Effective May 2017 Supersedes August 2010 Technical Data 4378 42510ESDA-TR1 HALOGEN HF FREE ESD suppressor four-channel Pb Design considerations Surface Mount Device Product features * Halogen free, lead free and RoHS compliant for global applications * Ultra-low capacitance (0.1pF typical) ideally suited for protecting high speed data applications * Provides ESD protection with fast response time (<1ns) allowing equipment to pass the IEC 61000-4-2 Level 4 test * Four (4) channel array * Zero signal distortion * Low leakage current (<0.01A typical) Applications * * * * * * * Digital video equipment Mobile phone GPS Antenna Bluetooth communication equipment antenna circuit IEEE-1394 DVI HDMI Characteristic Rated Voltage (max) Leakage Current (max @ 12Vdc) Trigger Voltage (Vt) Clamping Voltage (Vc) Capacitance (Cp) @1MHz* Response Time Value/Range 12 V 0.01 A 300 V Typical 30 V Typical 0.1 pF Typical <1 ns ESD Voltage Capability, IEC 61000-4-2 8 kV Contact Discharge Mode ESD Voltage Capability, IEC 61000-4-2 15 kV Air Discharge Mode ESD Withstand Pulses 100 Times Minimal * Note, Capacitance measured with 1 Vrms * Follow the soldering recommendations to avoid deforming product * Do not use high temperature, high humidity or corrosive atmospheres (sulfide and chloride gas) that could damage the solderability * Moisture Sensitivity Level (MSL) according to J-STD-020 standard: Level 2 (Floor Life 1 year under <30C/65%RH conditions) Solderability requirement according to IPC/JEDEC JSTD-002C, Test D, Test B1 * Use Sn/Ag/Cu (96.5/3.0/0.5) or equivalent solder and activated flux #5 or equivalent. Part Numbering System: 4 2510 ESDA- TR1 * Four channel SIN 1 chip * 2.5x1.0mm footprint size * ESDA ESD Suppressor * Tape and reel packaging code Ordering Part Number Description 42510ESDA-TR1 5000 suppressors in paper tape on a 7 inch (178 mm) reel Environmental Specifications Characteristic Load Humidity Thermal Shock Value +85 C/90% RH with rated voltage for 1000 hrs -40 C to +85 C, 30 minute cycle, 5 cycles J-STD-020 Standard: Level 2 Moisture Resistance Test (1 year floor life under 30 C/65% RH conditions Operating Temperature Range -40 C to +85 C (-40 F to 185 F) Storage Temperature Range -55 C to +125 C (-67 F to +257 F) 42510ESDA-TR1 ESD suppressor four-channel Technical Data 4378 Effective May 2017 Dimensions - mm Recommended Pad Layout - mm W B L T D E C B C D E L T W 0.2 0.1 0.3 0.05 0.2 0.05 0.5 0.05 2.5 0.1 0.5 0.1 1.0 0.1 G P P1 X X1 0.2 0.5 1 0.2 0.3 Note: Print solder 0.01~0.015mm thick. Y Y1 Z 0.6 1.4 1.4 Packaging-mm Soldering recommendations Supplied in tape and reel packaging, 5000 parts per seven inch (178 mm) reel per EIA Standard 481-1 * Compatible with lead and lead-free solder reflow processes * Hand soldering - soldering tip should not directly touch part +280 C max for 3 sec. max * Peak reflow temperatures and durations: o IR Reflow = 260C max for 20 sec. max o Wave Solder = 260C max for 10 sec. max ( & ) ' / $ % : Recommended IR Reflow Profile 7RS7DSH Unit: mm A B C D E F L W 8.00 3.50 1.75 2.00 4.00 1.50 2.90 1.40 0.30 0.05 0.10 0.05 0.10 0.10 0.20 0.20 Circuit Schematic HDMI Application Life Support Policy: Eaton does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Eaton reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Eaton also reserves the right to change or update, without notice, any technical information contained in this bulletin. Eaton Electronics Division 1000 Eaton Boulevard Cleveland, OH 44122 United States www.eaton.com/electronics (c) 2017 Eaton All Rights Reserved Printed in USA Publication No. 4378 BU-SB10816 May 2017 Eaton is a registered trademark. All other trademarks are property of their respective owners.