -

W83627EHF/EF

W83627EHG/EG

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3 R / W

0: Disable PME interrupt of the HM IRQ event.

1: Enable PME interrupt of the HM IRQ event.

2 R / W

0: Disable PME interrupt of the WDTO# event.

1: Enable PME interrupt of the WDTO# event.

1 R / W

0: Disable PME interrupt of the MIDI IRQ event.

1: Enable PME interrupt of the MIDI IRQ event.

0 R / W

0: Disable PME interrupt of the RIB event.

1: Enable PME interrupt of the RIB event.

17.11 Logical Device B (Hardware Monitor, for W83627EHF/EHG only)

CR 30h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~1 Reserved.

0 R / W

0: Logical device is inactive.

1: Activate the logical device.

CR 60h, 61h. (Default 0 0h, 00h)

BIT READ / WRITE DESCRIPTION

7~0 R / W These two registers select HM base address <100h : FFEh> on 2 bytes

boundary.

CR 70h. (Default 00h)

BIT READ / WRITE DESCRIPTION

7~4 Reserved.

3~0 R / W These bits select IRQ resource for HM.

Publication Release Date: April 7 , 2009

-233- Version 1.94

W83627EHF/EF

W83627EHG

CR F0h. (VID Control register; De fault C1h)

BIT READ / WRITE DESCRIPTION

7 R / W

VID I/O Control (CRF1[5:0])

0: VID output mode.

1: VID input mode.

6-0 Reserved.

CR F1h. (VID Data Regist er; Default 00h)

BIT READ / WRITE DESCRIPTION

7~6 Reserved.

5~0 R / W VID[5:0] Data Register.

- 234 -

W83627EHF/EF

W83627EHG/EG

18. SPECIFICATIONS

18.1 Absolute Maximum Ratings

SYMBOL PARAMETER RATING UNIT

3VCC Power Supply Voltage

(3.3V)

3.3V ± 5% V

Input Voltage -0.5 to 3VCC+0.5 V VI

Input Voltage (5V

tolerance)

-0.5 to 6 V

VBAT RTC Battery Voltage VBAT 2.2 to 4.0 V

TA Operating Temperature 0 to +70 °C

TSTG Storage Temperature -55 to +150 °C

Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability

of the device.

18.2 DC CHARACTERISTICS

(Ta = 0°C to 70°C, VDD = 3.3V ± 5%, VSS = 0V)

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

RTC Battery Quiescent

Current

IBAT 2.4

μA VBAT = 2.5 V

ACPI Stand-by Power

Supply Quiescent Current

ISB 2.0 mA VSB = 3.3 V, All

ACPI pins are not

connected.

I/O8t - TTL level bi-directional pin with 8mA source-sink capability

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Output Low Voltage VOL 0.4 V IOL = 8 mA

Output High Voltage VOH 2.4 V IOH = - 8 mA

Publication Release Date: April 7 , 2009

-235- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/O12t - TTL level bi-directional pin with 12mA source-sink capability

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Output High Voltage VOH 2.4 V IOH = -12 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/O24t - TTL level bi-directional pin with 24mA source-sink capability

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Output Low Voltage VOL 0.4 V IOL = 24 mA

Output High Voltage VOH 2.4 V IOH = -24 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/O12tp3 – 3.3V TTL level bi-directional pin with 12mA source-sink capability

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Output High Voltage VOH 2.4 V IOH = -12 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/O12ts - TTL level Schmitt-trigger bi-directional pin with 12mA source-sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V

- 236 -

W83627EHF/EF

W83627EHG/EG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V

Hystersis VTH 0.5 1.2 V VDD=3.3V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Output High Voltage VOH 2.4 V IOH = -12 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/O24ts - TTL level Schmitt-trigger bi-directional pin with 24mA source-sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V

Hystersis VTH 0.5 1.2 V VDD= 3.3V

Output Low Voltage VOL 0.4 V IOL = 24 mA

Output High Voltage VOH 2.4 V IOH = -24 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/O24tsp3 – 3.3V TTL level Schmitt-trigger bi-directional pin with 24mA source-sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V

Hystersis VTH 0.5 1.2 V VDD=3.3V

Output Low Voltage VOL 0.4 V IOL = 24 mA

Output High Voltage VOH 2.4 V IOH = -24 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Publication Release Date: April 7 , 2009

-237- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input Low Leakage ILIL -10

μA VIN = 0V

I/OD12t - TTL level bi-directional pin and open-drain output with 12mA sink capability

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/OD24t - TTL level bi-directional pin and open-drain output with 24mA sink capability

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Output Low Voltage VOL 0.4 V IOL = 24 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/OD12ts - TTL level Schmitt-trigger bi-directional pin and open drain output with 12m A sink

capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V

Hystersis VTH 0.5 1.2 V VDD=3.3V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/OD24ts - TTL level Schmitt-trigger bi-directional pin and open drain output with 24m A sink

capability

- 238 -

W83627EHF/EF

W83627EHG/EG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V

Hystersis VTH 0.5 1.2 V VDD=3.3V

Output Low Voltage VOL 0.4 V IOL = 24 mA

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0V

I/OD12cs - CMOS level Schmitt-trigger bi-directional pin and open drain output with 12mA

sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3 V

Hystersis VTH 0.5 1.2 V VDD = 3.3 V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

I/OD16cs - CMOS level Schmitt-trigger bi-directional pin and open drain output with 16mA

sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3 V

Hystersis VTH 0.5 1.2 V VDD = 3.3 V

Output Low Voltage VOL 0.4 V IOL = 16 mA

Input High Leakage ILIH +10

μA VIN = 3.3 V

Publication Release Date: April 7 , 2009

-239- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input Low Leakage ILIL -10

μA VIN = 0 V

I/OD12csd - CMOS level Schmitt-trigger bi-directional pin with internal pull down resistor and

open drain output with 12mA sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3 V

Hystersis VTH 0.5 1.2 V VDD = 3.3 V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

I/OD12csu - CMOS level Schmitt-trigger bi-directional pin with internal pull up resistor and

open drain output with 12mA sink capability

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3 V

Hystersis VTH 0.5 1.2 V VDD = 3.3 V

Output Low Voltage VOL 0.4 V IOL = 12 mA

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

O4 - Output pin with 4mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 4 mA

Output High Voltage VOH 2.4 V IOH = -4 mA

O8 - Output pin with 8mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 8 mA

Output High Voltage VOH 2.4 V IOH = -8 mA

- 240 -

W83627EHF/EF

W83627EHG/EG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

O12 - Output pin with 12mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 12 mA

Output High Voltage VOH 2.4 V IOH = -12 mA

O16 - Output pin with 16mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 16 mA

Output High Voltage VOH 2.4 V IOH = -16 mA

O24 - Output pin with 24mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 24 mA

Output High Voltage VOH 2.4 V IOH = -24 mA

O12p3 - 3.3V output pin with 12mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 12 mA

O24p3 - 3.3V output pin with 24mA source-sink capability

Output Low Voltage VOL 0.4 V IOL = 24 mA

OD12 - Open drain output pin with 12mA sink capability

Output Low Voltage VOL 0.4 V IOL = 12 mA

OD24 - Open drain output pin with 24mA sink capability

Output Low Voltage VOL 0.4 V IOL = 24 mA

OD12p3 - 3.3V open drain output pin with 12mA sink capability

Output Low Voltage VOL 0.4 V IOL = 12 mA

INt - TTL level input pin

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

INtp3 - 3.3V TTL level input pin

Publication Release Date: April 7 , 2009

-241- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0 V

INtd - TTL level input pin with internal pull do wn resistor

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

INtu - TTL level input pin with internal pull up resistor

Input Low Voltage VIL 0.8 V

Input High Voltage VIH 2.0 V

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

INts - TTL level Schmitt-trigger input pin

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3 V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3 V

Hystersis VTH 0.5 1.2 V VDD = 3.3 V

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

INtsp3 - 3.3 V TTL level Schmitt-trigger input pin

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3 V

- 242 -

W83627EHF/EF

W83627EHG/EG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3 V

Hystersis VTH 0.5 1.2 V VDD = 3.3 V

Input High Leakage ILIH +10

μA VIN = 3.3 V

Input Low Leakage ILIL -10

μA VIN = 0 V

INc - CMOS level input pin

Input Low Voltage VIL 1.5 V

Input High Voltage VIH 3.5 V

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0 V

INcd - CMOS level input pin with internal pull down resistor

Input Low Voltage VIL 1.5 V

Input High Voltage VIH 3.5 V

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0 V

INcs - CMOS level Schmitt-trigger input pin

Input Low Threshold

Voltage

Vt- 1.3 1.5 1.7 V VDD = 3.3V

Hystersis VTH 1.5 2 V VDD = 3.3V

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0 V

INcsu - CMOS level Schmitt-trigger input pin with internal pull up resistor

Input Low Threshold

Voltage

Vt- 0.5 0.8 1.1 V VDD = 3.3V

Input High Threshold

Voltage

Vt+ 1.6 2.0 2.4 V VDD = 3.3V

Publication Release Date: April 7 , 2009

-243- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS

Hystersis VTH 0.5 1.2 V VDD = 3.3V

Input High Leakage ILIH +10

μA VIN = 3.3V

Input Low Leakage ILIL -10

μA VIN = 0 V

18.3 AC CHARACTERISTICS

18.3.1 AC Power Failure Resume Timing

1. Logical Device A, CR[E4h] bit7 = “0” and CR[E4h] bits[6:5] are selected to “OFF” state

(“OFF” means always being turned off or the previous state is off)

3VCC

PSOUT#

PSON#

SUSB#

RSMRST#

3VSB

ACLOSS

- 244 -

W83627EHF/EF

W83627EHG/EG

2. Logical Device A, CR[E4h] bit7 = “0” and CR[E4h] bits[6:5] are selected to “ON” state

(“ON” means always being turned on or the previous state is on)

3VCC

PSOUT#

PSON#

SUSB#

RSMRST#

3VSB

ACLOSS

Publication Release Date: April 7 , 2009

-245- Version 1.94

W83627EHF/EF

W83627EHG

3. Logical Device A, CR[E4h] bit7 = “1” and CR[E4h] bits[6:5] are selected to “OFF” state

(“OFF” means always being turned off or the previous state is off)

- 246 -

W83627EHF/EF

W83627EHG/EG

4. Logical Device A, CR[E4h] bit7 = “1” and CR[E4h] bits[6:5] are selected to “ON” state

(“ON” means always being turned on or the previous state is on)

3VCC

PSOUT#

PSON#

SUSB#

RSMRST#

3VSB

ACLOSS

Publication Release Date: April 7 , 2009

-247- Version 1.94

W83627EHF/EF

W83627EHG

** What’s the definition of former state at AC power failure?

1) The previous state is “ON”

3VCC falls to 2.6V and SUSB# keeps at VIH 2.0V

3VCC

SUSB#

2) The previous state is “OFF”

3VCC falls to 2.6V and SUSB# keeps at VIL 0.8V

3VCC

SUSB#

To ensure that VCC does not fall faster than VSB in various ATX Power Supplies, the

W83627EHF/EHG/EF/EG adds the option of “user define mode” for the pre-defined state before AC

power failure. BIOS can set the pre-defined state to be “On” or “Off”. According to this setting, the

system chooses the state after the AC power recovery.

- 248 -

W83627EHF/EF

W83627EHG/EG

Logical Device A, CR E4h

6~5 R / W

Power-loss control bits => (VBAT)

00: System always turns off when it returns from power-loss state.

01: System always turns on when it returns from power-loss state.

10: System turns off / on when it returns from power-loss state depending

on the state before the power loss.

11: User defines the state before the power loss.(The previous state is set

at CRE6[4])

Logical Device A, CR E6h

4 R / W

Power loss Last State Flag. (VBAT)

0: ON

1: OFF

18.3.2 Clock Input Timing

48MHZ / 24MHZ

PARAMETER MIN MAX

UNIT

Cycle to cycle jitter 300/500 ps

Duty cycle 45 55 %

Publication Release Date: April 7 , 2009

-249- Version 1.94

W83627EHF/EF

W83627EHG

48MHZ / 24MHZ

PARAMETER DESCRIPTION MIN TYP MAX

UNIT

t1 Clock cycle time 20.8 / 41.7 ns

t2 Clock high time/low time 9 / 19 10 / 21 ns

t3 Clock rising time/falling time

(0.4V~2.4V) 3 ns

- 250 -

W83627EHF/EF

W83627EHG/EG

18.3.3 SMBus Timing

SMBCLK

SMBDAT

P S PS

TBUF

THD:STA

TLOW TR

THD:DAT

THIGH

TSU:DAT

TSU:STA TSU:STO

SYMBOL PARAMETER MIN. MAX. UNITS

TBUF Bus Free Time between Stop and

Start Condition

4.7 - uS

THD:STA Hold time after (Repeated) Start

Condition. After this period, the

first clock is generated

4.0 - uS

TSU:STA Repeated Start Condition setup

time

4.7 - uS

TSU:STO Stop Condition setup time 4.0 - uS

THD:DAT Data hold time 2.3 - uS

TSU:DAT Data setup time 0 - nS

TLOW Clock low period 4.7 - uS

THIGH Clock high period 4.0 50 uS

TF Clock/Data Falling Time - 300 nS

TR Clock/Data Rising Time - 1000 nS

Publication Release Date: April 7 , 2009

-251- Version 1.94

W83627EHF/EF

W83627EHG

18.3.4 Floppy Disk Drive Timing

FDC: Data rate = 1MB, 500KB, 300KB, 250KB/sec.

PARAMETER SYM. MIN. TYP.

(NOTE 1)

MAX. UNIT

DIR# setup time to STEP# TDST 1.0/1.6

/2.0/4.0

µS

DIR# hold time from STEP# TSTD 24/40

/48/96

µS

STEP# pulse width TSTP 6.8/11.5

/13.8/27.

7/11.7

/14/28

7.2/11.9

/14.2/28.

µS

STEP# cycle width TSC NOTE 2 NOTE 2 NOTE 2 mS

INDEX# pulse width TIDX 125/250

/417/500

RDATA# pulse width TRD 40 nS

WD# pulse width TWD 100/185

/225/475

125/210

/250/500

150/235

/275/525

Notes:

1. Typical values for T = 25°C and normal supply voltage.

2. Programmable from 0.5 mS through 32 mS as described in step rate table.

(Please refer to the description of the SPECIFY command set.)

Step Rate Table

DATA RATE

SRT

1MB/S 500KB/S 300KB/S 250KB/S

- 252 -

W83627EHF/EF

W83627EHG/EG

DATA RATE

SRT

1MB/S 500KB/S 300KB/S 250KB/S

0 8 16 26.7 32

1 7.5 15 25 30

… … … … …

E 1.0 2 3.33 4

F 0.5 1 1.67 2

Floppy Disk Driving Timing

DIR#

STEP#

INDEX#

WD#

RDATA#

TIDX

TRD

TWD

TDST TSTP TSC

TSTD

18.3.5 UART/Parallel Port

PARAMETER SYMBOL TEST

CONDITIONS

MIN. MAX. UNIT

Publication Release Date: April 7 , 2009

-253- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYMBOL TEST

CONDITIONS

MIN. MAX. UNIT

Delay from Stop to Set Interrupt TSINT 9/16 Baud

Rate

Delay from IOR Reset Interrupt TRINT 9 1000 nS

Delay from Initial IRQ Reset to

Transmit Start

TIRS 1/16 8/16 Baud

Rate

Delay from to Reset interrupt THR 175 nS

Delay from Initial IOW to interrupt TSI 9/16 16/16 Baud

Rate

Delay from Stop to Set Interrupt TSTI 8/16 Baud

Rate

Delay from IOR to Reset Interrupt TIR 8 250 nS

Delay from IOR to Output TMWO 6 200 nS

Set Interrupt Delay from Modem

Input

TSIM 18 250 nS

Reset Interrupt Delay from IOR TRIM 9 250 nS

Baud Divisor N 100 pF Loading 216-1

UART Receiver Timing

- 254 -

W83627EHF/EF

W83627EHG/EG

DATA BITS (5-8) PARITY STOP

START

TSINT

TSTI

R eceiver Timing

SIN

(RECEIVER

INPUT DATA)

IRQ

(INTERNAL SIGNAL)

IRQ#

(INTERNAL SIGNAL.

READ RECEIVER

BUFFER REGISTER)

UART Transmitter Timing

DATA BITS (5-8) PARITY STOP

(1-2)

START

TSTI

TIR

TIRS

THR

TSI THR

START

SOUT

(SER IAL O UT)

IRQ

(INTERNAL SIGNAL)

IOW#

(INTERNAL SIGNAL,

WRITE THR)

IOR#

(INTERNAL SIGNAL,

READ TIR)

18.3.5.1. Modem Control Timing

Publication Release Date: April 7 , 2009

-255- Version 1.94

W83627EHF/EF

W83627EHG

TSIM

TRIM

TMWO

TSIM

TRIM

TSIM

TMWO

START

IOW#

(INTERNAL SIGNAL,

WRITE MCR)

RTS#, DTR#

CTS#, DSR#, DCD#

IRQ

(INTERNAL SIGNAL)

IOR#

(INTERNAL SIGNAL

READ MSR)

RI#

MODEM Control Timing

18.3.6 Parallel Port Mode Parameters

PARAMETER SYM. MIN. TYP. MAX. UNIT

PD0-7, INDEX , STROBE ,

UTOFD Delay from

IOW

t1 100 nS

IRQ Delay from

CK , nFAULT t2 60 nS

IRQ Delay from IOW t3 105 nS

IRQ Active Low in ECP and EPP Modes t4 200 300 nS

ERROR Active to IRQ Active t5 105 nS

PARAMETER SYM. MIN. TYP. MAX. UNIT

PD0-7, INDEX , STROBE ,

UTOFD Delay from

IOW

t1 100 nS

IRQ Delay from

CK , nFAULT t2 60 nS

IRQ Delay from IOW t3 105 nS

IRQ Active Low in ECP and EPP Modes t4 200 300 nS

ERROR Active to IRQ Active t5 105 nS

- 256 -

W83627EHF/EF

W83627EHG/EG

18.3.7 Parallel Port

18.3.7.1. Parallel Port Timing

t3 t4

IRQ

ERROR

(ECP)

nFAULT

(ECP)

IRQ

(EPP or ECP)

IR Q (SP P )

ACK

AU T OFD , SLCTIN

PD<0:7>

IN IT , S T R OB E

IOW

18.3.7.2. EPP Data or Address Read Cycle Timing Parameters

PARAMETER SYM. MIN. MAX. UNIT

WAIT Asserted to WRITE Deasserted t14 0 185 nS

Deasserted to WRITE Modified t15 60 190 nS

WAIT Asserted to PD Hi-Z t17 60 180 nS

Command Asserted to PD Valid t18 0 nS

Command Deasserted to PD Hi-Z t19 0 nS

WAIT Deasserted to PD Drive t20 60 190 nS

Publication Release Date: April 7 , 2009

-257- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. MAX. UNIT

WRITE Deasserted to Command t21 1 nS

PBDIR Set to Command t22 0 20 nS

PD Hi-Z to Command Asserted t23 0 30 nS

Asserted to Command Asserted t24 0 195 nS

WAIT Deasserted to Command Deasserted t25 60 180 nS

Time out t26 10 12 nS

PD Valid to WAIT Deasserted t27 0 nS

PD Hi-Z to WAIT Deasserted t28 0 μS

PARAMETER SYM. MIN. MAX. UNIT

Ax Valid to IOR Asserted t1 40 nS

IOCHRDY Deasserted to IOR Deasserted t2 0 nS

IOR Deasserted to Ax Valid t3 10 10 nS

IOR Deasserted to IOW or IOR Asserted t4 40

IOR Asserted to IOCHRDY Asserted t5 0 24 nS

PD Valid to SD Valid t6 0 75 nS

IOR Deasserted to SD Hi-Z (Hold Time) t7 0 40

μS

SD Valid to IOCHRDY Deasserted t8 0 85 nS

WAIT Deasserted to IOCHRDY Deasserted t9 60 160 nS

PD Hi-Z to PDBIR Set t10 0 nS

WRITE Deasserted to IOR Asserted t13 0 nS

WAIT Asserted to WRITE Deasserted t14 0 185 nS

Deasserted to WRITE Modified t15 60 190 nS

IOR Asserted to PD Hi-Z t16 0 50 nS

WAIT Asserted to PD Hi-Z t17 60 180 nS

Command Asserted to PD Valid t18 0 nS

- 258 -

W83627EHF/EF

W83627EHG/EG

PARAMETER SYM. MIN. MAX. UNIT

Command Deasserted to PD Hi-Z t19 0 nS

WAIT Deasserted to PD Drive t20 60 190 nS

WRITE Deasserted to Command t21 1 nS

PBDIR Set to Command t22 0 20 nS

PD Hi-Z to Command Asserted t23 0 30 nS

Asserted to Command Asserted t24 0 195 nS

WAIT Deasserted to Command Deasserted t25 60 180 nS

Time out t26 10 12 nS

PD Valid to WAIT Deasserted t27 0 nS

PD Hi-Z to WAIT Deasserted t28 0 μS

18.3.7.3. EPP Data or Address Read Cycle (EPP Version 1.9)

t14 t15

t17 t18

t21

t23

t24

t27

t25

t19

t28

t20

STB# / WRITE

PD<0:7>

ADDRSTB

DATASTB

BUSY / WAIT

EPP Data or Address Read Cycle (EPP Version 1.9)

Publication Release Date: April 7 , 2009

-259- Version 1.94

W83627EHF/EF

W83627EHG

18.3.7.4. EPP Data or Address Read Cycle (EPP Version 1.7)

t14 t15

t17 t18

t21

t23

t24

t27

t25

t19

t28

t20

STB# / WRITE

PD<0:7>

ADDRSTB

DATASTB

BUSY / WAIT

EPP Data or Address Read Cycle (EPP Version 1.7)

- 260 -

W83627EHF/EF

W83627EHG/EG

18.3.7.5. EPP Data or Address Write Cycle Timing Parameters

PARAMETER SYM. MIN. MAX. UNIT

PBDIR Low to WRITE Asserted t10 0 nS

WAIT Asserted to WRITE Asserted t11 60 185 nS

WAIT Asserted to WRITE Change t12 60 185 nS

WAIT Asserted to PD Invalid t14 0 nS

PD Invalid to Command Asserted t15 10 nS

WAIT Asserted to Command Asserted t17 60 210 nS

WAIT Deasserted to Command Deasserted t18 60 190 nS

Command Asserted to WAIT Deasserted t19 0 10 μS

Time out t20 10 12 μS

Command Deasserted to WAIT Asserted t21 0 nS

PARAMETER SYM. MIN. MAX. UNIT

Ax Valid to IOW Asserted t1 40 nS

SD Valid to Asserted t2 10 nS

IOW Deasserted to Ax Invalid t3 10 nS

WAIT Deasserted to IOCHRDY Deasserted t4 0 nS

Command Asserted to WAIT Deasserted t5 10 nS

IOW Deasserted to IOW or IOR Asserted t6 40 nS

IOCHRDY Deasserted to IOW Deasserted t7 0 24 nS

WAIT Asserted to Command Asserted t8 60 160 nS

IOW Asserted to WAIT Asserted t9 0 70 nS

PBDIR Low to WRITE Asserted t10 0 nS

WAIT Asserted to WRITE Asserted t11 60 185 nS

WAIT Asserted to WRITE Change t12 60 185 nS

IOW Asserted to PD Valid t13 0 50 nS

Publication Release Date: April 7 , 2009

-261- Version 1.94

W83627EHF/EF

W83627EHG

PARAMETER SYM. MIN. MAX. UNIT

WAIT Asserted to PD Invalid t14 0 nS

PD Invalid to Command Asserted t15 10 nS

IOW to Command Asserted t16 5 35 nS

WAIT Asserted to Command Asserted t17 60 210 nS

WAIT Deasserted to Command Deasserted t18 60 190 nS

Command Asserted to WAIT Deasserted t19 0 10 μS

Time out t20 10 12 μS

Command Deasserted to WAIT Asserted t21 0 nS

IOW Deasserted to WRITE Deasserted and PD

invalid

t22 0 nS

WRITE to Command Asserted t16 5 35 nS

18.3.7.6. EPP Data or Address Write Cycle (EPP Version 1.9)

t11

STB# / WRITE

PD<0:7>

ADDRSTB

DATASTB

BUSY / WAIT

EPP Data or Address Write Cycle (EPP Version 1.9)

t10

t15

t16

t17

t19

t18

t22

t21

t12

t14

PBDIR

- 262 -

W83627EHF/EF

W83627EHG/EG

18.3.7.7. EPP Data or Address Write Cycle (EPP Version 1.7)

t11

STB# / WRITE

PD<0:7>

DATAST

ADDRSTB

BUSY / WAIT

EPP Data or Address Write Cycle (EPP Version 1.7)

t10

t15

t16

t17

t19

t18

18.3.7.8. Parallel Port FIFO Timing Parameters

PARAMETER SYMBOL MIN. MAX. UNIT

DATA Valid to nSTROBE Active t1 600 nS

nSTROBE Active Pulse Width t2 600 nS

DATA Hold from nSTROBE Inactive t3 450 nS

BUSY Inactive to PD Inactive t4 80 nS

BUSY Inactive to nSTROBE Active t5 680 nS

nSTROBE Active to BUSY Active t6 500 nS

Publication Release Date: April 7 , 2009

-263- Version 1.94

W83627EHF/EF

W83627EHG

18.3.7.9. Parallel FIFO Timing

t3 t4

PD<0:7>

STB#

BUSY

18.3.7.10. ECP Parallel Port For ward Timing Parameters

PARAMETER SYMBOL MIN. MAX. UNIT

nAUTOFD Valid to nSTROBE Asserted t1 0 60 nS

PD Valid to nSTROBE Asserted t2 0 60 nS

BUSY Deasserted to nAUTOFD Changed t3 80 180 nS

BUSY Deasserted to PD Changed t4 80 180 nS

nSTROBE Deasserted to BUSY Deasserted t5 0 nS

BUSY Deasserted to nSTROBE Asserted t6 80 200 nS

nSTROBE Asserted to BUSY Asserted t7 0 nS

BUSY Asserted to nSTROBE Deasserted t8 80 180 nS

- 264 -

W83627EHF/EF

W83627EHG/EG

18.3.7.11. ECP Parallel Port For ward Timing

nAUTOFD

PD<0:7>

STB#

BUSY

18.3.7.12. ECP Parallel Port Reverse Timing Parameters

PARAMETER SYMBOL MIN. MAX. UNIT

PD Valid to nACK Asserted t1 0 nS

nAUTOFD Deasserted to PD Changed t2 0 nS

nAUTOFD Asserted to nACK Asserted t3 0 nS

nAUTOFD Deasserted to nACK Deasserted t4 0 nS

nACK Deasserted to nAUTOFD Asserted t5 80 200 nS

PD Changed to nAUTOFD Deasserted t6 80 200 nS

18.3.7.13. ECP Parallel Port Reverse Timing

Publication Release Date: April 7 , 2009

-265- Version 1.94

W83627EHF/EF

W83627EHG

t3 t4

t5 t6

PD<0:7>

nACK

nAUTOFD

18.3.8 KBC Timing Parameters

SYMBOL DESCRIPTION MIN. MAX. UNIT

T1 Address Setup Time from WRB 0 nS

T2 Address Setup Time from RDB 0 nS

T3 WRB Strobe Width 20 nS

T4 RDB Strobe Width 20 nS

T5 Address Hold Time from WRB 0 nS

T6 Address Hold Time from RDB 0 nS

T7 Data Setup Time 50 nS

T8 Data Hold Time 0 nS

T9 Gate Delay Time from WRB 10 30 nS

T10 RDB to Drive Data Delay 40 nS

T11 RDB to Floating Data Delay 0 20 nS

T12 Data Valid After Clock Falling (SEND) 4 μS

T13 K/B Clock Period 20 μS

T14 K/B Clock Pulse Width 10 μS

- 266 -

W83627EHF/EF

W83627EHG/EG

SYMBOL DESCRIPTION MIN. MAX. UNIT

T15 Data Valid Before Clock Falling (RECEIVE) 4 μS

T16 K/B ACK After Finish Receiving 20 μS

T19 Transmit Timeout 2 mS

T20 Data Valid Hold Time 0 μS

T21 Input Clock Period (6−16 Mhz) 63 167 nS

T22 Duration of CLK inactive 30 50 μS

T23 Duration of CLK active 30 50 μS

T24 Time from inactive CLK transition, used to time when

the auxiliary device sample DATA

5 25

μS

T25 Time of inhibit mode 100 300 μS

T26 Time from rising edge of CLK to DATA transition 5 T28-5 μS

T27 Duration of CLK inactive 30 50 μS

T28 Duration of CLK active 30 50 μS

T29 Time from DATA transition to falling edge of CLK 5 25 μS

18.3.8.1. Writing Cycle Timing

T7 T8

T3T1 T5

A2, CSB

WRB

D0 ~ D7

GA20

OUTPUT

PORT

DATA IN

ACTIVE

Publication Release Date: April 7 , 2009

-267- Version 1.94

W83627EHF/EF

W83627EHG

18.3.8.2. Read Cycle Timing

T10 T11

T2 T4 T6

ACTIVE

DATA OUT

A2, CSB

AEN

RDB

D0 ~ D7

18.3.8.3. Send Data to K/B

START STOP

D0 D1 D2 D3 D4 D5 D6 D7 P

CLOCK

(KCLK)

SERIAL DATA

(KDAT)

T12 T14 T13 T26

18.3.8.4. Receive Data from K/B

T15 T14 T13

START STOP

D0 D1 D2 D3 D4 D5 D6 D7 P

CLOCK

(KCLK)

SERIAL DATA

(T1)

T20

- 268 -

W83627EHF/EF

W83627EHG/EG

18.3.8.5. Input Clock

T21

CLOCK

18.3.8.6. Send Data to Mouse

START

Bit STOP

Bit

D0 D1 D2 D3 D4 D5 D6 D7 P

MCLK

MDAT

T25 T22 T23 T24

18.3.8.7. Receive Data from Mouse

18.3.9 GPIO Timing Parameters

SYMBOL PARAMETER MIN. MAX. UNIT

Publication Release Date: April 7 , 2009

-269- Version 1.94

W83627EHF/EF

W83627EHG

tWGO Write data to GPIO update 300(Note 1) ns

tSWP SWITCH pulse width 16 msec

Note: Refer to Microprocessor Interface Timing for Read Timing.

18.3.9.1. GPIO Write Timing

A0 – A15

IOW

D0-7

GPIO 10-17

GPIO 20-25 PREVIOUS STATE

VALID

tWGO

GPIO Write Timing diagram

- 270 -

W83627EHF/EF

W83627EHG/EG

18.4 LPC Timing

PCICLK

LAD0~3,LDRQ#

(Output)

PCICLK

LPC Input Signals

Setup Time Hold

Time

SYMBOL DESCRIPTION MIN. MAX. UNIT

t1 Output Valid Delay 4 11 nS

t2 Float Delay 4 11 nS

t3 LAD[3:0] Setup Time 14 nS

t4 LAD[3:0] Hold Time 0 nS

t5 LFRAME# Setup Time 12 nS

t6 LFRAME# Hold Time 0 nS

t7 Period 30 33.3 nS

Publication Release Date: April 7 , 2009

-271- Version 1.94

W83627EHF/EF

W83627EHG

18.5 Reset Timing

LRESET#

Internal Reset

TMR

SYMBOL DESCRIPTION MIN. MAX. UNIT

TMR Internal Reset Time 30 33.3 nS

Note: The LRESET# width is dependent on the processor clock. The LRESET# must be active after the

clock is stable.

- 272 -

W83627EHF/EF

W83627EHG/EG

19. TOP MARKING SPECIFICATION

1st line: Winbond (Nuvoton) logo

2nd line: the type number: W83627EHF/EF, W83627EHG/EG (Pb-free package)

3rd line: the tracking code 030A7C282012345UA

330: packages made in '03, week 30

G: assembly house ID; G means GR, A means ASE ... etc.

9: code version; 9 means code 009

A: IC revision; A means version A, B means version B

282012345: wafer production series lot number

UB: Winbond (Nuvoton) internal use.

inbond

W83627EHF

inbond

W83627EHG

330G9A282012345UB 330G9A282012345UB

inbond inbond

330G9A282012345UB

W83627EF W83627EG

330G9A282012345UB

Publication Release Date: April 7 , 2009

-273- Version 1.94

W83627EHF/EF

W83627EHG

20. PACKAGE SPECIFICATION

0.10

0120

0.004

1.60

1.00

17.40

0.80

17.20

0.60

17.00

0.063

0.039

0.685

0.031

0.677

0.023

0.669

0.50

14.10

0.25

2.87

3.40

14.00

2.72

13.90

0.10

0.15

2.57

0.10

0.555

0.010

0.113

0.134

0.551

0.107

0.020

0.547

0.004

0.006

0.101

0.004

Symbol Min Nom Max Max

Nom

Min

Dimension in inch Dimension in mm

0.008

0.006 0.15

0.20

0.783 0.787 0.791 19.90 20.00 20.10

0.905 0.913 0.921 23.00 23.20 23.40

0.055 0.071 1.40 1.80

103

128

102

Detail F

See Detail F

Seating Plane 1

128-pin (QFP, 14x20x2.75mm foot print 3.2mm)

- 274 -

W83627EHF/EF

W83627EHG/EG

21. REVISION HISTORY

VERSION DATE PAGE DESCRIPTION

0.5 10/01/2004 N.A. 1. First published preliminary version.

0.51 11/09/2004 N.A. 1. Correct typo at 5.11.

0.52 12/07/2004 N.A.

1. Correct DC CHARACTERISTICS description

2. Update Demo Circuit

3. Add Pb-free part no:W83627EHG

0.6 03/18/2005 N.A. 1. Add SMART FANTM III description

0.61 06/10/2005 N.A. 1. Update application circuit

0.62 07/06/2005 N.A. 1. Add new part W83627EF and W83627EG.

0.63 07/19/2005 N.A.

1. Update pin configuration and application

circuit

1.0 9/13/2005 N.A.

1. Correct information and add AC Power Loss

Timing chart

1.1 02/14/2006 18 1. Correct LPT function pins description.

1.2 08/04/2006 79, 80 1. Remove “2N3904 activation” selection

1.3 10/03/2006 105, 106

1. Correct description of CRF0 of Logical Device

2/3 (UARTA/B)

1.4 10/23/2006 1, 3, 65, 70

1. Correct the description of

W83627EHF/EHG/EF/EG only supports “one”

floppy disk drive

2. Correct the Hardware Monitor Device, Bank 0,

Index 4Ah, bits[7:6]

3. Add a beep control bit for VIN4 at Hardware

Monitor Device, Bank 0, Index 57h, bit 6

Publication Release Date: April 7 , 2009

-275- Version 1.94

W83627EHF/EF

W83627EHG

VERSION DATE PAGE DESCRIPTION

1.5 04/20/2007 N.A.

1. Remove all the descriptions about Serial

Peripheral Interface functions

2. Add new chapters for Configuration Register

Access Protocol, Power Management,

Serialized IRQ, Watchdog Timer, VID Inputs

and Outputs, and PCI Reset Buffers.

3. Add new section of Conversion Sequence

and Conversion Time in Chapter 7 Hardware

Monitor.

4. Modify “Absolute Maximum Ratings” in

Chapter 18 Specifications.

5. Remove “VDD is 5V± 10% tolerance” from

the description of DC Characteristics in

Chapter 18 Specifications.

6. Update AC Timing parameters and

waveforms.

1.6 05/10/2007 N.A.

1. Correct the Data hold and setup time of

section 18.3.3 SMBus Timing

1.7 08/13/2007 40, 261, 262

1. Update the description of 7.5 Conversion

Sequence and Conversion Time.

2. Add a note to 18.5 Reset Timing.

3. Update the title of Chapter 19 from “How to

Read the Top Marking” to “Top Marking

Specification”.

1.8 08/17/2007 260, 261

1. Update 18.4 LPC Timing and 18.5 Reset

Timing

1.9 09/10/2007 85

1. Update 7.9.44 Register 50h~55h Bank

Select Register – Index 4Eh (Bank 0)

- 276 -

W83627EHF/EF

W83627EHG/EG

VERSION DATE PAGE DESCRIPTION

1.91 11/06/2007 224

1. Update “KBRST” to “KBRST#”.

2. Update the rating of 3VCC in 18.1 Absolute

Maximum Rating.

1.92 07/25/2008 10, 264

1. Update Chapter 4 Pin Configuration.

2. Move Revision History to the last chapter.

3. Change Winbond logo to Nuvoton.

1.93 08/01/2008 11-26

1. Update the descriptions of pin 13, 14, 15,

17 ,21, 22, 23, 29, 30, 51, 53, 54, 64, 69, 77,

80, 81, 89, 90, 119, and 120 -128.

1.94 04/07/2009 273

1. Update Chapter 20, package specification.

Important Notice

Nuvoton products are not designed, intended, authorized or warranted for use as components

in systems or equipment intended for surgical im plantation, atomic energy control instr uments,

airplane or spaceship instruments, transportation instruments, traffic signal instruments,

combustion control instruments, or for other applications intended to support or sustain life.

Furthermore, Nuvoton products are not intended for applications wherein failure of Nuvoton

products could result or lead to a situation wherein personal injury, death or severe property or

environmental damage could occur.

Nuvoton customers using or selling these products for use in such applications do so at their

own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper

use or sales.