EUROPEAN SELECTION 2000 / 2001 The publication of ALPS ELECTRIC EUROPA GmbH shows only a selection of the complete ALPS product line. Please note that the used order no. system is only valid for the European market. For more information on Alps complete line of electromechanical components and systems and according order instructions please refer to ALPS specific product catalogues or contact our sales representatives listed overleaf. The information in this guide has been carefully checked and is believed to be reliable, however, no responsibility can be assumed for inaccuracies that may not have been corrected. All information in this guide is subject to change without prior notice. Furthermore ALPS cannot assume responsibility for the use of any license under the patent rights of ALPS or any third parties. Content Power Switch 4 Push Switches 5 - 8 Slide Swichtes 9 - 10 Rotary Switches Tact Switches 11 12 - 26 Compact Stick Switch 27 Rotary Potentiometer 28 - 33 Slide Potentiometer 34 - 37 Hollow Shaft Rotary Encoder 38 Dual Shaft Encoder & Pop-Up Encoder 39 Rotary Encoder 40 - 42 9 mm Size Encoder 43 Hollow Shaft Encoder 44 Magnetic Encoder 45 Keytop Product Line 46 Power Switch 4 Order Number Model Terminal Type Travel STPSDKEA3 SDKEA3 Printed Terminals 2,5 mm STPSDKEA3 28.8 18.5 18.9 Latching 3.5 (Total travel) 3.3 P.C.Board mounting face 4.6 9.4 12 16.8 3.5 1.45 o3.2 11.8 8.5 1 1.2 3.3 4.4 26.2 1 2 Terminal No. 2/1 2 Terminal No. 1/1 2.5 Only for 1.6mm in P.C.Board thickness. 3.3 6.7 2.5 3.1 2.2 6.6 11.9 4.5 2.5 2.5 (Travel) Terminal No. 1/2 Unit: (mm) Termimal No. 2/2 Push Switches 5 Order Number Model Number of Poles STSPUN121 STSPUN141 STSPUN122 STSPUN142 STSPEC123 STSPEC124 SPUN19-2N-LB SPUN19-4N-LB SPUN19-2N-W SPUN19-4N-W SPEC12-2N-W2 SPEC12-2N-LB2 2 4 2 4 2 2 Number of Position Mode 2 Momentary 2 Momentary 2 Latching 2 Latching 2 Latching 2 Momentary Ratings: 0.1A 30V DC; straight terminals as standard SPUN19 Snap-In Terminals Optional SPEC12 Snap-In Terminals Optional A 1. Travel and Total Travel Travel 10 12 +0.2 -0.6 Total travel a 3.75 12.5 2. Detail of a T.T. T.T. 3.4 T T 2.5 4 2.5 mm travel Knob face 12.5 4 3.5 H2.5 2R 0. 5 H3.3 2.5 12.5 2 1 1 0.35 5 Terminal No.1 P.C.Board mounting face 0.6 2.5 2.5 2 (0.2) (1.8) 8.8 Unit: (mm) Push Switches 6 Order Number Model Number of Poles Ratings Mode Mounting Height (mm) Change Over Timing Life (Cycles) STSPUJ121 STSPUJ141 STSPUJ122 STSPUJ142 SPUJ19-2N-LB SPUJ19-4N-LB SPUJ19-2N-W SPUJ19-4N-W 2 4 2 4 0.1A 30V DC 0.1A 30V DC 0.1A 30V DC 0.1A 30V DC Momentary Momentary Latching Latching 5 mm 5 mm 5 mm 5 mm Non-shorting Non-shorting Non-shorting Non-shorting 10.000 10.000 10.000 10.000 SPUJ12 Series a H2.80.1 Total travel T 5 H2 R0 .5 SPUJ14 Series Unit: (mm) 1 1 5 15.2 Knob face 4-poles:22.7 7.2 8.8 Unit: (mm) 7 P2.5 0.6 A 7.4 (1.5) 2 9.8 Terminal No.1 (0.2) Travel T.T. 7.5 +0.1 -0.3 4 P.C.Board mounting face Push Switches 7 Order Number Model Number of Poles Number of Position Mode Terminal Type Change Over Timing STSPPH211 STSPPH111 STSPPH411 STSPPH412 SPPH21-W SPPH11-W SPPH41-W SPPH41-LB 2 2 2 2 2 2 2 2 Latching Latching Latching Momentary Straight Straight Straight Straight Non-shorting Non-shorting Non-shorting Non-shorting SPPH21 Series A 6 3.5 0.7 R0 .5 2.3 1.8 3.5 o0.9holes 6.5 2.5 12.5 6 1 2 (1.5) Total travel 2- 1.5 (0.2) 1.8 .5 2.50.1 1 2R0 Travel 6 2.50.1 2.5 3.5 2.5 0.5 0.35 2.5 2.5 3.5 Terminal No.1 6.5 SPPH11 Series A 10 7 Travel 2.5 2- 2.2 Total travel 2 0.4 8.5 9 5 .5 2.5 2.5 R0 1.5 (1.8) Terminal No.4 3.5 8.5 5 11 2 .5 (1.5) Total travel 17.5 R0 (0.2) 2- 3.3 Travel 10 7 4 2.5 10 1.5 4 3.30.1 13.5 A (0.2) 10 3.5 0.35 0.35 0.6 Terminal No.4 2.5 5 0.6 2.5 5 2.5 2.5 SPPH41 Series A 6.5 4 3.30.1 2.5 8.5 4 3.3 2.5 11 2 (9.5) (0.2) 0.3 Unit: (mm) o1 5.4 P.C.Board mounting surface 0.5 2.5 2.5 Terminal No.3 Terminal No.2 (common) 3 Location lug 3 2.5 Terminal No. 1 4 5 6 1 2 3 5.4 For location lug o1.2 +0.1 0 hole 6-o0.9 +0.1 0 hole 3.5 0.8 8.5 18 2.2(Travel) 3(Total travel) 2.5 Push Switches 8 Order Number Model Number of Poles Number of Position Mode Terminal Type Change Over Timing STSPPJ301 STSPPJ302 SPPJ3-EN2-PW SPPJ3-EN2-PLB 2 2 2 2 Latching Momentary Printed wiring Terminals Printed wiring Terminals Non-shorting Non-shorting SPPJ3 Series A (22) 120.3 Total travel 10 3.5 Travel (6.6) 2.8 0.6 0.6 2.5 2.5 3.5 8.3 b 3.5 4.7 2.5 P.C.Board mounting face Terminal No.6 Terminal for printed wiring P.C.Board mounting face R0 .3 3.5 t : 0.35 0.6 Unit: (mm) 0.35 2.5 4.2 Slide Switches Number of Poles Number of Positions Lever Height (mm) Change Over Timing Life (Cycles) Contact Resistance (m) Type SSSS212-01 SSSS213-01 SSSS222-01 SSSS223-01 SSSS212-11 SSSS213-11 SSSS222-11 SSSS223-11 Vertical Vertical Vertical Vertical Horizontal Horizontal Horizontal Horizontal 1 1 2 2 1 1 2 2 2 3 2 3 2 3 2 3 2 mm 2 mm 2 mm 2 mm 2 mm 2 mm 2 mm 2 mm Non-shorting Non-shorting Non-shorting Non-shorting Non-shorting Non-shorting Non-shorting Non-shorting 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 70 m 70 m 70 m 70 m 70 m 70 m 70 m 70 m Standard Standard Standard Standard Standard Standard Standard Standard Travel 8.5 3.5 2 3.5 1.5 1.5 2 3 C Terminal No. 1 0.3 0.5 2.5 2.5 2 3.5 P.C.Board mounting face 3.5 1.5 0.7 1-3 0. 0.7 3.7 Terminal No.1 Travel 13 a 2 b 2c 1.5 P.C.Board mounting face 1-2 2 2.5 SSSS2 Series Horizontal Type 3.5 STSSS2121 STSSS2131 STSSS2221 STSSS2231 STSSS2122 STSSS2132 STSSS2222 STSSS2232 Model Direction of Knob 0.5 Order Number 9 0.6 3.3 2 2 2 2 2.45 A 0.3 A Auto-dipping is not possible Operating force with detent : 21.5N{204153gf} b J a 2.51.5N{255153gf} Operating force with detent : a J b } 1.51N{153102gf} } c Jb bJc 2-2 2-3 Travel 1.5 9 2 Terminal No. 1 2.5 0.3 A 3.3 A 3.3 2 2 2 2 13 Terminal No. 1 0.6 2.5 2.5 8.5 2.5 3.5 0.3 0.6 P.C.Board mounting face 3 3.5 (6.5) 1.5 3.5 2 3.5 3 2 1.5 P.C.Board mounting face 1.5 2 2 a bc Travel Operating force with detent : a J b 1.51N{153102gf} c Jb } b Ja 2.51.5N{255153gf} b Jc } Operating force with detent : 1.51N{153102gf} SSSS2 Series Vertical Type 1-2 8.5 b Travel 2c 1.5 3.5 1.5 2 Travel 2 P.C.Board mounting face 3 (5.5) 3.5 Terminal No.1 3.5 2 5.5 C 1.5 2 0. 3.5 1.5 1-3 13 a 2 3 Terminal No.1 0.5 2.5 2.5 0.3 0.6 2 0.3 2 3.3 2 A Operating force with detent : a J b bJa } 1.51N{153102gf} } } 2.51.5N{255153gf} cJb bJc A Operating force with detent : 21.5N{204102gf} 2-2 Travel 2-3 13 Travel a 2b2 c 1.5 9 3.5 15 2 1.5 3.5 1.5 2 3.5 5.5 (8.5) 2 P.C.Board mounting face 3 3 3.5 P.C.Board mounting face 2 3.2 Terminal No. 1 Terminal No.1 Unit: (mm) 0.6 2.5 2.5 8.5 0.3 A 3.3 Operating force with detent : 1.51N{153102gf} 0.3 0.6 2 2 2 2 A Operating force with detent : a J b 1.51N{153102gf} } cJb 3.3 b J a 2.51.5N{255153gf} } b Jc Slide Switches 10 Order Number STSSS9121 STSSS9131 STSSS9221 STSSS9231 STSSS9132 STSSS9233 Model Direction of Knob Number of Poles Number of Positions Knob Length (mm) Change Over Timing Life (Cycles) Contact Resistance (m) Frame Style SSSS912N-4A-0 SSSS913Z-4A-0 SSSS922N-4A-0 SSSS923Z-4A-0 SSSS913Z-4A-1 SSSS923Z-4A-1 Vertical Vertical Vertical Vertical Horizontal Horizontal 1 1 2 2 1 2 2 3 2 3 3 3 4 mm 4 mm 4 mm 4 mm 4 mm 4 mm Non-shorting Non-shorting Non-shorting Non-shorting Non-shorting Non-shorting 10.000 10.000 10.000 10.000 10.000 10.000 30 m 30 m 30 m 30 m 30 m 30 m A A A A A A SSSS9 Series c Detail of knob 2or4+1 2or4 4.7 2 Travel 3-o0.7 +0.1 0 hole 2 3.5 1.4 2 2 P.C.Board mounting face 5 0.5 0.5 0.5 0.25 0.5 1 2 3 Terminal No.1 2 0.35 0.5 3.7 22 9 11.5 A c 1 2 3 11.5 2- 3 0. 4.7 2 A 0.5 Terminal No.1 Unit: (mm) 3-o0.7 +0.1 0 hole 3.5 1.4 5 5.5 3 0. C Travel 2 2or4 C 2P.C.Board mounting face 2 0.35 2 2 9 3.7 2 2 Rotary Switches 11 Order Number Model Number of Poles Number of Position Shaft Style Change Over Timing Shaft Length (mm) STSRBM141 STSRBM151 STSRBM161 SRBM14N-K20 SRBM15N-K20 SRBM16N-K20 1 1 1 4 5 6 KNURL KNURL KNURL Non-shorting Non-shorting Non-shorting 20 mm 20 mm 20 mm SRBM Series 1 Pole B L 0.3 12.5max. 10 0.7 5 5 Terminal No. 1 2 0.6 P.C.Board 0 mounting face 0.8 -0.2 6 5.5 0 1-0.2 M7G0.75 0.35 5.8 3 A 6.5 5.5 o6 5 6 P=2.5 2 to 4-Position REAR 5-Position a1 FRONT 5 1 4 321 5 43 2 REAR FRONT 5 4 1 3 2 6 -Position a2 1 5 4 3 a1.: Circuit steps are 2 to 5 positions at front, and 1 to 4 positions at rear. a2.: Circuit steps are 3 to 6 positions at front, and 1 to 4 positions at rear. a1,a2: It is necessary external wiring of common terminals. Unit: (mm) REAR FRONT 1 5 2 4 1 3 2 5 4 3 2 Tact Switches 12 Metal Contact (Standard Bulk Type) Order Number Model Operating Force (N) Life (Cycles) STTSKHCAA STTSKHCAC STTSKHCAE STTSKHCAG STTSKHCAB STTSKHCAD STTSKHCAF STTSKHCAH STTSKQEAA STTSKQEAC STTSKQEAB STTSKQEAD SKHCAA SKHCAC SKHCAE SKHCAG SKHCAB SKHCAD SKHCAF SKHCAH SKQEAA SKQEAC SKQEAB SKQEAD 1.274 N 2.548 N 0.735 N 1.274 N 1.274 N 2.548 N 0.735 N 1.274 N 1.568 N 2.548 N 1.568 N 2.548 N cycles 5 x 105 cycles 5 x 105 cycles 3 x 106 cycles 106 cycles 5 x 105 cycles 5 x 105 cycles 3 x 106 cycles 107 cycles 107 cycles 107 cycles 107 cycles Dimensions (mm) Joint Stem Type Joint Stem Type Joint Stem Type Joint Stem Type Flat Stem Type Flat Stem Type Flat Stem Type Flat Stem Type Joint Stem Type Joint Stem Type Flat Stem Type Flat Stem Type 106 (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) (12x12 mm) SKHC Series 5 3 1 2 3 4 4 3 It is suggested to use a P. C. board of 1.6 mm thick. Flat Stem Type 1.2 Stem Guide bosses o7.9 1 o1.6 9 12.5 1.5 3.5 o1.6 4.3 Stem 3.5 4.3 3 3.5 3.5 1.5 12.5 Either of two points o1.8 depression Guide bosses 3.8 Joint Stem Type 3 3.8 4 4-o1.2 hole 9 2 2-o1.8 hole 2 5 1 1 5 Circuit Diagram H12 H12 1 9 12.5 SKQE Series Circuit Diagram 5 4 3 3 o1.6 4 2-o1.7 hole 12.5 Stem 3 12.5 1 14 9 4 Guide bosses o7 Flat Stem Type o1.6 12.5 Unit: (mm) 5 3 2 1 1.5 3.5 4.3 3 1.5 Joint Stem Type 2 3.8 1.2 3 Guide bosses 1 9 2 Stem 3.5 4.3 1 4-o1.25 hole H12 5 H12 14 1 9 It is suggested to use a P. C. board of 1.6 mm thick. Tact Switches 13 Metal Contact (Standard Bulk Type) Order Number Model STTSKHKAA SKHKAA Operating Force (N) Life (Cycles) Initial contact resistance Stem color Case color cycles max. 100 m Light gray Black 5x105 1.274N Circuit diagram H12 2 5 1 3 1 2 3 4 4 Printed circuit board mounting hole dimensions (When viewed from switch mounting face) o6 Stem 3.5 5 3.35 12 4-o1.2holes 1 12.5 12.5 It is suggested to use a P.C.Board of 1.6mm thick. Unit: (mm) Tact Switches 14 Metal Contact (Standard Bulk Type) Order Number Model Operating Force (N) Life (Cycles) STTSKHCLA SKHCLA 1.274 N 5 x 105 cycles 12 5 o7.9 Horizontal type stem 7 Either of two points o1.8 depression 3.5 2.65 5.35 9.35 3.45 12.7 2 1 5 1 o1.6 10 2-o1.7Hole 3.5 Circuit diagram 3.5 6.7 0.5 1.5 0.7 0.3 2.5 2.5 1 2 Printed Circuit board mounting hole dimensions (When viewed from switch mounting face) Unit: (mm) 5 2-o1.2Hole 10 It is suggested to use a P.C. board of 1.6 mm thick Tact Switches 15 Metal Contact (Standard Bulk Type) Order Number Model STTSKHWAC STTSKHWAD STTSKHWAA STTSKHWAB STTSKHHAJ STTSKHHAL STTSKHHAQ STTSKHHBC STTSKHHAK STTSKHHAM STTSKHHDC STTSKHHAR STTSKHHCQ STTSKHHCR STTSKHHBV STTSKHHBW STTSKHHBY STTSKHHAN STTSKHHAP STTSKHHBS Operating Force (N) SKHWAC SKHWAD SKHWAA SKHWAB SKHHAJ SKHHAL SKHHAQ SKHHBC SKHHAK SKHHAM SKHHDC SKHHAR SKHHCQ SKHHCR SKHHBV SKHHBW SKHHBY SKHHAN SKHHAP SKHHBS 106 (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) (6x6 mm) SKHH Series 1 2 H6 4.5 4 3 2 Stem Stem 3 oA 3.5 3.5 h 3.6 3.5 o2.7 4 h H6 4.5 1 H= 4.3 mm H= 4.3 mm H= 5 mm H= 5 mm H= 4.3 mm H= 4.3 mm H= 4.3 mm H= 4.3 mm H= 5 mm H= 5 mm H= 5 mm H= 5 mm H= 5 mm H= 5 mm H= 7 mm H= 7 mm H= 7 mm H= 9.5 mm H= 9.5 mm H= 9.5 mm cycles 5 x 105 cycles 106 cycles 5 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 2 x 106 cycles 106 cycles 5 x 105 cycles 2 x 106 cycles 2 x 105 cycles 2 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 1.568 N 2.548 N 1.568 N 2.548 N 0.980 N 1.568 N 2.548 N 1.960 N 0.980 N 1.568 N 1.960 N 2.548 N 3.528 N 5.096 N 0.980 N 1.568 N 2.548 N 0.980 N 1.568 N 2.548 N SKHW Series Dimensions (mm) Life (Cycles) 0.7 Unit: (mm) 6.5 0.7 0.7 Tact Switches 16 Multifunction Tact Switch Order Number Model Operating Force (N) Life (Cycles) Dimension (mm) Type STTSKQUAA STTSKQUBA STTSKQUCA SKQUAA SKQUBA SKQUCA each direction 5x 5 x 104 each direction 1 x 105 each direction H = 7.1 mm (10 x 10 mm) H = 7.1 mm (10 x 10 mm) H = 10 mm (10 x 10 mm) Snap-in SMD Snap-in STTSKQUDB SKQUDB 1,568 N 1,568 N 1,568 N Center push: 3.136 N 1,568 N Center push: 3.136 N 1 x 105 each direction H = 8.6 mm (10 x 10 mm) SMD 104 Note: STEM colour: Black, Ratings (max.): 50mA 12VDC SKQUBA H3.8 4 C Stem rotational center 1.23 H10 H3 Circuit diagram Circuit diagram A1 5D Reflow pattern (When viewed from the switch mounting face) holes 10.3 1.5 ho 1.3 6.5 1.5 11.6 8.8 0.45 s le o1 2- 4 Common 6.5 3.5 Printed circuit board mounting hole dimentions (When viewed from the switch mounting face) 5D C3 7.1 4 Common B2 0.45 C3 3.15 7.1 B2 3.15 A1 H3 4-o1.2 SKQUDB o6 A 6 5.75 1 0.9 5.75 A o6 6 0.9 SKQUCA 1 0.9 0.45 0.9 5 3 Stem rotational center 1.23 6.5 2 0.45 5 4 D B 6.5 2 H3.8 C H10 6 A 0.9 D B 3 1 0.9 6 A 0.7 1 0.7 SKQUAA H3.2 C H10 10.7 4 0.9 3 6.5 5.75 Stem rotational center 1.23 5 0.45 Stem rotational center 1.23 Circuit diagram Circuit diagram 6 Center A 1 6 Center 5 D B 2 5 D C 3 4 Common 2.8 6.5 4-o1.2 3.15 Printed circuit board mounting hole dimentions (When viewed from the switch mounting face) 5.8 8.6 4 Common C 3 Reflow pattern (When viewed from the switch mounting face) holes 11.6 8.8 1.5 B 2 5.8 3.5 3.15 10 A 1 s 10.3 1.3 ho 1.5 o1 2- 0.45 le Unit: (mm) 6.5 4 C H10 D 2 0.45 H3.2 0.7 0.7 5 0.9 3 6.5 B 2 0.45 5.75 B D Tact Switches 17 Metal Contact (Standard Bulk Type) Order Number Model STTSKHVBA STTSKHVBB STTSKHVBC STTSKHVBD STTSKHVBE STTSKHVBF STTSKHVBK STTSKHVBL STTSKHVBM STTSKHVBG STTSKHVBH STTSKHVBJ SKHVBA SKHVBB SKHVBC SKHVBD SKHVBE SKHVBF SKHVBK SKHVBL SKHVBM SKHVBG SKHVBH SKHVBJ Operating Force (N) Life (Cycles) Dimensions (mm) H= 4.3 mm H= 4.3 mm H= 4.3 mm H= 5 mm H= 5 mm H= 5 mm H= 7 mm H= 7 mm H= 7 mm H= 9.5 mm H= 9.5 mm H= 9.5 mm cycles 5 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 106 0.980 N 1.586 N 2.548 N 0.980 N 1.568 N 2.548 N 0.980 N 1.568 N 2.548 N 0.980 N 1.568 N 2.548 N (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) SKHV Series Standard Type 12.7 6.35 6.35 Stem H6 0.4 h A 4.3 3.5 5 3.5 7 3.3 9.5 3 0.3 oA Circuit Diagram 3.5 h 0.5 1 9 18 2 5 o4 18 5 1 2 Printed Circuit board mounting hole dimensions (When viewed from switch mounting face) 12.7 2-o1hole 5 It is suggested to use a P. C. board of 1.6 mm thick. Unit: (mm) Tact Switches 18 Metal Contact (Standard Bulk Type) Order Number Model STTSKQNAA STTSKQNAB STTSKQNAC STTSKQNAD STTSKQNAE STTSKQNAF STTSKQNAH STTSKQNAJ STTSKQNAK STTSKQNAL STTSKQNAM STTSKQNAN SKQNAA SKQNAB SKQNAC SKQNAD SKQNAE SKQNAF SKQNAH SKQNAJ SKQNAK SKQNAL SKQNAM SKQNAN Operating Force Life (Cycles) Stem color Stem height 0.98 N 1.568 N 2.548 N 0.98 N 1.568 N 2.548 N 0.98 N 1.568 N 2.548 N 0.98 N 1.568 N 2.548 N cycles 5x 5 x 105 cycles 2 x 105 cycles 5 x 105 cycles 5 x 105 cycles 2 x 105 cycles 5 x 105 cycles 5 x 105 cycles 2 x 105 cycles 5 x 105 cycles 5 x 105 cycles 2 x 105 cycles Black White Gray Black White Gray Black White Gray Black White Gray h = 4.3 mm h = 4.3 mm h = 4.3 mm h = 5 mm h = 5 mm h = 5 mm h = 7 mm h = 7 mm h = 7 mm h = 9.5 mm h = 9.5 mm h = 9.5 mm 105 SKQN Series h A 4.3 3.4 5 3.4 7 3.2 9.5 2.9 Circuit diagram 1 2 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) 12.7 6.35 6.35 2-o1hole 1 2 o0.5 9 18 5 5 Mounting surface Unit: (mm) 3.3 h 0.5max. o4 18 o6 oA 12.7 Tact Switches 19 Metal Contact (Standard Bulk Type) Order Number Model STTSKHHLM STTSKHHLN STTSKHHLP STTSKHHLQ STTSKHHLR STTSKHHLS STTSKHHLU STTSKHHLV STTSKHHLW SKHHLM SKHHLN SKHHLP SKHHLQ SKHHLR SKHHLS SKHHLU SKHHLV SKHHLW Operating Force (N) Life (Cycles) 0.980 N 1.568 N 2.548 N 0.980 N 1.568 N 2.548 N 0.980 N 1.568 N 2.548 N cycles 5 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 106 cycles 5 x 105 cycles 2 x 105 cycles 106 Dimensions (mm) L= 3.85 mm L= 3.85 mm L= 3.85 mm L= 8.35 mm L= 8.35 mm L= 8.35 mm L= 5.85 mm L= 5.85 mm L= 5.85 mm (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) SKHHL Series Vertical Type Circuit diagram 1 2 Printed circuit board mounting hole dimensions (When viewed from switch mounting face) oA 7.5 Stem 4 2-o1.3hole 4 7.1 2.5 0.3 6.2 3.5 4.5 7 1 0.7 4.5 7 Unit: (mm) 0.7 2 0.3 2.55 2.5 R 4 1 It is suggested to use a P.C.Board of 1.6mm thick. 2-o1hole Tact Switches 20 Metal Contact with LED Order Number Model Operating Force (N) STTSKHQFF STTSKHJGE STTSKECFK STTSKECFL STTSKECFS SKHQFF SKHJGE SKECFK SKECFL SKECFS 1.568 N 2.548 N 0.784 N 0.784 N 0.784 N Dimensions (mm) Life (Cycles) with LED: red (6 x 6 mm) with LED: red (8 x 8 mm) with LED: red (8 x 8 mm) with LED: pure green (8 x 8 mm) with LED: amber (8 x 8 mm) 104 5x 2 x 105 1 x 105 1 x 105 1 x 105 SKHQ Series With LED Type Circuit diagram 1 2 0.8 Stem H6 6 4.95 1 2 3 4 5 6 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) 0.7 5 4 3.5 4.5 7 3.1 4.8 0.7 3.6 6-o1hole 0.5 5 6.5 0.2 0.2 5 6 4.5 5 4 3 It is suggested to use a P.C.Board of 1.6mm thick. 6.5 SKHJ Series With LED Type 4.6 5 Stem 2 Circuit diagram 8 2 3 5 4 6 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) 5 4 2-o1 hole 3.5 3 4.5 6 3 2 8.5 1 1 0.5 7.5 0.2 0.2 0.7 6 0.7 7 5 4-o1 hole SKEC Series With LED Type Unit: (mm) 7.5 7 4 4.5 3 It is suggested to use a P.C.Board of 1.6mm thick. Tact Switches 21 Mechanical Contact (SMD Type) Order Number Model STTSKHMPS STTSKHMPW STTSKHMPU STTSKHUAB STTSKHUAD STTSKHUAF SKHMPS SKHMPW SKHMPU SKHUAB SKHUAD SKHUAF Operating Force (N) Life (Cycles) Dimensions (mm) H= 3.1 mm H= 3.1 mm H= 3.1 mm H= 2.5 mm H= 2.5 mm H= 2.5 mm 105 0.980 N 1.568 N 2.352 N 0.980 N 1.568 N 2.548 N 5x 3 x 105 2 x 105 3 x 105 3 x 105 105 (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) (6 x 6 mm) SKHM Series Reflow Soldering Type 1 2 8 6.2 1 2 3 5 4 0.7 0.7 4.5 Circuit diagram 5 0.7 6.2 Printed circuit board land dimensions (When viewed from the switch mounting face) 3 4 8.4 o3 3.1 2.6 4.5 Stem 5-1.4G1.6 land SKHU Series Reflow Soldering Type 7.2 6.2 2 Unit: (mm) 2 h 1.2 1 2 2 3 4 2.5 5 9.5 4 3.1 5.4 Stem h 1.4 4 Printed circuit board land dimensions (When viewed from switch mounting face) 2.6 3 Circuit diagram 5.8 o3 0.7 4 6 1 Tact Switches 22 Mechanical Contact (SMD Type) Order Number Model STTSKQYAA STTSKQYAB STTSKQYAC SKQYAA SKQYAB SKQYAC Operating Force (N) 1.568 N 2.548 N 0.98 N Life (Cycles) Dimensions (mm) H= 2.5 mm (3.7 x 6.1 mm) H= 2.5 mm (3.7 x 6.1 mm) H= 2.5 mm (3.7 x 6.1 mm) 104 5x 5 x 104 5 x 104 SKQYA Series 6.8 6.1 2.6 1 2 Circuit diagram 2 Printed circuit board land dimensions (When viewed from the switch mounting face) Stem 8 4 2.5 3 Unit: (mm) 1 5.3 3 o1.8 3.7 1.2 2.9 0.8 1 3 2.7 4.7 Tact Switches 23 Metal Contact Order Number Model STTSKQRAA STTSKQRAC SKQRAA SKQRAC Operating Force (N) Life (Cycles) Dimensions (mm) 1.568 N 2.352 N 5x cycles 5 x 104 cycles Height = 0,5 mm Height = 0,5 mm 105 SKQRA Series Circuit diagram 2 1 2.8 4.8 4.2 3 4 4 1.9 3.7 5 d de a en e m ar m g co atin Re per o .8 o0 2.8 1.7 4.8 0.5 2 Printed circuit board land dimensions (When viewed from the switch mounting face) 3 Unit: (mm) 1 0.6 0.6 Tact Switches 24 Elastic Contact (Standard Bulk Type) Order Number Model STTSKEYAG STTSKEYAF STTSKEYAC STTSKPEAA STTSKPGAA STTSKPGAC SKEYAG SKEYAF SKEYAC SKPEAA SKPGAA SKPGAC Operating Force (N) Dimensions (mm) Life (Cycles) H= 5 mm H= 5 mm H= 5.5 mm H= 5 mm H= 5 mm H= 5 mm 105 0.784 N 1.176 N 2.450 N 2.450 N 2.450 N 1.176 N 5x 3 x 105 105 5 x 104 5 x 104 5 x 104 (8 x 8 mm) (8 x 8 mm) (8 x 8 mm) (6.3 x 6.6 mm) (6.3 x 6.6 mm) (6.3 x 6.6 mm) SKEY Series H7.8 2 h Circuit diagram 5 1 2 3 4 5.5 4.5 1 3 4 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) Rubber dome o3.5 3.5 4.5 3 h 8.5 8.5 0.7 0.7 4-o1hole It is suggested to use a P.C. Board of 1.6mm thick. SKPE Series 6.6 Circuit diagram 2.5 2 6.3 1 Stem 0.2 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) 1 2 3.5 3.3 5 6.5 It is suggested to use a P.C. Board of 1.6mm thick. 6.5 2-o1.3 hole 1 8.1 5.8 SKPG Series 8.6 6.6 2 Circuit diagram 1 6.3 4.5 1 Stem 2 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) 2.5 9.8 0.2 1 Unit: (mm) 5.8 2.4 3.3 5 6.8 It is suggested to use a P.C. Board of 1.6mm thick. Tact Switches 25 Elastic Contact (with LED) Order Number Model Operating Force (N) Lifetime (Cycles) Travel Dimensions (mm) Actuator Material STTSKRAAA STTSKRAAB STTSKRAAC STTSKRAAD SKRAAA SKRAAB SKRAAC SKRAAD 3.0 N 4.5 N 2.0 N 3.5 N 5 x 105 3 x 105 1 x 106 5 x 105 0.35 mm 0.40 mm 0.50 mm 0.75 mm H = 3.4 mm H = 3.4 mm H = 5.1 mm H = 5.1 mm Silicone Silicone Silicone Silicone SKRA Series 6.8 6.2 0.7 Circuit diagram 2 6.2 4 3 4 Stem 0.1 2.5 h 3 a 2 Printed circuit board land dimension (When viewed from the switch mounting face) 4 3 1 Unit: (mm) h (mm) 3.4 5.1 a (mm) o3 o2.6 3 8.5 5 1 Tact Switches 26 Metal Contact / Soft feeling Type Order Number Model STTSKPLAA STTSKPLAB SKPLAA SKPLAB Operating Force (N) Life (Cycles) 105 2.45 N 1.96 N 1x 1 x 105 Dimensions (mm) Travel H= 5.0 mm Diameter 6.4 mm H= 5.0 mm Diameter 6.4 mm 1.3 mm 1.3 mm SKPLAA Series 12.7 6.35 6.35 o4.55 o6.45 2 o0.5 9 18 3.5 5 1 5 18 5 o4 12.7 Circuit diagram 1 Unit: (mm) 2 Printed circuit board mounting hole dimensions (When viewed from the switch mounting face) 5 2-o0.9 hole Compact Stick Switch 27 Order Number Model Switch ratings Contact resistance lever/ push operation Insulation resistance Voltage proof Operating life STRKJXL01 RKJXL DC5V10mA 500m/500m max. 100M min. at 250V DC 300V AC for 1 minute 100,000 cycles Features: 8 - direction switcher with push-on selector sw (Version without push-on switch is also available) RKJXL 13.4 3.5 6.4 Y (15) 3.5 o2.2 3.5 H B X G C 1.4 4-13 24 Center of shaft rotation A D X' F E 25 Y' H 5 .0 o1 A Y G 1 B C1 A B C D X' C2 E F G H 4- 2. 5 X C1 45 10.8 12-o1 o14.8 45 C2 2 F .6 D o1 C Y' The following terminals conduct according to the operational direction of the shaft. (Adjoining terminals have a shorting zone) E Mounting hole detaile viewed from mounting side H A D E C1 C2 1 2 (C1) and (C2) conduct between (H)-(A) and (D)-(E). (1)-(2) conduct by push- on operation. A B 1 H C2 C G C1 F D E SW Circuit Unit: (mm) 2 Rotary Potentiometer 28 Order Number Size (mm) Number of Elements Resistance Value (k) STRK09701 STRK09702 STRK09703 STRK09704 STRK09705 STRK09706 STRK09707 STRK09708 STRK09709 STRK09710 STRK09711 STRK09712 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit 10 k 50 k 100 k 10 k 50 k 100 k 2x10 k 2x50 k 2x100 k 2x10 k 2x50 k 2x100 k Standard Specifications: Rotational Life: Rotational Angle: Rotational Torque: Resistance Tolerance: Rated Power: max. Operating Voltage (DC): max. Operating Voltage (AC): Insulation Resistance: Taper Shaft lenght (mm) A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 15000 Cycles 300 +/- 5 Degrees 30 - 250 gf/cm +/- 20% 0.05 W DC 10 V AC 50 V 100 M min. at 500 V DC RK097 Series Single Unit Number of Shafts: Details: Shaft Style: Terminals: Detents: Attachement: Tap Mounting height (mm) Uses Rest of Specification No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Single Shaft Horizontal Type Slotted Printed Wiring No Detent No Dual Unit 9.55 9.5 9.5 LB 1 2 0.8 3 0.9 R2 R1 0.9 Slotted Type L1 LB Not specitied slotting angle. o6 1 1.6 M7G0.75 Unit: (mm) C0.5 1 2 0.8 3.5 R1 3 3.5 6.5 LB L1 4.85 L1 4.85 7.05 Rotary Potentiometer Order Number Size (mm) STRK16301 STRK16302 STRK16303 STRK16304 STRK16305 STRK16306 STRK16307 STRK16308 STRK16309 STRK16310 STRK16311 STRK16312 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm 16 mm Number of Elements Resistance Value (k) 10 k Single Unit 50 k Single Unit 100 k Single Unit 10 k Single Unit 50 k Single Unit 100 k Single Unit 2x10 k Dual Unit 2x50 k Dual Unit Dual Unit 2x100 k 2x10 k Dual Unit 2x50 k Dual Unit Dual Unit 2x100 k Standard Specifications: Rotational Life: Rotational Angle: Rotational Torque: Resistance Tolerance: Rated Power: max. Operating Voltage (DC): max. Operating Voltage (AC): Insulation Resistance: 29 Taper Shaft lenght (mm) A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 15000 Cycles 300 +/- 5 Degrees 30 - 250 gf/cm +/- 20% 0.05 W - 0,1 W Depending on Taper DC 20 V AC 150 V 100 M min. at 500 V DC Tap Mounting height (mm) Uses Rest of Specification No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap No Tap 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Volume Control Volume Control Volume Control Tone Control Tone Control Tone Control Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Number of Shafts: Details: Shaft Style: Terminals: Detents: Attachement: 1 Horizontal Type Slotted Printed Wiring No Detent No RK163 Series 10.5 L1 L1 LB LB 3.8 1 R1 2 3 1 15 M7G0.75 12.1 60 Unit: (mm) 3-o1.2 hole Mounting hole detail viewed from mounting side L1 LB 5 5 5 5 3.8 1 2 15 3 1 Mounting surface 12.5 R2 R1 For tap terminal 6-o1.2 hole 4 o16 Shaft shown in full CCW position For tap terminal Mounting surface 12.5 C0.5 4 o6 1 o16 5 5 5 1.6 Mounting hole detail viewed from mounting side Rotary Potentiometer 30 Order Number Size (mm) Number of Elements Resistance Value (k) STRK09K01 STRK09K02 STRK09K03 STRK09K04 STRK09K05 STRK09K06 STRK09K07 STRK09K08 STRK09K09 STRK09K10 STRK09K11 STRK09K12 STRK09K13 STRK09K14 STRK09K15 STRK09K16 STRK09K17 STRK09K18 STRK09K19 STRK09K20 STRK09K21 STRK09K22 STRK09K23 STRK09K24 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit Dual Unit 10 k 50 k 100 k 10 k 50 k 100 k 10 k 50 k 100 k 10 k 50 k 100 k 2x10 k 2x50 k 2x100 k 2x10 k 2x50 k 2x100 k 2x10 k 2x50 k 2x100 k 2x10 k 2x50 k 2x100 k Standard Specifications: Rotational Life: Rotational Angle: Rotational Torque: Resistance Toleranz: Rated Power: max. Operating Voltage (DC): max. Operating Voltage (AC): Insulation Resistance: RK09K Series Unit: (mm) Taper Shaft lenght (mm) Shaft Style Mounting height (mm) Uses Details B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob Knob 10 mm 10 mm 10 mm 10 mm 10 mm 10 mm Vertical Vertical Vertical Vertical Vertical Vertical 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm Vertical Vertical Vertical Vertical Vertical Vertical AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical Single Unit: 5000 Cycles 280 +/- 5 Degrees 10 - 80 gf/cm 20% +/0.05 W Single Unit DC 20 V AC 50 V 100 M min. at 250 V DC Dual Unit: 10000 Cycles 280 +/- 5 Degrees 10 - 80 gf/cm 20% +/0.03 W Dual Unit DC 0 V AC 50 V 100 M min at 250 V DC Number of Shafts: Terminals: Detents: Attachement: Tap: 1 Printed Wiring No Detent No No Rotary Potentiometer Order Number Size (mm) Number of Elements Resistance Value (k) STRK09D01 STRK09D02 STRK09D03 STRK09D04 STRK09D05 STRK09D06 STRK09D07 STRK09D08 STRK09D09 STRK09D10 STRK09D11 STRK09D12 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm 9 mm Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit 10 k 50 k 100 k 10 k 50 k 100 k 10 k 50 k 100 k 10 k 50 k 100 k Standard Specifications: Rotational Life: Rotational Angle: Rotational Torque: Resistance Toleranz: Rated Power: max. Operating Voltage (DC): max. Operating Voltage (AC): Insulation Resistance: RK09D Series Unit: (mm) 31 NEW Taper Shaft lenght (mm) A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 25 mm 5000 Cycles 300 +/- 5 Degrees 1 to 8 mM.m 20% +/0.05 W DC 20 V AC 50 V 100 M min. at 250 V DC Number of Shafts: Bushing: Terminals: Detents: Attachement: Tap: Tap Mounting height (mm) Uses Details Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm 6.5 mm Vertical Vertical Vertical Vertical Vertical Vertical AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical 1 with Collar Printed Wiring No Detent No No Rotary Potentiometer 32 Order Number Size (mm) Number of Elements Resistance Value (k) STRK11K01 STRK11K02 STRK11K03 STRK11K04 STRK11K05 STRK11K06 STRK11K07 STRK11K08 STRK11K09 STRK11K10 STRK11K11 STRK11K12 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit Single Unit 10 k 50 k 100 k 10 k 50 k 100 k 10 k 50 k 100 k 10 k 50 k 100 k Shaft Style Mounting height (mm) Uses Details B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic B= Linear B= Linear B= Linear A= Logarithmic A= Logarithmic A= Logarithmic 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm 12.5 mm Vertical Vertical Vertical Vertical Vertical Vertical AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical Number of Shafts: Details: Shaft Style: Terminals: Detents: Attachement: with bushing: 15000 Cycles 300 5 Degrees 30 - 200 gf/cm 20% 0.05 W DC 20 V AC 50 V 100 M min. at 500 V DC No RK11K Series Horizontal Type 1 Horizontal Type/Vertical Type Flat Printed Wiring No Detent No M9x0.75 11 8 7.5 (3.5) 2 6.6 (8) Mounting surface 3.3 F10 10.9 5.4 7.5 M9G0.75 2.5 (7.5) 10.2 Standard Specifications: Rotational Life: Rotational Angle: Rotational Torque: Resistance Tolerance: Rated Power: max. Operating Voltage (DC): max. Operating Voltage (AaC): Insulation Resistance: Tap: Taper Shaft lenght (mm) 4-o1 hole 2.1 0.8 (1.6) (3.2) F H=12.5 is also compatible. 11 8 (7.5) M9G0.75 6.6 13 9.1 (8) 10 10.9 2 5.4 2 11 RK11K Series Vertical Type Mounting hole detail viewd from mounting side 9.4 (12) 2.1 2 2.6 6.1 (3.2) 2.5 (3.5) 7.5 4-o1 hole Mounting surface Unit: (mm) Mounting hole detail viewd from mounting side Rotary Potentiometer Order Number Size (mm) Number of Elements Resistance Value (k) STRK27101 STRK27102 STRK27103 STRK27104 27 mm 27 mm 27 mm 27 mm Dual Unit Dual Unit Dual Unit Dual Unit 2x10 k 2x20 k 2x50 k 2x100 k 33 Taper Shaft lenght (mm) A= Logarithmic A= Logarithmic A= Logarithmic A= Logarithmic 20 mm 20 mm 20 mm 20 mm Motor version is also available Standard Specifications: Rotational Life: 15000 Cycles Gang Error (-60dB to 0 dB = 2 dB max) Rotational Angle: 300 3 Degrees Rotational Torque: 80 - 350 gf/cm Resistance Tolerance: 20% Tap Mounting height (mm) Uses Rest of Specification No Tap No Tap No Tap No Tap 12.5 mm 12.5 mm 12.5 mm 12.5 mm AC-Use AC-Use AC-Use AC-Use Standard Standard Standard Standard Rated Power: 0.05 W - 0.1 W Depending on Taper max. Operating Voltage (DC): max. Operating Voltage (AC): 30 V Insulation Resistance: 100 M min. at 500 V DC Number of Shafts: Details: Shaft Style: Terminals: Detents: Attachement: 1 Horizontal Type Slotted Printed Wiring No Detent No RK27 Series 27 10 L1 25.3 For tap terminals 10 5 L2 R1 2 M8G0.75 1 1 2 3 4 12 o3 R2 12.5 24.5 5 5 5 7 6-o1.2 hole Mounting surface Mounting hole detail viewed from mounting side Slotted Type Not specified slotting angle L1 7 L1 o6 1 1.6 M9G0.75 Unit: (mm) C0.5 10 15 20 25 30 Slide Potentiometer 34 Order Number Travel of lever (mm) Number of Elements Resistance Value (k) STRS30101 STRS30102 STRS30103 30 mm 30 mm 30 mm Single Unit Single Unit Single Unit 10 k 50 k 100 k Standard Specifications: Sliding Life: Resistance Tolerance: Rated Power: Max. Operating Voltage (AC): Insulation Resistance: Taper Lever lenght (mm) Tap Terminal Uses Rest of Specification B= Linear B= Linear B= Linear 20 mm 20 mm 20 mm No Tap No Tap No Tap Printed Wiring Printed Wiring Printed Wiring AC-Use AC-Use AC-Use Standard Standard Standard 15000 Cycles 20% 0,025 - 0,2W Depending on Type and Taper 50 - 200V Depending on Type and Taper 100 M at 250 VDC Number of Levers: Details: Detents: Attachement: 1 Vertical Type No Detent No RS30 Series S+15 Travel S+11 t =1.2 4 L1 10 S Travel 5 6.6 S+5 2 4 3 4-o1.5hole 1 3.75 Unit: (mm) 3.5 7 (1) 3 L1 (1) 0.5 8.5 8 3 2-M2 Slide Potentiometer Order Number Travel of lever (mm) Number of Elements Resistance Value (k) STRSA0N11S STRSA0N12S STRS60N11S STRS60N12S 100 100 60 60 single single single single 10 k 10 k 10 k 10 k 35 Taper Lever lenght (mm) Lever Uses Rest of Specification A= Logarithmic B= Linear A= Logarithmic B= Linear 8.2 8.2 8.2 8.2 T-Bar T-Bar T-Bar T-Bar AC-Use AC-Use AC-Use AC-Use Printed wiring terminals Printed wiring terminals Printed wiring terminals Printed wiring terminals RSA0N11S Series Standard type 8.4 128 120 2M 3 8 L 100 Travel 3.5 Mounting surface 3o 1.5 ho les 127.5 82.2 (42.1) 40.1 1 3 2-o 2 ho le s Viewed from the mounting side Lead terminal is available Unit: (mm) 3.75 2 Slide Potentiometer 36 Order Number Travel of lever (mm) Number of Elements Resistance Value (k) STRS60N01 STRS60N02 STRS60N03 STRS60N04 STRS60N05 STRS60N06 STRS60N07 STRS60N08 STRSA0N01 STRSA0N02 STRSA0N03 STRSA0N04 STRSA0N05 STRSA0N06 STRSA0N07 STRSA0N08 60 mm 60 mm 60 mm 60 mm 60 mm 60 mm 60 mm 60 mm 100 mm 100 mm 100 mm 100 mm 100 mm 100 mm 100 mm 100 mm Single Unit Single Unit Dual Unit Dual Unit Single Unit Single Unit Dual Unit Dual Unit Single Unit Single Unit Dual Unit Dual Unit Single Unit Single Unit Dual Unit Dual Unit 10 k 10 k 2x10 k 2x10 k 10 k 10 k 2x10 k 2x10 k 10 k 10 k 2x10 k 2x10 k 10 k 10 k 2x10 k 2x10 k Sliding Life: Resistance Tolerance: Rated Power: Max. Operating Voltage AC: Insulation Resistance: Taper Lever lenght (mm) Details Lever Type Uses Rest of Specification A=Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear 8.2 mm 8.2 mm 8.2 mm 8.2 mm 12 mm 12 mm 12 mm 12 mm 8.2 mm 8.2 mm 8.2 mm 8.2 mm 12 mm 12 mm 12 mm 12 mm Crank Lever Crank Lever Crank Lever Crank Lever Vertical Vertical Vertical Vertical Crank Lever Crank Lever Crank Lever Crank Lever Vertical Vertical Vertical Vertical 9-2 (T-Bar) 9-2 (T-Bar) 9-2 (T-Bar) 9-2 (T-Bar) 1 1 1 1 9-2 (T-Bar) 9-2 (T-Bar) 9-2 (T-Bar) 9-2 (T-Bar) 1 1 1 1 AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Detents: Attachement: Terminals: Tap: No Detent No Printed Wiring No 15000 Cycles 20% +/0,1 - 0,5 W Depending on Type and Fader 150 - 500 V Depending on Type and Fader 100 M at 250 VDC 16 18.5 14.5 o1 6- F 2 3 3 2 Single unit o1 .5 3 62 1 3 2-o 2.2 hole 1 2 Mounting surface-A 1 2 12.3 H E F 3 C D 12 1 1 ho le Mounting surface-A 13.1 8 Dual unit 2 3 1 3 1 L1 2 21 12 Dual unit Dimensions S A B C D E F Model RS60N 60 88 80 87.5 51.7 RSA0N 100 128 120 127.5 82.5 (43.7) 38.8 1 S Travel 3 1 ole 3.5 8 L1 Mounting surface-B Unit: (mm) 2h E Mounting surface Length 2 3 S Travel 8,2 Configuration Code Single unit 3 2-o 3.7 4 Length 8.2 1.5 8 Dimensions 2 1 1 2 3.75 11.25 2-M .5 C D 3 Dimensions ho A B 9-2 (T-BAR) 3.75 11.25 Configuration Code le RS60N & RSA0N Series Dimensions S C D E F Model RS60N 60 80 88 87.5 74 RSA0N 100 120 128 127.5 114 Mounting hight : H = 6.5, 10 Slide Potentiometer Order Number Travel of lever (mm) Number of Elements Resistance Value (k) STRSA0K01 STRSA0K02 STRSA0K03 STRSA0K04 STRSA0K05 STRSA0K06 STRSA0K07 STRSA0K08 STRSA0K09 STRSA0K10 STRSA0K11 STRSA0K12 100 100 100 100 100 100 100 100 100 100 100 100 Single Unit Single Unit Dual Unit Dual Unit Single Unit Single Unit Dual Unit Dual Unit Single Unit Single Unit Dual Unit Dual Unit 10 k 10 k 2x10 k 2x10 k 10 k 10 k 2x10 k 2x10 k 10 k 10 k 2x10 k 2x10 k Sliding Life (Carbon Type): Sliding Life (Conductive Plastic): Resistance Tolerance: Rated Power: Max. Operating Voltage AC: Insulation Resistance: 37 Taper Lever lenght (mm) Details Lever Type Uses Rest of Specification A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear A= Logarithmic B= Linear 12 mm 12 mm 12 mm 12 mm 8.2 mm 8.2 mm 8.2 mm 8.2 mm 12 mm 12 mm 12 mm 12 mm Carbon Type Carbon Type Carbon Type Carbon Type Conductive Plastic* Conductive Plastic* Conductive Plastic* Conductive Plastic* Carbon Type* Carbon Type* Carbon Type* Carbon Type* 1 1 1 1 9-2 (T-Bar) 9-2 (T-Bar) 9-2 (T-Bar) 9-2 (T-Bar) 1 1 1 1 AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use AC-Use Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard 100K Cycles 300K Cycles 20% +/0,25 - 0,5 W Depending on Type and Fader 350V - 500V Depending on Type and Fader 100 M min. at 250V DC Detents: Attachement: Terminals: Tap: : * No Detent No Lead Wiring/Connector No With micro switch RSA0K Series Configuration Code 1 A B S(travel) Mounting surface 2-M3 Length 12 6 -o 1.8 3 1 2 31 2 hol e Terminal No. Circuit diagram Configuration Code Dimensions 9-2 (T-BAR) 18.5 14.5 1.5 L1 4 8 Length Unit: (mm) 8,2 13.9 7 1 32 L1 8 L1 Dimensions 3 1 2 312 The single unit is not provided with terminals (1)(2)(3). Dimensions B S A Model 60 80 92.6 RS60K 100 120 132.6 RSA0K 38 NEW Hollow Shaft Rotary Encoder Order Number Model Size Number of Pulses Detents Details Life time (Cycles) Rating STEC10E01 EC10E1220501 10 mm 12 24 Vertical Type 100.00 min. 1mA, 5 VDC EC10E1220501 Unit: (mm) Dual Shaft Encoder & Pop-Up Encoder 39 NEW Details Shaft lenght (mm) 30 Vertical type 20 15 30 Vertical type 20 15 30 Vertical type refer to drawing Number of Pulses Detents Order Number ALPS P/N Size (mm) STEC11E01 EC11EBB24C 11 15 STEC11E02 EC111XXXXX 11 STEC11E03 EC11E1524U 11 Standard Specification: Ratings: Insulation resistance: Withstand Voltage: Life cycles: Encoder 10 mA 5 VDC 250 VDC 1 mA, 100 MOhm MIN 300 VAC 15000 Standard Specification: Ratings: Insulation resistance: Withstand Voltage: Life cycles: Self return switch 10 mA 5 VDC 250 VDC 1 mA, 100 MOhm MIN 300 VAC 15000 EC11E Series Unit: (mm) Attachement inner shaft: Encoder and push-on switch outer shaft: Encoder inner shaft: Encoder and push-on switch outer shaft: Self-return switch encoder with push-lock switch Push-On Switch 0,5 A 16 VDC (1 mA MIN) 250 VDC 1 mA, 100 MOhm MIN 300 VAC 20000 Rest of Specification Standard Standard Standard Push-Lock Switch 0,5 A 12 VDC (1 mA MIN) 50 VDC 1 mA, 10 MOhm MIN 300 VAC 10000 Rotary Encoder 40 Order Number Size (mm) Number of Pulses Detents STEC11B01 STEC11B02 STEC11B03 STEC11B04 STEC11B05 STEC11B06 STEC11B07 STEC11B08 STEC11B09 STEC11B10 STEC11B13 STEC11B12 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 11 mm 15 15 15 15 15 15 15 15 20 20 20 20 30 30 30 30 30 30 30 30 20 20 20 20 Standard Specifications: Ratings: max. Operating Current: Insulation Resistance: Withstand Voltage Life cycles Details Shaft lenght (mm) Shaft Style Attachment Rest of Specification Horizontal Type Horizontal Type Vertical Type Vertical Type Horizontal Type Horizontal Type Vertical Type Vertical Type Horizontal Type Horizontal Type Vertical Type Vertical Type 25 mm 25 mm 25 mm 25 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm Slotted Slotted Slotted Slotted Flat Flat Flat Flat Flat Flat Flat Flat Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard 10mA 5 VDC 10mA 300V DC 10 M min. 300V AC 15.000 cycles Number of Shafts: 1 Terminals: Printed Wiring Attachement: No EC11B Horizontal EC11B Vertical Unit: (mm) BUSHING M7x0.75 H 6.6 LB 7 Rotary Encoder Order Number Size (mm) Number of Pulses Detents STEC16B01 STEC16B02 STEC16B03 STEC16B04 16 mm 16 mm 16 mm 16 mm 24 24 24 24 Without Detent 24 Without Detent 24 Standard Specifications: Ratings: max. Operating Current: Insulation Resistance: Withstand Voltage: 41 Details Shaft lenght (mm) Shaft Style Horizontal Type Horizontal Type Vertical Type Vertical Type 25 mm 25 mm 25 mm 25 mm Flat Flat Flat Flat Rest of Attachement Specification No No No No 0,5mA 5 VDC 0,5mA 50V DC 10 M min. 50V AC EC16B Horizontal 7.5 L1 C 2 10 3 -o 1. 2 2.1 ho le 4 (3.2) (3.5) o3 Mounting hole detail viewed from mounting side 13.5 (15.9) 2 2.6 B 14.4 8.5 12.5 12.5 9 o6 o12.5 8.3 4.5 R1 M9 0.75 2 Mounting surfacce 3.1 A LB 16 9.3 7.5 EC16B Vertikal 2 2.1 10.5 8.5 A 10 -o o3 1. 2 ho 3.5 M9G0.75 2 C 4 3 3.3 B le 12.5 9 o12.5 8.3 R1 4.5 o6 4.6 2 16.8 16 L1 LB 9.3 6.5 Mounting hole detail viewed from mounting side Unit: (mm) Standard Standard Standard Standard Rotary Encoder 42 Order Number Size (mm) Number of Pulses Detents Details Shaft lenght (mm) STEC12E01 STEC12E02 STEC12E03 STEC12E04 STEC12E05 STEC12E06 STEC12E07 STEC12E08 STEC12E09 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 12 12 12 24 24 24 24 24 12 12 12 12 24 24 24 24 24 Horizontal Type Horizontal Type Vertical Type Vertical Type Horizontal Type Horizontal Type Vertical Type Vertical Type Vertical Type 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm - Standard Specifications: Ratings: max. Operating Current: Insulation Resistance: Withstand Voltage: STEC12E01 STEC12E05 STEC12E02 STEC12E06 STEC12E03 STEC12E07 STEC12E04 STEC12E08 Unit: (mm) Shaft Style Flat Flat Flat Flat Flat Flat Flat Flat Attachment No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm No Push-On Switch 0,5 mm Hollow shaft No 0,5mA 5 VDC 0,5mA 50V DC 10 M min. 50V AC STEC12E09 Rest of Specification Standard Standard Standard Standard Standard Standard Standard Standard Standard 9 mm Size Encoder 43 Order Number Size (mm) Number of Pulses Detents Shaft lenght (mm) Shaft Style STRK09EC1 9 mm 15 15 25 mm Flat STRK09EC2 9 mm 15 15 25 mm Flat STRK09EC1 STRK09EC2 Unit: (mm) Attachement With Push lock function With Push lock switch No Rest of Specification Standard Hollow Shaft Encoder 44 Order Number Model Positions Size Life cycles STSRGP1 STSRGP2 STSRGPWJ STSRGPSJ1 24 20 10 16 24 20 20 32 Refer to drawing Refer to drawing Refer to drawing Refer to drawing 100.000 cycles 50.000 cycles 50.000 cycles 50.000 cycles Standard Specifications: Ratings: max. Operating Current: Insulation Resistance: Withstand Voltage: STSRGP1 STSRGP2 STSRGPWJ STSRGPSJ1 Unit: (mm) 10mA 5 VDC 10mA 100V DC 10 M min. 100V AC Magnetic Encoder Order Number Size (mm) Number of Pulses Detents Details Shaft lenght (mm) Shaft Style STEM20B41 20 40 40 LED: colour orange 10 STEM20B42 20 40 40 without LED 16 STEM11B01 11 16 16 Vertical Type 15 Flat 4 mm O Flat 4 mm O Flat Standard Specifications: Power Ratings: 5 VDC +/-5 Current consumption: 15mA max Output Phase: A,B (square wave) Life cycles: up to 1.000.000 cycles STEM20B41 STEM20B42 STEM11B01 Unit: (mm) 45 Attachement 31 LED's with push on switch 0,5 mm push on switch 0,5 mm push on switch 0,5 mm Rest of Specification Standard Standard Standard Keytop Product Line 46 for Tact Swiches Variety Colour Unit: mm Cap: Clear Keytop: Red Blue Ivory Black Yellow H12 H10 SKHC SKQE 1.5 3 4 Cap Key top Red Blue Ivory Black Yellow Cap: Clear Keytop: Red Blue Ivory Black Yellow H8 H6.5 H5 SKHJ 1.8 3.8 Cap Key top Red Blue Ivory Black Yellow SKHQ 2.5 H9.5 H8 H6 4 3 Cap Key top The knob is shipped with the switch, unmounted. 2. The label is not included. Cap: Clear Keytop: Red Blue Ivory Black Yellow SK2AA00010~00100(Keytop) (Stem of key switch) Unit: (mm) H10 SK2AA00510 SK2AA00010 SK2AA00020 SK2AA00030 SK2AA00040 SK2AA00050 Thickness 0.1 SK2AA00410 SK2AA00420 SK2AA00430 SK2AA00440 SK2AA00450 SK2AA00520 H6.5 SK2AA00210 SK2AA00220 SK2AA00230 SK2AA00240 SK2AA00250 SK2AA00460 SK2AA00470 SK2AA00480 SK2AA00490 SK2AA00500 H7.4 SKEC 1. Label Dimension 5.5 2.8 H4 SKHH Variety Model 4R 1 Models H8 SK2AA00530 SK2AA00110 SK2AA00120 SK2AA00130 SK2AA00140 SK2AA00150 ALPS ELECTRIC EUROPA GmbH Hansaallee 203 D-40549 Dusseldorf Telefon (49) 211-5977-0 Fax (49) 211-5977-146 E-Mail: alpseuropa@alps-europe.com www.alps-europe.com