150038561 - ABB - Datasheet.Live

GE

Data Sheet

November 4, 2016

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

Features

 Compliant to RoHS II EU “Directive 2011/65/EU”

 Compliant to REACH Directive (EC) No 1907/2006

 Compliant to IPC-9592 (September 2008), Category 2,

Class II

 Ultra low height design for very dense power

applications.

 Small size: 12.2 mm x 12.2 mm x 2.9 mm (Max)

(0.48 in x 0.48 in x 0.116 in)

 Output voltage programmable from 0.6Vdc to 5.5Vdc

via external resistor.

 Wide Input voltage range (3Vdc-14.4Vdc)

 Wide operating temperature range [-40°C to 85°C]. See

derating curves

 DOSA approved footprint

 Tunable LoopTM to optimize dynamic output voltage

response

 Flexible output voltage sequencing EZ-SEQUENCE

 Power Good signal

 Remote On/Off

 Fixed switching frequency with capability of external

synchronization

 Output overcurrent protection (non-latching)

 Overtemperature protection

 Ability to sink and source current

 Compatible in a Pb-free or SnPb reflow environment

 UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03

Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed

 ISO** 9001 and ISO 14001 certified manufacturing

facilities

Applications

 Distributed power architectures

 Intermediate bus voltage applications

 Telecommunications equipment

 Servers and storage applications

 Networking equipment

 Industrial equipment

Description

The 12A Analog Pico SlimLynxTM Open Frame power modules are non-isolated dc-dc converters that can deliver up to 12A of

output current. These modules operate over a wide range of input voltage (VIN = 3Vdc-14.4Vdc) and provide a precisely regulated

output voltage from 0.6Vdc to 5.5Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output

voltage, over current and over temperature protection. The module also includes the Tunable LoopTM feature that allows the user

to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to

savings on cost and PWB area.

* UL is a registered trademark of Underwriters Laboratories, Inc.

† CSA is a registered trademark of Canadian Standards Association.

‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.

** ISO is a registered trademark of the International Organization of Standards

TRIM

VOUT

VS+

GND

RTUNE

CTUNE

RTrim

VIN

Co

Cin

Vout+

Vin+

ON/OFF

SEQ

MODULE

PGOOD

SIG_GND

VS-

GND

SYNC

RoHS Compliant

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 2

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings

only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations

sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.

Parameter

Device

Symbol

Min

Max

Unit

Input Voltage

All

VIN

-0.3

15

V

Continuous

SEQ, SYNC, VS+

All

7

V

Operating Ambient Temperature

All

TA

-40

85

°C

(see Thermal Considerations section)

Storage Temperature

All

Tstg

-55

125

°C

Electrical Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.

Parameter

Device

Symbol

Min

Typ

Max

Unit

Operating Input Voltage

All

VIN

3



14.4

Vdc

Maximum Input Current

All

IIN,max

11

Adc

(VIN=3V to 14.4V, IO=IO, max )

Input No Load Current

(VIN = 12Vdc, IO = 0, module enabled)

VO,set = 0.6 Vdc

IIN,No load

50

mA

VO,set = 5.5Vdc

IIN,No load

180

mA

Input Stand-by Current

(VIN = 12Vdc, module disabled)

All

IIN,stand-by

8

mA

Inrush Transient

All

I2t

1

A2s

Input Reflected Ripple Current, peak-to-peak

(5Hz to 20MHz, 1μH source impedance; VIN =0 to 14V, IO=

IOmax ; See Test Configurations)

All

30

mAp-p

Input Ripple Rejection (120Hz)

All

-55

-

dB

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 3

Electrical Specifications (continued)

Parameter

Device

Symbol

Min

Typ

Max

Unit

Output Voltage Set-point (with 0.1% tolerance for external resistor

used to set output voltage)

All

VO, set

-1.0

+1.0

% VO, set

Output Voltage (Over all operating input voltage, resistive load,

and temperature conditions until end of life)

All

VO, set

-3.0



+3.0

% VO, set

Adjustment Range (selected by an external resistor)

(Some output voltages may not be possible depending on the

input voltage – see Feature Descriptions Section)

All

VO

0.6

5.5

Vdc

Remote Sense Range

All

0.5

Vdc

Output Regulation (for VO ≥ 2.5Vdc)

Line (VIN=VIN, min to VIN, max)

All



+0.4

% VO, set

Load (IO=IO, min to IO, max)

All



10

mV

Output Regulation (for VO < 2.5Vdc)

Line (VIN=VIN, min to VIN, max)

All



5

mV

Load (IO=IO, min to IO, max)

All



10

mV

Temperature (Tref=TA, min to TA, max)

All



0.4

% VO, set

Input Noise on nominal input at 25°C

(VIN=VIN, nom and IO=IO, min to IO, max Cin = 1x47nF(0402) or

equivalent , 2x22uF(1210) ceramic capacitors or equaivalent and

470uF,16V electrolytic)

Peak-to-Peak (Full Bandwidth) for all Vo

All



360

mVpk-pk

Output Ripple and Noise on nominal output at 25°C

(VIN=VIN, nom and IO=IO, min to IO, max Co = 2x47nF(0402) or equivalent,

2x47uF (1210) or equivalent ceramic capacitors on output and

1x47nF(0402) or equivalent, 2x22uF(1210) ceramic capacitors or

equivalent and 470uF,16V electrolytic) on input

Peak-to-Peak (Full bandwidth) Vo≤1.2Vo

30

mVpk-pk

Peak-to-Peak (Full bandwidth) Vo>1.2Vo

All

3%Vo

mVpk-pk

RMS (Full bandwidth) for all Vo

All

2%Vo

mVrms

External Capacitance1

Without the Tunable LoopTM

ESR ≥ 1 mΩ

All

CO, max

1x47uf

200uF

μF

With the Tunable LoopTM

ESR ≥ 0.15 mΩ

All

CO, max

200

1000

μF

ESR ≥ 10 mΩ

All

CO, max

5000

μF

Output Current (in either sink or source mode)

All

Io

0

12

Adc

Output Current Limit Inception (Hiccup Mode)

(current limit does not operate in sink mode)

All

IO, lim

130

% Io,max

Output Short-Circuit Current

All

IO, s/c

1.3

Arms

(VO≤250mV) ( Hiccup Mode )

Efficiency

VO,set = 0.6Vdc

η

70.8

%

VIN= 12Vdc, TA=25°C

VO, set = 1.2Vdc

η

81.5

%

IO=IO, max , VO= VO,set

VO,set = 1.8Vdc

η

85.7

%

VO,set = 2.5Vdc

η

88.3

%

VO, set = 3.3Vdc

η

90.1

%

VO,set = 5.0Vdc

η

92.5

%

Switching Frequency

All

fsw



800



kHz

1 External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best

transient response. See the Tunable LoopTM section for details.

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 4

Electrical Specifications (continued)

Parameter

Device

Symbol

Min

Typ

Max

Unit

Frequency Synchronization

All

Synchronization Frequency Range

All

760

800

840

kHz

High-Level Input Voltage

All

VIH

2

V

Low-Level Input Voltage

All

VIL

0.4

V

Input Current, SYNC

All

ISYNC

100

nA

Minimum Pulse Width, SYNC

All

tSYNC

100

ns

Maximum SYNC rise time

All

tSYNC_SH

100

ns

General Specifications

Parameter

Device

Min

Typ

Max

Unit

Calculated MTBF (IO=0.8IO, max, TA=40°C) Telecordia Issue 3 Method 1

Case 3

All

29,951,054

Hours

Weight



0.732



g (oz.)

Feature Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See

Feature Descriptions for additional information.

Parameter

Device

Symbol

Min

Typ

Max

Unit

On/Off Signal Interface

(VIN=VIN, min to VIN, max ; open collector or equivalent,

Signal referenced to GND)

Device code with suffix “4” – Positive Logic (See Ordering

Information)

Logic High (Module ON)

Input High Current

All

IIH



1

mA

Input High Voltage

All

VIH

2



VIN,max

V

Logic Low (Module OFF)

Input Low Current

All

IIL



1

mA

Input Low Voltage

All

VIL

-0.2



0.6

V

Device Code with no suffix – Negative Logic (See Ordering

Information)

(On/OFF pin is open collector/drain logic input with

external pull-up resistor; signal referenced to GND)

Logic High (Module OFF)

Input High Current

All

IIH

―

1

mA

Input High Voltage

All

VIH

2

―

VIN, max

Vdc

Logic Low (Module ON)

Input low Current

All

IIL

―

50

μA

Input Low Voltage

All

VIL

-0.2

―

0.6

Vdc

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 5

Feature Specifications (cont.)

Parameter

Device

Symbol

Min

Typ

Max

Units

Turn-On Delay and Rise Times

(VIN=VIN, nom, IO=IO, max , VO to within ±1% of steady state)

Case 1: On/Off input is enabled and then input power is

applied (delay from instant at which VIN = VIN, min until Vo =

10% of Vo, set)

All

Tdelay

―

0.9

―

msec

Case 2: Input power is applied for at least one second and

then the On/Off input is enabled (delay from instant at

which Von/Off is enabled until Vo = 10% of Vo, set)

All

Tdelay

―

0.8

―

msec

Output voltage Rise time (time for Vo to rise from

10% of Vo, set to 90% of Vo, set)

All

Trise

―

2

―

msec

Output voltage overshoot (TA = 25oC

VIN= VIN, min to VIN, max,IO = IO, min to IO, max)

With or without maximum external capacitance

3

% VO,

set

Over Temperature Protection

(See Thermal Considerations section)

All

Tref

130

°C

Tracking Accuracy (Power-Up: 2V/ms)

All

VSEQ –Vo

100

mV

(Power-Down: 2V/ms)

All

VSEQ –Vo

100

mV

(VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo)

Input Undervoltage Lockout

Turn-on Threshold

All

3

Vdc

Turn-off Threshold

All

2.75

Vdc

Hysteresis

All

0.25

Vdc

PGOOD (Power Good)

Signal Interface Open Drain, Vsupply  5VDC

Overvoltage threshold for PGOOD ON

All

108

%VO, set

Overvoltage threshold for PGOOD OFF

All

110

%VO, set

Undervoltage threshold for PGOOD ON

All

92

%VO, set

Undervoltage threshold for PGOOD OFF

All

90

%VO, set

Pulldown resistance of PGOOD pin

All

50



Sink current capability into PGOOD pin

All

5

mA

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 6

Characteristic Curves

The following figures provide typical characteristics for the 12A Analog Pico SlimLynxTM at 0.6Vo and 25oC.

EFFICIENCY,  (%)

OUTPUT CURRENT, Io (A)

OUTPUT CURRENT, IO (A)

AMBIENT TEMPERATURE, TA OC

Figure 1. Converter Efficiency versus Output Current.

Figure 2. Derating Output Current versus Ambient

Temperature and Airflow.

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (5Adiv) VO (V) (10mV/div)

TIME, t (500ns/div)

TIME, t (20s /div)

Figure 3. Typical output ripple (CO=2x47μF ceramic, VIN =

12V, Io = Io,max, 20MHz BW).

Figure 4. Transient Response to Dynamic Load Change from

50% to 100% at 12Vin, Cout=4x47uF+6x330uF, CTune=47nF,

RTune=300

OUTPUT VOLTAGE ON/OFF VOLTAGE

VO (V) (200mV/div) VON/OFF (V) (5V/div)

OUTPUT VOLTAGE INPUT VOLTAGE

VO (V) (200mV/div) VIN (V) (5V/div)

TIME, t (2ms/div)

Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max).

Figure 6. Typical Start-up Using Input Voltage (VIN = 12V, Io =

Io,max).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 7

Characteristic Curves

The following figures provide typical characteristics for the 12A Analog Pico SlimLynxTM at 1.2Vo and 25oC.

EFFICIENCY,  (%)

OUTPUT CURRENT, Io (A)

OUTPUT CURRENT, IO (A)

AMBIENT TEMPERATURE, TA OC

Figure 7. Converter Efficiency versus Output Current.

Figure 8. Derating Output Current versus Ambient

Temperature and Airflow.

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT OUTPUT VOLTAGE

IO (A) (5Adiv) VO (V) (10mV/div)

TIME, t (500ns/div)

TIME, t (20s /div)

Figure 9. Typical output ripple (CO=2x47μF ceramic, VIN =

12V, Io = Io,max, 20MHz BW ).

Figure 10. Transient Response to Dynamic Load Change from

50% to 100% at 12Vin, Cout=4x47uF+3x330uF, CTune=10nF,

RTune=300

OUTPUT VOLTAGE ON/OFF VOLTAGE

VO (V) (300mV/div) VON/OFF (V) (5V/div)

OUTPUT VOLTAGE INPUT VOLTAGE

VO (V) (300mV/div) VIN (V) (5V/div)

TIME, t (2ms/div)

Figure 11. Typical Start-up Using On/Off Voltage (Io = Io,max).

Figure 12. Typical Start-up Using Input Voltage (VIN = 12V, Io =

Io,max).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 8

Characteristic Curves

The following figures provide typical characteristics for the 12A Analog Pico SlimLynxTM at 1.8Vo and 25oC.

EFFICIENCY,  (%)

OUTPUT CURRENT, Io (A)

OUTPUT CURRENT, IO (A)

AMBIENT TEMPERATURE, TA OC

Figure 13. Converter Efficiency versus Output Current.

Figure 14. Derating Output Current versus Ambient

Temperature and Airflow.

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (5Adiv) VO (V) (20mV/div)

TIME, t (500ns/div)

TIME, t (20s /div)

Figure 15. Typical output ripple (CO=2x47μF ceramic, VIN =

12V, Io = Io,max, 20MHz BW ).

Figure 16. Transient Response to Dynamic Load Change from

50% to 100% at 12Vin, Cout=4x47uF+2x330uF, CTune=8.2nF,

RTune=300

OUTPUT VOLTAGE ON/OFF VOLTAGE

VO (V) (500mV/div) VON/OFF (V) (5V/div)

OUTPUT VOLTAGE INPUT VOLTAGE

VO (V) (500mV/div) VIN (V) (5V/div)

TIME, t (2ms/div)

Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max).

Figure 18. Typical Start-up Using Input Voltage (VIN = 12V, Io =

Io,max).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 9

Characteristic Curves

The following figures provide typical characteristics for the 12A Analog Pico SlimLynxTM at 2.5Vo and 25oC.

EFFICIENCY,  (%)

OUTPUT CURRENT, Io (A)

OUTPUT CURRENT, IO (A)

AMBIENT TEMPERATURE, TA OC

Figure 19. Converter Efficiency versus Output Current.

Figure 20. Derating Output Current versus Ambient

Temperature and Airflow.

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (5Adiv) VO (V) (50mV/div)

TIME, t (500ns/div)

TIME, t (20s /div)

Figure 21. Typical output ripple (CO=2x47μF ceramic, VIN =

12V, Io = Io,max, 20MHz BW ).

Figure 22. Transient Response to Dynamic Load Change from

50% to 100% at 12Vin, Cout=4x47uF+1x330uF, CTune=2700p,

RTune=300

OUTPUT VOLTAGE ON/OFF VOLTAGE

VO (V) (1V/div) VON/OFF (V) (5V/div)

OUTPUT VOLTAGE INPUT VOLTAGE

VO (V) (1V/div) VIN (V) (5V/div)

TIME, t (2ms/div)

Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max).

Figure 24. Typical Start-up Using Input Voltage (VIN = 12V, Io =

Io,max).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 10

Characteristic Curves

The following figures provide typical characteristics for the 12A Analog Pico SlimLynxTM at 3.3Vo and 25oC.

EFFICIENCY,  (%)

OUTPUT CURRENT, Io (A)

OUTPUT CURRENT, IO (A)

AMBIENT TEMPERATURE, TA OC

Figure 25. Converter Efficiency versus Output Current.

Figure 26. Derating Output Current versus Ambient

Temperature and Airflow.

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (5Adiv) VO (V) (50mV/div)

TIME, t (500ns/div)

TIME, t (20s /div)

Figure 27. Typical output ripple and noise (CO=2x47μF

ceramic, VIN = 12V, Io = Io,max, 20MHz BW ).

Figure 28 Transient Response to Dynamic Load Change from

50% to 100% at 12Vin, Cout=3x47uF+1x330uF,

CTune=1800pF, RTune=300

OUTPUT VOLTAGE ON/OFF VOLTAGE

VO (V) (1V/div) VON/OFF (V) (5V/div)

OUTPUT VOLTAGE INPUT VOLTAGE

VO (V) (1V/div) VIN (V) (5V/div)

TIME, t (2ms/div)

Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max).

Figure 30. Typical Start-up Using Input Voltage (VIN = 12V, Io =

Io,max).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 11

Characteristic Curves

The following figures provide typical characteristics for the 12A Analog Pico SlimLynxTM at 5Vo and 25oC.

EFFICIENCY,  (%)

OUTPUT CURRENT, Io (A)

OUTPUT CURRENT, IO (A)

AMBIENT TEMPERATURE, TA OC

Figure 31. Converter Efficiency versus Output Current.

Figure 32. Derating Output Current versus Ambient

Temperature and Airflow.

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT OUTPUT VOLTAGE

IO (A) (5Adiv) VO (V) (50mV/div)

TIME, t (500ns/div)

TIME, t (20s /div)

Figure 33. Typical output ripple and noise (CO=2x47μF

ceramic, VIN = 12V, Io = Io,max, 20MHz BW ).

Figure 34. Transient Response to Dynamic Load Change from

50% to 100% at 12Vin, Cout=6x47uF, CTune=1200pF,

RTune=300

OUTPUT VOLTAGE ON/OFF VOLTAGE

VO (V) (2V/div) VON/OFF (V) (5V/div)

OUTPUT VOLTAGE INPUT VOLTAGE

VO (V) (2V/div) VIN (V) (5V/div)

TIME, t (2ms/div)

Figure 35. Typical Start-up Using On/Off Voltage (Io = Io,max).

Figure 36. Typical Start-up Using Input Voltage (VIN = 12V, Io =

Io,max).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 12

Design Considerations

Input Filtering

The 12A Analog Pico SlimLynxTM Open Frame module

should be connected to a low ac-impedance source. A

highly inductive source can affect the stability of the

module. An input capacitance must be placed directly

adjacent to the input pin of the module, to minimize input

ripple voltage and ensure module stability.

To minimize input voltage ripple, ceramic capacitors are

recommended at the input of the module. Figure 37 shows

the input ripple voltage for various output voltages at 12A

of load current with 1x22 µF or 2x22 µF ceramic

capacitors and an input of 12V.

Figure 37. Input ripple voltage for various output

voltages with 1x22 µF or 2x22 µF ceramic capacitors at

the input (12A load). Input voltage is 12V (20MHz BW)

Output Filtering

These modules are designed for low output ripple voltage

and will meet the maximum output ripple specification with

3x0.047 µF ceramic and 2x47 µF ceramic capacitors at the

output of the module. However, additional output filtering

may be required by the system designer for a number of

reasons. First, there may be a need to further reduce the

output ripple and noise of the module. Second, the dynamic

response characteristics may need to be customized to a

particular load step change.

To reduce the output ripple and improve the dynamic

response to a step load change, additional capacitance at

the output can be used. Low ESR polymer and ceramic

capacitors are recommended to improve the dynamic

response of the module. Figure 38 provides output ripple

information, measured with a scope with its Bandwidth

limited to 20MHz for different external capacitance values at

various Vo and a full load current of 12A. For stable

operation of the module, limit the capacitance to less than

the maximum output capacitance as specified in the

electrical specification table. Optimal performance of the

module can be achieved by using the Tunable LoopTM feature

described later in this data sheet.

Figure 38. Output ripple voltage for various output

voltages with external 2x47 µF, 4x47 µF, 6x47 µF or 8x47

µF ceramic capacitors at the output (12A load). Input

voltage is 12V. (20MHz BW)

Safety Considerations

For safety agency approval the power module must be

installed in compliance with the spacing and separation

requirements of the end-use safety agency standards, i.e.,

UL 60950-1 2nd, CSA C22.2 No. 60950-1-07, DIN EN 60950-

1:2006 + A11 (VDE0805 Teil 1 + A11):2009-11; EN 60950-

1:2006 + A11:2009-03.

For the converter output to be considered meeting the

requirements of safety extra-low voltage (SELV), the input

must meet SELV requirements. The power module has

extra-low voltage (ELV) outputs when all inputs are ELV.

The input to these units is to be provided with a fast-acting

fuse (e.g. ABC Bussmann) with a maximum rating of 20 A in

the positive input lead.

0

50

100

150

200

250

300

350

400

450

0.5 1 1.5 2 2.5 3 3.5 4 4.5 5

Ripple (mVp-p)

Output Voltage(Volts)

1x22uF

2x22 uF

0

20

40

60

80

0.5 1 1.5 2 2.5 3 3.5 4 4.5 5

Ripple (mVp-p)

Output Voltage(Volts)

1x47uF Ext Cap

2x47uF Ext Cap

3x47uF Ext Cap

4x47uF Ext Cap

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 13

Analog Feature Descriptions

Remote On/Off

The 12A Analog Pico SlimLynxTM Open Frame power modules

feature an On/Off pin for remote On/Off operation. Two

On/Off logic options are available. In the Positive Logic

On/Off option, (device code suffix “4” – see Ordering

Information), the module turns ON during a logic High on the

On/Off pin and turns OFF during a logic Low. With the

Negative Logic On/Off option, (no device code suffix, see

Ordering Information), the module turns OFF during logic

High and ON during logic Low. The On/Off signal should be

always referenced to ground. For either On/Off logic option,

leaving the On/Off pin disconnected will turn the module ON

when input voltage is present.

For positive logic modules, the circuit configuration for using

the On/Off pin is shown in Figure 39. When the external

transistor Q1 is in the OFF state, the internal diode is turned

OFF. This keeps the internal Enable signal to be pulled up by

the internal 3.3V, thus turning/keeping the module ON. When

transistor Q1 is turned ON, the internal diode conducts and

Enable signal is pulled low and the module is OFF.

For negative logic On/Off modules, the circuit configuration is

shown in Fig. 40. The On/Off pin should be pulled high with

an external pull-up resistor. When transistor Q1 is in the OFF

state, the On/Off pin is pulled high, transistor Q2 is turned ON.

This pulls the internal ENABLE low and the module is OFF. To

turn the module ON, Q1 is turned ON pulling the On/Off pin

low, turning transistor Q2 OFF, which results in the PWM

Enable pin going high.

Figure 39. Circuit configuration for using positive On/Off

logic.

Figure 40. Circuit configuration for using negative On/Off

logic.

Monotonic Start-up and Shutdown

The module has monotonic start-up and shutdown behavior

for any combination of rated input voltage, output current

and operating temperature range.

Startup into Pre-biased Output

The module can start into a prebiased output as long as the

prebias voltage is 0.5V less than the set output voltage.

Analog Output Voltage Programming

The output voltage of the module is programmable to any

voltage from 0.6dc to 5.5Vdc by connecting a resistor

between the Trim and SIG_GND pins of the module. Certain

restrictions apply on the output voltage set point depending

on the input voltage. These are shown in the Output Voltage

vs. Input Voltage Set Point Area plot in Fig. 41. The Upper

Limit curve shows that for output voltages lower than 1V, the

input voltage must be lower than the maximum of 14.4V. The

Lower Limit curve shows that for output voltages higher than

0.6V, the input voltage needs to be larger than the minimum

of 3V.

Figure 41. Output Voltage vs. Input Voltage Set Point Area

plot showing limits where the output voltage can be set for

different input voltages.

10K

Q1

22K

Q2

22K

Rpullup

+3.3V

+VIN

GND

_

+

I

ON/OFF

V

ON/OFF

ENABLE

SLIMLYNX MODULE

10K

Q1

Rpullup

+3.3V

+VIN

GND

_

+

I

ON/OFF

V

ON/OFF

ENABLE

SLIMLYNX MODULE

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 14

VO(+)

TRIM

VS─

Rtrim

LOAD

VIN(+)

ON/OFF

VS+

SIG_GND

Caution – Do not connect SIG_GND to GND elsewhere in the

layout

Figure 42. Circuit configuration for programming output

voltage using an external resistor.

Without an external resistor between Trim and SIG_GND pins,

the output of the module will be 0.6Vdc.To calculate the

value of the trim resistor, Rtrim for a desired output voltage,

should be as per the following equation:

 

















k

Vo

Rtrim 6.0

12

Rtrim is the external resistor in kΩ

Vo is the desired output voltage.

Table 1 provides Rtrim values required for some common

output voltages.

Table 1

VO, set (V)

Rtrim (KΩ)

0.6

Open

0.9

40

1.0

30

1.2

20

1.5

13.33

1.8

10

2.5

6.316

3.3

4.444

5.0

2.727

Remote Sense

The power module has a Remote Sense feature to minimize

the effects of distribution losses by regulating the voltage

between the sense pins (VS+ and VS-). The voltage drop

between the sense pins and the VOUT and GND pins of the

module should not exceed 0.5V.

Analog Voltage Margining

Output voltage margining can be implemented in the

module by connecting a resistor, Rmargin-up, from the Trim pin

to the ground pin for margining-up the output voltage and

by connecting a resistor, Rmargin-down, from the Trim pin to

output pin for margining-down. Figure 43 shows the circuit

configuration for output voltage margining. The POL

Programming Tool, available at www.gecriticalpower.com

under the Downloads section, also calculates the values of

Rmargin-up and Rmargin-down for a specific output voltage and %

margin. Please consult your local GE Critical Power

technical representative for additional details.

Figure 43. Circuit Configuration for margining Output

voltage.

Output Voltage Sequencing

The power module includes a sequencing feature, EZ-

SEQUENCE that enables users to implement various types of

output voltage sequencing in their applications. This is

accomplished via an additional sequencing pin. When not

using the sequencing feature, leave it unconnected.

The voltage applied to the SEQ pin should be scaled down by

the same ratio as used to scale the output voltage down to

the reference voltage of the module. This is accomplished by

an external resistive divider connected across the

sequencing voltage before it is fed to the SEQ pin as shown

in Fig. 44. In addition, a small capacitor (suggested value

100pF) should be connected across the lower resistor R1.

For all SlimLynx modules, the minimum recommended delay

between the ON/OFF signal and the sequencing signal is

10ms to ensure that the module output is ramped up

according to the sequencing signal. This ensures that the

module soft-start routine is completed before the

sequencing signal is allowed to ramp up.

Vo

MODULE

SIG_GND

Trim

Q1

Rtrim

Rmargin-up

Q2

Rmargin-down

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 15

Figure 44. Circuit showing connection of the sequencing

signal to the SEQ pin.

When the scaled down sequencing voltage is applied to the

SEQ pin, the output voltage tracks this voltage until the

output reaches the set-point voltage. The final value of the

sequencing voltage must be set higher than the set-point

voltage of the module. The output voltage follows the

sequencing voltage on a one-to-one basis. By connecting

multiple modules together, multiple modules can track their

output voltages to the voltage applied on the SEQ pin.

The module’s output can track the SEQ pin signal with slopes

of up to 0.5V/msec during power-up or power-down.

To initiate simultaneous shutdown of the modules, the SEQ

pin voltage is lowered in a controlled manner. The output

voltage of the modules tracks the voltages below their set-

point voltages on a one-to-one basis. A valid input voltage

must be maintained until the tracking and output voltages

reach ground potential.

Overcurrent Protection

To provide protection in a fault (output overload) condition,

the unit is equipped with internal current-limiting circuitry

and can endure current limiting continuously. At the point of

current-limit inception, the unit enters hiccup mode. The unit

operates normally once the output current is brought back

into its specified range.

Overtemperature Protection

To provide protection in a fault condition, the unit is

equipped with a thermal shutdown circuit. The unit will shut

down if the overtemperature threshold of 150oC(typ) is

exceeded at the thermal reference point Tref .Once the unit

goes into thermal shutdown it will then wait to cool before

attempting to restart.

Input Undervoltage Lockout

At input voltages below the input undervoltage lockout limit,

the module operation is disabled. The module will begin to

operate at an input voltage above the undervoltage lockout

turn-on threshold.

Synchronization

The module switching frequency can be synchronized to a

signal with an external frequency within a specified range.

Synchronization can be done by using the external signal

applied to the SYNC pin of the module as shown in Fig. 45,

with the converter being synchronized by the rising edge of

the external signal. The Electrical Specifications table

specifies the requirements of the external SYNC signal. If the

SYNC pin is not used, the module should free run at the

default switching frequency. If synchronization is not being

used, connect the SYNC pin to GND.

MODULE

SYNC

GND

+

─

Figure 45. External source connections to synchronize

switching frequency of the module.

Tunable LoopTM

The module has a feature that optimizes transient response

of the module called Tunable LoopTM.

External capacitors are usually added to the output of the

module for two reasons: to reduce output ripple and noise

(see Figure 38) and to reduce output voltage deviations from

the steady-state value in the presence of dynamic load

current changes. Adding external capacitance however

affects the voltage control loop of the module, typically

causing the loop to slow down with sluggish response.

Larger values of external capacitance could also cause the

module to become unstable.

The Tunable LoopTM allows the user to externally adjust the

voltage control loop to match the filter network connected

to the output of the module. The Tunable LoopTM is

implemented by connecting a series R-C between the VS+

and TRIM pins of the module, as shown in Fig. 46. This R-C

allows the user to externally adjust the voltage loop

feedback compensation of the module.

Figure. 46. Circuit diagram showing connection of RTUME

and CTUNE to tune the control loop of the module

VS+

MODULE

SIG_GND

TRIM

VOUT

RTune

CTune

RTrim

CO

GND

100 pF

SlimLynx Module

R1=Rtrim

20K

SIG_GND

SEQ

V

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 16

Recommended values of RTUNE and CTUNE for different output

capacitor combinations are given in Table 2. Table 2 shows

the recommended values of RTUNE and CTUNE for different

values of ceramic output capacitors up to 1000uF that

might be needed for an application to meet output ripple

and noise requirements. Selecting RTUNE and CTUNE according

to Table 2 will ensure stable operation of the module.

In applications with tight output voltage limits in the

presence of dynamic current loading, additional output

capacitance will be required. Table 3 lists recommended

values of RTUNE and CTUNE in order to meet 2% output

voltage deviation limits for some common output voltages

in the presence of a 6A to 12A step change (50% of full load),

with an input voltage of 12V.

Please contact your GE Critical Power technical

representative to obtain more details of this feature as well

as for guidelines on how to select the right value of external

R-C to tune the module for best transient performance and

stable operation for other output capacitance values.

Table 2. General recommended values of of RTUNE and CTUNE

for Vin=12V and various external ceramic capacitor

combinations.

Table 3. Recommended values of RTUNE and CTUNE to obtain

transient deviation of 2% of Vout for a 6A step load with

Vin=12V.

Vo

5V

3.3V

2.5V

1.8V

1.2V

0.6V

Co

6x47F

Ceramic

3x47F+

1x330F

Polymer

4x47F+

1x330F

Polymer

4x47F +

2x330F

Polymer

4x47F +

3x330F

Polymer

3x47F +

3x330F

Polymer

RTUNE

300

CTUNE

1200pF

1800pF

2700pF

8200pF

10nF

47nF

V

89mV

62mV

49mV

33mV

24mV

11mV

Note: The capacitors used in the Tunable Loop tables are

47 μF/2 mΩ ESR ceramic and 330 μF/9 mΩ ESR polymer

capacitors.

Power Good

The module provides a Power Good (PGOOD) signal that is

implemented with an open-drain output to indicate that the

output voltage is within the regulation limits of the power

module. The PGOOD signal will be de-asserted to a low state

if any condition such as over temperature, overcurrent or

loss of regulation occurs that would result in the output

voltage going outside the specified thresholds.

The PGOOD terminal can be connected through a pullup

resistor (suggested value 100K) to a source of 5VDC or

lower.

Co

3x47F

4x47F

6x47F

10x47F

20x47F

RTUNE

300

CTUNE

680pF

820pF

1200pF

2700pF

5600pF

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 17

Thermal Considerations

Power modules operate in a variety of thermal environments;

however, sufficient cooling should always be provided to help

ensure reliable operation.

Considerations include ambient temperature, airflow, module

power dissipation, and the need for increased reliability. A

reduction in the operating temperature of the module will

result in an increase in reliability. The thermal data

presented here is based on physical measurements taken in

a wind tunnel. The test set-up is shown in Figure 47. The

preferred airflow direction for the module is in Figure 48.

Air

flow

x

Power Module

Wind Tunnel

PWBs

12.7_

(0.50)

76.2_

(3.0)

Probe Location

for measuring

airflow and

ambient

temperature

25.4_

(1.0)

Figure 47. Thermal Test Setup.

The thermal reference points, Tref used in the specifications

are also shown in Figure 48. For reliable operation the

temperatures at the Q3 should not exceed 120oC and the

temperature at L1 core should not exceed 125°C. The output

power of the module should not exceed the rated power of

the module (Vo,set x Io,max).

Please refer to the Application Note “Thermal

Characterization Process For Open-Frame Board-Mounted

Power Modules” for a detailed discussion of thermal

aspects including maximum device temperatures.

Figure 48. Preferred airflow direction and location of hot-

spot of the module (Tref).

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 18

Example Application Circuit

Requirements:

Vin: 12V

Vout: 1.8V

Iout: 9A max., worst case load transient is from 6A to 9A

Vout: 1.5% of Vout (27mV) for worst case load transient

Vin, ripple 1.5% of Vin (180mV, p-p)

CI1 Decoupling cap - 1x0.047F/16V ceramic capacitor (e.g. Murata LLL185R71C473MA01)

CI2 2x22F/16V ceramic capacitor (e.g. Murata GRM32ER61C226KE20)

CI3 470F/16V bulk electrolytic

CO1 Decoupling cap - 1x0.047F/16V ceramic capacitor (e.g. Murata LLL185R71C473MA01) + 1x0.047uF/16V

0402size ceramic capacitor

CO2 3x47F/16V ceramic capacitor (e.g. Murata GRM32ER61C226KE20)

CO3 1x330F/6V POSCAP

CTune 3900pF ceramic capacitor (can be 1206, 0805 or 0603 size)

RTune 300 ΩSMT resistor (can be 1206, 0805 or 0603 size)

RTrim 10k SMT resistor (can be 1206, 0805 or 0603 size, recommended tolerance of 0.1%)

Note: The DATA, CLK and SMBALRT pins do not have any pull-up resistors inside the module. Typically, the SMBus master

controller will have the pull-up resistors as well as provide the driving source for these signals.

SEQ

VS-

GND

Vin+

CI3

CO3

VOUT

VS+

GND

TRIM

CTUNE

RTUNE

RTrim

VIN

CO1

CI1

Vout+

ON/OFF

MODULE

PGOOD

SIG_GND

SYNC

CI2

CO2

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 19

Mechanical Outline

Dimensions are in millimeters and (inches).

Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [unless otherwise indicated]

x.xx mm  0.25 mm (x.xxx in  0.010 in.)

2 If unused, connect to Ground

FUNCTION

1

ON/OFF

10

PGOOD

2

VIN

11

SYNC2

3

GND

12

VS-

4

VOUT

13

SIG_GND

5

VS+ (SENSE)

14

NC

6

TRIM

15

NC

7

GND

16

NC

8

NC

17

NC

9

SEQ

NC

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 20

Recommended Pad Layout

Dimensions are in millimeters and (inches).

Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [unless otherwise indicated]

x.xx mm  0.25 mm (x.xxx in  0.010 in.)

2 If unused, connect to Ground

FUNCTION

1

ON/OFF

10

PGOOD

2

VIN

11

SYNC2

3

GND

12

VS-

4

VOUT

13

SIG_GND

5

VS+ (SENSE)

14

NC

6

TRIM

15

NC

7

GND

16

NC

8

NC

17

NC

9

SEQ

NC

NC NC

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 21

Packaging Details

The 12V Analog Pico SlimLynxTM 12A Open Frame modules are supplied in tape & reel as standard. Modules are shipped in

quantities of 600 modules per reel.

All Dimensions are in millimeters and (in inches).

Reel Dimensions:

Outside Dimensions: 330.2 mm (13.00)

Inside Dimensions: 177.8 mm (7.00”)

Tape Width: 24.00 mm (0.945”)

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

November 4, 2016

Page 22

Surface Mount Information

Pick and Place

The 12A Analog Pico SlimLynxTM Open Frame modules use an

open frame construction and are designed for a fully

automated assembly process. The modules are fitted with a

label designed to provide a large surface area for pick and

place operations. The label meets all the requirements for

surface mount processing, as well as safety standards, and is

able to withstand reflow temperatures of up to 300oC. The

label also carries product information such as product code,

serial number and the location of manufacture.

Nozzle Recommendations

The module weight has been kept to a minimum by using

open frame construction. Variables such as nozzle size, tip

style, vacuum pressure and placement speed should be

considered to optimize this process. The minimum

recommended inside nozzle diameter for reliable operation is

3mm. The maximum nozzle outer diameter, which will safely

fit within the allowable component spacing, is 7 mm.

Lead Free Soldering

The modules are lead-free (Pb-free) and RoHS compliant and

fully compatible in a Pb-free soldering process. Failure to

observe the instructions below may result in the failure of or

cause damage to the modules and can adversely affect

long-term reliability.

Pb-free Reflow Profile

Power Systems will comply with J-STD-020 Rev. D

(Moisture/Reflow Sensitivity Classification for Nonhermetic

Solid State Surface Mount Devices) for both Pb-free solder

profiles and MSL classification procedures. This standard

provides a recommended forced-air-convection reflow

profile based on the volume and thickness of the package

(table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu

(SAC). The recommended linear reflow profile using Sn/Ag/Cu

solder is shown in Fig. 50. Soldering outside of the

recommended profile requires testing to verify results and

performance.

MSL Rating

The 12A Analog Pico SlimLynxTM Open Frame modules have a

MSL rating of 2a.

Storage and Handling

The recommended storage environment and handling

procedures for moisture-sensitive surface mount packages is

detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and

Use of Moisture/Reflow Sensitive Surface Mount Devices).

Moisture barrier bags (MBB) with desiccant are required for

MSL ratings of 2 or greater. These sealed packages should

not be broken until time of use. Once the original package is

broken, the floor life of the product at conditions of  30°C

and 60% relative humidity varies according to the MSL rating

(see J-STD-033A). The shelf life for dry packed SMT packages

will be a minimum of 12 months from the bag seal date,

when stored at the following conditions: < 40° C, < 90%

relative humidity.

Figure 50. Recommended linear reflow profile using

Sn/Ag/Cu solder.

Post Solder Cleaning and Drying Considerations

Post solder cleaning is usually the final circuit-board

assembly process prior to electrical board testing. The result

of inadequate cleaning and drying can affect both the

reliability of a power module and the testability of the

finished circuit-board assembly. For guidance on

appropriate soldering, cleaning and drying procedures, refer

to Board Mounted Power Modules: Soldering and Cleaning

Application Note (AN04-001).

Per J-STD-020 Rev. D

0

50

100

150

200

250

300

Reflow Time (Seconds)

Reflow Temp (°C)

Heating Zone

1°C/Second

Peak Temp 260°C

* Min. Time Above 235°C

15 Seconds

*Time Above 217°C

60 Seconds

Cooling

Zone

GE

Data Sheet

12A Analog Pico SlimLynxTM Open Frame: Non-Isolated DC-DC Power

Modules

3Vdc –14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current

Contact Us

For more information, call us at

USA/Canada:

+1 877 546 3243, or +1 972 244 9288

Asia-Pacific:

+86.021.54279977*808

Europe, Middle-East and Africa:

+49.89.878067-280

www.gecriticalpower.com

GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no

liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s)

or information.

November 4, 2016

Version 1.5

Ordering Information

Please contact your GE Sales Representative for pricing, availability and optional features.

Table 4. Device Codes

Device Code

Input

Voltage Range

Output

Voltage

Output

Current

On/Off

Logic

Sequencing

Comcodes

PNVT012A0X3-SRZ

3 – 14.4Vdc

0.6 – 5.5 Vdc

12A

Negative

Yes

150038561

PNVT012A0X43-SRZ

3 – 14.4Vdc

0.6 – 5.5 Vdc

12A

Positive

Yes

150038562

-Z refers to RoHS compliant parts

Table 5. Coding Scheme

Package

Identifier

Family

Sequencing

Option

Output

current

Output

voltage

On/Off

logic

Remote

Sense

Options

ROHS Compliance

P

NV

T

012A0

X

3

-SR

Z

P=Pico

U=Micro

M=Mega

G=Giga

NV=SlimLynx

Analog Open

Frame

T=with EZ

Sequence

X=without

sequencing

12A

X =

programm

able output

4 =

positive

No entry =

negative

3 = Remote

Sense

S = Surface

Mount

R = Tape &

Reel

Z = ROHS6