LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 BluetoothTM Radio Check for Samples: LMX5252 FEATURES 1 * 2 * The LMX5252 provides a very compact radio solution for BluetoothTM applications that put extra strong requirements on low cost and small form factors. In addition, the application benefits from very low signal loss between the antenna and the radio. The radio completely integrates the receiver and transmitter baluns, the antenna switch, and filter together with the voltage-controlled oscillator (VCO) tank on one single die. The fractional-N delta-sigma synthesizer and the crystal offer support for a wide range of external reference frequency clocks or crystals. The digital Received Signal Strength Indicator (RSSI) allows for efficient power control and communication with Bluetooth Class 2 devices. Several current saving modes are available. * The baseband interface is completely digital and compatible with 8-pin bi-directional BlueRF using the RXMODE2 configuration. It can automatically adapt to the voltage levels used by different baseband controllers, independently of the supply voltage. APPLICATIONS * The LMX5252 is primarily targeting costsensitive consumer applications that require fast design-in, low power consumption and small designs. It is ideal for applications such as: - 2G, 2.5G, and 3G handsets - PDAs - Notebook PCs - Computer peripherals - Office network equipment - Home applications FUNCTIONAL BLOCK DIAGRAM 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Bluetooth is a trademark of Bluetooth SIG, Inc. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2013, Texas Instruments Incorporated LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. CONTENTS FEATURES ....................................................................................... ....................................................................................... 1 APPLICATIONS.................................................................................... .................................................................................... 1 DESCRIPTION .................................................................................... .................................................................................... 2 ELECTRICAL SPECIFICATIONS ...................................................................... ...................................................................... 4 ABSOLUTE MAXIMUM RATINGS ..................................................................... ..................................................................... 4 RECOMMENDED OPERATING CONDITIONS ........................................................... ........................................................... 5 DC ELECTRICAL CHARACTERISTICS, VCC = 2.75 V...................................................... ...................................................... 5 RF PERFORMANCE CHARACTERISTICS .............................................................. .............................................................. 6 RECEIVER PERFORMANCE CHARACTERISTICS ....................................................... ....................................................... 6 TRANSMITTER PERFORMANCE CHARACTERISTICS.................................................... .................................................... 7 SYNTHESIZER PERFORMANCE CHARACTERISTICS .................................................... .................................................... 7 CRYSTAL REQUIREMENTS ......................................................................... ......................................................................... 7 TYPICAL PERFORMANCE CHARACTERISTICS ........................................................ ........................................................ 13 FUNCTIONAL DESCRIPTION ....................................................................... ....................................................................... 17 APPLICATION INFORMATION....................................................................... ....................................................................... 20 PROGRAMMING DESCRIPTION..................................................................... ..................................................................... 21 Revision History................................................................................... ................................................................................... 35 DESCRIPTION The Texas Instruments LMX5252 Bluetooth Radio is a part of the third generation Bluetooth solution designed for use with short-range wireless applications. The radio integrates a complete Bluetooth Class 2 transceiver, operating in the ISM frequency band (2.4-2.5 GHz). The modulation is Gaussian Frequency Shift Keying (GF- SK) with a Bluetooth product of 0.5 and a modulation index ranging from 0.28 to 0.35. Fast frequency hopping (1600 hops/s) is used over a total of 79 channels between 2.402 GHz up to 2.480 GHz. The channel bandwidth is 1 MHz. The LMX5252 is designed in 0.18 m RF CMOS technology for small die size and low power consumption. The LMX5252 is available in a 6.0 mm x 6.0 mm 36 pin thin quad flatpack no lead (WQFN) package. 2 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 TP1/DIV2# TP2 TP3 TP4 GND ANT GND TP5 TP6 CONNECTION DIAGRAM 36 PINS WQFN 36 35 34 33 32 31 30 29 28 VCC 1 27 VCC GND 2 26 GND TE 3 25 VTUNE BXTLEN 4 24 GND LMX5252 RESET# 5 23 PLL_OUT VCC 6 22 GND GND 7 21 VCC 15 16 17 18 VREF_DIG 14 GND 13 32kIN 12 B3k2 11 BRCLK 10 BDATA_1 19 XO_N BDCLK BPKTCTL 9 BDATA 20 XO_P BDEN# BPOR 8 NOTE: Ground pad layout under ground slug of LMX5252 is required and must be soldered to the PCB ground. PIN FUNCTIONS PIN NAME NO. TYPE I DEFAULT LAYOUT DESCRIPTION VCC 1 VCC Power connection. GND 2 GND Ground connection. TE 3 NC BXTLEN 4 I Baseband RESET# 5 I Reset External reset (active low). VCC 6 I VCC Power connection. GND 7 GND Ground connection. BPOR 8 O NC BPKTCTL 9 I Baseband Access code indication from baseband controller. In transmit mode this controls the transmitter state, high = TX ON. In receive mode this controls the filter bandwidth, high = narrow, low = wide. BDEN# 10 I Baseband DBUS enable (active low). Latch enable, data latched from low to high. BDDATA 11 I/O Baseband DBUS data. BDCLK 12 I Baseband DBUS clock. Maximum 4 MHz. BDATA_1 13 I/O Baseband Transmit/receive Bluetooth data and sync signal for transmit. Scan test enable. Leave unconnected for normal operation. BRCLK enable. System clock enable signal (active high). Reset signal to baseband controller. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 3 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com PIN FUNCTIONS (continued) PIN TYPE DEFAULT LAYOUT 14 O Baseband B3k2 15 O NC 32kIN 16 I 32kHz Crystal GND 17 VREF_DI G 18 I IO Voltage XO_N 19 I/O Crystal Crystal negative input. XO_P 20 I/O Crystal Crystal positive input or external clock input. VCC 21 I GND 22 PLL_OUT 23 GND 24 VTUNE 25 GND 26 GND Ground connection. VCC 27 I VCC Power connection. TP6 28 I PLL_OUT TP5 29 NC GND 30 GND ANT 31 GND 32 TP4 33 NC TP3 34 GND Test point 3. Connect to ground. TP2 35 GND Test point 2. Connect to ground. TP1/DIV2# 36 NC NAME NO. BRCLK GND Buffered system clock output. Pin36 = high then same as crystal. Pin 36 = low then divide by 2 output. 3.2 kHz clock output. Connect to ground for normal operation. Optional 32.0 or 32.768 kHz Input frequency for generating 3.2KHz clk. Connect to ground for normal operation. Ground connection. Reference voltage for digital I/O. Control signals to baseband are level shifted depending on this input voltage. VCC Power connection. GND Ground connection. O Loop Filter Input I Loop Filter Output GND I/O DESCRIPTION Antenna GND Charge pump output to loop filter. Ground connection. VCO tune input from loop filter. Test point 6. Vtune calibration input. Pin with 0 ohm resistor for VTune. Test point 5. Do not connect. Ground connection. Antenna I/O. Ground connection. Test point 4. Do not connect. Not supported. ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS indicate limits beyond which damage to the device may occur. RECOMMENDED OPERATING CONDITIONS indicate conditions for which the device is intended to be functional, but do not specify specific performance limits. This device is a high performance RF integrated circuit and is ESD sensitive. Handling and assembly of this device should be performed at ESD free workstations. A 2 kV ESD rating applies to all pins. ABSOLUTE MAXIMUM RATINGS MIN MAX VCC Supply voltage -0.3 3.3 V VANT Applied voltage to ANT pin -0.3 1.95 V VI Applied voltage to all other pins -0.3 VCC + 0.3 V ILATCH Latchup current 100 ESDMM ESD Machine model (1) ESDHBM ESD Human Body PIN RF Input power TL Lead temperature (soldering) TS Storage temperature (1) 4 mA 200 V 2000 V 4 -65 UNIT dBm 260 C 150 C A 200V ESD rating applies to all pins except antenna pin (pin 31) = 150V. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 RECOMMENDED OPERATING CONDITIONS MIN TYP MAX VCC Supply Voltage (VCC) 2.5 2.75 3 UNIT V TA Temperature, Ambient. Fully functional Blue- tooth Mode -40 25 85 C HUMOP Humidity across operating temperature range 8%5 DC ELECTRICAL CHARACTERISTICS, VCC = 2.75 V PARAMETER MIN TYP MAX UNIT VREF_DIG Reference voltage 1.5 VCC V VIH Logical high input voltage 0.75xVCC 1.1xVCC V VIL Logical low input voltage -0.15xVCC 0.36xVCC V VOH Logical high output voltage VOL Logical low output voltage CINP 0.8xVCC 2.75 0 V 0.2xVCC V Input capacitance, digital pins 10 pF CL-DIG Load capacitance, digital pins 10 pF CL-AN Load capacitance, analog pins 25 pF ICC-L Input leakage current 5 A TRISE Rise/Fall time, digital inputs 20 ns TFALL Rise/Fall time, digital outputs ICC-PWDN Supply current in standby mode, XO Inactive ICC-XO Supply current in standby mode, XO Active ICC-RX Supply current in static RX mode ICC-TX Supply current in static TX mode 5 10 ns 28 50 A 271 A 39 47 mA 44 55 mA Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 5 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com RF PERFORMANCE CHARACTERISTICS In * * * * the performance characteristics tables the following applies: VCC = 2.75V unless otherwise specified. Temperature range from -40C to +85C unless otherwise specified. RF system performance specifications are specified on TI reference design platforms." All tests performed based on Bluetooth Test Specification rev 0.92. RECEIVER PERFORMANCE CHARACTERISTICS PARAMETER RXsense (2) PinRF Receive sensitivity TYP (1) MAX 2.402 GHz -80 -75 2.441 GHz -80 -75 2.480 GHz -80 -75 CONDITION BER < 0.001 MIN Maximum input level IMP (3) Intermodulation performance RSSI RSSI Dynamic range at LNA input ZRFIN (4) Input impedance of RF port (RF_inout) F1 = + 3 MHz, F2 = + 6 MHz, PinRF = -64 dBm OOB (1) (2) (3) (4) (5) 6 Out of band blocking performance dBm -10 0 dBm -38 -36 dBm -72 Single input impedance Fin = 2.4 GHz -52 -8 PinRF = -10 dBm, 30 MHz < FCWI < 2 GHz, BER < 0.001 -10 PinRF = -27 dBm, 2000 MHz < FCWI < 2399 MHz, BER < 0.001 -27 PinRF =-27 dBm, 2498 MHz < FCWI < 3000 MHz, BER < 0.001 -27 PinRF =-0 dBm, 3000 MHz < FCWI < 12.75 GHz, BER < 0.001 -10 dBm 32 Return Loss Return loss (3) (5) (3) UNIT dB dBm Typical operating conditions are at 2.85V operating voltage and 25C ambient temperature. The receiver sensitivity is measured at the device interface. The f0 = -64 dBm Bluetooth modulated signal, f1 = -39dbm sine wave, f2 = -39 dBm Bluetooth modulated signal, f0 = 2f1 - f2, and |f2 - f1| = n x 1MHz, where n is 3, 4, or 5. For the typical case, n = 3. Reference Table 2 Reference Table 3 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 TRANSMITTER PERFORMANCE CHARACTERISTICS MIN TYP (1) MAX UNIT 2.402 GHz -3 +1 +3 dBm 2.441 GHz -3 +1 +3 dBm 2.480 GHz -3 +1 +3 dBm PARAMETER POUTRF (2) CONDITION Transmit output power Power Density (3) Power density MOD F1AVG MOD F2MAX (4) F2AVG/F1AVG Modulation characteristics -4 1 2 dBm Data = 00001111 140 165 175 kHz Data = 10101010 115 125 (5) 0.8 20 dB Bandwidth ACP (3) Adjacent channel power (In-band spurious) 1000 kHz |M-N|=2 -48 -20 dBm |M-N|3 -51 POUT2xfo (6) PA 2nd Harmonic suppression Maximum gain setting: f0 = 2402 MHz, Pout = 4804 MHz POUT3xfo (3) PA 3rd Harmonic suppression Maximum gain setting: f0 = 2402 MHz, Pout = 7206 MHz ZRFOUT (7) RF Output/Input Impedance of RF Port (RF_inout) Pout at 2.4 GHz Return Loss (1) (2) (3) (4) (5) (6) (7) (8) (3) (8) kHz -40 dBm -30 dBm -30 dBm 47 Return Loss -14 dB Typical operating conditions are at VCC = 2.75V. The output power is measure at the device interface. Not tested in production. F2max > 115 kHz for at least 99.9% of all F2max. Modulation index set between 0.28 and 0.35. Out-of-Band spurs only exist at 2nd and 3rd harmonics of the CW frequency for each channel. Reference Table 1. Reference Table 4. SYNTHESIZER PERFORMANCE CHARACTERISTICS PARAMETER CONDITION MIN TYP MAX VCO Frequency range tLOCK Lock time f0 50 kHz f0offset (1) (2) Initial carrier frequency tolerance During preamble -75 0 75 kHz f0drift (1) (2) Initial carrier frequency drift DH1 data packet -25 0 25 kHz DH3 data packet -40 0 40 kHz DH5 data packet -40 0 40 kHz Drift Rate -20 0 20 kHz/50s tD -Tx (1) (2) Transmitter delay time 5000 UNIT fVCO From Tx data to antenna MHz 120 4 s s Frequency accuracy is dependent on crystal oscillator chosen. The crystal must have a cumulative accuracy of < 20ppm to meet Bluetooth specifications. Not tested in production. CRYSTAL REQUIREMENTS The LMX5252 contains a crystal driver circuit. This circuit operates with an external crystal and capacitors to form an oscillator. Figure 1 shows the recommended crystal circuit. Figure 3 specifies system clock requirements. The RF local oscillator and internal digital clocks for the LMX5252 is derived from the reference clock at the CLK+ input. This reference may either come from an external clock or a dedicated crystal oscillator. The crystal oscillator connections require an Xtal and two grounded capacitors.Y Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 7 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com It is also important to consider board and design dependant capacitance in tuning crystal circuit. Equations that follow allow a close approximation of crystal tuning capacitance required, but actual values on board will vary with capacitive properties of the board. As a result, there is some fine tuning of crystal circuit that has to be done that can not be calculated, must be tuned by testing different values of load capacitance. Many different crystals can be used with the LMX5252. Key requirements from Bluetooth specification is 20ppm. Additionally, ESR (Equivalent Series Resistance) must be carefully considered. LMX5252 can support maximum of 230 ESR, but it is recommended to stay <100 ESR for best performance over voltage and temperature. See Figure 2 for ESR as part of crystal circuit for more information. ESR of the crystal also has impact on the startup time of the crystal oscillator circuit of the LMX5252. TRANSMIT MODE STATE MACHINE, for system start up timing and Table 7. CRYSTAL The crystal appears inductive near its resonant frequency. It forms a resonant circuit with its load capacitors. The resonant frequency may be trimmed with the crystal load capacitance. Load Capacitance For resonance at the correct frequency, the crystal should be loaded with its specified load capacitance, which is the value of capacitance used in conjunction with the crystal unit. Load capacitance is a parameter specified by the crystal, typically expressed in pF. The crystal circuit shown in Figure 2 is composed of: * C1 (motional capacitance * R1 (motional resistance) * L1 (motional inductance) * C0 (static or shunt capacitance) The LMX5252 provides some of the load with internal capacitors Cint. The remainder must come from the external capacitors and tuning capacitors labeled Ct1 and Ct2 as shown in Figure 1. Ct1 and Ct2 should have the same the value for best noise performance. The LMX5252 has XOCTUNE which can be changed in register 2. There are 7 bits of tuning for XOCTUNE. Default value of 0028h, which results in an additional 2.6pF internal capacitance. This register can be used in production testing for additional tuning, if necessary. (See Table 4 for range of XOCTUNE). Crystal load capacitance (CL) is calculated as the following: CL = Cint + XOCTUNE + Ct1//Ct2T The CL above does not include the crystal internal self-capacitance C0 as shown in Figure 2, so the total capacitance is: Ctotal = CL + C0 Based on crystal spec and equation: CL = Cint + XOCTUNE + Ct1//Ct2m CL = 8pF + 2.6pF + 6pF = 16.6pF 16.6pF is very close to the TEW crystal requirement of 16pF load capacitance. With the internal shunt capacitance Ctotal: Ctotal = 16.6pF + 5pF = 21.6pF 8 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 LMX5252 CLK+ CLK- Cint XOCTUNE Ct1 Ct2 Crystal Figure 1. LMX5252 Crystal Recommended Circuit* R1 C1 L1 C0 Figure 2. Crystal Equivalent Circuit Crystal Pullability Pullability is another important parameter for a crystal, which is the change in frequency of a crystal with units of ppm/pF, either from the natural resonant frequency to a load resonant frequency, or from one load resonant frequency to another. The frequency can be pulled in a parallel resonant circuit by changing the value of load capacitance. A decrease in load capacitance causes an increase in frequency, and an increase in load capacitance causes a decrease in frequency. Frequency Tuning Frequency Tuning is achieved by adjusting the crystal load capacitance with external capacitors. It is a Bluetooth requirement that the frequency is always within 20 ppm. Crystal/oscillator must have cumulative accuracy specifications of 15 ppm to provide margin for frequency drift with aging and temperature. TEW Crystal The LMX5252 has been tested with the TEW TAS-4025A crystal, reference Table 1 for specification. Since the internal capacitance of the crystal circuit is 8 pF and the load capacitance is 16 pF, 12 pF is a good starting point for both Ct1 and Ct2. The 2480 MHz RF frequency offset is then tested. Figure 3 shows the RF frequency offset test results. Figure 3 shows the results are -20 kHz off the center frequency, which is -1 ppm. The pullability of the crystal is 2 ppm/pF, so the load capacitance must be decreased by about 1.0 pF. By changing Ct1 or Ct2 to 10 pF, the total load capacitance is decreased by 1.0 pF. Figure 4 shows the frequency offset test resuts. The frequency offset is now zero with Ct1 = 10 pF, Ct2 = 10 pF. Reference Table 2 for crystal tuning values used on Phoenix Development Board with TEW crystal. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 9 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Table 1. TEW TAS-4025A SPECIFICATION VALUE Package 4.0x2.5x0.65 mm - 4 pads Frequency 13.000 MHz Mode Fundamental Stability > 15ppm at -40 to +85C CL Load Capacitance 16pF ESR 80 max. C0 Shunt Capacitance 5pF Drive Level 50 10uV Pullability 2 ppm/pF min Storage Temperature -40 to +85C Table 2. TEW on Tucson Board REFERENCE LMX5252 Ct1 10pF Ct2 10pF Figure 3. Frequency Offset with 12pF //12 pF Capacitors 10 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 Figure 4. Frequency Offset with 10 pF//10 pF Capacitors Table 3. System Clock Requirements PARAMETER CREF External reference clock frequency CTOL Frequency tolerance (over full operating temperature and aging) XOCTUNE Digital crystal tuning load range COSC Crystal oscillator CESR Crystal serial resistance CREF-PS External reference clock power swing, pk to pk Cint Internal load capacitance CAGE Aging MIN TYP MAX UNIT 10 13 20 MHz -20 15 +20 ppm 20 MHz 8 10 13 100 200 pF 230 400 mV 1 ppm/year 8 pF Table 4. Register 2: XOCTUNE Tuning Load Range (1) BINARY VALUE HEX VALUE VALUE UNIT 000 0000 0 0 pF 010 1000 28 (1) 2.6 pF 111 1111 7F 8 pF Default value for RF initialization register 2. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 11 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Figure 5. ESR vs Load Capacitance for the Crystal 12 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Figure 6. Modulation and Eye Diagram Figure 7. Transmit Spectrum Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 13 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Figure 8. TX Impedance Characteristics 14 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Figure 9. RX Impedance Characteristics Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 15 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Figure 10. Transmitter Return Loss 16 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 FUNCTIONAL DESCRIPTION The circuitry of the LMX5252 (see FUNCTIONAL BLOCK DIAGRAM) utilizes a heterodyne receiver architecture with a low intermediate frequency (2 MHz) such that the intermediate frequency filters can be integrated on chip. The receiver consists of a low-noise amplifier (LNA) followed by two mixers. The intermediate frequency signal processing blocks consist of a poly-phase bandpass filter (BPF), two hard-limiters (LIM), a frequency discriminator (DET), and a post-detection filter (PDF). The received signal level is detected by a received signal strength indicator (RSSI). The received frequency equals the local oscillator frequency (fLO) plus the intermediate frequency (fIF): fRF = fLO + fIF (supradyne). The LMX5252 is able to operate with multiple reference frequencies between 10 and 20 MHz. Simulations to ensure performance are done with 13.0 MHz, 26.0 MHz (used by GSM and WCDMA platforms in Europe), and 19.2 MHz. To operate with multiple reference frequencies, the LMX5252 contains a fractional-N delta-sigma synthesizer. The synthesizer consists of a phase detector, a charge pump, an (off-chip) loop-filter, an RFfrequency divider, and a voltage controlled oscillator (VCO). The transmitter utilizes IQ-modulation with bit-stream data that is gaussian filtered. Other blocks included in the transmitter are a VCO buffer and a power amplifier (PA). SYSTEM INTERACTION For complete operation, the LMX5252 must be connected with a Bluetooth baseband controller (e.g., LMX5100) or to a device that can emulate the baseband functionality. The baseband function is to read and write to the internal registers in the radio chip. These registers are used for setting the frequency, tuning, and control. The communication between the baseband controller and the radio chip is performed via the serial interface. The LMX5252 also requires an external antenna. The antenna must be connected through a 50 ohm interface. The power supply is divided externally into four parts: two for the RF blocks (RF and VCO), one for the IF blocks, and one for the low frequency and digital blocks. Each of the supplies must be low frequency decoupled for maximum performance. RECEIVER FRONT-END The receiver front-end consists of a low-noise amplifier (LNA) followed by two mixers and two low-pass filters for the I- and Q-channels. The intermediate frequency (IF) part of the receiver front end consists of two IF amplifiers that receive input signals from the mixers, delivering balanced I- and Q-signals to the poly-phase bandpass filter. The poly-phase bandpass filter is directly followed by two hard-limiters that together generate an AD-converted RSSI signal. Poly-Phase Bandpass Filter The purpose of the IF bandpass filter is to reject noise and spurious (mainly adjacent channel) interference that would otherwise enter the hard limiting stage. In addition, it takes care of the image rejection. The bandpass filter uses both the I- and Q-signals from the mixers. The out-of-band suppression should be higher than 40 dB (f<1 MHz, F>3 MHz). The bandpass filter is tuned over process spread and temperature variations by the autotuner circuitry. A 5th order Butterworth filter is used Hard-Limiter and RSSI The I- and Q-outputs of the bandpass filter are each followed by a hard-limiter. The hard-limiter has its own reference current. The RSSI (Received Signal Strength Indicator) measures the level of the RF input signal. The RSSI is generated by piece-wise linear approximation of the level of the RF signal. The RSSI has a mV/dB scale, and an analog-to-digital converter for processing by the baseband circuit. The input RF power is converted to a 5- bit value. The RSSI value is then proportional to the input power (in dBm). The digital output from the ADC is sampled on the BPKTCTL signal low-to-high transition. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 17 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com RECEIVER BACK-END The hard-limiters are followed by a two frequency discriminators. The I-frequency discriminator uses the 90x phase shifted signal from the Q-path, while the Q-discriminator uses the 90x phase-shifted signal from the I-path. A polyphase bandpass filter performs the required phase shifting. The output signals of the I- and Q-discriminator are substracted and filtered by a low-pass filter. An equalizer is added to improve the eye-pattern for 101010 patterns. After equalization, a dynamic AFC (automatic frequency offset compensation) circuit and slicer extract the RX_DATA from the analog data pattern. It is expected that the Eb/No of the demodulator is approximately 17 dB. Frequency Discriminator The frequency discriminator gets its input signals from the limiter. A defined signal level (independent of the power supply voltage) is needed to obtain the input signal. Both inputs of the frequency discriminator have limiting circuits to optimize performance. The bandpass filter in the frequency discriminator is tuned by the autotuning circuitry. Post-Detection Filter and Equalizers The output signals of the FM discriminator first go through a post-detection filter and then through an equalizer. Both the post-detection filter and equalizer are tuned to the proper frequency by the autotuning circuitry. The post-detection filter is a low-pass filter intended to suppress all remaining spurious signals, such as the second harmonic (4 MHz) from the FM detector and noise generated after the limiter. The post-detection filter also helps for attenuating the first adjacent channel signal. The equalizer improves the eye opening for 101010 patterns. The post-detection filter is a third order Butterworth filter. AUTOTUNING CIRCUITRY The autotuning circuitry is used for tuning the bandpass filter, the detector, the post-detection filter, the equalizer, and the transmit filters for process and temperature variations. The circuit also includes an offset compensation for the FM detector. SYNTHESIZER The LMX5252 features a fractional-N delta-sigma (DS) synthesizer that operates using an external reference frequency in the range of 10 to 20 MHz or, alternatively, up to 40 MHz. The synthesizer consists of a phase-frequency detector, a charge pump, a low-pass loop filter, a programmable frequency divider, a voltage-controlled oscillator (VCO), a delta-sigma modulator, and a lookup table. The frequency divider consists of a divide-by-2 circuit (divides the 5 GHz signal from the VCO down to 2.5 GHz), a divide-by-8-or-9 divider, and a digital modulus control. The delta-sigma modulator controls the division ratio and also generates an input channel value to the lookup table. Phase-Frequency Detector The phase-frequency detector is a 5-state phase-detector. It responds only to transitions, hence phase-error is independent of input waveform duty cycle or amplitude variations. Loop lockup occurs when all the negative transitions on the inputs, F_REF and F_MOD, coincide. Both outputs (i.e., Up and Down) then remain high. This is equal to the zero error mode. The phase-frequency detector input frequency range is between 10 and 20 MHz. The phase-frequency detector has the option of being turned off such that the PLL can be opened. The enabling/disabling of the phase detector operation is performed by the control signal PHD_ON. This mode is not actively used in the LMX5252. TRANSMITTER CIRCUITRY The transmitter consists of ROM tables, two Digital to Analog (DA) converters, two low-pass filters, IQ mixers, and a power amplifier (PA). The ROM tables generate a digital IQ signal based on the transmit data. The output of the ROM tables is inserted into IQ-DA converters and filtered through two low-pass filters. The two signal components are mixed up to 2.5 GHz by the TX mixers and added together before being inserted into the transmit PA. 18 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 IQ-DA Converters and TX Mixers The ROM output signals drive an I- and a Q-DA converter. Two Butterworth low-pass filters filter the DA output signals. The 6 MHz clock for the DA converters and the logic circuitry around the ROM tables are derived from the autotuner. The TX mixers mix the balanced I- and Q-signals up to 2.4- 2.5 GHz. The output signals of the I- and Q-mixers are summed. LOW FREQUENCY CIRCUITRY The low frequency circuitry includes an adjustable crystal oscillator (XO), an adjustable low power oscillator (LPO), a power-on reset (POR) block, and an off-chip reset input. For generation of the system clock, a 10-20 MHz crystal or up to a 40 MHz external reference clock input can be used. For operation in low power modes, the low frequency circuitry generates a 3.2 kHz clock, synthesized from a 32.768 kHz or 32.0 kHz signal. The source can be either a reference clock or crystal signal input. Alternatively, the main system clock can be used. DIGITAL CIRCUITRY The digital functions of the LMX5252 provide I- and Q-signal generation in the transmitter, baseband interface control, filter tuning, fractional XO and PLL frequency division, and power-up control for all analog blocks. The digital circuitry also allows for programming of the analog blocks in order to compensate for process variations. By using an external voltage reference, the serial interface automatically adjusts the logic voltage levels to different baseband controllers. The logic is contained in the Control Logic and Serial Interface and the IQROM blocks. Scan testing is used for all logic. CRYSTAL OSCILLATOR The oscillator should be as accurate as possible. If the LMX5252 is used in an application that already uses an XTAL oscillator, the oscillator circuitry will act as buffer to an AC coupled via 10 pF to a small signal (100 to 400 mVp). Alternatively, via a 20 k resistor in series with 10 pF for an externally applied CMOS (square-wave) signal into pin XO_P. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 19 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com APPLICATION INFORMATION Figure 11. Base Band RF Interface BDATA_1: Transmit/receive Bluetooth data and sync signal for transmit interface to RFDATA. The RFDATA signal is the multiplexed Bluetooth data receive and transmit signal. The data is provided at a bit rate of 1 Mbit/s with 12x oversampling, synchronized to the 12 MHz BBCLK. The RFDATA signal is a dedicated RF interface pin. This signal is driven to a logic high after reset. BPKTCTL: Access code indication from baseband controller. In transmit mode this controls the transmitter state, high = TX ON. In receive mode this controls the filter bandwidth, high = narrow, low = wide interface to BTSEQ, signals indicate internal states of the Bluetooth sequencer, which are used for interfacing to some external devices. BXTLEN: BRCLK enable. System clock enable signal (active high) interface to RFCE. The RFCE signal is the chip enable to the radio chip. When RFCE is high, RF chip power is controlled by its power control registers. When RFCE is low, the RF chip is powered-down. However, the serial interface is operational and the CP3000 device can access the RF chip internal registers. The RFCE signal is an alternate function of a general-purpose I/O pin. At reset, this pin is in TRI-STATE mode. Software must enable the alternate function of the pin to give control over this signal to the RF interface. During Bluetooth power-down phases, the CP3000 device provides a mechanism to reduce the power consumption of an external RF chip by driving the RFCE signal of the RF interface to a logic low level. This feature is available when the Power Management Module of the CP3000 device has enabled the Hardware Clock Control mechanism. BPOR: Reset signal to baseband controller interface to RESET, Chip general reset with internal pull-down. NC for normal operation. RESET#: External reset (active low) to RF chip from baseband controller 20 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 BRCLK: Buffered system clock output. Pin36 = high then same as crystal. Pin 36 = low then divide by 2 output, interface to the X1CKI/BBCLK, is the input signal for the 12- MHz clock signal. The radio chip uses this signal internally as the 12x oversampling clock and provides it externally to the CP3000 device for use as the Main Clock. Some CP3000 devices have a separate CLKIN pin for receiving an external clock. BDDATA; I/O DBUS data interface to SDAT. The SDAT signal is multiplexed serial receive and transmit data between the radio chip and the CP3000 device. The SDAT signal is an alternate function of a general-purpose I/O pin. At reset, this pin is in TRI-STATE mode. Software must enable the alternate function of the pin to give control over this signal to the RF interface. BDCLK: DBUS clock. Maximum 4 MHz interfaces to SCLK. The SCLK signal is the serial interface shift clock output. The CP3000 device always acts as the master of the serial interface and therefore always provides the shift clock. The SCLK signal is an alternate function of a general-purpose I/O pin. At reset, this pin is in TRISTATE mode. Software must enable the alternate function of the pin to give control over this signal to the RF interface. BDEN#: DBUS enable (active low). Latch enable, data latched from low to High, interface to SLE. The SLE pin is the serial load enable output of the serial interface of the CP3000 device. During write operations (to the radio chip registers), the data received by the shift register of the radio chip is copied into the address register on the next rising edge of SCLK after the SLE signal goes high. During read operations (read from the registers), the radio chip releases the SDAT line on the next rising edge of SCLK after the SLE signal goes high. At reset, this pin is in TRI-STATE mode. Software must enable the alternate function of the pin to give control over this signal to the RF interface. PROGRAMMING DESCRIPTION RADIO-BASEBAND INTERFACE The radio-baseband (RF-BB) interface is comprised of eight signal pins according to the BlueRF specification. However, in the LMX5252, two additional pins are present. These pins are BPOR and B3k2. BPOR is used for power-on reset of the baseband. B3k2 is a clock output from the radio supplying a 3.2 kHz reference clock to the baseband for low power mode operation. SERIAL INTERFACE TIMING Table 5. Serial Interface Timing PARAMETER tCS Data to clock setup time tCH tCWH CONDITION MIN TYP MAX UNIT 10 ns Data to clock hold time 1 ns Clock pulse width high 20 ns tCWL Clock pulse width low 20 ns tES Clock to enable setup time 5 ns tCES Enable to clock setup time 5 ns tEWH Enable pulse width high 200 ns tEWL Enable pulse width low 2500 ns See Figure 4 Figure 12. Serial Port Write Timing Diagram Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 21 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com ACCESSING THE REGISTERS The registers in the radio are accessed over the DBUS (see Table 2). Table 6. Radio Registers FIELD NO. OF BITS COMMENT Device Address 3 Radio is allocated binary device address 101. Read/Write 1 Driving this bit high indicates a read operation. Register Address 5 Data 16 When accessing a 32-bit register the user must write to the same register twice. The highest bits ([31:16]) are accessed first and on the second write, the lowest bits ([15:0]) are accessed. The time in-between these two accesses must be at least two clock cycles. In the case of a 4 MHz clock, the minimum time would be 500 ns. 16-Bit Register When reading a 16-bit register, the value of the register is read back. If a value of 0x0063 is written, 0x0063 is read back. 32-Bit Register The value read from a 32-bit register is not the actual register value, but a counter value. The value that the user receives when reading a 32-bit register depends on read/ write order. If the highest bits are written first, 0x0000 is read back. If the lowest bits are written first, 0x0001 is read back. If the user writes two consecutive times to the register, 0x0001 is always read back. The read back of a 32-bit WORD is independent of data written to the register. Example 1 Writing 0xFFFF DC04 to register 10. BDDATA 101 0 01010 1111111111111111 BDDATA 101 0 01010 1101110000000100 Reading register 10. BDDATA 101 1 01010 and following value is received: 0000000000000001 Example 2 Writing 0xFFFF DC04 to register 10 when doing read back between the writing. BDDATA 101 0 01010 1111111111111111 BDDATA 101 1 01010 and following value is received: 0000000000000000 BDDATA 101 0 01010 1101110000000100 BDDATA 101 1 01010 and following value is received: 00000000000000011 The order for accessing the registers is from high to low: 17, 15, 14, 12, 11, 10, 9, 8, 7, 6, 5, 4, 2, and 1. These registers need to be written to during the initialization of the radio. After initialization the radio is ready to transmit or receive. The radio receives and transmits on the positive edge of the BDCLK. Figure 13 and Figure 14 show the timing for register writing and reading. 22 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 Figure 13. 32-Bit Register Write Timing Figure 14. 32-Bit Register Read Timing POWER-UP MODE, STATE MACHINE When the LMX5252 is powered up, it enters a power-up mode and the power-up sequence is started. After that, the LMX5252 performs a controlled reset of the baseband (see Figure 15 and Figure 16). The LMX5252 states are described in the following paragraphs. Off: When the LMX5252 enters Off mode, all configuration data is lost. In this state, the LMX5252 also drives BPOR low. Power-up: When the power supply is on and the RESET# is high, the LMX5252 starts up the crystal oscillator and enters Power-up mode. After the crystal oscillator (XO) is settled, the LMX5252 sends four clock cycles on the BRCLK before driving BPOR high. RF init: The baseband now drives BXTLEN high and takes control of the XO. The baseband performs all the needed initialization (i.e., writing the registers in the radio, such as XO trim). Idle: The baseband drives BDATA_1 low when the initialization is ready. The LMX5252 is now ready to start transmitting, receiving, or to enter Sleep mode. Sleep: The LMX5252 can be forced into Sleep mode at any time by driving BXTLEN low. All configuration settings are kept, only the Bluetooth low power clock is running (B3k2). Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 23 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Wait XTL: When BXTLEN goes high, the crystal oscillator becomes operational. When it is stable, the LMX5252 enters Idle mode and outputs the BRCLK for the baseband. From any state RESET# = 0 or Power supply is switched on/off Off RESET# = 1 Power supply on Wait for XTL XO to settle From any state after RF init BXTLEN = 0 Power-up BXTLEN = 1 %'$7$B 'RQW FDUH Write registers Sleep XTL XO settled Wait for XTL XO to settle RF init BXTLEN = 1 Wait XTL XTL XO settled Idle Figure 15. Power-Up Sequence TRANSMIT MODE STATE MACHINE LMX5252 Radio can only initiate a transmit sequence from the idle state mode, see Figure 16. Idle: To initiate the transmit mode, the baseband needs to write a new channel number to the radio. This write command enables the PLL counter. (The counter value is set in register 1 bit(7:0) Wait data: The PLL counter starts to count down and when it reaches zero the PLL is enabled. LMX5252 then waits for the TX clock synchronization on BDATA_1. Data: Synchronization is done; LMX5252 is in this state until BPKTCTL goes high. TX power up: When the BPKTCTL is high the complete transmit path is powered up. Now LMX5252 is transmitting a carrier and is waiting for TX data on BDATA_1. TX data: The transmit path is powered down by BPKTCTL going low. Note that the synthesizer is still active. The synthesizer is active during the complete transmit sequence until LMX5252 is in idle state. 24 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 Start up and initiation of the radio RESET# BDATA_1 BXTLEN BRCLK (13 MHz) BPOR B3k2 (3.2 kHz) BDEN# BDCLK (4 MHz) BDDATA Figure 16. Power-up Timing Diagram Table 7. Start Up Timing PARAMETER TIME COMMENT t1 20 ms Start up time for the crystal. t2 350 ns for 13 MHz clock BPOR to the baseband will go high after 4.5 clock cycles. t3 Depends of the baseband when it is ready to set BXTLEN high after receiving BPOR from the radio. t4 Depends of the baseband how long time after BXTLEN goes high it is ready to set BnDEN low. t5 Is set by the baseband; the radio is not dependent on it at all. t6 6.25 s t7 Minimum 500 ns 26 (4 MHz) clock cycles are needed to access/doing register writing. At least 2 clock cycles are needed in between accessing two registers. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 25 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com BDATA_1=1 Figure 17. Tx-Mode Sequence RESET# BDEN# BDATA_1 Figure 18. Tx-Mode Timing Diagram 26 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com PARAMETER SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 TIME MEASURED TIME t1 t2 The radio is ready for transmit mode as soon as the frequency is written. After that LMX5252 is just waiting for the synchronization pulse. 1 s t3 t4 COMMENT Need to optimized 1 s Synchronization pulse 0.3 s. 109 s Is set by the baseband. 86 s Time between BPKTCTL goes high and data is available on BDATA1. TX is turned on when BPKTCTL goes high, the PA is turned on x s after that. x is set by register 17, (bit 15:8). t5 Need to optimized Time between no data on BDATA_1 and BPKTCTL goes low. The Pa is turned off when BPKTCTL goes low the rest of the TX path turns off x s after the PA. x is set by register 17, (bit 7:0). RECEIVE MODE STATE MACHINE LMX5252 Radio can only initiate a receive sequence from the idle state, see Figure 19. Idle: To enter receive mode the baseband needs to write a new channel number to the radio. This write command enables the PLL counter. This counter is set in register 1 and sets the settling time for the receive path. RX PLL: The PLL starts and the counter begins counting down (1is/bit) when BnDEN goes high. RX Wide Filt: When the counter reaches the value 0 the receive path is powered up and begins detecting the incoming data using the wide tracking filter. RX Narrow Filt: Upon detection of the access code, the baseband drives the BPKTCTL high and the radio switches to the narrow tracking filter. After receiving the last data-bit, the baseband ends the receive sequence and puts the radio back to Idle state. Both the RX path and the PLL are powered down. LMX5252 now releases BDATA_1 to be used by the baseband. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 27 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Figure 19. Rx-Mode Sequence 28 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 RESET# BDEN# BDATA_1 Figure 20. Rx-Mode Timing Diagram PARAMETER TIME MEASURED TIME t1 120 s 120 s COMMENT Time between when BnDEN goes high and when the radio puts data on BDATA1. Depends on when the baseband has detected the access code. The LMX5252 requires that BPKTCTL goes high for at least 1 is after BDATA_1 is done to switch off RX path. t2 t3 Time between register writing for switching off RX path and set new node and channel. This register writing will be implemented and used for LMX5252. 11.2 s REGISTER MAPPING Table 8 specifies the different registers in the LMX5252 Read or Write status, the address and value at powerup, and programmed value. Some of the trim registers have specific values and are indicated by a note in the table. Values programmed after startup are 12MHz clock source. Table 8. Register Setup (1) Register Address (Decimal) 0 (1) (2) (3) Register Name Width (Bits) R/Wb Power-Up Value (Hex) Program Value (Hex) Program Value (Binary) (2) 16 W, R 0005 N/A N/A RF Channel (3) 1 SyntRxOnCounter 16 W, R FFFF 5A00 0101 1010 0000 0000 2 XO Trim 16 W, R 0000 0028 0000 0000 0010 1000 3 RSSI 16 R Undefined NA NA Two words needs to be written consecutive to the same address. Register 0 must be updated every frame. Register 1, 2, 4-12, 14, 15, and 17 must be updated after power-up. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 29 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Table 8. Register Setup(1) (continued) Register Address (Decimal) Width (Bits) R/Wb 32 (1) (3) (4) 4 Trim 5 Control 6 BlockOn (1) (3) 7 Enable (3) 8 Power Control (3) (5) (3) (1) (3) Power-Up Value (Hex) Program Value (Hex) Program Value (Binary) W, Wc 0037 0000 003C D400 0000 0000 0011 1100 1101 0100 0000 0000 16 W, R 0050 4844 0100 1000 0100 0100 32 W, Wc 0000 0040 0080 0060 0000 0000 1000 0000 0000 0000 0110 000 16 W, R 0007 001F 0000 0000 0001 1111 16 W, R 001F 0016 0000 0000 0001 0110 32 W, R, Wc 0013 D620 0012 4F80 0000 0000 0001 0010 0100 1111 1000 0000 32 W, Wc FFFF DC04 FFFF F801 1111 1111 1111 1111 1111 1000 0000 0001 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 9 Frequency Reference 10 Clock Division (1) 11 DSMIN (1) 32 W, Wc 12 DSMOUT 32 W, R 0000 0000 0000 0000 0000 0000 13 Test pins (4) 16 W, R FFFF FFFF 1111 1111 1111 1111 32 W, Wc 0092 8EC3 00A0 8EC3 0000 0000 1010 0000 1000 1110 1100 0011 32 W, Wc 004A 0000 0150 A100 0000 0001 0100 1010 1110 1101 0000 0000 16 W, R 0000 0000 0000 0000 0000 0000 (6) 14 LPO Division 15 Auxiliary (7) (8) 16 MidTiming (3) (6) (1) (3) (9) (8) 17 PA Counter 16 W, R FFFF 0108 0000 0001 0000 1000 18 WrOffMode 16 W xxxx xxxx xxxx 30 ManufacturerCode1 16 R E3C7 N/A N/A 16 R 6000 N/A N/A 31 (4) (5) (6) (7) (8) (9) (10) Register Name ManufacturerCode2 (10) Register 13 is only for test and does not need to be updated after power-up. In conjunction with CP3000 rev B0, B1 Clock Division Ratio set for 12MHz Two words needs to be written consecutive to the same address. Register 1, 2, 4-12, 14, 15, and 17 must be updated after power-up. Register 13 is only for test and does not need to be updated after power-up. Clock Division Ratio set for 12MHz Table 9. Selected Register Description REGISTER REGISTER NAME BIT DESCRIPTION 2 XO TRIM 6:0 Trim value for the internal capacitor load of the crystal 3 RSSI 4:0 The RSSI is read when RSSI register is accessed 4 TRIM- VCO Cal 23 VCO calibration bit 22:20 19:16 15:12 11:8 7:0 VCO frequency range trim value Current source trim value for both PA and charge pump Current source trim value for both V to I and the mixer driver The 4 bit signal controls the expectation value Spare bits Power Control 4 Gain Step Power Control 3:0 Internal PA current timing TRIM- VCO trim TRIM- CS trim TRIM- Tx bias TRIM- RGTRIMLO TRIM- RGTRIMLO 8 30 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 APPLICATION DIAGRAM AND SCHEMATICS Figure 21. Application Diagram Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 31 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Table 10. Component Bill of Material for 12 MHz REFERENCE DESCRIPTION VALUE TOLERANCE SIZE C1, C2, C3, C8. C9. C10 Ceramic Capacitor 4.7 pF 20% 402 C5 Ceramic Capacitor 39 pF 20% 402 C6 Ceramic Capacitor 220 pF 10% 402 C7 Ceramic Capacitor 2200 pF 10% 402 C11 Ceramic Capacitor 2.2 uF 20% 603 C12 Ceramic Capacitor 0.1 uF 20% 603 C13 Ceramic Capacitor 12 pF 10% 402 C14 Ceramic Capacitor 15 pF 10% 402 R1 Resistor 10 k 5% 402 Crystal 12MHz R2 Resistor 3.3 k 5% 402 R3 Resistor NM 0 402 Table 11. Component Bill of Material for 13 MHz REFERENCE DESCRIPTION VALUE TOLERANCE SIZE C1, C2, C3, C8. C9. C10 Ceramic Capacitor 4.7 pF 20% 0402 C5 Ceramic Capacitor 39 pF 20% 0402 C6 Ceramic Capacitor 220 pF 10% 0402 C7 Ceramic Capacitor 3300 pF 10% 0402 C11 Ceramic Capacitor 2.2 uF 20% 0603 C12 Ceramic Capacitor 0.1 uF 20% 0603 C13 Ceramic Capacitor 12 pF 10% 0402 C14 Ceramic Capacitor 15 pF 10% 0402 R1 Resistor 10 k 5% 0402 Crystal 13MHz R2 Resistor 3.3 k 5% 0402 R3 Resistor NM 0 32 Submit Documentation Feedback 0402 Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 Figure 22. Reference Schematic with CP3BT26 Base Band Figure 23. Tucson Reference Schematic Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 33 LMX5252 SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Figure 24. Tucson Reference Layout 34 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 LMX5252 www.ti.com SNOSCW4A - DECEMBER 2004 - REVISED APRIL 2013 REVISION HISTORY Changes from Original (December 2004) to Revision A Page * Added all the revision histories that were at the end of this data sheet. ............................................................................ 34 * Added 0.1 (April 2003) First draft of advance datasheet. ................................................................................................... 34 * Added 0.2 (June 2003) This update includes modifications to electrical specs, minor corrections, and the addition of the Physical Dimensions section. ....................................................................................................................................... 34 * Added 0.3 (July 2003) Update of physical dimensions. Changed document status from Advance Information to Preliminary. ......................................................................................................................................................................... 34 * Added 0.4 (August 2003) Updates in Tables 2, 4, 5, and 6. New subsections added to Functional Description. Addition of Programming Description section. .................................................................................................................... 34 * Added 0.5 (March 2004) Updates to Application diagram, Register description, Pin description, Crystal specifications and Operating conditions ............................................................................................................................. 34 * Added 0.7 (May 2004) Updates to Applications Diagram, BOM, Selected register description, Register values, Electrical Specifications, and Pin descriptions .................................................................................................................... 34 * Added 0.8 (July - Sept 2004) Addition of reference schematics, Base band RF interface description, typical performance characteristics and new information on crystal tuning Not released ............................................................. 34 * Added 1.0 (December 2004) See Table 21 on page 36 for edits to current revision. ........................................................ 34 * Changed to ordering information - Connections Diagram ................................................................................................. 34 * Changed B3K2 default to ground - Pin Description ........................................................................................................... 34 * Changed to Tx/Rx impedance, synthesizer lock time, output power, 2nd & 3rd Harmonics, lead soldering temperature, humidity of operation, absolute maximum input power - Electrical Specifications ....................................... 34 * Added Tx/Rx impedance plots - Typical Performance Characteristics .............................................................................. 34 * Added to reg 15 - Register Map ......................................................................................................................................... 34 * Added Update to loop filter values and new schematic and layout added - Application Diagram Schematics ................. 34 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links :LMX5252 35 PACKAGE OPTION ADDENDUM www.ti.com 8-Oct-2015 PACKAGING INFORMATION Orderable Device Status (1) LMX5252LQ/NOPB ACTIVE Package Type Package Pins Package Drawing Qty WQFN NJJ 36 250 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR Op Temp (C) Device Marking (4/5) -40 to 85 X5252LQ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 8-Oct-2015 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 21-Nov-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device LMX5252LQ/NOPB Package Package Pins Type Drawing WQFN NJJ 36 SPQ 250 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 178.0 16.4 Pack Materials-Page 1 6.3 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 6.3 1.5 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 21-Nov-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMX5252LQ/NOPB WQFN NJJ 36 250 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NJJ0036B LQA36B (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LMX5252LQ/NOPB LMX5252LQX/NOPB