Preliminary FM25LX64 64Kb Serial 1.5V F-RAM Memory FEATURES 64K bit Ferroelectric Nonvolatile RAM Organized as 8,192 x 8 bits High Endurance 1 Trillion (1012) Read/Writes 36 Year Data Retention at +75C NoDelayTM Writes Advanced High-Reliability Ferroelectric Process Fast SPI Interface Up to 20 MHz Frequency SPI Mode 0 & 3 (CPOL, CPHA=0,0 & 1,1) Software Write-Protection (BP bits) Hardware Write-Protect (/WP pin) DESCRIPTION The FM25LX64 is a 1.5V 64-kilobit nonvolatile memory employing an advanced ferroelectric process. A ferroelectric random access memory or FRAM is nonvolatile and performs reads and writes like a RAM. It provides reliable data retention for 36 years while eliminating the complexities, overhead, and system level reliability problems caused by EEPROM and other nonvolatile memories. The FM25LX64 performs write operations at bus speed. No write delays are incurred. Data is written to the memory array immediately after each byte has been successfully transferred to the device. The next bus cycle may commence immediately without the need for data polling. In addition, the product offers substantial write endurance compared with other nonvolatile memories. The FM25LX64 is capable of supporting 1012 read/write cycles, or 1 million times more write cycles than EEPROM. These capabilities make the FM25LX64 ideal for nonvolatile memory applications requiring frequent or rapid writes. Examples range from data collection, where the number of write cycles may be critical, to demanding industrial controls where the long write time of EEPROM can cause data loss. The FM25LX64 provides substantial benefits to users of serial EEPROM as a hardware drop-in replacement. The FM25LX64 uses the high-speed SPI bus, which enhances the high-speed write This is a product that has fixed target specifications but are subject to change pending characterization results. Rev. 1.1 Feb. 2012 Active-Low RESET Input Holds Device in Reset State While Power Stabilizes Reduces Time to First F-RAM Access Allows Freedom of Power Supply Ramp Rates Low Voltage/ Low Energy Consumption Low Voltage Operation 1.5V +0.15V, -0.1V 20 A (typ.) Active Current at 1 MHz 0.1 A (typ.) Standby Current Industry Standard Configuration Industrial Temperature -40C to +85C 8-pin "Green"/RoHS SOIC Package capability of F-RAM technology. Device specifications are guaranteed over an industrial temperature range of -40C to +85C. PIN CONFIGURATION CS SO WP 1 8 2 7 3 6 VDD RST SCK VSS 4 5 SI Pin Name /CS SCK SI SO /RST /WP VDD VSS Function Chip Select Serial Clock Serial Data Input Serial Data Output Reset Input Write Protect Input Supply Voltage Ground Ordering Information FM25LX64-G "Green" 8-pin SOIC FM25LX64-GTR "Green" 8-pin SOIC, Tape & Reel Ramtron International Corporation 1850 Ramtron Drive, Colorado Springs, CO 80921 (800) 545-FRAM, (719) 481-7000 http://www.ramtron.com Page 1 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM RST Instruction Decode Clock Generator Control Logic Write Protect CS SCK 1,024 x 64 FRAM Array Instruction Register Address Register Counter SI 13 8 Data I/O Register SO 3 Nonvolatile Status Register Figure 1. Block Diagram PIN DESCRIPTIONS Pin Name /RST I/O Input /CS Input SCK Input SI Input SO Output /WP Input VDD VSS Supply Supply Rev. 1.1 Feb. 2012 Description Reset Input: This active-low pin is used to hold the memory in a reset state while power is being stabilized. When /RST is low, the interface is inactive and the SPI state machine is reset. Once Vdd is within spec, the /RST pin may be driven high. The memory is ready for commands within tPU. Chip Select: This active low input activates the device. When high, the device enters low-power standby mode and ignores other inputs. When low, the device internally activates the SCK signal. A falling edge on /CS must occur prior to every op-code. Serial Clock: All I/O activity is synchronized to the serial clock. Inputs are latched on the rising edge and outputs occur on the rising edge. Since the device is static, the clock frequency may be any value between 0 and 20 MHz and may be interrupted at any time. Serial Input: All data is input to the device on this pin. The pin is sampled on the rising edge of SCK and is ignored at other times. It should always be driven to a valid logic level to meet IDD specifications. Serial Output: This is the data output pin. It behaves differently from a standard SPI SO pin. Data is driven during a read from the rising edge of SCK instead of the falling edge. SO is driven at all times. Write Protect: This active low pin prevents write operations to the status register only. A complete explanation of write protection is provided on pages 7 and 8. Power Supply (1.4V to 1.65V) Ground Page 2 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM OVERVIEW The FM25LX64 is a 1.5V serial F-RAM memory. The memory array is logically organized as 8,192 x 8 and is accessed using an industry standard Serial Peripheral Interface or SPI bus. Functional operation of the F-RAM is similar to serial EEPROMs. The major difference between the FM25LX64 and a serial EEPROM with the same pinout is the F-RAM's superior write performance. MEMORY ARCHITECTURE When accessing the FM25LX64, the user addresses 8,192 locations of 8 data bits each. These data bits are shifted serially. The addresses are accessed using the SPI protocol, which includes a chip select, an op-code, and a two-byte address. The upper 3 bits of the address range are `don't care' values. The complete address of 13-bits specifies each byte address uniquely. Most functions of the FM25LX64 either are controlled by the SPI interface or are handled automatically by onboard circuitry. The access time for memory operation is essentially zero, beyond the time needed for the serial protocol. That is, the memory is read or written at the speed of the SPI bus. Unlike an EEPROM, it is not necessary to poll the device for a ready condition since writes occur at bus speed. So, by the time a new bus transaction can be shifted into the device, a write operation will be complete. This is explained in more detail in the interface section. Users expect several obvious system benefits from the FM25LX64 due to its fast write cycle and high endurance as compared to EEPROM. In applications that have a limited power budget, the fast-write and low-power operation provides a much lower energy solution for nonvolatile store compared to EEPROM since the access is completed quicker and at a very low voltage. By contrast, an EEPROM requires milliseconds to perform a write operation and at much higher currents. RESET A reset input (/RST) is provided as a means to hold the memory interface in a reset state during power cycle events. When /RST is driven low, the memory enters a reset condition. In this state, the interface is locked out and the SO pin is high impedance. When /RST is driven high, the memory enters a normal operating mode after the tPU time is satisfied. Driving /RST low during a read or write operation will abort the operation and data may be lost. Note: The FM25LX64 contains no power management circuits. To ensure proper operation, the user is responsible for /RST being held active (low) while VDD voltage stabilizes and is within the specified DC min/max limits. It is recommended that the part is not powered down with chip enable active. SERIAL PERIPHERAL INTERFACE - SPI BUS The FM25LX64 employs a Serial Peripheral Interface (SPI) bus. It is specified to operate at speeds up to 20 MHz. This high-speed serial bus provides high performance serial communication to a host microcontroller. Many common microcontrollers have hardware SPI ports allowing a direct interface. It is quite simple to emulate the port using ordinary port pins for microcontrollers that do not. The FM25LX64 operates in SPI Mode 0 and 3. The SPI interface uses a total of four pins: clock, data-in, data-out, and chip select. A typical system configuration uses a single FM25LX64 device with a microcontroller that has a dedicated SPI port, as Figure 2 illustrates. Note that there may be additional delay required in the SO path to account for proper data output hold timing. A one-gate buffer `1G125 is shown. For a microcontroller that has no dedicated SPI bus, a general purpose port may be used. Figure 3 shows a configuration that uses the MCU GPIO pins. Rev. 1.1 Feb. 2012 Page 3 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM SCK MOSI MISO `1G125 SPI Microcontroller SO SI SCK FM25LX64 CS RST SS MOSI : Master Out Slave In MISO : Master In Slave Out SS : Slave Select System Reset Figure 2. System Configuration with SPI port P1.0 P1.1 P1.2 Microcontroller SO SI SCK FM25LX64 P1.3 CS RST System Reset Figure 3. System Configuration without SPI port OPERATING VOLTAGE It should be noted that the operating voltage range allow the use of 1.5V and 1.6V voltage regulators that are spec'd to an output voltage of 3%. A 1.5V regulator with a 3% has a VOUT min of 1.455V and a max of 1.545V. A 1.6V regulator with a 3% has a VOUT min of 1.552V and a max of 1.648V. The FM25LX64 is spec'd to operate from VDD = 1.40V to 1.65V which meets both voltage rail tolerances. Protocol Overview The SPI interface is a synchronous serial interface using clock and data pins. Once chip select is activated by the bus master, the FM25LX64 will begin monitoring the clock and data lines. The relationship between the falling edge of /CS, the clock and data is dictated by the SPI mode. The device will make a determination of the SPI mode on the falling edge of each chip select. While there are four such modes, the FM25LX64 supports Modes 0 and 3. Figure 4 shows the required signal relationships for Modes 0 and 3. For both modes, data is clocked into the FM25LX64 on the rising edge of SCK and data is expected on the first rising edge after /CS goes active. If the clock begins from a high state, it will fall prior to beginning data transfer in order to create the first rising edge. The SPI protocol is controlled by op-codes. These op-codes specify the commands to the device. After /CS is activated the first byte transferred from the bus master is the op-code. Following the op-code, any addresses and data are then transferred. Note that the WREN and WRDI op-codes are commands with no subsequent data transfer. Rev. 1.1 Feb. 2012 Page 4 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM Important: The /CS pin must go inactive after an operation is complete and before a new op-code can be issued. There is one valid op-code only per active chip select. SPI Mode 0: CPOL=0, CPHA=0 7 6 5 4 3 2 1 0 SPI Mode 3: CPOL=1, CPHA=1 7 6 5 4 3 2 1 0 Figure 4. SPI Modes 0 & 3 Power Up to First Access The FM25LX64 is not accessible for a period of time (tPU) after power up. Users must comply with the timing parameter tPU, which is the minimum time from /RST deasserted to the first /CS low. Data Transfer All data transfers to and from the FM25LX64 occur in 8-bit groups. They are synchronized to the clock signal (SCK), and they transfer most significant bit (MSB) first. Serial inputs are registered on the rising edge of SCK. Outputs are driven from the rising edge of SCK. This is different compared to a standard SPI device. Command Structure There are six commands called op-codes that can be issued by the bus master to the FM25LX64. They are listed in the table below. These op-codes control the functions performed by the memory. They can be divided into three categories. First, there are commands that have no subsequent operations. They perform a single function such as to enable a write operation. Second are commands followed by one byte, either in or out. They operate on the Status Register. The third group includes commands for memory transactions followed by address and one or more bytes of data. Table 1. Op-code Commands Name Description Set Write Enable Latch WREN Write Disable WRDI Read Status Register RDSR Write Status Register WRSR Read Memory Data READ WRITE Write Memory Data Rev. 1.1 Feb. 2012 Op-code Hex 0000 0000 0000 0000 0000 0000 0x06 0x04 0x05 0x01 0x03 0x02 0110b 0100b 0101b 0001b 0011b 0010b Page 5 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM WREN - Set Write Enable Latch The FM25LX64 will power up with writes disabled. The WREN command must be issued prior to any write operation. Sending the WREN op-code will allow the user to issue subsequent op-codes for write operations. These include writing the Status Register (WRSR) and writing the memory (WRITE). Sending the WREN op-code causes the internal Write Enable Latch to be set. A flag bit in the Status Register, called WEL, indicates the state of the latch. WEL=1 indicates that writes are permitted. Attempting to write the WEL bit in the Status Register has no effect on the state of this bit - only the WREN op-code can set this bit. The WEL bit will be automatically cleared on the rising edge of /CS following a WRDI, a WRSR, or a WRITE operation. This prevents further writes to the Status Register or the F-RAM array without another WREN command. Figure 5 below illustrates the WREN command bus configuration. WRDI - Write Disable The WRDI command disables all write activity by clearing the Write Enable Latch. The user can verify that writes are disabled by reading the WEL bit in the Status Register and verifying that WEL=0. Figure 6 illustrates the WRDI command bus configuration. CS 0 1 2 3 4 5 6 7 0 1 1 0 SCK SI 0 0 0 0 SO Figure 5. WREN Bus Timing CS 0 1 2 3 4 5 6 7 0 1 0 0 SCK SI 0 0 0 0 SO Figure 6. WRDI Bus Timing RDSR - Read Status Register The RDSR command allows the bus master to verify the contents of the Status Register. Reading Status provides information about the current state of the write protection features. Following the RDSR op-code, the FM25LX64 will return one byte with the contents of the Status Register. The Status Register is described in detail in a later section. WRSR - Write Status Register The WRSR command allows the user to select certain write protection features by writing a byte to the Status Register. Prior to issuing a WRSR command, the /WP pin must be high or inactive. Note that on the FM25LX64, /WP only prevents writing to the Status Register, not the memory array. Prior to sending the Rev. 1.1 Feb. 2012 Page 6 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM WRSR command, the user must send a WREN command to enable writes. Note that executing a WRSR command is a write operation and therefore clears the Write Enable Latch. CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK SI 0 0 0 0 0 1 0 1 7 SO 6 5 4 3 2 1 0 Figure 7. RDSR Bus Timing CS SCK SI SO Figure 8. WRSR Bus Timing (WREN not shown) STATUS REGISTER & WRITE PROTECTION The write protection features of the FM25LX64 are multi-tiered. A WREN op-code must be issued prior to any write operation. Assuming that writes are enabled using WREN, writes to memory are controlled by the Status Register. As described above, writes to the Status Register are performed using the WRSR command and subject to the /WP pin. The Status Register is organized as follows. Table 2. Status Register Bit Name 7 WPEN 6 0 5 0 4 0 3 BP1 2 BP0 1 WEL 0 0 Bits 0 and 4-6 are fixed at 0 and cannot be modified. Note that bit 0 ("Ready" in EEPROMs) is unnecessary as the F-RAM writes in real-time and is never busy. The WPEN, BP1 and BP0 control write protection features. They are nonvolatile (shaded yellow). The WEL flag indicates the state of the Write Enable Latch. Attempting to directly write the WEL bit in the Status Register has no effect on its state. This bit is internally set and cleared via the WREN and WRDI commands, respectively. BP1 and BP0 are memory block write protection bits. They specify portions of memory that are write-protected as shown in the following table. Table 3. Block Memory Write Protection BP1 BP0 Protected Address Range 0 0 None 0 1 1800h to 1FFFh (upper 1/4) 1 0 1000h to 1FFFh (upper 1/2) 1 1 0000h to 1FFFh (all) The BP1 and BP0 bits and the Write Enable Latch are the only mechanisms that protect the memory from writes. The remaining write protection features protect inadvertent changes to the block protect bits. Rev. 1.1 Feb. 2012 Page 7 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM The WPEN bit controls the effect of the hardware /WP pin. When WPEN is low, the /WP pin is ignored. When WPEN is high, the /WP pin controls write access to the Status Register. Thus the Status Register is write protected if WPEN=1 and /WP=0. This scheme provides a write protection mechanism, which can prevent software from writing the memory under any circumstances. This occurs if the BP1 and BP0 are set to 1, the WPEN bit is set to 1, and /WP is set to 0. This occurs because the block protect bits prevent writing memory and the /WP signal in hardware prevents altering the block protect bits (if WPEN is high). Therefore in this condition, hardware must be involved in allowing a write operation. The following table summarizes the write protection conditions. Table 4. Write Protection WEL WPEN /WP 0 X X 1 0 X 1 1 0 1 1 1 Protected Blocks Protected Protected Protected Protected Unprotected Blocks Protected Unprotected Unprotected Unprotected Status Register Protected Unprotected Protected Unprotected MEMORY OPERATION The SPI interface, which is capable of a relatively high clock frequency, highlights the fast write capability of the F-RAM technology. Unlike SPI-bus EEPROMs, the FM25LX64 can perform sequential writes at bus speed. No page register is needed and any number of sequential writes may be performed. Write Operation All writes to the memory begin with a WREN op-code with /CS being asserted and deasserted. The next op-code is WRITE. The WRITE op-code is followed by a two-byte address value. The upper 3-bits of the address are ignored. In total, the 13-bits specify the address of the first data byte of the write operation. This is the starting address of the first data byte of the write operation. Subsequent bytes are data bytes, which are written sequentially. Addresses are incremented internally as long as the bus master continues to issue clocks and keeps /CS low. If the last address of 1FFFh is reached, the counter will roll over to 0000h. Data is written MSB first. The rising edge of /CS terminates a WRITE operation. A write operation is shown in Figure 9. EEPROMs use page buffers to increase their write throughput. This compensates for the technology's inherently slow write operations. F-RAM memories do not have page buffers because each byte is written to the F-RAM array immediately after it is clocked in (after the 8th clock). This allows any number of bytes to be written without page buffer delays. CS 0 1 2 3 4 5 6 7 0 1 2 X X X 3 4 5 6 7 4 5 6 7 0 1 2 3 4 5 6 7 9 8 3 2 1 0 7 6 Data 5 4 3 2 1 0 SCK op-code SI 0 0 0 0 0 13-bit Add ress 0 1 0 12 11 10 MSB LSB MSB LSB SO Figure 9. Memory Write (WREN not shown) Read Operation After the falling edge of /CS, the bus master can issue a READ op-code. Following the READ command is a twobyte address value. The upper 3-bits of the address are ignored. In total, the 13-bits specify the address of the first byte of the read operation. This is the starting address of the first byte of the read operation. After the op-code and address are issued, the device drives out the read data on the next 8 clocks. The SI input is ignored during read data bytes. Subsequent bytes are data bytes, which are read out sequentially. Addresses are incremented internally Rev. 1.1 Feb. 2012 Page 8 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM as long as the bus master continues to issue clocks and /CS is low. If the last address of 1FFFh is reached, the counter will roll over to 0000h. Data is read MSB first. The rising edge of /CS terminates a READ operation. A read operation is shown in Figure 10. CS 0 1 2 3 4 5 6 7 0 1 X X 2 3 4 5 6 7 4 9 8 3 5 6 7 1 0 0 1 2 3 4 5 6 7 SCK 14-bit Address op-code SI 0 0 0 0 0 0 1 1 13 12 11 10 MSB 2 LSB SO Data MSB 7 6 5 4 3 LSB 2 1 0 Figure 10. Memory Read ENDURANCE The FM25LX64 devices are capable of being accessed at least 10 14 times, reads or writes. An F-RAM memory operates with a read and restore mechanism. Therefore, an endurance cycle is applied on a row basis for each access (read or write) to the memory array. The F-RAM architecture is based on an array of rows and columns. Rows are defined by A12-A3 and column addresses by A2-A0. See Block Diagram (pg 2) which shows the array as 1K rows of 64-bits each. The entire row is internally accessed once whether a single byte or all eight bytes are read or written. Each byte in the row is counted only once in an endurance calculation. The table below shows endurance calculations for 64-byte repeating loop, which includes an op-code, a starting address, and a sequential 64-byte data stream. This causes each byte to experience one endurance cycle through the loop. F-RAM read and write endurance is virtually unlimited even at 20MHz clock rate. Table 5. Time to Reach Endurance Limit for Repeating 64-byte Loop SCK Freq Endurance Endurance Years to Reach (MHz) Cycles/sec. Cycles/year Limit 20 37,310 1.18 x 1012 85.1 10 18,660 5.88 x 1011 170.2 5 9,330 2.94 x 1011 340.3 Rev. 1.1 Feb. 2012 Page 9 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Symbol Description VDD Power Supply Voltage with respect to VSS VIN Voltage on any pin with respect to VSS TSTG TLEAD VESD Storage Temperature Lead Temperature (Soldering, 10 seconds) Electrostatic Discharge Voltage - Human Body Model (AEC-Q100-002 Rev. E) - Charged Device Model (AEC-Q100-011 Rev. B) - Machine Model (AEC-Q100-003 Rev. E) Package Moisture Sensitivity Level Ratings -1.0V to +2.4V -1.0V to +2.4V and VIN < VDD+0.7V -55C to + 125C 260 C TBD TBD TBD MSL-1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only, and the functional operation of the device at these or any other conditions above those listed in the operational section of this specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. DC Operating Conditions (TA = -40 C to + 85 C, VDD = 1.4V to 1.65V unless otherwise specified) Symbol Parameter Min Typ Max Units VDD Power Supply Voltage 1.40 1.5 1.65 V IDD VDD Supply Current @ SCK = 1.0 MHz 20 60 A @ SCK = 20.0 MHz 400 900 A ISB Standby Current /RST High 0.1 3 A /RST Low 20 50 A ILI Input Leakage Current 1 A ILO Output Leakage Current 1 A VIH Input High Voltage 0.75 VDD VDD + 0.3 V VIL Input Low Voltage -0.3 0.25 VDD V VOH Output High Voltage VDD - 0.3 V @ IOH = -1 mA VOL Output Low Voltage 0.2 V @ IOL = 1 mA Notes 1. SCK toggling between VDD-0.2V and VSS, other inputs VSS or VDD-0.2V. SO=open. 2. SCK = SI = /CS=VDD. All inputs VSS or VDD. 3. VSS VIN VDD and VSS VOUT VDD. Rev. 1.1 Feb. 2012 Notes 1 2 3 3 Page 10 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM AC Parameters (TA = -40 C to + 85 C, CL = 30pF, VDD = 1.4V to 1.65V unless otherwise specified) Symbol Parameter Min Max Units Notes fCK SCK Clock Frequency 0 20 MHz tCH Clock High Time 22 ns 1 tCL Clock Low Time 22 ns 1 tCSU Chip Select Setup 10 ns tCSH Chip Select Hold 10 ns tOD Output Disable Time 20 ns 2 tODV Output Data Valid Time 20 ns tOH Output Hold Time 0 ns tD Deselect Time 60 ns tR Data In Rise Time 50 ns 2,3 tF Data In Fall Time 50 ns 2,3 tSU Data Setup Time 5 ns tH Data Hold Time 5 ns Notes 1. 2. 3. tCH + tCL = 1/fCK. Characterized but not 100% tested in production. Rise and fall times measured between 10% and 90% of waveform. Capacitance (TA = 25 C, f=1.0 MHz, VDD = 1.5V) Symbol Parameter CO Output Capacitance (SO) CI Input Capacitance Notes 1. Min - Max 8 6 Units pF pF Notes 1 1 This parameter is periodically sampled and not 100% tested. AC Test Conditions Input Pulse Levels Input rise and fall times Input and output timing levels Output Load Capacitance Data Retention Symbol Parameter TDR @ +85C @ +80C @ +75C Rev. 1.1 Feb. 2012 10% and 90% of VDD 5 ns 0.5 VDD 30 pF Min 10 18 36 Max - Units Years Years Years Notes Page 11 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM Serial Data Bus Timing tD CS tCSU tF 1/tCK tCL tR tCH tCSH SCK tSU tH SI tOH tODV tOD SO Power Cycle Timing VDD VDD min tVF tVR tRS tRH RST tPU tPD CS Power Cycle Timing (TA = -40 C to + 85 C, VDD = 1.4V to 1.65V unless otherwise specified) Symbol Parameter Min Max Units tPU /RST High to First Access Start 15 s tPD Last Access Complete to VDD(min) 0.2 s tVR VDD Rise Time 1 s/V tVF VDD Fall Time 1 s/V tRH /RST Hold Time after VDD(min) at Power Up 0 s tRS /RST Setup Time to VDD(min) at Power Down 0 s Notes 1. Slope measured at any point on VDD waveform. Rev. 1.1 Feb. 2012 Notes 1 1 Page 12 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM MECHANICAL DRAWING 8-pin SOIC (JEDEC MS-012 variation AA) Recommended PCB Footprint 7.70 3.90 0.10 3.70 6.00 0.20 2.00 Pin 1 0.65 1.27 4.90 0.10 1.27 0.33 0.51 0.25 0.50 1.35 1.75 0.10 0.25 0.10 mm 0- 8 0.19 0.25 45 0.40 1.27 Refer to JEDEC MS-012 for complete dimensions and notes. All dimensions in millimeters. SOIC Package Marking Scheme XXXXXXXP RLLLLLLL RICYYWW Legend: XXXXXXX= part number, P= package type (G=SOIC) R=rev code, LLLLLLL= lot code RIC=Ramtron Int'l Corp, YY=year, WW=work week Example: FM25LX64, "Green" SOIC package, Year 2011, Work Week 47 FM25LX64G ESA00002G1 RIC1147 Rev. 1.1 Feb. 2012 Page 13 of 14 FM25LX64 - 64Kb 1.5V SPI F-RAM REVISION HISTORY Revision 1.0 1.1 Rev. 1.1 Feb. 2012 Date 11/8/2011 12/5/2011 Summary Initial Release Updated DC specs and timing diagrams (SO never tri-states) Page 14 of 14