REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Update to reflect latest changes in format and requirement s. Editorial changes
throughout. -les
01-05-22
Ray m ond Monnin
B
Update drawing to current requirements. Editorial changes t hroughout . - gap
08-12-12
Robert M. Heber
The original first sheet of this draw ing has been replaced.
REV
SHEET
REV
SHEET
REV STATUS REV B B B B B B B B B
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9
PMIC N/A PREPARED BY
Thanh V. Nguyen
DEFENSE SUPPLY CENTER COLUMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Thanh V. Nguyen
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Monica L. Poelking
MICROCI RCUIT, DIGITAL, BIPOLAR, ADVANCED
SCHOTTKY TTL, 2-INPUT NAND SCHMITT
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
93-02-18
TRIGGER, MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
B SIZE
A CAGE CODE
67268
5962-89487
SHEET
1 OF
9
DSCC FORM 2233
APR 97 5962-E275-08
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-89487 01 C X
Drawing number Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function
01 54F132 Quad 2-input NAND Schmitt trigger
1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
C GDIP1-T14 or CDIP2-T14 14 Dual-in-line
D GDFP1-F14 or CDFP2-F14 14 Flat package
2 CQCC1-N20 20 Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage range ..................................................................... -0.5 V dc to minimum to +7.0 V dc maximum
Input voltage range (VIN) ............................................................... -0.5 V dc to minimum to +7.0 V dc maximum
Input current range ........................................................................ -30.0 mA to +5.0 mA
Voltage applied to output in high output state range ..................... -0.5 V to VCC
Current applied to output in low output state ................................. 40 mA
Storage temperature range ........................................................... -65C to +150C
Maximum power dissipation (PD) 1/ ............................................... 99.0 mW
Lead temperature (soldering, 10 seconds) .................................... +300C
Thermal resistance, junction-to-case (C) ..................................... See MIL-STD-1835
Junction temperature (TJ) .............................................................. +175C
1.4 Recommended operating conditions.
Supply voltage range (VCC) ........................................................... +4.5 V dc to +5.5 V dc
Maximum input clamp current (IIK) ................................................ -18 mA
Maximum high level output current (IOH) ....................................... -1.0 mA
Maximum low level output current (IOL) ......................................... 20 mA
Case operating temperature range (TC) ........................................ -55C to +125C
_________
1/ Power dissipation is defined as VCC x ICC and must withstand the added PD due to short circuit test, e.g., IOS.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 4
DSCC FORM 2234
APR 97
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
(2) TA = +125C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions
-55C TC +125C
Group A
subgroups
Limits Unit
unless otherwise specified Min Max
Positive-going threshold voltage
VT+ V
CC = 5.0 V 1, 2, 3 1.45 2.0 V
Negative-going threshold voltage
VT- 1, 2, 3 0.7 1.05 V
Input clamp voltage
VT 1, 2, 3 0.4 V
High level output voltage VOH V
CC = 4.5 V, VIL = 0.7 V,
IOH = -1.0 mA 1, 2, 3 2.5 V
Low level output voltage
VOL VCC = 4.5 V, IOL = 20 mA
VIH = 2.0 V 1, 2, 3 0.5 V
Input clamp voltage
VIK 1, 2, 3 -1.2 V
High level input current
IIH1 V
CC = 5.5 V VIN = 2.7 V 1, 2, 3 20 A
I
IH2 V
IN = 7.0 V
1, 2, 3 100 A
Low level input current
IIL V
CC = 5.5 V, VIN = 0.5 V , 1, 2, 3 -0.6 mA
Short circuit output current
IOS VCC = 5.5 V, VOUT = 0.0 V 1/ 1, 2, 3 -60 -150 mA
Supply current ICCH VCC = 5.5 V, VIN = 0.0 V
1, 2, 3 17 mA
ICCL VCC = 5.5 V, VIN = 5.5 V
1, 2, 3 18 mA
Functional tests
See 4.3.1c, VCC = 4.5 V, 5.5 V 7, 8
Propagation delay time,
An, Bn to nO tPLH V
CC = 5.0 V 9 4.0 11.0 ns
t
PLH V
CC = 4.5 V, 5.5 V 10, 11 2.0 13.0 ns
t
PHL V
CC = 5.0 V 9 4.5 12.5 ns
t
PHL
CL = 50 pF
RL = 500
See figure 3
VCC = 4.5 V, 5.5 V 10, 11 4.5 16.0 ns
1/ Not more than one output should be shorted at a time, and the duration of the short circuit condition should notexceed one
second.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 6
DSCC FORM 2234
APR 97
Case outlines C and D 2
Terminal
number Terminal Symbol
1 A0 NC
2 B0 A0
3 0O B0
4 A1 0O
5 B1 NC
6 1O A1
7 GND NC
8 3O B1
9 B3 1O
10 A3 GND
11 2O NC
12 B2 3O
13 A2 B
3
14 VCC A3
15 NC
16 2O
17 NC
18 B2
19 A2
20 VCC
FIGURE 1. Terminal connections.
Inputs Outputs
A B O
L L H
L H H
H L H
H H L
H = High level voltage.
L = Low level voltage.
FIGURE 2. Truth table.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 7
DSCC FORM 2234
APR 97
NOTES:
1. For the waveform, VM = 1.5 V.
2. RL = load resistor; see table I for value.
3. CL = load capacitance includes jig and probe capacitance; see table I for value.
4. All input pulses have the following characteristics: PRR = 1MHz, tr = tf = 2.5 ns, pulse
width = 500 ns, duty cycle = 50%.
FIGURE 3. Test circuit and switching waveforms.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 8
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004) - - -
Final electrical test parameters
(method 5004) 1*, 2, 3, 7, 8, 9
Group A test requirements
(method 5005) 1, 2, 3, 7, 8, 9, 10, 11
Groups C and D end-point
electrical parameters
(method 5005)
1, 2, 3
* PDA applies to subgroup 1.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
c. Subgroups 7 and 8 shall include verification of the truth table.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in method 1005 of MIL-STD-883.
(2) TA = +125C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-89487
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 9
DSCC FORM 2234
APR 97
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be
used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC
5962) should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of comp liance (see 3.6 herein) has been submitted to and accepted
by DSCC-VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 08-12-12
Approved sources of supply for SMD 5962-89487 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded
by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current
sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8948701CA 0C7V7 54F132DMQB
5962-8948701DA 0C7V7 54F132FMQB
5962-89487012A 0C7V7 54F132LMQB
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE Vendor name
number and address
0C7V7 QP Semiconductor
2945 Oakmead Village Court
Santa Clara, CA 95051
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
