TECHNICAL NOTE Serial-in / Parallel-out Driver Series Serial / Parallel 2-input Driver BU2098F, BU2090F/FS Description Serial-in-parallel-out driver is a open drain output driver. It incorporates a built-in shift register and a latch circuit to turn on a maximum of 12 LED by a 2-line interface, linked to a microcontroller. A open drain output provides maximum of 25mA current. Features 1) LED can be driven directly. (Output current 25mA) 2) 8/12 Bit parallel output 3) This product can be operated on low voltage. 2 4) Compatible with I C BUS. (BU2098) 2 * I C BUS is a registered trademark of Phillips. Use For AV equipment such as, audio stereo sets, videos and TV sets, PCs, control microcontroller mounted equipment. ver.C Oct.2007 Line up Parameter BU2098F BU2090F BU2090FS Output current 25 25 mA Output line 8 12 lines Package SOP16 SOP16 Unit SSOP-A16 700 700 Pd [mW] 600 Pd [mW] 600 Power dissipation 400 Power dissipation Thermal derating curve 400 500 BU2098F 300 200 100 BU2090FS 500 BU2090F 300 200 100 85 0 25 50 75 100 125 150 0 175 25 Ambient temperature Ta [] 50 75 100 125 175 150 Ambient temperature Ta [] Electrical characteristics BU2098F (unless otherwise noted, VDD=5V, Vss=0V, Ta=25) Parameter Symbol Min. Typ. Max. Unit Condition Input High-level voltage VIH 0.7VDD - - V Input Low-level voltage VIL - - 0.3VDD V Output Low-level voltage VOL - - 0.4 V Input Low-level current IIL - 2.0 A VIN=0 Input High-level current IIH - - -2.0 A VIN=VDD Output leakage current IOZ - - 5.0 A IOUT=10mA Output=High impedance VOUT=VDD Static dissipation current IDD - - 2.0 A BU2090F/FS (unless otherwise noted, VDD=5V/3V, VSS=0V, Ta=25) Parameter Symbol Min. Typ. Max. Unit Input High-level voltage VIH 3.5/2.5* - - V Input Low-level voltage VIL - - 1.5/0.4* V Output Low-level voltage VOL - - 2.0/1.0* V "H" output disable current IOZH - - 10 A VO=25V "L" output disable current IOZL - -5.0 A VO=0V IDD - 5.0/3.0* A Static dissipation current - Condition IOL=20mA (*the value at 5V /3V) 2/15 Operating conditions (Ta=25, VSS=0V) Limits Parameter Symbol Unit BU2098F Power Supply Voltage VDD Output Voltage Vo BU2090F/FS +2.75.5 0+15 V 0+25 V Absolute maximum ratings BU2098F Limits Parameter Symbol Unit BU2098F Power supply voltage VDD Power dissipation Pd -0.5+7.0 300 V * mW Operating temperature range Topr -40+85 Storage temperature range Tstg -55+125 Output voltage Vo VSS+18.0 V Input voltage VIN -0.5VDD+0.5 V Allowable loss of single unit * Reduced by 3mW/ over 25. (BU2098F) BU2090F/FS Limits Parameter Symbol Unit BU2090F Power supply voltage VDD Power dissipation 1 Pd1 BU2090FS -0.3+7.0 V 1 500 *2 mW 3 4 mW 300 * Power dissipation 2 Pd2 500 * 650 * Operating temperature range Topr -40+85 Storage temperature range Tstg -55+125 Output voltage Vo VSS-0.3+25 V Input voltage VIN VSS-0.3VDD+0.3 V Allowable loss of single unit *1 Reduced by 3mW/ over 25. *2 Reduced by 5mW/ over 25. *3 Reduced by 5.0mW for each increase in Ta of 1 over 25.(When mounted on a board 70mmx70mmx1.6mm Glass-epoxy PCB) *4 Reduced by 6.5mW for each increase in Ta of 1 over 25.(When mounted on a board 70mmx70mmx1.6mm Glass-epoxy PCB) 3/15 Pin descriptions BU2098F PIN No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pin Name A0 A1 A2 Q0 Q1 Q2 Q3 VSS Q4 Q5 Q6 Q7 N.C. SCL SDA VDD BU2090F/FS PIN No. Pin Name 1 VSS 2 DATA 3 CLOCK 4 5 6 7 8 9 10 11 12 13 14 15 16 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 VDD I/O I I I Function Address input, internally pull-up O Open drain output - GND O Open drain output I I/O - Non connected Serial clock input Serial data input/output Power supply I/O I Function GND Serial data input Data shift clock input (rising edge trigger) The shift data is transferred to the output when the input data logic level is high during the falling transition of the clock pulse. I Parallel data output (Nch Open Drain FET) O - Latch data L H Output FET ON OFF Power supply 4/15 Block diagram BU2098F Power-On Reset SDA SCL 8bit I2C Bus A0 Controller L a t c h Write Buffer Q0Q7 Shift A1 Register A2 BU2090F/FS CLOCK 12bit Controller Shift DATA Register 5/15 L a t c h Write Buffer Q0Q11 Interfaces BU2090F/FS BU2090F/FS DATA, CLOCK Q0Q11 VDD VDD OUT IN GND (VSS) GND (VSS) GND (VSS) BU2098F BU2098F Q0Q7 A0A2 VDD VDD VDD OUT IN GND (VSS) GND (VSS) GND (VSS) BU2098F BU2098F SDA SCL GND (VSS) VDD VDD IN IN GND (VSS) GND (VSS) GND (VSS) GND (VSS) 6/15 GND (VSS) BU2098F AC characteristics (Unless otherwise noted, VDD=5V, VSS=0V, Ta=25) Fast mode I2Cbus Parameter Standard mode I2Cbus Symbol Unit Min. Max. Min. Max. SCL clock frequency fSCL 0 400 0 100 kHz Bus free time between start-stop condition tBUS 1.3 - 4.7 - s tHD:STA 0.6 - 4.0 - s Low period of the SCL clock tLOW 1.3 - 4.7 - s High period of the SCL clock tHIGH 0.6 - 4.0 - s Set up time Re-start condition tSU:STA 0.6 - 4.7 - s Data hold time tHD:DAT 0 0.9 0 - s Data set up time tSU:DAT 100 - 250 - ns Rise time of SDA and SCL tR 20+0.1Cb 300 - 1000 ns Fall time of SDA and SCL tF 20+0.1Cb 300 - 300 ns Set up time stop condition tSU:STO 0.6 - 4.0 - s Cb - 400 - 400 pF Hold time start condition Capacitive load for SDA line and SCL line Timing chart SDA tBUS tHD:STA tLOW tf tr SCL P S tHD:STA tHD:DAT tSU:DAT tSU:STA Sr Fig.1 SDA, SCL timing chart 7/15 tSU:STO P Function Start condition The start condition is a "HIGH" to "LOW" transition of the SDA line while SCL is "HIGH". Stop condition The stop condition is a "LOW" to "HIGH" transition of the SDA line while SCL is "HIGH". SDA SCL S P Start condition Stop condition Fig.2 Start / Stop condition Acknowledge The master (p) puts a resistive "HIGH" level on the SDA line during the acknowledge clock pulse. The peripheral (audio processor) that acknowledge has to pull-down ("LOW") the SDA line during the acknowledge clock pulse, so that the SDA line is stable "LOW" during this clock pulse. The slave which has been addressed has to generate an acknowledgement after the reception of each byte, otherwise the SDA line remains at the "HIGH" level during the ninth clock pulse time. In this case the master transmitter can generate the STOP information in order to abort the transfer. clock for acknowledge SCL (from master) 1 8 9 SDA (from master) not confirm SDA (from slave) S confirm Fig.3 Acknowledge 8/15 ACK signal Write DATA Send the stave address from master following the start condition (S). This address consists of 7 bits. The left 1 bit (the foot bit) is fixed "0". The stop condition (P) is needed to finish the data transferred. But the re-send starting condition (Sr) enables to transfer the data without STOP (P). S slave address R/W ACK DATA ACK P DATA ACK Sr "0" (Write) S slave address R/W ACK slave address R/W "0" (Write) ACK DATA ACK P "0" (Write) Fig.4 DATA transmit Data format The format is following. S A6 A5 A4 A3 A2 A1 A0 R/W ACK D7 D6 D5 SLAVE ADDRESS D4 D3 D2 D1 D0 ACK P WRITE DATA Table 1 for WRITE format A0A2 Each bit can be defined by the input levels of pins A0A3. A3A6 These 4 bits are fixed. Slave address R/W "0" Write "1" to D0 makes Q0 pin High-impedance. And write "0" makes Q0 Write Data D0D7 pin LOW. D[1:7] and Q[1:7] are same as D0 and Q0. Table 2 for (A2, A1, A0) to SLAVE ADDRESS A6 A5 A4 A3 A2 A1 A0 Slave address 0 1 1 1 0 0 0 38H 0 1 1 1 0 0 1 39H 0 1 1 1 0 1 0 3AH 0 1 1 1 0 1 1 3BH 0 1 1 1 1 0 0 3CH 0 1 1 1 1 0 1 3DH 0 1 1 1 1 1 0 3EH 0 1 1 1 1 1 1 3FH Fixed for BU2098F Defined by external pin A0A2 9/15 Data transmission timing SDA S A6 A5 A4 A3 A2 A1 A0 R/W ACK D7 D6 D5 Slave address D4 D3 D2 D1 D0 ACK P Write data Latch pulse Output (Q7Q0) Output the write data to Q7Q0 at the same time. Fig.5 Timing chart for WRITE Command sample for driving LEDs. These are all off. (terminal A0A2 is open) Power Supply ON LEDs all-ON with power supply ON SDA S 0 1 1 1 1 1 1 0 ACK 1 1 1 Slave address 1 1 1 1 1 ACK P Write data LEDs are all-off by this command. RESET CONDITION After reset, Q0Q7 pins are ON. (LEDs are all ON.) RISING TIME OF POWER SUPPLY VDD must rise within 10ms. If the rise time would exceed 10ms, it is afraid not to reset the BU2098F. VDD GND t10ms Fig.6 Rising time of power supply 10/15 BU2090F/FS AC characteristics (unless otherwise noted, VDD=5V, VSS=0V, Ta=25) Limit Parameter Symbol Minimum clock frequency Unit Condition Min. Typ. Max. 500 - - ns VDD=5V 1000 - - ns VDD=3V 200 - - ns VDD=5V 300 - - ns VDD=3V 200 - - ns VDD=5V 400 - - ns VDD=3V 50 - - ns VDD=5V 100 - - ns VDD=3V 250 - - ns VDD=5V 500 - - ns VDD=3V 200 - - ns VDD=5V 400 - - ns VDD=3V 250 - - ns VDD=5V 500 - - ns VDD=3V tw Data shift set up time tSU Data shift hold time tH Data latch set up time tLSUH Data latch hold time tLHH Data latch "L" tLSUL set up time Data latch "L" tLHL hold time Switching time test circuit 25V VDD RL 10k Q0 Pulse Gen. CLOCK 25V Pulse Gen. RL 10k DATA Q11 GND (Vss) Fig.7 Switching time test waveforms tW 90% tW VDD 90% 90% 10% 10% 10% 10% GND (Vss) CLOCK tSU tH tLSUL tLHL tLSUH tLHH VDD 90% 90% 90% 10% 10% 90% GND (Vss) DATA Fig.8 11/15 Timing chart BU2098F Slave address SCL Device code External terminal 1 5 2 3 4 6 7 8 9 1 2 3 4 5 6 7 8 9 Start condition Stop condition SDA VCC A6 A5 A4 A3 A2 A1 A0 RW ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Note) Diagram shows a status where a pull-up resistor is connected to output. 12/15 Timing chart BU2090F/FS CLOCK DATA D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Q11 Q10 Q9 Q8 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Note1) Indicates undefined output. Note2) Output terminal is provided with a pull-up resistor. 13/15 Operation Notes 1. Absolute maximum ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses. 2. Connecting the power supply connector backward Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply lines. An external direction diode can be added. 3. Power supply lines Design PCB layout pattern to provide low impedance GND and supply lines. To obtain a low noise ground and supply line, separate the ground section and supply lines of the digital and analog blocks. Furthermore, for all power supply terminals to ICs, connect a capacitor between the power supply and the GND terminal. When applying electrolytic capacitors in the circuit, not that capacitance characteristic values are reduced at low temperatures. 4. GND voltage The potential of GND pin must be minimum potential in all operating conditions. 5. Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 6. Inter-pin shorts and mounting errors Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any connection error or if pins are shorted together. 7. Actions in strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. 8. Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure. Use similar precaution when transporting or storing the IC. 9. Ground Wiring Pattern When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external components, either. 10. Unused input terminals Connect all unused input terminals to VDD or VSS in order to prevent excessive current or oscillation. Insertion of a resistor (100k approx.) is also recommended. 14/15 Type Designations (Selections) for Ordering B U 2 0 Product name 9 8 F Package type BU2098 BU2090 E 2 E1 Emboss tape reel Pin 1 on draw-out side E2 Emboss tape reel Pin 1 opposite draw-out side TL Emboss tape reel Pin 1 on draw-out side TR Emboss tape reel Pin 1 opposite draw-out side F : SOP16 FS : SSOP-A16 SOP16 <Tape and Reel information> <Dimension> Tape 1.50.1 9 1 8 4.40.2 0.3Min. 16 Quantity 2500pcs Direction of feed E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.150.1 0.1 1234 1234 1Pin 1234 1234 1234 1234 0.40.1 1234 1.27 1234 0.11 6.20.3 10.00.2 Embossed carrier tape Direction of feed Reel (Unit:mm) When you order , please order in times the amount of package quantity. SSOP-A16 <Dimension> <Tape and Reel information> Embossed carrier tape Tape 1 8 Direction of feed (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.150.1 1234 1234 1234 1Pin 1234 1234 0.360.1 1234 0.1 1234 0.8 2500pcs E2 1234 1.50.1 4.40.2 0.11 6.20.3 9 0.3Min. 6.60.2 16 Quantity Direction of feed Reel (Unit:mm) When you order , please order in times the amount of package quantity. 15/15 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright (c) 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0