CY2XF24 High Performance LVPECL Oscillator with Frequency Margining - I2C Control Features Functional Description Low jitter crystal oscillator (XO) Less than 1 ps typical root mean square (RMS) phase jitter Differential low-voltage positive emitter coupled logic (LVPECL) output The CY2XF24 is a high-performance and high-frequency XO. It uses a Cypress-proprietary low-noise PLL to synthesize the frequency from an integrated crystal. The output frequency can be changed using the I2C bus serial interface, allowing easy frequency margin testing in applications. Output frequency from 50 MHz to 690 MHz Frequency margining through I2C bus Factory-configured or field-programmable Integrated phase-locked loop (PLL) Pb-free package: 5.0 x 3.2 mm leadless chip carrier (LCC) Supply voltage: 3.3 V or 2.5 V Commercial and industrial temperature ranges The CY2XF24 is available as a factory-configured device or as a field-programmable device. Factory-configured devices are configured for general use (see "Standard and Application-Specific Factory Configurations" on page 4) or they can be customer specific. Logic Block Diagram 4 CRYSTAL OSCILLATOR LOW-NOISE PLL CLK OUTPUT DIVIDER 5 CLK# PROGRAMMABLE CONFIGURATION 1 SDA I 2C INTERFACE 2 SCL Cypress Semiconductor Corporation Document Number: 001-53146 Rev. *H * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised January 23, 2013 CY2XF24 Pinouts Figure 1. Pin Diagram - 6-pin Ceramic LCC SDA 1 SCLK 2 VSS 3 6 VDD 5 CLK# 4 CLK Table 1. Pin Definitions Pin Name I/O Type 1 SDA I/O I2C serial data 2 SCLK CMOS input I2C serial clock 4, 5 CLK, CLK# LVPECL output 6 VDD Power Supply voltage: 2.5 V or 3.3 V 3 VSS Power Ground Document Number: 001-53146 Rev. *H Description Differential output clock Page 2 of 17 CY2XF24 Contents Standard and Application-Specific Factory Configurations .................................................... 4 Functional Description ..................................................... 4 Configuration Software .................................................... 4 Programming Description ............................................... 4 Field-Programmable CY2XF24F ................................. 4 Factory-Configured CY2XF24 ..................................... 5 Programming Variables ................................................... 5 Output Frequencies ..................................................... 5 Industrial versus Commercial Device Performance .... 5 Memory Map ...................................................................... 5 Serial Interface Protocol and Timing ........................... 5 Device Address ........................................................... 5 Data Valid .................................................................... 5 Data Frame ................................................................. 6 Acknowledge Pulse ..................................................... 6 Write Operations ............................................................... 6 Writing Individual Bytes ............................................... 6 Writing Multiple Bytes .................................................. 6 Read Operations ............................................................... 6 Current Address Read ................................................. 6 Document Number: 001-53146 Rev. *H Random Read ............................................................. 6 Sequential Read .......................................................... 6 Absolute Maximum Conditions ....................................... 8 Operating Conditions ....................................................... 8 DC Electrical Characteristics .......................................... 8 AC Electrical Characteristics .......................................... 9 I2C Bus Timing Specifications ...................................... 10 Typical Output Characteristics ..................................... 10 Measurement Definitions ............................................... 12 Termination Circuits ....................................................... 12 Ordering Information ...................................................... 13 Possible Configurations ............................................. 13 Package Drawings and Dimensions ............................. 14 Acronyms ........................................................................ 15 Document Conventions ................................................. 15 Units of Measure ....................................................... 15 Document History Page ................................................. 16 Sales, Solutions, and Legal Information ...................... 17 Worldwide Sales and Design Support ....................... 17 Products .................................................................... 17 PSoC Solutions ......................................................... 17 Page 3 of 17 CY2XF24 Standard and Application-Specific Factory Configurations Part Number CY2XF24LXI009T Output Frequency Frequency Word 100 MHz (default) 156.25 MHz 350 MHz 400 MHz 0 1 2 3 Functional Description RMS Phase Jitter (Random) Offset Range Jitter (Typical) 12 kHz to 20 MHz 12 kHz to 20 MHz 12 kHz to 20 MHz 12 kHz to 20 MHz 0.85 ps 0.76 ps 0.71 ps 0.69 ps Figure 2. Frequency Words The CY2XF24 is a PLL-based high-performance clock generator. It uses an internal crystal oscillator as a reference, and outputs one differential LVPECL clock. It has an I2C bus serial interface[1], which is used to change the output frequency. The CY2XF24 comes configured for four different frequencies. At power-on, the four configurations are transparently loaded into an internal volatile memory which, in turn, controls the PLL. You can switch between the four frequencies through the I2C bus. You can also configure the CY2XF24 with new output frequencies by shifting new data into the internal memory. Frequency margining is a common application for this feature. One frequency is used for the standard operating mode of the device, while additional frequencies are available for margin testing, either during product development or in-system manufacturing test. Note that all configuration changes made using I2C are temporary and are lost when power is removed from the device. At power-on, the device returns to its original state. The configuration for a particular frequency is stored in a 6-byte block of memory, known as a word. The CY2XF24 has four such words, labeled `Frequency Word 0' through `Frequency Word 3'. An additional register byte contains a 2-bit field, which selects one of the four frequency words. By writing to this Select Byte, you can switch back and forth between the four programmed frequencies. The select byte can be configured to select any of the four frequency words at power-on. When changing the output frequency, the frequency transition is not guaranteed to be smooth. There can be frequency excursions beyond the start frequency and the new frequency. Glitches and runt pulses are possible, and time must be allowed for the PLL to relock. I2 If more than four frequencies are needed, the C bus can be used to change any of the four frequency words. When writing frequency words through I2C, you should not change the currently selected word. Instead, write one of the three unselected words before changing the select byte to select that new word. Figure 2 shows how the frequency words are arranged and selected. Register Address 10h - 15h Frequency Word 0 00 16h - 1Bh Frequency Word 1 01 1Ch - 21h Frequency Word 2 10 22h - 27h Frequency Word 3 Control PLL 11 Sel 40h Select Byte Bits [1:0] Configuration Software Cypress provides CyClockWizardTM software that enables the users to create data values for shifting into the frequency words. This software is required because the algorithm is too complicated to be described here. The user specifies the output frequency. The software then calculates the bit stream for up to four frequency words, as outlined by the register addresses for each word seen in Figure 2. Programming Description The CY2XF24 is a programmable device. Before being used in an application, it must be programmed with the output frequencies and other variables described in Programming Variables on page 5. Two different device types are available, each with its own programming flow. They are described in the following section. Field-Programmable CY2XF24F Field programmable devices are shipped unprogrammed and must be programmed before being installed on a printed circuit board (PCB). Customers use CyClockWizardTM Software to specify the device configuration and generate a joint electron devices engineering council (JEDEC - extension .jed) programming file. Programming of samples and prototype quantities is available using the CyClockWizard software along with a CY3675-CLKMAKER1 CyClockMaker Clock Programmer Kit with a CY3675-LCC6A socket adapter. Cypress's value added distribution partners also provide programming services. Field programmable devices are designated with an `F' in the part number. They are intended for quick prototyping and inventory reduction. The software and programmer kit hardware can be downloaded from www.cypress.com by clicking the hyperlinks above. Note 1. The serial interface is I2C Bus compliant, with the following exceptions: SDA input leakage current, SDA input capacitance, SDA and SCLK are clamped to VDD, setup time, and output hold time. Document Number: 001-53146 Rev. *H Page 4 of 17 CY2XF24 Factory-Configured CY2XF24 For ready-to-use devices, the CY2XF24 is available with no field programming required. Pre-configured devices (see "Standard and Application-Specific Factory Configurations" on page 4) are available for samples or orders, or a request for a custom configuration can be made. All requests are submitted to the local Cypress field application engineer (FAE) or sales representative. After the request is processed, the user receives a new part number, samples, and datasheet with the programmed values. This part number is used for additional sample requests and production orders. The CY2XF24 is one-time programmable (OTP). Programming Variables Output Frequencies The CY2XF24 is programmed with up to four independent output frequencies, which are then selected using the I2C interface. The device can synthesize frequencies to a resolution of 1 part per million (ppm), but the actual accuracy of the output frequency is limited by the accuracy of the integrated reference crystal. The CY2XF24 has an output frequency range of 50 MHz to 690 MHz, but the range is not continuous. The CY2XF24 cannot generate frequencies in the ranges of 521 MHz to 529 MHz, and 596 MHz to 617 MHz. Industrial versus Commercial Device Performance Industrial and commercial devices have different internal crystals. They have a potentially significant impact on performance levels for applications requiring the lowest possible phase noise. CyClockWIzard software allows the user to select between and view the expected performance of both options. Table 2. Device Programming Variables word is also valid for any of the other words, and produce the same frequency. The fifth field is the select byte, located at byte address 40h. The value written into the two least significant bits determines the active frequency word. The other bits of the byte are reserved and must be written with the values indicated in the table. The users should never write to any address other than the 25 bytes described here. Table 3. Frequency Words Frequency Word 0 1 2 3 Byte Addresses (hex) 10h to 15h 16h to 1Bh 1Ch to 21h 22h to 27h Word Select (Select Byte 40h) 00 01 10 11 Table 4. Register 40h: Select Byte Bits 7:2 1:0 Default Value Name Description (binary) 000000 Reserved Reserved. Always write this value UserWord Selects the Frequency Word to defined Select determine the output frequency. 00 selects Word 0; 01 selects Word 1; 10 selects Word 2; 11 selects Word 3 Serial Interface Protocol and Timing The CY2XF24 uses pins SDA and SCLK for an I2C bus that operates up to 100 kbits/sec in read or write mode. The CY2XF24 is always a slave on this bus, meaning that it never initiates a bus transaction. The basic write protocol is as follows: Output frequency 2 Start Bit; 7-bit Device Address (DA); R/W Bit; Slave Clock Acknowledge (ACK); 8-bit Memory Address (MA); ACK; 8-bit Data; ACK; 8-bit Data in MA+1 if desired; ACK; 8-bit Data in MA+2; ACK; and so on, until STOP Bit. The basic serial format is illustrated in Figure 4 on page 7. Output frequency 3 Device Address Temperature range (commercial or industrial) The device I2C address is a 7-bit value. The default I2C address, which appears in CyClockWizard is 69H, which can be changed to any other value while generating configuration using CyClockWizard. Note that the Field Programmable (unprogrammed[2]) devices has default address as 59H. Variable Output frequency 0 Output frequency 1 Memory Map Five fields can be written through the I2C bus. Four frequency words define the output frequency. As shown in Table 3, each of these words is a 6-byte field. When writing to a frequency word, all six bytes should be written. They may be written either as individual byte writes, or as a block write. The currently selected frequency word should not be written to. All four words are symmetrical, meaning that a 6-byte value that is valid for one Data Valid Data is valid when the clock is HIGH, and may only be transitioned when the clock is LOW as illustrated in Figure 5 on page 7. Note 2. Field programmable devices are shipped unprogrammed and must be programmed before being installed on a PCB. An unprogrammed device will output the crystal frequency of the integrated crystal (25 MHz for commercial and 38.8 MHz for industrial). Document Number: 001-53146 Rev. *H Page 5 of 17 CY2XF24 Data Frame Current Address Read Every new data frame is indicated by a start and stop sequence, as illustrated in Figure 6 on page 7. The CY2XF24 has an onboard address counter that retains 1 more than the address of the last word access. If the last word written or read was word `n', then a current address read operation would return the value stored in location `n+1'. When the CY2XF24 receives the slave address with the R/W bit set to a `1', the CY2XF24 issues an acknowledge and transmits the 8-bit word. The master device does not acknowledge the transfer, but does generate a STOP condition, which causes the CY2XF24 to stop transmission. START sequence - Start frame is indicated by SDA going LOW when SCLK is HIGH. Every time a start signal is given, the next 8-bit data must be the device address (seven bits) and a R/W bit, followed by register address (eight bits) and register data (eight bits). STOP sequence - Stop frame is indicated by SDA going HIGH when SCLK is HIGH. A stop frame frees the bus for writing to another part on the same bus or writing to another random register address. Acknowledge Pulse During write mode, the CY2XF24 responds with an Acknowledge (ACK) pulse after every eight bits. This is accomplished by pulling the SDA line LOW during the N*9th clock cycle as illustrated in Figure 7 on page 8. (N = the number of bytes transmitted). After the data packet is sent during read mode, the master generates the acknowledge. Write Operations Writing Individual Bytes A valid write operation must have a full 8-bit register address after the device address word from the master, which is followed by an acknowledge bit from the slave (SDA = 0/LOW). The next eight bits must contain the data word intended for storage. After the data word is received, the slave responds with another acknowledge bit (SDA = 0/LOW), and the master must end the write sequence with a STOP condition. Writing Multiple Bytes To write more than one byte at a time, the master does not end the write sequence with a stop condition. Instead, the master can send multiple contiguous bytes of data to be stored. After each byte, the slave responds with an acknowledge bit, just like after the first byte, and accept data until the acknowledge bit is responded to by the STOP condition. When receiving multiple bytes, the CY2XF24 internally increments the register address. Random Read Through random read operations, the master may access any memory location. To perform this type of read operation, first the word address must be set. This is accomplished by sending the address to the CY2XF24 as part of a write operation. After the word address is sent, the master generates a START condition following the acknowledge. This terminates the write operation before any data is stored in the address, but not before the internal address pointer is set. Next the master reissues the control byte with the R/W byte set to `1'. The CY2XF24 then issues an acknowledge and transmits the 8-bit word. The master device does not acknowledge the transfer, but does generate a STOP condition which causes the CY2XF24 to stop transmission. Sequential Read Sequential read operations follow the same process as random reads except that the master issues an acknowledge instead of a STOP condition after transmission of the first 8-bit data word. This action results in an incrementing of the internal address pointer, and subsequently output of the next 8-bit data word. By continuing to issue acknowledges instead of STOP conditions, the master may serially read the entire contents of the slave device memory. When the internal address pointer points to the FFh register, after the next increment, the pointer points to the 00h register. Read Operations Read operations are initiated the same way as write operations except that the R/W bit of the slave address is set to `1' (HIGH). There are three basic read operations: current address read, random read, and sequential read. Figure 3. Data Transfer Sequence on the Serial Bus SCLK SDA START Condition Address or Acknowledge Valid Document Number: 001-53146 Rev. *H Data may be changed STOP Condition Page 6 of 17 CY2XF24 Figure 4. Data Frame Architecture SDA Write Multiple Contiguous Registers 1 Bit Slave ACK 1 Bit 1 Bit Slave ACK R/W = 0 7-bit Device Address 8-bit Register Address (XXH) 1 Bit Slave ACK 8-bit Register Data (XXH) 1 Bit Slave ACK 8-bit Register Data (XXH+1) 1 Bit Slave ACK 8-bit Register Data (XXH+2) 1 Bit Slave ACK 8-bit Register Data (FFH) 1 Bit Slave ACK 1 Bit Slave ACK 8-bit Register Data (00H) Stop Signal Start Signal SDA Read Current Address Read Start Signal SDA Read Multiple Contiguous Registers 1 Bit Slave ACK 1 Bit 1 Bit Slave R/W = 1 ACK 7-bit Device Address 1 Bit Master ACK 8-bit Register Data Stop Signal 1 Bit Slave ACK 1 Bit 1 Bit Slave R/W = 0 ACK 7-bit Device Address 8-bit Register Address (XXH) 1 Bit Master ACK 7-bit Device Address +R/W=1 1 Bit Master ACK 8-bit Register Data (XXH) 1 Bit Master ACK 8-bit Register Data (XXH+1) 1 Bit Master ACK 8-bit Register Data (FFH) 1 Bit Master ACK 1 Bit Master ACK 8-bit Register Data (00H) Stop Signal Start Signal Repeated Start bit Figure 5. Data Valid and Data Transition Periods Data Valid Transition to next Bit SDA tDH tSU CLKHIGH VIH SCLK VIL CLKLOW Figure 6. Start and Stop Frame SDA START Document Number: 001-53146 Rev. *H Transition to next Bit SCLK STOP Page 7 of 17 CY2XF24 Figure 7. Frame Format (Device Address, R/W, Register Address, Register Data) SDA + START DA6 DA5 DA0 + R/W ACK RA7 + RA6 RA1 RA0 ACK D7 D6 + + D1 D0 ACK STOP + SCLK Absolute Maximum Conditions Parameter Description Condition Min Max Unit -0.5 4.4 V Relative to VSS -0.5 VDD+0.5 V Non Operating -55 135 C -40 135 C 2000 - V VDD Supply voltage VIN[3] Input voltage, DC TS Temperature, storage TJ Temperature, junction ESDHBM Electrostatic discharge (ESD) protection human body model (HBM) JEDEC STD 22-A114-B JA[4] Thermal resistance, junction to ambient 0 m/s airflow 64 C/W Operating Conditions Parameter VDD Min Typ Max Unit 3.3-V supply voltage range Description 3.135 3.3 3.465 V 2.5-V supply voltage range 2.375 2.5 2.625 V TPU Power-up time for VDD to reach minimum specified voltage (power ramp is monotonic) 0.05 - 500 ms TA Ambient temperature (commercial) 0 - 70 C -40 - 85 C Condition Min Typ Max Unit VDD = 3.465 V, CLK = 150 MHz, output terminated - - 150 mA VDD = 2.625 V, CLK = 150 MHz, output terminated - - 145 mA Ambient temperature (industrial) DC Electrical Characteristics Parameter IDD[5] Description Operating supply current VOH LVPECL high output voltage VDD = 3.3 V or 2.5 V, RTERM = 50 to VDD - 1.15 VDD - 2.0 V - VDD - 0.75 V VOL LVPECL low output voltage VDD = 3.3 V or 2.5 V, RTERM = 50 to VDD - 2.0 V VDD - 2.0 - VDD - 1.625 V VOD1 LVPECL output voltage swing (VOH - VOL) VDD = 3.3 V or 2.5 V, RTERM = 50 to VDD - 2.0 V 600 - 1000 mV VOD2 LVPECL output voltage swing (VOH - VOL) VDD = 2.5 V, RTERM = 50 to VDD - 1.5 V 500 - 1000 mV VOCM LVPECL output common mode voltage (VOH + VOL)/2 VDD = 2.5 V, RTERM = 50 to VDD - 1.5 V 1.2 - - V Notes 3. The voltage on any input or I/O pin cannot exceed the power pin during power-up. 4. Simulated. The board is derived from the JEDEC multilayer standard. It measures 76 x 114 x 1.6 mm and has 4-layers of copper (2/1/1/2 oz.). The internal layers are 100% copper planes, while the top and bottom layers have 50% metalization. No vias are included in the model. 5. IDD includes ~24 mA of current that is dissipated externally in the output termination resistors. Document Number: 001-53146 Rev. *H Page 8 of 17 CY2XF24 DC Electrical Characteristics (continued) Parameter Description Condition Min Typ Max Unit - - 0.1*VDD V 0.7*VDD - - V - - 0.3*VDD V - - 115 A VOLS Output low voltage (SDA) VIH Input high voltage VIL Input low voltage IIH0 Input high current (SDA) IIH1 Input high current (SCLK) Input = VDD - - 10 A IIL0 Input low current (SDA) Input = VSS -50 - - A IIL1 Input low current (SCLK) Input = VSS -20 - - A CIN0[6] Input capacitance (SDA) - 15 - pF CIN1[6] Input capacitance (SCLK) - 4 - pF Min Typ Max Unit 50 - 690 MHz IOL = 4 mA Input = VDD AC Electrical Characteristics[6] Parameter Description Condition FOUT Output frequency[7] FSC Frequency stability, commercial devices[8] TA = 0 C to 70 C - - 35 ppm FSI Frequency stability, industrial devices[8] TA = -40 C to 85 C - - 55 ppm AG Aging, 10 years - - 15 ppm TDC Output duty cycle F <= 450 MHz, measured at zero crossing 45 50 55 % F > 450 MHz, measured at zero crossing 40 50 60 % 0.2 0.4 1.0 ns TR, TF Output rise and fall time 20% and 80% of full output swing TLOCK Startup time Time for CLK to reach valid frequency measured from the time VDD = VDD(min) - - 10 ms TLSER Relock time Time for CLK to reach valid frequency from serial bus change to select bits in register 40h, measured from I2C STOP - - 10 ms TJitter() RMS phase jitter (random) FOUT = 106.25 MHz (12 kHz to 20 MHz) - 1 - ps Pre-defined factory configurations[9] See Note 9 ps Notes 6. Not 100% tested, guaranteed by design and characterization. 7. This parameter is specified in CyClockMaker software. 8. Frequency stability is the maximum variation in frequency from F0. It includes initial accuracy, plus variation from temperature and supply voltage. 9. Typical phase noise specs for factory programmed devices are listed in the table "Standard and Application-Specific Factory Configurations" on page 4. Document Number: 001-53146 Rev. *H Page 9 of 17 CY2XF24 I2C Bus Timing Specifications The I2C Bus Timing Specifications for part CY2XF24 are as follows [10] Parameter Description fSCLK SCLK frequency tHD:STA Start mode time from SDA LOW to SCLK LOW tLOW SCLK LOW period tHIGH SCLK HIGH period tSU:DAT Input data setup (SDA transition to SCLK rising edge) tHD:DAT Input data hold (SCLK falling edge to SDA transition) tHD:DO Output data hold (SCLK falling edge to SDA transition) tSR tSF tSU:STO Stop mode time from SCLK HIGH to SDA HIGH tBUF Stop mode to Start mode Min Max Unit - 100 kHz 4 - s 4.7 - s 4 - s 1000 - ns 0 - ns 200 - ns Rise time of SCLK and SDA - 300 ns Fall time of SCLK and SDA - 300 ns 4 - s 4.7 - s Typical Output Characteristics Figure 8. 2.5-V Supply and Termination to VDD-1.5 V, minimum VDD and maximum TA 0.9 1.40 0.8 0.7 VOCM (V) Swing (V) 1.35 0.6 1.30 1.25 0.5 1.20 0.4 0 100 200 300 400 500 600 Frequency (MHz) 700 0 100 200 300 400 500 600 700 Frequency (MHz) Note 10. Not 100% tested, guaranteed by design and characterization. Document Number: 001-53146 Rev. *H Page 10 of 17 CY2XF24 Figure 9. 2.5-V Supply and Termination to VDD-2 V, minimum VDD and maximum TA 0.9 0.90 0.8 0.7 VOCM (V) Swing (V) 0.85 0.6 0.80 0.75 0.5 0.4 0.70 0 100 200 300 400 500 600 700 0 100 200 Frequency (MHz) 300 400 500 600 700 Frequency (MHz) Figure 10. 3.3-V Supply and Termination to VDD-2 V, minimum VDD and maximum TA 0.9 1.60 0.8 0.7 VOCM (V) Swing (V) 1.55 0.6 1.50 1.45 0.5 0.4 1.40 0 100 200 300 400 Frequency (MHz) Document Number: 001-53146 Rev. *H 500 600 700 0 100 200 300 400 500 600 700 Frequency (MHz) Page 11 of 17 CY2XF24 Measurement Definitions Figure 11. Output DC Parameters VA CLK VOD VOCM = (V A + VB)/2 CLK# VB Figure 12. Duty Cycle Timing CLK TDC = TPW TPERIOD CLK# TPW TPERIOD Figure 13. Output Rise and Fall Time CLK# CLK 80% 80% 20% 20% TR TF Termination Circuits Figure 14. LVPECL Termination VDD - 2V (VDD = 3.3V) CLK# Document Number: 001-53146 Rev. *H CLK BUF BUF CLK VDD - 2V or VDD - 1.5V (VDD = 2.5V) CLK# Page 12 of 17 CY2XF24 Ordering Information Part Number Configuration Package Description Product Flow Pb-free CY2XF24FLXCT CY2XF24FLXIT CY2XF24LXI009T [11] Field-programmable 6-pin ceramic LCC surface mount device (SMD) - tape and reel Commercial, 0 C to 70 C Field-programmable 6-pin ceramic LCC SMD - tape and reel Industrial, -40 C to 85 C Factory-Configured 6-pin ceramic LCC SMD - tape and reel Industrial, -40 C to 85 C Some product offerings are factory-programmed customer-specific devices with customized part numbers. The Possible Configurations table shows the available device types, but not complete part numbers. Contact your local Cypress FAE or sales representative for more information. Possible Configurations Part Number[12] Configuration Package Description Product Flow Pb-free CY2XF24LXCxxxT Factory-configured 6-pin ceramic LCC SMD - tape and reel Commercial, 0 C to 70 C CY2XF24LXIxxxT Factory-configured 6-pin ceramic LCC SMD - tape and reel Industrial, -40 C to 85 C Ordering Code Definitions CY 2XF24 F LX C/I XXX T Tape and Reel Custom part configuration code C = Commercial I = Industrial 6-pin LCC package Field programmable device Base part number Company ID : CY = Cypress Notes 11. Device configuration details are described in the table "Standard and Application-Specific Factory Configurations" on page 4. 12. "xxx" indicates factory programmed parts based on customer specific configuration. For more details, contact your local Cypress FAE or Sales Representative. Document Number: 001-53146 Rev. *H Page 13 of 17 CY2XF24 Package Drawings and Dimensions Figure 15. 6-Pin 3.2 x 5.0 mm Ceramic LCC LZ06A 001-10044 *B . Document Number: 001-53146 Rev. *H Page 14 of 17 CY2XF24 Acronyms Document Conventions Table 5. Acronyms Used in this Document Units of Measure Acronym Description Symbol Unit of Measure ESD electrostatic discharge % percent FAE field application engineer C degree Celsius HBM human body model kHz kilohertz JEDEC joint electron devices engineering council mA milliampere LCC leadless chip carrier MHz megahertz LVDS Low-voltage differential signaling mm millimeter OE output enable ms millisecond PCB printed circuit board mV millivolt PLL phase-locked loop ns nanosecond RMS root mean square pF picofarad XO crystal oscillator ppm parts per million ps picosecond V volt ohms W watt A microampere s microsecond Document Number: 001-53146 Rev. *H Page 15 of 17 CY2XF24 Document History Page Document Title: CY2XF24 High Performance LVPECL Oscillator with Frequency Margining - I2C Control Document Number: 001-53146 Revision ECN Orig. of Change Submission Date ** 2704379 KVM/PYRS 05/11/09 *A 2718898 WWZ 06/15/09 Minor ECN to post datasheet to external web *B 2761926 KVM 09/10/09 Revised maximum output rise and fall times *C 2896548 KVM 03/19/10 Moved parts with `xxx' into new table, Possible Configurations Updated package diagram *D 2973338 CXQ 07/08/10 Added Standard and Application-Specific Factory Configurations table on page 2. Added phase jitter specs for pre-defined configurations into the AC Electrical Specifications table (note 8 refers users to the new table on page 2 for typical specs). Added CY2XF24LXI625T device to the Ordering Information table and added note 9 to reference the configuration description of the new device. Changed all references to CyberClocksOnline software to CyClockWizard. Removed section on phase noise vs jitter SW optimization. Changed description of Word Select feature from default Word 0 to user-defined. *E 3183855 BASH 05/06/11 Updated template as per current Cypress standards. Added Units table. Changed status from Preliminary to Final. *F 3373963 PURU 09/21/11 Updated Standard and Application-Specific Factory Configurations on page 4 and Package Drawings and Dimensions on page 14. Added new MPN CY2XF24LXI009T. *G 3514245 PURU *H 3847770 AJU Description of Change New datasheet 02/01/2012 Updated Device Address and added note 2. Updated Package Drawings and Dimensions. 01/23/2013 Updated Standard and Application-Specific Factory Configurations: Removed CY2XF24LXI625T related information. Updated Ordering Information: Removed prune part CY2XF24LXI625T. Document Number: 001-53146 Rev. *H Page 16 of 17 CY2XF24 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/memory cypress.com/go/image cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless (c) Cypress Semiconductor Corporation, 2009-2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress' product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-53146 Rev. *H Revised January 23, 2013 All products and company names mentioned in this document may be the trademarks of their respective holders. Page 17 of 17