300-6300-CNA-0002B - 3M - Datasheet.Live

3M Electronic Handling and Protection Division

6801 River Place Blvd.

Austin, TX 78726-9000

Test

& Burn-In PGA Kit Sockets

Pin Grid Arrays

Date Issued: June 20, 2001

TS-0675-09

Sheet

1 of 2

Physical

Insulation

Material: Polyethersyfone (PES)

Flammability:

UL 94V

-0

Color: Black

Marking:

3M Logo & Part Number Identifier

Cam Handle

Material:

Stainless Steel

Contact

Material:

Beryllium Copper

Plating Options:

Electrical

Curr

ent Rating:

1 Amp

Insulation Resistance:

> 1

at 500 Vdc

ithstanding V

oltage:

1000 V

rms at Sea Level

Environmental

Temperatur

e Rating Operating:

- 55°

∞

C to + 150°

∞C

Mechanical

When used as a test socket at room temperature 24°

∞

C the socket will last

25,000 actuations.

Based on field experience, under normal burn-in conditions up to a

maximum of 150°

∞

C, the socket should last an average of four years.

• Available in 10 x 10 matrix through 25 x 25 

 matrix

• Used when only a few test sockets are needed

• Provides individual components ready for 

 assembly 

• Open pattern top plate; load only those contacts 

 needed for your specific device pin pattern

For

technical, sales or ordering information call

800-328-0411

or visit our website: http://www.3M.com/ehpd

30 m" (0.76 mm) Gold over 50 m" (1.3 mm) Nickel

Electronic Handling and Protection Division

6801 River Place Blvd.

Austin, TX 78726-9000

Test

& Burn-In PGA Kit Socket

Pin Grid Arrays

Part

Number

Matrix Size Description

200-6310-9UN-1900 10 x 10

200-6311-9UN-1900 11 x 11

200-6313-9UN-1900 13 x 13

200-6315-9UN-1900 15 x 15

S k t Kit W/O C t t

200-6317-9UN-1900 17 x 17 Socket Kit W/O Contacts

200-6319-9UN-1900 19 x 19

200-6321-9UN-1900 21 x 21

200-6325-9UN-1900 25 x 25

300-6300-CNA-0002B Each Contact–BeCu/Au Plated

200-4660-14-1900 Set of 10 Extra Hole Plugs

TS-0675-09

Sheet

2 of 2

Ordering Information

Phillips Pan-Hd

#0-80 x 5/16 Long

Assy Screw

10X Hole Plugs

op Plate

Contact

( Order Separately )

Cam Plate

Base Plate

Cam Handle

Standard

Handle

Assembly Instructions

1. Load

hole plugs into top plate by

pressing fitting into place.

Remove

from tie bar by cutting

with commercially available 6 1/2

flush diagonal cutter pliers.

Place cam plate into recessed

area of base plate, load

contacts in desired locations,

being careful that the bent leaf

of the contact is loaded in

correct position ( away from

cam handle. )

Insert cam handle into position

in the base plate.

Now make a final check that all

contacts are in desired location

and that all are fairly even at the

top. Also check cam to make

sure it is still in position. Now

take the top plate and place into

position and start to lower over

contacts. Start at the rear of the

socket and rotate downward

toward the front and then snap

locating bosses into place.

Several very slight back and

forth motions may be necessary

in order to get contacts to snap

into place. Care should be taken

that too much downward

pressure isn't applied which

could bend or damage the

contacts. Insert screws and

tighten.

Now make an operation check

by rotating handle 90

∞

. Make a

visual check of movement and

closure of all contacts. Rotate

handle and check the freedom

of movement of cam plate and

that the moving leaf of the

contact clears the entry hole. A

continuity check can be made

before final soldering by placing

device in socket, then closing

and making check. Soldering

should be done with socket in

the open position.

Notes:

1 Contact

and extra Hole Plugs are ordered separately

See T

est & Burn-In PGA socket section on page 29 for dimensional information on assembled sockets.

For

technical, sales or ordering information call

800-328-0411

or visit our website: http://www.3M.com/ehpd